2018 Rental GUIDE - rmsequipment.com · With NPK GH15 Hammer — $8,150* $24,415* Additional Charge for Q.Coupler — $365 $1,090 *Plus point wear per inch as shown

MINNESOTA EDITIONVOL. 2018 NO. 2

2018 Rental

GUIDE

Model Day Week Four Week HP Operating Weight (lbs)D37PX-24** $575 $1,720 $5,150 89 20,503D39PX-23* $590 $1,770 $5,310 105 21,363D39PX-24** $630 $1,860 $5,580 105 22,817D51PX-24** $715 $2,150 $6,590 131 31,262D61PX-24** — $3,390 $10,140 168 42,902D65PX-17* — $4,640 $13,940 205 47,335 D65WX-17* — $4,470 $13,250 205 45,945D155AX-8** — $7,000 $21,000 354 89,300With Ripper — $7,590 $22,758 354 97,590

Model Day Week Four Week HP/Heaped Empty Max GVW Capacity Weight (lbs)HM300-5** — $4,675 $14,000 332/22.4CY 55,986 117,892 HM400-3* — $6,100 $18,280 469/40T-29.2CY 74,207 162,569HM400-5** — $6,415 $19,240 469/31.4CY 77,488 165,633 HM400 Water Truck $5,420 $16,250 8,000 Gal. Water Tank 74,207 162,569

Model Day Week Four Week HP/Heaped Cap. Operating Weight (lbs)WA200-8** $530 $1,585 $4,750 126/3.1 26,489 WA250-6 $655 $1,950 $5,840 138/3.0 25,448 WA250-6 High Lift $655 $1,950 $5,840 138/4.0 26,515 WA270-8** $605 $1,810 $5,420 149/3.0 29,388WA320-8** $695 $2,070 $6,200 165/3.7 34,987WA380-8** $1,070 $3,220 $9,670 191/4.0 40,929WA470-8** $1,380 $4,110 $12,316 272/5.5 55,579WA500-7 Yard Loader* $2,500 $7,470 $22,400 357/9.8 80,270WA500-8** — $6,320 $18,940 357/8.0 77,856WA500-8 Yard Loader** $2,625 $7,870 $23,600 357/9.8 81,152WA600-8** — $10,040 $30,080 529/9.2 126,678

*Tier 4 Interim**Tier 4 Final

Model Day Week Four Week TopCon Base & Rover — $2,740

KOMATSU RENTAL EQUIPMENTCRAWLER DOZERS

INTELLIGENT DOZERS

iMC SUPPORT EQUIPMENT

Model Day Week Four Week HP Operating Weight (lbs) D39PXi-24** $1,060 $3,170 $9,500 107 22,774 D51PXi-24** $1,320 $3,950 $11,840 131 31,504D61PXi-24** — $5,180 $15,540 168 42,902D65PXi-18** — $7,030 $21,120 217 50,420 Note: Units with Intelligent technology may require on the job training. The customer is responsible for travel and per diem expenses for this service. Please contact your local dealer for more information.

iMC

GPS

iMCiMCiMC

DUMP TRUCKS

WHEEL LOADERS

1 | 2018 Rental Guide

Model Day Week Four Week Max Dig Operating HP Depth Weight (lbs) PC138USLC-11 Tier 4 Final With 24” shoes, 8’2” arm $825 $2,450 $7,330 18’0” 32,628 97.2 With Hyd. Thumb or Krypto Klaw1 $950 $2,815 $8,390 With NPK GH7 Hammer $1,435* $4,070* $13,070* See page 8 Quick Coupler Charge $70 $195 $575 PC170LC-11 Tier 4 Final With 28” Shoes, 8’7” Arm $760 $2,275 $6,820 19’7” 41,180 121 Optional Arm Size 9’ 6”With Hyd. Thumb or Krypto Klaw1 $840 $2,535 $7,610 With NPK GH7 Hammer $1,405* $4,195* $12,565* See page 8 Quick Coupler Charge $70 $195 $575

PC210LC-11 Tier 4 FinalWith 31.5” Shoes, 9’7” Arm $910 $2,730 $8,180 21’9” 53,882 165With Hyd. Thumb or Krypto Klaw1 $1,030 $3,060 $9,145 With NPK GH9 Hammer $1,655* $4,955* $14,850* See page 8 With NPK GH10 Hammer $1,800* $5,385* $16,110* Quick Coupler Charge $70 $195 $575

