Angle Body Valves & Proportional Control Valves€¦ · Size DN Cv Kv Min psi bar psi bar psi bar psi bar mm port Bronze (1) (2) lbs inch (mm) (m 3 /h) dia bsp 1/2 0.59 15 4.1 3.6

Angle Body Valves &Proportional Control ValvesAngle Body Valves &Proportional Control ValvesSkinner ValveTM

TABLE OF CONTENTS

General Information.......................................................1

Introduction and Key Features....................................1-2Valve Ordering Information.............................................3

Angle Body Valves..........................................................4

Series 810..................................................................4-11Series 820................................................................12-18

Control Valve Accessories............................................21

3 Way Direct Acting Pilot Control Valves.......................22

Electrical Specifications...............................................23Coil Enclosures.............................................................24

Technical Information..................................................25

Operating Principles................................................25-27

Offer of Sale.................................................................28

Series 810 & 820Series 810 & 820Series 810 & 820Series 810 & 820Series 810 & 820

WARNING

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR

RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.

This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or systems options for furtherinvestigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or systemin the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, issolely responsible for making the final selection of the products and systems and assuring that all performance. safety and warning requirements of the application are met.

The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker HannifinCorporation and its subsidiaries at anytime without notice.

!

Introduction and Key Features

1

The Parker Angle Body Valves consist of a family of externally pneumatically piloted 2-way angle bodyvalves available for on – off or proportional control applications, powered pneumatically or electrically.Available with stainless steel or bronze bodies with metallic actuator housings, the Parker valves meet adiverse range of applications.

The portfolio is endowed with numerous benefits including:A full-line of normally closed and normally open valves ranging in size from 1/2 inch to 3 inches.State of the art performance for long life, ease of service and tighter system integrity.Operating pressures up to 580- psi.Suitable for temperatures ranging from –40°F to 430°F.Handles millions of cycles for high temperature and aggressive media.Proportional control capability with pneumatic (p/p), electro-pneumatic (e/p) anddigital i/p integral positioners.Pilot valves for both AC & DC requirements.Complete line of high temperature watertight coil designs suitable for allpilot control valves.Fully repairable with discrete repair kits and supporting tools available.

The Parker Valves are constructed of the highest quality materials available for exceptional quality, longlife and reliability. All components are rigorously qualified based on the international standard ISO9001certification processes providing rigorous standards for design, development, manufacturing and testing.High quality you’ve come to expect from Parker.

Angle body valves are suitable for many process & industrial application requirements. Relevant on-offand proportional control valve applications include but are not limited to the following areas:

Food and Beverage Processing: − Brewery – water, steam, pasteurization, glycol solutions for cooling, de-aeration processes,

blending, carbonation, thermal processes− Bottling & bottle washing equipment− “Clean-in-Place” systems− Diary product processing

Water technology & treatment:− Filtration technology− Pollution control equipment

Textile Industry:− Bleaching, dyeing & drying equipment – steam, water & additives requirements

Cooling systems on injection molding machinesPharmaceutical & cosmetic industryChemical Process technologyRefrigeration & Cooling heat exchangersSterilizers – steam supply up to 430°FWater applications: Mining, Cement / concrete systems, Pulp & paperGeneral industrial applications of aggressive fluids with stainless materialsIndustrial Laundry EquipmentIndustrial Air Dryers

Introduction and Key Features

2

Normally Closed Version Shown

Valve Ordering Information

3

ANGLE BODY VALVE NOMENCLATURE

The numbering system allows every user an easy method to identify, select and understand the valve beingpurchased. Reference page 18 in this catalog for complete part numbering details and accessories.

Ordering Angle Body Valves

The angle body valve line uses a significant numbering system that allows every user an easy method to select,identify, and understand the product being purchased.

Select the angle body valve based on the application requirements. The catalog number is specified in theindividual specification table.

