User Manual - trius-audio.de · In general, it is an 8 x 8 digital audio matrix system, which is...

Preview:

Citation preview

R2User Manual

www.audac.eu

2

3

Index Introduction 5

Environment 7

Safety requirements 9 Caution servicing 9

Chapter 1: Pin connections and connectors 11 Attention 11

Chapter 2: Overview front and rear panel 13 Front description 13 Rear description 14 Audio in- and outputs 14 Priority, S/PDIF & Fiber link inputs 14 Peripheral interfaces 15 Control ports 15 Chapter 3: Wire up the system 15

Chapter 4: R2 Quick start guide 16 Connecting the R2 16 Configuring the R2 17 Chapter 5: User interface & configuration 19 Open the user interface 19 Login screen 19 Main screen 20 Zone settings 21 Sound settings 22 Test signals 23 Zone linking 24 Input selection 25 Configuration settings screen 26 Digital input selection 26 Timer settings 27 Time settings 28 Network settings 29 Paging settings 29 Priority settings 30 System configuration 31 R2 Address settings 32 Fiber settings 33 Amplifier bridging 34 Password settings 34 Factory settings 35

4

Lite User Interface 36 Login screen 36 Main screen 36 iPhone + iPad 37 Chapter 6: Peripheral interfaces 38 Wall mounted control panels 39 DW3018/4018 Basic wall panel 39 DW5065 All-in-one wall panel 40 Connection possibilities 41 Chapter 7: Paging 43

Chapter 8: Cascading the R2 46 Principle 48 Fiber audio flow 48 Setting up the project 50 Connection possibilities 39 Chapter 9: Additional information 53 IP Basics 53 Updating the R2 54 Technical specifications 55 Personal notes 56

5

IntroductionMulti-Zone Audio Matrix SystemTheR2isaMulti-Zoneaudiodistributionsystemwhichisatrulypolyvalentsolutionforcommercialandresidentialapplications,withtheflexibilityofamultizonerouter.Itdeliversacomprehensiveandexpandablepowerfulsolutionfornearlyeverysituation.Withitslargenumberofextensionmodulesandconfigurationmodes,itprovidesasolutionforanuncountableamountofinstallations–largeorsmall,simpleorcomplex.

Ingeneral,itisan8x8digitalaudiomatrixsystem,whichisbasedonapowerfulDSPprocessor.Itisfullydigitallycontrollable,andthebuilt-indigitalmatrixmakesitpossibletopatchanyoftheinputsignalstoanyoftheoutputsignals.

Itisstandardequippedwith8analoglineinputsand8analoglineoutputs,buttheflexiblestructureofthedevicemakesiteasytoextendthisnumbertoanappropriatesolutionforeachspecificsituation.

Ifdesired,itiseasytocascademultipleR2’swiththefiberinterconnectionmodules.Thismakesitpossibletotransferupto8stereochannelsandtoextendtoannearlyunlimitednumberofzones.

Butitismuchmorethanthat,duetotheextremelypowerfulDSPprocessor,itprovidesgreaterflexibility,higherreliabilityandlowerlatencythananyotheramplifierofitskind.Moreover,it’scapableofdoingcomplexcalculationsonthedigitalaudiosignals,whichmakesitpossibletointegratedigitalfiltersintothesystemandgeneratecomplexaudiosignals.

Inaddition,areal-timeclockisprovidedwhichmakesitpossibletocreatetimescheduleswithupto256pre-programmedevents,singleandrecurring.

EveryR2isstandardequippedwithanintegratedEthernetcontrolinterfacewhichmakesitpossibletoconfigureandcontroltheR2fromanyPC,laptoporPDAwhichisconnectedtotheinternet.Justuseyourbrowser,gototheappropriatewebsiteandyouhavecompletecontroloftheR2.

Anoptionaltouchscreencanbeinstalledinthefrontoftheamplifierandthereareoptionalwallcontrolpanelswherebythedesiredmusicsourceandvolumecanbeselectedforaspecificzone.

AnRS232interfaceisprovidedforconfigurationandcontrolwithperipheralsfromothermanufacturerswhichmakeuseofanRS232connection,likeAMX,Crestron,…thecontrolcommandsarefreelyavailablewhichmakesiteasytodevelopspecificapplicationsthatworkincombinationwiththeR2.

6

7

Environment

Donotplacethisunitinanenclosedenvironmentsuchasabookshelforcloset.Ensurethereisadequateventilationtocooltheunit.Donotblocktheventilationopenings.

Donotplacetheunitinenvironmentswhichcontainhighlevelsofdust,heat,moistureorvibration.

Donotusetheunitnearwaterorotherliquids.Makesurenowaterorotherliquidscanbespilled,drippedorsplashedontheunit.

Theunitisdevelopedforindooruseonly.Donotuseitoutdoors.

Donotplaceobjects(books,vases,…)ontopoftheunit.

Placetheunitonastablebaseormountitinastablerack.

8

9

Safety requirements

Alwayshandletheunitwithcare.

Onlyuseagroundedsocketoutletandapowercordwithgroundingplugtoplugintheunit.

Thisunitisnotatoy.Itshouldnotbeoperatedbychildren.

DonotstickobjectsthroughtheventilationopeningsoftheR2.

Donotopentheunit.(riskforelectricalshock)

TheR2containsseveral‘jumpers’whichcanbeset.Thesesettingsmayonlybedonebyqualifiedpeople.

CAUTION - SERVICING

Thisunitcontainsnouserserviceableparts.Referallservicingto qualifiedservicepersonnel.Donotperformanyservicingunless youarequalifiedtodoso.

NOTE

This produc t conforms to the fo l lowing European S tandards:EN50081-1:1992,EN50082-1:1992,EN60065:1994

10

11

Chapter 1Pin connections and connectors

Cinch (RCA):Forlineinputconnections

Tip= Signal Sleeve= Ground White=Left Red= Right

RJ45 (RS485, Digital Audio, +24V DC): ForconnectiontoWallPanels

Pin 1 White-Orange AUDIOTXA Pin 2 Orange AUDIOTXB Pin 3 White-Green +24VDC Pin 4 Blue RS485A Pin 5 White-Blue RS485B Pin 6 Green GND Pin 7 White-Brown AUDIORXA Pin 8 Brown AUDIORXB

ATTENTION

Thetwistedpaircablingmustalwaysbe‘straight’.Incaseofself madecabling,itmustbewiredasdescribedabove,tomakethe systemworkproperly.

RS232 (serial connection interface): Forconnectionwithhomeautomationsystems,orotherremotecontrolequipment

Connection StandardRS232 PIN 2 R2TX PIN 3 R2RX PIN 5 GND

Settings 19200Baud 8Bit 1Stopbit Noparity NoHandshaking

RS232 / RS485 / TCP/IP

TheR2amplifierhasRS232,RS485andTCP/IPportswhichallacceptthesamecommands.ThecompletecommandsettocontroltheR2amplifierisavailableintheR2commandsusermanualwhichisfreelyavailableonwww.audac.eu/download.

12

13

Chapter 2Overview front & rear panel

R2

OnthefrontoftheR2amplifierareapowerbutton,fourUSBconnectionportsspaceforanoptionaltouchscreen(R2DIS)provided.

Thepowerbuttonisalatchingtypeandshouldbeusedforpowering-upthesystem.Whenthepowerbuttonispressed,theR2willstartup.Whenthestartupprocedureistakingplace,theLEDonfrontoftheamplifierwillblinkblue.Afterthestartupprocedureiscompleted,theLEDwilllight-upblue,andtheR2willbereadyforoperation.

Therectangularareaonthefrontoftheamplifieristhelocationwheretheoptionaltouchscreenshouldbeinstalled(R2DIS).ThistouchscreencanbeusedforcontrollingandconfiguringallthefunctionsoftheR2amplifier.Thisunitconsistsofa7”touchscreenwithaformatof16/9andaresolutionof800x480px.Asmallintegratedcomputercontrolsthefunctionsofthetouchscreen.

ThelowerUSBconnectionportonfrontoftheamplifierisdedicatedforsoftwareupdates.Whenthetouchscreenisinstalled,theotherthreeUSBconnectionscanbeusedtoconnectseveralperipheralstotheamplifierlikeanUSBkeyboardormouse.

Whentheoptionaltouchscreenisnotinstalledandthelowerusbconnectionisconnectedtoyourpc,theotherthreeUSBportsactasahubtoyourcomputer.TheperipheralsconnectedtotheUSBportswillbeconnectedtoyourPC.

Front

14

8linelevelin-andoutputsareprovidedinitsstandardconfiguration.EachlineinputisfittedwithstereoRCAinputconnectorsandaclippingLEDwhichilluminateswhenthesignalreachestheclippinglevel.Bymeansofthegaincontrolpotentiometers,theleveloftheinputsignalscanbecontrolled.

EachzoneoutputisfittedwithRCAstereoconnectorsfortheconnectionofexternalamplifiers.Whentheoptionalpoweramplifierkitisinstalled(R2POW),eachoutputzonehasanamplifiedstereowithapowerof2x40Watt@4Ohmor2x20Watt@8Ohm.Theamplifiedzoneoutputscanbebridgedinthegraphicaluserinterfacetoobtainapowerof80Watt@8Ohmforeachoutputzone.

Audio in- and outputs

Priority, S/PDIF & FiberTwoaudiopriorityinputsandtwoprioritycontactinputsprovided.Dependingoftheconfiguration,4prioritysignalscanbeused.Theactionsthatneedtohappenwhenaprioritysignaloccurscanbefreelyprogrammed.Therecanbeautomaticallyswitchedtothepriorityaudioinputswhenaaudiosignalisapplied,ortheinternalroutingcanbeadaptedwhenasignalisavailableonthecontactinputs.

AdigitalS/PDIFin-andoutputconnectionisprovided,whichisbothcoaxialandopticalimplemented.Thedigitalinputsignalscanberoutedjustliketheanaloginputstothedesiredoutputzone.Thedigitaloutputscanbeprogrammedinawaythatthereisafreelyselectablezoneoutputavailableonthischannel,withoutavolumecontrol.Thiscanbeusefulformakinglosslessrecordings.

Thelinkin-andoutputsareopticalfiberconnectorswhichcanbeusedforcascadingmultipleR2’s.Forthisfeature,theoptionalfiberinterconnectionmodulehastobeinstalled.

Rear

15

Peripheral interfaces

10RJ45connectorsforexpansionwithadditionalwallpanelsandin-andoutputmodulesareprovided.AlltheseconnectorscarryRS485signals.Thisallowsthecontroloftheamplifierfrom10differentlocations.

8oftheseconnectorsareabletocarrydigitalaudiosignals(PI1toPI8)forexpansionwithadditionalwalllineinputunits.

TheRJ45remotecontrolinputshouldbeconnectedtoaLANnetwork.ThismakesitpossibletocontroltheR2systemoverEthernet,bymeansofaweb-browseroranyotherdevicesupportingEthernet.

TheRS232connectioncanbeusedtocontroltheR2withexternalcontrolequipmentsupportingRS232.ThisallowstocoupletheR2withyourhomeautomationsystem,andcontrolitthroughhardwareofothermanufacturers,likeAMX,Crestron,….

