wiremold

The Sentrex High Performance Rack Mount Series andthe Perma Power Computer Grade Rack Mount andCabinetMATE Surge Protector Series offer a wide

range of solutions for communication closet, rack, and cab-inet applications. By dissipating and diverting excess volt-age, a Sentrex or Perma Power surge protection devicekeeps your critical systems functioning properly.

Surges can strike once a month or hundreds of times aday. They can penetrate a facility via AC, telephone, andcommunication lines, or on any wire that enters a building.Surges and noise are also generated inside a building by fluorescent lighting, electric motors, HVAC equipment and office machines. If left unprotected, sensitive communications equipment and valuable data can be damaged or destroyed.

Sentrex and Perma Power rack mount and CabinetMATEsurge protectors provide advanced protection for criticalelectronic and communications equipment. They are anintegral part of the Sentrex Zoned Approach to whole building protection.

High Performance and Computer GradeRack Mount and CabinetMATE® Surge Protectors

■ All lines are protected. Units provide surge protection on all three modes (L-N, L-G, and N-G). Units also have thermal protection on all three lines.

■ 400V UL1449 clamping level. Outstanding protection against harmful surges.

■ EMI/RFI noise reduction. Protects against data disruption due to electromagnetic or radio frequency interference.

■ Space saving. Rack mount units fit standard 19" [482mm] relay racks. Compact 1U design takes up minimum space. 23" [584mm] units available, consult factory.

■ Low profile. CabinetMATE units offer a narrow 1 1/2" x 1 3/16" [38mm x 20mm] aluminum housing.

■ Aesthetically pleasing. Rack mount units have a black matte finish and a black cord. CabinetMATE units have a gray finish and a black cord.

■ Cord properly rated to load requirements. 15A units have a 14/3 SJT cord and a NEMA 5-15P plug. 20A units have a 12/3 SJT cord and a NEMA 5-20P plug.

■ Lighted switch available on some units.

■ Protection indication. All units have a protection indication light to show the status of the unit.

■ Resettable circuit breaker. Provides overload protection.

■ Product warranty. Sentrex rack mount units come with a lifetime product warranty. Perma Power rack mount andCabinetMATE Series units come with a five-year product warranty.

■ UL and cUL Listed or Recognized. Rack mount units are UL and cUL recognized to UL1449, the Standard forTransient Voltage Surge Suppressors, Second Edition. datedAugust 15, 1996, including requirements effective February 9,2007. CabinetMATE units are UL and cUL Listed to UL1449,Second Edition, dated August 15, 1996, including requirementseffective February 9, 2007.

Features & Benefits

ED638R6 – Updated February 2007 – For latest specs visit www.wiremold.com

R5BZ20 (Front & Back)

R8BZ (Front & Back)

SURGE

Sentrex® andPerma Power®

Surge Protection Circuitry 3 element, 3 stage hybrid circuitUL1449 Clamping Level 400 Volts (330V L-N only)Maximum Surge Current 56,000 Amps (32,000 Amps L-N, 12000 Amps L-G, 12000 Amps N-G)Noise Reduction +50 dBResponse Time Less than 1 nanosecondProduct Warranty Lifetime

2

Catalog No./Item Description/Specifications

R5S/R5S-15 High Performance Surge Protector – Six rear outlets, lighted switch. 6' [1.8m] or 15' [4.6m] cord.

Sentrex High Performance Surge Protectors

Sentrex High Performance Rack Mount Specifications

Surge Protection Circuitry Single StageUL1449 Clamping Level 400 VoltsMaximum Surge Current 36,000 Amps (12,000 Amps L-N, 12,000 Amps L-G, 12,000 Amps N-G)Noise Reduction +35 dBResponse Time Less than 1 nanosecondProduct Warranty 5-Year


R5BZ20/R5BZ20-15 20A Computer Grade Surge Protector – Six 20A rear outlets.On/off switch. 6' [1.8m] or 15' [4.6m] cord.

R5BZ20X/R5BZ20X-15 20A Computer Grade Surge Protector – Six 20A rear outlets. 6' [1.8m] or 15' [4.6m] cord.


R8BZ/R8BZ-15 Computer Grade Surge Protector – Eight rear outlets, lighted switch. Receptacles rotated 90° and 4 outlets spaced to accommodate transformers. 6' [1.8m] or 15' [4.6m] cord.

R5BZ/R5BZ-15 Computer Grade Surge Protector – Six rear outlets, lighted switch. 6' [1.8m] or 15' [4.6m] cord.

R5BZX/R5BZX-15 Computer Grade Surge Protector – Six rear outlets. 6' [1.8m] or 15' [4.6m] cord.

Perma Power Computer Grade Surge Protectors

Perma Power Computer Grade Rack Mount Specifications

Surge Protection Circuitry Single StageUL1449 Clamping Level 400 Volts (330 L-N only)Maximum Surge Current 36,000 Amps (12,000 Amps L-N, 12,000 Amps L-G, 12,000 Amps N-G)Noise Reduction +35 dBResponse Time Less than 1 nanosecondProduct Warranty 5-Year

3

Catalog No./ Description/Item Specifications

4810BCS/ CabinetMATE Surge 4810BDS Protector – Ten

outlets. 6' [1.8m] or 15' [4.6m] cord.Length 48" [1.2m].


7712BCS/ CabinetMATE Surge 7712BDS Protector – Twelve

outlets. 6' [1.8m] or 15' [4.6m] cord.Length 77" [2m].


7011BCS/ CabinetMATE Surge 7011BDS Protector – Eleven

outlets. 6' [1.8m] or 15' [4.6m] cord.Length 70" [1.8m].

15A CabinetMATE Surge Protectors

CabinetMATE Specifications

j j j

Wiremold / LegrandU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-6251Canada:570 Applewood Crescent • Vaughan, Ontario L4K 4B41-800-723-5175 • FAX 905-738-9721

ED638R6 – Updated February 2007 – For latest specs visit www.wiremold.com© Copyright 2007 Wiremold /Legrand All Rights Reserved

Questions? Call Technical Support today at 1-800-SENTREX.

Catalog No.:4810BCS20R/4810BDS20R

Description/Item Specifications:20A CabinetMATE Surge Protector – Ten 20A outlets with t-slots. 6' [1.8m] or 15' [4.6m] cord. Length: 48" [1.2m].


Description/Item Specifications:20A CabinetMATE Surge Protector – Twelve 20A outlets with t-slots. 6' [1.8m] or 15' [4.6m] cord. Length: 77" [2m].


Description/Item Specifications:20A CabinetMATE Surge Protector – Eleven 20A outlets with t-slots. 6' [1.8m] or 15' [4.6m] cord. Length: 70" [1.8m].

20A CabinetMATE Surge Protectors

j j j


Description/Item Specifications:20A CabinetMATE Surge Protector – Eight 20A outlets with t-slots. 6' [1.8m] or 15'. Length: 20" [508mm].

j

The selection of steel, aluminum, and nonmetallic provides a versatile solution for many applications.Plugmold sections offer single or alternating circuits,

standard or isolated ground receptacles, and Snapicoil®

harnesses of prewired receptacles or cord ended units.Steel Plugmold comes in an ivory ScuffCoat™ or gray

enamel finish. The ScuffCoat finish is scratch resistant andprotects against nicks and chips while preventing color fromfading.

Aluminum Plugmold offers an attractive choice for hospital and commercial labs. The finish offers high-techaesthetics and corrosion resistance.

Nonmetallic Plugmold has a textured ivory finish withduplex receptacles. This series offers a field serviceablesurge module that protects the entire Plugmold strip andmakes on-site changes easy.

Plugmold®

Systems

Features & Benefits■ Steel, aluminum, or nonmetallic material. Variety provides

choice for the application.■ Many finishes. Ivory ScuffCoat finish or gray surface for steel,

aluminum satin anodized, and ivory nonmetallic textured finish.■ Compact, low profile appearance. Requires minimal space.■ Full range of fittings. Provides a complete wiring solution.■ Single, alternating circuit, and isolated ground receptacles

available. Meets virtually any job requirement. ■ Variety of lengths. Ideal for different spaces.■ Choose receptacle spacing. Suits many applications.■ Snapicoil harnesses with different lengths and receptacle

spacing. Offers a solution for many electrical requirements. ■ Duplex receptacle. Aesthetically pleasing, functional 20A

duplex for the 24S (2400) Series.