Example:

Designation 810 V B N 08 T 1 2 0 B H 0 0 0

Positions 1-3 4 5 6 7-8 9 10 11 12 13 14 15 16 17

Series 810 valve, on-off valve, bronze body material, 1/2” npt, PTFE seal, closing with flow, brass chromeactuator, high temp. seals, no other accessories

Position Description

1-3 Product Series Series 810

4 Valve, Actuator, Repair Valve V

5 Body Material Bronze B

6 Connection Type NPT N

7-8 Port / Orifice Size 1/2” 08

9 Seal Material PTFE T

10 Pilot Function Closing with flow 1

11 Actuator Diameter 50mm 2

12 Springs Standard 0

13 Actuator Housing Brass Chrome Plated B

14 Temperature Version High Temperature H

15 Packing Standard 0

16 Accessories – 810 series None 0

17 Additional Options None 0

Reference Angle Body Valve Numbering Table for complete part numberingdetails and optional accessories.

Series 810: 2 Way Angle Body Valves: 1/2” to 3” NPT

4

FEATURES• Compact design, high flow rates• Visual position indicator standard• For temperatures from – 22°F to +430°F / -30°C to 221°C• Working pressures up to 580 psi• Damped closing anti-water hammer design (fluid under seat)• Metal actuator housing for exceptional durability in steam & mildly aggressive applications• Valves satisfy the Pressure Equipment Directive 97/23/EC• Mountable in any position• Tight shut-off and Long Service Life• Actuator and valve components fully repairable

Technical Specifications

Options• Electrical position indicators

• Inductive proximity switches

• Mechanical limit switches

• Manual override

• Oil and Grease free version

• Ultra High Temp. (PEEK)

• Stroke limiter

Body Material Bronze Rg5 AISI 316L BrassFunction 2/2 NC, NO 2/2 NC, NO 2/2 NC, NONominal sizes 1/2" - 2" 1/2" - 2 1/2" 2 1/2" and 3"Connections:NPT thread standard 1/2" - 2" 1/2" - 2 1/2" 2 1/2" - 3"BSP thread (ISO228/1)SAE Tri clampTube endsFlanges ANSI 150Nominal Pressure 235 psi (16 bar) 580 psi (40 bar) 235 psi (16 bar)Differential Pressure See Specifications tablesPilot Pressure up to 145 psi (10bar) reference graphsActuator: 2" & 3" brass plated 2" & 3" brass plated 5" aluminum anodized

^Optional ^ Stainless Actuator

Max. fluid temperature -22°F (-30°C) up to 392°F (200°C)

-22°F (-30°C) up to 392°F (200°C)

-22°F (-30°C) up to 392°F (200°C)

#Optional # to -40°F (-40°C) # to -40°F (-40°C) # to -40°F (-40°C)*Optional * Up to +430°F (221°C)

Ambient temperature -22°F (-30°C) up to +140°F (60°C)Seal MaterialPacking GlandViscosity of the fluidVacuumWorking pressure forinverted packing for vacuum serviceLeakageInstallationOptical Position IndicatorPilot Control Media

Fluids Inert gases, hot water, oils, steam

Aggressive & corrosive fluids

Inert gases, hot water, oils, steam

ANSI Class VI shutoffAny position

Standard all sizesAir, neutral gas, water

maximum 175 psi

PTFEPTFE / Graphite

maximum 600 mm²/s (600cSt, 80°E, 2700 SSU)maximum 0.0295 mercury (Hg)


5

Series 810 Operating Data: Normally Closed, Flow Direction Under SeatRecommended for liquids and anti water-hammer application needsBRONZE / BRASS * BODY VALVES

Port Orifice Size Valve Number Wt. Size DN Cv Kv Min psi bar psi bar psi bar psi bar mm port Bronze (1) (2) lbs

inch (mm) (m3/h) dia bsp1/2 0.59 15 4.1 3.6 0 232 16.0 232 16.0 - - 51-145 3.5-10 50 1/8 810VBN08T320BH000 2.43/4 0.78 20 9.2 8.0 0 190 13.0 190 13.0 - - 65-145 4.5-10 50 1/8 810VBN12T320BH000 2.61 1.00 25 17.3 15.0 0 85 5.8 85 5.8 - - 65-145 4.5-10 50 1/8 810VBN16T320BH000 3.1

1-1/4 1.25 32 24.3 21.0 0 75 5.2 75 5.2 - - 85-145 5.7-10 50 1/8 810VBN20T320BH000 4.01-1/2 1.56 40 40.4 35.0 0 100 7.0 100 7.0 - - 51-145 3.5-10 80 1/4 810VBN24T330BH000 7.9