Control ports

Chapter 3Wire up the systemThewiringofthesystemmustbedoneaccordingtothefollowingrules,toguaranteeaproperfunctioningofthesysteminallcircumstances.

1. Speakercableforamplifiedzoneoutputs:minimum2x1.5mm² (distance>15m:2x2.5mm²)

2. WallMountedInput&Controlunits: DW3018/4018 UTP/FTPCat5cableorbetter DW5065 UTP/FTPCat6cableorbetter APM UTP/FTPCat6cableorbetter3. Musicsourcesandlinelevelzoneoutputs:mustbeconnectedwithhighqualityaudiocableand connectors.

4. Ethernetconnection:UTP/FTPCat5cableorbetter

16

Chapter 4R2 Quick start guide

This chapter guides you through the setup process of a basic project with one R2 audio matrix and 8 standard DW3018/4018 wall panels.

Overview of the R2 setup

Connecting the R21) Connecting audio sources Connectallyouraudiosources(CD-players,tuners,...)tothelineinputs(RCAconnectors)ontherearpaneloftheR2.Adjustallinputgainstotheappropriatelevelsonoclippingoccurs.

2) Connecting amplifiers and/or speakersConnectamplifiers(100Vorlowimpedance)tothelineoutputs(RCAconnectors)ontherearpaneloftheR2.Whentheoptionalpoweramplifierkitisinstalled,lowimpedanceloudspeakerscanbeconnectedtotheloudspeakeroutputs(Euro-Terminalblockconnectors)ontherearsideoftheR2.

3) Connecting wall panels ConnecttheDW3018/4018wallpanelstothePI(PeripheralInterface)inputs(RJ45connectors)onrearpaneloftheR2.MultipleDW3018/4018wallpanelscanbeconnectedtoonesinglePIinputbyusingbuscabling(connectingallthewallpanelsinparallel),oreachwallpanelcanbeconnectedtoanPIinputbyaseparatecable.Itdoesn’tmatterwhichPIportisusedforwhichzone,thesettingsforwhichwallpanelshouldcontrolwhichzonecanbemadeintheuserinterface.

4) Connecting a computerAcomputercanbeconnectedtotheR2throughtrueethernet.IfthecomputerisdirectlyconnectedtotheR2,acrossednetworkcableisnecessary.IftheR2isconnectedtoalocalLANnetwork(connectedtoarouter/switch/hub)astraightnetworkcableisnecessary.AskyourITadministratorforhelp.Togetaccesstotheuserinterface,enterthefollowingaddressinyourinternetbrowseraddressbar:“http://192.168.0.191”(ThisisthefactorydefaultIPaddressoftheR2,canbechangedintheuserinterface).Thedefaultadministratorpassword(givesyouaccesstoallfunctions)is“R2”andthedefaultuserpassword(givesyouonlyaccesstothebasicfunctions)is“user”.Ifyouwanttomakeanychangestothesettings,youshouldlog-inwiththeadministratorpassword.

Prog.

Vol+

-

+

-Prog.

Vol+

-

+

-Prog.

Vol+

-

+

-Prog.

Vol+

-

+

-Prog.

Vol+

-

+

-Prog.

Vol+

-

+

-Prog.

Vol+

-

+

-Prog.

Vol+

-

+

- Audiosources

Amplifiers

Wallpanels

17

Configuring the R21) Changing the IP address YoucanskipthisstepwhenthedefaultIPaddress“192.168.0.191”isnotusedbyanotherdeviceinyournetwork,andisOKforyou.IfyouliketochangetheIPaddress,gotothe“Setup”menu(clicktheiconintheupperrightcornerofthemainscreen)andclick“NetworkSettings”.NowyoucanchangetheIPaddress,andclick“OK”toapplythechangesandsave.Afterwards,yourbrowserwillbeautomaticallyredirectedtothenewIPaddressoftheR2,andthedefaultIPaddressisnotlongervalid.

2) Changing the passwordYoucanskipthisstepifthedefaultpassword“R2”foradministratorand“user”forusersisOKforyou,buywealwaysrecommendtochangethesepasswords,especiallywhenyourR2isconnectedtoapublicnetworkwhereexternalusershaveaccessto.Ifyouliketochangethepassword,gotothe“Setup”menuandclick“Passwordsettings”.Hereyoucanchangethepasswords.First,theoldpasswordneedstobeentered,andsubsequentlythenewpasswordneedstobeenteredtwice(Max10characters).Pressthe“OK”buttontosavethenewpassword.Now,youalwaysneedtolog-inwiththenewpasswordsandthedefaultpasswordsarenotlongervalid.

3) Configuring wall panels and sources Gotothe“Setup”menuandclick“Systemconfiguration”.Nowyouhavethepossibilitytochoosebetween“Paging”,“DW5065”and“DW3018/4018”.ToconfigurethesettingsfortheDW3018/4018wallpanels,clickthecorrespondingbutton.Bythedropdownlistontheleftside,youcanchooseforwhichzoneyouwanttoconfigureawallpanel.Afterthedesiredzoneisselected,youcanassignoneoftheconnectedwallpanelswiththatparticularzonebyclicking“SetAddress”.Thedisplaysonallwallpanelswillstartblinkingwiththeselectedzonenumber.Pushthe“Program+”buttononthewallpanelifyouwanttoassignthatparticularwallpanelwiththeselectedzone.Afterthe“Program+”buttonispressed,thewallpanelwillbelinkedwiththeselectedzone,andthedisplaywillstopblinking.

TheR2containsmanydifferentinputswhichcanbeselectedtolinkwithazone.8ofthoseinputsareaccessiblethroughthe“Quickmenu”(dropdownlistonthemainpage).Thesameinputswhichareavailableinthe“Quickmenu”canbeselectedontheDW3018/4018wallpanels.Theotherinputsareaccessiblethroughthesettingsmenuifyouarelogged-inasadministrator.Youcanchoosetheinputswhichareselectableinthe“Quickmenu”andwiththeDW3018/4018wallpanelsthroughthe“Inputselection”menuinthe“ZoneSettings”window(Standardarelineinputs1to8selected).Simplyselectthedesiredinputsignalsbythedropdownlistsonthecorrespondinglocation.Afterthedesiredinputchannelsareselected,clickthe“Setinputs”buttontosavethechanges.Theselectedinputsarenowselectableinthe“Quickmenu”andbymeansofthewallpanel.

ReadyYoursystemisnowreadyforusewiththewallpanels.

18

19

Chapter 5User interface & configurationTogetaccesstothecontrolandconfigurationsettings,theR2shouldbeconnectedtoacomputeroranEthernetLANnetwork.Formoreinformationaboutnetworkconnectionsandsettings,seeIPbasicsinchapter8.

Thestandard(factorydefault)IPaddressoftheR2is192.168.0.191,makesurethisaddressiswithintheIPrangeoftheconnectedEthernetLANnetwork(subnetmask255.255.255.0).IfthedefaultnetworkaddressisnotwithinrangeofyourLANnetwork,contactyournetworkspecialist.ThenetworkaddresscanbechangedwiththeStandardWebBasedUserInterfacebutthereforeanetworkconnectionhastobemadefirst!

Anydevice(PC,Laptop,PDAorevenaSmartphone)withawebbrowserandtheMacromediaFlash8.0plug-in(orhigher)installed,canbeusedtocontrolthewebbaseduserinterface.

Formobiledevices,suchasPDA’s,smartphonesoreveniPhonesoriPads,specialapplicationsaredevelopedtocontrolthestandardfunctionsoftheR2Matrix.

Open the user interface Start your default web browser and enter in the address bar the IP address of the embedded web server of the R2. (The factory default IP address is http://192.168.0.191).

If multiple R2’s are cascased with each other through the fiber interconnection interface, first a selection screen will be displayed whereby the R2 should be selected which you want to control.

Login screenFirsttheloginscreenwillbedisplayed.ApasswordshouldbeenteredtogetaccesstothewebinterfaceoftheR2amplifier.Therearetwodifferentaccesslevels,administratorlevelanduserlevel.

Ifyoulog-inusingtheadministratorpassword,yougetaccesstoallfunctionsandconfigurationoptionsoftheR2Amplifier(Thefactorydefaultpasswordforadministratoraccesis“R2”).

Whenyoulog-inusingtheuser password,youonlygetaccesstothebasicfunctionsoftheR2Amplifier,suchaschangingthevolumeandchangingtheroutingforaparticularoutputzone.(Thefactorydefaultpasswordforuseraccesis“user”).

Aftertherightpasswordisentered,clickthe“OK”button,andyouwillberedirectedtothemainscreenoftheR2interface.

NOTE

ThepasswordscanbechangedintheConfiguration>>Passwordsettingsmenu(Onlyadministrator)

20

Main screenThemainscreendisplaysall8outputzonesoftheR2withfadervolumecontrols.

Volume control Thevolumeofeachchannelcanbesetbymovingthefaderofthecorrespondingchannelupordown.Atthetopandbottomsideofeachfaderisabuttonwithanarrowdisplayedwherebythevolumecanberaisedorloweredinstepsof1dB.Atthebottomisa“Mute”buttonprovidedwhichmutesthevolumeofthecorrespondingoutputchannelinoneclick.Afterthevolumeismuted,thismutebuttonwillbecomeRed,andthevolumecanbeunmutedafterclickingitagain.

Assign zone names Forabetteroverviewofalloutputchannels,everyfadercanbeassignedbyaspecificzonenameasshownintheexamplebelow.Thenameofthezonecanbechangedbydoubleclickingonthenamewhichisdisplayedabovethecorrespondingfader(indicatedinthepicturebelowwith“ZoneName”).Whenacursorcomesup,removetheexistingnamewiththebackspacekey,andjustchangethenameinthedesiredname.Clickonthe“SaveZoneSettings”buttonandconfirmtosavethechangedzonesettings.Thenameofthecorrespondingzonewillbechanged,andnexttimeyoulogintothewebbaseduserinterfaceoftheR2thesamezonenamewillbedisplayed.

Connection statusInthetopleftcornerofthewindowisthe“ConnectionStatus”displayed.TohavecommunicationwiththeR2,theconnectionstatusmustbe“ONLINE”.

Input channel selectionThedesiredinputsignalforaparticularzonecanbeselectedbyusingthedropdownlistboxbelowthezonename.Thisdropdownlistshows8audioinputsignalswhichareselectedasstandardinputsinthe“SystemConfiguration”menu,togetherwiththenoptions“Off”and“Other”.Whennoinputsignalisselected,theoption“Off”willappear.Whenaspecialinputneedtobeselectedwhichisnotselectedasoneofthe8standardinputsinthe“SystemConfiguration”menu,thisshouldbedonebymeansofthe“Settings”menu,whichcanbeobtainedbyclickingthe“Settings”buttonbelowthe“InputSelection”dropdownlist.Inthiscase,theoption“Other”willappear.Inthe“Settings”menu,othersettingssuchastonecontrolordigitalfiltersettingscanbemadetoo.

Configuration menuInthetoprightcornerisa“Setup”buttondisplayed.Afterclickingthisbutton,youwillberedirectedtothegeneralconfigurationmenuoftheR2.

