52002 Magnetic dish 52000 - HOMMEL HERCULES

ß Hand tools

eng/OP www.hhw.de 52.1

5

Magnetic dish

TypeRound, made of stainless steel. Thanks to themagnetic effect on both sides, the magnetic dishcan be attached to all iron materials such as toolcarts, tool panels, or lifting platforms. The bottom ofthe dish is rubber-coated, in order to protect thesurfaces.

ApplicationMulti-purpose magnetic dish with strong magnet,which secures small parts such as screws or wheelbolts.

52002

Permanent magnetising and demagnetising instruments

+TypeHousing made of rigid plastics, cadmium-free.

ApplicationFor magnetising and/or demagnetising of screwdri-ver blades, tweezers and similar tools made of steel.

52000

52000 …

101

52000

Ø 52002 …mm150 101

52002

Set of magnetic rubber rings

TypeThe magnetic system consists of a flexible rubberring. The magnets are built in in the face. Set of 4pcs.ApplicationThe rubber ring slides along the tool. Therefore, the

rubber ring can be adjusted to the screw, or if nomagnet is neccessary, the ring can be removed orpushed onto the shank. For slotted screws, Phillips,hexagonal head, TORX® and Trisquare wrenches.

52003

Ring sizessuitable for: Size 1 Size 2 Size 3 Size 4

Allen key 3 + 4 5 6 + 7 8 + 9T profile 15, 20, 25 27 + 30 40 + 45 50

Trisquare – 5 + 6 8 10

Set 52003 …

4-part 101

52003

Set of extra small screwdrivers

TypeDIN 8320 BS1. Handles made of impact-proofplastic, handle end rotatable.QualityBlade made of chrome-vanadium steel, harde-ned and burnished.

52004 101In plastic case.

52004 102In wooden case.

52004 101

Set contents Cutting edge width x Overall length 52004 …mm

5-part 1,0 x 104 / 1,4 x 104 / 1,8 x 104 / 2,3 x 104 / 3,0 x 104 1017-part 0,6 x 104 / 0,8 x 104 / 1,0 x 104 / 1,2 x 104 / 1,4 x 104 / 1,8 x 104 / 2,3 x 104 102

52004

Extra small screwdriver

TypeSimilar to DIN 8320. Blade hardened, with fluted,nickel-plated steel handle, revolving handle end. Setin wooden box.

QualityBlade made of chrome-vanadium steel. 52005

Set contents cutting edge width x Overall length 52005 …mm

6-part 1,0 x 83 / 1,5 x 87 / 1,8 x 101 / 2,3 x 104 / 3,0 x 117 / 3,5 x 117 101

52005 - 52009

Cutting edge width x thickness Handle Ø Overall length 52009 …mm mm mm

1,0 x 0,20 4 83 1011,5 x 0,23 4 87 1021,8 x 0,30 6 101 103

Cutting edge width x thickness Handle Ø Overall length 52009 …mm mm mm

2,3 x 0,30 6 104 1043,0 x 0,50 8 117 1053,5 x 0,60 8 117 106

eng/OP

• Multi-purpose screwdrivers • Workshop screwdrivers

www.hhw.de52.2

5

Multi-purpose screwdrivers

Type4 blades, hardened, exchangeable, in handle, shankmade of brass, nickel-plated, handle fluted.QualityBlade made of chrome-vanadium steel.

52015

Cutting edge width x thickness Handle Ø Overall length 52015 …mm mm mm1,5 x 0,23 / 2,0 x 0,4 / 2,5 x 0,4 / 3,0 x 0,5 8,5 115 101

52015

Workshop screwdrivers

ßTypeOutput: DIN 5264 A, ISO 2380. Round blade,hardened, with nicromatt surface, non-dazzle andnon-peeling, Black Point tip and Kraftform handlewith roll stop.

QualityBlade made of high-alloyed special vanadiumsteel.

Note:Blade width 3,0 and 4,0mm with identical blade andshank diameter.

52050

Set contents Cutting edge width x blade length 52050 …mm

6-part 3,0 x 80 / 4,0 x 100 / 5,0 x 100 / 6,0 x 125 / 7,0 x 150 / 10,0 x 200 101

Cutting edge width x thickness Blade length Overall length 52060 …mm mm mm

5,0 x 0,8 100 198 1016,0 x 1,0 125 223 1027,0 x 1,2 150 248 103


8,0 x 1,2 175 287 10410,0 x 1,6 200 312 105

52050 - 52060

Stubby screwdrivers (carburettor screwdrivers)

ßTypeSquare blade for using a wrench, with nicromattsurface, dazzle-free and non-peeling, red Kraftformhandle.



5,5 x 1,0 25 79 101L 5,5 x 1,0 45 99 102


6,5 x 1,2 25 79 103L 6,5 x 1,2 45 99 104

52372

52372


0Type Round blade, full-hardened, glossy nickel-plated.Multi-component handle with extra large softzone and attachment eye.

Quality Blade made of chrome-vanadium steel.

Note: Blade width 3,0 and 4,0mm with identical blade andshank diameter.

52065

Set contents Cutting edge width x blade length 52065 …mm

6-part 3,0 x 80 / 4,0 x 100 / 5,5 x 125 / 6,5 x 150 / 8,0 x 175 / 10,0 x 200 101


4,5 x 0,8 100 207 1015,5 x 1,0 125 232 1026,5 x 1,2 150 269 103


8,0 x 1,2 175 294 10410,0 x 1,6 200 319 105

52065 - 52066

ß Hand tools


5


+TypeRound blade, glossy nickel-plated, full-hardened,with impact-proof, transparent square end handlemade of cellulose acetate, red.

QualityBlade made of chrome-vanadium-molybdenumsteel.

Note:Starting at 5,5mm blade width, corrugated tipagainst slipping.

52108

Set contents Cutting edge width x Blade length 52108 …mm

6-part 2,5 x 75 / 3,5 x 90 / 4,5 x 100 / 5,5 x 120 / 7,0 x 140 / 9,0 x 160 101


2,5 x 0,4 75 150 1013,5 x 0,5 90 175 1024,5 x 0,7 100 195 103

5,5 x 0,95 120 225 104


7,0 x 1,05 140 255 1059,0 x 1,2 160 275 106

10,0 x 1,4 180 305 107

52110

52108 - 52110


+TypeOutput: DIN 5265, ISO 2380. Round blade, full-hardened, with matt-chrome finish. ChromTop tip.SoftFinish® handle with roll stop.

QualityBlade made of high-quality chrome-vanadium-molybdenum steel.

52120 208-221


4,0 x 0,8 100 211 2085,5 x 1,0 125 236 2136,5 x 1,2 150 268 218

L 8,0 x 1,2 175 299 221


4,0 x 0,8 25 81 2305,5 x 1,0 25 81 2316,5 x 1,2 25 81 2328,0 x 1,2 25 81 233

52120 230-233

52120

52125 201-206

52125 208-209


sTypeOutput: DIN 5264 A, ISO 2380. Round blade,nicromatt, with Lasertip and Kraftform handle withroll stop.

QualityBlade made of 73 Mo V 5 2. 52123


5,0 x 0,8 100 198 1016,0 x 1,0 125 230 1026,5 x 1,2 150 255 103


7,0 x 1,2 150 255 1048,0 x 1,2 175 287 105

10,0 x 1,6 200 312 106

52123


,TypeOutput: DIN 5264 A, ISO 2380-1 A.Round blade, full-hardened, matt-chrome finish,burnished tip. Ergonomic 3-component handle,impact-proof. Permanent colour coding on bothhandle ends (for slotted screws = yellow).

QualityBlade made of vanadium-extra steel.

52125 207


2,5 x 0,4 75 197 2013,0 x 0,5 75 197 202

L 3,0 x 0,5 125 247 2033,5 x 0,6 75 197 204

L 3,5 x 0,6 125 247 205


4,0 x 0,8 100 222 2065,5 x 1,0 150 272 2076,5 x 1,2 150 272 2088,0 x 1,6 175 297 209

52125

eng/OP

• Workshop screwdrivers

www.hhw.de52.4

5

Stubby screwdrivers (carburettor screwdrivers)

,TypeOutput: DIN 5264 A, ISO 2380-1 A.Round blade, full-hardened, matt-chrome finish,burnished tip. Ergonomic 3-component handle,impact-proof. Permanent colour coding on bothhandle ends (for slotted screws = yellow).


52376

52376


+TypeRound blade, glossy nickel-plated, full-hardened,with handle made of hardwood, beechwood,lacquered. Impact head with leather cap, thereforeno damage to end of handle.

QualityBlade made of chrome-vanadium steel.

Note:Starting at 5,5 mm blade width full-length blade,hexagonal shoulder on tang for using a wrench andcorrugated tip against slipping.

52138


5-part 3,5 x 75 / 4,5 x 90 / 5,5 x 100 / 7,0 x 125 / 9,0 x 150 101

52138 - 52140


3,5 x 0,6 75 175 1014,5 x 0,8 90 190 102

5,5 x 0,95 100 205 1037,0 x 0,95 125 230 104


9,0 x 1,1 150 270 10510,0 x 1,2 175 295 10612,0 x 1,4 200 325 107

14,0 x 1,75 250 380 108


3,5 x 0,6 25 83 2014,0 x 0,8 25 83 2025,5 x 1,0 25 83 203


6,5 x 1,2 25 83 2058,0 x 1,2 25 83 207


ßTypeOutput: DIN 5264 A, ISO 2380.Full-length hexagonal blade with impact plate,hexagonal shoulder on tang for using a wrench (4,5mm without). Blade hardened throughout, withnicromatt surface, non-dazzle and non-peeling,Black Point tip and Kraftform handle with roll stop.


Note:Starting at 5,5 mm blade width: with temperedhexagonal shoulder on tang for using a wrench.

52148


5-part 3,5 x 75 / 4,5 x 90 / 5,5 x 100 / 7,0 x 125 / 9,0 x 150 101

52148 - 52150


3,5 x 0,6 75 156 1014,5 x 0,8 90 171 1025,5 x 1,0 100 198 1037,0 x 1,2 125 223 104


9,0 x 1,6 150 262 10510,0 x 1,6 175 287 10612,0 x 2,0 200 312 10714,0 x 2,5 250 367 108


0Type Output: DIN 5625, ISO 2380. Hexagonal blade with hexagonal shoulder on tangfor using a wrench, full-hardened, matt-chrome

finish, blackened tip. Multi-component handle with extra large softzone and attachment eye. Quality Blade made of chrome-vanadium-molybdenumsteel.

52152

Cutting edge width x Blade length Overall length 52152 …mm mm

3,5 x 75 165 1014,5 x 90 190 102

5,5 x 100 212 1036,5 x 125 237 104

Cutting edge width x Blade length Overall length 52152 …mm mm

8,0 x 150 262 10510,0 x 175 287 10612,0 x 200 312 107

52152

ß Hand tools


5


+Type Output: DIN 5265, ISO 2380. Hexagonal blade with hexagonal shoulder on tangfor using a wrench, full-hardened, matt-chromefinish. ChromTop tip. SoftFinish® handle with rollstop.

Quality Blade made of high-quality chrome-vanadium-molybdenum steel.

52151


3,5 x 0,6 75 186 1014,5 x 0,8 90 201 1025,5 x 1,0 100 213 1036,5 x 1,2 125 238 1047,0 x 1,1 125 238 105


8,0 x 1,2 150 268 1069,0 x 1,4 150 268 107

10,0 x 1,6 175 293 10812,0 x 2,0 200 318 10914,0 x 2,5 250 368 110

52151


+Type Output: DIN 5265, ISO 2380. Hexagonal blade with hexagonal shoulder on tangfor using a wrench, full-hardened, matt-chromefinish. ChromTop tip. SoftFinish® handle with rollstop and steel plate.

Quality Blade made of high-quality chrome-vanadium-molybdenum steel.

52153


3,5 x 0,6 75 186 2014,5 x 0,8 90 201 2025,5 x 1,0 100 213 2036,5 x 1,2 125 238 204


8,0 x 1,2 150 271 20510,0 x 1,6 175 296 20612,0 x 2,0 200 321 20714,0 x 2,5 250 371 208

52153

Workshop screwdriver/The chisel-screwdriver

sTypeOutput: DIN 5264 A, ISO 2380.Full-length hexagonal blade with impact plate andhexagonal shoulder on tang for using a wrench(starting at 4,5 x 0,8 mm). Black Point tip, exceptio-nally tough tempered. Soft zone Kraftform® handlewith roll stop.

QualityBlade made of 73 Mo V 5 2.

Note:Blade length 200 and 250 mm handle made of one-component material w/o. soft zones.

52154


3,5 x 0,6 80 161 1014,5 x 0,8 90 188 1025,5 x 1,0 100 205 1037,0 x 1,2 125 230 104


9,0 x 1,6 150 262 10510,0 x 1,6 175 287 10612,0 x 2,0 200 317 10714,0 x 2,5 250 319 108

52154


sType Output: DIN 5264 A, ISO 2380.With Lasertip. Hexagonal blade, nicromatt,hexagonal shoulder on tang for using a wrench(starting at 4,5 x 0,8 mm) and soft zone Kraftform®

handle with roll stop.



3,5 x 0,6 75 156 1014,0 x 0,8 90 171 1024,5 x 0,8 90 188 1035,5 x 1,0 100 198 104


6,5 x 1,2 125 230 1057,0 x 1,2 125 230 1069,0 x 1,6 150 262 107

10,0 x 1,6 175 287 108

52156

eng/OP

• Workshop screwdrivers • Electrician’s screwdrivers • ESD/EGB screwdrivers

www.hhw.de52.6

5


,TypeOutput: DIN 5264-A ISO 2380-1-A.Hexagonal blade, full-hardened, matt-chromefinish, burnished tip. Hexagonal shoulder on tang forusing a wrench. Ergonomic 3-component handle,

impact-proof. Permanent colour coding on bothhandle ends (for slotted screws = yellow).QualityBlade made of vanadium-extra steel.

52157 201-203

52157 204-205


5,5 x 1,0 125 247 2016,5 x 1,2 150 272 2028,0 x 1,6 175 297 203


10,0 x 1,6 175 336 20412,0 x 2,0 200 361 205

52157

Electrician’s screwdrivers

ßTypeOutput: DIN 5264 A, ISO 2380.Round blade, hardened, with nicromatt surface,non-dazzle and non-peeling, Black Point tip and

Kraftform handle with roll stop. With constant bladewidth and blade diameter.QualityBlade made of high-alloyed special vanadiumsteel.

52158


2,5 x 0,4 50 120 1013,0 x 0,5 80 150 1033,5 x 0,6 125 205 105


4,0 x 0,8 100 180 1075,5 x 1,0 125 205 111

L 5,5 x 1,0 200 280 113

52158 - 52160


5-part 2,5 x 50 / 3,0 x 80 / 4,0 x 100 / 5,5 x 125 / 5,5 x 200 101


sTypeOutput: DIN 5264 A, ISO 2380.Round blade, nicromatt, with Lasertip (size 3,5 -5,5 mm) and soft zone Kraftform® handle with rollstop. With constant blade width and blade diameter.


52168Note:Blade length 300mm with handle made of one-com-ponent material without soft zones and withoutLasertip®.

52168

52165 - 52168


0Type Round blade, full-hardened, glossy nickel-plated.Multi-component handle with extra large soft

zone and attachment eye. With constant blade widthand blade diameter. Quality Blade made of chrome-vanadium steel.

