POWER &
ENERGY
providing critical solutions to the power industry
3
Finding innovative ways to help the world meet its ever growing demand for
power is a key focus for SPX. As a multi-industry Fortune 500 manufacturer,
we provide creative solutions that serve global energy markets in a myriad
of ways. Our ideas are helping to build more efficient new power plants and
renovate older existing facilities. And, at thousands of power stations in more
than 60 countries across continents, our evaporative and dry cooling solutions
are hard at work. We also supply a wide range of components — from
air preheaters to filter systems for nuclear, coal-fired, combined cycle, solar,
thermal and geothermal power plants.
With operations in over 35 countries, SPX has the global experience and
regional presence, products and powerful ideas it takes to help our customers
compete more effectively, and more efficiently deliver power to almost any
part of the world.
About SPX
4
SCRDeNOx
High Dust
SCRDeNOx
Low Dust(Alternatively)
HPFeedwaterHeater
LPFeedwaterHeater
Gas Gas Heater GGH
• Cooling towers• Air-cooled condensers
• Heat exchanger • Emission control• Service and repair
• System installation tools• System operation maintenance and repair tools
• Medium power transformers• Large power transformers• Step up transformers
SPX products and solutions in a typical coal-fired power plant
SGM - Static Gas MixerESP - Electrostatic PrecipitatorSCR - Selective Catalytic ReductionFGD - Flue Gas DesulphurisationGGH - Gas Gas heater
COAL-FIRED
Cooling Technologies Heat Transfer TechnologiesHydraulic Technologies Transformers
5
• Plate heat exchangers • Control valves
SPX products and solutions in a typical coal-fired power plant
For coal-fired power generation, SPX offers not only an extensive product range for steam cycle cooling
and control, but also decades of experience helping power utilities throughout the world get the most from
their assets. As the world requires cleaner coal-fired power, SPX is at the forefront supplying components
for pollution control, including flue-gas emission control.
• Vertical and side-entry mixers• Cooling water filters• Instrument air dryers• Hydrogen coolant purifiers
Flow Technologies
6
SPX products and solutions in a typical nuclear power plant
NUCLEAR
MSR
Preseparator
“Stand-by” Diesel Engine
Body of Water
Reactor and Steam Generator
HPFeedwaterHeater
LPFeedwaterHeater
• Cooling towers • Moisture separator reheater• Powersep• Feedwater heaters• Turbine condenser• Deaerators
• System installation tools• System operation maintenance and repair tools
• Environmental test chambers• Multi-purpose drying ovens
Cooling Technologies Hydraulic Technologies Thermal Product Solutions Heat Transfer Technologies
7
SPX products and solutions in a typical nuclear power plant
• Centrifugal pumps• Positive displacement gear pumps• Chemical injection systems
• Plate heat exchangers • Cooling water filters• Instrument air dryers• Hydrogen coolant purifiers
• Control valves
As a global company, SPX manufactures critical components for the nuclear power industry, ensuring high
quality products with on-the-ground support around the world. SPX companies have accreditation for major
nuclear standards, including RCCM and ASME® N stamp.
Flow Technologies
8
SPX products and solutions in a typical combined cycle power plant
COMBINED CYCLE
HRSGGas TurbineAir Intake
Oil / Gas
SteamTurbine
HPFeedwaterHeater
LPFeedwaterHeater
• Cooling towers• Air cooled condensers
• System installation tools• System operation maintenance and repair tools
• Environmental test chambers• Multi-purpose drying ovens
• Heat exchanger • Air pollution control• Service and repair
Cooling Technologies Hydraulic Technologies Thermal Product Solutions Heat Transfer Technologies
9
SPX products and solutions in a typical combined cycle power plant
• Air intake and air filters• Fuel gas filters
• Plate heat exchangers • Turbine lubricating oil mist eliminators
• Control valves
For single and combined cycle gas turbines, SPX offers an extensive range of steam cycle cooling and
control equipment. SPX also offers an extensive range of water, gas, oil and air filters to protect the turbine
and the environment.
Flow Technologies
10
Turbine Transformer
Electricity
Air CooledCondenser
SolarReheater
Solar Field
SolarSuperheater
Molten SaltHeat Exchanger
Hot SaltTank
Cold SaltTank
SteamGenerator
SolarPreheater
Expansion Vessel
Deaerator
HPFeedwaterHeater
LPFeedwaterHeater
• Cooling towers• Air-cooled condensers
• Heat exchangers • Steam generator• Deaerator
• System installation tools• System operation maintenance and repair tools
• Environmental test chambers• Multi-purpose drying ovens
SPX products and solutions in a typical solar power plant
SOLAR
Cooling Technologies Hydraulic Technologies Thermal Product Solutions Heat Transfer Technologies
11
• Mixers• Plate heat exchangers
SPX has the execution, experience and expertise to harness the power of the sun. From steam generators
to air cooled condensers, from steam control valves to molten salt mixers, our engineering teams can design
and install the components you need for a successful solar thermal project.