Main screen

21

Zone settingsAfterclickingona“Settings”button,displayedbyafaderofaspecificzone,youwillberedirectedtothe“ZoneSettings”window.Thiswindowgivesanoverviewofallthesettingsthatcanbeappliedtoonespecificzone.

Input channel selectionThefirstwindowgivesanoverviewofallinputchannelswhichcanbepatchedtothatparticularoutputzone.Thefirstdisplayedoptionis‘NoInput”,whichmeanswhenthisoptionisselected,noinputsignalwillberoutedtothatparticularoutputzone.AtthesamelevelistheS/PDIFselectionbuttondisplayed.Whenthisbuttonisselected,thedigitalS/PDIFinputwhichisbothopticalandcoaxialprovided,willberoutedtothatparticularoutputzone.(Theselectionbetweentheopticalorcoaxialinputshouldbemadeinthe“SetupMenu”under“DigitalInputSettings”)Belowarefromlefttorightthe“Cinchinputs”,the“Wallinputs”andthe“Fiberinputs”displayed.The“CinchInputs”arethedirectlineinputswhichareprovidedontherearpaneloftheR2bymeansofRCAconnectors.Inthesecondtablearethe“WallInputs”displayed.Thesearealladditionalinputsignals(LineorMicrophone)whichareconnectedtoanoptionalwallinputunitbymeansoftheperipheralRJ45inputsontherearsideoftheR2.Inthethirdtablearethe“FiberInputs”displayed(OnlyfunctionalwhentheoptionalR2OPTmoduleisinstalled).Thesearethedigitalaudiochannelswhicharetransferredoverthefiberinterconnectioninterface,andcanbepatchedtotheselectedoutputzone.

Toselectthedesiredaudioinputsourcewhichhastobepatchedwiththeselectedoutputchannel,simplyclickthebuttonnexttothedesiredinputsource.TheselectedinputsignalwillbeindicatedinGreen.

Atthebottomofthiswindow,fouradditionalselectionbuttons“SoundSettings”,“TestSignals”,“ZoneLinking”and“Inputselection”aredisplayed.Inthe“SoundSettings”menu,specificconfigurationsettingssuchasapplyingadigitalfilterortonecontrolcanbemade.Inthe“TestSignals”menucanbeselectedwhichkindoftestsignalshouldbepatchedtotheparticularoutputzone.Inthe“Zonelinking”menucanbesetwhichzonesshouldbelinkedwitheachotherandinthe“Inputselection”menucanbeselectedwhichinputsignalsshouldbeshownintheinputpresetmenu.

BackClickthe“Back”buttontogobacktothemainwindow.

Save zone settings TomakesurethechangedzonesettingsarestilleffectiveaftershutdownandrestartoftheR2,the“Save”buttononthemainscreenoftheR2needtobepressed.Atthesametime,thevolumeandroutingsettingswillbesaved.

Zone settings

22

Zone settings >> Sound settingsThe“SoundSettings”windowoffersthepossibilitytoapplyadigitalfiltertotheselectedoutputzone,andtoadjustthesoundsettingsbymeansofthetwo-bandtonecontrol.

Digital FilterToapplyafiltertotheselectedoutputzone,tickthe“EnableFilter”checkboxandselectthedesiredfiltertypebetweenHigh-Pass,Low-PassandBand-Pass.WithaHigh-Passfilter,thefrequenciesbelowthecrossoverfrequencywillbesupressed,withaLow-Passfilter,thefrequenciesabovethecrossoverfrequencywillbesupressed,andwithaBand-Passfilter,thefrequencieshigherthantheuppercrossoverpoint,andbelowthelowercrossoverpointwillbesupressed.

Afterthedesiredfiltertypeisselected,theslide-barstoadjustthecrossoverfrequencieswillbedisplayed.Thecrossoverfrequencycanbeadjustedbyslidingthebuttononthesliderscaletotheleftandtheright.Thefrequencycanbesetbetween10Hzand22kHz,andtheexactsetcrossoverfrequencyisdisplayedontherightsideofthesliderscale.

Two band tone controlAlongthefiltersetings,twofadersdisplayedontherightsidewhicharemeanttoadjustthesoundsettingsthroughtwo-bandtonecontrol.Theleftmostfaderindicatedwith“Bass”offersthepossibilitytoadjustthelevelofthelowfrequencies,whiletherightmostfaderindicatedwith“Treble”offersthepossibilitytoadjustthelevelofthehighfrequencies.Thesoundlevellevelforbothlowandhightonescanamplifiedorattenuatedbetween+9dBand-9dB.Thiscanbeeasilydonebyslidingthefadersupanddowninthesamewayasthevolumecontrolonthemainscreen.

BackClickthe“Back”buttontogobacktothepreviouswindow.

Sound settings

23

Zone settings >> Test signalsThetestsignalswindowgivesanoverviewofallspecialinputsignalswhichcanbepatchedtotheselectedoutputzone.TheR2hasaninternaldigitalsignalgeneratorwhichcangeneratewhitenoise,pinknoiseandsinusoidalsignalswithaselectablefrequency.Eachofthosesignalscanbepatchedtoanyoutputzone.

Signal SelectionForpatchingthosesignalstotheselectedoutputzone,simplyclickthebuttonwhichisdisplayednexttothedesiredsignal,andtheselectionbuttonwillbecomegreenwhenthesignalisselected.

Whenthe“SineGenerator”isselected,theoutputfrequencyofthegeneratorcanbeadjustedbyclickingtheupanddownarrowsdisplayednexttotheselectedfrequency.

Whenoneofthetestsignalsisselected,“Other”willappearinthe‘InputSelection”boxonthemainscreen.

BackClickthe“Back”buttontogobacktothepreviouswindow.

Test signals

24

Zone settings >> Zone linkingThe“ZoneLinking”windowoffersthepossibilitytolinkseveralzoneswitheachother,makingthezonesettingslikevolumeandroutingcoupledwitheachother.Thereisthepossibilitytomakeapermanentlinkingoralinkingundercertainconditions(prioritycontact)betweenthedifferentzones.

LinkingAllzoneswhichcanbelinkedtotheselectedoutputzoneareshowninalistunderneatheachother.Nexttoeachzonename,adropdownlistisshownwherebythelinkingcanbeselected.Thestandardsettingissetto“Notlinked”,andthelinkingmethodcanbeselectedbetween“LinkedbyPriocontact1”,“LinkedbyPriocontact2”,and“FixedLinked”.

Whenseveralzonesarelinkedwitheachotherandanychangeismadetothevolumeorroutingsettingsfromoneofthelinkedzones,theotherlinkedzoneswillautomaticallyfollowthesamechangesmadetothesettings.

Linked by priority contact Whenthe“LinkedbyPriocontact1”or“Linkedbypriocontact2”optionsareselected,thezoneswillbelinkedwitheachotherwhenaconnectionismadebetweentheprioritycontactswhichareprovidedontherearsideoftheR2.Thelinkingbetweenthezoneswillremainaslongasthecontactisestablished.Forexample,thiscanbedonebymeansofaswitchorrelay.

Fixed Linked Whenthe‘FixedLinked”optionisselected,thelinkingbetweenthezoneswillbepermanentlypresent.

Slave Whenazonealreadyislinkedwithanotherzone,thelinkedzonewillbecalledthe“Slave”fromthe“Master”zoneandthelinkingsettingsforthiszonewillbeunavailable.Whenselectingthe“ZoneLinking”forthiszone,themessage“Zoneisalreadyslaveofanotherzone”willappear.

BackClickthe“Back”buttontogobacktothepreviouswindow.

Zone linking

25

Zone settings >> Input selectionThe“InputSelection”windowallowsyoutomakeaselectionoutofallavailableinputsignalsforthe“QuickSelectionMenu”.Thisisdisplayedonthemainscreenjustbelowthezonename.Itisconvenienttoaddthe8commonusedandmostimportantinputsignalstothe“QuickSelectionMenu”.

Moreover,theinputsignalsselectedinthismenuarealsothe8signalswhichareselectablebytheDW3018/4018wallpanelslinkedwiththiszone.

SelectionThiswindowgivesanoverviewof8listboxes,eachcorrespondingwithanumberfrom1to8.Whenclickingthislistbox,allinputsignalpossibilitieswillbeshown,rangingfromthedirectlineinputstothefiberandwallpanelinputsaswellastheinternaltestsignals.Afterthe8inputsareselected,clickthe‘Setinputs’buttonandtheselectedinputswillbeassignedwiththiszone.

BackClickthe“Back”buttontogobacktothepreviouswindow.

Input selection

26

Configuration settings screenTheconfigurationsettingscontrolpanelcomesupafterclickingthe“Setup”button.Thisbuttonisalwaysshownintheupperrightcornerofeverywindow.(OnlyonAdministratorlevel)

Inthiswindow,allthesettingsoftheR2canbemade,suchasselectingthedesireddigitalinputsource,changingthetimesettings,configuringthebuilt-intimer,adjustingthenetworksettings,adjustingthepagingvolume,changingtheprioritysettings,makingthesystemconfigurationforexternalconnecteddevices,makingthefibersettings,settingtheaddress,bridgingtheoutputchannels,changingthepassword,andrestoringthesettingstofactorydefault.

Ifyouwanttochangesomesettings,justclickonthecorrespondingicon.

Save configuration Allconfigurationsettingschangesmadeinthiswindowwillbesavedautomaticallyandarestilleffectiveaftershutdownofthedevice.

BackClickthe“Back”buttontogobacktothemainscreen.

Settings

Settings >> Digital input selectionThedesireddigitalS/PDIFaudioinputcanbeselectedinthiswindow.

TheS/PDIFinputisbothco-axialimplementedwithanRCAconnectoraswellasopticalimplementedwithaToslinkconnector.

Theselectedinputsignalwillbepatchedtothedigitalaudiointerface,andwillbepatchedtoanoutputzonewhenitisselectedinthe“ExtraInputs”menuoftheoutputchannelsettings.

BackClickthe“Back”buttontogobacktotheconfigurationscreen.DDR2 Digital Input Settings

27

Digital Input Settings

Settings >> Timer SettingsUp to 256 pre-programmed timer presets can be made in the “Timer Settings” window.Therecanbechosenforbothchangingthesignalrouting,oradjustingofthesignalvolumeatpre-programmedmoments.Theactionwhichneedstobeperformedshouldbeselectedbymeansofthe“ACTION”dropdownlist.Tosetaneventatapre-programmedmoment,youneedtopassthroughthe“TimerSettings”window.

Change RoutingTochangetheroutingofasignalatapre-programmedmoment,select“Routing”inthe“ACTION”dropdownlist,andselecttheinputsignalinthe“INPUT”dropdownlist.Theinputdropdownlistshowsallthedirect“CINCHINPUTS”aswellastheadditional“WALLINPUTS”,(optional)“FIBERINPUTS”andspecial“TESTINPUTS”.Bymeansoftheselectionbuttonsnexttothedropdownlist,theoutputchannelswhichshouldbeaffectedbytheactioncanbeselected.Theoutputchannelscanbeselectedthroughclickingtheselectionbuttons.Theircolorwillchangetogreenwhentheyareselected.