52162


2,5 x 0,4 75 161 1013,0 x 0,5 80 166 1023,5 x 0,6 100 197 1034,0 x 0,8 100 207 104

L 4,0 x 0,8 150 257 105


XL 4,0 x 0,8 200 307 1065,0 x 0,9 100 207 1075,5 x 1,0 200 232 1086,0 x 1,1 150 269 109

52162


2,0 x 0,4 60 141 1002,5 x 0,4 60 141 101

L 2,5 x 0,4 75 156 1023,0 x 0,5 80 161 1033,5 x 0,6 100 181 104

L 3,5 x 0,6 125 206 105XL 3,5 x 0,6 200 281 106


4,0 x 0,8 100 198 107L 4,0 x 0,8 150 248 108

XXL 4,0 x 0,8 300 398 1105,5 x 1,0 125 223 111

L 5,5 x 1,0 150 248 112XXL 5,5 x 1,0 300 398 114


5-part 2,5 x 75 / 3,0 x 80 / 4,0 x 100 / 5,5 x 125 / 5,5 x 200 101

ß Hand tools


5

ESD/EGB screwdrivers

sTypeOutput: DIN 5264, ISO 2380.Round blade, Black-Point tip, ergonomicallyoptimised Kraftform® handle with roll stop.

ApplicationFor application with electronic construction partswith risk of electrostatics. Fulfils standard EN 100-015 part 1.QualityBlade made of high-alloyed special steel.

52169


5,5 x 1,0 200 298 2046,0 x 1,0 125 223 2056,5 x 1,2 150 248 206


7,0 x 1,2 150 262 2078,0 x 1,2 175 287 208

52169

VDE electrician’s screwdrivers

ßTypeOutput: DIN 5264 A, ISO 2380. Routine-tested incompliance with VDE 0680/T201, IEC 900, normDIN 7437, Black-Point tip and Kraftform handle,conical blade.

QualityBlade burnished, insulated. 52170


5-part 2,5 x 80 / 4,0 x 100 / 5,5 x 125 / 6,5 x 150 / 8,0 x 175 101


2,5 x 0,4 80 150 1023,0 x 0,5 100 175 1033,5 x 0,6 100 180 1044,0 x 0,8 100 190 105


5,5 x 1,0 125 225 1066,5 x 1,2 150 250 1078,0 x 1,2 175 285 108

52170 - 52175


0Type Output: DIN 5264, ISO 2380. Routine-tested incompliance with DIN EN 60900 (IEC 900),

standard DIN 7437.QualityBlade burnished, insulated.

52180


5-part 2,5 x 75 / 4,0 x 100 / 5,5 x 125 / 6,5 x 150 / 8,0 x 175 101


2,5 x 0,4 75 161 1023,0 x 0,5 100 186 1033,5 x 0,6 100 197 1044,0 x 0,8 100 207 105


5,5 x 1,0 125 244 1066,5 x 1,2 150 269 1078,0 x 1,2 175 294 108

10,0 x 1,6 200 319 110

52180 - 52181


3,5 x 0,6 100 204 1014,0 x 0,8 100 211 1025,5 x 1,0 125 243 1036,5 x 1,2 150 268 104

VDE electrician’s screwdrivers52320

+TypeOutput: DIN 5264, ISO 2380.Routine-tested, IEC 60900:2004.SoftFinish® handle with roll stop. The protectiveinsulation is completely integrated in the front part ofthe blade. 38 mm constant thin diameter: thisensures that screws or springs can be reached evenin hard-to-reach places.

QualityBlade made of chrome-vanadium-molybdenumsteel, full-hardened, burnished. 52320

eng/OP

• Electrician’s screwdrivers • Phillips screwdrivers PH

www.hhw.de52.8

5


+TypeOutput: DIN 5264, ISO 2380.Routine-tested, DIN EN 60900 (IEC 900). SoftFi-nish® handle with roll stop.

QualityBlade made of chrome-vanadium-molybdenumsteel, full-hardened, burnished.

52323


5-part 2,5 x 75 / 4,0 x 100 / 5,5 x 125 / 6,5 x 150 / 8,0 x 175 101


2,5 x 0,4 75 179 1023,5 x 0,6 100 204 1044,0 x 0,8 100 211 1054,5 x 1,0 125 236 106


5,5 x 1,0 125 243 108L 5,5 x 1,0 175 293 109

6,5 x 1,2 150 268 1118,0 x 1,2 175 299 112

52323 - 52324


+TypeOutput: DIN 5264, ISO 2380.Routine-tested, DIN EN 60900 (IEC 900), DIN

7437. Impact-proof, chemicals and oil-resistantsquare handle.QualityBlade made of chrome-vanadium steel, full-har-dened, burnished.

52325


2,3 x 0,5 60 135 1012,5 x 0,4 75 150 1022,8 x 0,6 75 150 1033,0 x 0,5 100 175 104

L 3,0 x 0,5 150 225 1053,5 x 0,6 100 185 1063,5 x 0,8 100 185 1074,0 x 0,8 100 195 108

L 4,0 x 0,8 150 245 109


4,5 x 1,0 125 220 1105,0 x 1,0 100 195 111

L 5,0 x 1,0 150 245 1125,5 x 1,0 125 230 1136,0 x 1,2 100 205 1146,5 x 1,2 150 255 1158,0 x 1,2 175 290 116

10,0 x 1,6 200 325 117

52325


sTypeOutput: DIN 5264 A, ISO 2380. Blade burnished,insulated. Conical cutting edge, with Lasertip (3,5 -10 mm blade width). Routine-tested, standard:IEC 60900: 2004. Soft zone Kraftform handlewith roll stop.


52326


2,5 x 0,4 80 161 1013,0 x 0,5 100 181 1023,5 x 0,6 100 181 1034,0 x 0,8 100 198 104


5,5 x 1,0 125 223 1056,5 x 1,2 150 255 1068,0 x 1,2 175 287 107

10,0 x 1,6 200 312 109

52326


,TypeOutput: DIN 5264 A, ISO 2380-1. Routine-tested,DIN EN 60900 (IEC 900), standard DIN 7437. Bladewith matt-chrome finish, full-hardened, tip burnished.Ergonomic 3-component handle, impact-proof.Permanent colour coding on both handle ends (forslotted screws = yellow).


52328 205-207


2,5 x 0,4 75 177 2013,0 x 0,5 100 202 2023,5 x 0,6 100 222 2034,0 x 0,8 100 222 204


5,5 x 1,0 125 247 2056,5 x 1,2 150 272 2068,0 x 1,2 175 297 207

52328

52328 201-204

ß Hand tools


5

Screwdrivers (grub screwdrivers)

,TypeBlade coated to tip, hardened. Tapered, slim handlemade of plastics.

ApplicationFor set screws (grub screws) M 2,3 - M 5.QualityBlade made of vanadium-extra steel.

52371


2,0 x 0,4 63 143 2012,5 x 0,4 75 155 202


3,0 x 0,5 80 165 203

52371

Phillips screwdrivers PH

ßTypeOutput: DIN 5260 PH, ISO 8764 PH. Round blade,hardened, with nicromatt surface, non-dazzle andnon-peeling, Black Point tip and Kraftform handlewith roll stop.

ApplicationFor Phillips recess head screws. QualityBlade made of high-alloyed vanadium steel.

52386

Set contents Size x Blade length 52386 …mm

3-part 1 x 80 / 2 x 100 / 3 x 150 101

52390 208

52386 - 52390

Size Blade length Overall length 52390 …mm mm

0 60 141 2011 80 161 2022 100 198 204


3 150 262 20601 25 79 20802 25 79 209



Quality Blade made of chrome-vanadium steel. 52391


3-part 1 x 80 / 2 x 100 / 3 x 150 101


0 60 146 1011 80 187 1022 100 219 103


3 150 269 1044 200 319 105

52391 - 52392


+TypeOutput: DIN 5260 PH, ISO 8764 PH. Round blade,glossy nickel-plated, full-hardened, with impact-pro-of, red square end handle made of cellulose acetate.

ApplicationFor Phillips recess head screws.QualityBlade made of chrome-vanadium-molybdenumsteel.

52395


3-part 1 x 80 / 2 x 100 / 3 x 150 101


0 60 135 1011 80 175 102


2 100 205 1033 150 265 104

52396

52395 - 52396

eng/OP

• Phillips screwdrivers PH

www.hhw.de52.10

5


sAusführungOutput: DIN 5260 PH, ISO 8764 PH.Round blade, nicromatt, with Lasertip (size 1 - 3)and soft zone Kraftform® handle with roll stop.ApplicationFor Phillips recess head screws.


Note:Blade length 25 and 300 mm handle made of one-component material w/o. soft zones.

52405 110-111

52405

52400 - 52405


+TypeOutput: DIN 5260 PH, ISO 8764 PH. Round blade,full-hardened, matt-chrome finish. ChromTop tip.SoftFinish® handle with roll stop.

ApplicationFor Phillips recess head screws.QualityBlade made of high-quality chrome-vanadium-molybdenum steel.

52398


0 60 164 2011 80 191 202


2 100 218 2053 150 274 208

52398


,TypeOutput: DIN/ISO 8764-1. Round blade, full-hardened, matt-chrome finish,burnished tip. Ergonomic 3-component handle,impact-proof. Permanent colour coding on bothhandle ends (for PH = red).

Application For Phillips recess head screws.QualityBlade made of vanadium-extra steel.

52419 302-303

Size Blade length Overall length 52419 … 52420 …mm mm

0 60 182 3011 75 197 302

L 1 200 322 3032 100 222 304

L 2 200 322 3053 150 272 306

01 25 83 20102 25 83 202

52419 304-306

52420

52419 - 52420


0 60 141 1011 80 178 102

L 1 200 298 103XL1 300 398 104

2 100 205 105L 2 200 305 106


XL 2 300 398 1073 150 262 1084 200 312 109

01 25 79 11002 25 79 111


3-part 1 x 80 / 2 x 100 / 3 x 150 101

52419 301


+TypeOutput: DIN 5260 PH, ISO 8764 PH.Round blade, fully glossy nickel-plated, full-harde-ned, with hexagonal shoulder on tang for using awrench and handle made of hardwood. Impact headwith leather cap, therefore no damage to end of

handle.ApplicationFor Phillips recess head screws.QualityBlade made of chrome-vanadium steel.

52421


1 80 180 1012 100 205 102


3 150 270 1034 200 330 104

52421

ß Hand tools


5


ßTypeOutput: DIN 5260 PH, ISO 8764 PH. Full-length hexagonal blade with impact cap,hardened, with nicromatt surface, dazzle-free andnon-peeling, Black-Point tip, tempered hexagonalshoulder on tang for using a wrench and Kraftform

handle with roll stop.ApplicationFor Phillips recess head screws.QualityBlade made of high-alloyed special vanadiumsteel.

52427


3-part 1 x 80 / 2 x 100 / 3 x 150 101


1 80 161 1012 100 198 102


3 150 262 103

52427 - 52434


0Type Output: DIN 5260 PH, ISO 8764 PH. Hexagonal blade with hexagonal shoulder on tangfor using a wrench, full-hardened, matt-chrome

finish, blackened tip. Multi-component handle with extra large softzone and attachment eye. Quality Blade made of chrome-vanadium-molybdenumsteel.

52437


1 80 180 1012 100 212 102


3 150 262 103

52437


+Type Output: DIN 5260 PH, ISO 8764 PH.Hexagonal blade with hexagonal shoulder on tangfor using a wrench, full-hardened, matt-chromefinish. ChromTop tip. SoftFinish® handle with roll

stop.Application For Phillips recess head screws. Quality Blade made of high-quality chrome-vanadium-molybdenum steel.

52438


1 80 186 1012 100 213 102


3 150 268 103

52438

Set of Phillips screwdrivers PH

+TypeOutput: DIN 5260 PH, ISO 8764 PH. Hexagonal blade with hexagonal shoulder on tangfor using a wrench, full-hardened, matt-chromefinish. ChromTop tip. SoftFinish® handle with rollstop and steel plate.

ApplicationFor Phillips recess head screws.QualityBlade made of high-quality chrome-vanadium-molybdenum steel.

52439


3-part 1 x 80 / 2 x 100 / 3 x 150 201

52439

Phillips screwdriver PH/The chisel-screwdriver

sTypeOutput: DIN 5260 PH, ISO 8764 PH.Full-length hexagonal blade, impact cap andhexagonal shoulder on tang for using a wrench. BlackPoint tip, exceptionally tough tempered. Soft zone

Kraftform® handle with roll stop.ApplicationFor Phillips recess head screws.QualityBlade made of 73 Mo V 5 2.

52443


1 80 178 1022 100 205 103


3 150 262 1044 200 317 105

52443

eng/OP

• Phillips screwdrivers PH • ESD/EGB screwdrivers PH • Electrician’s screwdrivers PH

www.hhw.de52.12

5


sTypeOutput: DIN 5260 PH, ISO 8764 PH.With Lasertip (size 1 - 3), hexagonal blade,nicromatt, hexagonal shoulder on tang for using a

wrench (size 1 - 3 and soft zone Kraftform®

handle with roll stop.ApplicationFor Phillips recess head screws.QualityBlade made of 73 Mo V 5 2.

52444


0 60 141 1011 80 178 102


2 100 205 1033 150 262 104

52444

ESD/EGB Phillips screwdrivers PH

sTypeOutput: DIN 5260 PH, ISO 8764 PH. Round blade,Black-Point tip, Kraftform® handle with roll stop.

ApplicationFor Phillips recess head screws. For application withelectronic construction parts with risk of electrosta-tics. Fulfils the standard EN 100-015 part 1.QualityBlade made of high-alloyed special steel.


0 60 157 1011 80 177 102


2 100 198 104

52445 104

52445

VDE electrician’s screwdrivers PH

ßTypeOutput: DIN 5260 PH, ISO 8764 PH. Routine-te-sted in compliance with VDE 0680/T201, IEC 900,norm DIN 7438, Black-Point tip and Kraftform

handle.ApplicationFor Phillips recess head screws.QualityBlade burnished, insulated.

52446


3-part 1 x 80 / 2 x 100 / 3 x 150 101


0 80 165 1011 80 170 102


2 100 200 1033 150 260 104

52446 - 52448

52445 101-102


0Type Output: DIN 5260 PH, ISO 8764 PH. Routine-te-

sted in compliance with DIN EN 60900 (IEC 900),DIN 7438.QualityBlade burnished, insulated.

52451


3-part 1 x 80 / 2 x 100 / 3 x 150 101

52451


0 60 146 2011 80 187 202


2 100 219 2033 150 269 204


1 80 191 1012 100 218 102

VDE electrician’s screwdrivers PH52440

+TypeOutput: DIN 7438, DIN ISO 8764.Routine-tested, IEC 60900:2004.SoftFinish® handle with roll stop. The protectiveinsulation is completely integrated in the front part ofthe blade. 38 mm constant thin diameter: this

ensures that screws or springs can be reached evenin hard-to-reach places.ApplicationFor Phillips recess head screws.QualityBlade made of chrome-vanadium-molybdenumsteel, full-hardened, burnished.

52440

ß Hand tools


5

52453 201

52453 205


+TypeOutput: DIN 7438, ISO 8764 PH. Routine-tested, DIN EN 60900 (IEC 900). SoftFi-nish® handle with roll stop.

ApplicationFor Phillips recess head screws.QualityBlade made of chrome-vanadium-molybdenumsteel, full-hardened, burnished.

52449


3-part 1 x 80 / 2 x 100 / 3 x 150 101


0 60 164 1001 80 191 101


2 100 218 1023 150 274 103

52449 - 52450


sTypeOutput: DIN 5260 PH, ISO 8764 PH.Blade burnished, insulated. With Lasertip (size 1 -3). Routine-tested, standard: IEC 60900:2004.Ergonomically optimised soft zone Kraftform®

handle with roll stop.

ApplicationFor Phillips recess head screws.QualityBlade made of 73 Mo V 5 2.

52452


0 60 161 1011 80 178 1022 100 205 103


3 150 262 1044 200 312 105

52452


,TypeOutput: DIN/ISO 8764-1. Routine-tested, DIN EN 60900 (IEC 900), standardDIN 7438. Blade with matt-chrome finish, full-harde-ned, tip burnished. Ergonomic 3-component handle,impact-proof. Permanent colour coding on bothhandle ends (for PH = red).

ApplicationFor Phillips recess head screws.QualityBlade made of vanadium-extra steel.

