BOC TECHNICAL WEBINAR SERIES · 2017. 5. 16. · BOC TECHNICAL WEBINAR SERIES THE ESSENTIAL...

BOC TECHNICAL WEBINAR SERIES

THE ESSENTIAL CREDENTIALN O R T H W E S TENERGY EFFICIENCY COUNCIL

SPEAKERS:Kevin Fish, Sr. Associate, Strategic Energy Group

Scott Lindquist, Operations Manager,University of New Hampshire

www.TheBOC.info

Troubleshooting Common Air Handler Problems

May 17, 2017 11:00am Pacific Time

LEARN. LEAD. SUSTAIN

Thank You to our Sponsors

LEARN. LEAD. SUSTAIN3

Did you know? More than “360” students have graduated from NorthWestern’ssponsored IBOA training program since 1999.

LEARN. LEAD. SUSTAIN

Webinar Quiz

http://www.theboc.info/boc1705

This presentation is intended for use by the Building Operator Certification program. No copy or use of this presentation should occur without the permission of NEEC and speakers.

LEARN. LEAD. SUSTAIN

Learning Objectives

▪ Understand the configuration of an air handling unit

▪ Understand common problems and how to address them

▪ Learn different tools and devices to measure air flow

▪ Understand and learn to establish and document procedures for troubleshooting & response

Webinar Quiz: http://www.theboc.info/boc1705

LEARN. LEAD. SUSTAIN

Today’s Speakers

Kevin Fish Scott Lindquist

LEARN. LEAD. SUSTAIN

▪ Understand the configuration (hardware and software)!

▪ Get eyes on control system (if BAS)

▪ Get eyes on the unit

▪ Understand the root cause

▪ Consider possible undesired consequences

▪ Make changes as small and as temporary…

In general, when problem arises…

LEARN. LEAD. SUSTAIN

Hardware configuration

▪ Type of unit, return/relief, control, volume control

▪ Outside air capacity & damper config.

▪ Type of terminal units, TU control, TU reheat

▪ Type of heating / cooling in AHU

▪ Location of controlling duct static pressure (DSP) sensor

Understand the configuration /

intent of the AHU!

LEARN. LEAD. SUSTAIN

Understand the configuration /

intent of the AHU (cont’d)

Software configuration

▪ What is the official setting for the following? How was it determined?

▪ Optimal start; Night Low Limit setpoint

▪ Damper control: Min OA & Economizer

▪ CO2 sensor setpoints

▪ DAT & DSP setpoint / reset

▪ Night setback of TU airflow

LEARN. LEAD. SUSTAIN

▪ Electrical / VFD / Control problem

▪ Broken belts

▪ Failed motor

▪ Fan bearing failure

▪ Freeze stat trip…

AHU won’t run / no airflow

LEARN. LEAD. SUSTAIN

(Trouble achieving DSP setpoint or VFD at higher than normal speed)

▪ Obstructed coils, OA intakes, filters, turning vanes

▪ Fan turning backwards

▪ Fan bearing issues

▪ VFD issue

▪ DSP setpoint too low / high

▪ Damper issues

▪ AHU door left open, duct separation

Lack of sufficient airflow

LEARN. LEAD. SUSTAIN

▪ Insufficient water temp or pressure

▪ Leaky valves

▪ Faulty control signal to valves

▪ Valve won’t open completely

▪ DX cooling or gas pack issues

Lack of sufficient heating / cooling

LEARN. LEAD. SUSTAIN

▪ Improper settings on MinOA and OA dampers

▪ Linkage issues

▪ Actuator issues

▪ Bound/frozen dampers

▪ Blade “flops”

Damper / Economizer issues

LEARN. LEAD. SUSTAIN

▪ Document hardware and software configurations

▪ Look for control points that are overridden / manual

▪ Focus on root causes

▪ Address issues at the most local level

▪ What is the least energy intensive response

Establish and document procedures for troubleshooting & response

LEARN. LEAD. SUSTAIN

Periodic scheduled review is highly recommended

▪ Physical checks of AHU

▪ Review of BAS graphic screens

▪ Trend review of AHU function

3 types of verifications

LEARN. LEAD. SUSTAIN

Physical checks of AHU

▪ Function of dampers (OAD, RAD & EAD)