■ Single- and dual-gang boxes available. Wire devices into the raceway system.

■ Field replaceable surge module. Replaces the module, not a receptacle (NM2000 Series only).

■ Customization available. All products can be modified toaccommodate virtually any application.

■ 2400 Backfeed. Fitting helps installation over an existing wall box.

■ Datacom connectivity options. Accepts industry standardand proprietary devices from a wide range of manufacturers to provide a seamless and aesthetically pleasing interface forvoice, data, audio, and video applications at the point-of-use.

■ UL and cUL Listed. Safety and reliability in the applications.■ cUL Listed 24S (2400) Series Plugmold. This 20A

version is cUL Listed.

Steel, Aluminum, and Nonmetallic Plugmold Raceway and Multioutlet Assemblies

Plugmold Systems come in a variety of finishes and configurations.

Plugmold Systems shown in typical applications.

ED1025R7 – Updated February 2005 – For latest specs visit www.wiremold.com


Base and Cover Covers seambetween sections of 5400C.

V2003 Supporting Clip – For temporary2003 support, while positioning lengths

of raceway base. Use with V/G2000 Series. V2003 has ivory finish, 2003 has plated finish.

W30 Pressure-Type Wire Connector –For common connection of two,three, or four No. 12 or No.14 solidcopper conductors. Not forconnection of equipment groundingconductor. 300V maximum; 20A60° C maximum. Not for use withaluminum conductors.

2000WC Wire Clip – Holds conductors 2400WC in place in raceway.AL2000WCAL2400WCNM2000WC

2001 Coupling – For joining lengths of 2000 Series Raceway Base. atany point

desired. Base come together.

V2006* Cover Clip – For covering G2006* joint where lengths of cover

or base adjoin. Use withV/G 2000 Series.

V2010A3* Entrance End – Offers larger G2010A3* capacity than V2010A2. 1/2"

trade size KOs on end, each side and bottom. 3/4" trade size KOs on bottom and rear. Includes ground screw. Use with V/G 2000 Series.

V2010A2* Entrance End – For connecting G2010A2* V2000 with 1/2" conduit and

armored cable connectors. 1/2" trade size KOs on end, each side and bottom. Includes ground screw. Use with V/G 2000 Series.


2009 Ground Clamp – For connection of equipment grounding conductorto provide additional groundto raceway. Use with V/G2000 Series.

V2010B* Blank End Fitting – For closing G2010B* the open end of raceway.

Use with V/G 2000 Series.

V2051 Flush Plate Adapter – For feeding 2000 from an existing wall outlet. Equipped with 1/2" [12.7mm] threaded stud, toothed lockwasher for grounding, and conduit bushing.

V2011* 90º Flat Elbow – For right G2011* angle turns on same surface.

Cover stop permits neatbutting of 2000C Cover. Two couplings furnished.

2017TC Internal Corner Coupling – Furnished with one fiber bushing.

V2018C* External Elbow – To continue G2018C* raceway runs around outside

corner. Fills the gap when external corner is made by notching and bending the 2000 Base.

V2015* Tee – For branches at right G2015* angles. Couplings furnished.

* Use “V” prefix for Ivory finish and “G” prefix for Gray finish.

2"[51mm]

V/G 2000 Series

2

2"[51mm]

1 5/16"[33mm]

3/4"[19.1mm]

2 7/64"[53mm]

1 29/32"[47mm]

2 11/16"[67mm]

3 22/64"[94mm]

3"[76mm]

1 9/32"[58mm]

1 1/2"[38mm]

2 1/8"[54mm]

1 7/32"[31mm]

How 2009 is used.

3/4"[19.1mm]

Plugmold 2000 extended from wall outlet using 2051H.

2051H fastened to horizontally mountedwall box.

4 1/2"[114mm]

2051H fastened to vertically mounted wall box.

2 1/2"[64mm]Ea. Leg

1 1/2"[38mm]

1 1/2"[38mm]

2017TC

2017TC

2000B

2000B

2017TC used as a corner coupling.

2017TC used as a corner coupling and astraight-through fitting.

Cover gap filler snappedinto place in 2018C.

1 7/8"[48mm]

1 1/2"[38mm]

4"[102mm]

6"[152mm]

ITEM CAT NO. LENGTH MATERIAL

Base V/G 2000B-5* 5' [1.5m] .040 SteelCover V/G 2000C* 5' [1.5m] .025 SteelBase & Cover V/G 2000BC* 5' [1.5m] .025 Steel

3

trade size


2409 Ground Clamp – No. 10 ground screw provided. Use with V2400 Series.

V2410A Entrance End – For connecting V2400 with 1/2" trade size conduitand armored cable. Use withV2400 Series.

V2410B Blank End – For closing openend of V2400 Series.

V2410C Entrance End Fitting – Has 1/2"and 3/4" trade size KOs on end and bottom. Additional 1/2" tradesize KO on sides.



2401 Coupling – For joining lengths of raceway. Use with V2400 Series.


V2406 Cover Clip – For covering joint where lengths of cover or base adjoin. Use withV2400 Series (nonmetallic).

2"[51mm]

1 1/2"[38mm]

1"[25mm]


V2089E End Reducing Connector – For connecting V2000 with V500 Raceway through end of V2000.

rectangular KO for extension towall box. Base has #10 threaded

620 2000 Raceway Base andCover Cutter – Portable cutter for 2000 Cover and Base. Tool steel construction for clean and easy square cuts every time. Total manual operation.

620BCK Replacement Blade Kit – Replacement blades and die set for 620 Cutter.


V2048 Single Gang Device Box – G2048 Cover has twistouts for 2000,

V500, and V700 Raceway. Base has 1/2" trade KO andrectangular KO for extension towall box. Base has #10 threadedhole for ground connection.

V2048-2 Two-Gang Device Box – Coverhas G2048-2 Twistouts for 2000,V500, and V700 Raceway. Base has 1/2" trade KO and rectangular KO for extension towall box. Base has #10 threadedhole for ground connection.

V2089 Side Reducing Connector – For connecting V2000 with V500Raceway through side of V2000.orange receptacles. Couplings furnished.

V/G 2000 Series (continued)

1/2"[12.7mm]

2"[51mm]

1 5/8"[41mm]

1 3/16"[46mm]

1 3/16"[30mm]

2 7/8"[73mm]

1 3/4"[44mm]

1 3/4"[44mm]

4 5/8"[117mm]

4 3/4"[121mm] 4 3/4"

[121mm]

6"[152mm]

3 1/4"[83mm]

3/4"[19.1mm]

V2400 Series



Base V2400B 5' [1.5m] .040 SteelCover V2400C 5' [1.5m] .040 SteelBase & Cover V2400BC 5' [1.5m] .040 Steel

2 11/16"[68mm]

1 7/8"[48mm]

2 1/8"[54mm]


Base and Cover Covers seabetween sections of 5400C.


AL2003 Supporting Clip – Mount tosurface with No. 8 flathead screws. Use with AL2000 Series.


4


V2489 Side Reducing Connector – For connecting V2400 with V500 Raceway.

V2444 Extra Deep Device Box – V2444-2 Base has rectangular knockout

to enable extension from existing single-gang flush wall box and 1/2" and 1" concentric KOs. V2444 Cover has two twistouts for 500 and 700, and two twistouts for 2400. V2444-2 Cover has four 2400 Series twistouts.

624 2400 and 2400BD Raceway& Cover Cutter – Portable cutter for 2400B and 2400BDRaceway and Cover. Tool steel construction for clean and easy square cuts. Total manual operation.



V2411 90º Flat Elbow – For right angleturns on the same surface (nonmetallic cover).

V2417 Internal Elbow – For making internal corners (nonmetallic cover).

V2417M Internal Elbow – For making internal 90° corners. All steel construction.

V2418 External Elbow – For covering outside corners (nonmetallic cover).

V2451H Back Feed Fitting – For feeding V2400 Raceway from an existing outlet box. Equipped with 1/2" trade size male bushing and locknut washer for grounding.

V2448 Device Box – Cover V2448-2 has one twistout for 2400 on

each side and ends. Base has 1/2" trade KO and rectangular KO for extension to wall box. Base has #10 threaded hole for ground connection.