Change VolumeForchangingtheoutputvolumeofazoneatpre-programmedmoments,select“Volume”inthe“ACTION”dropdownlist.TheamountofdB’swherebythevolumeshouldbereducedcanbeselected.Thezoneoutputwherethevolumeadjustneedstotakeeffectoncanbeselectedbyclickingthemonandoffbythe“OUTPUTS”section.

Single and recurringTherecanbeprogrammedsingleeventsthatonlyhappenonce,buttherecanalsobeprogrammedrecurringeventsthatrepeatonaweeklybasis.Thiscanbeselectedbytogglingtheselectionboxbetween“Day”and“Date”.Forsingleeventswechoose“Date”,andthenselectthedesiredtimeanddatebythedropdownlists.Forrecurringevents,clickonthecheckboxesforthedaysoftheweekwhentheeventhastotakeplace,andfillthedesiredtimeinthedropdownlists.

Toaddthesetactionstothetimeschedule,clickthe“Add”buttonandtheprogrammedactionwillappearinthe“ACTIONS”windowbelow.

Forchangingtheevents,clickontheeventwhichshouldbeadjustedinthe“ACTIONS”window.Afterthedesiredactionisselected,clickthe“Edit”buttonontherightsideofthewindow,andtheactioncanbechanged.BackClickthe“Back”buttontogobacktotheconfigurationscreen.

28

Timer settings

Settings >> Time settingsTheactualtimeanddateoftheR2canbesetinthiswindow.

Thiscanbedoneontwodifferentways,theclocksettingscanbemademanuallybyselectingtherightvaluesfromadropdownlist,orwhenconnectedtotheinternet,thecurrenttimeanddatecanberetrievedfromatimeserver.Justselectthetimezoneinwhichyouarelocated,andthecurrenttimeanddateisautomaticallyupdatedbythetimeserver.

Clickthe“OK”buttontoconfirmthetimesettings.

Time Settings

29

Settings >> Network settingsInthiswindow,thenetworksettingsoftheR2canbeadjusted.TheIPaddresscanbesetmanuallyorcanbeautomaticallyassignedbyaDHCPserver.

TheIPaddressisstandardsetto192.168.0.191andthesubnetmaskisstandardsetto255.255.255.0.

Be aware:WhenaDHCPserverisusedinthenetwork,andtheDHCPfunctionoftheR2isenabled,theDHCPserverautomaticallyassignsanIPaddresstotheR2.

InsomecasesthiscancauseproblemsbecausetheIPaddressisnotalwaysknownfortheuser,andtheIPaddressisrequiredtoaccessthewebbaseduserinterface.Ifyoudon’tknowtheIPaddress,theR2willbelostinyournetwork.

Oneadditionalproblemisthat,whentheR2bootsthenexttime,theIPaddressthattheDHCPserverassignscanbedifferent.

Clickthe“OK”buttontoconfirmthenetworksettings.

Network Settings

Settings >> Paging settingsInthiswindow,thepagingvolumeforeachindividualzonecanbesetbymeansofthedropdownboxesdisplayednexttothezonenames.Thepagingvolumecanbesetinstepsof-1dB,startingby0dB,goingto-∞.Whenthevolumeissetto0dB,announcementsforthecorrespondingzoneswillbemadeonmaxiumvolume.

BackClickthe“Back”buttontogobacktotheconfigurationscreen.

30

Paging Settings

Settings >> Priority settingsTheprioritysettingsmenumakesitpossibletoconfiguretheprioritychannels.Ontopofthiswindow,allpriorityinputsaredisplayedrangingfromPriority1toPriority4.

Priority input selectionYoucanselectthedesiredprioritychannelbyclickingonthecorrespondingbuttonontopofthewindow,andswitchingthemonandoffcanbedonebyclickingthe“Enabled”button.Whenthepriorityisenabled,thisbuttonwillturngreen.

Ontheleftsideofthiswindow,therearea“Trigger”anda“Input”dropdownlistdisplayed.Inthe“Trigger”dropdownlistarealltheinputsshownonwhichtheprioritycanbetriggered.Thisrangesfromthedirectlineinputstothefiberandwallpanelinputsaswellastheinternaltestsignals.Inadditiontotheseinputsignalsfourpriorityinputsaredisplayed(twoprioritysignalinputsandtwoprioritycontactinputs).Hereyoucanselectonwhichinputsignalthepriorityneedstobetriggered.Whenanpriorityaudioinputisselected,therewillbeswitchedtoprioritywhenanaudiosignalispresentontheseinputs.Whenacontactinputisselected,therewillbeswitchedtoprioritywhenacontactismadebetweenthosetwopins.

Inthe“Input”dropdownlistbelow,therecanbeselectedwhichinputsignalhastobepatchedwhenaprioritysituationoccurs.Inthislist,thetwodirectpriorityaudioinputs,theregulardirectRCAinputs,theWallpanelinputs,theFiberinputs,butalsotheDSPandotherinputsignalsaredisplayed.

Ontherightsideofthewindowisalistofalloutputchannelsdisplayed.Inthislistcanbeselectedtowhichoutputzonestheprioritychannelneedstobepatched.Thiscanbedonebysimplyclickingthebuttonnexttothechannel.Whentheprioritysignalforthiszoneisenabled,thebuttonwillturngreen.

Nexttoeveryoutputzoneisadropdownlistdisplayedwherebythevolumecanbeselectedinstepsof-1dB.

TheswitchingtoandfromaprioritysignalisdoneaccordingtotheHARDIN - FADEOUT principle.Thismeanswhenaprioritysituationoccurs(signalpresentonthepriorityaudioinputsorconnectionbetweenpriorityinputcontacts),immediatelywillbeswitchedtotheselectedpriorityaction.Whentheprioritysituationisover(nomoresignalpresentonthepriorityaudioinputsornomoreconnectionbetweenthepriorityinputcontacts),thestatusoftheR2willreturntothepreviousstatusbyfadingthesoundin.

Clickthe“OK”buttontoconfirmtheprioritysettings.

31

Priority Settings

Settings >> System configurationInthiswindow,theconfigurationsettingsforexternalconnecteddevicessuchaspagingconsolesandwallpanelscanbemade.Thiswindowshowsthreebuttons,eachofthemforconfiguringonekindofexternalconnecteddevices.Clickthe‘Paging’buttonwhentheconfigurationfortheAPM1xxpagingconsoleshastobemade,whilethe‘DW5065’buttonenablestoconfigurethesettingsfortheAll-in-onewallpanels,andthe‘DW3018/4018’enablesyoutoconfigurethesettingsforthebasicwallpanels.

Justclickthecorrespondingbuttontoproceedtothesettingsmenu.

Formoreinfiormationabouttheconnectionandconfigurationpossibilitiesforexternalconnecteddevices,refertoChapter 6: Peripheral Interfacesofthisusermanual.Inthischapterisextensivelydescribedhowtheconnectionandconfigurationforperipheralequipmentshouldbedone.

Back Clickthe“Back”buttontogobacktotheconfigurationscreen.

32

System configuration

Settings >> R2 Address settingsInthismenu,theaddressoftheR2canbeset.Thisaddressisfactorydefaultseton“001”andisselectablebetween“001”and“999”.WhenonlyoneR2isavailable,thedefaultaddresscanbelefttoitsdefaultvalue.

WhenmoreR2’sarecascadedthroughthefiberinterconnectionbus,thereneedstobeassignedauniqueaddressforeveryR2.ThefirstR2startswithaddress“001”,andeverysubsequentR2shouldbeassignedanaddresswithahighervalue.

Clickthe“OK”buttontoconfirmtheaddresssettings

Address Settings

33

Settings >> Fiber settingsInthiswindowcanbesetwhichaudiosignalsoftheR2shouldbetransmittedoverthefiberinterconnectioninterface.

NOTE

ThefiberinterconnectioninterfaceisanoptionalmodulefortheR2.(R2OPT)ThesettingswhicharemadeinthiswindowwillonlyaffectwhentheinternalfiberinterconnectioninterfaceoftheR2isinstalled.

ThesoftwareoftheR2amplifiersupportstotransferupto8stereochannelsoverthefiberinterconnectioninterface.

Inthe“FiberSettings”windowofthewebbaseduserinterfaceisanoverviewgivenofallthechannelswhichcanbetransmittedoverthefiberinterconnectioninterface,numberedfrom“FiberChannel1”to“FiberChannel8”.Nexttoeachchannelisadropdownlistdisplayedwherecanbeselectedwhichoftheaudiochannelsshouldbetransmittedoverthecorrespondingfiberbuschannel.

Inthisdropdownlistarealldirectlineinputs,allwallpanelinputs,allpriorityinputsandalladditionalDSPgeneratedsignalsdisplayed.

Whenanaudiochannelshouldbetransmittedoverafiberchannel,simplyclicktheaudiochannelinthedropdownlistofthedesiredfiberchannel.

Clickthe“Back”buttontogobacktotheconfigurationscreen.

FormoreinformationaboutcascadingtheR2andthefiberinterconnectioninterface, refertoChapter 8: Cascading the R2ofthisusermanual.

Fiber Settings

34

Settings >> Amplifier bridgingInthiswindowtheamplifieroutputsoftheR2canbebridged.

Justclickonthebuttoncorrespondingwiththezonewhichyouwanttobridge,andtheamplifiedLeftandRightoutputchannelsoftheoutputzonewillbebridged,becomingapowerof80Watt@8ohminsteadof2x40Watt@4Ohmor2x20Watt@8Ohm.(OnlywhentheR2POWpoweramplifierkitisinstalled).

Whenthebridgingfunctionisturnedon,the“LEFT”inputsignalwillusedforbothleftandrightoutputsignals.Theloudspeakershouldbeconnectedbetweenthe+terminaloftherightchannelandthe-terminaloftheleftchannel.

Clickthe“Back”buttontogobacktotheconfigurationscreen.

Amplifier Bridging

Settings >> Password settingsInthiswindowthepasswordsfortheR2canbechanged.Therearetwodifferentpasswordlevels.AdministratorlevelwhichhasfullaccesstoallfunctionsandUserlevel,whichhasonlyaccesstothebasicfunctions.

OntheleftsideofthewindowthesettingsfortheAdministratorpasswordcanbechanged,whileontherightsidethesettingsfortheUserpasswordcanbechanged.

Forchangingthepassword,entertheoldpasswordintheprovidedfield,andenterthenewpasswordtwiceintheprovidedfields.Afterthisalliscompleted,pushthe“OK”button.

Whentheoldpasswordiscorrect,andthenewpasswordfilledinbothfieldsmatch,theoldpasswordwillbechangedintothenewpassword.

Thefactorydefaultpasswordfor Administratorlevelis“R2”andforUseris“User”.

35

R2 Password Settings

Settings >> Factory settings

ATTENTION

BE CAREFULLtopressthisbutton.ItreallywillrecalltheORIGINALfactorysettings!!!

Itdoesnotrecallthepreviouslysavedsettings,butitrecallstheoriginalfactorysettingandthepreviouslymadesettingswillbelost.

Clickthe“OK”buttontoresetthesettingstofactorydefault.