2 2.00 50 63.5 55.0 0 60 4.0 60 4.0 - - 51-145 3.5-10 80 1/4 810VBN32T330BH000 9.22-1/2 2.56 65 107.4 93.0 0 75 5.0 75 5.0 - - 45-145 3.1-10 125 1/4 810VBN40T350BH000 * 18.5

3 3.15 80 132.8 115.0 0 50 3.5 50 3.5 - - 45-145 3.1-10 125 1/4 810VBN48T350BH000 * 23.1

316L STAINLESS STEEL VALVESPort Orifice Size Valve Number Wt. Size DN Cv Kv Min psi bar psi bar psi bar psi bar mm port Stainless (1) (2) (3) (4) lbs

inch (mm) (m3/h) dia bsp1/2 0.59 15 4.1 3.6 0 320 22.0 320 22.0 - - 51-145 3.5-10 50 1/8 810VSN08T320BH000 2.43/4 0.78 20 9.2 8.0 0 190 13.0 190 13.0 - - 65-145 4.5-10 50 1/8 810VSN12T320BH000 2.61 1.00 25 17.3 15.0 0 85 5.8 85 5.8 - - 65-145 4.5-10 50 1/8 810VSN16T320BH000 3.1

1-1/4 1.25 32 24.3 21.0 0 75 5.2 75 5.2 - - 85-145 5.7-10 50 1/8 810VSN20T320BH000 4.01-1/2 1.56 40 40.4 35.0 0 100 7.0 100 7.0 - - 51-145 3.5-10 80 1/4 810VSN24T330BH000 7.9

2 2.00 50 63.5 55.0 0 60 4.0 60 4.0 - - 51-145 3.5-10 80 1/4 810VSN32T330BH000 9.22-1/2 2.56 65 107.4 93.0 0 100 7.0 100 7.0 - - 45-145 3.1-10 125 1/4 810VSN40T350BH000 18.5

Pressure ratings reflect standard product offering. Higher pressure ratings are available. Consult Parker.

(1) Chrome Plated Brass Actuator Standard, Anodized Aluminum for 125mm housing(2) For BSP porting, change "N" to "G" in the 6th position(3) Optional Stainless Actuator, change "B" to "S" in the 13th position(4) For ultra-high temperature 430°F, 1/2" to 1-1/4"sizes only, see Ultra High Temperature tables* Brass Body

Pilot Pressure

Pilot Pressure

Flow Coeff

Flow Coeff

Operating Pressure

Operating Pressure

air, gases water, liquids steam

air, gases steam water, liquids

Actuator

Actuator


6

Series 810 Operating Data: Normally Closed, Flow Direction Over SeatRecommended for steam and most gases

0

100

200

300

400

500

600

0 15 30 45 60 75 90Pilot pressure [psi]

1"1 1/4"

1 1/2"

2"

3"

2 1/2"

TYPE 810-NC-with flow

3"

Upper limit for brass and bronze

0

100

200

300

400

500

600


1 1/4"

1 1/2"

2"2 1/2"

3"


5"


0

100

200

300

400

500

600



2"

1 1/2"

1 1/4"

3/4"

1"


2"1/2"

Control Pressure & Operating Pressure Charts

BRONZE / BRASS * BODY VALVESPort Orifice Size Valve Number Wt. Size DN Cv Kv Min psi bar psi bar psi bar psi bar mm port Bronze (1) (2) lbs

inch (mm) (m3/h) dia bsp1/2 0.59 15 4.1 3.6 0 232 16.0 - - 210 14.5 40-145 2.8-10 50 1/8 810VBN08T120BH000 2.43/4 0.78 20 9.2 8.0 0 232 16.0 - - 210 14.5 40-145 2.8-10 50 1/8 810VBN12T120BH000 2.61 1.00 25 17.3 15.0 0 232 16.0 - - 210 14.5 40-145 2.8-10 50 1/8 810VBN16T120BH000 3.1

1-1/4 1.25 32 24.3 21.0 0 75 5.2 - - 75 5.2 40-145 2.8-10 50 1/8 810VBN20T120BH000 4.01-1/2 1.56 40 40.4 35.0 0 232 16.0 - - 210 14.5 16-145 1.1-10 80 1/4 810VBN24T130BH000 7.9