• Control valves• Metering pumps• Process pumps• Lubrication pumps
Flow Technologies
12
SPX is a full-line, multi-service manufacturer of cooling towers, air-cooled
condensers, heat exchangers and thermal components. Our products and
solutions are marketed to coal, nuclear, solar, geothermal, gas and biogas
generation stations.
Project ReferencesOur dry-cooling equipment is installed around the world for a wide range of
environmental conditions: coastal and desert climates, remote industrial and
urban locations and in temperate and freezing climates. We maintain standards
of excellence in power generation and industrial markets and have installations in
some of the most critical power plants in the world.
Air-cooled CondenserChina
Air-cooled CondenserMexico
Air-cooled CondenserChina
Air-cooled CondenserSpain
Air-cooled CondenserUSA
Air-cooled CondenserBahrein
Air Cooled Condensers – Cooling Towers
13
Dry CoolingA-frame Air-cooled Condenser
The most popular style of air-cooled condenser is the modularized A-frame
design, used on power plants of all sizes. Over 800 installations globally.
The integral features are:
• Long-term mechanical and thermal integrity
• Excellent corrosion and freeze resistance
• Low fan-power consumption
• Low maintenance
Hexacool® Air-cooled Condenser
Hexacool is an air-cooled condenser (ACC), well suited for use in smaller
waste-to-energy, biomass and small-size electrical power plants and industrial
cogeneration.
The integral features are:
• Simplified installation procedure with greater degree of prefabrication in
workshop
• Simplified piping and ducting routing layout
• Reduced height for easier integration in urban environment
• Lighter load on foundations
• Decreased wind sensitivity
• Reduced hot-air recirculation
• Easy access for cleaning and maintenance
Indirect Dry Cooling
Indirect dry cooling, couples a dry cooling tower with a steam surface condenser.
This type of system is particularly well suited for large power plants.
The integral features are:
• No fan power consumption (small power consumption in water loop
circulation pump)
• A separated loop for steam and cooling water to avoid contamination or
high water treatment requirements
• Corrosion protection
• Reduced water consumption
• No visible plume
• Reduced noise generation
A-frame Air-cooled CondenserCanada
A-frame Air-cooled CondenserBelgium
Hexacool Air-cooled CondenserGermany
Indirect Dry CoolingSouth Africa
14
Evaporative CoolingNatural Draft Cooling Tower
• Concrete natural draft counterflow tower in varying sizes and configurations
• Efficient and reliable, most commonly used in power generation
• Custom designed for flow rates up to 113,600 m3/hr (500,000 GPM)
• Over 275 natural draft towers installed globally
Counterflow Field-erected Cooling Tower
• Desired for versatility, efficiency and quality for power and industrial facilities
• Customized to meet customers’ exact specifications for performance, structure,
drift and noise level
• Available in pultruded structural fiberglass, wood or concrete
• Tower cells available from 300 to 6900 m3/hr (1,300 to 30,000 GPM)
Crossflow Field-erected Cooling Tower
• Splash-fill cooling towers proven in hundreds of installations over the last
40 years
• Our most versatile tower, with a variety of fill options for heavy industrial use
• Available in pultruded structural fiberglass, wood or concrete, for unsurpassed
quality and reliability
• Tower cells available from 200 to 8000 m3/hr (930 to 35,000 GPM)
MH Fluid Cooler
• Protects process fluids from contamination
• Less fouling and scaling tendencies
• Reduces system energy and maintenance costs
• Conserves valuable space in equipment rooms
• Provides reliable, efficient year-round operation
• Delivers up to 10 percent increased performance over other coolers
Crossflow Cooling Tower
USA
Counterflow Cooling Tower
Mexico
MH Fluid Cooler
China
Natural Draft Cooling Tower
Germany
Air Cooled Condensers – Cooling Towers
15
Project References
Counterflow Cooling TowerPhilippines
Forced Draft Cooling TowerDubai
Counterflow Cooling TowerUSA
Counterflow Cooling TowerUSA
Counterflow Cooling TowerAustralia
Counterflow Cooling TowerSpain
16
Project References
2 x 500 MW ESP ProjectKorea
600 MW Air Preheater ProjectGermany
2 x 800 MW Air Preheater and ESP ProjectGermany
Heat Exchangers – Industrial Air Filters
* Yuba and Ecolaire are brands of SPX Heat Transfer Inc.