52453 202-204


0 75 162 2011 80 202 2022 100 222 203


3 150 272 2044 200 361 205

52453

VDE electrician’s screwdriver for PH/slotted screws

sTypeOutput: For both Phillips and slotted screws.Blade insulated. Routine-tested, standard: IEC60900:2004. Ergonomically optimised soft zoneKraftform® handle with roll stop.

ApplicationFor PlusMinus screws Phillips/slotted screws.QualityBlade made of 73 Mo V 5 2.

52436


1 80 178 1012 100 205 102

52436

eng/OP

• Phillips screwdrivers PH

www.hhw.de52.14

5

Pozidriv screwdrivers PZ

ßTypeOutput: DIN 5260 PZ, ISO 8764 PZ. Round blade, hardened, with nicromatt surface,non-dazzle and non-peeling, Black Point tip andblack Kraftform handle with roll stop.

ApplicationFor Pozidriv/Supadriv cross head screws.QualityBlade made of high-alloyed special vanadiumsteel.

52455


3-part 1 x 80 / 2 x 100 / 3 x 150 101

Size Blade length Overall length 52458 …mm länge mm

1 80 161 1022 100 198 103

Size Blade length Overall length 52458 …mm länge mm

3 150 262 104

52455 - 52458



Quality Blade made of chrome-vanadium steel. 52481


3-part 1 x 80 / 2 x 100 / 3 x 150 101


0 60 146 1011 80 187 102


2 100 219 1033 150 269 104

52481 - 52482


+TypeOutput: DIN 5260 PZ, ISO 8764 PZ. Round blade, full-hardened, matt-chrome finish.ChromTop tip. SoftFinish® handle with roll stop.

ApplicationFor Pozidriv/Supadriv cross head screws.QualityBlade made of high-quality chrome-vanadium-molybdenum steel.

52459


0 60 164 2011 80 191 202


2 100 218 2033 150 274 204

52459


sTypeOutput: DIN 5260 PZ, ISO 8764 PZ.Round blade, nicromatt, with Lasertip (size 1 - 3)and soft zone Kraftform® handle with roll stop.ApplicationFor Pozidriv screws.QualityBlade made of 73 Mo V 5 2.

Note:Blade length 25 mm handle made of one-compo-nent material w/o. soft zones.

52460

52460 204-205


0 60 141 2001 80 178 201

L 1 200 298 208XL 1 300 398 206

2 100 205 202


L 2 200 305 209XL 2 300 405 207

3 150 262 20301 25 79 20402 25 79 205

52460

ß Hand tools


5


+Type Output: DIN 5260 PZ, ISO 8764 PZ. Round blade, fully glossy nickel-plated, full-harde-ned, with hexagonal shoulder on tang for using awrench and handle made of hardwood. Impact headwith leather cap, therefore no damage to end ofhandle.

Application For Pozidriv/Supadriv cross head screws. Quality Blade made of chrome-vanadium steel.

52480


1 80 180 2012 100 205 202


3 150 270 203

52480


0Type Output: DIN 5260 PZ, ISO 8764 PZ. Hexagonal blade with hexagonal shoulder on tangfor using a wrench, full-hardened, matt-chromefinish, blackened tip. Multi-component handle withextra large soft zone and attachment eye.

Quality Blade made of chrome-vanadium-molybdenumsteel.

52454


1 80 180 1012 100 212 102


3 150 262 103

52454

Phillips screwdriver PZ/The chisel-screwdriver

sTypeOutput: DIN 5260 PZ, ISO 8764 PZ.Full-length hexagonal blade with impact plate andhexagonal shoulder on tang for using a wrench.Black Point tip, exceptionally tough tempered. Softzone Kraftform® handle with roll stop.

ApplicationFor Pozidriv cross head screws.QualityBlade made of 73 Mo V 5 2.

52461


1 80 178 2022 100 205 203


3 150 262 2044 200 317 205

52461


sTypeOutput: DIN 5260 PZ, ISO 8764 PZ. With Lasertip(size 1 - 3), hexagonal blade, nicromatt, hexagonalshoulder on tang for using a wrench (size 1 - 3) andsoft zone Kraftform® handle with roll stop.


52462


0 60 141 1001 80 178 101


2 100 205 1023 150 262 103

52462

eng/OP

• Electrician’s screwdrivers PZ • Sets of screwdrivers

www.hhw.de52.16

5

VDE electrician’s screwdrivers PZ

ßTypeOutput: DIN 5260 PZ, ISO 8764 PZ. Routine-te-sted in compliance with VDE 0680/T 201, IEC900, Black-Point tip and Kraftform handle.

ApplicationFor Pozidriv/Supadriv cross head screws.QualityBlade burnished, insulated.

52466


3-part 1 x 80 / 2 x 100 / 3 x 150 101


0 80 165 1011 80 170 102


2 100 200 1033 150 260 104

52466 - 52467


0Type Output: DIN 5260 PZ, ISO 8764 PZ. Routine-tested in compliance with DIN EN 60900(IEC 900), DIN 7438.



3-part 1 x 80 / 2 x 100 / 3 x 150 101


0 60 146 1011 80 187 102


2 100 219 1033 150 269 104

52478 - 52479


3-part 1 x 80 / 2 x 100 / 3 x 150 101


0 60 164 2011 80 191 202


2 100 218 2033 150 324 204


+Type Output: DIN 7438, ISO 8764 PZ. Routine-tested, DIN EN 60900 (IEC 900). SoftFi-nish® handle with roll stop.Application For Pozidriv/Supadriv cross head screws.

Quality Blade made of chrome-vanadium-molybdenumsteel, full-hardened, burnished.

52465

52465


1 80 191 1012 100 218 102

VDE electrician’s screwdrivers PZ52495

+TypeOutput: DIN 7438, DIN ISO 8764.Routine-tested, IEC 60900:2004.SoftFinish® handle with roll stop. The protectiveinsulation is completely integrated in the front part ofthe blade. 38 mm constant thin diameter: thisensures that screws or springs can be reached evenin hard-to-reach places.

ApplicationFor Pozidriv/Supadriv cross head screws.QualityBlade made of chrome-vanadium-molybdenumsteel, full-hardened, burnished.

52495

ß Hand tools


5


sTypeOutput: DIN 5260 PZ, ISO 8764 PZ.Blade burnished, insulated. With Lasertip (size 1 -3). Routine-tested, standard: IEC 60900: 2004.Soft zone Kraftform handle with roll stop.


52468


0 60 161 2011 80 178 2022 100 205 203


3 150 262 2044 200 312 205

52468

VDE electrician’s screwdriver for PZ/slotted screws

sTypeOutput: For both Pozidriv and slotted screws.Blade insulated. Routine-tested, standard: IEC60900:2004. Ergonomically optimised soft zoneKraftform® handle with roll stop.

ApplicationFor PlusMinus screws Pozidriv/slotted screws.QualityBlade made of 73 Mo V 5 2.

52491


1 80 178 1012 100 205 102

52491

Sets of screwdrivers, assorted

ßTypeOutput: Q DIN 5264 A, ISO 2380,D DIN 5260 PH, ISO 8740 PH,E DIN 5260 PZ, ISO 8740 PZ.Blade hardened throughout, with nicromatt surface,non-dazzle and non-peeling, Black Point tip andKraftform handle with roll stop.QualityBlade made of high-alloyed special vanadiumsteel.

52469 201-203Type6-part, round blade.

52469 204Type6-part, full-length hexagonal blade with impact plate,hardened, tempered hexagonal shoulder on tang forusing a wrench.

52469 202

52469 201

52469 203

52469 204

52469

Contents 1 ea. 52469 …

Q 4 x 100 mm / 5 x 100 mm / 7 x 150 mm / voltage tester 3 x 146 mm, 150-250 Volt 201D PH 1/80 / PH 2/100Q 3 x 80 mm / 4 x 100 mm / 5 x 100 mm / 7 x 150 mm, 202E PZ 1/80 / PZ 2/100Q 3 x 80 mm / 4 x 100 mm / 5 x 100 mm / 7 x 150 mm, 203D PH 1/80 / PH 2/100Q 3,5 x 75 mm / 4,5 x 90 mm / 5,5 x 100 mm / 7 x 125 mm, 204D PH 1/80 / PH 2/100

Performance requires quality.www.atorn.com

Screwdrivers by ATORN:

ATORN‘s high-quality hand tools.

eng/OP

• Sets of screwdrivers

www.hhw.de52.18

5


0Type Output: Q DIN 5264 A, ISO 2380. D DIN 5260 PH, ISO 8740 PH. E DIN 5260 PZ, ISO 8740 PZ. Blade full-hardened. Multi-component handle withextra large soft zone and attachment eye. Incardboard box.Quality Blade made of chrome-vanadium steel.

52472 099-100 Type Round blade, glossy nickel-plated.

52472 101-102 Type Hexagonal blade with hexagonal shoulder on tangfor using a wrench, with matt-chrome finish,blackened tip.

52472 099


Q 4,0 x 100 / 5,5 x 125 / 6,5 x 150 / 8 x 175, 099D PH 1/80 / PH 2/100Q 4,0 x 100 / 5,5 x 125 / 6,5 x 150 / 8 x 175, 100E PZ 1/80 / PZ 2/100Q 4,5 x 90 mm / 5,5 x 100 mm / 6,5 x 125 mm / 8 x 150 mm, 101D PH 1/80 / PH 2/100Q 5,5 x 100 mm / 6,5 x 125 mm / 8 x 150 mm, 102D PH 1/80 / PH 2/100 / PH 3/150,E PZ 1/80 / PZ 2/100

52472 100

52472 101

52472 102

52472


sType6-part, round blade, nicromatt, with Lasertip andKraftform handle with roll stop, multi-component.With rack.QualityBlade made of 73 Mo V 5 2.

52492 101Output:Q DIN 5264 A, ISO 2380,D DIN 5260 PH, ISO 8764 PH.

52492 102Output:Q DIN 5264 A, ISO 2380,D DIN 5260 PH, ISO 8764 PH,E ISO 8764 PZ.

51492 101 52492 102


Q 3,0 x 80 mm / 4,0 x 100 mm / 5,5 x 125 mm / 6,5 x 150 mm, 101D PH 1/80 / PH 2/100Q 4,0 x 100 mm / 5,5 x 125 mm, 102D PH 1/80 / PH 2/100,E PZ 1/80 / PZ 2/100

52492


sType6-part, full-length hexagonal blade and hexagonalshoulder on tang for using a wrench. Soft zoneKraftform® handle with roll stop. With rack.QualityBlade made of 73 Mo V 5 2.

52470TypeOutput:Q DIN 5264 A, ISO 2380,D DIN 5260 PH, ISO 8740 PH.The chisel-screwdriver. With impact cap andBlack-Point tip, exceptionally tough tempered.

52471TypeOutput:Q DIN 5264 A, ISO 2380,E DIN 5260 PZ, ISO 8740 PZ.Kraftform. With Lasertip, nicromatt.

52470 101 52470 102

52471 201 52471 202

Contents 1 ea. 52470 … 52471 …

Q 3,5 x 75 mm / 4,5 x 90 mm / 5,5 x 100 mm / 7 x 125 mm, 101 201D PH 1/80 / PH 2/100Q 3,5 x 75 mm / 4,5 x 90 mm / 5,5 x 100 mm / 7 x 125 mm, 102 202E PZ 1/80 / PZ 2/100

52470 - 52471

ß Hand tools


5

Sets of stainless steel screwdrivers, assorted

sType6-part, round blade, stainless steel, with Lasertipand Kraftform handle with roll stop, multi-compo-nent. With rack.QualityBlade made of stainless steel.

52493 101TypeOutput:Q DIN 5264 A, ISO 2380,D DIN 5260 PH, ISO 8764 PH.

52493 102TypeOutput:Q DIN 5264 A, ISO 2380,E ISO 8764 PZ.

52493 103TypeOutput:Q DIN 5264 A, ISO 2380,D DIN 5260 PH, ISO 8764 PH.E ISO 8764 PZ.

52493 101

52493 102 52493 103


Q 3,0 x 80 mm / 4,0 x 100 mm / 5,5 x 125 mm / 6,5 x 150 mm, 101D PH 1/80 / PH 2/100Q 3,0 x 80 mm / 4,0 x 100 mm / 5,5 x 125 mm / 6,5 x 150 mm, 102E PZ 1/80 / PZ 2/100Q 3,0 x 80 mm / 6,5 x 150 mm, 103D PH 1/80 / PH 2/100,E PZ 1/80 / PZ 2/100

52493

Set of screwdrivers, assorted

+Type Output: Q DIN 5264 A, ISO 2380, D DIN 5260 PH, ISO 8740 PH. 6-part, round blade, glossy nickel-plated, full-har-dened, with handle made of hardwood, naturalbeechwood, lacquered. Impact head with leathercap, therefore no damage to end of handle.


Note: Starting at 5,5 mm blade width full-length blade,hexagonal shoulder on tang for using a wrench andcorrugated tip against slipping.

52476


3,5 x 75 mm / 4,5 x 90 mm / 5,5 x 100 mm / 7,0 x 125 mm, 201D PH 1/80 / PH 2/100

52476


+Type Output: Q DIN 5264 A, ISO 2380, D DIN 5260 PH, ISO 8740 PH, E DIN 5260 PZ, ISO 8740 PZ, Blade full-hardened, matt-chrome finish. ChromToptip. SoftFinish® handle with roll stop.Quality Blade made of high-quality chrome-vanadium-molybdenum steel.

52477 101-103 Type 6-part, round blade.

52477 104 Type 6-part, hexagonal blade with hexagonal shoulder ontang for using a wrench and steel plate.

52477 101


Q 3,5 x 100 mm / 4,5 x 125 mm / 5,5 x 150 mm / 6,5 x 150 mm, 101D PH 1/80 / PH 2/100Q 4,0 x 100 mm / 5,5 x 125 mm / 6,5 x 150 mm, 102D PH 1/80 / PH 2/100, E PZ 2/100D PH 1/80 / PH 2/100 / PH 3/150, 103E PZ 1/80 / PZ 2/100 / PZ 3/150Q 3,5 x 75 mm / 4,5 x 90 mm / 5,5 x 100 mm / 6,5 x 125 mm, 104D PH 1/80 / PH 2/100

52477 102

52477 103 52477 104

52477

eng/OP

• Sets of screwdrivers • Precision Electronic • ESD • VDE

www.hhw.de52.20

5


,Type Output: Q DIN 5264 A, ISO 2380-1 A. D DIN/ISO 8764-1.E DIN/ISO 8764-1. 6-part, round blade, full-hardened, matt-chromefinish, burnished tip. Ergonomic 3-componenthandle, impact-proof. Permanent colour coding onboth handle ends. Quality Blade made of vanadium-extra steel.

52490 101


Q 3 x 60 mm / 4 x 100 mm / 5,5 x 100 mm / 6,5 x 125 mm, 101D PH 1/75 / PH 2/100Q 3 x 60 mm / 4 x 100 mm / 5 x 100 mm / 5 x 125 mm, 102E PZ 1/75 / PZ 2/100Q 3,5 x 75 mm/ 5,5 x 100 mm, 103D PH 1/75 / PH 2/100,E PZ 1/75 / PZ 2/100

52490 102

52490 103

52490

Set of precision electronics screwdrivers

sType6-part, Kraftform Micro with roll stop and rotatablecaps, multi-component. Blade: round, nicromatt,Black-Point. In plastic stand.

63078

Contents 63078 …

For slotted screws 0,3 x 1,8 / 0,4 x 2,0 / 0,4 x 2,5 / 0,5 x 3,0. Phillips PH 00 / PH 0 101For slotted screws 0,4 x 2,5 / 0,5 x 3,0 / 0,6 x 3,5 / 0,8 x 4,0. Phillips PH 0 / PH 1 102TORX® TX 7 / 8 / 9 / 10 / 15 / 20 103Hexagon, solid size 0,9 / 1,3 + ball head size 1,5 / 2 / 2,5 / 3 104Hexagon, hollow size 2 / 2,5 / 3 / 3,5 / 4 / 5 105

63078

Set of EGB screwdrivers

sType6-part, Kraftform Micro with roll stop and rotatablecaps, multi-component. Blade: round, nicromatt,Black-Point. In plastic stand.