▪ CHW and HW valves close completely

▪ Check / replace filters

▪ Clean OA intakes, reclaim coils, airflow sensors

▪ Confirm sensor calibration (OA, airflow, others)

3 types of verifications (cont’d)

Sensor Error Causes

• Never Calibrated

• Only a simple comparison check

• Calibrated with inaccurate reference tool

• Incorrect placement (esp. OSA, mixed air and pressure)

• Incorrect type sensor (i.e. bulb type vs averaging)

• Failed, cut wires or offline sensors (can paralyze control algorithms)

• Deteriorated connections (Water intrusion/condensation causes corrosion

Outside Air Temperature Sensors

▪ Starting/stopping equipment

▪ Used for locking out heating and cooling

modes

▪ Resetting of setpoints

▪ Also for freeze protection

Why would Outside air temperature be a critical sensor?

Location, location, location

LEARN. LEAD. SUSTAIN

Review of BAS graphic screens

▪ Set-points and resets are reasonable / official

▪ No overridden values

▪ Point values are reasonable (especially in relation to each other)

▪ Summary screen of terminal unit damper positions

3 types of verifications (cont’d)

What’s wrong with this picture?

Simultaneous Heating & CoolingHeating valve open 26% while Cooling valve open 23%

What’s wrong with this picture?

Over-Economizing! OSA damper 100% open

AND Heating Valve open 20% !

LEARN. LEAD. SUSTAIN

Trend review of AHU function

▪ Scheduling and Optimal Start

▪ Values change, and change reasonably

▪ Economizer function

▪ Setpoints are reset and satisfied / maintained

▪ Fan speeds modulate

▪ Simultaneous heating & cooling?

3 types of verifications (cont’d)

time for … Q&A

LEARN. LEAD. SUSTAIN

Air apparatus Test Report

time for … Q&A

LEARN. LEAD. SUSTAIN

Washington & Oregon• Smart Buildings Center - http://www.smartbuildingscenter.org/tool-library/

Idaho

• University of Idaho – Integrated Design Lab - http://www.idlboise.com/tool-loan-library

California• Pacific Gas & Electric - http://www.pge.com/pec/tll/

• Sonoma County - http://sonomacountyenergy.org/resources/contractor-resource-center/tool-lending-library/

• Southern California Edison - https://www.sce.com/wps/portal/home/business/consulting-services/energy-educationcenters/tulare/!ut/p/b1/hdBNb4MwDAbgX8OVmCRldDdDGSRizRjVSnOZ6MQoEyUVZeXvL6u6w759s_W8lmyiSUl0X53aphpb01fde6_9RykW6CWcikDiDMRSFWmMdzSaexZsLIBfCuG__JroM_GCBFNRgFB8wUGEqyy8CW4Z9-EbCIVvQYSRUhIg97-C5P6KgpAPcaZCjwKnFzBPIE6lsmCVMxAsh2WByAA-NvxxhSS66cz2_JEN9lsWNEQP9XM91IP7OtjxbhwPx2sHHJimyW2MabrafTJ7B36K7MxxJOVnSQ77ElrxMutOGb4BKlagaA!!/dl4/d5/L2dBISEvZ0FBIS9nQSEh/?from=agtac

• San Diego Gas & Electric - https://c95021.eos-intl.net/C95021/OPAC/Index.aspx

New York• CUNY Building Performance Lab - http://www.cunybpl.org

Tool Lending Library Locations

| THE ESSENTIAL CREDENTIAL

IMPROVE YOUR FACILITY & CAREER

• DEMAND REDUCTION• LIGHTING• ENERGY MANAGEMENT

• BUILDING SCOPING• O&M STRATEGIES• INDOOR AIR QUALITY

www.theboc.info877-850-4793 (toll free)

bocinfo@theboc.info

BOC National Partner Network

LEARN. LEAD. SUSTAIN

Take the Webinar Quiz: www.theboc.info/boc1705

➢ Earn 1.5 points today towards the maintenance of your BOC certification *

Maintain Your BOC Credential

Maintenance Application Deadline: March 31

* Make sure to keep a record of your webinar attendance and quiz completion for next year’s maintenance application

LEARN. LEAD. SUSTAIN

➢September TBD - Addressing Hot and Cold Calls –What’s your Procedure?

➢ October 18 - Building Re-tuning without a Building Automation Systems

Upcoming Webinars