*
*
17
NuclearPOWERSEP™
In new or existing nuclear power plants, the POWERSEP high-velocity
separator can be utilized to extend component service life and increase the
electrical output. It is located in the cross-under piping (cold reheat line) in
front of the moisture separator reheater (MSR) and serves as an additional
preseparator.
• Efficient moisture separation
• Simple, compact and robust design
• Easy to retrofit
• Pay-back period less than two years
• Power plant output increased
• Erosion/corrosion problems eliminated
• No additional steam bleeding required
• Long-term references available
• Developed, designed and manufactured by Balcke-Dürr
Moisture Separator Reheaters (MSRs)
• In nuclear power plants, moisture separator reheaters (MSRs) are key
components in the steam cycle of pressurized and boiling water reactors.
MSRs increase the overall efficiency and protect low-pressure turbines from
damage.
• Manufacturer for the first EPR (European Pressurized Water Reactor)
• MSR technology based on decades of experience
• Proven designs for vertical and horizontal MSR configurations
• Fine separators and reheater bundles
Powersep high-velocity separator
Moisture Separator Reheater (MSR)
18
Heat ExchangersGas Gas Heater (GGH) Rotor System
• Decades of experience in engineering, manufacturing and service
• Various profiles of heating elements characterized by high heat transfer rate,
low flow resistance and low maintenance requirement
• Custom designed double sealing system with massive seal plates, readjustable
during operation, highly efficient, durable, leakage rate less than 0.5 percent
• Enamelled heating elements for corrosion resistance
• Custom designed center column support, for less steel consumption
(up to 10 percent) compared to conventional beam support
• Swivel-type soot blower for high-pressure and low-pressure cleaning
in a space-saving design
Air Preheater (Rotor Type)
• More than 70 years of experience in engineering, manufacturing and service,
with project reference that include the installation of one of the world’s largest
air preheaters (21 meter diameter and 1,250 ton rotating mass)
• Compact rotary heat exchanger for utility, captive power plant and industrial
applications
• Custom-designed sealing systems
• Capability of reengineering and modernizing rotary air heater for fuel saving
and CO2 reduction for power plant upgrades
Heating Elements
• Custom designed
• Low plugging tendency and low pressure resistance
• High heat transfer rate
• Easy-to-clean surface
• Resistant to corrosion, filth and erosion
• Patented enameling process for long lifetime under severe industrial conditions
• Temperature-shock resistance
• Basket arrangement for fast and easy replacement
• Adjustable plate thickness to withstand flue gas erosion
Air Preheater
Heating Elements
Gas Gas Heater
Heat Exchangers – Industrial Air Filters
19
Feedwater Heater
• A global supplier with a wide range of feedwater heaters
• Over 90 years of experience in engineering, manufacturing and service
• More than 1,200 references for header-type high-pressure heaters
• Custom-designed constructions such as U-tube or straight-tube duplex heaters
Deaerator
• Essential for removing gases in steam power plants, where excessive dissolved
gases from the feedwater heating circuit cause boiler corrosion problems
• Specializing in nuclear and conventional large-scale power plants
• Tray-type or spray-type deaerators in combination with heaters
• Proprietary sprayer design
Turbine Condenser
• More than 100 years of experience in engineering and manufacturing
• Equipping power plants with capacities exceeding 1,400 MW
• Patented TEPEE tube bundle with performance-optimized design
• Increase output in existing power plants through rebundling
• Capable of system optimization for power plant upgrades
Industrial FiltersElectrostatic Precipitator (ESP) and Baghouses
• ESP efficiency exceeding 99.8 percent
• Compact design utilizing large plate spacing
• Best available technology for optimized flue gas path
• More than 3,000 installations worldwide in power and industrial applications
• Bi-Corona® technology available to meet fine-particle requirements 2.5 mg/L
• New twin valve cleaning system for optimum cleaning efficiency of filter bags
• AESM (Advanced Energy Saving Management) technology for controlled
cleaning pressure
Bi-Corona® Electrostatic Precipitator
Feedwater Heater
Deaerator / Feedwater Tank
Turbine Condenser
20
SPX offers an extensive portfolio of plate heat exchangers covering many power
station applications. Regularly SPX heat exchangers replace older technology
products due to the simplicity of installation and their high performance thermal
characteristics. SPX Plate Heat Exchangers can be used in many power plant
designs, including nuclear, coal and solar.