PC228USLC-10 Tier 4 Interim With 31.5” Shoes, 9’7” Arm $910 $2,720 $8,160 21’9” 54,405 148 With Hyd. Thumb or Krypto Klaw1 $990 $2,980 $9,125 Quick Coupler Charge $70 $195 $575

*Plus point wear per inch as shown below by model: GH7 $155 GH9 $180 GH12 $230 GH15 $285 GH18 $360

**Plus Edge or Wear Charge1. A Krypto Klaw is a bucket-thumb combo

MINI EXCAVATORSModel Day Week Four Week Max Dig Depth Operating HP Weight (lbs) PC55MR-5 $370 $1,110 $3,140 12’4” 11,618 38.2With Hydraulic Thumb $390 $1,165 $3,315 PC78US-10 $475 $1,415 $4,230 15’ 3” 17,747 54 PC88MR-10 $580 $1,740 $5,200 15’2” 19,290 65 With Hydraulic Thumb $605 $1,810 $5,440

INTELLIGENT EXCAVATORS

HYDRAULIC EXCAVATORS

Model Day Week Four Week Max Dig Depth Operating HP Weight (lbs) PC210LCi-11 Tier 4 Final $1,710 $5,120 $15,340 21’9” 51,588 165 PC360LCi-11 Tier 4 Final — $6,620 $19,850 26’10” 80,547 257 PC390LCi-11 Tier 4 Final — $7,070 $21,200 26’7” 90,441 257 PC490LCi-11 Tier 4 Final — $7,770 $23,310 25’5” 107,850 359 Note: Units with Intelligent technology may require on the job training. The customer is responsible for travel and per diem expenses for this service. Please contact your local dealer for more information.

iMC

iMC

iMC

iMC

Model Day Week Four Week TopCon Base & Rover — — $2,740

iMC SUPPORT EQUIPMENT

GPS QUESTIONS ABOUT iMC? CONTACT YOUR TECHNOLOGY

SOLUTIONS EXPERT (TSE).

2018 Rental Guide | 2

Model Day Week Four Week Max Dig Operating HP Depth Weight (lbs)PC238USLC-11 Tier 4 Final With 31.5” Shoes, 9’6” Arm $960 $2,870 $8,590 21’9” 55,660 165 Quick Coupler Charge $70 $195 $575

PC240LC-10 Tier 4 Interim With 31.5” Shoes, 10’ Arm $970 $2,900 $8,670 22’8” 55,129 177Optional Arm Size 11’ 6”With Hydraulic Thumb $1,075 $3,215 $9,635 Quick Coupler Charge $70 $195 $575

PC240LC-11 Tier 4 Final With 31.5” Shoes, 10’ Arm $1,020 $3,050 $9,130 22’8” 55,000 177Optional Arm Size 11’ 6” With Hydraulic Thumb $1,125 $3,370 $10,095 Quick Coupler Charge $70 $195 $575

PC290LC-11 Tier 4 Final With 31.5” Shoes, 11’6”’ Arm $1,240 $3,705 $11,100 22’8” 68,234 196Optional Arm Size 10’ 6”With Hyd. Thumb or Krypto Klaw1 $1,360 $4,040 $12,065

PC290LC-11 Long Front $1,530 $4,580 $13,725 68,260 196 (Less bucket)PC360LC-10 Tier 4 Interim With 33.5” Shoes, 13’2” Arm — $4,190 $12,570 34’7” 79,930 257Optional Arm Size 10’ 5”With Genesis GXP660R Shear — — $31,320** 99,633 With Genesis LXP300 Multi Jaw Processor — $31,070** 87,300 With Genesis GDR300 Processor — — $21,030** 87,537With Hyd. Thumb or Krypto Klaw1 — $4,545 $13,720 82,037With NPK GH12 Hammer — $7,590* $22,755* 85,287With NPK GH15 Hammer — $7,910* $23,715* 82,192Additional Charge for Quick Coupler — $365 $1,090

PC360LC-11 Tier 4 Final With 33.5” Shoes, 13’2” Arm — $4,430 $13,270 26’10” 80,547 257 Optional Arm Size 10’ 5”With Genesis GXP660R Shear — — $32,020** With Genesis LXP300 Multi Jaw Processor — $31,770** With Genesis GDR300 Processor — — $21,700** With Hyd. Thumb or Krypto Klaw1 — $4,815 $14,420 With NPK GH12 Hammer — $7,830* $23,905* With NPK GH15 Hammer — $8,150* $24,415* Additional Charge for Q.Coupler — $365 $1,090 *Plus point wear per inch as shown below by model: GH7 $155 GH9 $180 GH12 $230 GH15 $285 GH18 $360

