COMPUTER & INFORMATION TECHNOLOGY IMPORTANT QUESTIONS FOR SEMESTER EXAM

SUB- ELECTRICAL ENGINEERING Prepared by – Mr. Vijay Balu Raskar

Supporting student-Mr. Amol Budkhe (COM) vijayraskar2003@yahoo.co.in

S NO. NAME OF CHAPTER MARKS

1 D.C Circuit 20

2 A.C Fundamental 24

3 Poly Phase Circuit 16

4 Transformer 16

5 Rotating Machines 16

6 Installation, Earthing & Troubleshooting 08

NOTE:- Four important things to attend lecture. Scientific calculator. Blue, Black & Red color pens. Physically & mentally presence in the class.

Try to practice examples at home. Be prepare for next class. Be regular as clock.

ALL THE BEST

1. D.C. Current V. IMPORTANT

1. What is Ohms law?

2. Differentiate between the terms

(a) Active & Passive Network.

(b) Unilateral & Bilateral Network.

(c) Linear & Non-Linear Network.

3. State and explain kirchhoffs current and voltage law.

4. Derive expressions for the conversion of a star-connection network into equivalent

delta-connection networks and vice versa.

5. Classification of network.

OTHERS 6. Define the term resistance, specific resistance and conductance of a material. State

units.

7. What are the factors on which the resistance of a material depends? What is

resistance?

8. Prove that in a D.C. series circuit total resistance is equal to the sum of individual

resistance.

9. Drive the expression for equivalent resistance of a circuit having several resistance

connected in parallel.

10. Represent the following by their symbols.

(a) Ideal and Practical voltage source. Amol

(b) Ideal and Practical current source.

2. A.C. FUNDAMENTALS V.IMPORTANT

1. What is an alternating current? Compare it with a direct current.

2. With reference to alternating quantities, define the following terms:

Waveform, Cycle, Frequency, Amplitude and Periodic Time.

3. Define RMS value of alternating current quantities. Prove that in alternating

quantities varying sinusoidally the maximum value in 2 times the RMS value.

OTHERS 4. Define peak factors and form factors. State their values for sinusoidal

quantities.

5. Derive equation of alternating voltage and current.

3. Poly Phase Circuits V. IMPORTANT

1. State any tow practical application of a choking coil.

2. As applied to a.c circuits, explain the terms.

(a) Apparent power. (b) True power. (c) Reactive power. State their units.

4. Explain the difference between a single phase and a poly-phase system. Amol

5. Define:- 1. Symmetrical system.

2. Phase sequence.

6. For star and delta-connected loads, state numerical relationship between

(i) Line current and phase voltage.

(ii) Line voltage and phase voltage.

Also state that the expression for power in the term of line voltage, line current

and power fraction.

OTHERS 7. What is an impedance triangle?

8. Explain with reference to three-phase system, the term ‘balanced load’ and

‘balanced supply system’.

4. Transformers V. IMPORTANT

1. Define Transformer. Why Transformers are measured in KVL.

2. Explain types of transformers.

3. Explain

(i) Auto transformers.

(ii) Ideal transformers.

(iii) Isolation transformers.

4. What is meant by step-up and step-down transformers?

5. Rotating Machines 1. Derive EMF equation of motor.

2. Write a short note on.

(i) Types of DC motors.

(ii) Characteristic of DC motors.

(iii) Starter.

(iv) Speed control of DC motor.

6. Installation, Earthing, and

Troubleshooting 1. Explain.

(i) Types of wire.

(ii) Fuse.

(iii) HRC fuses.

(iv) MCCB

(v) MCB

(vi) ELCB

(vii) Necessity of earthing. Amol

(viii) Plate earthing.

(ix) Pipe earthing.

2. Explain basic principle of operation of a circuit breaker.

3. What is trouble shooting? Discuss briefly the various problems encountered in

the wiring installation for the computers.

4. Why earthing essential in a wiring?

5. Define

I. Current rating

II. Minimum fusing current.

III. Fusing factor

NOTE:-

Preferences for practicing all problems

1) Transformer.

2) DC motor.

3) AC fundamentals.

4) DC circuit.