Restore Factory Settings

36

Lite User Interface TheSmallwebbaseduserinterfaceoftheR2isespeciallydesignedtohaveaccesstoallbasicfunctionsoftheR2withanymobiledevicewithasmallscreen,suchasSmartphones,PDA’s,iPod/iPhone,..ToaccesstheLiteWebinterface,adevicewithawebbrowserandFlashplayer8ofhigherisrequired.

TheLiteWebBasedinterfacecanbeaccessedbytyping“/small.htm”aftertheIPaddressoftheR2.IftheIPaddressisthefactorydefaultIPaddress,youcanaccesstheLiteWebBasedUserinterfacebytypinghttp://192.168.0.191/small.htminyourwebbrowsersaddressbar.

Lite User Interface >> Login screenFirsttheloginscreenwillbedisplayed.EnterthepasswordtogetaccesstothelitewebinterfaceoftheR2amplifier.Afterthepasswordisentered,clickthe“OK”button,andiftheenteredpasswordiscorrect,youwillproceedtothemainscreenoftheR2.

Lite User Interface >> Main screenOntheMainscreenofthe“Lite”webbaseduserinterfaceisalwaysonlyoneoutputzonedisplayedatatime.Theconfigurednameofthecorrespondingoutputzoneisalwaysdisplayedontop.Thevolumecanbeadjustedbymovingthefaderupanddown,andthedesiredinputsignalcanbeselectedinthedropdownlistlocatedabovethefader.Theinputsignalsdisplayedinthisdropdownlistarethosewhichareconfiguredinthe“WallPanelSettings”menuforthatcorrespondingoutputzone.

Belowthefaderisabuttonprovidedwherebytheoutputsignalcanbemutedbysimplyoneclick.

Toproceedtothenextoutputchannel,simplyclickonthearrowsshownonthesideofthewindow.Withtherightarrowyoucangoonezonefurther,andwiththeleftarrowyoucangoonezoneback.

Small user interface for mobile devices

37

iPhone + iPadTheapplicationwhichisavailablefromtheappstoreturnsyouriPhoneoriPadintoafullyfledgedaudiomatrixcontrollerwhenusingitincombinationwithwiththeR2Matrix.SimplyconnectittoyourLANnetworkbyusingawirelessaccesspoint,andafterinstallingtheapponyourmobiledevice,itisreadytobeused.

Toinstalltheapponyourmobiledevice,justtapthe appstorebuttonanddownloadthe‘R2Remote’appbyAUDAConyourmobiledevice,ordownloadtheapplicationfromiTunes®.(Ifit’sdownloadedbyiTunes,youfirstneedtosynchroniseitbeforethe‘R2Remote’logowillappearonyourdisplay)

Aftertheappisinstalled,makesureyourmobiledeviceisconnectedtoyourwirelessnetworkandruntheappbytappingthe‘R2Remote’appbutton.Whenstarting-up,itwillaskfortheIPaddressofthedevicewhereitshouldbeconnectedtoandthepasswordshouldbeentered.Themobileapplicationsonlyoffersyouthepossibilitytochangebasicconfigurationsettingslikevolumeandroutingcontrol,sothe‘Administrator’and‘User’passwordbothofferyouthesamerightshere.

Afterthepasswordisentered,youwillberedirectedtothemainscreenoftheapp,showingonefaderforonespecificzone.Thevolumeforthisspecificzonecanbesetbymovingthefaderupanddownwardsandtheinputsignalcanbeselectedbytappingontheinputsignalsname.Thenalistwillbeshownwhereoutthedesiredinputsignalcanbeselected.Thegreenbuttononthebottomcanbeusedtomutethevolumeforthecorrespondingzone,andwillturnredwhenthevolumeismuted.Toswitchbetweenseveraloutputzones,justsweepoveryourdisplayfromlefttoright,orrighttoleft.

TheiPadappisworkingsimilarandveryintuitivejustastheiPodandiPhoneapp,theonlydifferenceisthatmultiplefaderswillbeshownbesidesoraboveeachother.Inhorizontalposition,all8faderswillbeshownnexttoeachother,whileinverticalpositiontworowsoffourfaderswillbeshownaboveeachother.

38

Chapter 6Peripheral interfacesTheR2offersthepossibilitytoconnectmanyadditionalinputandcontrolunitsinadditiontothestandarddirectlineinputs.Toconnectthoseadditionalunits,peripheralinterfaceportsareprovidedontherearsideoftheR2.Inthefurtherexplanationsofthisusermanual,wewillrefertotheperipheralinterfaceportswiththeletters“PI”,followedbyanumberrangingfrom1to10,eachrepresentingonePIportontherearsideoftheR2.Asthisalreadysuggests,thereare10PIportsavailableontherearsideoftheR2,eachofthemperformedwithanRJ45connector.8ofthesePIportsarecapableoftransportingbi-directionalaudioanddata(portsPI1-8),whiletheremainingtwoportsareonlycapableoftransportingdata(portsPI9-10).

Devices possible to connect to the PI ports: DW3018/4018 Basic wall panel with routing and volume control MutlipleDW3018/4018wallpanelscanbeconnectedinabusstructure.Thiswallpanelisonlyusingdigitaldatatransferandnoaudiotransfer,soitcanbeconnectedtoallperipheralinterfaceportsfromPI1toPI10.Theassignmentofthewallpanelwithazoneshouldbedoneintheuserinterface.

DW5065 Advanced wall panel with graphic display stereo line input and microphone input ThiswallpanelcancontrolmultiplezonesandhasadirectdigitalaudiolinktotheR2.OnlyoneDW5065wallpanelcanbeconnectedononePIport,andonlyPI1toPI8canbeusedforconnectingDW5065wallpanels.

APM Paging systemTheAPMpagingsystemcanbeusedtopagetodifferentpagingzonesoftheR2.PagingtozonesonotherR2’sisalsopossiblewhenmultipleR2’sarelinkedwitheach-otherthroughthe(optional)fiberinterface.APMpagingconsolescanonlybeconnectedtoPIportsPI1toPI8.MultipleAPMpagingconsolescanbeconnectedtoonePIport,usingabusstructurewithARJ03junctionboxes.WhenmultipleAPMpagingconsolesareconnectedtoonePIport,onlyoneAPMconsolecanannouncemessagesatatime,sothepagingisprioritybased.PagingwithdifferentAPMconsolesindifferentzonesispossiblewhentheAPM’sareconnectedtoseparatePIinputs.

Connection possibilities

Workingconnections:-MultipleDW3018/4018’sononePIinput(PI1toPI10)-OneDW5065andmultipleDW3018/4018’stoonePIinput(PI1toPI8)-OneAPMandmultipleDW3018/4018’stoonePIinput(PI1toPI8)-MultipleAPM’s(priority)andmultipleDW3018/4018’stoonePIinput(PI1toPI8)

Connectionsthatdon’twork:-DW5065andAPMtoonePIinput-DW5065toPI9orPI10-APMtoPI9orPI10-MultipleDW5065toonePIinput

Important

AlwaysmakesuretheR2ispoweredoffwhenconnectingordisconnectingdevicestothePIports.Whenanaudiosignalistransmittedtotheperipheralinputsfromanexternalinputdevice(e.g.DW5065wallpanelorAPMpagingconsole)theusedcablingshouldalwaysbeUTP/FTPCAT6cableorbetter.

39

Wall mounted control panelsTheR2installationcanbeexpandedwithadditionalwallcontrolpanels.Therearetwokindsofwallpanelsavailable,onestandardwallpanel(DW3018/4018)whichallowstoadjusttheroutingandvolumeforaparticularoutputzone,andoneAll-In-Onewallpanel(DW5065),whichprovidesthepossibilitytoconnectanadditionalLineofMicrophonesignalsourceinaspecificzone.

DW3018/4018 (Left) & DW5065 (Right) Wall panels

ThewallpanelsshouldbeconnectedwiththeperipheralportsontherearsideoftheR2,bymeansofTwistedpairUTP/FTPCAT5(orbetter)cablingforDW3018/4018andUTP/FTPCAT6(orbetter)cablingforDW5065.Itispossibletoconnectmultiplestandard(DW3018/4018)wallpanelsononesingleperipheralport(Upto32wallpanelsaccordingtoRS485specification).OnlyoneAll-In-Onewallpanelwithaudioinputs(DW5065)canbeconnectedtoeachperipheralport.

DW3018/4018 Basic wall panelFunctionsTheDW3018/4018isthebasicwallpanelwhichallowstocontroltheroutingandthevolumeoftheR2.Aselectionoutofupto8inputsignalscanbemadebymeansoftheDW3018/4018wallpanel.Theinputswhichareselectablebymeansofthewallpanelcanbeconfiguredintheuserinterfaceunder‘Zonesettings’and‘InputSelection’.Howthisworksisextensivelydescribedinanearlierchapterofthisusermanual.FirstreadthePIconnectionprinciplesinthebeginningofthischapterbeforemakinganyconnections.

Change routingInnormalconditions,theDW3018displaywillshowtheroutingbyindicatingthenumberoftheselectedinputsignalwhichisroutedtotherelatedzone.Ifthe“Prog+”buttonispressed,thenextpre-definedinputwillbeselected,ifthe“Prog-”buttonispressed,thepreviouspre-definedinputwillbeselected.Change volume Thevolumeinthecorrespondingoutputzonecanbechangedbypressingthe“Vol+”and“Vol-”buttons.Logically,thevolumewillbeincreasedafterpressingthe“Vol+”buttonwillbedecreasedafterpressingthe“Vol-”button.Whenthevolumeischanged,thedisplaywillshowthevolumelevelfortwoseconds,andafterthosetwoseconds,theroutingwillbedisplayedagain.

ConfigurationBeforetheDW3018/4018wallpanelscanbeused,thewallpanelsneedstobeassignedtooneparticularzone.Performtheproceduredescribedbelowtomakesurethisisdonecorrectly.

Gotothe“Setup”menuandclick“Systemconfiguration”.Nowyouhavethepossibilitytochoosebetween“Paging”,“DW5065”and“DW3018/4018”.ToconfigurethesettingsfortheDW3018/4018wallpanels,clickthecorrespondingbutton.Nowawindowwithadropdownlistisshown,displayingalltheavailablezonenames.Selectthezonewheretoawallpanelshouldbeassigned,andclickthe‘SetAddress’button.Allconnectedwallpanelswillstartblinking,andafterpressingtheupperbuttononthedesiredwallpanel,itwillbelinkedtotheselectedoutputzone.Ifmultiplewallpanelsshouldbeassignedtoonezone,simplyrepeatthisaction.

Prog.

Vol+

-

+

-

AUDAC

LINE IN

MIC IN

40

Maximum cable lengthThemaximumcablelengthdependsofthenumberofconnectedwallpanel.Whenonlyonewallpanelisconnected,amaximumcablelengthof600meterscanbereached.Thetablebelowgivesanoverviewofthemaximumcablelength,dependingoftheconnectedwallpanels.