Primary Applications for Power Stations
Heat transfer duties for:
• Nuclear and conventional power stations
• Peak load stations
• Combined heat and power stations
• Geothermal schemes
• District heating
Project References
Lube Oil CoolerChina
Hybrid PHEChina
PHE for Central CoolingChina
Plate Heat Exchangers
21
Plate Heat ExchangersSPX plate heat exchangers (PHEs) offer solutions for heat transfer applications
in the power industry that historically were served by shell-and-tube technology.
Plate heat exchangers play an increasingly important role in helping power
producers meet stringent water environmental and energy conservation
regulations. Whether recovering waste heat or isolating the cooling system from
the cooling source, SPX has the application knowledge and products to improve
efficiency and performance. Advances in PHE technology have helped it become
the technology of choice in this demanding industry.
Powerful Benefits
• Protects equipment from damage caused by contaminants
• Highly efficient heat recovery
• Flow rates up to 4,500 m3/hr (20,000 GPM)
• Simplifies maintenance process to save time and cost
• Modular design to provide flexibility for reconfiguration
• Compact design to save space
Efficiency
• High thermal efficiency saves money through reduction in required heat
transfer area
• Low liquid hold-up improves start-up time and reduces operating fluid costs
• Up to 97 percent heat recovery can be achieved
Maintenance
• Eliminates complicated maintenance, such as x-ray, ultrasonic and other
nondestructive test procedures
• 100 percent corrosion-resistant material reduces inspection and maintenance
requirements while ensuring reliable operation
• Lack of moving parts minimizes vibration, ensures reliable operation and
reduces maintenance
Cost
• Lower capital costs compared to traditional shell-and-tube technology
• Reduced weight
• Reduced life-cycle cost
• Reduced fouling, for higher thermal efficiency and lower maintenance and
operating costs
• Lower fluid velocity for maximized plate life and reduced maintenance
Plate Heat Exchangers
Custom Hybrid Heat Exchangers
Standardized Hybrid Heat Exchangers
22
SPX develops solutions for applications found in the general industrial, oil and
gas, power generation and pulp and paper industries. Valve products include
globe, control, gate, butterfly, ball and surge relief valves.
Control and Isolation ValvesSPX provides a wide range of valves for the control of pressure, temperature and
flow-induced noise in all types of power plants. Products include severe service
and general service control valves, variable orifice desuperheaters, Raven™ trim
and steam-conditioning valves and nuclear control valves, as well as custom-
designed specialty valves.
These Projects Feature
• Multiple types of body and bonnet styles
• Sizes from 0.75" to 24"
• Pressure class: 150 – 4500
• Available in carbon steel, chrome moly, stainless steel and forged equivalents
• Certified to ISO 9001, ASME Sections I and III and Pressure Equipment
Directives (PED 97/23/EC)
Valves
Variable Orifice Desuperheater Control Valve Pneumatic Diaphragm Actuator Desuperheater
23
Taishan Power PlantChina
Castle Peak Power StationHong Kong
Gaozi Power Plant China
Project References
Nuclear Control ValvesSPX has engineered and manufactured valves for the nuclear industry for over
40 years under the Copes-Vulcan® brand. Products include globe, gate, swing,
check, butterfly, ball and sampling valves for nuclear customers, and are all
ASME Section III “N” and “NPT” Stamp certified.
Nuclear Applications Include
• Feedwater
• Steam dump
• Pressurizer spray
• Reactor coolant
• Sampling
• Service water
• Safety injection
• Power-operated relief
Global SupplierIn 2009, SPX reached an agreement with a nuclear equipment manufacturer
to provide highly specialized squib valves for up to twelve new nuclear power
stations in the United States and China.
SPX has supplied valves to Japan, China, South Korea, the United States, Canada,
Mexico, Switzerland, United Kingdom, Brazil and more.
Copes-Vulcan Valves for
• Boiling water reactor (BWR)
• Heavy water reactor (CANDU)
• Pressurized water reactor (PWR)
Butterfly Ball
Swing Check
Globe Globe
Gate
24
PumpsSPX provides a wide range of pumps for transporting and metering
liquids in power plants.