2 2.00 50 63.5 55.0 0 203 14.0 - - 203 14.0 16-145 1.1-10 80 1/4 810VBN32T130BH000 9.22-1/2 2.56 65 107.4 93.0 0 175 12.1 - - 175 12.1 8-145 0.6-10 125 1/4 810VBN40T150BH000 * 18.5

3 3.15 80 132.8 115.0 0 131 9.0 - - 131 9.0 8-145 0.6-10 125 1/4 810VBN48T150BH000 * 23.1


inch (mm) (m3/h) dia bsp1/2 0.59 15 4.1 3.6 0 580 40.0 - - 210 14.5 40-145 2.8-10 50 1/8 810VSN08T120BH000 2.43/4 0.78 20 9.2 8.0 0 535 36.8 - - 210 14.5 40-145 2.8-10 50 1/8 810VSN12T120BH000 2.61 1.00 25 17.3 15.0 0 290 20.0 - - 210 14.5 40-145 2.8-10 50 1/8 810VSN16T120BH000 3.1

1-1/4 1.25 32 24.3 21.0 0 160 11.0 - - 160 11.0 40-145 2.8-10 50 1/8 810VSN20T120BH000 4.01-1/2 1.56 40 40.4 35.0 0 335 23.1 - - 210 14.5 16-145 1.1-10 80 1/4 810VSN24T130BH000 7.9

2 2.00 50 63.5 55.0 0 203 14.0 - - 203 14.0 16-145 1.1-10 80 1/4 810VSN32T130BH000 9.22-1/2 2.56 65 107.4 93.0 0 175 12.1 - - 175 12.1 8-145 0.6-10 125 1/4 810VSN40T150BH000 18.5



Pilot Pressure

Pilot Pressure

air, gases

Flow Coeff

Flow Coeff

Operating Pressure

Operating Pressure


water, liquids steam

Actuator

Actuator


7

BRONZE / BRASS * BODY VALVESPort Orifice Size Valve Number Wt. Size DN Cv Kv Min psi bar psi bar psi bar psi bar mm port Bronze (1) (2) lbs

inch (mm) (m3/h) dia bsp1/2 0.59 15 4.1 3.6 0 232 16.0 232 16.0 210 14.5 35-145 2.4-10 50 1/8 810VBN08T220BH000 2.43/4 0.78 20 9.2 8.0 0 232 16.0 232 16.0 210 14.5 45-145 3.1-10 50 1/8 810VBN12T220BH000 2.61 1.00 25 17.3 15.0 0 160 11.0 160 11.0 160 11.0 50-145 3.5-10 50 1/8 810VBN16T220BH000 3.1

1-1/4 1.25 32 24.3 21.0 0 100 7.0 100 7.0 100 7.0 50-145 3.5-10 50 1/8 810VBN20T220BH000 4.01-1/2 1.56 40 40.4 35.0 0 232 16.0 232 16.0 210 14.5 20-145 1.4-10 80 1/4 810VBN24T230BH000 7.9

2 2.00 50 63.5 55.0 0 190 13.0 190 13.0 190 13.0 20-145 1.4-10 80 1/4 810VBN32T230BH000 9.22-1/2 2.56 65 107.4 93.0 0 175 12.1 175 12.1 175 12.1 10-145 0.7-10 125 1/4 810VBN40T250BH000 * 18.5

3 3.15 80 132.8 115.0 0 131 9.0 131 9.0 131 9.0 10-145 0.7-10 125 1/4 810VBN48T250BH000 * 23.1


inch (mm) (m3/h) dia bsp1/2 0.59 15 4.1 3.6 0 580 40.0 580 40.0 210 14.5 35-145 2.4-10 50 1/8 810VSN08T220BH000 2.43/4 0.78 20 9.2 8.0 0 305 21.0 305 21.0 210 14.5 45-145 3.1-10 50 1/8 810VSN12T220BH000 2.61 1.00 25 17.3 15.0 0 160 11.0 160 11.0 160 11.0 50-145 3.5-10 50 1/8 810VSN16T220BH000 3.1

