View
1
Download
0
Category
Preview:
Citation preview
DT175 - 2
TDS PROJECT 2 - Concrete
Aidan McKenna
D19124287
March 2020
TDS Project 2 - Concrete, Sheet List.
Count Sheet Number Sheet Name
1 04/02 - 101 Cover Sheet
1 04/02 - 201 Site Plan
1 04/02 - 202 Basement Floor Plan
1 04/02 - 203 Ground Floor Plan
1 04/02 - 206 Second Floor Plan
1 04/02 - 208 Fifth Floor Plan
1 04/02 - 221 Section A-A
1 04/02 - 222 Section B-B
1 04/02 - 223 Elevations
1 04/02 - 230 Key Reference Section
1 04/02 - 231 Typical Details
1 04/02 - 232 Typical Details
1 04/02 - 240 Facade Panel Study
1 102 3 4 5 6 7 8 9 11
12
13
14
15
16
17
18
19
20
M1
M2
RWDP
**.** CL**.** IL
AJ
MH
SURFACE WATER DRAINAGE:
FOUL WATER DRAINAGE:
COVER LEVEL:INVERT LEVEL:
ARMSTRONG JUNCTION 300x300mm:
MANHOLE 600x600mm:
COMMUNICATIONS:
MAINS WATER:
MAINS POWER:
GAS SUPPLY:
LEGEND:
STREET LAMP STANDARD:
NOTE:ALL UTILITY AND SERVICE CONNECTIONS TO ONLY BE MADE WITH THE AUTHORISATION AND APPROVAL OF THE SERVICE PROVIDER AND LOCAL AUTHORITY. LOCAL AUTHORITY ROAD OPENING LICENCES TO BE OBTAIN PRIOR TO COMMENCEMENT OF CONNECTION WORKS.
LP
HYDRANT / METER: H
MH
M
27.8
27.7
RWDP
SVP
RWDP
RWDP
RWDPRWDP
RWDP
1:60
fall1:60 fall
1:60 fall1:60
fall
1:60 fall
RWDP
1:60 fall 1:60
fall
1:60
fall 1:60 fall
1:60 fall
1:60
fall
1:60
fall
1:60 fall
1:6
0 fal l
1:60 fall
SMHCL 27.8IL 26.8
FMHCL 27.8IL 27.05
Wate
r
Tele
com
s
Main
s P
ow
er
Pow
er
Tra
nsfo
rmer
H
M
Water
Telecoms
Mains Power
FMH 1CL 27.90IL 27.20
SMH 1CL 27.90IL 26.92
Brookfield Road
LP
North
--
Scale
Checked by
Drawn by
Date
Project number
1 : 200
19/0
3/2
020
12:1
9:2
4
Site Plan
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
Staff
04/02 - 201
1 : 200
00 Site Plan1
Outline of Basement Level
Outline of Basement Level
Outlin
e o
f B
asem
ent L
eve
l
-
-
-
-
1
04/02 - 221
1 2 3 4 5 6 7
E
D
C
B
A
M1 M2
1
04/02 - 222
1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
17 18
19
20
Outline of Ground Floor above
Outline of Ground Floor above
Outlin
e o
f G
round F
loor
above
Outline of Ground Floor above
Natural Ventilation Duct A
Natural Ventilation Duct B
Natural Ventilation Duct C
NaturalVentilation
Duct D
26.0
Stair Core 11
Refuge Area and emergency callpoint as per TGD Part B
Store Room2
Riser A3
Lobby4
Stair Core 25
Riser B7
Plant Room8
Refuge Area and emergency callpoint as per TGD Part B
Clear Access Area as per TGD Part M
300mm Reinforced in-situ Concrete basement wall to Engineer's Details with a Bitimen Waterproofing Self-adhesive Tanking Membrane (Proofex 3000or similar) installed to manufacture' details and spectication.100mm XPS water resistant rigid insulation as protective layer to face oftanking membrane.
Aluminium Louvre System with mesh backing and selected finish (Crossflow or similar)
148
FD60
149FD60
188
FD60
209FD60
211
FD60
213
FD60
FD60336
FD60
337
Precast concrete stairs and landing with 200mm wrist depth150mm riser, 250mm going (Quinn Building Products) installedby maunfacturer to Engineer's details.100mm dia HRS (hollow round section) mild steel handrails on 25mm dia round bar ballustrades @ 100mm max c/c allpowder coated to RAL ref. 1003 (safety yellow) protected forinstallation. All in accordance with TDG part M
250mm reinforced insitu concrete core wall constructed to Engineer'sdetails and specifications.
400 x 400mm reinforced in-situ concrete columns toEngineer's details
Otis Gen2 Flex passanger lift. Internal finishes and spec to be agreed.
Reinforced in-situ concrete basement floor slab to Engineer's details on XPS rigid insulation as void filler on Radon barrier membrane (Monarflex RMB400) lapped and taped at joints to manufacturer's spec on 50mm sand layer on 150mm compacted graded hardcore
Aluminium Louvre System with mesh backing and selected finish (Crossflow or similar)
Aluminium Louvre System with mesh backing and selected finish (Crossflow or similar)
Aluminium Louvre System with mesh backing and selected finish (Crossflow or similar)
Car park floor coated with Epoxy Flex coating
Reinforced in-situ concrete basement ramp at 1:10 gradient to Engineer's details on XPS rigid insulation as void filler where required on 50mm sand layer on compacted graded hardcore
250mm reinforced insitu concrete retaining ramp wall constructed to Engineer's details and specifications.