Pump types
• Diaphragm pumps
• Plunger pumps
• Screw pumps
• Vane pumps
• Heavy-duty centrifugal pumps
• Internal gear pumps
Liquids Handled
• Toxic or chemically aggressive liquids
• Slurries and suspensions with
particle sizes up to 100 mm
• High-and-low viscosity liquids
• Long service life of diaphragm in
pumps with remote alarm to
signal failure
Benefits
• High volumetric efficiency
• Low vibration, low noise
• High reliability
• Low running cost, easy maintenance
• Long lifetime
• Custom designs
Twinro Bunkering Pump
Novaplex Process Pump
Triro Low-pressure Pump
Novados Metering Pump
Vane Pump
Multistage Centrifugal Pump
Pumps – Chemical Injection
Positive Displacement Gear Pump
• Nuclear design RCCM3 volume E
• Lubrication system and fuel feeding for
diesel engine in nuclear power plants
Centrifugal Pump
• Nuclear design RCCM3 volume E
• Cooling system for diesel
engine in nuclear power plants
25
Measuring InstrumentsSPX provides on-line measurement for the continuous supervision of silica
concentration in boiler feedwater or during water treatment.
Advantages
• Fully automatic operation with remote maintenance and network ability
• Minimum operating cost due to small reagent consumption
• Connection of up to 100 external physical-measurement sensors
• Easy to read interface with interactive touchscreen operationPowerMon
Chemical Injection SystemsSPX provides turnkey metered blending systems for the treatment of boiler
feedwater in all types of power plants.
Advantages
• Cost savings by automatically adjusting treatment based on water analysis
• Safety and protection against hazardous chemicals for operators and
surroundings
• Remote operation with automatic stroke control of pumps
• Long service life of diaphragm pumps with remote alarm for failure
• Can add heads for future injection points
• Can add variable-speed motor or stroke control for automatic injection in
proportion to the main flow
Boa Steel Power PlantChina
Zhenhai Power PlantChina
Qinshan Project China
Lingao Project China
Project References
26
SPX manufactures filters, products and systems to remove moisture and
contaminants from air, gas, fuel, lubricating oil and insulating fluids.
Strainers and FiltersSPX offers a range of industrial filtration solutions for multiple process industries
worldwide. Products include simplex and duplex cast and fabricated strainers,
self-cleaning and back-flushing strainers, high-pressure gas filters and fabricated
bathtub strainers. These products provide protection for pumps, plate heat
exchangers, lube oil, bearing cooling and bearing lubrication.
The Filters’ Design Features Include
• A wide variety of materials and design codes
• Standard designs available for a variety of process applications
• Custom designs to meet customers’ specific operating conditions and
parameters
• Easy maintenance to ensure continuous operations
• Fine mesh inserts capable of removing particles down to 10 microns for liquids
and one micron for gas
• Compliant to all PED 97/23/EC
Filter Basket and T-type Strainer
Simplex Filter and Duplex Filter
Strainers – Filters
27
Air Intakes and FiltersSPX manufactures standard air intake filter systems for gas turbines and
turbo compressors with capacities which can exceed 600 m3/s (21,200 cfs)
and different transition styles up to 30 sq m (320 sq ft). Disposable filter
elements are also manufactured conforming to ASHRAE™, EN and ARAMCO™
specifications. Customer engineered air intake systems are available for
applications in hostile environments, including acid gas removal.
Fuel Oil, Fuel Gas and Lubricating Oil FiltersWell known for high performance and quality, many of our gas and oil filters are
specified as standard on original equipment by gas turbine, diesel and gas engine
manufacturers.
• Simple to service
• Disposable filter cartridge
• Suitable for engine or floor mounting
• Duplex units with transflow changeover valve available
Lubricating Oil Mist EliminatorsOil mist eliminators are designed to extract oil mist droplets and return them to
the gas turbine lubricating system, removing health, safety and environmental
concerns.
• No user intervention required apart from periodic cartridge changes
• Few, robust components to help ensure smooth operation and long lifetime
• No visible plume and concentrations of less than 5 mg/L on clean side of the filter
Fuel and Lubricating Oil Filters
Lubricating Oil Mist Eliminators
Fuel Gas Filter
28
MixersWith over 85 years experience in mixing technology, process knowledge and
technological innovation, the SPX Lightnin® brand manufactures durable, long-
lasting mixers, agitators, aerators and flocculators for fluid processing systems,
FGD applications and molten salt mixing globally.
Top-Entry Mixers
There are three types of top entry mixers for the power industry. They are built to
handle the severe duty of solids suspension and re-suspension, blending and gas
dispersion.
• Series 10 — smaller vessels, sumps, solids suspension and re-suspension
• 70/80 Series — FGD Process Mixers (limestone, gypsum slurries)
• 700/800 Series — large storage tanks and absorber agitators
VSF Side-entry Mixers
Side-entry mixers specially designed for flue gas desulphurisation (FGD), the
pollution control system in power plants.
