Download pdf - Quickie Implement Leaflet

Quic

ke imple

ments

22 | Quicke Dimension

A

b

c

THE LOADER CANNOT FUNCTION WITHOUT IMPLEMENTS. Every day, all year round, Quicke loaders carry out work duties for many different users, from farmers to contractors. Without good-quality, versatile implements, the loaders would not be as useful. This is why we invest considerable resources in devel-oping implements that do the Quicke loaders justice. This investment and effort has resulted in us also being the world’s largest producer of implements for front loaders.

Implement hooks for various loaders

A: EuroEuro implement hooks (Ø 40 mm) are the most widely used hook type.

As a result, owners of many different loader makes can also benefit from our

large implement range.

B: SMS (Svensk Maskin Standard) These implement hooks (Ø 60 mm) are primarily adapted for Trima’s front loaders.

If a Quicke loader is equipped with a Combi implement subframe Euro/SMS,

it can work with both Euro and SMS implements.

C: Quicke type 3 These implement hooks (Ø 25 mm) have only been used on older

Ålö loaders (up to 1992) with the Quicke type 3 toolcarrier. If a new Quicke

loader is equipped with a Combi implement subframe Euro/Type 3,

it can work with both Euro implements and with the older type 3 implements.

We can also provide a selection of adapters for other hook systems.

Quicke Dimension | 23

THE LOADER CANNOT FUNCTION WITHOUT IMPLEMENTS.

Quadrogrip®

bale implement Flexibal®

Flexibal

weight 195 kg

Bale size max. 180 cm

Bale support

weight 45 kg

Quadrogrip is the best implement on the market for handling wrapped square

and round bales. The implement arms are seated on 350 mm wide, extremely

stable sliding plates, which move along the main frame. When stacking, it is

possible to lock either the right or left arm, which makes for easier work. The

sliding rails are replaceable and made of high-quality polyethylene, which does

not require lubrication. These sliding surfaces are also vertical so that dirt can-

not become trapped. This results in reduced friction, almost silent arm move-

ments, minimal wear and a long service life.

Three implements in oneFlexibal is a strong and very versatile implement. The 125 mm thick, rotating steel tubes are mounted on two powerful

stone fork tines. The steel tubes are hydraulically adjustable sideways. When the bale is handled, the steel tubes roll care-

fully in under the bale. The tubes’ generous length and diameter distribute the pressure evenly over the bale. When straw

or hay bales are to be transported, the steel tubes can be dismantled quickly and easily. With the tubes removed, Flexibal

can also be used for pallet handling (max. 1,000 kg).

As an option Flexibal can be equipped with an adjustable bale support that is installed on the back of the implement.

This provides the potential to either handle larger bales or to stack bales on their ends.

Selecto F

ix – Easier implemen

t changes

Selecto F


t changes

Quadrogrip 200

Total width 235 cm

For bale size, min-max 60-200 cm

Arm length 130 cm

Weight 418 kg


Flexigrip™ Unigrip™

Grip, lift and turn the bale. Then transport it to the storage place, where stacking to at least the height of three bales is a simple matter.

Select the best equipmentSilaging in plastic bales can produce first-class silage.

However, the bottleneck in this process is often the

implement that has to handle and transport the

bales. It is therefore important to select a quality

product that can handle the bales in the right way. If

the implement is not good enough, it can break or

damages the bale plastic and the whole process stops,

expensive equipment and manpower are at a stand-

still and the quality of the silage is impaired.

Our implements are characterised by powerful

bearings in the arms, large implement areas so that

the pressure is distributed optimally and by the to-

tal absence of any sharp edges. We accept no com-

promises – the quality has to be the very best.

Unigrip 130 160

For bale sizes, min-max 90-130 cm 120-160 cm

weight 200 kg 240 kg

Storing the bales upright on top of each other reduces the risk of air and

moisture penetrating into the bales.

The implement arms are housed in powerful hinged points with replace-

able bushings. Both the right or left arm can be locked Independently, but

there is still some mobility, making it possible to stack the bales tightly

without damaging the plastic. In addition, the implement arms are designed

so that it is easy to reverse out from the bale, and this is also an advantage

when the bales are to be stacked tightly.

The uniquely curved, rounded shape together with the 90 mm thick

tubes contribute greatly to the very careful handling of both vertical and

horizontal bales. Note in particular the long, curved tubes, curved in one

piece with no sharp edges or welded joints. The upper tube extension is a

Quicke speciality that provides significantly better support when the bales

are handled horizontally.