1-1/4 1.25 32 24.3 21.0 0 100 7.0 100 7.0 100 7.0 50-145 3.5-10 50 1/8 810VSN20T220BH000 4.01-1/2 1.56 40 40.4 35.0 0 305 21.0 305 21.0 210 14.5 20-145 1.4-10 80 1/4 810VSN24T230BH000 7.9

2 2.00 50 63.5 55.0 0 190 13.0 190 13.0 190 13.0 20-145 1.4-10 80 1/4 810VSN32T230BH000 9.22-1/2 2.56 65 107.4 93.0 0 175 12.1 175 12.1 175 12.1 10-145 0.7-10 125 1/4 810VSN40T250BH000 18.5



Pilot Pressure

Pilot Pressure

air, gases

Flow Coeff

Flow Coeff

steam

air, gases

Operating Pressure

Operating Pressure


water, liquids

Actuator

Actuator

Series 810 Operating Data: Normally Open, Flow Direction Under Seat


0

100

200

300

400

500

600


DN25

DN32

DN40

DN50

DN65

DN80

TYPE 810-NO-against flow

3"


0

100

200

300

400

500

600


1 1/4"

1 1/2"

2"2 1/2"

3"


5"


0

100

200

300

400

500

600


1"

3/4"

1/2"

1 1/4"

1 1/2"


2"


Series 810: 2 Way Angle Body Valves: 1/2” to 1 1/4” NPT

8

Series 810 Operating Data: Ultra High Temp., Normally Closed,Flow Direction Under Seat- For control of fluids up to 430° F / 221° C

Series 810 Operating Data: Ultra High Temp., Normally Closed,Flow Direction Over Seat- For control of fluids up to 430° F / 221° C

0

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0P ilo t p r e s s u re [p s i]

Wor

king

pre

ssur

e [p

si]

1 "1 1 /4 "

T Y P E 8 1 0 U H T -N C -c lo s in g w ith flo w

Actuator diameter 5”

0

100

200

300

400

500

600

0 10 20 30 40 50 60 70 80 90Pilot pressure [psi]

Wor

king

pre

ssur

e [p

si]

1/2"

3/4"

TYPE 810 UHT-NC-closing with flow



0

100

200

300

400

500

600

0 10 20 30 40 50 60 70 80 90Pilot pressure [psi]

Wor

king

pre

ssur

e [p

si]

1 1/4"

1"

TYPE 810 UHT-NC-closing with flow



inch (mm) (m3/h) dia bsp1/2 0.59 15 4.1 3.6 0 380 26.1 380 26.1 - - 85-145 5.8-10 50 1/8 810VSN08P320BU000 2.63/4 0.78 20 10.4 9.0 0 360 24.8 360 24.8 - - 51-145 3.5-10 80 1/8 810VSN12P330BU000 4.21 1.00 25 19.7 17.1 0 250 17.2 250 17.2 - - 51-145 3.5-10 80 1/4 810VSN16P330BU000 6.8

1-1/4 1.25 32 32.5 28.1 0 175 12.0 175 12.0 - - 80-145 5.5-10 80 1/4 810VSN20P330BU000 7.5

Pilot PressureFlow Coeff Operating Pressure


Actuator


inch (mm) (m3/h) dia bsp1/2 0.59 15 4.1 3.6 0 580 40.0 - - 330 22.7 65-145 4.5-10 50 1/8 810VSN08P120BU000 2.63/4 0.78 20 10.4 9.0 0 360 24.8 - - 330 22.7 65-145 4.5-10 50 1/8 810VSN12P120BU000 2.91 1.00 25 19.7 17.1 0 475 32.7 - - 330 22.7 51-145 3.5-10 80 1/4 810VSN16P130BU000 6.8

1-1/4 1.25 32 32.5 28.1 0 360 24.8 - - 330 22.7 51-145 3.5-10 80 1/4 810VSN20P130BU000 7.5Pressure ratings reflect standard product offering. Higher pressure ratings are available. Consult Parker.

(1) Chrome Plated Brass Actuator Standard, Anodized Aluminum for 125mm housing(2) For BSP porting, change "N" to "G" in the 6th position(3) Optional Stainless Actuator, change "B" to "S" in the 13th position(4) For ultra high temperature stainless valves, seal material changes from PTFE to PEEK.