• Mechanical seal designed to excel in a harsh FGD environment. Engineered to
operate with no outside flush liquid
• Seal shutoff to provide maintenance on unit while absorber is in operation
• A-312 hydrofoil impeller is specifically designed to produce the most flow per
power to suspend solids while dispersing oxidation air
High-efficiency Impellers
• Hydrofoil impellers for top and side entry applications
• Can reduce power requirements by up to 50 percent
• Delivers operating cost savings while maintaining performance.
• Reduces required capital cost for desired performance
SX Impeller
SPX offers the only corrosion-resistant resin system that incorporates high
efficiency operation. For use in corrosive slurries, the SX system costs the same
as rubber-covered steel, while providing a more robust and efficient design that
eliminates the possibility of lining failure. The SX system is:
• More efficient than any metal impellers
• Inherently corrosion resistant (Derakane® 470 resin)
• Less weight for easier installation
• Comparable in cost to rubber-covered steel
Top-entry Mixers
VSF Side-entry Mixer
High-efficiency Impellers
Mixers
29
Air and Gas Dryers
DryersInstrument Air Dryers
SPX provides compressed-air dryers and filters that remove oil, water, dirt, rust
and pipe scale. Contaminants found in compressed air can adversely affect
all components of an air-distribution system, and can cause a malfunction of
pneumatic control in the instrument air system. Properly treated compressed air
can improve work efficiency and reduces maintenance. SPX desiccant dryers
incorporate these quality features:
• Highly hygroscopic desiccants combine spherical uniformity with superior
crush strength to deliver stable dew point performance and low dust creation
• High quality process switching valves deliver consistent repeatability to ensure
system integrity and long component life cycles
• Precision timing circuits control process valve sequencing protocols to deliver
optimum dew point stability and energy efficiency
• Calculated desiccant bed construction ensures ideal tower velocities to absorb
moisture, stabilize dew points and prevent bed movement
• Spare mufflers included on all models and sizes
Hydrogen Coolant Purifier (HCP)
The HCP is a self-contained system that dries and purifies hydrogen gas used
as a coolant in electrical power plant generators. It removes water, oil and other
contaminants that cause corrosion and cracking in retaining and zone rings, and
reduces lead carbonate formation, increased windage losses and other potentially
catastrophic consequences.
• Activated carbon bed
• DE-32 molecular sieve desiccant dryer
• Removes hydrocarbons and water vapor
• High-efficiency hydrogen gas heavy-duty magnetic-drive blower
• Helps maximize generator output
Instrument Air Dryers
Hydrogen Coolant Purifier
Daharki Combined Cycle Power PlantPakistan
Glow 115 MW CFB3 Project Thailand
Sidi Krir and El Atf Combined Cycle Power PlantEgypt
Project References
30
SPX is a global supplier of high-force, high-performance hydraulic and pneumatic
products and systems.
High-pressure Hydraulic Tools and EquipmentSPX is a global leader providing professional hydraulic tools and equipment to
global customers in the power industries, such as wind power, nuclear power and
coal-fired power. Marketed under the Power Team® brand, the product range
includes high-quality hydraulic tools, such as cylinders, pumps, pullers and torque
wrenches that are used to install and maintain power systems. ISO 9001:2000
certified and backed by the Marathon Lifetime Warranty, technical support and
service network.
Hydraulic and Pneumatic Tools
Hydraulic Cylinders
• General and special-use
cylinders
• Size 2 to 1,220 tons
Hydraulic Pumps
• Manual pumps
• Powered pumps
Hydraulic Tools
• Hydraulic torque tools
• Hydraulic presses
• Flange spreaders
• Nut splitters
• Bearing pushers/pullers
• Post-tensioning jacks
Rugged Pullers
• Mechanical — up to 30 tons
• Hydraulic — up to 100 tons
Wide Range of Jacks
• Post tensioning
• Portable high-tonnage
• Inflatable
• Bottle
• Toe
• Sidewinder
• Up to 150 tons capacity
• Up to 45 cm (18") stroke
Main Applications in Power Industries
• Steam turbine installation and deviation
correction
• Open and installation of steam
turbine cover
• Disassembly of corrosion or thread-damaged
bolts in pipe flanges and fans
• Bearing disassembly in high-power
generating sets
• Bolting applications with high-torque
requirements
• Lifting of huge coal pulverizer
• Heavy-equipment installation and maintenance
• Wind-power tower installation and
maintenance
31
SPX develops and manufactures microprocessor-based, controlled-temperature
laboratory ovens and furnaces and thermal product and test solution equipment to
simulate or condition environments.