V2400 Series (continued)

1 5/8"[41mm]

1 5/8"[41mm]

CAT NO. L W D GANG #V2448 4 5/8" [117mm] 2 7/8" [73mm] 1 3/4" [44mm] 1V2448-2 4 3/4" [121mm] 4 3/4" [121mm] 1 3/4" [44mm] 2

2 3/4"[70mm]

4 3/4"[121mm] 4 3/4"

[121mm]

WL

D

15/16"[23.8mm]

2 1/16"[52mm]

3 7/8"[98mm]


1 3/4"[45mm]

1 29/32"[49mm]

4 1/2"[114mm]

4 1/2"[114mm]

AL Series


Base AL2000B-5 5' [1.5m] .060 AluminumCover AL2000C-5 5' [1.5m] .060 AluminumBase AL2000B-10 10' [3.m] .060 AluminumBase AL2400B-5 5' [1.5m] .060 AluminumCover AL2400C 5' [1.5m] .060 AluminumBase AL2400B-10 10' [3.m] .060 Aluminum

1 7/16"[37mm]

5


AL2011 90º Flat Elbow – For right AL2411 angle turn on same surface.

Comes with two couplings.

AL2015 Tee – For branch connection of AL2415 two runs of AL2000 Raceway.

Three couplings furnished.

AL2416 Cross – For cross connection of two runs of AL2400 Raceway. Four couplings furnished.

AL2017 Internal Elbow – For bendingAL2417 around internal corners. Two

couplings furnished.

AL2018 External Elbow – For makingAL2418 90º external corners. Two

couplings furnished.

AL2038 Round Fixture Box (Solid Base) – Designed for use in hanging fixtures. Cover takes any devicewith mounting screw centers of2 3/4", 3 1/2", and 4 1/16" [70mm, 89mm, and [103mm]. Base has concentric 1/2" and 3/4" KO.

AL2040A In-line Single Pole Switch – Single pole 120V switch. Two couplings furnished.

AL2043 In-line Receptacle – Two 15A, 120V U-ground factory wiredreceptacles. Couplings furnished.

Catalog No./Item Description/Specification

AL2000WC Wire Clip – Holds conductors AL2400WC in place in raceway (nonmetallic).

AL2001 Coupling – For joining lengthsAL2401 of raceway. Use with AL2000

and AL2400 Series.

AL2006 Cover Clip – For covering AL2406 joint where lengths of cover

or base adjoin. Use withAL2000 and AL2400 Series.

AL2009 Ground Clamp – Use with AL2000 Series.

AL2409 Ground Clamp – Use withAL2400 Series.For connection

AL2010A End Fitting – With 1/2" hub adapter. Use with AL2000 Series.

AL2410B2 End Fitting – With 1/2" plastic KO. Use with AL2400 Series.

AL2010B Blank End – Use with AL2000 Series.

AL2410B Blank End – Use with AL2400 Series.

AL2051 Box Adapter – For feeding AL2451 raceway from an existing

wall outlet.

A

ACAT NO. AAL2017 3" [76mm]AL2417 4" [102mm]

B

BA

CAT NO. A BAL2018 1 7/8" [48mm] 3" [76mm]AL2418 3" [76mm] 5" [127mm]

C

BA

4 13/16"[122mm] 1 3/8"

[35mm]

6"[152mm]

6"[152mm]

3"[76mm]

1 3/4"[44mm]

#8 Ground StudW/Cup Washer

1 3/8"[35mm]

1 1/4"[32mm]

2"[51mm]

1"[25mm]

1"[25mm]

1 3/8"[35mm]

1 1/4"[32mm]

2"[51mm]

4 1/2"[114mm]

4 1/2"[114mm]

C

A B

6"[152mm]

6"[152mm]

2"[51mm]

CAT NO. A B CAL2011 3" [76mm] 3" [76mm] 1 9/16" [40mm]AL2411 4" [102mm] 4" [102mm] 2" [51mm]

CAT NO. A B CAL2015 1 7/16" [37mm] 4" [102mm] 1 9/16" [40mm]AL2415 4" [102mm] 6" [152mm] 2" [51mm]

AL Series (Continued)

CAT NO. L W

AL2001 1 5/8"[41mm] 1 1/2" [38mm]AL2401 3" [76mm] 1 3/4" [44mm]

1"[25mm]

1 1/2" [38mm]

#8 Ground StudW/Cup Washer

W

L

6


Base and Cover

NM2003 Supporting Clip – Mount to surface with No. 8 flathead screw. Use with NM2000 Series.


NM2006 Cover Clip – For covering joint where lengths of cover or base adjoin. Use withNM2000 Series.

NM2011 90º Flat Elbow – For right angle turns on same surface.


NM2017 Internal Elbow – For right turns at inside corners.

NM2018 External Elbow – Used for making 90º turns at outside corners.

NM2010A Entrance End – Has 1/2" tradesize KO on end and bottom. Usewith NM2000 Series.

NM2010B Blank End Fitting – Use withNM2000 Series.

NM2000 Series

2"[51mm]

1 3/4"[44mm]

1 1/2"[38mm]

1 3/8"[35mm] 1"

[25mm]

1"[25mm]

2 11/16[68mm]

1 7/8"[48mm]

3 3/16"[81mm]

2"[51mm]

2"[51mm]

1 7/8"[73mm]

2"[51mm]

1 5/8"[41mm]


Base NM2000B 8' [2.4m] PVC-IvoryCover NM2000C 8' [2.4m] PVC-IvoryBase & Cover NM2000BC 5' [1.52m] PVC-Ivory


AL2043IG In-line Isolated GroundReceptacle – Two 15A, 120V factory wired, isolatedground, orange receptacles.Couplings furnished.

AL2044 Deep Device Box – For AL2044-2 receptacles and deep devices

such as those of signal and alarm systems. Base has open back plate for mounting to existing wall box and solid back plate insert with 1/2" and 3/4" KO to close opening.


AL2047 Shallow Switch and Receptacle Box – Designed forstandard shallow switches andreceptacles. Base has open backplate for mounting to existing wall box and solid back plate insert with 1/2" and 3/4" KO to close opening.

AL2446P-D Duplex Receptacle Cover Plate – For in-line mounting of commercially available duplex receptacles.

AL Series (Continued)

6" [152mm]

6" [152mm]

W L

D

LW

D

CAT NO. L W D GANG #AL2044 4 5/8" [117mm] 3 1/16" [73mm] 2 1/4" [57mm] 1AL2044-2 4 5/8" [117mm] 4 27/32" [121mm] 2 1/2" [64mm] 2

CAT NO. L W D GANG #AL2047 4 5/8" [117mm] 3 1/16" [73mm] 1 3/8" [35mm] 1AL2047-2 4 5/8" [117mm] 4 27/32"[121mm] 1 3/8" [35mm] 2

1 3/4"[44mm]

3 3/8"[86mm]

1 1/2"[38mm]

1 9/16"[40mm]

1 3/4"[44mm] 3 13/16"

[97mm]

1 3/4"[44mm]

1 15/16"[49mm]

1 1/16"[27mm]

7


NM2051H Wall Box Adapter – For feeding NM2051V raceway from an existing wall

outlet; horizontal or vertical applications. Provides completeaccess to wall box for connections.

NM2011 90º Flat Elbow – For right angle turns on same surface.

NM2017 Internal Elbow – For right turns at inside corners.

NM2018 External Elbow – Used for making 90º turns at outside corners.

NM2027S Surge Suppression Module –Field installed replacement module forSGB Series surge strips. Protects allreceptacles on the strip. Contains indicator light for proper operation of the suppression module. Suppression three legs.

2"[51mm]

2"[51mm]

1 7/8"[73mm]

Standards UL recognized under the component program of UL Standard 1449, as defined by ANSI/NFPA 70-1990.

Service Voltage 120Vrms nominal operating voltage.

Maximum Continuous Operating Voltage 150Vrms.

Suppression Voltage (Three Line Protection) Complete surge protective device as assessed by UL:

Actual let through voltage at 6kA 1.2/50µs, 340 Volts Peak L-N.500A, 8/20µs

Maximum Single Withstand Surge Current No less than 39kA individually between L-N, L-G, and N-G, based on the sum of the device components.