Unigrip has a tested and proven design and a low net weight. It carries

out the same tasks as Flexigrip. The choice between these two implements

depends on the individual user’s work routines. Unigrip is also well suited

for smaller square bales (80 x 80 – 130-160 cm).

The implement arms distribute the pressure evenly over a large area,

and this ensures careful handling of the bales. The tubes on the arms have

a powerfully dimensioned diameter. Unigrip also has a large tube diameter

and no sharp edges, so that the plastic around the bale is not damaged.

Flexigrip 160 200For bale sizes, min.max. 120-160 cm 150-200 cm

Weight 242 kg 262 kg

Selecto F


t changes

Selecto F


t changes

bale implement


Selecto F


t changes

Silosplit®

DB 2115 Weight 200 kg

Increased lifting height 115 cm

Number of bales 4-5

[bale height 120 cm]

Bale size max. 130 cm

For safe handling of 2-4 bales.The bales are securely held between the tines and the upper section. In other words,

there is no risk of dropping the bales during transport or stacking. The mast is both

telescopic and hydraulic. The height of the upper section can vary from 95 cm to

195 cm.

Equip your front loader with 115 cm extra lifting height, so that you

can stack the bales even higher. The DB 2115 is an excellent imple-

ment, particularly for those who require

a high lifting height with short, manoeu-

vrable loaders.

DB 4000

DB 4000 Weight 190 kg

Number of tines 4

DB 2115

Selecto F


t changes

Silosplit m hd weight 85 kg 110 kg

Width 120 cm 120 cm

Length 140 cm 170 cm

PATENT

Split the bale with ease and cheaplyUntil now, splitting bales has entailed hard work or considerable expense. If you have a loader with

dual-action lifting cylinders, you can solve the problem thanks to Silosplit.

Silosplit can both transport and split bales. When you have placed the bale where it is to be split,

you place the blade across the top of the bale and press down. Both straw and silage bales fall apart in

two pieces, simply and smoothly without complicated extra hydraulics. It is then easy to handle the

material. Silosplit is supplied with an easy-to-use blade guard to provide protection from the sharp

cutting edge.

Silosplit is naturally patented.


Bale implement

Square Bale Fork – Safety

Square Bale Fork – standard

The bale spike is particularly well suited to handling round bales. The

longer tine ensures safe transport of the bale. The shorter tine prevents

the bale from wobbling and rotating during stacking.

The Square Bale Fork is a simple, robust implement for both round

and square bales. The tines in the box section can be installed with

a separation of 80 or 130 cm. As an optional extra, the fork can be

supplied with a U-shaped vertical rear

extension, which helps to support the

top bale.

The Square Bale Fork’sfolding box section is a new and valuable safety detail.

Firstly you can lock the tines in the upright position, increasing safety during transport,

particularly on public roads. Secondly you get more efficient and safer handling.

When unloading, the bales are pushed into place by the main frame. If unloading takes

place at full height, the top bale is pushed into place with the aid of the upper section

of the implement, without the long tines being pressed down into the bales. As a result,

there is no risk of the bales falling back when you reverse.

The Square Bale Fork can be supplied with two different frames. The 190 cm frame

is suitable for long, large bales. The 140 cm frame is

supplied with two tines as standard, although this

number can be increased to a total of five.

As optional extra equipment, the Square Bale Forks

can be supplied with a back extension (for handling

more bales) or a bag lifter (for handling large bags).

Square Bale Fork Bale spike

Bale spike

Weight 60 kg

Width 115 cm

Tine length 125 cm

Square Bale Fork – Safety 140 190


Width 140 cm 190 cm

Number of tines, standard 2 5

Tine length 125 cm 125 cm

Square Bale Fork - standard Weight 78 kg

Width 140 cm

number of tines, standard 2

Tine length 82 cm or

125 cm

Extension Weight 42 kg

7


Silograb®

silage Multibenne™

The perfect all-round implementIf you have a diet feeder that is to be loaded with various feeds, Multibenne is the best

choice. The wishes and requirements to which we have paid particular attention are that:

It should be perfectly suited for its purpose – namely silage handling. The side

ends are therefore tapered so that they can be inserted into the silage more easily.