Set contents:Screwdriver 0,25 / 0,23 / 0,30 and 0,40.Phillips screwdriver PH 0 and PH 1.

63099

Contents 63099 ...

6-part 101

63099

ScrewdriverBlade thickness Blade width Blade lengthstärke mm mm mm0,25 1,2 400,23 1,5 400,30 1,8 600,40 2,5 80

Phillips screwdriverSize Blade length

mmPH 0 60PH 1 80

ß Hand tools


5

Set of VDE screwdrivers, assorted

ßType6-part, routine-tested in compliance with VDE0680/T 201, IEC 900, Black-Point tip and Kraftformhandle.QualityBlade made of high-alloyed special vanadiumsteel.

52473 101Output:Q DIN 5264 A, ISO 2380,D DIN 5260 PH, ISO 8740 PH.

52473 102Output:Q DIN 5264 A, ISO 2380,E DIN 5260 PZ, ISO 8740 PZ.

52473


Q 2,5 x 80 mm / 3,5 x 100 mm / 4 x 100 mm / 5,5 x 125 mm, 101D PH 1/80 / PH 2/100Q 2,5 x 80 mm / 3,5 x 100 mm / 4 x 100 mm / 5,5 x 125 mm, 102E PZ 1/80 / PZ 2/100

52473


0Type Output: Q DIN 5264 A, ISO 2380. D DIN 5260 PH, ISO 8740 PH. 7-part, Routine-tested in compliance with DINEN 60900 (IEC 900), Norm DIN 7438.



Q 2,5 x 75 / 4 x 100 / 5,5 x 125 / 6,5 x 150, 101Q voltage tester 3 x 140 mm, 150 - 250 Volt,D PH 1/80 / PH 2/100

52483


+TypeOutput: Q DIN 5264 A, ISO 2380. D DIN 5260 PH, ISO 8740 PH.6-part, routine-tested, DIN EN 60900 (IEC 900).SoftFinish® handle with roll stop.


52474


Q 3 x 100 mm / 4 x 100 mm / 5,5 x 125 mm / 6,5 x 150 mm, 101D PH 1/80 / PH 2/100

52474


sTypeOutput: Q DIN 5264 A, ISO 2380,D DIN 5260 PH, ISO 8740 PH.7-part, routine-tested, standard: IEC 60900:2004.Blade burnished, insulated. With Lasertip (2,5 x 80mm without). Soft zone Kraftform® handle with rollstop. With rack.



Q 2,5 x 80 mm / 3,5 x 100 mm / 4 x 100 mm / 5,5 x 125 mm, 201D PH 1/80 / PH 2/100Q voltage tester 3,0 x 70 mm

52475

eng/OP

• Set of VDE screwdrivers

www.hhw.de52.22

5


,TypeRoutine-tested, DIN EN 60900 (IEC 900). Blade,full-hardened, matt-chrome finish, burnished tip.Ergonomic 3-component handle, impact-proof.Permanent colour coding on both handle ends. Quality Blade made of vanadium-extra steel.

52486 201 5-part, output: Q DIN 5264 A, ISO 2380-1 A,D DIN/ISO 8764-1.

52486 203 7-part, output: Q DIN 5264 A, ISO 2380-1 A,E DIN/ISO 8764-1.

52486 201


Q 3 x 100 / 4 x 100 / 5 x 125, 201D PH 1/80 / PH 2/100Q 2,5 x 75 / 3 x 100 / 4 x 100 / 5,5 x 125, 203E PZ 0/60 / PZ 2/100 / PZ 3/150

52486 203

52486

Set of VDE reversible screwdrivers

BType14-part, routine-tested in compliance withDIN/ISO 60900:2004. With 12 IEC exchangeableblades, 2-component handle and turning cap, in

robust sheet steel box. The blades are securely heldinside the handle, automatic lock against unintendedpulling out. Attachable turning cap and soft zone forusage as precision tool.

52488

52488


Q 2,5 x 0,4 / 3,0 x 0,5 / 3,5 x 0,6 / 4,0 x 0,8 / 5,5 x 1,0 / 6,5 x 1,2 mm, 101D PH 1x80 / PH 2x100,E PZ 2x100,M T 10 / T 15 / T 20,

handle 105 x 39 mm, turning cap.

VDE reversible blades

B52489 101-118 Reversible blades TypeRoutine-tested, in compliance with DIN/EN60900:2004. Attachable turning cap and soft zonefor usage as precision tool.

52489 115-116TypeFor both Phillips and slotted screws.ApplicationFor terminals, electrical cabinets, etc.

52489 117-118TypeFor both Pozidriv and slotted screws.ApplicationFor terminals, electrical cabinets, etc.

52489 201HandleTypeThe blades are securely held inside the handle,automatic lock against unintended pulling out.Application For mounting the reversible blades cat.-no. 52489101-118.

52489 101-106

52489 201

52489

Cutting edge width x thickness Size Blade length 52489 …mm mm

Q 2,5 x 0,4 – 75 101Q 3,0 x 0,5 – 100 102Q 3,5 x 0,6 – 100 103Q 4,0 x 0,8 – 100 104Q 5,5 x 1,0 – 100 105Q 6,5 x 1,2 – 100 106D – PH 1 100 107D – PH 2 100 108E – PZ 1 100 109E – PZ 2 100 110M – T 8 100 111M – T 10 100 112M – T 15 100 113M – T 20 100 114: – H 1 80 115: – H 2 100 116; – Z 1 80 117; – Z 2 100 118

Handle – – – 201

ß Hand tools


5


Q 3,0 x 0,5 / 4,0 x 0,8 / 5,5 x 1,0 / 6,5 x 1,2 mm, 101D PH 1x83 / PH 2x83,N hand grip 6 x 160 mm

Cutting edge width x thickness Size Overall length Blade length 52497 …mm mm mm

Q 2,5 x 0,4 - 83 - 101Q 3,0 x 0,5 - 83 - 102Q 4,0 x 0,8 - 83 - 103Q 5,5 x 1,0 - 83 - 104Q 6,5 x 1,2 - 83 - 105D - PH 1 83 - 108D - PH 2 83 - 109; - SL/PZ 1 83 - 111; - SL/PZ 2 83 - 112N - - 160 50 201

VDE exchangeable bits with hand grip52496 - 52497

+52496 101Type7-part set, consists of- 6 exchangeable bits (cat.-no. 52497 102-109) and- 1 hand grip (cat.-no. 52497 201).

52497 101-112Exchangeable bitTypeHigh-quality chrome-vanadium-molybdenumsteel, full-hardened, burnished.- The insulation is sprayed directly onto the bit and is

fully integrated in the front of the blade- Routine-tested, IEC 60900:2004- 38 mm constant thin diameter: this ensures that

screws or springs can be reached even in hard-to-reach places.

- Slim bits allow for working in §§hard-to-reachplaces

- Caution: 6 mm VDE exchangeable bits are only tobe used with hand grip (cat.-no. 52497 201).

52497 201Hand gripType- Blade made of chrome-vanadium steel, full-har-

dened- Blade insulation sprayed directly on the blade.- SoftFinish® electric multi-component handle

with roll stop- Bit mount: ClicFix quick-change toolholder

securely holds bits.- Only for 6 mm VDE exchangeable bits (cat.-no.

52497 101-112)- Caution: Do not use for bits of the shapes C 6,3

and E 6,3

52496

52497 101-105

52497 108-109

52497 111-112

52497 201

52494 101

52494 102

VDE reversible screwdriver set

sTypeRoutine-tested, standard: IEC 60900:2004.Blades burnished, insulated, length 154 mm. Drive 9mm Hexagon with insertion chamfer. VDE holderwith Kraftform handle with roll stop, multi-compo-nent, length 102 mm. In case.

52494 101Type7-part.

52494 102Type18-part. With 4 wrenches for switch cabinets, length89 mm.

52494 …

Handle 102 mm, 101Q 2,5 x 0,4 mm / 3,5 x 0,6 mm / 4,0 x 0,8 mm / 5,5 x 1,0 mm,E PZ 0 / PZ 1.

Handle 102 mm, 102Q voltage tester 3,0 x 0,5 x 70 mm,Q 2,5 x 0,4 mm / 3,5 x 0,6 mm / 4,0 x 0,8 mm / 5,5 x 1,0 mm,D PH 1 / PH 2,: # 1 / # 2,E PZ 1 / PZ 2,; # 1 / # 2,7 6,3 x 89 mm,7 8,1 x 89 mm,6 89 mm,- 89 mm.

52494

eng/OP

• TORX® screwdrivers

www.hhw.de52.24

5

TORX® screwdrivers

ßTypeRound blade, hardened, with nicromatt surface,non-dazzle and non-peeling, Black Point tip andKraftform handle with roll stop. Set in cardboard box.ApplicationFor inner TORX® screws.


Note:TORX® selector see cat.-no. 37930.

52520

Set contents Size 52520 …T

5-part 10 / 15 / 20 / 25 / 30 1017-part 8 / 9 / 10 / 15 / 20 / 25 / 30 102

Size Blade length Overall length 52528 …T mm mm6 60 130 2027 60 130 2038 60 130 2049 60 141 205

10 80 161 20615 80 178 207

Size Blade length Overall length 52528 …T mm mm

20 100 198 20825 100 198 20927 115 213 21030 115 213 21140 130 242 21245 130 242 213

52520 - 52528

TORX® screwdriver with hole

0Type Round blade, full-hardened, matt-chrome finish,blackened tip. Multi-component handle with extralarge soft zone and attachment eye. T6 - T9without hole, T10 - T40 with hole, for application onTORX® screws and TORX® safety screws (with pilotpin).

Application For inner TORX® screws. Quality Blade made of chrome-vanadium steel.

Note: TORX® selector see cat.-no. 37930.

52529


5-part 10 / 15 / 20 / 25 / 30 1017-part 8 / 9 / 10 / 15 / 20 / 25 / 30 102


10 80 170 20515 80 180 206


20 100 200 20725 100 200 20827 115 227 20930 115 227 21040 130 242 211

52529

TORX® screwdrivers

+TypeRound blade, full-hardened, matt-chrome finish.ChromTop tip. SoftFinish® handle with roll stop.ApplicationFor inner TORX® screws.

QualityBlade made of high-quality chrome-vanadium-molybdenum steel.


52530

Size Blade length Overall length 52530 …T mm mm3 60 164 2014 60 164 2025 60 164 2036 60 164 2047 60 164 2058 60 164 2069 60 171 207

10 80 191 208


15 80 191 20920 100 211 21025 100 211 21127 115 233 21230 115 233 21340 130 254 21445 130 254 215


6-part 10 / 15 / 20 / 25 / 30 / 40 100

52530

ß Hand tools


5

TORX® screwdrivers

sTypeRound blade, nicromatt, Black-Point tip and softzone Kraftform handle with roll stop.ApplicationFor inner TORX® screws.



52531

52531

Size Blade length Overall length 52531 …T mm mm5 60 141 1016 60 141 1027 60 141 1038 60 141 1049 60 141 105

10 80 161 10615 80 178 107


20 100 198 10825 100 205 10927 115 220 11030 115 220 11140 130 242 11245 130 242 113

52534 201-205

52534 209

TORX® screwdrivers (MagicSpring)

+TypeRound blade, full-hardened, with matt-chromefinish, ChromTop® tip. With MagicSpring holdingspring, SoftFinish® handle with roll stop.ApplicationFor inner TORX® screws.QualityBlade made of high-quality chrome-vanadium-molybdenum steel.


52532



10 80 191 20515 80 191 20620 100 218 20725 100 218 208

The holding spring is laser-weldedto the tip of the tool in conjunctionwith a covering disc.

The MagicSpring generates aclamping between the tool and theTORX® or TORX PLUS® screw, sothat the screw is held safely.

52532

TORX® screwdriver with hole

,TypeRound blade, full-hardened, matt-chrome finish,burnished tip. With hole, which allows the applicati-on with TORX® screws and with TORX® safetyscrews (with pilot pin). Ergonomic 3-componenthandle, impact-proof. Permanent colour coding onboth handle ends (for TORX® = green).Application For inner TORX® screws.

Quality Blade made of vanadium-extra steel.


52534 206-208

Size Blade length Overall length 52534 …T mm mm7 75 197 2018 75 197 2029 75 197 203

10 75 197 20415 100 222 205


20 100 222 20625 125 247 20727 125 247 20830 150 272 20940 150 311 210

52534 210

52534

eng/OP

• TORX® screwdrivers • Ball head screwdrivers

www.hhw.de52.26

5

TORX® screwdriver with holding device

sRound blade, nicromatt. With holding device. Softzone Kraftform handle with roll stop. With rack.Application Inner TORX® screws in compliance with specificati-on Camcar Textron. TORX® with holding device:The tools are pressed into the drive profile of thescrew manufactured in compliance CAMCARTEXTRON specifications by means of: the drivershoulders (conical in respect to the tool tip), theadditional optimisation of the shoulder area and inconjunction with the perfect insertion depth.

Quality Blade made of 73 Mo V 5 2.


52539 101


6-part 10 / 15 / 20 / 25 / 30 / 40 10152539 199-207

52539

VDE TORX® screwdrivers

+Type Routine-tested, DIN EN 60900 (IEC 900). SoftFi-nish® handle with roll stop.Application For inner TORX® screws.



52533


10 60 164 10615 80 191 10720 80 191 108


25 80 198 10930 100 218 111

52533

VDE TORX® screwdrivers

sTypeRoutine-tested, IEC 60900:2004. Ergonomicallyoptimised soft zone Kraftform® handle with rollstop.ApplicationFor inner TORX® screws.



52535


10 80 161 10115 80 178 10220 80 178 103


25 100 205 10430 100 205 105

52535

Size Blade length Overall length 52539 …T mm mm8 60 141 1999 60 141 200

10 80 161 20115 80 178 20220 100 198 203


25 100 205 20427 115 220 20530 115 220 20640 130 242 207

TORX® screwdriver with ball head

sTypeRound blade, nicromatt, Black-Point tip and softzone Kraftform handle with roll stop.ApplicationFor inner TORX® screws.



52538


15 80 178 10120 100 198 10225 100 205 103


27 115 220 10430 115 220 105

52538

ß Hand tools


5

Ball head screwdrivers

ßTypeHexagonal blade, with nicromatt surface, non-dazz-le and non-peeling, Black Point tip and Kraftformhandle with roll stop. Set in cardboard box.

ApplicationFor application in hard-to-reach places and up to anangle of 25°.QualityBlade made of high-alloyed special vanadiumsteel.

52540

Set contents Size 52540 …mm

5-part 3 / 4 / 5 / 6 / 8 101

Size Blade length Overall length 52545 …mm mm mm

2 100 170 2012,5 100 170 202

3 100 175 2034 100 180 204


5 100 190 2056 125 220 2068 150 255 207

52540 - 52545


0Type Round blade, full-hardened, matt-chrome finish,blackened tip. Multi-component handle with extralarge soft zone and attachment eye.

Application For application in hard-to-reach places and up to anangle of 25°. Quality Blade made of chrome-vanadium steel.

52550

Set contents Size 52550 …mm

5-part 3 / 4 / 5 / 6 / 8 101


2 100 186 1012,5 100 186 102

3 100 186 1034 100 197 104


5 100 197 1056 125 232 1068 150 257 107

10 150 269 108

52550 - 52551


+Type Hexagonal blade, full-hardened, matt-chromefinish. SoftFinish® handle with roll stop.Application For application in hard-to-reach places and up to anangle of 25°.


Note:Size 3 - 8 mm with MagicRing.

52546 201-203

Size Blade length Overall length 52546 …mm mm mm1,5 75 179 201

2 100 204 2022,5 100 204 203

3 100 204 204


4 100 211 2055 100 211 2066 125 243 2078 150 268 208

52546


sTypeHexagonal blade, nicromatt, Black-Point tip andsoft zone Kraftform handle with roll stop.