Disabled parking spaces as per TGD Part M sec 1.1
AOVabove
AOVabove
TD 20m
TD 20m
TD
9.2
m
TD
8.4
m
TD 9.7m
TD 8.5m
TD 8
.2m
Fou
ls w
ate
r pip
e r
un to b
e c
onfirm
ed
300mm Reinforced in-situ Concrete basement wall to Engineer's Details with a Bitimen Waterproofing Self-adhesive Tanking Membrane (Proofex 3000or similar) installed to manufacture' details and spectication.100mm XPS water resistant rigid insulation as protective layer to face oftanking membrane.
Foul soill vent pipefrom above WC Riser
Precast concrete stairs and landing with 200mm wrist depth150mm riser, 250mm going (Quinn Building Products) installedby maunfacturer to Engineer's details.100mm dia HRS (hollow round section) mild steel handrails on 25mm dia round bar ballustrades @ 100mm max c/c allpowder coated to RAL ref. 1003 (safety yellow) protected forinstallation. All in accordance with TDG part M
250mm reinforced insitu concrete core wall constructed to Engineer'sdetails and specifications.
--
Scale
Checked by
Drawn by
Date
Project number
1 : 100
19/0
3/2
020
12:1
9:2
5
Basement Floor Plan
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
Staff
04/02 - 2021 : 100
-01 Basement FFL1
1
04/02 - 221
1 2 3 4 5 6 7
E
D
C
B
A
1
04/02 - 222
1
12
13
24
1
12
13
24
Natural Ventilation Duct
Precast concrete stairs and landing with 200mm wrist depth150mm riser, 250mm going (Quinn Building Products) installedby maunfacturer to Engineer's details.100mm dia HRS (hollow round section) mild steel handrails on 25mm dia round bar ballustrades @ 100mm max c/c allpowder coated to RAL ref. 1003 (safety yellow) protected forinstallation. All in accordance with TDG part M
250mm reinforced insitu concrete core wall constructed to Engineer'sdetails and specifications with precast facade system and insulation to exterior.
300 x 300mm reinforced in-situ concrete columns toEngineer's details
Otis Gen2 Flex passanger lift. Internal finishes and spec to be agreed.
AOVabove
AOVabove
103
FD60
104
FD60
106
FD60
107FD60
189
FD60
196FD60
212
FD60
267FD60
FD60
272
FD60
273
340
341
Stair Core 11
Riser A3
Stair Core 25
Riser B7
Cleaner Store9
ProtectedLobby
Ladies WC
Gents WC
DisabledWC
Clear Access Area as per TGD Part M
Natural Ventilation Duct
TD 20m
TD 11.5m
TD 15m
TD 18m
Precast concrete stairs and landing with 200mm wrist depth150mm riser, 250mm going (Quinn Building Products) installedby maunfacturer to Engineer's details.100mm dia HRS (hollow round section) mild steel handrails on 25mm dia round bar ballustrades @ 100mm max c/c allpowder coated to RAL ref. 1003 (safety yellow) protected forinstallation. All in accordance with TDG part M
250mm reinforced insitu concrete core wall constructed to Engineer'sdetails and specifications with precast facade system and insulation to exterior.
1590 4500 7000 5500 5500 5500 5550 1540
1590
5500
5500
5500
5500
1590
4945
4380 2000
2500
1800
2460
3450
4380
2600
2400
3000
7225
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
Toilet Block walls to be 70mm Gyproc "C" aluminium frame stud frame as to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating on both sides of partition.
Aco slot drainage channel at entrance doors
Proposed Cafe
Reception
Office/Meeting Area
Layout to be confirmed
Layout to be confirmed
Outlin
e o
f B
ase
ment
belo
w
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
Powder coated mild steel ventilation ground louvre with mesh backing and selected finish (Crossflow or similar)
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame as to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Aco slot drainage channel
2950
7150
1590
5500
5500
5500
5500
1590
1590 7000 5500 5500 5500 5550 1540
Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame as to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
FirePanel
EXIT
EXIT
2790 3140 2300 3140 2200 3140 2470 3140 2860
Powder coated mild steel ventilation ground louvre with mesh backing and selected finish (Crossflow or similar)
2290 3140 13680 910 3140 2000 3140 8380
2590
3140
2460
3140
2850
510
3140
1850
6390
1200
1860
3140
1590
SVP
Scale
Checked by
Drawn by
Date
Project number
1 : 100
19/0
3/2
020
12:1
9:2
7
Ground Floor Plan
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
Staff
04/02 - 203
1 : 100
00 Ground FFL1
1
04/02 - 221
1 2 3 4 5 6 7
E
D
C
B
A
1
04/02 - 222
1
12
13
24
1
12
13
24
Precast concrete stairs and landing with 200mm wrist depth150mm riser, 250mm going (Quinn Building Products) installedby maunfacturer to Engineer's details.100mm dia HRS (hollow round section) mild steel handrails on 25mm dia round bar ballustrades @ 100mm max c/c allpowder coated to RAL ref. 1003 (safety yellow) protected forinstallation. All in accordance with TDG part M
300 x 300mm reinforced in-situ concrete columns toEngineer's details
250mm reinforced insitu concrete core wall constructed to Engineer'sdetails and specifications with precast facade system and insulation to exterior.