Suppression UL1449Mode Suppression Voltage

Line – Neutral 500V

Line – Ground 500V

Neutral – Ground 500V

Specifications for Surge Module


NM2015 Tee – For branches at right angles. raceway. Four couplings

furnished.

NM2044 Extra Deep Device Box – Formounting power/communicationdevice when additional depth isrequired. Has combinationtwistouts for 2700, 2800, 2900, and NM2000.

NM2048 Sure Snap® Device Box – Cover snaps onto base, no screws required. Cover has twistouts on all sides. Rectangular KO inbase for extension to wall box.

NM2027-15 Replacement Receptacles – 15A and NM2027-20 20A replacement devices. 6" [152mm]

wire leads each side.

3 3/16"[81mm]

3 3/16"[81mm]

1/2"[12.7mm]

1 1/8"[29mm]

4"[102mm]

W

L

D

2 3/4"[70mm]

4 1/2"[114mm]

2 3/4"[70mm]

4 1/2"[114mm]

4 1/2"[114mm]

1 7/8"[48mm]

1 5/16"[33mm] 3 11/16"

[94mm] 1"[25mm]

1 5/8"[41mm]

CAT NO. L W D GANG #NM2048 4 3/4" [121mm] 3" [76mm] 1 3/4" [44mm] 1

NM2048-2 4 3/4" [121mm] 4 7/8" [124mm] 1 3/4" [44mm] 2

CAT NO. L W D GANG #NM2044 4 3/4" [121mm] 3" [76mm] 1 3/4" [44mm] 1NM2044-2 4 3/4" [121mm] 4 7/8" [124mm] 1 3/4" [44mm] 2

W

L

D

NM2000 Series (Continued)

1 3/8"[35mm] 1"

[25mm]

1"[25mm]

2 11/16[68mm]

1 7/8"[48mm]

3 3/16"[81mm]

2"[51mm]

1 5/8"[41mm]

8

WIRING OUTLETS CATALOG NO. LENGTH CONFIG CENTER DISTANCE QUANTITY HOUSING

20GB306* 3' [915mm] GB 6" [152mm] 6 Single 15A SteelAL20GB306 3' [915mm] GB 6" [152mm] 6 Single 15A Aluminum

AL20IG306 3' [915mm] IG 6" [152mm] 6 Single 15A Aluminum

24S3612GBX99IV 3' [915mm] GB 12" [305mm] 3 Duplex 20A Steel – Ivory

24S3612GBA99IV 3' [915mm] GBA 12" [305mm] 3 Duplex 20A Steel – Ivory

NM24GB412 4' [1.2m] GB 12" [305mm] 4 Duplex 20A PVC – Ivory

NM24GBA412 4' [1.2m] GBA 12" [305mm] 4 Duplex 20A PVC – Ivory



NM20IG412 4' [1.2m] IG 12" [305mm] 4 Duplex 15A PVC – Ivory

NM20SGB412 4' [1.2m] SGB-Surge 12" [305mm] 3 Duplex 15A PVC – Ivory

20GB506* 5' [1.5m] GB 6" [152mm] 10 Single 15A Steel


20GBA512* 5' [1.5m] GBA 12" [305mm] 5 Single 15A Steel

20IG512* 5' [1.5m] IG 12" [305mm] 5 Single 15A Steel

24S6012GBX99IV 5' [1.5m] GB 12" [305mm] 5 Duplex 20A Steel – Ivory

24S6012IGX99IV 5' [1.5m] IG 12" [305mm] 5 Duplex 20A Steel – Ivory

24S6012GBA99IV 5' [1.5m] GBA 12" [305mm] 5 Duplex 20A Steel – Ivory

AL20GB506 5' [1.5m] GB 6" [152mm] 10 Single 15A Aluminum


AL20IG506 5' [1.5m] IG 6" [152mm] 10 Single 15A Aluminum








NM20IG512 5' [1.5m] IG 12" [305mm] 5 Duplex 15A PVC – Ivory

NM20SGB512 5' [1.5m] SGB-Surge 12" [305mm] 4 Duplex 15A PVC – Ivory

Plugmold Multi Outlet Strip


GB Series:3-wire, #12 THHN (1 hot,1 neutral and 1 ground),1 circuit; has insulatedgrounding conductor.

GBA Series:4-wire, #12 THHN (2 hot, 1neutral and 1 ground), 2 circuit;outlets wired alternately; hasinsulated grounding conductor.

IG Series:3-wire, #12 THHN (1 hot, 1 neutral and 1 ground), 1 circuit;has insulated-isolated groundingconductor. Orange receptacles.

Wiring Configuration

GB Series:3-wire, #12 THHN (1 hot, 1 neutraland 1 ground), 1 circuit; hasinsulated grounding conductor.

GBA Series:4-wire, #12 THHN (2 hot, 1 neutral and 1 ground), 2 circuit; outlets wired alternately; hasinsulated grounding conductor.

NOTE: SNAPICOIL REELS on custom order. Snapicoil is available on reels if lengths greater than 50’ are needed, or if multiple lengths are required for production-type jobs. The maximum length per reel is 240’ for Snapicoil with outlets 12” and 18” on centers; 500’ with outlets 30” on center. Packaging includes the necessary number of lengths of base, holecut cover, wire clips, and couplings for complete installation. Price and delivery information should be obtained prior to specifying or ordering. To specify or order, add R to the Snapicoil number. Ex: V20GB06R. Other outlet spacings available on custom order.Receptacles are made from high impact thermoplastic. V2000 Plugmold is supplied with two (2) V2010B Blank End Fittings and (1) 2001 Base Coupling. NM2000 Plugmold strips are supplied with two (2) NM2010B Blank End Fittings.

With Snapicoil

9

WIRING OUTLETSCATALOG NO. LENGTH CONFIG CENTER DISTANCE QUANTITY HOUSING







20GBA618* 6' [1.8m] GB 18" [457mm] 4 Single 15A Steel

20IG606* 6' [1.8m] IG 6" [152mm] 12 Single 15A Steel













AL20GBA606 6' [1.8m] GBA 6" [152mm] 12 Single 15A Aluminum





NM24GB612 6' [1.8m] GB 12" [305mm] 6 Duplex 20A PVC-Ivory


NM24GBA612 6' [1.8m] GBA 12" [305mm] 6 Duplex 20A PVC-Ivory






NM20IG612 6' [1.8m] IG 12" [305mm] 6 Duplex 15A PVC-Ivory

NM20SGB612 6' [1.8m] SGB-Surge 12" [305mm] 5 Duplex 15A PVC-Ivory

NM20SGB618 6' [1.8m] SGB-Surge 18" [457mm] 3 Duplex 15A PVC-Ivory

* Use “V” prefix for Ivory finish and “G” prefix for Gray finish. Outlets match raceway finish.

Plugmold Multi Outlet Strip (Continued)


CATALOG WIRING OUTLETS (15A 120V NEMA 5-15SR) HOLE CUT COVERNO. LENGTH CONFIG CENTER DISTANCE QUANTITY QUANTITY LENGTH HOUSING

20GB12* 48' GB 12" [305mm] 48 Single 8 6' [1.8m] Steel

20GB18* 48' GB 18" [457mm] 32 Single 8 6' [1.8m] Steel

V20GB30 50' GB 30" [760mm] 20 Single 10 5' [1.5m] Steel-Ivory

NM20GB12 48' GB 12" [152mm] 24 Duplex 8 6' [1.8m] PVC-Ivory

20GBA12* 48' GBA 12" [305mm] 48 Single 8 6' [1.8m] Steel

NM20GBA12 48' GBA 12" [305mm] 24 Duplex 8 6' [1.8m] PVC-Ivory

Plugmold with Snapicoil Harness

10


UNIT OUTLETS CIRCUITCAT NO. LENGTH QUANTITY CORD SET LENGTH TYPE SWITCH BREAKER HOUSINGNM20-C3 3' [.92m] 3 Duplex 6' [1.8m] 14/3 SJT Yes Yes PVC-Ivory20-C2* 3' 4" [1m] 6 Single 6' [1.8m] 12/3 SJT No Yes SteelNM20-C4 4' [1.2m] 4 Duplex 6' [1.8m] 14/3 SJT Yes Yes PVC-IvoryNM20-C5 5' [1.5m] 5 Duplex 6' [1.8m] 14/3 SJT Yes Yes PVC-IvoryNM20-C6 6' [1.8m] 6 Duplex 6' [1.8m] 14/3 SJT Yes Yes PVC-Ivory

Cord-Ended Plugmold Series

CABLE WIRE SIZE O.D. NUMBER OF CONDUCTORS (40% FILL)TYPE THHN/THWN Inches [mm] V2000 V2400 NM2000 AL2000 AL2400

POWER WIRING 8 AWG 0.216 [5.5] – – – 12 18WITHOUT DEVICES 10 AWG 0.166 [4.2] – 26 15 24 37

12 AWG 0.130 [3.3] 7* 41 31 38 5814 AWG 0.111 [2.8] 7* 57 45 51 78

POWER WIRING 8 AWG 0.218 [5.5] – 2 – – 4WITH DEVICES 10 AWG 0.153 [3.9] – 6 – 3 8(PLUGMOLD) 12 AWG 0.122 [3.1] 5* 10 8** 6 12

14 AWG 0.105 [2.7] 5* – 8** 8 16

Wire Fill Capacities for Power

*Wire capacity limited to maximum of seven conductors due to .025" [.6mm] material thickness of cover.**Including one hot, neutral, and ground wire from the receptacle.