Environmental Test ChamberSPX, through TPS, designs and manufactures environmental chambers, ovens
and thermal products for testing, validating or storing customer samples under a
variety of climatic conditions. Its custom-designed environmental test chambers
and ovens can serve the needs of large-scale conventional power plants, nuclear
power stations, wind farms and other types of power generation plants.
Environmental Test Chamber (ETCU) Ultimate Series
• Used for testing nuclear power materials
• Temperature range: –70° to 200°C (-95° to 390°F)
• Humidity as low as 5 percent
Walk-in Test Chamber (ETR)
• Used for testing outdoor equipment for all kinds of power plants
• Temperature range: –70° to 100°C (-95° to 210°F)
• Humidity range: 25 percent RH to 98 percent RH
• Customized interior dimensions
High-Low Temperature Thermal and Humidity Test Chamber (TC)
• Used for testing outdoor equipment of all kinds for power plants
• Temperature range: –70° to 150°C (-95° to 300°F)
• Humidity range: 20 percent RH to 98 percent RH
• Interior volume: 100 to 1,000 L (3.5 to 35 ft3)
Multi-purpose Drying Oven (LO/TDG)
• Used for drying and solidifying materials or components for power plants
• Temperature range: 20° to 300°C (70° to 570°F)
Test Chambers and Ovens
Environmental Test Chamber (ETCU)
Walk-In Test Chamber (ETR)
High-Low Temperature Thermal and Humidity Test Chamber (TC)
Multi-purpose Drying Oven (TDG)
32
SPX is a global leader in obstruction lighting and a major supplier of remote
asset-monitoring solutions for managing critical applications. The company
provides specialized obstruction lighting products to serve the wind energy,
telecommunications, and utilities markets through its Flash Technology® division.
• Flash Technology’s FTB 360i LED lighting solution was specifically
designed to meet the wind energy market’s requirements for superior
obstruction lighting.
• The FTB204 high-intensity obstruction light is engineered for large scale
power plant facilities where highly conspicuous marking is required.
• The FTB 324 dual-strobe obstruction light is a cost-effective workhorse
solution that has proven durability and can be seen on over 15K structures
worldwide.
• The FTS 362 Advanced LED Solution incorporates the latest developments in
LED technology and advanced control systems. It is the newest member of the
Flash Technology lighting portfolio.
FTB 360i
FTB 204
FTB 324
FTS 3620 Advanced LED Solution
Lighting and Monitoring Equipment
33
In addition to power generation, SPX solutions help distribution networks bring power to businesses and households.
Power Distribution
34
SPX manufactures power transformers and transformer accessories under the
Waukesha® brand while also providing complete transformer service solutions for
the transmission and distribution of electric power.
Medium Power Transformers / Step Up TransformersPower transformers ranging from 10 to 100 MVA in primary voltages
through 345 kV
• Substation transformers
- Single- and three-phase
- Two and three windings
- Optional load tap changer
- Series parallel reconnectable
• GSU (generator step-up) transformers
• Unit Auxiliary Transformers
• Station service /start-up transformers
• Auto transformers (three-phase or single-phase)
• Zig-zag grounding transformers
• Special-duty transformers (motor starting, low impedance,
pulse loading etc.)
• FR3 natural ester fluid-filled transformers (new units or field retrofill)
• Three-phase voltage regulators (new units or field retrofill)
Large Power TransformersPower transformers ranging from 100 to 1200 MVA in primary
voltages through 500 kV
• LS-Large single-phase (all types)
• LT-Non-load tap-changing three-phase (all types)
• LTC-load tap-changing three-phase
• LTC-AUTO-on-load tap-changing autotransformers
• LT-AUTO-non-load tap-changing autotransformers
Waukesha transformers are synonymous with quality and reliability and are
manufactured at the company’s state-of-the-art transformer plants in Waukesha,
WI and Goldsboro, NC. All Waukesha transformers are designed, manufactured
and tested in accordance with the latest standards of IEEE™, ANSI™ and NEMA™
and the quality standards of ANSI/ASQC 9001 and ISO 9001: 2008.
420 MVA top-rated, 345 kV autotransformer is ready for test in Waukesha’s manufacturing facility
Transformers – Dielectric Fluids – Filtration Systems
35
In addition to quality and reliability, Waukesha currently leads the world’s power
transformer industry in the resolution of issues related to applying FR3 fluid in
medium and large power transformers. Waukesha has done a variety of tests to
understand how to use natural ester fluid in larger transformers. Waukesha has
built more new power transformers and retrofilled more existing units with FR3
than any other manufacturer on record.