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame as to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Clear Access Area as per TGD Part M
Ladies WC
Gents WC
Disabled
WC
Protected
Lobby
EXIT
EXIT
AOVabove
AOVabove
Refuge Area and emergency callpoint as per TGD Part B
4500 7000 5500 5500 5500 5550
5500
5500
5500
5500
SVP
1
12
13
24
300 x 300mm reinforced in-situ concrete columns to Engineer's details
Otis Gen2 Flex passanger lift. Internal finishes and spec to be agreed.
Precast concrete stairs and landing with 200mm wrist depth150mm riser, 250mm going (Quinn Building Products) installedby maunfacturer to Engineer's details.100mm dia HRS (hollow round section) mild steel handrails on 25mm dia round bar ballustrades @ 100mm max c/c allpowder coated to RAL ref. 1003 (safety yellow) protected forinstallation. All in accordance with TDG part M
250mm reinforced insitu concrete core wall constructed to Engineer'sdetails and specifications with precast facade system and insulation to exterior.
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Toilet Block walls to be 70mm Gyproc "C" aluminium frame stud frame as to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating on both sides of partition.
Layout to be confirmed
Refuge Area and emergency callpoint as per TGD Part B
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Stair Core13
Cleaners Store14
Riser A15
Stair Core 217
Riser B18
Open Plan Office
TD 20m
TD 11.5mTD 15m
TD 18m
TD 25.5m
TD 1
2.5m
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
111.83°
Scale
Checked by
Drawn by
Date
Project number
1 : 100
19/0
3/2
020
12:1
9:2
7
Second Floor Plan
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
Staff
04/02 - 206
1 : 100
02 Second FFL1
-
-
-
-
- -
-
-
1
04/02 - 221
1 2 3 4 5 6 7
E
D
C
B
A
1
04/02 - 222
1
12
13
24
300 x 300mm reinforced in-situ concrete columns to Engineer's details
Otis Gen2 Flex passanger lift. Internal finishes and spec to be agreed.
Precast concrete stairs and landing with 200mm wrist depth150mm riser, 250mm going (Quinn Building Products) installedby maunfacturer to Engineer's details.100mm dia HRS (hollow round section) mild steel handrails on 25mm dia round bar ballustrades @ 100mm max c/c allpowder coated to RAL ref. 1003 (safety yellow) protected forinstallation. All in accordance with TDG part M
250mm reinforced insitu concrete core wall constructed to Engineer'sdetails and specifications with precast facade system and insulation to exterior.
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Toilet Block walls to be 70mm Gyproc "C" aluminium frame stud frame as to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating on both sides of partition.
Layout to be confirmed
EXIT
Clear Access Area as per TGD Part M
Ladies WC
Gents WC
Disabled
WC
Protected
Lobby
--
Refuge Area and emergency callpoint as per TGD Part B
SVP
AOVabove
Stair Core 110
Cleaner Store11
Riser A12
Office AreaRaised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
TD 17m
1500 4500 7000 5500 430
1500
5500
5500
1500
RWDP
RWDP
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
Aco slot drainage channel at entrance doors
50mm concrete paving slabs in selected colour and pattern (Tobermore Airclean VS50) with open joins on filter fleece layer on proprietary support drainage board (Bauder DS650) on waterproof membrane on 85mm XPSrigid insulation under paved area
1:60 surface drainage fall achieved in structural screed on 200mm precast hollow floor slabs to Engineer's detail
Extension Green Roof Area:Finish growing surface on WB vegitation matting on 100mm Extensive/Biodiverse substrate layer on filteration fleece membrane on water storage/ drainage layer (Bauder DSE20) to fall to boundary edges on polyester/polypropylene fibre protective layer
Automatically opening louvred smoke vent (Crossflow Eura)connected to building fire alarm panel installed by specialist
Roof Terrace and Green Roof Area
Flat roof bitimen capping sheet adhered to reinforced PVC underlayer membrane on PIR tapered foil backed insulation to 1:60 drainage fall on self-adhesive bitumen air & vapour control layer with foil facing (Bauder Thermofol PVC System)75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Scale
Checked by
Drawn by
Date
Project number
1 : 100
19/0
3/2
020
12:1
9:2
8
Fifth Floor Plan
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
Staff
04/02 - 208
1 : 100
05 Fifth FFL1
00 Ground FFL
28700
01 First FFL
32300
02 Second FFL
35900
03 Third FFL
39500
04 Forth FFL
43100
05 Fifth FFL
46700
06 Sixth FFL
50300
07 Seventh FFL
53900
08 Eighth FFL
57500
EDCBA
09 Top of Core
60100
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
Powder coated mild steel ventilation ground louvre with mesh backing and selected finish (Crossflow or similar)
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
300 x 300mm reinforced in-situ concrete columns to Engineer's details
Toilet Block walls to be 70mm Gyproc "C" aluminium frame stud frame as to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating on both sides of partition.
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
NaturalVentilation
Duct A
300mm Reinforced in-situ Concrete basement wall to Engineer's Details with a Bitimen Waterproofing Self-adhesive Tanking Membrane (Proofex 3000 or similar) installed to manufacture' details and spectication.100mm XPS water resistant rigid insulation as protective layer to face oftanking membrane.