11


AL2400 Base and Cover – 6063-T5 extruded aluminum, satin anodized finish, .060" [1.5mm] nominal thickness.

NM2000 Base and Cover – Extruded PVC, ivory textured finish.


2000 Base and Cover – Base – 2000B .040" [1.0mm] steel.Cover – 2000C .025" [.6mm] steel.

V2400 Base and Cover – Base – V2400B .040" [1.0mm] steel.Cover – V2400C .040" [1.0mm] steel.

AL2000 Base and Cover – 6063-T5 extruded aluminum, satin anodized finish, .060" [1.5mm] nominal thickness.

Cross Section

1"[25mm]

1 9/32"[33mm]

1 7/16"[37mm]

1 1/8"[29mm]

1 29/32"[48mm]

7/8"[22.2mm]

3/4"[19.1mm]

2"[51mm]

1 9/32"[33mm]

1 3/4"[44mm]

Cross-Sectional Area:0.80in2 [516mm2]




Cross-Sectional Area:1in2 [645mm2]

Now you have a wide range of options for providing datacom connectivity into Wiremold® Cable Management Systems. They are:

• Ortronics® TracJack® and Series II Modular Connectivity Solutions • Pass & Seymour Activate™ Modular Inserts • Open System Communication Modules

Use these icons to determine connectivity options for each Wiremold System component:

Ortronics® Connectivity

TracJack® Individual Jack System • Front-loading, snap-in design supports future moves adds and changes • Inserts for voice, data, audio, and video • Available Category 3, 5e, 6, USOC 6-position, and other media• Flat or angled 45° exit configurations • Choice of 13 colors and color matched to Wiremold Systems • Universal T568A/B wiring format

Series II Front-Loading, Module System • Module design features easy snap-in front-loading design • Linear 110 punch down format for easy termination • Inserts for voice, data, audio, and video • Available Category 3, 5e, 6, USOC 6-position, and other media• Available in flat or angled 45° exit configurations • Color matched to Wiremold Systems

For detailed product selection refer to the Ortronics Catalog or visit www.ortronics.com.

Pass & Seymour Legrand Network Wiring

Activate™ Series Front-Loading Inserts • Modular inserts for voice, data, audio and video applications • Front-load, snap-in design • Color and texture matched to Wiremold Systems • Available Category 3, 5e, 6, as well as 6-position USOC • Universal T568A/B wiring format

For detailed product selection refer to the Pass & Seymour Network Wiring Catalog or visit www.passandseymour.com.

Open Connectivity Solutions

Wiremold Open System Communications Modules • Accommodate a wide range of manufacturers’ communications outlets including

keystone jacks, as well as proprietary solutions from Avaya (Lucent) and NORDX • Modules insert into a wide range of Wiremold Systems • Pre-punched faceplates accept common communication devices

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

Datacom Connectivity Options

NOTE: For more information on integrating connectivity into Wiremold Cable Management Systems contact the Wiremold Applications Engineering Team or your local Wiremold Sales Representative.


ED1025R7 – Updated February 2005 – For latest specs visit www.wiremold.com© Copyright 2005 The Wiremold Company All Rights Reserved

■ One-piece design. Easy to handle and install.

■ Easy open and snap-close latch. Installations, moves, and changes are quick and easy.

■ Durable, flexible hinge construction. Allows for repeated openings and closings while maintaining product integrity and aesthetics.

■ Adhesive backing. Makes installation quick and easy.

■ Fiber compliant fittings. Maintain 1 1/4" [32mm] bendradius for UTP and fiber optic cable..

■ Available in three low profiles, in both 6' & 8' [1.8m &2.4m] lengths. Allows flexibility for cabling requirements.Six- and eight-foot [1.83m and 2.4m] lengths minimize cutting, cover clips, and scraps.

■ Made of durable impact-resistant PVC. Easy to cut and trim.

■ Full selection of fittings. Surface mount boxes, and multiport workstation outlets makes installations quick and easy.

■ Available in three standard colors. Standard colors are ivory, white, and fog white. Consult factory for customcolors. Paintable using latex paint.

■ Datacom connectivity options. Accepts industry standard and proprietary devices from a wide range of manufacturers to provide a seamless and aestheticallypleasing interface for voice, data, audio, and video applications at the point of use.

The Uniduct Nonmetallic Latching RacewaySystem is a one-piece single channel design,ideally suited to route and protect fiber

optic, UTP, and and other low-voltage (50V or less)cables in an easy to install and aesthetically pleasing application.

The 2800 and 2900 Fiber Optic (FO) fittings maintain a 1 1/4" [32mm] bend radius and are theperfect solution for even the most demandingcabling applications.

UNIDUCT®

Latching Raceway

Uniduct One-Piece Latching Raceway

Features & Benefits

ED264R6 – Updated April 2006 – For latest specs visit www.wiremold.com

The Uniduct design features a co-extruded flexible PVC hinge

that prevents cracking and splitting even after numerous

openings and closings.

2700 2800 2900

F

C

B

A

EC

D

H

G

I

J

2

Uniduct 2700, 2800, 2900 Series Latching Raceway System Layout

NOTE: Illustration is for showing product applications only.

A —2710B, 2810B, 2910B Blank End FittingB —2706, 2806, 2906 Cover ClipC —2715, 2815, 2915 Tee FittingD —CM-MMB-293 Multimedia BoxE —2718, 2818, 2918 External Elbow

F —2786, 2886, 2986 Drop Ceiling ConnectorG —2717, 2817, 2917 Internal ElbowH —2711, 2811, 2911 Flat ElbowI —NM2048 Device Box J —CM2, Series II, Tracjack Communication Device

NOTE: Wire capacity is reduced to allow for proper conductor bend radius and maximum permissible heat rise.* Category 6 augmented (6a) cable for 10 gigabit ethernet – max allowed cable diameter per addenda No. 11 ANSI TIA/EIA 568-B.2.

CABLE CATEGORY/ O.D. 2700 RACEWAY 2800 RACEWAY 2900 RACEWAYTYPE DESIGNATION Inches [mm] 40% FILL 40% FILL 40% FILL

UNSHIELDED 4-pair, 24 AWG Cat 3 0.190 [4.8] 2 4 12TWISTED PAIR 4-pair, 24 AWG Cat 5e 0.210 [5.3] 1 3 10

4-pair, 24 AWG Cat 6 0.250 [6.3] 1 2 74-pair, 24 AWG Cat 6a* 0.354 [8.9] 0 1 3

25-pair, 24 AWG 0.410 [10.4] 0 1 2

COAXIAL RG6/U 0.270 [6.9] 1 2 6

FIBER ZipCord 0.118 x 0.236 [3 x 6] 2 4 12Round 4 Strand Fiber 0.187 [4.8] 2 4 12Round 6 Strand Fiber 0.256 [6.5] 1 2 6

Uniduct 2700, 2800, 2900 Series Latching Raceway Wire Fill Capacity Chart

3


2700/2700L8 Latching Raceway – One-2800/2800L8 piece latching raceway with2900/2900L8 co-extruded design, smooth

plastic finish. Available in 6' [1.8m] and 8' [2.4m] lengths.