ApplicationFor application in hard-to-reach places and up to anangle of 25°.QualityBlade made of 73 Mo V 5 2.

52548

Size Blade length Overall length 52548 …mm mm mm1,5 60 130 1002,0 100 170 1012,5 100 181 1023,0 100 181 1034,0 100 198 104

Size Blade length Overall length 52548 …mm mm mm5,0 100 205 1056,0 125 230 1068,0 150 262 107

10,0 150 262 10812,0 150 267 109

52548

52546 204-208

eng/OP

• Screw-holding screwdrivers • Offset screwdriver • Combination blades

www.hhw.de52.28

5

Offset screwdrivers for slotted screws DIN 5200

+TypeFull-hardened, matt-chrome finish, with impact-proofplastic handle, black, free of cadmium. 0° and 90°.

ApplicationFor application in hard-to-reach places.QualityBlade made of chrome-vanadium steel.

52576

Cutting edge width Cutting edge thickness Leg length short Overall length 52576 …mm mm mm mm3,5 0,6 8,5 90 1014,0 0,8 9,0 100 1025,5 1,0 10,5 125 1036,5 1,2 13,5 125 1048,0 1,2 17,0 150 10510,0 1,6 24,0 175 10612,0 2,0 27,0 200 107

52576

Offset screwdrivers for Phillips screws PH DIN 5208

+TypeFull-hardened, matt-chrome finish, with impact-proofplastic handle, black, free of cadmium. Offset onboth ends.

ApplicationFor application in hard-to-reach places.QualityBlade made of chrome-vanadium steel.

52581

Size Leg length short Overall length 52581 …mm mm

1 + 2 14,5 125 1012 + 3 21,0 150 1023 + 4 25,0 200 103

52581

Screw-holding screwdrivers52558

+TypeErgonomically-shaped SoftFinish® multi-componenthandle with roll stop.ApplicationFor screwing even in hard-to-reach places. Adapter

sleeve secures the screw.QualityBlade made of chrome-vanadium steel, full-har-dened, burnished.

52558


2,5 x 0,4 75 186 2013,0 x 0,5 100 211 2024,0 x 0,8 125 243 2035,0 x 1,0 150 268 204

For blade Ø For blade Ø For insulation Ø For insulation Ø 52561 …mm size mm size

4,5 - 6,0 PH/PZ 1+2 - - 101VDE - - 4,5 - 6,0 / 6,5 - 8,0 PH/PZ 1 / PH/PZ 2 102

Screw grippers52561

sType- With freewheeling sleeve for easier guidance of the

screwdriver- Functions without magnetic force.- Virtually wear-proof material- Pull-off force far above EN standard- For workshop and electric applicationsApplication1 - Push screw gripper onto the tip until the blade

protudes from the rubber part.2 - Affix the screw to the blade tip and secure it in

the gripper.3 - Pull the screw gripper further in the direction of

the handle until the gripper's arms encircle thescrew's head and are forced apart slightly.

4 - The Wera screw gripper automatically releasesthe screw after the screwing is finished! Whenthe grippers touch the surface, the are forcedapart further and snap over when the screw headis fully inserted.

5 - The screw gripper automatically moves up inblind holes. Therefore, even hard-to-reach placesare no problem.

52561 101 52561 102

1

5

4

3

2

ß Hand tools


5

Set contents:1 SYSTEM 6 SoftFinish® telescopic handle,

Q Q 2 blades for slotted screws 4,0-6,0 / 5,5-6,5 mm,D D 1 blade for Phillips recess head screws PH 1-2,E E 1 blade for Phillips recess head screws PZ 1-2,M M 3 blades for TORX® screws T 10-15 / 20-25 / 30-40,

3 blades for hexagonal screws size 4-4 / 5-5 / 6-6 mm.

Set contents 52582 …

11-part 202

The SoftFinish® telescopic handle with Click-Stopp ball clamping guarantees secure seat andquick exchange of blades. Adjustable blade lengthfrom 42-114 mm.

Set of Vario screwdrivers

sTypeMaster set, 11-part, in sheet steel box.QualityBlade made of high-alloyed chrome-vanadium-molybdenum steel.

52586


11-part 101

52586

Combination blade set SYSTEM 6

+Type 11-part SYSTEM 6 SoftFinish® telescopic handlefor adjustable blade lengths from 42-114 mm.Double-sided exchangeable blades with colourcode. In rugged metal box.ApplicationEspecially suitable for dry and general applications.

QualityBlades chrome-vanadium-molybdenum steel,full-hardened, matt-chrome finish. Blade tipsWiha ChromTop®.

52582

52582

Vario screwdriver handles

sTypeWith 6 mm hexagonal mount and 10 mm hexagonalshoulder on tang for using a wrench.

52595Kraftform® handle

52596Kraftform Weralit ESD handleApplication For application with electronic construction parts withrisk of electrostatics. Tested to Norm EN 100-015Part 1.

52595

52595 … 52596 …

101 201

52596

52595 - 52596

Combination screwdriver T-handle

sTypeWith 6 mm hexagonal mount.

ApplicationFor higher torque when tightening and loosening ofseized screws..

52597

52597 …

101

52597

Combination blade extensions

TypeBlade: 6 mm hexagon.ApplicationFor combination and adapter blades (cat.-no. 52605and 52612).

QualityChrome-vanadium steel. 52600

Overall length 52600 …mm175 201

52600

Set contents:1 Kraftform handle,Combination blades, length 175 mm:

Q Q 0,6 x 4 - 1,0 x 6 / 0,8 x 5 - 1,2 x 7 mm,N N size 4 - 4 / 5 - 5 / 6 - 6 mm,D D PH 1 - 2,E E PZ 1 - 2,M M T 10 - 15 / T 20 - 25 / T 30 - 40.

eng/OP

• Combination blades • Bit assortments

www.hhw.de52.30

5

Combination blades

TypeBlade: 6 mm, hexagon, full-hardened, nicromatt.Length 175 mm.QualityChrome-vanadium-molybdenum steel.

Shape Size 52605 …

Q Q 4 x 0,6 / 6 x 1,0 110Q Q 5 x 0,8 / 7 x 1,2 111D D PH 1 / PH 2 120E E PZ 1 / PZ 2 130Q D 4 x 0,8 / PH 1 140Q D 6 x 1,0 / PH 2 141Q D 7 x 1,2 / PH 3 142D E PH 1 / PZ 1 150D E PH 2 / PZ 2 151

J U size 2,5 / 2,5 160

Shape Size 52605 …

J U size 3,0 / 3,0 161J U size 4,0 / 4,0 162J U size 5,0 / 5,0 163J U size 6,0 / 6,0 164

M M T 6 / T 8 170M M T 7 / T 9 171M M T 10 / T 15 172M M T 20 / T 25 173M M T 30 / T 40 174

52605

Adapter blades

TypeBlade: 6 mm hexagon.QualityChrome-vanadium steel.

52612 102TypeWith 1/4 inch quick-exchange mechanism andstrong permanent magnet.ApplicationFor 1/4 inch screwdriver bits.

52612 103TypeWith 1/4 inch external square output.ApplicationFor socket wrench bit 1/4 inch inner square.

52612 102

Length 52612 …mm165 102175 103

52612 103

52612

Bit assortments Kraftform Kompakt®

sType In space-saving, light and robust plastic box.

52630 101Application For manual operation in conjunction with theKraftform® handle and for machine operation inconjunction with the multi-purpose adapter.

52630 098

Set contents 52630 098:1 bit holder Kraftform® with quick-exchange mount Rapidaptor®,

M 6 bits for TORX® screws T 5 / 6 / 7 / 8 / 9 / 10, D 2 bits for Phillips recess head screws PH size 0-25 / 2-25 mm, Q 1 bit for slotted screws 0,5 x 3,0 mm.


Kraftform Kompakt 11 10-part 098Kraftform Kompakt 70 Allround 32-part 101

52630 101

52630

Set contents 52630 101:1 bit holder Kraftform® with quick-exchange mount Rapidaptor®,

D 3 ea. bits for Phillips recess head screws PH size 1-25 / 2-25 / 3-25 mm, E 3 ea. bits for Phillips recess head screws PZ size 1-25 / 2-25 / 3-25 mm, / 6 bits for ResisTORX® screws TX 10 / 15 / 20 / 25 / 30 / 40, J 3 bits Hexagonal-Plus for Allen screws size 4 / 5 / 6 mm, Q 3 bits for slotted screws 0,6 x 4,5 / 1,0 x 5,5 / 1,2 x 6,5 mm,

1 multi-purpose adapter with quick-exchange mount Rapidaptor N 1/4 inch / J 1/4 inch.

52605 110-111

52605 120

52605 130

52605 140-142

52605 150-151

52605 160-164

52605 170-174

ß Hand tools


5

Bit assortment Kraftform Kompakt 50

sType 14-part, with bayonet blade. In space-saving, lightand robust plastic box. Application The bayonet blade can be partly pushed into thehandle, therefore quicker manual operation in hard-to-reach places. When you operate the locking sleeve,

the bayonet blade slides out of the handle and thetool can be used with a regular screwdriver.When you operate the locking sleeve once more,the bayonet blade can be removed and used asadapter for machine operation.

52635

Set contents 52635 101:1 bit holder bayonet Kraftform with quick-exchange mount Rapidaptor,

D 2 bits for Phillips recess head screws PH size 1-25 / 2-25 mm, E 2 bits for Phillips recess head screws PZ size 1-25 / 2-25 mm, / 6 bits for ResisTORX® screws TX 10 / 15 / 20 / 25 / 30 / 40, Q 2 bits for slotted screws 0,6 x 4,5 / 1,0 x 5,5 mm,

1 bayonet blade (connecting piece) with quick-exchange mount Rapidaptor N 1/4 inch / J 1/4inch.


Kraftform Kompakt 50 14-part 101

52635

Bit assortment Kraftform Kompakt 91

sType In space-saving, light and robust plastic box.

Application For manual operation in conjunction with theKraftform® one-hand ratchet for clockwise andcounterclockwise operation and for machine operati-on in conjunction with the multi-purpose adapter.

52640 201

Set contents 52640 201:1 bit one-hand ratchet Kraftform 1/4 inch with quick-exchange mount Rapidaptor,

/ 4 bits for ResisTORX® screws TX 15 / 20 / 25 / 30, D 3 bits for Phillips recess head screws PH size 1-25 / 2-25 / 3-25 mm, J 3 bits for Allen screws size 3 / 4 / 5 mm, N 5 socket wrench bits hexagonal size 5,5 / 7 / 8 / 10 / 13 mm,

1 adapter J 1/4 inch / z 1/4 inch, 1 multi-purpose adapter with quick-exchange mount Rapidaptor N 1/4 inch / J 1/4 inch.


Kraftform Kompakt 91 18-part 201

52640

Bit assortments Kraftform Kompakt® 60/62 (Bit length 89 mm)

sType With holder and 89 mm long bits in folding bag forattachment to the belt.

52642 101


/ 5 bits for ResisTORX® screws TX 10 / 15 / 20 / 25 / 30, ? 4 bits Hexagonal-Plus with borehole for Allen screws size 3 / 4 / 5 / 6 mm, D 3 bits for Phillips recess head screws PH size 1-89 / 2-89 / 3-89 mm, E 3 bits for Phillips recess head screws PZ size 1-89 / 2-89 / 3-89 mm, Q 1 bit for slotted screws 1,0 x 5,5 mm.


/ 8 bits for ResisTORX® screws TX 8 / 10 / 15 / 20 / 25 / 27 / 30 / 40, ? 6 bits Hexagonal-Plus with borehole for Allen screws size 2 / 2,5 / 3 / 4 / 5 / 6 mm,D 3 bits for Phillips recess head screws PH size 1-89 / 2-89 / 3-89 mm, E 3 bits for Phillips recess head screws PZ size 1-89 / 2-89 / 3-89 mm, Q 1 bit for slotted screws 1,2 x 6,5 mm. $ 4 bits for Spanner screws 1 / 2 / 3 / 4, % 3 bits for TORQ-SET® screws 6 / 8 / 10 mm, & 4 bits for TRI-WING® screws 1 / 2 / 3 / 4.


Kraftform Kompakt 60 17-part 101Kraftform Kompakt 62 33-part 103

52642 103

52642

eng/OP

• Bit assortments

www.hhw.de52.32

5

Special assortments

s52643 101Metal twist drill bits and bit setType19-part 1 multi-purpose adapter Rapidaptor, notmagnetic, for mounting in the power screwdriver orin the drill chuck of the electrical drill. Metal twistdrill bits and bits with 1/4 inch drive in compliancewith DIN 3126 C 6,3. In bag.

52643 102Countersinks bit setType8-part 1 holder Kraftform with quick-exchangemount, 1 multi-purpose adapter Rapidaptor, non-magnetic, for mounting in the power screwdriver orin the drill chuck of the electrical drill. Countersinkbits: 3 flutes, countersink angle 90°, countersinkhead in compliance with DIN 335 C, with 1/4 inchdrive in compliance with DIN 326 C 6,3.

52643 103

Combination taps bit setType7-part 1 multi-purpose adapter Rapidaptor, notmagnetic, for mounting in the power screwdriver orin the drill chuck of the electrical drill. Combinationtap bits: tolerance zone ISO 2 (6H), with 1/4 inchdrive in compliance with DIN 326 C 6,3.ApplicationFor drilling core holes (1), tapping (2) and deburring(3) in one operation.

52643 101

Set contents 52643 101:1 multi-purpose adapter Rapidaptor N 1/4 inch / J 1/4 inch,

* 6 metal twist drill bits 3,0 x 38 / 4,0 x 44 / 4,2 x 45 / 5,0 x 50 / 6,0 x 50 / 8,0 x 51 mm,D 6 bits for Phillips recess head screws PH 2 x size 1-25 / 3 x size 2-25 / 1 x size 3-25, M 6 bits for TORX® screws screws T 10 / 15 / 20 / 25 / 30 / 40.

Set contents 52643 102:1 bit holder Kraftform with quick-exchange mount,1 multi-purpose adapter Rapidaptor N 1/4 inch / J 1/4 inch,

+ 6 countersink bits 6,3 x 31 / 8,3 x 31 / 10,4 x 34 / 12,4 x 35 / 16,5 x 40 / 20,5 x 41 mm,


Metal twist drill bits and bit set 19-part 101Countersink bit set 8-part 102Combination taps bit set 7-part 103

52643 102

52643 103

(1)

(2)

(3)

52643

Set contents 52643 103:1 multi-purpose adapter Rapidaptor N 1/4 inch / J 1/4 inch,

* 6 combination taps M3 x 36 / M4 x 39 / M5 x 41 / M6 x 41 / M8 x 51 / M10 x 59.

Set contents:1 bit ratchet 1/4 inch hexagonal drive with 8 mm ring wrench (patented)

N 5 socket wrench bits size 6 / 7 / 8 / 10 / 13 mm,3 bits for slotted screws 4 / 5 / 6 mm,

D 3 bits for Phillips recess head screws PH 1 / 2 / 3,E 3 bits for Phillips recess head screws PZ 1 / 2 / 3,J 4 bits for Allen screws size 3 / 4 / 5 / 6 mm,M 5 bits for TORX® screws T 10 / 15 / 20 / 25 / 30,

1 adapter 1/4 inch square drive x 1/4 inch outside hexagon,1 Quick-Release adapter.


26-part 101

Bit socket wrench assortment with bit ratchet52922

,Type26-part, in plastic box. By means of the patented bitratchet (US Pat. 6860175), screws and nuts caneasily be tightened and loosened even in hard-to-re-ach places.