When the implement is tipped backwards, the high ends come into play, so that loose

material is not lost. A relatively short base makes it easier to fill the entire bucket, all

the way in to the back. The centre of gravity thereby moves closer to the tractor, and

when unloading into high-sided vehicles, the bucket tip does not protrude as far into

the vehicle. The closed bottom and the close tine location results in reduced spillage.

With the closed bucket bottom, you can always completely gather up the material.

Multibenne, which is designed according to the same principles as Silograb, can

handle many different types of fodder, as well as manure. As a result, it is not neces-

sary to switch between implements when feeding.

Silograb is an extremely versatile implement. The close tine distribution almost eliminates the spillage of silage.

The tines are mounted in a specially hardened box section (approximately six times larger than standard profiles),

which does not turn or deform under load. The tines follow a circular movement through the material, which pro-

duces the cleanest cut, the least power consumption and the longest service life for the tines. In addition the material

is pressed against the back of the implement when the tines are lowered, and this means that the silage remains in

place, even when driving over uneven terrain.

All models have two hydraulic cylinders. On the large models, the cylinders are 15% larger. The 210 to 250 models

are supplied with a mesh construction in the upper section.

Silograb 130 150 170 190 210 230 250 Weight 250 kg 270 kg 300 kg 320 kg 355 kg 377 kg 405 kg

Width 130 cm 150 cm 170 cm 190 cm 210 cm 230 cm 250 cm

Volume 0.69 m3 0.79 m3 0.90 m3 1.01 m3 1.11 m3 1.22 m3 1.33 m3

Depth 85 cm 85 cm 85 cm 85 cm 85 cm 85 cm 85 cm Number of tines

in the fork 7+7 8+8 9+9 10+10 11+11 12+12 13+13

Multibenne 130 150 170 190 210 230 250 Weight 280 kg 304 kg 360 kg 386 kg 423 kg 447 kg 477 kg

Width 130 cm 150 cm 170 cm 190 cm 210 cm 230 cm 250 cm

Volume 0.66 m3 0.76 m3 0.86 m3 0.96 m3 1.07 m3 1.17 m3 1.27 m3

Depth 80 cm 80 cm 80 cm 80 cm 80 cm 80 cm 80 cm

Number of tines in the fork 7 8 9 10 11 12 13

Selecto F


t changes


Multigrab hd™ Manure forkMaxi Grapple™

The bucket is based on the powerful, reinforced HD bucket. The grapple

arm is installed on the rear of the bucket, which also contributes to the im-

plement’s strength. The movable, profile-pressed upper section is supplied

with strong bearings, three-layer bushings and large pivot pins with stable

locking. The section with the powerful Hardox teeth is bolted in place. Stress

and torsion forces are thereby transmitted to the entire construction. The

teeth (version T) are simply bolted in place with a bolt in the bucket bottom.

The protective mesh means that loose material does not drop down onto the

tractor (optional extra).

Maxi Grapple is used particularly in the USA and Canada for handling

round bales (large opening of 2 m), loose hay, twigs and branches, loose si-

lage, manure and for general bucket work. Teeth, protective mesh and grap-

ple arm can easily be removed when only the bucket is to be used.

Multigrab HD is a very powerful implement. When filling silage, the bucket

tip is advanced towards the silo, the powerful upper arm is pressed down

through the silage and into the bucket. The special design of the teeth cre-

ates a block with a good cut surface. This reduces the admission of air and

heat generation in the silage. Thanks to its incredible strength, the Multi-

grab HD can also be used for many other demanding fork and bucket tasks.

Three advantages that make a lot of difference: Our manure forks are

equipped with a specially hardened box section that neither deforms nor

turns when working. The tines are installed before the implement is painted

– metal to metal. The tines are secured with a very high torque.

All in all, you get an implement with a longer service life.

Multigrab hd 160 180 200 Weight 460 kg 500 kg 560 kg

Width 160 cm 180 cm 200 cm

Volume 0.86 m3 1.00 m3 1.14 m3

Depth 80 cm 80 cm 80 cm

Maxi Grapple 210 210 t 240 Weight 605 kg 620 kg 640 kg


Depth 81 cm 81 cm 86 cm Teeth – 24 cm –

240 t 260 260 t Weight 655 kg 710 kg 730 kg



Teeth 24 cm – 27 cm

Selecto F


t changes

Manure fork 130 150 170 Weight 123 kg 136 kg 152 kg



Number of tines 7 8 9

190 230 Weight 165 kg 203 kg

Width 190 cm 230 cm

Depth 85 cm 85 cm

Number of tines 10 12


12

5

6

3

4

Buckets

We all know that today’s buckets are subjected to larger loads and more hours of operation than before. Both tractors and front loaders have been made larger and more powerful.