**Plus Edge or Wear Charge 1. A Krypto Klaw is a bucket-thumb combo


KOMATSU RENTAL EQUIPMENT


Model Day Week Four Week Max Dig Operating HP Depth Weight (lbs)PC390LC-11 Tier 4 Final With 33.5” Shoes, 13’2” Arm — $4,790 $14,360 26’7” 90,441 257 Optional Arm Size 10’ 5”With Genesis GXP660R Shear — — $33,110** 105,541 With Genesis GDR300 Processor — — $30,570** 98,341 With Genesis LXP300 Multi Jaw Processor — $32,860** See Page 8 With Hyd. Thumb or Krypto Klaw1 — $5,175 $15,510 With NPK GH15 Hammer — $8,510* $25,505* 96,708

PC490LC-10 Tier 4 Interim With 35.5” Shoes, 13’1” Arm — $5,530 $16,560 27’6” 109,250 359 Optional Arm Sizes 11’1” or 15’9”With Hyd. Thumb or Krypto Klaw1 — $5,920 $17,730 112,050With NPK GH18 Hammer — — $33,110* 117,050

PC490LC-11 Tier 4 Final With 35.5” shoes, 11’1” arm — $5,820 $17,430 25’ 5” 107,850 359Optional Arm Sizes 13’1” or 15’9”With Hydraulic Thumb — $6,030 $18,060 111,650With NPK GH18 Hammer — — $33,980* 115,650

PC650LC-11 Tier 4 Final With 36” shoes, 17’1” arm — — $27,580 34’ 9” 145,284 392Optional Arm Size 14’ 1” PC800LC-8 Tier 3 40” track with 18’4” arm — — $32,450 34’ 9” 184,530 487

PC390LC-11 Long Front — $5,460 $16,380 90,357 257 (Less bucket)*Plus point wear per inch as shown below by model: GH7 $155 GH9 $180 GH12 $230 GH15 $285 GH18 $360

**Plus Edge or Wear Charge1. A Krypto Klaw is a bucket-thumb combo

For more information on Genesis & NPK attachments, see page 8 & 9.

Model Day Week Four Week Max Capacity Operating Weight (lbs) YB7725* $695 $2,090 $6,280 25 Ton 45,000Boom: 73 ftRT650E* $1,120 $3,370 $10,090 50 Ton 77,000Boom: 105 ftRT765E-2* $1,510 $4,510 $13,520 65 Ton 93,000Boom: 110 ft

*Northern Minnesota Only

Note: Crane erection and dismantle is customer’s responsibility. Call RMS Service for quote if assistance is needed.

CRANESHYDRAULIC ROUGH TERRAIN CRANES*



Model Day Week Four Week Working Width Operating Weight (lbs) RW35A — $2,360 $7,070 1.5’-4’ 7,000

Model Day Week Four Week Working Width Operating Weight (lbs)PT125C $420 $1,260 $3,760 68” 9,540 PT240R — $2,260 $6,750 78” 36,218

Model Day Week Four Week Belt Drive Operating Weight (lbs)11-3060 — — $2,290 30” X 60’ Hyd 15,00011-3660 — — $2,350 36” X 60’ Elect 18,000

Model Day Week Four Week Drum Width Operating Weight (lbs)DD25B - 39” $180 $535 $1,590 39” 5,545CC1200 $210 $665 $1,850 47” 5,735CC1200C $225 $670 $2,010 47” Combi 5,400 DD25B - 47” $220 $665 $2,000 47” 5,776DD30B $210 $615 $1,830 49.2” 6,839DD35B $270 $805 $2,400 54.1” 8,195CC4200 $645 $1,920 $5,760 68” 20,900CC6200 $825 $2,470 $7,400 84” 24,460

Please call 952-895-9595 or contact your territory sales representative for milling options.