52922

ß Hand tools


5

Contents 52712 …

17-part 10117-part 10232-part 10332-part 10461-part 105

Set contents 52712 101:1 quick-change toolholder 1/4 inch,

D 4 bits for Phillips recess head screws 1xPH1 / 2xPH2 / 1xPH3,E 4 bits for Phillips recess head screws 1xPZ1 / 2xPZ2 / 1xPZ3,M 8 bits for TORX® screws 1xT10 / 1xT15 / 2xT20 / 2xT25 / 1xT30 / 1xT40.

Set contents 52712 102:1 quick-change toolholder 1/4 inch,

Q 2 bits for slotted screws 4,5 / 6,5 mm,D 3 bits for Phillips recess head screws PH 1 / 2 / 3,E 3 bits for Phillips recess head screws PZ 1 / 2 / 3,J 3 bits for Allen screws size 3 / 4 / 5 mm,M 5 bits for TORX® screws T 10 / 15 / 20 / 25 / 30.

Set contents 52712 103:1 handle with 1/4 inch mount,1 bit holder,

D 9 bits for Phillips recess head screws 2xPH1 / 5xPH2 / 2xPH3,E 9 bits for Phillips recess head screws 2xPZ1 / 5xPZ2 / 2xPZ3,M 12 bits for TORX® screws 2xT10 / 2xT15 / 2xT20 / 2xT25 / 2xT30 / 2xT40.

Set contents 52712 104:1 handle with 1/4 inch mount,1 bit holder,3 bits for slotted screws 4,5 / 5,5 / 6,5 mm,

D 9 bits for Phillips recess head screws 2xPH1 / 5xPH2 / 2xPH3,E 9 bits for Phillips recess head screws 2xPZ1 / 5xPZ2 / 2xPZ3,J 3 bits for Allen screws size 4 / 5 / 6 mm,M 6 bits for TORX® screws T 10 / 15 / 20 / 25 / 30 / 40.

Set contents 52712 105:1 bit holder,

Q 4 bits for slotted screws 4,5 / 5,5 / 6,5 / 8,0 mm,D 18 bits for Phillips recess head screws 4xPH1 / 10xPH2 / 4xPH3,E 18 bits for Phillips recess head screws 4xPZ1 / 10xPZ2 / 4xPZ3,J 8 bits for Allen screws size 2x3 / 2x4 / 2x5 / 2x6 mm,M 12 bits for TORX® screws 2xT10 / 2xT15 / 2xT20 / 2xT25 / 2xT30 / 2xT40.

Bit assortments52712

052712 101-102TypeIncl. of quick-change toolholder 1/4 inch for bits withdrive C 6,3.

52712 103-104TypeIncl. of bit holder with special, free from floatclamping for bits with drive C 6,3 and E 6,3 and 2-component handle with 1/4 inch mount for bit holder.

52712 105Typeincl. of bit holder with special, free from floatclamping for bits with drive C 6,3 and E 6,3.

52712 102

52712 104

52712 105

eng/OP

• Bit assortments

www.hhw.de52.34

5

Bits XLSelectoren

+TypeHigh-quality, impact-proof plastic box.

ApplicationEasy bit removal thanks to integrated clampingledge.

52722 101

Set contents 52722 103:1 ClixFix quick-change toolholder magnetic N 1/4 inch x J 1/4 inch,

Q 3 bits for slotted screws 5,5 / 6,5 / 8,0 mm, torsion zone,D 9 bits for Phillips recess head screws 2xPH1 / 5xPH2 / 2xPH3, torsion zone,E 9 bits for Phillips recess head screws 2xPZ1 / 5xPZ2 / 2xPZ3, torsion zone,J 3 bits for Allen screws size 4,0 / 5,0 / 6,0 mm,M 6 bits for TORX® screws T 10 / 15 / 20 / 25 / 30 / 40.

Set contents 52722 104:1 ClixFix quick-change toolholder magnetic N 1/4 inch x J 1/4 inch,

$ 4 bits for Spanner screws # 4 / 6 / 8 / 10,? 6 bits for Allen screws, with borehole size 2 / 2,5 / 3 / 4 / 5 / 6 mm,% 3 bits for TORQ®-Set screws # 6 / 8 / 10,P 3 bits for Square Drive screws # 1 / 2 / 3,/ 9 bits for ResisTORX® screws TX 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40,& 5 bits for TRI-WING® screws # 0 / 1 / 2 / 3 / 4.

Contents 52722 …

31-part 10131-part 10331-part 104

52722 103

52722 104

52722

INKRA Bits XSelector

+TypePerfect torque transmission and reduced cam-outeffect. Even when working in a slanted position ofthe power tool or the screwdriver, virtually constantinsertion into the screw head.

Application The XSelector (78 x 53 x 15 mm) fits in everypocket. Easy bit removal thanks to integratedclamping ledge.

52729

Set contents 52729 101:1 multi-purpose adapter magneticmagnetic N 1/4 inch / J 1/4 inch, 5 bits for Phillips recess head screws PH 1 / 2 / 2 / 2 / 3, 5 bits for Phillips recess head screws PZ 1 / 2 / 2 / 2 / 3.

Contents 52729 …

11-part 101

Even when working in a slanted position, handling ismuch easier thanks to lower contact pressure.

Slippage and wear of the tip or the screw head arereduced.

52729

Set contents 52722 101:1 multi-purpose adapter magnetic N 1/4 inch x J 1/4 inch,

Q 3 bits for slotted screws 4,5 / 5,5 / 6,5 mm,D 7 bits for Phillips recess head screws 2xPH1 / 4xPH2 / 1xPH3,E 8 bits for Phillips recess head screws 2xPZ1 / 5xPZ2 / 1xPZ3,M 12 bits for TORX® screws 2xT10 / 2xT15 / 2xT20 / 3xT25 / 2xT30 / 1xT40.




ß Hand tools


5

DURA Bits XSelectors

+Type With torsion zone and revolutionary coating. Thestrength-hard, elastic DURA bit with an extremelywear-resistant, patented carbide coating clings tothe screw head with finest micro carbide particles.98,2 % of the users polled during a Wiha-study saythat the Wiha DURA-bit ist -better- or -much better-when compared to bits used so far. Less slip-off

and less pressure needed. Absorbing energy, thebit is protected against early damage. Particularlysuitable for serial screw fittings and for heavy-dutyapplications. Application The XSelector (78 x 53 x 15 mm) fits in everypocket. Easy bit removal thanks to integratedclamping ledge.

52723

Set contents 52723 101:1 ClicFix quick-change toolholder magnetic N 1/4 inch x J 1/4 inch,

Q 2 bits for slotted screws 5,5 / 6,5 mm, D 4 bits for Phillips recess head screws PH 1 / 2 / 2 / 3, E 4 bits for Phillips recess head screws PZ 1 / 2 / 2 / 3.

Contents 52723 …

11-part 101

52723

Standard Bit XSelectors

+Application The XSelector (78 x 53 x 15 mm) fits in everypocket. Easy bit removal thanks to integratedclamping ledge.

52724 101


Q 2 bits for slotted screws 5,5 / 6,5 mm, D 4 bits for Phillips recess head screws PH 1 / 2 / 2 / 3, E 4 bits for Phillips recess head screws PZ 1 / 2 / 2 / 3.


M 10 bits for TORX® screws T 7 / 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40.

Contents 52724 …

11-part 10111-part 10211-part 10411-part 106

52724 102

52724 104

52724 106

52724


D 3 bits for Phillips recess head screws PH 1 / 2 / 3, E 3 bits for Phillips recess head screws PZ 1 / 2 / 3, M 4 bits for TORX® screws T 15 / 20 / 25 / 30.


D 5 bits for Phillips recess head screws PH 1 / 2 / 2 / 3 / 3, M 5 bits for TORX® screws T 15 / 20 / 25 / 30 / 40.

eng/OP

• Bit assortments • Inkra Bits

www.hhw.de52.36

5

Set contents 52720 206:1 multi-purpose adapter with quick-exchange mount N 1/4 inch / J 1/4 inch,

Q 3 bits for slotted screws 0,8 x 5,5 / 1,0 x 5,5 / 1,2 x 6,5 mm, D 3 bits for Phillips recess head screws PH 1 / 2 / 3, E 3 bits for Phillips recess head screws PZ 1 / 2 / 3.


M 9 bits for TORX® screws TX 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40.


/ 6 bits ResisTORX® with borehole T 10 / 15 / 20 / 25 / 30 / 40.

Set contents 52720 208:1 multi-purpose adapter Rapidaptor with quick-exchange mount N 1/4 inch / J 1/4 inch,

Q 1 bit for slotted screws 1,0 x 5,5 mm, D 6 bits for Phillips recess head screws PH 2 x size 1 / 3 x size 2 / 1 x size 3, E 6 bits for Phillips recess head screws PZ 2 x size 1 / 3 x size 2 / 1 x size 3, J 5 bits Hexagonal-Plus for Allen screws size 3 / 4 / 5 / 6 / 8 mm, M 6 bits for TORX® screws TX 10 / 15 / 20 / 25 / 30 / 40, / 5 bits ResisTORX® with borehole T 10 / 15 / 20 / 25 / 30.

Set contents 52720 201:1 BiTorsion holder Rapidaptor with quick-exchange mount N 1/4 inch / J 1/4 inch,

Q 3 bits for slotted screws 0,8 x 5,5 / 1,0 x 5,5 / 1,2 x 6,5 mm,D 3 bits for Phillips recess head screws PH 1 / 2 / 3,E 3 bits for Phillips recess head screws PZ 1 / 2 / 3.

Set contents 52720 199:1 BiTorsion holder Rapidaptor with quick-exchange mount N 1/4 inch / J 1/4 inch,

Q 2 bits diamond-coated for slotted screws 1,0 x 5,5 / 1,2 x 6,5 mm, D 2 bits diamond-coated for Phillips recess head screws PH 1 / 2, E 2 bits diamond-coated for Phillips recess head screws PZ 1 / 2.

Bit assortments Bit Check®

sTypeIn plastic case.

52720 199-201TypeWith BiTorsions holder Rapidaptor with quick-ex-change mount.

52720 208TypeWith multi-purpose adapter Rapidaptor with quick-exchange mount.

52720 203-206TypeWith multi-purpose adapter with quick-exchangemount.

52720 199

52720 201

52720 203

52720 204

52720 206

52720 208

52720

Stainless steel bit assortment Bit-Check®

sTypeIn plastic case. With stainless steel holder Rapi-daptor with quick-exchange mount for mounting in

the power screwdriver or in the drill chuck of theelectrical drill. 52728

Set contents 52728 101:1 stainless steel holder Rapidaptor with quick-exchange mount N 1/4 inch / J 1/4 inch,

J 4 bits for Allen screws size 2,5 / 3,0 / 4,0 / 5,0 mm, D 5 bits for Phillips recess head screws PH 2 x size 1 / 2 x size 2 / 1 x size 3.


10-part 101

52728

. Wera StainlessThe tool for better results.

sThe use of stainless steel averts corrosion. Stainless steel needs tools made of stainless steel.This is the only way to prevent corrosion caused by the abrasion of standard tools.

ß Hand tools


5

Bit assortments Bit-Safe®

s52725 098TypeWith multi-purpose adapter Rapidaptor with quick-exchange mount.

52725 104TypeWith multi-purpose adapter.

52725 098


61-part 09861-part 104

52725 104

52725

Set contents 52725 098:1 multi-purpose adapter Rapidaptor® with quick-exchange mount,

Q 1 ea. bit 0,6 x 4,5 / 1,0 x 5,5 / 1,2 x 6,5 mm, J 3 ea. bits size 2,5 / 3 / 4, J 2 bits size 5,D 3 bits PH 1 / 25, D 10 bits PH 2 / 25, D 2 bits PH 3 / 25, E 3 bits PZ 1 / 25, E 10 bits PZ 2 / 25, E 2 bits PZ 3 / 25, M 2 bits TX 10, M 3 ea. bits TX 15 / 20 / 25 / 30, M 2 bits TX 40.

Set contents 52725 104:1 multi-purpose adapter,

Q 1 ea. bit 0,6 x 4,5 / 1,0 x 5,5 / 1,2 x 6,5 mm,J 3 ea. bits size 2,5 / 3 / 4,J 2 bits size 5,D 3 bits PH 1 / 25,D 10 bits PH 2 / 25,D 2 bits PH 3 / 25,E 3 bits PZ 1 / 25,E 10 bits PZ 2 / 25,E 2 bits PZ 3 / 25,M 2 bits TX 10,M 3 ea. bits TX 15 / 20 / 25 / 30,M 2 bits TX 40.

Inkra bits 1/4 Inch (Drive C 6,3)

+TypePerfect torque transmission and reduced cam-outeffect. Even when working in a slanted position ofthe power tool or the screwdriver, virtually constantinsertion into the screw head.

52869 101-103ApplicationD Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-C 6,3,ISO 1173.Output: DIN 5260-PH, ISO 8764-PH.

52869 201-203Application E Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-C 6,3,ISO 1173.Output: DIN 5260-PZ, ISO 8764-PZ.

52869 101-103

Size Length 52869 …mm a

PH 1 25 10 pcs. 101PH 2 25 10 pcs. 102PH 3 25 10 pcs. 103PZ 1 25 10 pcs. 201PZ 2 25 10 pcs. 202PZ 3 25 10 pcs. 203

52869 201-203

Even when working in a slanted position, handling ismuch easier thanks to lower contact pressure.

Slippage and wear of the tip or the screw head arereduced.

52869

Set contents Equipped with Bit type 52720 …

7-part BiTorsion holder Rapidaptor BiTorsion, diamond-coated 19910-part BiTorsion holder Rapidaptor BiTorsion, strength-hard 20130-part multi-purpose adapter Rapidaptor Torsion, strength-hard 2087-part multi-purpose adapter strength-hard 203

10-part multi-purpose adapter Torsion, strength-hard 20410-part multi-purpose adapter Torsion, strength-hard 206

. a= Sales are restricted to the packaging units mentioned

in the catalogue. Purchase orders must be in units.

eng/OP

• Dura Bits • BiTorsion Bits • Extra hard Bits Torsionform

www.hhw.de52.38

5

Dura bits 1/4 Inch (Drive C 6,3)

+With torsion zone and a revolutionary coating. The strength-hard, elastic DURA-bit with extremely wear-resistant, patented carbide coating bites into thescrew head with finest micro carbide particles. Less slip-off and less pressure needed. Absorbing energy, the bit is protected against early damage. Particularlysuitable for serial screw fittings and for heavy-duty screwing works.

52790Application Q slotted screws. Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: DIN 5264-C, ISO 2380.


0,6 x 4,5 25 10 pcs. 2010,8 x 5,5 25 10 pcs. 2021,2 x 6,5 25 10 pcs. 204


PZ 1 25 10 pcs. 101PZ 2 25 10 pcs. 102PZ 3 25 10 pcs. 103


PH 1 25 10 pcs. 101PH 2 25 10 pcs. 102PH 3 25 10 pcs. 103


T 10 25 10 pcs. 101T 15 25 10 pcs. 102T 20 25 10 pcs. 103T 25 25 10 pcs. 104T 30 25 10 pcs. 105T 40 25 10 pcs. 106

52792Application D Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: DIN 5260-PH, ISO 8764-PH.

52794Application E Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: DIN 5260-PZ, ISO 8764-PZ.

52796Application M inner TORX® screws.

Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: TORX®.

52790 - 52796

52800Application Q slotted screws. Drive: 1/4 inch hexagon DIN 3126-C 6,3, suitable for holder in compliance with DIN 3126-D 6,3, ISO 1173.


0,8 x 5,5 25 10 pcs. 1011,0 x 5,5 25 10 pcs. 1021,2 x 6,5 25 10 pcs. 103





52802Application D Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-C 6,3, suitable for holder in compliance with DIN 3126-D 6,3, ISO 1173.

52804Application E Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-C 6,3, suitable for holder in compliance with DIN 3126-D 6,3, ISO 1173.

52807Application D Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-E 6,3, suitable for holder in compliance with DIN 3126-F 6,3, ISO 1173.