No. of DW3018/4018 Wall panels Maximum cable length

12345678

600meter600meter400meter300meter200meter150meter120meter100meter

DW5065 All-in-one wall panelFunctions TheDW5065istheadvancedAll-in-onewallpanelfortheR2.Thiswallpanelhasagrahicdisplayandcancontroltherouting,volume,bass,trebleandmuteformultiplezones(upto8)ononeR2.Besidesthosecontrolfunctions,italsoprovidesthepossibilitytoconnectamicrophoneandastereolineinputsource.TheDW5065wallpanelshouldbeconnectedtotheR2bymeansofaUTP/FTPCat6(orbetter)cable.FirstreadthePIconnectionprinciplesinthebeginningofthischapterbeforemakinganyconnections.

ThefollowingfunctionsofmultiplezonesoftheR2canbecontrolled: -Volumewithinarangeof0dBto-70dB -Allinputscanbeselected -Mutecanbeactivated -Basswithinarangefrom-9dBto+9dB -Treblewithinarangefrom-9dBto+9dB

ConfigurationBeforetheDW5065canoperate,theconfigurationsshouldbemade.Firstofall,anaddressneedtobeassignedandtheavailableinputsneedtobedefined.

Followthesestepstoconfigure:1)Gotothe“Setup”menuandclick“Systemconfiguration”.Nowyouhavethepossibilitytochoosebetween“Paging”,“DW5065”and“DW3018/4018”.ToconfigurethesettingsfortheDW5065wallpanels,clickthecorrespondingbutton.NowawindowisdisplayedwhichprovidesalltheconfigurationpossibilitiesfortheDW5065.Ontheleftside,adropdownlistisdisplayedwherebytheaddressfortheDW5065canbeselected.Theaddresscanbeselectedbetween“W001”and“W008”.Logically,youstartwithaddress“W001”forthefirstwallpanel,andincreasesforeveryadditionalwallpanel.Afterthedesiredaddressisselected,clickthe“Setaddress”button.Afterthisbuttonispressed,theDW5065willstartblinking.Toconfirmtheselectedaddresswiththewallpanel,clickthebigrotarybuttononthefrontofthewallpanel.Whenthisbuttonispressed,theaddresswillbeassignedtotheselectedwallpanel.

2)Thezoneswhichyouwanttocontrolwiththeselectedwallpanelcanbeselectedbymeansofthe“Controlledzones”dropdownlist.Whenselectingazoneinthisdropdownlist,thezonenamewillappearinthelistboxbelow.Thezonescanberemovedagainfromthislistboxbyselectingthem,andclickingthe“RemoveZone”button.

3)Theinputswhichareselectablewiththeselectedwallpanelcanbeselectedbymeansofthe“Selectableinputs”dropdownlist.AllinputswhichavailableontheR2canbeselectedinthisdropdownlist,suchasthedirectlineinputs,theperipheralinputs,thefiberinputs,thepriorityinputsandtheintegratedDSPsignals.Whenselectinganinputsignalinthislist,thesignalnamewillappearinlistboxbelow.Theinputsignalscanberemovedagainfromthislistboxbyselectingthem,andclickingthe“RemoveInput”button.Amaximumof24signalinputscanbeselected.Theinputswhichareselectedinthislistbox,areavailableforallzoneswhichcanbecontrolledbythisDW5065wallpanel.ThoseinputsarenotlinkedwiththequickmenuliketheinputsontheDW3018/4018are.

41

4)CertainactionssuchasVolumechange,Inputchange,Mutechange,Tonecontrolchangeandsettingschangecanbeblockedbycheckingthecheckboxes.

5)Themicrophoneinputhasthepossibilitytoprovide+15Vphantompowerforpoweringcondensermicrophones.ThepantompowercanbeswitchedONandOFFbyclickingthe“EnableMicPhantom”checkbox.ThissettingcanalsobechangedintheDW5065settingsmenu.(If“Blocksettingsmenu”isnotchecked)

6)TheBacklightlevel,screensaverandscreensaverdelaycanbesetbymeansofthreedropdownboxes.ThissettingcanalsobechangedintheDW5065settingsmenu.(If“Blocksettingsmenu”isnotchecked)

7)Whenthesettingsaremade,pressthe“SavetoWallpanel”buttonandthesettingswillbesendtotheselectedDW5065wallpanel.

Previouslymadesettingscanberetrievedfromthewallpanelbyclickingthe“LoadfromWallpanel”button.Hereby,thesettingswhicharestoredinthewallpanelwillbedisplayedinthiswindow,makingitpossibletomakeanychangestothecurrentsettings.

Maximum cable length for DW5065 ThemaximumcablelengthfortheDW5065wallpanelis300meter.

Connection possibilities

Prog.

Vol+

-

+

-

AUDAC

LINE IN

MIC IN

Prog.

Vol+

-

+

-Prog.

Vol+

-

+

-

Multiple DW3018/4018 Wall panels on one PI Port (PI1 to PI10)

Prog.

Vol+

-

+

-Prog.

Vol+

-

+

-

Multiple DW3018/4018 and one DW5065 Wall panel on one PI Port (PI1 to PI8)

42

43

Chapter 7Paging1 Zone paging example ThemostbasicexampleofanR2pagingsystemisanR2audiomatrix,incombinationwithanAPM101pagingconsole.Thissetupmakesitpossibletoannouncemessagesin1ormorepre-definedzones,andwithapre-definedvolumeforeveryzone.

8 Zone paging exampleAsecondpagingexampleofanR2pagingsystemisanR2audiomatrix,incombinationwithanAPM108pagingconsole.Thedifferencebetweenthepreviousexample(withAPM101)aretheamountofpagingzones.TheAPM108consolecontains8zoneselectionbuttons,whichmakesitpossibletopageseparatelytoallzones,ortopagetomultiplezonesatatime.

Priority Pagingisalwaysprioritybased.WhenmultipleAPMconsolesareconnectedtooneR2,andmultipleAPM’sgiveacommandtoannounceamessageatthesametime,itdependsoftheprioritysettingswhichmessagewillbeannounced.TheprioritylevelisrelatedtotheaddressoftheAPMtable,whichisunique.TheAPMwiththelowestaddresshasthehighestpriority.Thismeans,whentwoAPM’sareconnectedandAPMwithaddress“002”isannouncingamessage,whileatthesametimeAPMwithaddress“001”wantstoannounceamessage,themessagefromAPM“002”willbeinterrupted,andthemessagefromAPM“001”willbeaudible.ForvoicefilesandmessageswhicharestoredinsidetheAPMmemory,thepriorityworksdifferent.Aprioritynumbercanbeassignedtoeachstoredmessage,makingitpossibletogiveemergencymessagesahigherpriority.

Connection possibilities TwodifferentconnectionmethodsarepossibleforconnectingmultipleAPM’stooneR2.

1)BusstructureMultipleAPM’scanbeconnectedinabusstructure,onthesamePIInput.OnlyoneAPMpagingconsole

R2

R2

44

2)SeparatePIinputMultipleAPM’scanbeconnectedtotheR2,eachofthemusingaseparatePIInput.Iftheselectedpagingzonesaredifferent,pagingtodifferentzonescanbedoneatthesametime.IfmultipleAPM’saretryingtopagetothesamezoneatthesametime,thenpagingisprioritybased,andonlythemessagecomingfromtheAPMwiththehighestpriority(lowestaddress)willbeannounced.

Paging over fiber WhenmultipleR2’sarecascadedwitheachotherthroughthefiberinterconnectioninterface,pagingmessagescanbetransferredoverthefiberconductor,makingpagingpossibleinmultiplezonesofmultipleR2’s.Whenthisoptionisenabled,audiochannelone(FB1)isdedicatedforpagingpurposes,wherebythischannelcan’tbeusedforotherpurposes.Pagingoverfiberisalwaysprioritybased,andonlyoneAPMcanpagetomultipleR2’satthesametime.

Limits WhenmultipleAPM’sareconnectedononePIportusingabusstructure,amaximumof6APM’scanbeconnectedtoonePIport,withamaximumcabledistanceof300meterforthetotalAPMbus.

Connection limits summary

-Maximum6APM’sononePIport-Maximum100mwhenCat5cableisused-Maximum300mwhenCat6cableisused-AlwaysuseARJ03PjunctionboxeswithexternalpowersupplywhenmultipleAPM’sareconnectedusingBusstructure.-UseARJ03PwithexternalpowersupplywhenthecablelengthforoneAPMexceeds133meter.

Bus

Max300meter

45

ConfigurationTomaketheentirepagingsystemworkacordingtotheneedsofyourproject,aconfigurationprocedureshouldmustbefollowed.

Paging volume Thepagingvolumecanbedifferentforeveryzone,andshouldbeconfiguredindividualforeachspecificzone.Toconfigurethepagingvolume,gotothe“Setup”menu,andclickthe“Pagingvolume”button.Bymeansofdropdownboxes,thepagingvolumeforeveryspecificzonecanbeset.

APM configuration ThepagingsettingsarestoredinsidetheAPM’sinternalmemory.Forconfiiguration,theAPMshouldbeconnectedtotheR2,andtheconfigurationshouldbedonethroughthewebbaseduserinterfaceoftheR2.Youcanfindthepagingconfigurationsettingsinthe“Setup”menu,under“Systemconfiguration”,and“Paging”.OntheleftsideofthewindowarethesettingsforconfigurationofARU’sshown,whileontherightsidethesettingsforconfigurationoftheAPM’sareshown.Followtheprocedurebelowtomakeyourpagingsystemworksuccessfull.

1)Selecttheaddresswhichyouwanttoassigntoyourpagingconsole.Selecttheaddressbythedropdownbox,andclickthe“SetAddress”button.Now,thelightsonallconnectedAPM’swillstartblinking.Afterpushingthe“PTT”(Pushtotalk)buttontheaddresswillbeassignedtotheselectedAPM.FormoreinformationregardingtheAPMaddress,see“Priority”.WhenmultipleAPM’sareconnectedtooneR2,it’sbettertoassignanuniqueaddresstoeveryAPM,beforecontinuingwiththeconfigurationprodure.

2)SelecttheAPMandtheamountoflayersforyourconfiguration.Press“NewConfiguration”.Afterpressingthisbutton,youwillberedirectedtoanewwindowwhereyoucanselectwhichAPMyouwanttoconfigure.Twodropdownboxesareshown,bymeansoftheupperonetheR2wheretotheAPMisconnectedshouldbeselected.WhenonlyoneR2isused,only“R001”willbeshown.Bythelowerdropdownlist,theperipheralportonwhichtheAPMisconnectedcanbeselected,rangingfromRS485(1)toRS485(8).WhenAPM108orAPM116areconnected,thenumberoflayersforyourAPMconfigurationcanbedeterminedbymeansofthedropdownlistontherightsideofthiswindow.

WhenthedesiredAPM(andtheamountoflayers)isselected,clickthesavebutton,andyoucanproceedtothenextwindow.

46

3)ConfiguretheAPMbuttonsThiswindowgivesanoverviewofyourAPMkeypad.ThenumberofbuttonsdisplayedinthiswindowdependsofthetypeofAPMwhichisconnectedtoyoursystem.Ontheleftside,adropdownlistallowsyoutobrowsebetweenthelayers(whenavailable).Justclickthebuttontowhichyouwanttoassignafunction.