2706 Cover Clip – For covering jointwhere two pieces of 2700 SeriesRaceway Cover come together.

2710B Blank End Fitting – For closingopen end of 2700 Series Raceway.

2711 90° Flat Elbow – For right angleturns on same surface.

2715 Tee – For branching of racewayrunning at right angles.

2717 Internal Elbow – For right angle turns around internal corners.

2718 External Elbow – For right angleturns around external corners.

2786 Drop Ceiling Connector – Fordropping cables from ceiling intothe raceway.


1"[25mm]




2811FO 1 1/4" [32mm] Bend Radius FlatElbow – For right angle turns on same surface. Maintains 1 1/4" [32mm] bend radius wheninstalling UTP and fiber optic cable.


2815FO 1 1/4" [32mm] Bend Radius Tee – For branching of raceway at right angles. Maintains 1 1/4"[32mm] bend radius when installing UTP and fiber optic cable.


2817FO 1 1/4" [32mm] Bend RadiusInternal Elbow – For right angleturns around internal corners. Maintains 1 1/4" [32mm] bendradius when installing UTP and fiber optic cable.


2818FO 1 1/4" [32mm] Bend RadiusExternal Elbow – For right angleturns around external corners. Maintains 1 1/4" [32mm] bendradius when installing UTP and fiber optic cable.

Fittings for Uniduct Latching Raceway

1" [25mm]Each Leg

1 1/8" [29mm]Each Leg



2 3/16"[56mm]

11/16"[17mm]

7/8"[22mm]

3 "[76mm]

3 3/4"[95mm]

2 1/2"[64mm]

3 1/4"[83mm]

1 15/16"[49mm]

1 1/4"[32mm]

3 1/2"[89mm]

5"[127mm]

2 7/8"[73mm]

1"[25mm]

1 3/8"[35mm]

1 1/2"[35mm]


2" [51mm]Each Leg

3"[76mm]

2 1/4"[57mm]

2 1/8"[54mm]

1 7/16"[37mm]

NOTE: No suffix denotes Ivory finish. Add "WH" suffix for White finish and "FW" suffix for Fog White finish.

A

B

Cat. No. A B2700 3/8" [9.5mm] 3/4" [19.1mm]

2800 1/2" [12.7mm] 1" [25mm]

2900 3/4" [19.1mm] 1 1/2" [38mm]

4



2917FO 1 1/4" [32mm] Bend RadiusInternal Elbow – For right angleturns around internal corners. Maintains 1 1/4" [32mm] bendradius when installing UTP and fiber optic cable.


2918FO 1 1/4" [32mm] Bend RadiusExternal Elbow – For right angleturns around external corners. Maintains 1 1/4" [32mm] bendradius when installing UTP and fiber optic cable.


2989 Reducing Connector (2900 – 2800) – For transitioningfrom 2900 Series Raceway to 2800 Series Raceway.

2989A Reducing Connector (2900-2700) – For transitioningfrom 2900 Series Raceway to 2700 Series Raceway.



2889 Reducing Connector (2800 –2700) – For transitioning from 2800 Series Raceway to 2700 Series Raceway.




2911FO 1 1/4" [32mm] Bend Radius FlatElbow – Right angle turns on same surface. Maintains 1 1/4" [32mm] bend radius wheninstalling UTP and fiber optic cable.


2915FO 1 1/4" [32mm] Bend Radius Tee – For branching of raceway at right angles. Maintains 1 1/4"[32mm] bend radius when installing UTP and fiber optic cable.



1 1/8"[29mm]

3 7/8"[98mm]

3"[76mm]

3 3/4"[95mm]

2 1/2"[64mm]

3 1/4"[83mm]

1 15/16"[49mm]

1 1/4"[32mm]

4"[102mm]

5 1/2"[140mm]

1 3/4"[44mm]

2"[51mm]

3/4"[19.1mm]

15/16"[24mm]


3 1/2"[89mm]

2 1/4"[57mm]

1 9/16"[40mm]

2 3/8"[60mm]

Fittings for Uniduct Latching Raceway

2 7/8"[73mm]

2"[51mm]

NOTE: No suffix denotes Ivory finish. Add "WH" suffix for White finish and "FW" suffix for Fog White finish.

15/16"[24mm]

5


CM-MMB-291 One Insert Multimedia Box – Accepts one 2A size Wiremold Open System communication module or Pass & Seymour Activate series insert. Compatible with 2700 and 2800 Series Raceways.

CM-MMB-292 Two Insert FiberReady®

Multimedia Box – Fiber storage loop. Accepts two 2A size Wiremold Open System communication modules or Pass & Seymour Activate series inserts. Compatible with 2700, 2800, and 2900 Series Raceways.

CM-MMB-293 Three Insert FiberReady®

Multimedia Box – Fiber storage loop. Accepts three 2A size Wiremold Open System communication modules or Pass & Seymour Activate series inserts. Compatible with 2700, 2800, and 2900 Series Raceways.


NM2044* Extra Deep Device Box – For mounting voice/data devices when additional depth is required. Has combination twistouts for2700, 2800, 2900, and NM200 Series Raceways.

NM2044-2* Two-Gang Extra Deep Device Box – For mounting multiple voice/data devices when additional depth is required. Has combination twistouts for2700, 2800, 2900, and NM200 Series Raceways.

NM2048* Deep Device Box – For mounting deep voice/data interface devices. Has combination twistouts for 2700, 2800, 2900, and NM2000 Series Raceways.

NM2048-2* Two-Gang Deep Device Box – For mounting multiple voice/data devices. Has combinationtwistouts for 2700, 2800, 2900, and NM2000 Series Raceways.

Boxes for use with 2700/2800/2900 Series Raceway

4 3/4"[121mm]

4 3/4"[121mm]

4 7/8"[124mm]1 3/4"

[44mm]

1 3/4"[44mm]

3"[76mm]

Uniduct boxes with Pass & SeymourActivate Inserts. Activate Inserts can bemounted flush or angled, on either one-gang or two-gang boxes depending on the application.

4 3/4"[121mm]

4 7/8"[124mm]2 3/4"

[70mm]

3"[76mm]

4 3/4"[121mm]2 3/4"

[70mm]

3 1/4"[83mm]

3 1/4"[83mm]

1 1/2"[38mm]

5 3/16"[132mm]

5 3/16"[132mm]

1 1/2"[38mm]

5 3/16"[132mm]

7 3/4"[197mm]

1 1/2"[38mm]

NOTE: No suffix denotes Ivory finish. Add "WH" suffix for White finishand "FW" suffix for Fog White finish.

* Accepts industry standard NEMA faceplates for communication applications.

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

Fiber Compliant Fittings for 2800 and2900 Series Raceways. Maintain 1 1/4"[32mm] bend radius when installing UTPand fiber optic cable.

For ease of installing cables, the basehas cable retention fingers that hold the cables in place until the cover is installed.

6

Notes

7

Notes













keystone jacks, as well as proprietary solutions from Avaya (Systimax) and NORDX • Modules insert into a wide range of Wiremold Systems • Pre-punched faceplates accept common communication devices

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN




ED264R6 – Updated April 2006 – For latest specs visit www.wiremold.com© Copyright 2006 Wiremold / Legrand All Rights Reserved

The selection of lengths and fittings in a variety offinishes provides a versatile solution for manyapplications. Plugmold sections offer single or

alternating circuits, standard, or isolated ground receptacles,Snapicoil® harnesses of prewired receptacles, and cordended units.

Steel Plugmold comes in black or ivory ScuffCoat™ finishand white or gray enamel finish. The ScuffCoat finish isscratch resistant and protects against nicks and chips whilepreventing color from fading. The enamel finishes are neutralcolors that work with many decors or can be painted to integratewith most color schemes. Select Plugmold sections andfittings are now available in a durable stainless steel.

Plugmold® Systems

Features & Benefits■ Steel construction. Provides superior strength and

durability for any dry location installation.■ Many finishes. Black or ivory ScuffCoat finish, white or

gray enamel and select sections and fittings in stainlesssteel.

■ Compact, low profile appearance. Requires minimalspace.

■ Full range of fittings. Provides a complete wiring solution.■ Single, alternating circuit, and isolated ground

receptacles available. Meets virtually any job requirement. ■ Variety of lengths. Ideal for different spaces.■ Choose receptacle spacing. Suits many applications.