BiTorsion bits diamond-coated 1/4 inch (drive C 6,3 / E 6,3)52800 - 52815



sTypeBiTorsion for long service life, diamond-coated for a secure hold in the screw.The advantages:. Reduced wear of bit and screw head.. Less pressure needed, less slip-offs.. Reduction of working time.. Reduction of costs per screw.



ß Hand tools


5

52809Application E Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-E 6,3, suitable for holder in compliance with DIN 3126-F 6,3, ISO 1173.

52815Application M inner TORX® screws.Drive: 1/4 inch hexagon DIN 3126-C 6,3, suitable for holder in compliance with DIN 3126-D 6,3, ISO 1173.




T 10 25 10 pcs. 101T 15 25 10 pcs. 102T 20 25 10 pcs. 103T 25 25 10 pcs. 104T 30 25 10 pcs. 105T 40 25 10 pcs. 106

BiTorsion bits SIT 1/4 inch (drive C 6,3)

sType The SIT system was introduced under the name -AW-Profil- and has decisively improved the workwith Assy® and pias screws.(1) Better force transmission thanks to 6 contactsurfaces. Long service life thanks to narrowtolerances and high force transmission. (2) Quickinsertion and better fit thanks to slightly taperedscrew and bit. Lower cam-out-forces (highpressure to be put on the tool) thanks to improvedforce transmission and saft fit of the tool in thescrew. Easy handling thanks to colour codes.

BiTorsion for a long service life, strength-hard,especially suitable for harder application, e.g. insheet metal or metal.The advantages:. Reduced wear of bit and screw head.. Less pressure needed, less slip-offs.. Reduction of working time.. Reduction of costs per screw.

Application Assy®, pias screws. Drive: 1/4 inch hexagon DIN 3126-C 6,3, suitablefor holder in compliance with DIN 3126-D 6,3, ISO1173.

52818 101


SIT 10 25 10 pcs. 101SIT 20 25 10 pcs. 102SIT 25 25 10 pcs. 103SIT 30 25 10 pcs. 104

52818 102

52818 103

52818 104

52818

Extra hard bits Torsionsform 1/4 inch (drive C 6,3 / E 6,3)

TypeExtra hard bits, torsion with extremely high static torque. Torsion tip absorbes force peaks from tool head. Especially suitable for soft applications, e.g. in wood.

52822 - 52828

52822Application D Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-C 6,3, suitable for holder in compliance with DIN 3126-D 6,3, ISO 1173.

52824Application E Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-C 6,3, suitable for holder in compliance with DIN 3126-D 6,3, ISO 1173.

52826Application D Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-E 6,3, suitable for holder in compliance with DIN 3126-F 6,3, ISO 1173.

52828Application E Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-E 6,3, suitable for holder in compliance with DIN 3126-F 6,3, ISO 1173.











eng/OP

• Strenght hard bits Torsion • Strenght hard bits extra long

www.hhw.de52.40

Strength hard bits, Torsion 1/4 inch (Drive C 6,3/E 6,3)

TypeStrength-hard bits in torsion form for tough screwing applications. Torsion tip absorbes force peaks from tool head.

52835Application Q slotted screws.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: DIN 5264-C, ISO 2380.


0,5 x 4,0 25 10 pcs. 1010,6 x 4,5 25 10 pcs. 1020,8 x 5,5 25 10 pcs. 1031,0 x 5,5 25 10 pcs. 1041,2 x 6,5 25 10 pcs. 1051,6 x 8,0 25 10 pcs. 106









52841Application D ACR Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: DIN 5260-PH, ISO 8764-PH.

52843Application E ACR Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: DIN 5260-PZ, ISO 8764-PZ.

52845Application D Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-E 6,3, ISO 1173Output: DIN 5260-PH, ISO 8764-PH.

52846Application E Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-E 6,3,ISO 1173.Output: DIN 5260-PZ, ISO 8764-PZ.

52835 - 52846








Tool carts by ATORN:

ATORN‘s high-quality workshop furnishings.



5

ß Hand tools

eng/OP

52850Application Q slotted screws.Drive: 1/4 inch hexagon DIN 3126-E 6,3, ISO 1173.Output: DIN 5264-C, ISO 2380.

Size Length 52852 …approx. mm a

PH 1 70 10 pcs. 101L PH 1 89 10 pcs. 102

XL PH 1 127 10 pcs. 103XXL PH 1 152 10 pcs. 104

PH 2 70 10 pcs. 105L PH 2 89 10 pcs. 106

XL PH 2 110 10 pcs. 107XXL PH 2 127 10 pcs. 108

XXXL PH 2 152 10 pcs. 109PH 3 70 10 pcs. 110

L PH 3 89 10 pcs. 111XL PH 3 110 10 pcs. 112

XXL PH 3 152 10 pcs. 113


PZ 1 70 10 pcs. 101L PZ 1 89 10 pcs. 102

XL PZ 1 127 10 pcs. 103XXL PZ 1 152 10 pcs. 104

PZ 2 70 10 pcs. 105L PZ 2 89 10 pcs. 106

XXL PZ 2 127 10 pcs. 108XXXL PZ 2 152 10 pcs. 109

PZ 3 70 10 pcs. 110L PZ 3 89 10 pcs. 111

XXL PZ 3 152 10 pcs. 113


T 8 50 10 pcs. 101L T 8 70 10 pcs. 102

XL T 8 89 10 pcs. 103XXL T 8 152 10 pcs. 104

T 10 50 10 pcs. 105L T 10 70 10 pcs. 106

XL T 10 89 10 pcs. 107XXL T 10 152 10 pcs. 108

T 15 50 10 pcs. 109L T 15 70 10 pcs. 110

XL T 15 89 10 pcs. 111XXL T 15 152 10 pcs. 112

T 20 50 10 pcs. 113L T 20 70 10 pcs. 114

XL T 20 89 10 pcs. 115XXL T 20 152 10 pcs. 116

T 25 50 10 pcs. 117L T 25 70 10 pcs. 118

XL T 25 89 10 pcs. 119XXL T 25 152 10 pcs. 120

T 27 50 10 pcs. 121L T 27 70 10 pcs. 122

XL T 27 89 10 pcs. 123XXL T 27 152 10 pcs. 124

T 30 50 10 pcs. 125L T 30 70 10 pcs. 126

XL T 30 89 10 pcs. 127XXL T 30 152 10 pcs. 128

T 40 50 10 pcs. 129L T 40 70 10 pcs. 130

XL T 40 89 10 pcs. 131XXL T 40 152 10 pcs. 132

52854Application E Phillips recess head screws PZ.Drive: 1/4 inch hexagon DIN 3126-E 6,3, ISO 1173.Output: DIN 5260-PZ, ISO 8764-PZ.

52852Application D Phillips recess head screws PH.Drive: 1/4 inch hexagon DIN 3126-E 6,3, ISO 1173.Output: DIN 5260-PH, ISO 8764-PH.

52856Application M inner TORX® screwsDrive: 1/4 inch hexagon DIN 3126-E 6,3, ISO 1173.Output: TORX®.


0,5 x 3,0 50 10 pcs. 101L 0,5 x 3,0 70 10 pcs. 102

0,5 x 4,0 50 10 pcs. 1030,6 x 3,5 50 10 pcs. 104

L 0,6 x 3,5 70 10 pcs. 105XL 0,6 x 3,5 152 10 pcs. 106

0,6 x 4,5 50 10 pcs. 1070,8 x 4,0 50 10 pcs. 108

L 0,8 x 4,0 70 10 pcs. 109XL 0,8 x 4,0 89 10 pcs. 110

XXL 0,8 x 4,0 152 10 pcs. 1110,8 x 5,5 50 10 pcs. 1121,0 x 5,5 50 10 pcs. 113

L 1,0 x 5,5 70 10 pcs. 114XL 1,0 x 5,5 89 10 pcs. 115

XXL 1,0 x 5,5 152 10 pcs. 1161,2 x 6,5 50 10 pcs. 117

L 1,2 x 6,5 70 10 pcs. 118XL 1,2 x 6,5 152 10 pcs. 119

1,2 x 8,0 50 10 pcs. 120L 1,2 x 8,0 89 10 pcs. 121

1,6 x 8,0 50 10 pcs. 122L 1,6 x 8,0 89 10 pcs. 123

Strength-hard bits extra long 1/4 inch (drive E 6,3)

TypeStrength-hard bits in torsion form for tough screwing applications. Bits absorb high torques on screw-head.

52850 - 52856


in the catalogue. Purchase orders must be in units. www.hhw.de 52.41

5

eng/OP

• Strenght hard bits • Standard Bits

www.hhw.de52.42

5

Strength hard bits 1/4 inch (drive C 6,3)

TypeStrength-hard bits for tough screwing applications. Bits absorb high torques on screw-head.

52858Application & TRI-WING® screws. Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173. Output: TRI-WING®.


1 25 10 pcs. 1012 25 10 pcs. 1023 25 10 pcs. 1034 25 10 pcs. 1045 25 10 pcs. 1056 32 10 pcs. 1067 32 10 pcs. 1078 32 10 pcs. 108


6 25 10 pcs. 1018 25 10 pcs. 102

10 25 10 pcs. 1031/4 inch 25 10 pcs. 104


1,5 25 10 pcs. 1012,0 25 10 pcs. 1022,5 25 10 pcs. 1033,0 25 10 pcs. 1044,0 25 10 pcs. 1055,0 25 10 pcs. 1066,0 25 10 pcs. 1078,0 25 10 pcs. 108

10,0 25 10 pcs. 109


2,5 25 10 pcs. 1013,0 25 10 pcs. 1024,0 25 10 pcs. 1035,0 25 10 pcs. 1046,0 25 10 pcs. 105

52864Application Inner TORX® screws with pilot (BO).Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: TORX®, with borehole in the driving tip.

52859 Application % TORQ-SET®Mplus screws.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173. Output: TORQ-SET®Mplus.

52865 Application M inner TORX PLUS® screws. Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173. Output: TORX PLUS®.

52860Application J Allen screws.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: outer hexagon.

52861Application J Allen screws.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: ball head.

52862 Square bitsApplication P inner square screws Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173. Output: outer square.

52858 - 52865

Size Length Square for inner square 52862 …mm mm screws mm a

00 25 1,27 1,4 10 pcs. 1010 25 1,78 2,0 10 pcs. 1021 25 2,31 2,5 10 pcs. 1032 25 2,85 3,1 10 pcs. 1043 25 3,37 3,7 10 pcs. 1054 25 4,84 5,1 10 pcs. 106


IP 6 25 10 pcs. 101IP 7 25 10 pcs. 102IP 8 25 10 pcs. 103IP 9 25 10 pcs. 104

IP 10 25 10 pcs. 105IP 15 25 10 pcs. 106


IP 20 25 10 pcs. 107IP 25 25 10 pcs. 108IP 27 25 10 pcs. 109IP 30 25 10 pcs. 110IP 40 25 10 pcs. 111


T 10 25 10 pcs. 101T 15 25 10 pcs. 102T 20 25 10 pcs. 103T 25 25 10 pcs. 104T 27 25 10 pcs. 105T 30 25 10 pcs. 106T 40 25 10 pcs. 107



ß Hand tools


5

Standard Bits 1/4 Inch (Drive C 6,3/E 6,3)

TypeThe bits fulfil all requirements of DIN and ISO standards.

ApplicationFor all common powered screwdriver tools.

52870Application Q slotted screws.Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: DIN 5264-C, ISO 2380.


0,6 x 4,5 25 10 pcs. 1010,8 x 5,5 25 10 pcs. 1021,0 x 5,5 25 10 pcs. 1031,2 x 6,5 25 10 pcs. 1041,6 x 8,0 25 10 pcs. 105


PH 0 25 10 pcs. 100PH 1 25 10 pcs. 101PH 2 25 10 pcs. 102PH 3 25 10 pcs. 103


PZ 0 25 10 pcs. 100PZ 1 25 10 pcs. 101PZ 2 25 10 pcs. 102PZ 3 25 10 pcs. 103


3 25 10 pcs. 2014 25 10 pcs. 2025 25 10 pcs. 2036 25 10 pcs. 2047 25 10 pcs. 2058 25 10 pcs. 206

52876Application J Allen screws. Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173. Output: outer hexagon.


52878Application H XZN Trisquare screws. Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173. Output: XZN.



Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173.Output: TORX®.

52881 Application M inner TORX® screws.

Drive: 1/4 inch hexagon DIN 3126-C 6,3, ISO 1173. Output: TORX®.

52882 Application Inner TORX® screws with pilot (BO). Drive: 1/4 inch hexagon DIN 3126-E 6,3, ISO 1173. Output: TORX®, with borehole in the driving tip.

52870 - 52882


M 4 25 10 pcs. 201M 5 25 10 pcs. 202M 6 25 10 pcs. 203M 8 25 10 pcs. 204

M 10 25 10 pcs. 205





T 10 25 10 pcs. 108T 15 25 10 pcs. 109T 20 25 10 pcs. 110


T 7H 50 10 pcs. 101T 8H 50 10 pcs. 102T 9H 50 10 pcs. 103

T 10H 50 10 pcs. 104T 15H 50 10 pcs. 105T 20H 50 10 pcs. 106



eng/OP

• Strenght hard bits • Bit Holders • Bit Ratchet screwdrivers

Strength-hard bits 5/16 inch (drive C 8)

TypeStrength-hard bits for tough screwing applications. Bits absorb high torques on screw-head.

52889Application E Phillips recess head screws PZ.Drive: 5/16 inch hexagon DIN 3126-C 8, ISO 1173.Output: DIN 5260-PZ, ISO 8764-PZ.


0,8 x 5,5 41 10 pcs. 1011,0 x 5,5 41 10 pcs. 1021,2 x 6,5 41 10 pcs. 103

1,6 x 10,0 41 10 pcs. 1062,0 x 12,0 41 10 pcs. 1072,5 x 14,0 41 10 pcs. 108




PZ 1 32 10 pcs. 101PZ 2 32 10 pcs. 102PZ 3 32 10 pcs. 103PZ 4 32 10 pcs. 104


T 20 35 10 pcs. 101T 25 35 10 pcs. 102T 27 35 10 pcs. 103T 30 35 10 pcs. 104T 40 35 10 pcs. 105T 45 35 10 pcs. 106T 50 35 10 pcs. 107T 55 35 10 pcs. 108T 60 35 10 pcs. 109

52885Application Q slotted screws.Drive: 5/16 inch hexagon DIN 3126-C 8, ISO 1173.Output: DIN 5264-C, ISO 2380.


Drive: 5/16 inch hexagon DIN 3126-C 8, ISO 1173.Output: TORX®.

52887Application D Phillips recess head screws PH.Drive: 5/16 inch hexagon DIN 3126-C 8, ISO 1173.Output: DIN 5260-PH, ISO 8764-PH.

52893Application J Allen screws.Drive: 5/16 inch hexagon DIN 3126-C 8, ISO 1173.Output: outer hexagon.

52885 - 52893

Bit holder

52897

Blade length Overall length 52897 … 52899 …mm mm120 218 101120 232 101

52899

52897 - 52899

52901

Blade length Overall length 52901 …mm mm100 218 101

Bit holders

sTypeSoft zone Kraftform® handle with roll stop andintegrated bit holder. The bayonet blade can bepartly pushed into the handle, with 1/4 inch outsidehexagon and Rapidaptor® quick-exchange mount.

Contents:1 bit ea. for slotted screws 1,0x5,5 / 1,2x6,5 mm,1 bit ea. for Phillips recess head screws PH 1 / 2,1 bit ea. for Phillips recess head screws PZ 1 / 2.ApplicationFor mounting 1/4 inch bits DIN 3126-C and -E 6,3, ISO 1173.

52901


3 30 10 pcs. 1014 30 10 pcs. 1025 30 10 pcs. 1036 30 10 pcs. 1048 30 10 pcs. 105

10 30 10 pcs. 106

s52897TypeWith strong permanent magnet and hexagonalblade, nicromatt. With 1/4 inch outside hexagon incompliance with DIN 3126-D 6,3 and Kraftform®

handle with roll stop, multi-component.ApplicationFor mounting 1/4 inch bits DIN 3126-C 6,3, ISO1173.