Pilot PressureFlow Coeff

air, gases

Operating Pressure


Actuator


9

Series 810 Operating Data: Dimensions and Weights

Normally Closed Normally Open

A Actuator DN C D F G H I SW2Pipe Size Diameter

NPT mmBronze Brass Bronze Brass stroke Bronze Brass Bronze Brass lbs. Kg.

SST SST SST SST1/2" 50 15 2.55 - 0.45 2.45 5.30 - 4.70 G1/8 0.28 1.35 1.00 - 1.20 4.1 - 2.4 1.13/4" 50 20 2.95 - 0.50 2.45 5.30 - 4.90 G1/8 0.47 1.35 1.20 - 1.20 9.2 - 2.6 1.21" 50 25 3.55 - 0.60 2.45 5.70 - 5.10 G1/8 0.63 1.35 1.55 - 1.20 17.3 - 3.1 1.41" 80 25 3.55 - 0.60 3.80 7.30 - 9.70 G1/4 0.63 2.15 1.55 - 1.20 18.5 - 6.6 3.0

1-1/4" 50 32 4.35 - 0.65 2.45 6.30 - 5.70 G1/8 0.63 1.35 1.90 - 1.20 24.3 - 4.0 1.81-1/4" 80 32 4.35 - 0.65 3.80 7.85 - 7.50 G1/4 0.79 2.15 1.90 - 1.20 27.7 - 7.3 3.31-1/4" 125 32 4.35 - 0.65 5.75 9.05 - 8.45 G1/4 0.79 3.15 1.90 - 1.20 28.0 - 12.1 5.51-1/2" 50 40 4.70 - 0.75 2.45 6.50 - 5.90 G1/8 0.63 1.35 2.15 - 1.20 35.0 - 4.6 2.11-1/2" 80 40 4.70 - 0.75 3.80 8.05 - 7.70 G1/4 0.91 2.15 2.15 - 1.20 40.4 - 7.9 3.61-1/2" 125 40 4.70 - 0.75 5.75 9.25 - 8.65 G1/4 0.91 3.15 2.15 - 1.20 40.4 - 12.8 5.82" 50 50 5.90 - 0.85 2.45 7.30 - 6.30 G1/8 0.63 1.35 2.70 - 1.25 46.0 - 5.9 2.72" 80 50 5.90 - 0.85 3.80 8.85 - 7.85 G1/4 1.14 2.15 2.70 - 1.25 63.5 - 9.2 4.22" 125 50 5.90 - 0.85 5.75 9.85 - 8.85 G1/4 1.14 3.15 2.70 - 1.25 63.5 - 14.1 6.4

2-1/2" 80 65 - 7.10 1.00 3.80 - 10.25 8.25 G1/4 1.14 2.15 - 3.35 1.60 - 107 13.6 6.22-1/2" 125 65 - 7.10 1.00 5.75 - 11.20 9.45 G1/4 1.14 3.15 - 3.35 1.60 - 107 18.5 8.43" 80 80 - 8.25 1.10 3.80 - 11.00 8.8.5 G1/4 1.14 2.15 - 3.95 1.60 - 133 18.3 8.33" 125 80 - 8.25 1.10 5.75 - 12.00 9.85 G1/4 1.14 3.15 - 3.95 1.60 - 133 23.1 10.5

Dimension in inches except as noted

Cv-valuesB E SW1 Weight

Series 810: 2 Way Angle Body Valves: 1/2” to 1 1/4” NPT

10

Series 810 Operating Data: Dimensions and Weights- Ultra High Temp.

A Actuator DN B C D E F G H I SW1 SW2 Cv-Pipe Size Diameter values

NPT mmstroke lbs. Kg.