Reinforced in-situ concrete basement floor slab to Engineer's details on XPS rigid insulation as void filler on Radon barrier membrane (Monarflex RMB400) lapped and taped at joints to manufacturer's spec on 50mm sand layer on 150mm compacted graded hardcore
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
50mm concrete paving slabs in selected colour and pattern (Tobermore Airclean VS50) with open joins on filter fleece layer on proprietary support drainage board (Bauder DS650) on waterproof membrane on 85mm XPSrigid insulation under paved area1:60 surface drainage fall achieved in structural screed on 200mm precast hollow floor slabs to Engineer's detail
Extension Green Roof Area:Finish growing surface on WB vegitation matting on 100mm Extensive/Biodiverse substrate layer on filteration fleece membrane on water storage/ drainage layer (Bauder DSE20) to fall to boundary edges on polyester/polypropylene fibre protective layer
Office Area
Office Area
Office Area
Office Area
Office Area
Office Area
Office Area
Meeting AreaReceptionCafe Area
Basement Car Park
PV Solar panels (Activ8) on flat roof mounting brackets supplied and installed by specialist at an incline angle of 35 degrees facing due SouthCabling and Invertor to M&E Engineer's details
3325
3175
3175
3175
3175
3175
3175
3175
2975
2825
2825
2825
2825
2825
2825
2825
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Reinforced concrete Pile and Pad foundationto engineers specifications.
Permeable ground drain connected to surface water drainage sumpprotected to geotech filter layer all bedded in grade water gravel
Proprietry PVC internal day joint Waterbar (Sika PVC-P NB Type A)
EPDM waterproofing layer adhered to concrete elements. EDPM paint to face of concrete structural elements applied in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive & Ultraflex Liquid Waterproofing)
Parapet upstand wrapped with EPDM waterproofing layer to adhered to concretesurface in accordance with supplier's spec, joints lapped and sealed with mineral wool insulation (Rockwool Duo Slab) surroundCement render board (Weber) to inner face with flat roof membrane dressed upPrecast concrete parapet panel by Techrete with stainless steel railing
Mineral wool fire stop strip
Cast in-situ reinforce concrete cantilever bean and upstand to Engineer's detail
Parapet upstand wrapped with EPDM waterproofing layer to adhered to concretesurface in accordance with supplier's spec, joints lapped and sealed with mineral wool insulation (Rockwool Duo Slab) surroundPrecast concrete parapet panel by Techrete with stainless steel railing
Flat roof bitimen capping sheet adhered to reinforced PVC underlayer membrane on PIR tapered foil backed insulation to 1:60 drainage fall on self-adhesive bitumen air & vapour control layer with foil facing (Bauder Thermofol PVC System)75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's detailsza
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
Scale
Checked by
Drawn by
Date
Project number
1 : 100
19/0
3/2
020
12:1
9:2
9
Section A-A
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
Staff
04/02 - 221
1 : 100
Section A-A1
00 Ground FFL
28700
01 First FFL
32300
-02 Top Found
25500
1
04/02 - 221
02 Second FFL
35900
-01 Basement FFL
26000
03 Third FFL
39500
04 Forth FFL
43100
05 Fifth FFL
46700
06 Sixth FFL
50300
07 Seventh FFL
53900
08 Eighth FFL
57500
1 2 3 4 5 67
09 Top of Core
60100
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
300 x 300mm reinforced in-situ concrete columns to Engineer's details
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Natural Ventilation Duct A 300mm Reinforced in-situ Concrete basement wall to Engineer's Details with a Bitimen Waterproofing Self-adhesive Tanking Membrane (Proofex 3000or similar) installed to manufacture' details and spectication.100mm XPS water resistant rigid insulation as protective layer to face oftanking membrane.
Reinforced in-situ concrete basement floor slab to Engineer's details on XPS rigid insulation as void filler on Radon barrier membrane (Monarflex RMB400) lapped and taped at joints to manufacturer's spec on 50mm sand layer on 150mm compacted graded hardcore
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
50mm concrete paving slabs in selected colour and pattern (Tobermore Airclean VS50) with open joins on filter fleece layer on proprietary support drainage board (Bauder DS650) on waterproof membrane on 85mm XPSrigid insulation under paved area1:60 surface drainage fall achieved in structural screed on 200mm precast hollow floor slabs to Engineer's detail
Extension Green Roof Area:Finish growing surface on WB vegitation matting on 100mm Extensive/Biodiverse substrate layer on filteration fleece membrane on water storage/ drainage layer (Bauder DSE20) to fall to boundary edges on polyester/polypropylene fibre protective layer
Office Area
Office Area
Office Area
Office Area
Meeting AreaReception
Basement Car Park
Office Area
Office Area
Office Area
Office Area
Reinforced in-situ concrete basement ramp at 1:10 gradient to Engineer's details on XPS rigid insulation as void filler where required on 50mm sand layer on compacted graded hardcore250mm reinforced insitu concrete retaining ramp wall constructed to Engineer's details and specifications.