The buckets need to be wider and hold a larger volume. We have therefore cho-sen an even stronger and better grade of steel. In addition, we use profile-pressed and laser cut sheet-metal. This unifies the need for extra strength with the desire for an attractive design.

1. The buckets have a round bottom and a conical shape. Numerous small bends make the bucket strong and the conical design allows simple filling and complete emptying.

2. In order to achieve even greater torsional strength and stability, the wider buckets have been supplied with an extra, profile-pressed, double back plate (not on the L and LV models). With the aid of a special overlap design, the HV buckets now have a hole profile along the implement hooks, which makes these buckets stronger and more stable.

3. The upper edge of the bucket back is pressed in a U-profile. In this area on the HD buckets there is a further welded angle profile along the length of the bucket.

4. The ends have a profile extrusion that makes the sides even stronger (not on the L and LV models). At the bottom is a welded triangular wearing piece, which simultaneously stabilises the cutting edge. On the HD buckets, this wearing piece runs all the way up along the end side.

5. All buckets have extremely strong cutting edges (500 Brinell). Depending on bucket model and size, 12, 16 or 20 mm thick and 100, 150 or 200 mm wide cut-ting edges are used. Together with the parallel reinforcing bars, the bucket bot-tom consequently extremely strong, torsionally stable and hard-wearing.

6. The implement hooks also contribute to a strong construction. Note that both hooks and locking holes are located along a bend. Depending on bucket model and size, there may be a double profile inside the bucket.

A bucket is not just a bucketAll buckets are conical and are therefore easy to fill, as the material does not need to be pressed into the bucket. The conical, “hopper-shaped” design also allows rapid and complete emptying of the bucket.

No matter what your needs are or what demands you stipulate, you will be able to find your new bucket in our range. There are six different models and a total of 21 different variants. There is also a special, high tip bucket and a grading bucket.

The non-spill bucket

Non-drop designIt has been a natural objective to design and produce a bucket that does not

allow spillage. What’s the point of having a bucket with a large volume if it

cannot be properly filled, or if it spills material? Our buckets therefore have

laser-cut ends. As a result, it is possible to create a bucket design where the

rear edge and in particular the front edge are especially high. It is now pos-

sible to completely fill the bucket. You have complete control over the mate-

rial, and the bucket does not drop any material.


Series h 135h 160h Volume (heaped) 0.54 m3 0.65 m3

Width 135 cm 160 cm

Depth 81 cm 81 cm

Height 75 cm 75 cm

Cutting edge WxT 150/16 mm 150/16 mm


Series h 185h 210h 240h Volume (heaped) 0,72 m3 0,82 m3 0,95 m3



Height 75 cm 75 cm 75 cm

Cutting edge WxT 150/16 mm 150/16 mm 150/20 mm

Weight 205 kg 252 kg 294 kg

Series ht 135ht 160ht Volume (heaped) 0.54 m3 0.65 m3

Width 135 cm 160 cm

Depth 81 cm 81 cm

Height 75 cm 75 cm


Number of teeth 6 7


Series ht 185ht 210ht Volume (heaped) 0.72 0.82

Width 185 cm 210 cm

Depth 81 cm 81 cm

Height 75 cm 75 cm


Number of teeth 8 9


Series hd 185hd 210hd Volume (heaped) 0,72 m3 0,82 m3

Width 185 cm 210 cm

Depth 81 cm 81 cm

Height 75 cm 75 cm



240hd 260hd Volume (heaped) 0.95 m3 1.03 m3

Width 240 cm 260 cm

Depth 86 cm 86 cm

Height 75 cm 75 cm



Series H Series HT Series HD

Contracting bucket. The very strongest buckets in the series. They are based

on the H bucket. On the 210, 240 and 260, the metal is 20 % thicker how-

ever. In addition, the HD buckets have a more powerful cutting edge, a

wider, longer floor reinforcement, an extra angle reinforcement on the inside

of the bucket along the implement hooks, as well as an angled wearing rail

on the rear of the bucket.

The soil bucket – the most popular in the range – can do everything. The

short bucket bottom makes the bucket strong and well suited to heavier

tasks. The three large buckets have an extra profile and round pressed back

plate across the full width.

