Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
yachtpaint.com® ®
WHAT IS IT?Epiglue is a high performance marine and general purpose epoxy adhesive. Itsthixotropic (non-sagging) nature enables it to be used for both close contact andgap filling joints. It offers a virtually colourless glue line once cured and is suitablefor use both above and below the waterline. Its strong gluing properties make itideal for all your gluing requirements around the home, office, boat and work place.
ALU
MIN
IUM
SurfacePreparation
Sand/dust down
Sand/wash
Epiglue
SUITABILITY?Bonding – wood, metal, fibreglass, concrete, brickwork, glass, rubber, china, tiles,ceramics and some types of plastics or similar substrates or one to another.
ABS and the harder “crisper type plastics” can sometimes be bonded providedsome care is taken to roughen the surface first.
Rubber can be bonded but if the glue line is to be flexed or stretched heavily thenanother type of adhesive such as contact glue should be used.
BRAS
S
CAST
IRO
N
CER
AMIC
S
CON
CRET
E
FOR
MIC
A
POLY
ESTE
RR
ESIN
POLY
STYR
ENE
RU
BBER
STEE
L
WO
OD
ZIN
C
Degrease sand
Wash with water/dry
Take care when mixing Epiglue:
• Always adhere to the correct mixing ratio to ensure maximum bond.
• Avoid putting the resin stick in the hardener container and vice-versa.
• Use separate sticks for dispensing the product from the containers.
• Simple mixing ratio – refer below:
MIXING
2 Parts Resin : 1 Part Hardener. Make sure the product is mixed to a uniform colour
GUIDELINES FOR USE
• Ensure surface is clean and free from contamination and well abraded when surface is smooth to ensure maximum adhesion.
• Apply mixed glue to the surface to be bonded.
• Use clamps, screws, masking tape, clothes pegs etc. to hold joint in place.
• Remove excess glue with a rag.
• Adhere to drying times on the product label before putting article back into full use.
Akzo Nobel Pty LimitedE54 / 76 Waterway Drive, Coomera Q 4104Phone:+61 7 5573 9600Technical Helpline: 1800 251 431www.yachtpaint.com
Akzo Nobel Coatings Limited686 Rosebank Road,Avondale, AucklandTechnical Helpline: 0800 808 807
We have taken reasonable care in preparing this document and in collecting and preparing material for inclusion in it but donot represent or warrant that it is free from error or that the information content is complete or accurate. The statements andrecommendations are advisory only and all advice and products are provided on the terms set out in our standardConditions of Sale.
Akzo Nobel Logo, ®, International®, and other products mentioned in this document are trademarks of or licensed to AkzoNobel. © Akzo Nobel 2005
HANDY TIPS
• For small jobs look for the Handyman Blister Pack.
• Mix only enough to do the job at hand.
• Apply clamps where possible.
• Do not use on boric treated timber.
• After gluing in cold temperatures, place object in warm place, e.g. hot water cupboard.
• When gluing wood, test with a few drops of water on the surface first; if it beads up contamination is presenton the surface; re-sand the surface and solvent wipe.
• Not recommended on flexible joints or damp wet timber.
• Skin contact with glue can be cleaned up with warm soapy water, however, it is strongly recommended that disposable gloves be worn at all times.
• Tools can be cleaned with International Epoxy Thinners #7.
• Some plastics such as polypropylene, polyethylene andnylon cannot be bonded with Epiglue.
®