Flat Roof AreaGreen Roof Area
3025
3175
3175
3175
3175
2875
2875
2875
2875
2150
Permeable ground drain connected to surface water drainage sumpprotected to geotech filter layer all bedded in grade water gravel
Proprietry PVC internal day joint Waterbar (Sika PVC-P NB Type A)
EPDM waterproofing layer adhered to concrete elements. EDPM paint to face of concrete structural elements applied in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive & Ultraflex Liquid Waterproofing)
Permeable ground drain connected to surface water drainage sumpprotected to geotech filter layer all bedded in grade water gravel
Parapet upstand wrapped with EPDM waterproofing layer to adhered to concretesurface in accordance with supplier's spec, joints lapped and sealed with mineral wool insulation (Rockwool Duo Slab) surroundCement render board (Weber) to inner face with flat roof membrane dressed upPrecast concrete parapet panel by Techrete with stainless steel railing
Flat roof bitimen capping sheet adhered to reinforced PVC underlayer membrane on PIR tapered foil backed insulation to 1:60 drainage fall on self-adhesive bitumen air & vapour control layer with foil facing (Bauder Thermofol PVC System)75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Scale
Checked by
Drawn by
Date
Project number
1 : 100
19/0
3/2
020
12:1
9:3
0
Section B-B
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
Staff
04/02 - 222
1 : 100
Section B-B1
00 Ground FFL
28700
01 First FFL
32300
02 Second FFL
35900
03 Third FFL
39500
04 Forth FFL
43100
05 Fifth FFL
46700
06 Sixth FFL
50300
07 Seven FFL
53900
08 Eight FFL
57500
09 Top of Core
60100
A B C D E
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade parapet by Techrete
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
Precast concrete facade parapet by Techrete
00 Ground FFL28700
01 First FFL32300
02 Second FFL35900
03 Third FFL39500
04 Forth FFL43100
05 Fifth FFL46700
06 Sixth FFL50300
07 Seven FFL53900
08 Eight FFL57500
09 Top of Core
60100
1 2 3 4 5 6 7
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade parapet by Techrete
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
00 Ground FFL
28700
01 First FFL
32300
02 Second FFL
35900
03 Third FFL
39500
04 Forth FFL
43100
05 Fifth FFL
46700
06 Sixth FFL
50300
07 Seven FFL
53900
08 Eight FFL
57500
09 Top of Core
60100
1234567
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade parapet by Techrete
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
00 Ground FFL
28700
01 First FFL
32300
02 Second FFL
35900
03 Third FFL
39500
04 Forth FFL
43100
05 Fifth FFL
46700
06 Sixth FFL
50300
07 Seven FFL
53900
08 Eight FFL
57500
09 Top of Core
60100
ABCDE
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
Precast concrete facade panel by Techrete on 200mm non-combustible mineral wood facade insulation with EPDM vapour control layer
Scale
Checked by
Drawn by
Date
Project number
1 : 200
19/0
3/2
020
12:1
9:3
1
Elevations
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
TU Staff
04/02 - 223
1 : 200
West Elevation1
1 : 200
South Elevation2
1 : 200
North Elevation3
1 : 200
East Elevation4
2
04/02 - 231
Sim
1
04/02 - 231
Sim
3
04/02 - 231
Sim
4
04/02 - 231
Sim
1
04/02 - 232
Sim
4
04/02 - 232
Sim
3
04/02 - 232
Sim
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall to Acco drainage channels
Powder coated mild steel ventilation ground louvre with mesh backing and selected finish and aluminum louvre with mesh backing to car park ope (Crossflow or similar)
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
EPDM waterproofing layer adhered to concrete elements. EDPM paint to face of concrete structural elements applied in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive & Ultraflex Liquid Waterproofing)
300 x 300mm reinforced in-situ concrete columns to Engineer's details
NaturalVentilation
Duct B
Reinforced in-situ concrete basement floor slab to Engineer's details on XPS rigid insulation as void filler on Radon barrier membrane (Monarflex RMB400) lapped and taped at joints to manufacturer's spec on 50mm sand layer on 150mm compacted graded hardcore
300mm Reinforced in-situ Concrete basement wall to Engineer's Details with a Bitimen Waterproofing Self-adhesive Tanking Membrane (Proofex 3000or similar) installed to manufacture' details and spectication.100mm XPS water resistant rigid insulation as protective layer to face oftanking membrane.
Office Area
ReceptionCafe Area
Basement Car Park
Double glazed window panel with thermal break anodised aluminium frame supplied and installed by Reynaers
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
300 x 300mm reinforced in-situ concrete columns to Engineer's details
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) with EPDM vapour control layer. Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating
Reinforced in-situ concrete basement floor slab to Engineer's details on XPS rigid insulation as void filler on Radon barrier membrane (Monarflex RMB400) lapped and taped at joints to manufacturer's spec on 50mm sand layer on 150mm compacted graded hardcore
Curtain walling glazing and double door system to entrance by Reynaers (CW60)
50mm concrete paving slabs in selected colour and pattern (Tobermore Airclean VS50) with open joins on filter fleece layer on proprietary support drainage board (Bauder DS650) on waterproof membrane on 85mm XPS rigid insulation under paved area1:60 surface drainage fall achieved in structural screed on 200mm precast hollow floor slabs to Engineer's detail
Extension Green Roof Area:Finish growing surface on WB vegitation matting on 100mm Extensive/Biodiverse substrate layer on filteration fleece membrane on water storage/ drainage layer (Bauder DSE20) to fall to boundary edges on polyester/polypropylene fibre protective layer
Reinforced concrete Pile and Pad foundationto engineers specifications.