Afterthisbuttonisclicked,awindowscomesupallowingyoutoselectthefunctionwhichshouldbeperformedafterpressingthisbutton.Theavailablefunctionsshowninthedropdownlistontheleftsideare“ZoneSelect”and“PlayMessage”.

Zone Select:Thisfunctionshouldbeselectedwhenthebuttonismeantforpagingpurposes.Thezoneswherethemessageshouldbeaudibleafterpressingthebuttonaredisplayedinthe“SelectedZones”listbox.Zonescanbeaddedtothislistboxbyselectingtheminthetwodropdownlistsontherightsidefollowedbyclickingthe“Add”’button.Zonescanberemovedfromthislistboxbyselectingthem,andclickingthe“Remove”button.Upto40zones,from5cascadedR2’scanbeprogrammedunderonebutton.ThepriorityofpagingisbasedontheAPMaddressconfiguration.

47

Play message:Bymeansofthisfunction,messagesstoredintheAPMmemory,suchasemergencyorcommercialannouncementscanbeannounced.Thestoredmessagesareshowninthe“Message”dropdownlistwhereoutthedesiredmessagecanbeselected.Thepriorityofthemessageisbasedontheprioritynumberwhichcanbesetinthe“Priority”dropdownlist,andisnotrelatedwiththeAPMaddress.Thisway,high-priorityemergencymessagescanbeplayedwithalow-priorityAPM.Thelowertheprioritynumberis,thehigherthepriorityoftherelatedmessage.

48

49

Chapter 8Cascading the R2ThischapterexplainsthefiberinterconnectionpossibilitiesbetweenseveralR2amplifiers,andguidesyouthroughasetupprocessofaprojectwith5R2’scascadedwitheachotherbymeansofthefiberinterconnectioninterface.

Principle The(optional)fiberinterconnectioninterfacemakesitpossibletotransfer8stereoaudiosignalsandonedatachanneloveronesinglefiberopticconductor.Thedatachannelistransmittedautomaticallyandcan’tbeconfiguredbytheuser.The8stereoaudiochannelswhichshouldbetransferedoverthefiberconductorcanbeconfiguredbytheuser.

ThefiberinterconnectioninterfaceoftheR2workslikearingnetwork.ThismeansthateveryR2hasonefiberinputandonefiberoutput.ThisringmustbeclosedinallcasesandthiscanbedonebyconnectingtheoutputofthefirstR2withtheinputofthesecondR2.TheoutputofthesecondR2shouldbeconnectedwiththeinputofthethirdR2,andsoon.Attheend,theoutputofthelastR2hastobeconnectedwiththeinputofthefirstR2.Thisway,aringisclosedandthenetworkiscompleted.

TocontrolallthefunctionsofalltheR2’sinonenetwork,onlyoneconnectionwiththeethernetnetworkofoneR2intheringnetworkisrequired.WhenmultipleR2’sareconnectedinaringnetwork,firstaselectionboxwillbedisplayedwherebycanbeselectedwhichR2youwanttocontrol.

EachR2cantransferoneormultipleofhisinputchannelsthroughthefiberringnetwork.ThiscanbeanyinputoftheR2(Lineinput,PIaudioinput,Digitalinput,...).Theselectionofwhichinputsignalshouldbetransferedoverthefiberringnetworkcanbeselectedinthe“Setup”menu,afterselectingthe“Fibersettings”window.

Everysignalwhichisreceivedthroughthefiberringnetworkcanbeusedasaregularinputjustasalltheotherinputs,canbeselectedthroughthewallpanels,andcanbepatchedtoanyoftheoutputzones.

WhenanR2transfersanaudiosignaloverthefiberringnetwork,thereisthepossibilitytotransferthesignaltoallR2’sinthesameringnetwork,ortotransferthesignalonlytothenextR2intheringnetwork.IfthesignalisonlyneededforthenextR2intheringnetwork,thesecondR2canusethischanneltotransferanothersignaltothethirdR2,andsoon...

R2R2R2

50

Fiber audio flowThediagramshownbelowshowsanaudioflowofanexampleprojectwith5R2’scascadedthroughthefiberinterconnectioninterfacewhereeveryR2hasanaddressgoingfrom“R001”to“R005”.NexttoeveryR2areshownwhichsignalsarereceivedandtransmittedoverthefiber,whilenexttotheconnectionlineisshownwhichsignalsthefiberiscarryingatthispoint.

Pagi

ng

R005

(1)

R005

(2)

R001

(1)

R003

(1)

R004

(1)

R005

(4)

R005

(3)

In

Fb 1 Fb 2 Fb 3 Fb 4 Fb 5 Fb 6 Fb 7 Fb 8 Channel

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R004

(1)

R001

(2)

R005

(3)

Out

R2

R2

R2

R2

R2

R001

R002

R003

R004

R005

Pagi

ng

R005

(1)

R005

(2)

R001

(1)

R003

(1)

R004

(1)

R001

(2)

R005

(3)

In

Fb 1 Fb 2 Fb 3 Fb 4 Fb 5 Fb 6 Fb 7 Fb 8 Channel

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R002

(1)

R002

(2)

R005

(3)

Out

Pagi

ng

R005

(1)

R005

(2)

R001

(1)

R003

(1)

R002

(1)

R002

(2)

R005

(3)

In

Fb 1 Fb 2 Fb 3 Fb 4 Fb 5 Fb 6 Fb 7 Fb 8 Channel

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R002

(1)

R003

(2)

R005

(3)

Out

Pagi

ng

R005

(1)

R005

(2)

R001

(1)

R003

(1)

R002

(1)

R003

(2)

R005

(3)

In

Fb 1 Fb 2 Fb 3 Fb 4 Fb 5 Fb 6 Fb 7 Fb 8 Channel

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R004

(1)

R004

(2)

R005

(3)

Out

Pagi

ng

R005

(1)

R005

(2)

R001

(1)

R003

(1)

R004

(1)

R004

(2)

R005

(3)

In

Fb 1 Fb 2 Fb 3 Fb 4 Fb 5 Fb 6 Fb 7 Fb 8 Channel

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R004

(1)

R005

(4)

R005

(3)

Out

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R004

(1)

R001

(2)

R005

(3)

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R002

(1)

R002

(2)

R005

(3)

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R002

(1)

R003

(2)

R005

(3)

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R004

(1)

R004

(2)

R005

(3)

Pagi

ng

R005

(1)

R005

(1)

R001

(1)

R003

(1)

R004

(1)

R005

(4)

R005

(3)

Diagram

Fiber audio flow

51

Diagram explanationEveryR2isindicatedwithadifferentcolour,andnexttoeveryR2isatableshownwith8incomingfiberaudiochannelsand8outgoingfiberaudiochannels.Betweentwodevices,aconnectionlineisshownrepresentingthefiberconductor,andnexttothisconnectionlineisalwaysatableshownwhichindicatestheaudiochannelsthefiberconductoriscarryingatthispoint.Theaudiochannelsbetweentheoutputfromthepreviousdeviceandtheinputofthenextdevicearealwaysunchanged.Thisisclearlydisplayedbymeansofthetextcolourinsidethetables.WhenAPMpagingconsolesareconnectedandpagingoverfiberenabled,thenchannel“Fb1”isdedicatedforpaginguseandcan’tbeusedtoexchangeotheraudiochannels.Forthisreason,channel“Fb1”isalwaysmarkedwith“Paging”.

Anoverviewoftheaudiosignalstransmittedoverthefiberinterface:

- Fiber channel 1 (Fb 1): Thischannelisdedicatedforpagingpurposes

- Fiber channel 2 (Fb 2): TheRedR2(R005)transmitsanaudiosignaloverfiberchannel“Fb2”. Thissignalreachesalldevicesandcanbeusedbyalldevices.

- Fiber channel 3 (Fb 3): Sameaschannel“Fb2”,theRedR2(R005)transmitsanaudiosignalover fiberchannel“Fb3”.Thissignalreachesalldevicesandcanbeusedbyall devices.

- Fiber channel 4 (Fb 4): TheYellowR2(R001)transmitsanaudiosignaloverfiberchannel“Fb4”. Thissignalreachesalldevicesandcanbeusedbyalldevices.

- Fiber channel 5 (Fb 5): TheBlueR2(R003)transmitsanaudiosignaloverfiberchannel“Fb5”. Thissignalreachesalldevicesandcanbeusedbyalldevices.

- Fiber channel 6 (Fb 6): Channel6isusedbytwoR2’s.TheOrangeR2(R004)transmitsanaudio signaloverfiberchannel6“Fb6”,andthissignalreachestheRedR2(R005), theYellowR2(R001)andtheGreenR2(R002).TheGreenR2(R002) replacesthesignalonfiberchannel“Fb6”byanotheraudiosignal,andthis audiosignalreachestheBlueR2(R003)andtheOrangeR2(R004).

-Fiber channel 7 (Fb 7): Fiberchannel7(Fb7)isusedbyallR2’s.EveryR2receivesandtransmitsan audiosignaloverthischannel.Thisway,everyR2canuseasourceofthe previousR2andreplaceitbyanothersignalwhichcanbereceivedbythe nextR2intheringnetwork.

- Fiber channel 8 (Fb 8): Sameaschannels“Fb2”and“Fb3”,theRedR2(R005)transmitsanaudio signaloverfiberchannel“Fb8”.Thissignalreachesalldevicesandcanbe usedbyalldevices.

52

Setting up the projectThischapterdescribesastepbystepsetupprocedurewhichteachesyouhowtoconfigureanR2setupwithmultipledevicesasshownonthepreviouspages.

NOTE

Don’tmakeanyethernetorfiberconnectionsuntilthispoint.Thesetupshouldbeconfiguredinthesamesequenceasdescribedinthisstepbystepguide.

1) Configuration of R2 Address Thefirstthingwhichshouldbedone,isconfiguringtheIPandbusaddressesofalldevicesusedinyoursetup.Whendevicesarecascadedthroughfiber,thecontrolcanbedoneintwodifferentways:

Method 1: ConnectonedevicetoEthernet,andcontroltheotherdevicesinyoursetupthroughthesameIPaddress.Thedatawillbetransferredbetweenthedevicesoverthefiberconductor.Theadvantageofthismethodis:OnlyoneEthernetconnectionisnecessary.Thedisadvantageofthismethodis:youcanonlyseetheVUmetersintheuserinterfaceoftheR2whichisdirecltlyconnectedtotheEthernetnetwork.(Allothersettingscanmemade,excepttheVUmeterbargraphwhichisonlyvisibleforthedirectconnectedR2)

ToconfigureyoursystemaccordingtoMethod1,proceedwiththefollowingprocedure:

1) ConnectthefirstR2ofyoursetuptoyourEthernetnetwork2) SettheaddressforthefirstR2to“R001”,thiscanbedoneinthe“Setup”menu,under“R2 AddressSettings”.3) DisconnectthefirstR2ofyoursetupfromtheEthernetnetwork4) ConnectthesecondR2ofyoursetuptoyourEthernetnetwork5) SettheaddressforthesecondR2to“R002”,thiscanbedoneinthe“Setup”menu,under“R2 AddressSettings”.6) DisconnectthesecondR2ofyoursetupfromtheEthernetnetwork7) RepeatthisprocedureforallR2’sinyoursetup,andassignanuniquebusaddresstoeveryR2in yoursetup.8) Afterthisisdone,allR2’sshouldhaveanuniquebusaddress,andnoR2islongerconnectedto theEthernetnetwork.9) ConnectoneoftheR2’sinyoursetuptotheEthernetnetwork.(Itdoesn’tmatterwhichone youconnecttotheEthernetnetwork,butmindyoucanonlyseetheVUmeterbargraphmoving oftheconnectedR2)10) ConnecttheR2’switheachotherthroughfiberconductors,usingtheloopprincipleasshownin Figure1.11) RestartallR2’s12) AllR2’sshoulddisplaynow“FiberOK”ontopoftheirmainpage,nexttotheconnectionstatus.