■ Snapicoil harnesses with different lengths andreceptacle spacing. Offers a solution for many electricalrequirements.

■ Duplex receptacle. Aesthetically pleasing, functional 20Aduplex for the 24S (2400) Series.

■ Single- and dual-gang boxes available. Wire devices into the raceway system.

■ Customization available. All products can be modified toaccommodate virtually any application.

■ cULus Listed. Safety and reliability in the applications.

Steel Plugmold Raceway & Multioutlet Assemblies

Plugmold Systems come in a variety of finishes and configurations.

Plugmold Systems shown in typical applications.

ED1412 – May 2006 – For latest specs visit www.wiremold.com

2


G2400 Base and Cover – V2400 Base – G2400B or V2400B

.040" [1.0mm] steel. Cover – G2400C or V2400C .040" [1.0mm] steel.Also available in custom colors.


2000* Base and Cover – Base – 2000B .040" [1.0mm] steel.Cover – 2000C .025" [.6mm] steel.

Cross Section

Plugmold 2000 System Layout

1 9/32"[33mm]

1 29/32"[48mm]

7/8"[22.2mm]

3/4"[19.1mm] Cross-Sectional Area:

0.80in2 [516mm2]


A — 2010B Blank End FittingB — 2051H Flush Plate AdapterC — 2006 Cover ClipD — 2017TC Internal Corner CouplingE — 2015 Tee FittingF — 2048-2 Two-Gang Device BoxG — 2018C External Elbow CoverH — 2048 Single-Gang Device BoxI — 2011 90° Flat Elbow

J — 20GB506 Plugmold StripK — 2089A Side-Reducing FittingL — 5748 Single-Gang Device BoxM — 500 RacewayN — 2010A2 Entrance End FittingO — 2010A3 Entrance End FittingP — 518 External ElbowQ — 2089E End-Reducing Connector

A

F

E

G

H

I

J

O

L

QPM

MN

K

BC

D

NOTE: Illustration is for showing product applications only.

* Use “V” prefix for Ivory ScuffCoat™ finish, “G” prefix for Gray enamel finish, “BK” for Black ScuffCoat™ finish, “WH” for white enamel finish, and “S” for stainless steel.



V2003 Supporting Clip – For temporary2003 support, while positioning lengths

of raceway base. Use with V/G2000 Series. V2003 has ivory finish, 2003 has plated finish.


2000WC Wire Clip – Holds conductors 2400WC in place in raceway.AL2000WC

2001 Coupling – For joining lengths of 2000 Series Raceway Base. atany point

desired. Base come together.

BK2006* Cover Clip – For covering G2006* joint where lengths of cover V2006* or base adjoin. Use withWH2006* V/G 2000 Series.S2006*

BK2010A3* Entrance End – Offers larger G2010A3* capacity than V2010A2. 1/2" V2010A3* trade size KOs on end, each WH2010A3* side and bottom. 3/4" trade

size KOs on bottom and rear. Includes ground screw. Use with V/G 2000 Series.

BK2010A2* Entrance End – For connecting G2010A2* V2000 with 1/2" conduit and V2010A2* armored cable connectors. WH2010A2* 1/2" trade size KOs on end, S2010A2* each side and bottom.

Includes ground screw. Use with V/G 2000 Series.

3


2009 Ground Clamp – For connection of equipment grounding conductorto provide additional groundto raceway. Use with V/G2000 Series.

BK2010B* Blank End Fitting – For closing G2010B* the open end of raceway. V2010B* Use with V/G 2000 Series.WH2010B*S2010B*

BK2051* Flush Plate Adapter – For G2051* feeding 2000 from an existing V2051* wall outlet. Equipped with 1/2" WH2051* [12.7mm] threaded stud, toothed S2051* lockwasher for grounding, and

conduit bushing.

BK2011* 90º Flat Elbow – For right G2011* angle turns on same surface. V2011* Cover stop permits neatWH2011* butting of 2000C Cover. S2011* Two couplings furnished.

2017TC Internal Corner Coupling – Furnished with one fiber bushing.

BK2018C* External Elbow – To continue G2018C* raceway runs around outside V2018C* corner. Fills the gap when WH2018C* external corner is made by S2018C* notching and bending the

2000 Base.

BK2015* Tee – For branches at right G2015* angles. Couplings furnished. V2015C*WH2015C*


2"[51mm]

V/G 2000 Series

2"[51mm]

1 5/16"[33mm]

3/4"[19.1mm]

2 7/64"[53mm]

1 29/32"[47mm]

2 11/16"[67mm]

3 22/64"[94mm]

3"[76mm]

1 9/32"[58mm]

1 1/2"[38mm]

2 1/8"[54mm]

1 7/32"[31mm]

How 2009 is used.

3/4"[19.1mm]

Plugmold 2000 extended from wall outlet using 2051H.

2051H fastened to horizontally mountedwall box.

4 1/2"[114mm]

2051H fastened to vertically mounted wall box.

2 1/2"[64mm]Ea. Leg

1 1/2"[38mm]

1 1/2"[38mm]

2017TC

2017TC

2000B

2000B

2017TC used as a corner coupling.

2017TC used as a corner coupling and astraight-through fitting.

Cover gap filler snappedinto place in 2018C.

1 7/8"[48mm]

1 1/2"[38mm]

4"[102mm]

6"[152mm]


Base V/G 2000B-5* 5' [1.5m] .040 SteelCover V/G 2000C* 5' [1.5m] .025 SteelBase & Cover V/G 2000BC* 5' [1.5m] .025 Steel

4

trade size


2409 Ground Clamp – No. 10 ground screw provided. Use with V2400 Series.

V2410A Entrance End – For connecting V2400 with 1/2" trade size conduitand armored cable. Use withV2400 Series.

V2410B Blank End – For closing openend of V2400 Series.

V2410C Entrance End Fitting – Has 1/2"and 3/4" trade size KOs on end and bottom. Additional 1/2" tradesize KO on sides.



2401 Coupling – For joining lengths of raceway. Use with V2400 Series.


V2406 Cover Clip – For covering joint where lengths of cover or base adjoin. Use withV2400 Series (nonmetallic).

2"[51mm]

1 1/2"[38mm]

1"[25mm]


V2089E End Reducing Connector – For connecting V2000 with V500 Raceway through end of V2000.

rectangular KO for extension towall box. Base has #10 threaded

620 2000 Raceway Base andCover Cutter – Portable cutter for 2000 Cover and Base. Tool steel construction for clean and easy square cuts every time. Total manual operation.



BK2048* Single Gang Device Box – G2048* Cover has twistouts for 2000, V2048* V500, and V700 Raceway. WH2048* Base has 1/2" trade KO andS2048* rectangular KO for extension to

wall box. Base has #10 threadedhole for ground connection.

V2048-2 Two-Gang Device Box – Coverhas G2048-2 Twistouts for 2000,V500, and V700 Raceway. Base has 1/2" trade KO and rectangular KO for extension towall box. Base has #10 threadedhole for ground connection.

V2089 Side Reducing Connector – For connecting V2000 with V500Raceway through side of V2000.orange receptacles. Couplings furnished.

V/G 2000 Series (continued)

1/2"[12.7mm]

2"[51mm]

1 5/8"[41mm]

1 3/16"[46mm]

1 3/16"[30mm]

2 7/8"[73mm]

1 3/4"[44mm]

1 3/4"[44mm]

4 5/8"[117mm]

4 3/4"[121mm] 4 3/4"

[121mm]

6"[152mm]

3 1/4"[83mm]

3/4"[19.1mm]

V2400 Series


Base V2400B 5' [1.5m] .040 SteelCover V2400C 5' [1.5m] .040 SteelBase & Cover V2400BC 5' [1.5m] .040 Steel

2 11/16"[68mm]

1 7/8"[48mm]

2 1/8"[54mm]


5


V2489 Side Reducing Connector – For connecting V2400 with V500 Raceway.

V2444 Extra Deep Device Box – V2444-2 Base has rectangular knockout

to enable extension from existing single-gang flush wall box and 1/2" and 1" concentric KOs. V2444 Cover has two twistouts for 500 and 700, and two twistouts for 2400. V2444-2 Cover has four 2400 Series twistouts.