MILLING

ASPHALT ROLLERS

PNEUMATIC TIRE ROLLERS

AGGREGATECONVEYORS

ROAD WIDENERS


Model Day Week Four Week Drum Width Operating Weight (lbs)CA1300/SD45D $405 $1,205 $3,600 54” 10,600CA1300PD/SD45D/F $435 $1,290 $3,845 54” 11,350* CA1500/SD75D, ROPS $555 $1,650 $4,930 66” 16,596CA1500/SD75D, CAB $695 $2,090 $6,240 66” 18,596 CA1500PD/SD75F, ROPS $610 $1,820 $5,440 66” 17,395CA1500PD/SD75F, CAB $775 $2,310 $6,920 66” 19,395CA3500/SD115D, ROPS $775 $2,315 $6,940 84” 23,930CA3500/SD115D, Cab $800 $2,390 $7,160 84” 26,000CA3500PD/SD115DF or F, ROPS $800 $2,390 $7,160 84” 23,930*CA3500PD/SD115DF or F, Cab $905 $2,710 $8,125 84” 26,000*

*Add additional 3,000# for Bolt-on Pad foot kit.

ROAD WORKSOIL COMPACTORS

Model Day Week Four Week Belt Drive Operating Weight (lbs)11-3670 — — $2,625 36” X 70’ Elect 18,15013-3080H — — $2,895 30” X 80’ Hyd 18,100 13-3080 — — $2,910 30” X 80’ Hyd 20,00013-3680 — — $3,010 36” X 80’ Elect 21,00031-3080 — — $3,270 30” X 80’ Elect 18,700 13-3680SC — — $4,350 36” X 80’ Diesel/Hyd King Pin Weight: 3,900 Self Contained Axle Weight: 15,400 13-4280 — — $4,645 42” X 80’ Elect 24,70013-36100 — — $5,540 30” X 100’ Elect 23,00013-36125 — — $8,040 36” X 125’ Elect 43,00013-36150 — — $9,800 36” X 150’ Elect 52,100 13-42125 — — $8,550 42” X 125’ Elect 5,00033-36136LP — — $12,780 36” X 136’ Elect 54,220Super Stacker 33-36150 — — $11,210 36” X 150’ Elect King Pin Weight: 26,000 Super Stacker Axle Weight: 40,00047-3670 — — $7,280 (3) 36” x 70’ Elect King Pin Weight: 12,500 Rollpack transfer conveyor Axle Weight: 22,10047-4270 — — $8,370 (3) 42” x 70’ Elect King Pin Weight: 15,800 Rollpack transfer conveyor Axle Weight: 27,200

CONVEYORS

Model Day Week Four Week Decks/Drive Operating Weight (lbs)CS3055, Primary Jaw Plant — — $28,500 Jaw/Elect King Pin weight: 50,000 Axle weight: 78,000

Model Day Week Four Week Belt Drive Operating Weight (lbs)942-18-20 — — $9,300 20 Ton Hopper 27,000 with 6# grizzly

Model Day Week Four Week Decks/Drive Operating Weight (lbs)1830PH — — $20,850 (3) 6’ X 20’/Elect 80,0006036-19 — — $2,650 36’ x 30’ 10,400Single Course Material

Model Day Week Four Week Decks/Drive Operating Weight (lbs)GT104 — — $8,760 (2) 4’ x 9’/Diesel 36,000 PTSC2618VM — — $10,200 (2) 6’ x 18’/Electric 28,000High Frequency Screen 2512K — — $15,150 (2) 5’ X 12’/Diesel 57,400Fold N Go Screen Plant6203 — — $12,150 (3) 6’ X 20’ 49,000 3-deck Horizontal w/two cross conveyors and switch gear7203 — — $14,250 (3) 7’ X 20’ 51,000 3-deck Horizontal w/two cross conveyors and switch gearGT145 S — — $14,280 5’ x 14’ 3 deck 71,000 Mobile Track, Diesel Power GT165DF — — $13,910 (2) 5’ x 16’ 75,000GT205 S — — $13,700 5’ x 20’ 2 deck 82,800Mobile Track, Diesel Power

FEED HOPPER

WASH PLANT

SCREEN PLANTS

CRUSHERS


Model Day Week Four Week Broom Width Operating Weight (lbs)RCT350 $460* $1,140* $3,370* 8’ 5,000With Cab & A/C *Plus $80 per inch broom wear