52899TypeWith quick-exchange mount, magnetic, hexagonalblade and hexagonal shoulder at handle end forusing a wrench. With 1/4 inch outside hexagon incompliance with DIN 3126-D 6,3 and Kraftform®handle with roll stop, multi-component.ApplicationFor mounting 1/4 inch bits DIN 3126-C 6,3 and -E6,3, ISO 1173.


in the catalogue. Purchase orders must be in units.www.hhw.de52.44

5

ß Hand tools


Bit holders

52902

52902 …

201

52902

Bit holders

+TypeHexagon blade with magnetic holder. Ergonomically-shaped SoftFinish multi-component handle with rollstop. Folding bit magazine in handle, easy removalof bits and secure storage of up to 8 bits.

Contents:1 bit for slotted screws 6,5 mm,3 bits for Phillips recess head screws PH 1 / 2 / 3,1 bit for Phillips recess head screws PZ 2,3 bits for TORX® screws TX 15 / 20 / 25.ApplicationFor mounting 1/4 inch bits DIN 3126-C 6,3, ISO1173.

52912

52912 …

101

52912

ESD bit holders

+TypeWiha SoftFinish® ESD multi-component handlewith roll stop. With quick-exchange mountRapidFix, 1/4 inch outside hexagon in compliancewith DIN 3126, ISO 1173, shape D 6,3.

ApplicationFor application with electronic construction partswith risk of electrostatics. Complies with EN 100-015 part 1. For mounting 1/4 inch bits DIN 3126-C 6,3,ISO 1173. Compact, practical shape for working inhard-to-reach places.

52900

52900 …

101

52900

52919 …

101

Bit ratchet screwdriver52919

,TypeShort, compact handle. 1/4 inch magnetic bit holder.Clockwise and counterclockwise operation.ApplicationFor mounting 1/4 inch bits DIN 3126-C 6,3, ISO 1173.

52919

52920 …

101

Bit ratchet screwdriver52920

,TypeAllen screwdriver with magnet. Push-button LED's.Bit magazine in handle.Contents:2 bits for slotted screws 4,5 / 5,5 mm,2 bits for Phillips recess head screws PH 1 / 2,2 bits for Phillips recess head screws PZ 1 / 2.

ApplicationFor mounting 1/4 inch bits DIN 3126-C 6,3, ISO1173.

52920

BType With 1/4 inch outside hexagon in compliance withDIN 3126-D 6,3. Telescopic magazine for 7 bits.Smooth cap without seams for less friction. Ergono-mically-shaped handle.

Contents:3 bits for slotted screws 0,6x4,5 / 1,0x55 /

1,2x6,5 mm,3 bits for Phillips recess head screws PH 0 / 1 / 2, 2 bits for Phillips recess head screws PZ 1 / 2. Application For mounting 1/4 inch bits DIN 3126-C 6,3, ISO1173.

5

eng/OP

• Bit Holder • Bit Ratchet

www.hhw.de52.46

5Reversible bit ratchets

VTypeWith reverse lever. Surface chrome-plated, polished.ApplicationFor mounting bits.QualityChrome-vanadium steel.

52914Type1/4 inch drive, 20 teeth.

52915Type5/16 inch drive, 30 teeth.

52914

Drive Overall length 52914 … 52915 …inch mm

1/4 115 1015/16 200 101

52915

52914 - 52915

Bit reversible ratchet

VType With magnet, clockwise and counterclockwiseoperation, flat shape, glossy chrome-plated.

Application For screwdriver bits. Quality Special steel.

52906

Drive 52906 …inch

1/4 + 5/16 101

52906

Bit ratchet wrench

TypeWith magnet, for clockwise and counterclockwiseoperation, offset, chrome-plated.

ApplicationWith Allen key mount for screwdriver socket wrenchbits.

52910

Drive Overall length 52910 …inch mm

1/4 + 5/16 138 101

52910

ESD bit holders

sType With 1/4 inch outside hexagon in compliance withDIN 3126-D 6,3 and circlip. Kraftform Weralit ESDhandleApplication For application with electronic construction partswith risk of electrostatics. Complies with EN 100-015 part 1.

For mounting 1/4 inch bits DIN 3126-C 6,3, ISO1173.

52904 201Type Extra short.

52904 202Type Hexagonal blade, nicromatt, with roll stop.

52904 201

Blade length Overall length 52904 …mm mm

10 64 201100 212 202

52904 202

52904

Bit ratchet

TypeCan be switched to clockwise, counterclockwise andblocked operation. Allen socket with magnet, forscrewdriver bits with outer hexagon 1/4 inch DIN3126/ISO 1173 shape C 6,3. For the application with1/4 inch socket wrench bits the connector cat.-no.52932 101 (outer hexagonal and outer square 1/4

inch) may be used..ApplicationThe ratchet has a knurled quick-action mechanismfor pre-screwing. Serrated, high-quality mechanismwith a working angle of 30°. Ergonomically shapedhandle with 1/4 inch square drive for operation withT-handle, extension pieces etc.

52905

Overall length 52905 …mm

206,5 101

52905

ß Hand tools


5

Readyflex® Freiraumknarre®

PTypeWith direct mounting of bits. DIN 3126 D 6,3.Steerable, 7 switch steps via flex-stop Variomatic(handle-lock automatic).ApplicationDue to low construction height by direct mounting,this ratchet is for special use within hard-to-reachplaces. For all screwing applications in industry andtrade.

QualityChrome-vanadium steel. 52907

52907 …

101

52907

Bit reversible ratchet

TypeReversible, 22 teeth, with steel handle and Allensocket 1/4 inch, DIN 3126, ISO 1173, shape D 6,3.Allen wrench with pressure spring (DBGM).Bits areeasy to insert, lock in place safely and are effortlessto remove. Also hexagonal shafts with wide grooves(DIN 3126, ISO 1173, shape E).

ApplicationFor screwdriver bits. 52908

Overall length 52908 …mm117 101

52908

. s The RapidaptorFaster, safer, easier exchange of bits.The Rapidaptor holders are a convincing improvement over the tested and proven multi-purpose adapters with quick-exchange mount. Because the Rapidaptor technology combines five decisive advantages.

Rapid-in and self-lock The bit can beinserted into themount withoutmoving the sleeve.As soon as the bit isinserted into thescrew, it is lockedand fits secure andwithout wobbling.

Rapid-outIn order to exchangethe bit, just slide thesleeve forward: Thespring mechanism liftsthe bit from the magnetand unlocks the tool.The bit can easily beremoved. The Rapid-out function allows foreasy removal even ofthe smallest bit sizes(such as PH 0 or TX 5)without using additionaltools..

Rapid-spinThe freewheelingapplication sleeveallows the user toguide the drill with thesleeve during thescrewing work. Thisfacilitates the insertioninto the screw andreduces the danger ofslipping off.

Chuck-allThe Rapidaptor® quick-change toolholder take1/4 inch bits incompliance with DIN3126-C 6,3 as well as E 6,3.

Single HandAll functions of theRapidaptor® quick-change toolholder suchas bit insertion orremoval can beperformed with onehand only. This quicker,more economical andergonomical: Not amovement too much.

Rapidaptor® withring magnet (cat.-no. 52913 093)The floating,freewheeling magneticsleeve ensures greathold even with largeand heavy screws:This allows forlightning-quickapplication.Thedangerous and painfulholding of the screwfor the application isno longer necessary.Perfect for overheadwork.

eng/OP

• Bit Holder • Connectors • Impact screwdriver

www.hhw.de52.48

5

Multi-purpose bit holder

52916DIN 7427-C, with circlip.

52918 102-108With special steel sleeve and strong permanentmagnet.

52918 110With sleeve made of beryllium and strong perma-nent magnet. Suitable for servo screwdrivers.

52918 102

With circlip with permanent magnetDrive DIN Output DIN Length mm 52916 … 52918 …

3126 inch 3126 (with magnet)5,5 J A 5,5 1/4 N D 6,3 – (72) 102

1/4 inch J E 6,3 1/4 N D 6,3 57 (50) 103 1031/4 inch J E 6,3 1/4 N D 6,3 – (74) 104

5/16 inch J – 1/4 N D 6,3 – (45) 105Ø 7 9 G 7 1/4 N D 6,3 – (75) 107SDS , – 1/4 N D 6,3 – (79) 108

1/4 inch J E 6,3 1/4 N D 6,3 – (75) 110

52918 103

52918 104

52918 105

52918 107

52918 108

52918 110

52916 - 52918

Connectors with outer square52932

Drive DIN Output DIN Length 52932 …3126 inch 3120/3126 mm

1/4 inch J C 6,3 1/4 z A 6,3/ – 25 1011/4 inch J E 6,3 1/4 z – / E 6,3 50 1021/4 inch J E 6,3 1/4 z – / E 6,3 100 1031/4 inch J E 6,3 3/8 z – / E 10 50 1041/4 inch J E 6,3 3/8 z – / E 10 100 105

Ø 7 9 G 7 1/4 z – / E 6,3 75 106Ø 7 9 G 7 3/8 z – / E 10 75 107SDS , – 1/4 z – / E 6,3 70 108

SDS max – 1/2 z – 95 109

52932 101 52932 102-105

52932 106-107

52932 108

52932 109

Bit holder with quick-exchange mount.

ApplicationQuick-exchange holders provide a stable and rigidconnection between holder and bit. Simultane-ously, a slight move of the clamping sleeve releasesthe lock and allows quick exchange of the tool.

52913 096sRapidaptorTypeWith quick-exchange mount and strong permanentmagnet.

52913 093sRapidaptor with ring magnetTypeWith quick-exchange mount and special sleeve.ApplicationFor lightning-quick application and secure seat ofthe screw on the holder. Ideal for overhead work orfor screwing in long screws.

52913 094sRapidaptor BiTorsionTypeWith quick-exchange mount. Output 1/4 inch Allenwith Wera quick-exchange mount Rapidaptor.

ApplicationAn integrated torsion zone reliably absorbs loadeffects and reduces therefore the risk of earlydamage of the tool. Lower cycle times andreplacements.

52913 095sRapidaptor stainless steelTypeWith quick-exchange mount. ApplicationThe usage of stainless steel bits reduces the dangerof corrosion stripes or pitting due to corrosioncaused by using standard bits with stainless steelscrews.

52913 091 +CentroFix, magneticType Metal sleeve, coated. Application For applications where the bit must hold in placesecurely.Optimised for the application with long bitsand drill bits. Thanks to the special holding mecha-nism, this bit holder can hold all types of bits with1/4 inch hexagon drive. The play between bit andholder is reduced to a minimum. One-hand operati-on for quick exchange of bits.

52913 096 52913 103

52913 093 52913 104

52913 094 52913 105

52913 095 52913 107

52913 091

Drive DIN Output DIN Length 52913 …3126 inch 3126 mm

1/4 inch J E 6,3 1/4 N D 6,3/F 6,3 50 0961/4 inch J E 6,3 1/4 N D 6,3/F 6,3 57 0931/4 inch J E 6,3 1/4 N D 6,3/F 6,3 75 0941/4 inch J E 6,3 1/4 N D 6,3/F 6,3 50 0951/4 inch J E 6,3 1/4 N D 6,3/F 6,3 60 091

Drive DIN Output DIN Length 52913 …3126 inch 3126 mm

1/4 inch J E 6,3 1/4 N D 6,3 74 1031/4 inch J E 6,3 1/4 N D 6,3 50 104

5/16 inch J – 1/4 N D 6,3 47 105Ø 7 9 G 7 1/4 N D 6,3 77 107

52913

ß Hand tools


5

Bit holder with square drive

52935With quick-exchange mount.

52937Allen socket with ball stopfor mounting bits.

52938

0Allen socket with holding springfor mounting bits.

52939

Allen socket with pressure springfor mounting bits.QualityChrome-alloy steel.

52940,Allen socket with spring washers for mounting ofbits.

0 ,

Drive DIN Output DIN 52935 … 52937 … 52938 … 52939 … 52940 …inch 3121 inch 3126

1/4 . G 6,3 1/4 N D 6,3 101 101 101 101 1013/8 . G 10 1/4 N D 6,3 102 102 1023/8 . G 10 5/16 N D 8 103 1031/2 . G 12,5 1/4 N D 6,3 104 1041/2 . G 12,5 5/16 N D 8 105

52937

5293952935

52938

52940

52935 - 52940

Hexagonal socket wrench bits E 6,3

sDrive: 1/4 inch hexagon, suitable for holder incompliance with DIN 3126-F 6,3, ISO 1173.ApplicationFor outer hexagons.

52980 103-122 Non-magnetic.

52980 201-212 With strong permanent magnet.

52980 103-122

with magnetSize inch Overall length Ø 52980 … 52980 …mm mm mm5,5 - 50 11,0 103 201

6 - 50 11,0 104 2027 - 50 11,0 106 2038 - 50 12,5 107 2049 - 50 14,0 108 205

10 - 50 14,0 110 20611 - 50 16,0 111 20712 - 50 18,0 113 20813 - 50 18,0 115 209

- 1/4 50 11,0 120 210- 5/16 50 12,5 121 211- 3/8 50 14,0 122 212

52980 201-212

52980

Sets of impact screwdrivers

sApplicationTo loosen and tighten seized screws.

5294811-part, in sheet steel box.

5295113-part, in sheet steel box.

52948

Set contents 52948:1 impact screwdriver 5/16 inch hexagonal drive,1 adapter 5/16 inch hexagonal drive x 3/8 inch square output,

Q 6 bits for slotted screws 5,5 x 1,0 / 6,5 x 1,2 / 8 x 1,6 / 10 x 1,6 / 12 x 2,0 / 14 x 2,5 mm, D 3 bits for Phillips recess head screws size 2 / 3 / 4.

Set contents 52951:1 impact screwdriver 1/2 inch hexagonal drive, 1 adapter 1/2 inch hexagonal drive x 1/2 inch square output,

Q 6 bits for slotted screws 9 x 1,4 / 10 x 1,6 / 13 x 1,5 / 13 x 2,0 / 16 x 2,5 / 18 x 3,0 mm,D 2 bits for Phillips recess head screws size 3 / 4,J 3 bits for Allen screws size 10 / 12 / 14 mm.

5/16 inch 1/2 inchSet contents 52948 … 52951 …

11-part 10113-part 101

52948 - 52951

eng/OP

• Impact screwdriver • Bar clamps

www.hhw.de52.50

5 Impact screwdriver bits for Phillips screws

sApplicationFor usage in impact screwdrivers.

52962Drive: 5/16 inch hexagon.


52962 - 52964

5/16 inch 1/2 inchSize 52962 … 52964 …

PH 1 101PH 2 102

5/16 inch 1/2 inchSize 52962 … 52964 …

PH 3 103 103PH 4 104 104

52962 - 52964

Impact screwdriver bits for Allen screws

52966

5/16 inchSize 52966 …mm

5 1016 102

5/16 inchSize 52966 …mm

8 10310 104

52966

sDrive: 5/16 inch hexagon.ApplicationFor usage in impact screwdrivers.

Impact screwdriver

sApplicationTo loosen and tighten seized screws.

52954 101

Hexagon drive for torque 52954 …inch screws Nm5/16 M 4 - 8 90 1011/2 M 6 - 14 180 102

52954 102

52954

Impact screwdriver bits for slotted screws52957 - 52959

sApplicationFor usage in impact screwdrivers.



52957 - 52959

5/16 inch 1/2 inchCutting edge thickness x width 52957 … 52959 …

mm1,0 x 5,5 1011,2 x 6,5 1021,6 x 8,0 1031,4 x 9,0 103

1,6 x 10,0 104 104

5/16 inch 1/2 inchCutting edge thickness x width 52957 … 52959 …

mm2,0 x 12,0 1052,0 x 13,0 1072,5 x 14,0 1082,5 x 16,0 1093,0 x 18,0 110




Documents

52002 Magnetic dish 52000 - HOMMEL HERCULES