Office Area
Mineral wool fire stop strip
Cast in-situ reinforce concrete cantilever bean and upstand to Engineer's detail
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
Permeable ground drain connected to surface water drainage sumpprotected to geotech filter layer all bedded in grade water gravel
Proprietry PVC internal day joint Waterbar (Sika PVC-P NB Type A)
Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
EPDM waterproofing layer adhered to concrete elements. EDPM paint to face of concrete structural elements applied in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive & Ultraflex Liquid Waterproofing)
300mm Reinforced in-situ Concrete basement wall to Engineer's Details with a Bitimen Waterproofing Self-adhesive Tanking Membrane (Proofex 3000 or similar) installed to manufacture' details and spectication.100mm XPS water resistant rigid insulation as protective layer to face of tanking membrane.
Permeable ground drain connected to surface water drainage sumpprotected to geotech filter layer all bedded in grade water gravel
Proprietry PVC internal day joint Waterbar (Sika PVC-P NB Type A)
Parapet upstand wrapped with EPDM waterproofing layer to adhered to concretesurface in accordance with supplier's spec, joints lapped and sealed with mineral wool insulation (Rockwool Duo Slab) surroundCement render board (Weber) to inner face with flat roof membrane dressed upPrecast concrete parapet panel by Techrete with stainless steel railing
Mineral wool fire stop strip
Cast in-situ reinforce concrete cantilever bean and upstand to Engineer's detail
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
EPDM waterproofing layer adhered to concrete elements. EDPM paint to face of concrete structural elements applied in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive & Ultraflex Liquid Waterproofing)
Parapet upstand wrapped with EPDM waterproofing layer to adhered to concretesurface in accordance with supplier's spec, joints lapped and sealed with mineral wool insulation (Rockwool Duo Slab) surroundPrecast concrete parapet panel by Techrete with stainless steel railing
Flat roof bitimen capping sheet adhered to reinforced PVC underlayer membrane on PIR tapered foil backed insulation to 1:60 drainage fall on self-adhesive bitumen air & vapour control layer with foil facing (Bauder Thermofol PVC System)75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
PV Solar panels (Activ8) on flat roof mounting brackets supplied and installed by specialist at an incline angle of 35 degrees facing due SouthCabling and Invertor to M&E Engineer's detailsFall prevention cable system by specialist with roofing membrane dress
up under weathering cap profile
Two part flat roof rain water down pipe with roofing membrane dress down and sealed as per manufacturer's details
EPDM waterproofing layer adhered to concrete element in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive) EPDM adhered to soffit with mineral wool slabs mechanically fixed to soffit. Plank & soffit aluminium rainscreen fixed to supporting brackets and carrier rails thru insulation to manufacturer's details
2
04/02 - 232
Sim
Office Area
Office Area
Scale
Checked by
Drawn by
Date
Project number
1 : 50
19/0
3/2
020
12:1
9:3
2
Key Reference Section
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
TU Staff
04/02 - 230
1 : 50
Contiguous Section1
Mineral wool fire stop strip
Cast in-situ reinforce concrete cantilever bean and upstand to Engineer's detail
EPDM waterproofing layer adhered to concrete elements. EDPM paint to face of concrete structural elements applied in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive & Ultraflex Liquid Waterproofing)
Parapet upstand wrapped with EPDM waterproofing layer to adhered to concrete surface in accordance with supplier's spec, joints lapped and sealed with mineral wool insulation (Rockwool Duo Slab) surround Precast concrete parapet panel by Techrete with stainless steel railing
Fall prevention cable system by specialist with roofing membrane dress up under weathering cap profile
Two part flat roof rain water down pipe with roofing membrane dress down and sealed as per manufacturer's details
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
Flat roof bitimen capping sheet adhered to reinforced PVC underlayer membrane on PIR tapered foil backed insulation to 1:60 drainage fall on self-adhesive bitumen air & vapour control layer with foil facing (Bauder Thermofol PVC System)75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Mineral wool fire stop strip
Cast in-situ reinforce concrete cantilever bean and upstand to Engineer's detail
EPDM waterproofing layer adhered to concrete elements. EDPM paint to face of concrete structural elements applied in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive & Ultraflex Liquid Waterproofing)
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
Internal ceiling to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire ratingmineral wool slabs mechanically fixed to concrete element soffit
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
300 x 300mm reinforced in-situ concrete columns to Engineer's details
50mm concrete paving slabs in selected colour and pattern (Tobermore Airclean VS50) with open joins on filter fleece layer on proprietary support drainage board (Bauder DS650) on waterproof membrane on 85mm XPS rigid insulation under paved area1:60 surface drainage fall achieved in structural screed on 200mm precast hollow floor slabs to Engineer's detail
Extension Green Roof Area:Finish growing surface on WB vegitation matting on 100mm Extensive/Biodiverse substrate layer on filteration fleece membrane on water storage/ drainage layer (Bauder DSE20) to fall to boundary edges on polyester/polypropylene fibre protective layer
Parapet upstand wrapped with EPDM waterproofing layer to adhered to concretesurface in accordance with supplier's spec, joints lapped and sealed with mineral wool insulation (Rockwool Duo Slab) surroundCement render board (Weber) to inner face with flat roof membrane dressed upPrecast concrete parapet panel by Techrete with stainless steel railing
Two part flat roof rain water down pipe with roofing membrane dress down and sealed as per manufacturer's details
Flexible mastic sealant to selected colour with2no. ruberised waterbar strips to seal joint
EPDM taped adhered to sealed concrete element anddressed down and out over top of glazed frame. additional DPCstrip over sealed to under side of facade panel
Airtightness tape sealed around window frame and internal partition
Powder coated profiled weather strip and drip sealed with mastic seals
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
Mineral wool fire stop strip
Cast in-situ reinforce concrete cantilever bean and upstand to Engineer's detail
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
Flexible mastic sealant to selected colour with2no. ruberised waterbar strips to seal joint
EPDM taped adhered to sealed concrete element anddressed down and out bottom of facade panel sealed in place
Airtightness tape sealed around window frame and internal partition
Powder coated profiled weather strip and drip sealed with mastic seals
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
Use only proprietary fixings and brackets to inside face of facade. All to manufacturer's details and specification.