Natural Ester Fluids / Envirotemp™ FR3™ FluidEnvirotemp FR3 fluid is a patented, biodegradable, seed-based dielectric fluid
designed by Cooper Power Systems. Made from a formulation that includes
vegetable oils, FR3 fluid has been proven to add value to new and retrofilled power
equipment.
Main Benefits
• Environmental biodegradability
In conjunction with recognized testing organizations, the U.S. Environmental
Protection Agency (EPS) created the Environmental Technology Verification
(ETV) Program to further environmental protection by accelerating the
acceptance and use of innovative, improved and more cost-effective
technologies. By objectively and systematically documenting the performance
of commercial-ready environmental technologies, the ETV program assists and
informs those in need of credible data before utilizing a new technology.
• Fire safety
This benefit comes from having an exceptionally high fire point (360°C).
Because of this, FR3 fluid is listed as a Less-Flammable Dielectric Liquid by
Factory Mutual and Underwriters Laboratories for use in complying with the
National Electric Code™ (NEC) and insurance requirements.
• Slows the aging rate of cellulose insulation versus the same material in mineral
oil tests conducted by the developer, indicating a dramatic increase in cellulose
insulation life.
• Dramatically smaller carbon footprint than traditional mineral oil. According
to calculations made by the National Institute of Standards and Technology
(NIST) using their B.E.E.S. calculator, natural esters have less than two percent
of the carbon footprint of mineral oil.
Insulating Oil Treatment
Vokes® Streamline™ is a high-efficiency insulating oil filtration system that returns
the oil to a high level of dielectric strength.
• Removes particles, including fibers, rust and colloidal carbon
• Eliminates free and dissolved water Streamline
36
CENTERS OF EXCELLENCE
AmericasBrazilSao Paulo
CanadaBrockville, ON
USABethlehem, PABrea, CABridgewater, NJCanonsburg, PACharlotte, NCDelevan, WIGoldsboro, NCHouston, TXKansas City, MOMcKean, PAOcala, FLOlathe, KSOverland Park, KSRochester, NYTulsa, OK
EMEABelgiumBrussels
DenmarkKolding
GermanyMoersNeubeckumNorderstedtRatingenWenden
HungaryBudapest
IrelandKillarney
NetherlandsAssenEtten-Leur
South AfricaKelvinMidrandNigel
UAEDubai
UKGlasgowMacclesfieldNewburyWinsfordWorcester
APACAustraliaHomebush
ChinaBeijingGuangdongGuangzhouHebeiJiangsuShanghaiSichuanTianjin
IndiaAhmedabadJaipur
KoreaBusan
MalaysiaDamansara
New ZealandAuckland
Singapore
Manufacturing and Technical Facilities
37
AmericasBrazilSao Paulo
CanadaBrockville, ON
USABethlehem, PABrea, CABridgewater, NJCanonsburg, PACharlotte, NCDelevan, WIGoldsboro, NCHouston, TXKansas City, MOMcKean, PAOcala, FLOlathe, KSOverland Park, KSRochester, NYTulsa, OK
EMEABelgiumBrussels
DenmarkKolding
GermanyMoersNeubeckumNorderstedtRatingenWenden
HungaryBudapest
IrelandKillarney
NetherlandsAssenEtten-Leur
South AfricaKelvinMidrandNigel
UAEDubai
UKGlasgowMacclesfieldNewburyWinsfordWorcester
APACAustraliaHomebush
ChinaBeijingGuangdongGuangzhouHebeiJiangsuShanghaiSichuanTianjin
IndiaAhmedabadJaipur
KoreaBusan
MalaysiaDamansara
New ZealandAuckland
Singapore
38
ISO 9001
ISO PED Category III
ASME
• section I, S Stamp
• section III, N and NPT Stamp Class 1, 2 and 3
• section III, NCA 4000
• section VIII
API 598
ANSI
• B 16.34
• NQA 1
• N 45.2
• B 31.1
CSA 2 2999.38Z299.4
MSS SP61
MIL
• 145208A
• Q9858
• STD2132
10CFR 50 Appendix B
NAVSHIPS
• 250-1500-1
Qualification Standards
39
SPX
13515 BALLANTYNE CORPORATE PLACECHARLOTTE, NORTH CAROLINA 28277
Tel | 704 | 752 | 4400Fax | 704 | 752 | 4505
www.spx.com
©2010 SPX CORPORATIONa4_SPXpower-10A