Soil bucket with teeth. Same design as series H.


Buckets

Series lv 200lv 220lv Volume (heaped) 1.13 m3 1.25 m3

Width 200 cm 220 cm

Depth 100 cm 100 cm

Height 85 cm 85 cm



Series hv 200hv 220hv Volume (heaped) 1.16 m3 1.28 m3

Width 200 cm 220 cm

Depth 104 cm 104 cm

Height 85 cm 85 cm



240hv 260hv Volume (heaped) 1.70 m3 1.85 m3

Width 240 cm 260 cm

Depth 109 cm 109 cm

Height 98 cm 98 cm



A strong material and snow bucket. The series is aimed at users who require

a large volume. The generous volume measurements are achieved by de-

signing the bucket deeper and taller. All models have double profiles in the

bottom as well as along the implement hooks. There is consequently extra

strength where the stresses are greatest.

Series hv Series l Series lv

Light bucket. If the bucket is only to be used for lighter duties, the L bucket

is an excellent choice. The bucket is designed for customers who value

functionality ahead of technical benefits. The price is therefore extremely

competitive.

Light Volume bucket. This bucket series is suitable for handling grain,

manure, grass seeds, wood chips and other materials with a low volume

weight. The buckets have two vertical reinforcements along the implement

hooks.

In the emptying position, the front loader’s effective emptying stop ensures

controlled and complete emptying of the implement. Note also how the

“boomerang-shaped” link on the front loader contributes to a maximum

emptying angle.

Th

e best choice

A good ch

oice

Which bucket should I choose?

Areas of application H HT HV HD L LV

Light excavation and loading work

Loading of e.g. grain, wood chips and snow

Loading of lighter materials at high level

Heavy excavation and loading work

Work in gravel/sand, earth and stone

Contract work in gravel/sand, earth and stone

Grading work

Professional snow clearance

Grading

bucket

High

tip

Series l 130l 180l Volume (heaped) 0.51 m3 0.71 m3

Width 130 cm 180 cm

Depth 80 cm 80 cm

Height 75 cm 75 cm



Selecto F


t changes


Universal fork

High tip bucket 230

Volume (heaped) 2.00 m3

Width 230 cm

Depth 120 cm

Height 120 cm

Cutting edge WxT 150/20 mm

Weight 480 kg

Stone fork - Pro 150 200 Width 150 cm 200 cm

Depth 100 cm 100 cm

Height 73 cm 73 cm

Number of bottom tines 14 18

Tine distance 11 cm 11 cm


Universal fork 150 200 Width 150 cm 200 cm

Height 73 cm 73 cm

Tine length 98 cm 98 cm

Number of bottom tines 14 18

Tine distance 11 cm 11 cm


Stone fork – Professional

Forks

GRADING bucket 220

Volume (heaped) 0.65 m3

Width 220 cm

Depth 110 cm

Height 50 cm

Cutting edge WxT 150/20 mm

Weight 337 kg

High tip bucket Grading bucket

Without doubt the most powerful stone/universal fork on the market.

On the specially hardened box section, which does not become deformed

under load, powerful stone fork tines are installed. The back comprises five

transverse 80 x 40 profiles. The design

is incredibly torsionally rigid, at the

same time as offering excellent vis-

ibility. On the sides, the forks

are supplied with powerful

Hardox teeth.

A powerful grading bucket. Thanks to the low back plate and the long,

strong base, the driver has perfect visibility to the tip of the bucket. The

bucket is supplied with a 20 mm, powerful cutting edge. On the rear, below

the 20 mm thick subframe plates, is a welded 10 mm thick angle iron, which

reinforces the bucket for grading jobs.

The high tip bucket increases the unloading height by 120 cm. As a result,

even a short, compact front loader can fill a high trailer if necessary.

The bucket tips over its front edge, and it is not therefore necessary to

wait for the front edge to be lifted over the truck side before you reverse

away. This saves time and increases productivity.

High tip buckets are used for handling voluminous materials at high lev-

els, for example for loading grain, grass seed, beet or wood chips.

“Pick up and keep”. The distinctive design provides considerable potential

to fill the implement without dropping any stones already contained in the

bucket. At the front, special downward-

angled tines made of Hardox steel are

installed. After many hours of work,

these can easily be replaced.