PIR insulation strip and selected window board with airtightness tape to glazing frame and sealed joint
2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire ratingmineral wool slabs mechanically fixed to concrete element
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
EPDM adhered to soffit with mineral wool slabs mechanically fixed to soffit. Plank & soffit aluminium rainscreen fixed to supporting brackets and carrier rails thru insulation to manufacturer's details
EPDM waterproofing layer adhered to concrete element in accordance with manufacturer's specification (Giscolene F membrane, Giscos FS-011 Adhesive)
Precast concrete facade panels by Techrete on 200mm non-combustible mineral wool (RockWool Duo Slab) mechanically fixed to concrete face
EDPM paint to face of concrete structural elements applied in accordance with manufacturer's specification (Ultraflex Liquid Waterproofing)
Mineral wool fire stop strip
Cast in-situ reinforce concrete cantilever bean and upstand to Engineer's detail
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
Internal ceiling to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire ratingmineral wool slabs mechanically fixed to concrete element soffit
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
Flexible mastic sealant to selected colour with2no. ruberised waterbar strips to seal joint
EPDM taped adhered to sealed concrete element anddressed down and out over top of glazed frame with additional DPC strip over sealed to under side of facade panel
Airtightness tape sealed around window frame and internal partit ion
Powder coated profiled weather strip and drip sealed with mastic seals
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
Powder coated profiled weather strip and drip sealed with mastic seals
Use only proprietary fixings and brackets to inside face of facade. All to manufacturer's details and specification.
PIR insulation strip and selected window board with airtightness tape to glazing frame and sealed joint
2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire ratingmineral wool slabs mechanically fixed to concrete element
Scale
Checked by
Drawn by
Date
Project number
1 : 10
19/0
3/2
020
12:1
9:3
2
Typical Details
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
TU Staff
04/02 - 231
1 : 10
Flat Roof Parapet Detail1
1 : 10
Roof Terrace Parapet Detail2
1 : 10
Ground Level Entrance Soffit Detail4
1 : 10
Typical Window & Cill Detail3
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
Reinforced in-situ concrete basement floor slab to Engineer's details on XPS rigid insulation as void filler on Radon barrier membrane (Monarflex RMB400) lapped and taped at joints to manufacturer's spec on 50mm sand layer on 150mm compacted graded hardcore
300mm Reinforced in-situ Concrete basement wall to Engineer's Details with a Bitimen Waterproofing Self-adhesive Tanking Membrane (Proofex 3000 or similar) installed to manufacture' details and spectication.100mm XPS water resistant rigid insulation as protective layer to face of tanking membrane.
Permeable ground drain connected to surface water drainage sumpprotected to geotech filter layer all bedded in grade water gravel
Proprietry PVC internal day joint Waterbar (Sika PVC-P NB Type A)
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
Mineral wool fire stop strip
Mild steel facade fixing angles and connections as per precast concrete facade supplier details and Engineer's confirmation
EPDM taped adhered to sealed concrete element anddressed down and out over top of floor upstand with additional DPC strip over sealed to under side of facade panel
Double glazed window panel with thermal break anodised aluminium frame by Reynaers
Powder coated profiled weather strip and drip sealed with mastic seals
Use only proprietary fixings and brackets to inside face of facade. All to manufacturer's details and specification.
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall on waterproof membrane on 400mm reinforced in-situ concrete floor/podium slab to Engineer's details
EDPM dressed down to meet tanking membrane seal at overlap
Powder coated profiled weather strip and drip sealed with mastic seals
Proprietry PVC internal day joint Waterbar (Sika PVC-P NB Type A)
Internal wall face to be 70mm Gyproc "C" aluminium frame stud frame installed to manufacturer's specification with 2 layers of 15mm Gyproc "Fireline" board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Window board with airtightness tape to glazing frame and sealed joint
Curtain walling glazing and double door system to entrance with thermally broken anodised aluminium frame (Reynaers CW60)
75mm concrete paving block in selected colour and pattern (Tobermore Airclean VS50) on 50 -100mm sand bed to provide fall on waterproof membrane on 400mm reinforced in-situ concrete floor/podium slab to Engineer's details
Non-combustible foil faced both side mineral wool slabs mechanically fixed to soffitto manufacturer's details
400mm reinforced in-situ concrete floor/podium slab to Engineer's details with selected floor finish, 50mm cement screed, 80mm PIR insulation to internal side.
Aco drainage slot channels connected to surface water drainage system
Mild steel threshold support bracketwith PIR insulation inserted on site
Waterproofing membrane dressed up and under door threshold with DPC strip dressed into Aco slot drain
Reynaers CW60 curtain walling system. Aluminium frame with double glazed panels. Use only proprietary fixings to structural member. All to manufacturer's details and specification.