Method 2: ConnectalldevicestoEthernet,andcontrolthembytheirownIPaddress.Theadvantageofthismethodis:youcanseetheVUmetersofallconnectedR2’s.Thedisadvantageofthismethodis:everydeviceneedshisownEthernetconnectionandIPaddress.

ToconfigureyoursystemaccordingtoMethod2,proceedwiththefollowingprocedure:

1) ConnectthefirstR2ofyoursetuptoyourEthernetnetwork2) SettheaddressforthefirstR2to“R001”,thiscanbedoneinthe“Setup”menu,under“R2 AddressSettings”.3) ChangetheIPaddressforthefirstdevicetoonewhichisavailableinyourethernet network(Forexample192.168.0.191).Thiscanbedoneinthe“Setup”menu,under“Network Settings”.4) DisconnectthefirstR2ofyoursetupfromtheEthernetnetwork5) ConnectthesecondR2ofyoursetuptoyourEthernetnetwork6) SettheaddressforthesecondR2to“R002”,thiscanbedoneinthe“Setup”menu,under“R2 AddressSettings”.

53

7) ChangetheIPaddressfortheseconddevicetoonewhichisavailableinyourethernet network(Forexample192.168.0.192).Thiscanbedoneinthe“Setup”menu,under“Network Settings”.MakesurethisIPaddressisdifferentfromthefirstdevice’sIPaddress.8) DisconnectthesecondR2ofyoursetupfromtheEthernetnetwork9) GivealltheR2’sinyoursetupanuniquebusandIPaddress.Thiscanbedonebyrepeatingstep 5to8ofthisprocedure.MakesureeverydevicehasanuniquebusandIPaddress.10) Now,alldeviceshaveanuniquebusandIPaddress,andnodeviceisconnectedtotheEthernet network.11) Connectalldevicestoyourethernetnetwork12) ConnecttheR2’switheachotherthroughfiberconductors,usingtheloopprincipleasshownin Figure1.13) RestartallR2’s14) AllR2’sshoulddisplaynow“FiberOK”ontopoftheirmainpage,nexttotheconnectionstatus.

Example setup with 5 R2’s, on the left side with only one Ethernet connection (Method 1) while on the right side every R2 has a separate ethernet connection (Method 2)

R2

R2

R2

R2

R2

R001

R002

R003

R004

R005

R2

R2

R2

R2

R2

R001

R002

R003

R004

R005

ethernet

192.168.0.191

ethernet

192.168.0.191

ethernet

192.168.0.192

ethernet

192.168.0.193

ethernet

192.168.0.194

ethernet

192.168.0.194

54

2) Configuration of Fiber channels Thenextstepistheconfigurationoftheaudiochannelstransmittedoverthefiberconductor.Thiscanbedoneinthe“Setup”menu,under“Fiberettings”.Below,we’llgiveastepbystepguideaboutthefiberconfigurationforonedeviceinyoursetup.Let’sstartwiththefirstR2withaddress“R001”(indicatedinYellow)inyoursetup.

1) OpentheuserinterfaceoftheselectedR2“R001”.2) Openthe“Settings”menuandclickthe“FiberSettings”button.3) Asshowninfigure1,“R001”transmitsaudiosignalsoverfiberchannel“Fb4”and“Fb7”.For alltheotherfiberchannels,“R001”justsendtheincomingdatatothenextR2.Soasource signalshouldbeselectedforfiberchannels“Fb4”and“Fb7”.AllsignalsavailableontheR2 canbeselectedbymeansofthedropdownlist.Forallotherchannelswheretheincomingdatais justsendtothenextR2,status“off”shouldbeselectedinthedropdownlist.

4) RepeatthisprocedureforallR2’sinyoursetup5) Afterthisisdone,allselectedaudiosignalsaretransmittedoverthefiberconductor,andcanbe usedbyotherR2’sinyoursetup.

3) Set passwords Youcanskipthisstepifthedefaultpassword“R2”foradministratorand“user”forusersisOKforyou,butwealwaysrecommendtochangethepasswords.Adetailleddescriptionhowthepasswordscanbechangedcanbefoundinsideanearlierchapterofthisusermanual.It’sconvenienttogivealltheR2’sinyoursetupthesameadministratorpassword,makingitpossibletoswapbetweenR2’swithoutconstantlyreenteringthepassword.Atuserlevel,it’salwaysnecessarytoreenterthepasswordafterswappingbetweenR2’s.

4) Connecting sources Connectallyouraudiosources(CD-players,Tuners,...)tothelineinputsonthebackoftheR2.Adjustallinputgainssothereisnoclipping.Moreinformationaboutconnectingsourceisextensivelydescribedinanealierchapterofthisusermanual.

5) Connecting wallpanels ConnectallyourwallpanelstothePeripheralinputsontherearoftheR2.Adetaileddescriptionaboutconnectingwallpanelsisextensivelydescribedinanearlierchapterofthisusermanual.

6) Ready Yourprojectisnowreadyforuse.

55

Chapter 9Additional information

IP BasicsManyAUDACproductsarecontrollablebyEthernet.TheEthernetconnectionwhichisusedontheAUDACproductsisTCP/IPbasedlike99%ofthecomputernetworks.TherearesomebasicswhichyouneedtoknowtosuccessfullymakeaTCP/IPEthernetconnection.

ThedatainTCP/IPnetworksisalwayssendinpackages,allthesepackagesmustbedeliveredatanuniqueaddress,justlikethemailmandeliversmailatyourhomemailbox.InTCP/IPnetworks,thisaddressiscalledthe“IPaddress”.TheIPaddressisalwaysanumberinthefollowingformat“192.168.000.001”.Asyoucansee,thisaddressconsistsof4separatenumbersrangingfrom“000”to“255”.

Insimpleterms,onlythelatestnumberofanIPaddresscanbedifferentwithinanetwork,sothereisamaximumof256uniqueaddresseswithinanetwork,rangingfrom“xxx.xxx.xxx.000”to“xxx.xxx.xxx.255”.Thefirstthreenumbersmustbethesametomakecommunicationbetweenseveraldevicespossible,elsethedevicescannotcommunicatewitheachother.Example: Device1: IPaddress: 192.168.000.001Device2: IPaddress: 192.168.000.002Device3: IPaddress: 192.168.001.003

Inthisexample,Device1cancommunicatewithDevice2,butnotwithDevice3,becausethefirstthreenumbersmustbethesame.Thesefirstthreepartsarecalledthe“IPrange”,sothedevicesmustbeinthesame“IPrange”tocommunicatewitheachother.

The“IPrange”ofhomeandofficenetworksaredefinedbythenetworkadministrator,thismeansthattheIPrangeofyourhomeorofficenetworkcanbedifferentfromanothernetwork.AUDACproductshavethefollowingIPaddressasdefault:“192.168.0.xxx”,thismeansthestandardIPrangeofAUDACproductsis“192.168.000.xxx”.IfyournetworkisusingadifferentIPrange,theAUDACproductswillnotbeaccessiblefromyournetwork.YoucanchangetheIPaddressoftheAUDACproductstomakethemworkproperlyinyournetwork.Thiscanbedoneinthesettingsmenu,andisdescribedextensivelyinthe“Settings”chapterofthisusermanual.

Ofcourse,tomakechangestothesettingsmenuoftheAUDACproducts,youmusthaveaccesstotheuserinterfaceontheproductswebpage.ThiscanbedonebytemporarilygivingyourcomputeranIPaddresswithintheIPrangeoftheAUDACproduct,forexample“192.168.0.200”.AftertheIPaddressofyourcomputeriswithintheIPrangeoftheproduct,theuserinterfaceisaccessibleandtheIPaddressoftheproductcanbechangedtoanIPaddresswithintheIPrangeofyournetwork.IftheIPaddressoftheproductiswithintheIPrangeofyournetwork,youcanchangetheIPaddressofyourcomputeragaintoit’sformerIPaddressandtheproductshouldworkproperlyinyourhomeorofficenetwork.Askyournetworkadministratorforhelpifyouarenotfamiliarwithnetworks.

Summary

-AlldevicesmusthaveanuniqueIPaddress-AlldevicesmustbewithinthesameIPrange

56

Updating the R2OverviewTheR2updateconsistsofthreesteps:1) DSPupdate2) FPGAupdate3) Websiteupdate

Required software Alltherequiredsoftwaretoaccomplishasoftwareupdateisavailableintheziparchivewhichcanbedownloadedfromthewebsite.

Step 1: DSP update 1)TurntheR2poweron2)ConnectacomputerwiththelowerUSBport(USBB)onthefrontoftheR2amplifier

3)Ifthedriverisrequested,theninstallthesupplieddriverfromtheziparchive4)Run“DSP2.exe”frommap“DSP&FPGA”5)Press“F6”6)Enter“R2S33H1.ldr”asfilename7)Waitforfinish,don’tclosetheapplication

Step 2: FPGA update 8)Press“F9”9)Enter“R2F11H1.rpd”asfilename10)Waitforfinish11)Press“Esc”toclosetheapplication12)DisconnecttheUSBcable13)R2poweroff->poweron

Step 3: Website update 14)ConnecttheR2networkcable15)Run“MPFS2.exe”frommap“Website”16)Inpoint1selectmap“1.7”inmap“Website”17)Inpoint2selecy“BIN”18)Press“settings”inpoint4andentertheR2IPaddressinthebox“DeviceAddress”.Ifyoudo’tknowtheIPaddressuse“MicrochipEthernetDiscover”inthemap“Website”tofindtheIPaddressoftheR2.19)Press“GenerateandUpload”tostartuploadingthenewwebsite20)Clearyourinternetbrowsercache.Ifyoudon’tdothis,yourbrowserwillloadtheoldwebsitefromhiscache.21)Finished

R2

57

Technical specificationsSensitivityLineinput -20/+4dB25kOhm

Frequencyresponse 20Hz–20kHzTHD+Nat1kHz lessthan0.02%SignaltoNoiseratio 100dB@1kHzSlewrate +/-13V/µsec

Digitalcontrol RS-232Remotezonecontrol RS-485Webbasedcontrol Ethernet

Zoneoutputs1-8 +3dB100Ohmunbalanced

PowerSupply 240VAC,50-60Hz

Weight 10kg

Dimensions(WxHxD) 482x132x350mm

Unitheight 3HE

58

Notes

59

Notes

60

Notes

Recommended