The cross tubes (50 x 100 mm)

provide stability for the 30 mm

thick tines. Note also that

the back of this model

is higher than on earlier

models.

Selecto F


t changes


Lifting implement

Pallet forks Big bag lifter

Big bag lifter Weight 118 kg

Max. load 800 kg

Widht 120 cm

Height 170 cm

The upper profi le is made in one piece. This profi le

with holes for lateral adjustment provides robust

securing of the forks. The load is distributed over a

large area thanks to the wide load-bearing surfaces

of the forks. With this special

design, breaks in the arm are

avoided and you get to operate

a very stable fork that does not

“dangle”. The forks are natural-

ly approved with a large safety

margin.

For safe handling of large bags. The

height of the hook above the ground is

normally the same as when the bot-

tom of the large bags is level with

the lowest point of the front loa-

der when the bags are hanging

from the big bag lifter. Note

the practical benefi t of having

the hook bent to the side. The

hook can easily be seen from

the driver’s seat.

Log grab attachment

Bale spike (one short and one long tine). For instal-

lation on the pallet fork subframe.

Suitable for 1,000 kg, 1,600 kg

and 2,500 kg fork kits.

Weight 24 kg

Weight 85 kg

Accessories - Pallet forks

Accessories

3-point linkageThis implement can be used like the tractor’s 3-point

linkage to help move some implements around the

farm. Available with either Euro or SMS hooks.

Counter-weight

Weight 78 kg

The counter weight is an extremely useful piece

of equipment to properly ballast your machine to

maintain weight on the tractor’s rear axle.

The counter-weight increases the stability for the

tractor-loader unit. Connecting and disconnecting of

the counter-weight is made very easily with help

of the attached coupling axle, which has a bracket that

prevents the weight from coming off during work.

Bale spike

Pallet forks

1,000 kg 1,600 kg 2,500 kg Weight 122 kg 160 kg 170 kg

Max. load 1,000 kg 1,600 kg 2,500 kg


Fork

length 97 cm 97 cm 120 cm

Fork heigth 50 cm 92 cm 95 cm

Fork type profi le wrought wrought

The counter-weight is available in two sizes and is always delivered empty.

Weight, empty Weight, fi lled

(not factory fi lled)

186 kg 800 kg with concrete

212 kg 1000-1200 kg with concrete

NB: fi lled weight can be increased with metal


Your security first and foremost

A loader’s service life and efficiency increase if it has access to good service. When you choose a Quicke loader, you have a strong global organisation behind you.

In recent years we have invested even more in building up a comprehensive service network. In order to provide you with the best possible back-up, the entire organisation works towards a single goal: 100 % customer satisfaction.

• Absolute customer focus. In order to support you as a customer, we have built up procedures that ensure all departments in our

organisation concentrate on your needs.

• Proximity. Our world-leading distribution network is guaranteed to be close to you, no matter where you are.

• Extensive spare parts network. Spare parts are available from our subsidiary companies and from major Quicke representatives

all over the world.

• Rapid assistance on the web. Via Internet you have access to spare parts information, instructions and other vital information.

• Global technical support. As a Quicke customer, you always have access to rapid technical support. All over the world, our repre-

sentatives can provide knowledgeable and appropriate service.

• Continuous follow-up. Your opinions and suggestions for improvements to our product range are gathered up and processed

centrally. This process acts as a valuable foundation when we develop new loaders, implements and subframes. The new Quicke

Dimension is the fruit of close co-operation with users all over the world!

ps.

po

nd

us:

060

5. p

ho

to: j

ost

ein

ske

idsv

oll.

rep

ro: Z

irco

n M

edia

The Quicke dimension | www.quicke.nu

Some front loaders in this brochure are fitted with extra equipment. Certain products may be optional extra equipment. Some of the products are not available on all markets. Working with front loaders and accompanying implements is not without risk. Serious injuries to people and damage to materials can occur in the event of incorrectly carried out work. Show consideration to your surroundings, use com-mon sense and comply with local laws and regulations. Always read carefully through the instruction manual supplied. Only use original spare parts and accessories. Ålö’s product range is continually being

developed. We reserve the right at any time to alter specifications, prices and versions with no obligation on our part.®, ™ Trademarks of Ålö AB.

Ålö AB, SE 901 37 Umeå, Sweden Tel: +46 (0)90-17 05 00. Fax: +46 (0)90-17 05 99

www.alo.se

Best

nr 1

114

4328