624 2400 and 2400BD Raceway& Cover Cutter – Portable cutter for 2400B and 2400BDRaceway and Cover. Tool steel construction for clean and easy square cuts. Total manual operation.



V2411 90º Flat Elbow – For right angleturns on the same surface (nonmetallic cover).

V2417 Internal Elbow – For making internal corners (nonmetallic cover).

V2417M Internal Elbow – For making internal 90° corners. All steel construction.

V2418 External Elbow – For covering outside corners (nonmetallic cover).

V2451H Back Feed Fitting – For feeding V2400 Raceway from an existing outlet box. Equipped with 1/2" trade size male bushing and locknut washer for grounding.

V2448 Device Box – Cover V2448-2 has one twistout for 2400 on

each side and ends. Base has 1/2" trade KO and rectangular KO for extension to wall box. Base has #10 threaded hole for ground connection.

V2400 Series (continued)

1 5/8"[41mm]

1 5/8"[41mm]


2 3/4"[70mm]

4 3/4"[121mm] 4 3/4"

[121mm]

WL

D

15/16"[23.8mm]

2 1/16"[52mm]

3 7/8"[98mm]


1 3/4"[45mm]

1 29/32"[49mm]

4 1/2"[114mm]

4 1/2"[114mm]

6

GB Series:3-wire, #12 THHN (1 hot,1 neutral and 1 ground),1 circuit; has insulatedgrounding conductor.

GBA Series:4-wire, #12 THHN (2 hot, 1neutral and 1 ground), 2 circuit;outlets wired alternately; hasinsulated grounding conductor.

IG Series:3-wire, #12 THHN (1 hot, 1 neutral and 1 ground), 1 circuit;has insulated-isolated groundingconductor. Orange receptacles.

Wiring Configuration

GB Series:3-wire, #12 THHN (1 hot, 1 neutraland 1 ground), 1 circuit; hasinsulated grounding conductor.

GBA Series:4-wire, #12 THHN (2 hot, 1 neutral and 1 ground), 2 circuit; outlets wired alternately; hasinsulated grounding conductor.

NOTE: SNAPICOIL REELS on custom order. Snapicoil is available on reels if lengths greater than 50’ are needed, or if multiple lengths are required for production-type jobs. The maximum length per reel is 240’ for Snapicoil with outlets 12” and 18” on centers; 500’ with outlets 30” on center. Packaging includes the necessary number of lengths of base, holecut cover, wire clips, and couplings for complete installation. Price and delivery information should be obtained prior to specifying or ordering. To specify or order, add R to the Snapicoil number. Ex: V20GB12R. Other outlet spacings available on custom order.Receptacles are made from high impact thermoplastic. V2000 Plugmold is supplied with two (2) V2010B Blank End Fittings and (1) 2001 Base Coupling. NM2000 Plugmold strips are supplied with two (2) NM2010B Blank End Fittings.

With Snapicoil

CATALOG WIRING OUTLETS (15A 120V NEMA 5-15SR) HOLE CUT COVERNO. LENGTH CONFIG CENTER DISTANCE QUANTITY QUANTITY LENGTH HOUSING

Feet [meters] Inches [mm] Inches [mm]

20GB12 48' [14.63] GB 12" [305mm] 48 Single 8 6' [1.8m] Steel – Ivory, Gray

20GB18 48' [14.63] GB 18" [457mm] 32 Single 8 6' [1.8m] Steel – Ivory, Gray

V20GB30 50' [15.25] GB 30" [760mm] 20 Single 10 5' [1.5m] Steel – Ivory

20GBA12 48' [15.24] GBA 12" [305mm] 48 Single 8 6' [1.8m] Steel – Ivory, Gray

Plugmold with Snapicoil Harness

UNIT OUTLETS CIRCUITCAT NO. LENGTH QUANTITY CORD SET LENGTH TYPE SWITCH BREAKER FINISH

20-C2 3' 4" [1m] 6 Single 6' [1.8m] 12/3 SJT No Yes Steel – Gray, Ivory

Cord-Ended Plugmold Series

NO. OF CONDUCTORS CABLE WIRE SIZE O.D. (40% FILL)TYPE THHN/THWN Inches [mm] V2000 V2400

POWER WIRING 8 AWG 0.216 [5.5] – –WITHOUT DEVICES 10 AWG 0.166 [4.2] – 26

12 AWG 0.130 [3.3] 7* 4114 AWG 0.111 [2.8] 7* 57

POWER WIRING 8 AWG 0.218 [5.5] – 2WITH DEVICES 10 AWG 0.153 [3.9] – 6(PLUGMOLD) 12 AWG 0.122 [3.1] 5* 10

14 AWG 0.105 [2.7] 5* –

Plugmold Wire Fill Capacities for Power

*Wire capacity limited to maximum of seven conductors due to .025" [.6mm] material thickness of cover.**Including one hot, neutral, and ground wire from the receptacle.

7

WIRING OUTLETSCATALOG NO. LENGTH CONFIG CENTER DISTANCE QUANTITY FINISH

Feet [mm] Inches [mm]

20GB206 2' [610mm] GB 6" [152mm] 4 Single 15A Steel – S20GB306 3' [915mm] GB 6" [152mm] 6 Single 15A Steel – WH, BK, V, G, SV24GB306 3' [915mm] GB 6" [152mm] 6 Single 20A Steel – V

24S3612GBX99IV 3' [915mm] GB 12" [305mm] 3 Duplex 20A Steel – V, G

24S3612GBA99IV 3' [915mm] GBA 12" [305mm] 3 Duplex 20A Steel – V, G

20GB506 5' [1.5m] GB 6" [152mm] 10 Single 15A Steel – WH, BK, V, G, S

V24GB506 5' [1.5m] GB 6" [152mm] 10 Single 20A Steel – WH, BK, V, G, S


V24GB512 5' [1.5m] GB 12" [305mm] 5 Single 20A Steel – V

20IG512 5' [1.5m] IG 12" [305mm] 5 Single 15A Steel – V, G

20GBA512 5' [1.5m] GBA 12" [305mm] 5 Single 15A Steel – V, G

V24GBA512 5' [1.5m] GBA 12" [305mm] 5 Single 20A Steel – V

24S6012GBX99IV 5' [1.5m] GB 12" [305mm] 5 Duplex 20A Steel – V, G

24S6012GBA99IV 5' [1.5m] GBA 12" [305mm] 5 Duplex 20A Steel – V, G

24S6012IGX99IV 5' [1.5m] IG 12" [305mm] 5 Duplex 20A Steel – V, G

20GB606 6 [1.8m] GB 6" [152mm] 12 Single 15A Steel – WH, BK, V, G, S

V24GB606 6 [1.8m] GB 6" [152mm] 12 Single 20A Steel – V

20IG606 6 [1.8m] IG 6" [152mm] 12 Single 15A Steel – V, G

20GB609 6 [1.8m] GB 9" [229mm] 8 Single 15A Steel – V, G

20GBA609 6 [1.8m] GBA 9" [229mm] 8 Single 15A Steel – V, G






20GB618 6 [1.8m] GB 18" [457mm] 4 Single 15A Steel – V, G



24S7212GBX99IV 6 [1.8m] GB 12" [305mm] 6 Duplex 20A Steel – V, G

24S7224GBA99IV 6 [1.8m] GBA 24" [608mm] 3 Duplex 20A Steel – V, G



24S7218IGX99IV 6 [1.8m] IG 18" [457mm] 5 Duplex 20A Steel – V, G



24S7212GBA99IV 6 [1.8m] GBA 12" [305mm] 6 Duplex 20A Steel – V, G

24S7218GBA99IV 6' [1.8m] GBA 18" [457mm] 4 Duplex 20A Steel – V, G

Plugmold Multi Outlet Strip

NOTE: “V” indicates Ivory ScuffCoat™ finish, “G” indicates Gray ScuffCoat™ finish, “WH” indicates White enamelfinish, “BK” indicates Black enamel finish, and “S” indicates Stainless Steel finish.













keystone jacks, as well as proprietary solutions from Avaya (Systimax) and NORDX • Modules insert into a wide range of Wiremold Systems • Pre-punched faceplates accept common communication devices

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN

ORT

P&S

OPEN




ED1412 – May 2006 – For latest specs visit www.wiremold.com© Copyright 2006 Wiremold / Legrand All Rights Reserved

Documents

wiremold