EPDM adhered to concrete soffit as per manufacturer's spec
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification
Plank & soffit aluminium rainscreen fixed to supporting brackets and carrier rails thru insulation to manufacturer's details
75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
180mm mineral wool insulation slabs (Rainscreen Duo) mechanically fixed to soffit.
EPDM dressed down with DPC strip to top of frame and airtightness tape to soffit
Proprietry insulated spandral panel
Curtain walling glazing and double door system to entrance with thermally broken anodised aluminium frame (Reynaers CW60)
Mild steel threshold support bracketwith PIR insulation inserted on site
Waterproofing membrane dressed up and under door threshold with DPC strip dressed into Aco slot drain
50mm concrete paving slabs in selected colour and pattern (Tobermore Airclean VS50) with open joins on filter fleece layer on proprietary support drainage board (Bauder DS650) on waterproof membrane on 85mm XPS rigid insulation under paved area1:60 surface drainage fall achieved in structural screed on 200mm precast hollow floor slabs to Engineer's detail
Raised access floor system (Kingspan RM600) with priority pelestals and selected finish 150mm service void fitted to manufacturer's specification on 75mm reinforced structural screed floor on 200mm precast hollowcore floor slabs supported on structural reinforced concrete beams all to Engineer's details
Non-combustible foil faced both side mineral wool slabs mechanically fixed to floor slab soffitto manufacturer's details with 2 layers of 15mm Gyproc "Fireline" ceiling board staggered, taped and slimmed joints to achieve 1 hour fire rating.
Scale
Checked by
Drawn by
Date
Project number
1 : 10
19/0
3/2
020
12:1
9:3
3
Typical Details
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
TU Staff
04/02 - 2321 : 10
Ground Floor to Basement Tanking Detail1 1 : 10
Ground Floor Threshold Detail4
1 : 10
Ground Floor Door Head Detail3
1 : 10
Roof Terrace Threshold Detail2
145
2440
145
2730
125 655 3120 125 1475
5500
125 615 3155 125 1475
5500
1030
2425
1015
4470
125 605 4660 125 1475
6985
125 605 4660 125 1475
6985
Parapet Return Left Long Parapet Short Parapet Parapet Return Right
Bordered Corner RightBordered Regular Glazed PanelBordered Long Glazed PanelBordered Corner Left
Corner Return Long Glazed Panel Regular Glazed Panel Corner Return
Bordered Corner RightBordered Regular Glazed PanelBordered Long Glazed PanelBordered Corner Left
Scale
Checked by
Drawn by
Date
Project number
As indicated
19/0
3/2
020
12:1
9:3
3
Facade Panel Study
TDS2200 02
DT175 02 TDS Concrete
DT175 02
19th March 2020
Aidan McKenna
TU Staff
04/02 - 240
1 : 50
Facade Layout1
1 : 100
Facade 3D Study2
1 : 10
Facade Connection3
PROJECT 2RESEARCH
AIDAN MCKENNA
STARTING OFF
Following the issuing of the project brief I start
to figure out the basic structure, deciding on
structural grids, span distances and
directions, floor slab shapes and levels.
Starting with a basic sketch, then moving onto
a more rigid line drawing with a little more
detail so further decisions can be made.
Using research and knowledge gained
from our previous projects on site
servicing and utilisation, and precast
concrete structural analysis, the process
of developing a building begins.
FAÇADE RESEARCH Using case studies from Detail Magazine I focused in a façade concept. The
building I used as my primary source is a student accommodation block in
Eindhoven, Netherlands. The building is entirely prefabricated using a load-
bearing concrete façade.
KEEP DRAWING Once a façade concept was decided on it was time to figure out how to
adapt it to this projects building form. It took a lot of doodling, sketching
and paper to come up with a workable pattern.
WHAT ABOUT THE SITE?Working out the elevation treatment can’t be done in isolation.
How the build fits and works on the site also needs consideration.
TIME FOR THE DETAILING
Once the basic plans and concepts are in place it’s time to
figuring out how the build is to be constructed.
Considering all the elements, joining them together in a
robust fashion while all the time mindful of guidelines,
standards and regulations. It’s quit a challenge!
Again lots of sketching, drawing and focusing on the
details.
TOP AND TAILConsidering the major details such as the basement and parapet, waterproofing and
insulating is key. Preventing ground water egress into the basement using a tanking
membrane and ground drainage while minimising cold bridging and dampness getting
into the building at the parapet level.
ENTRANCE AND CORE
Designing a layout for the stairs and lift core
was an interesting exercise. Balancing the size
and usability of this area, while considering the
regulations and requirements is quite a
balancing act. I was surprised at how much
area had to be give over.
Entrance thresholds are prone to problems.
Keeping the build’s thermal envelope
continuous at this point, minimising the
likelihood of water coming into the building and
making the threshold robust to handle heavy
footage are all challenges in this area.
SOMEWHERE TO RELAXThe project brief called for a Green Roof terrace for people to step
outside and relax in the fresh air. Dealing with the various building
levels and constraints, whilst providing the appropriate drainage,
thermal and moisture protection meant I couldn’t relax.
AND NOW TO REVITIt is only when you start to model your
project that you appreciate the time spend
sketching and working out the various
elements and details. It’s time well spent.
THE END
I would just like to thank the design studio staff for their guidance, support and feedback.
The library staff and the facility. And Detail Magazine for the inspiration and vagueness.
Aidan McKenna
DT175-2 TECH 2200 Project 2
Recommended