Model Day Week Four Week Capacity T4223 — — $3,140 23 Cy T4021 — — $3,500 21 Cy

Note: Not for rip rap or demolition debris use

OTHER EQUIPMENT

BROOMS/SWEEPERS

BOTTOM DUMP TRAILERS

Model Day Week Four Week Capacity RSD4224 — — $3,550 24.5 Yd

Note: Not for rip rap or demolition debris use

SIDE DUMP TRAILERS


AGGREGATE

Model Day Week Four Week Decks/Drive Operating Weight (lbs)FT4250, Close CircuitedTrack Impactor** — — $32,950 HSI/Diesel 120,000Minimum training of 1 day, instructed by RMS, required for FT4250. See note below for details.FT2650 Jaw CrusherMobile Track Plant — — $30,375 Jaw/Diesel 110,000 CH440 Cone Crusher** — — $28,300 King Pin Weight: 23,400 Axle weight: 51,760 CH660 Cone Crusher** — — $35,360 Twin 200 HP Electric King Pin Weight: 44,800 Axle Weight: 73,200 K200/6203** — — $35,260 3/Electric K200 King Pin Weight: 59,000Cone Plant w/Screen Quad Axle Weight: 62,000

K300 — — $26,000 - /Electric K200 King Pin Weight: 41,000 Est.In/Out Cone Crusher Quad Axle Weight: 42,000 Est.

**Requires a minimum 3 month rental commitment. Training: It is the customer’s responsibility to ensure that all operators of aggregate equipment are properly trained. If the customer does not have adequately trained personnel, RMS can provide 1-2 day training at start-up @ $1,500/day. Note: Aggregate equipment rental rates do not include screen cloths or crushing wear items, which will be billed out on return of equipment. The FOB point for all aggregate equipment (excluding conveyors) will be the originating RMS aggregate branch. Aggregate branches are: Savage, Duluth and Virginia, MN as well as East Moline, IL.

CRUSHERS

Model Day Week Four Week Working Operating Max. Load (lbs) Width Weight (lbs)MST-700VD — $1,710 $5,140 7’ 4” 13,000 9,479 MST-800VD — $2,280 $6,850 8’ 14,140 10,584MST-1500VD — $2,720 $8,160 8’ 6” 22,040 15,435MST-1500VDR — $3,630 $10,880 8’ 6” 28,100 15,435MST-2200VD — $3,270 $9,800 9’ 7” 31,820 24,225 MST-2200VDR — $4,380 $13,130 9’ 8” 35,273 24,255

Model Day Week Four Week Impulse Force Operating Weight (lbs) C4C $115 $335 $990 7,800 Ft. lbs. 960 C6C $145 $425 $1,260 16,000 Ft. lbs. 1,650C8C $270 $810 $2,405 24,000 Ft. lbs. 2,325 C10C $300 $885 $2,650 34,000 Ft. lbs. 3,530

SCRAP/DEMOLITIONRUBBER TRACK CARRIERS

HYDRAULIC COMPACTORS

Model Day Week Four Week Impact Class Operating Weight (lbs) PH-3 Fits PC55/PC88 $275 $835 $2,510 750 Ft. lbs. 800PH-4 Fits PC88 $290* $865* $2,590* 1,300 Ft. Ibs. 1,025*Plus $105 per inch point wear Note: To avoid damage or breakage to the hammer, regular greasing of the hammer chisel is required (every 1-3 hours). Chisel tool damage is the lessee’s responsibility.

GH-6 Fits PC138 $580 $1,735 $5,200 2,000 Ft. lbs. 2,390 GH-7 Fits PC138/PC170 $645* $1,920* $5,745* 2,500 Ft. lbs. 2,965*Plus $155 per inch point wear GH9 Fits PC210/PC240 $745 $2,225 $6,670* 3,000 Ft. lbs. 3,542*Plus $180 per inch point wearGH10 Fits PC210/PC240 $890 $2,655 $7,960* 4,000 Ft. lbs. 4,003*Plus $180 per inch point wearGH12 Fits PC290/PC360 $1,135 $3,400 $10,185* 5,500 Ft. lbs. 5,092*Plus $230 per inch point wearGH15 Fits PC360/PC390 $1,245 $3,720 $11,145* 8,000 Ft. lbs. 6,267*Plus $285 per inch point wearGH18 Fits PC490 $1,845 $5,520 $16,550* 12,000 Ft. lbs. 7,257*Plus $360 per inch point wear Note: 4 Tubes of grease will be consigned to hammer rents for use with auto lube. All grease tubes that were used will be charged at $13.00/ea. upon return. Chisel tool damage is the lessee’s responsibility.

HYDRAULIC HAMMERS



Model Day Week Four Jaw Opening/ Operating Week Jaw Depth Weight (lbs)LXP300 — — $18,500* Pulverizer: 23”/24” 7,270Fits PC300LC-PC390LC Shear: 22”/24” 7,600 Cracker: 43”/30” 7,560

* All shears will be sent out with new knife edges. Wear charge on return is $975 per edge set plus build up and wear items.

Note: All attachments for the multi-jaw processors will be provided with the rent including the stands.

Model Day Week Four Jaw Opening/ Operating Week Jaw Depth Weight (lbs)GCP410 — — $8,910 34” / 29” 4,650Minimum excavator weight 45,000 lbsGDT290 — $2,590* $7,765* 39” / 42” 7,000 Minimum excavator weight 60,000 lbsGDT390 — $3,355* $10,052* 46” / 45” 10,000Minimum excavator weight 90,000 lbsGDR300 — $2,825* $8,460* 43” / 39” 7,900 Minimum excavator weight 70,000 lbs GDR400 — $3,665* $10,990* 48” / 41” 11,000 Minimum excavator weight 100,000 lbsGHG125 — — $6,160* 87” / 28” 4,900 * All Genesis attachments will be sent out with new knife edges. Wear charge on return is $975 per edge set plus build up and wear items. **Plus stiff arm pad charge - $500

MULTI JAW PROCESSORS*

CONCRETE PROCESSORS

SCRAP/DEMOLITION

Model Day Week Four Jaw Jaw Operating Week Opening Depth Weight (lbs)GXP660R — — $18,750* 32” 32” 15,500 Fits PC360 GXT445R — — $13,260* 28” 28” 11,000Fits PC210GXT555R — — $16,370* 30” 30” 13,100 Fits PC290GXT775R — — $21,640* 35” 37” 17,750Fits PC390

*All shears will be sent out with new knife edges. Wear charge on return is $975 per edge set plus build up and wear items.

MOBILE SHEARS

1. CREDIT - All rentals require a customer to have an open account and are subject to approval by our credit department. Customer is responsible for payment of late fees for overdue accounts.

2. INSURANCE A. Liability: proof of General Liability insurance must be provided to RMS prior to taking possession of equipment. The minimum liability coverage amount is $1,000,000 per occurrence, with RMS named as an additional insured. B. Physical Damage: proof of physical loss insurance is required for the value of each piece of equipment rented. A damage waiver for physical loss can be provided by RMS at an additional cost of 12% of the rental rate.

3. CONTRACT: A rental contract must be signed for each separate order of rental equipment by the customer. In addition, the renter is required to provide complete job site information where equipment will be located including the job number and corresponding bond information, if applicable. Renter is responsible to notify RMS of any/all job or location changes of the rented equipment.

4. USE: Customer will ensure that operators and any personnel hired to haul equipment are familiar with the operation of the rental equipment and have read the operator’s manual. If the operator or customer has any questions regarding the proper operation or maintenance procedures, they should contact the RMS service department at 952-895-9595.

5. RATES: Rates shown in this publication do not include sales tax or damage waiver coverage. Rates are based as follows:- Daily - 8 hours- Weekly - 40 hours or 5 days- 4 Weeks - 176 hours- Any overtime hours will be prorated at 70% of the normal rental rate.

6. HAULING - Customer is responsible for all hauling charges to and from job sites.

7. REPAIRS & MAINTENANCE: While the units are in the possession of the renter, renter is responsible for normal preventative maintenance, as required by the manufacturer. Such items include oil changes, filter changes, greasing, etc. Customers will be assessed a per hour charge for their prorated change of oil and filter costs if performed by RMS during the rental period or on return of the unit.

Any damage to the equipment due to renter abuse or negligence will be charged to the lessee on return of the rental equipment.

8. ADDITIONAL RESPONSIBILITIES-RENTER: Ensure that equipment is properly secured to transport vehicles. Observe legal weights and dimensions.

Authorize transportation provider to sign shipping papers, checkout/in forms and safety checklists. Charges for abnormal tire wear including cuts, abrasions, and punctures.

Charges for manuals or keys not returned.Returning machine with full fuel tank or paying for fuel used.

Cleaning labor in excess of 1 hour, which would include shoveling of tracks.

Excess wear on ground engaging tools, wear items, and undercarriage.

Additional charges as listed on the rental rate sheet for type of equipment rented.

Note: Please note that on the previous rate pages, the operating weight provided is an estimate and will vary depending on equipment options. Rental rates are subject to change.

RENTAL TERMS & POLICIES


Documents

2018 Rental GUIDE - rmsequipment.com · With NPK GH15 Hammer — $8,150* $24,415* Additional Charge for Q.Coupler — $365 $1,090 *Plus point wear per inch as shown