SST SST SST SST1/2" 50 15 2.55 0.45 2.45 5.70 5.95 G1/8 0.28 1.35 1.00 1.20 4.1 2.6 1.23/4" 50 20 2.95 0.50 2.45 6.00 6.25 G1/8 0.47 1.35 1.20 1.20 10.4 2.9 1.33/4" 80 20 2.95 0.50 3.80 7.30 7.75 G1/4 0.47 1.35 1.20 1.20 10.4 4.2 1.91" 80 25 3.55 0.60 3.80 7.60 8.08 G1/4 0.63 2.15 1.55 1.20 19.7 6.8 3.11" 125 25 3.55 0.60 5.75 8.80 9.23 G1/4 0.63 2.15 1.55 1.20 19.7 11.7 5.3

1-1/4" 80 32 4.35 0.65 3.80 8.30 8.85 G1/4 0.79 2.15 1.90 1.20 32.5 7.5 3.41-1/4" 125 32 4.35 0.65 5.75 9.50 10.05 G1/4 0.79 3.15 1.90 1.20 32.5 12.3 5.6


Weight


11

Series 810 Typical Cross Section Drawing

Note: Parts marked with an arecontained in the spare parts kit. Whenordering spare parts kit, specify an “R” inthe 4th position of the complete Angle SeatValve Model Number.

Series 820: 2 Way Angle Body Control Valves: 1/2” to 2” NPT

12

DIGITAL CONTROL: Control valve with integratedmicroprocessor-positioner for neutral through aggressive fluids.Features:• Operates independent of supply pressure variations.• No steady state air consumption.• Contactless strike feedback (inductive sensor)• Not sensitive to vibration• Instrument grade air not essential• Individually programmable software configurable flow characteristics• Protection Class IP 65• For pneumatic control with linear or rotary actuators

Technical SpecificationsB o d y M a te r ia l A I S I 3 1 6 L

F u n c t io n 2 /2 N o r m a l ly C lo s e d , C lo s e s a g a in s t t h e f lo w

N o m in a l s iz e s 1 /2 " - 2 "C o n n e c t io n s :N P T t h r e a d s t a n d a r dB S P t h r e a d ( I S O 2 2 8 / 1 ) 1 /2 " - 2 "S A ET u b e E n d sF la n g e s A N S I 1 5 0D if fe r e n t ia l P r e s s u r e S e e S p e c i f i c a t io n s t a b le sP i lo t P r e s s u r e u p t o 1 4 5 p s i ( 1 0 b a r ) r e fe r e n c e g r a p h sA c t u a to r : 3 " b r a s s p la t e d , 5 " a lu m in u m

^ O p t io n a l ^ 3 " S ta in le s s A c t u a t o rM a x . f lu id te m p e r a tu r e - 2 2 ° F ( - 3 0 ° C ) u p t o 3 9 2 ° F ( 2 0 0 ° C )

# O p t io n a l # t o - 4 0 ° F ( - 4 0 ° C )* O p t io n a l * U p to + 4 3 0 ° F ( 2 2 1 ° C )

S e a l M a t e r ia l P T F EP a c k in g G la n d P T F E / G r a p h it eV is c o s i ty o f th e f lu id m a x . 6 0 0 m m ² /s ( 6 0 0 c S t , 8 0 ° E , 2 7 0 0 S S U )V a c u u m m a x im u m 0 . 0 2 9 5 m e r c u r y ( H g )W o r k in g p r e s s u r e fo r m a x im u m 1 7 5 p s iin v e r t e d p a c k in g f o r v a c u u m s e r v ic eL e a k a g e A N S I C la s s V I s h u t o f fI n s t a l la t io n A n y p o s i t io nP i lo t C o n t r o l M e d ia A i r , n e u t r a l g a s , w a te r

F lu id s I n e r t g a s e s , h o t w a t e r , o i ls , s te a m , a g g r e s s iv e & c o r r o s iv e f lu id s

O p t ic a l P o s i t io n I n d ic a to r S ta n d a r d

Port Orifice Size Operating Pressure Valve Number Valve Number WtSize DN Cv Kv Min psi bar psi bar psi bar psi bar mm port Stainless (1) (2) (3) Stainless (1) (2) (3) lbs

inch mm (m3/h) dia bspLinear Flow

(4)(5)Equal Percentage Flow

(6)(7)1/2 0.59 15 4.4 3.8 0 232 16.0 232 16.0 225 15.5 58-87 4-6 80 1/4 820VSN08TD3ABH000 820VSN08TD3EBH000 9.03/4 0.78 20 10.2 8.9 0 232 16.0 232 16.0 225 15.5 58-87 4-6 80 1/4 820VSN12TD3ABH000 820VSN12TD3EBH000 9.31 1.00 25 16.2 14.1 0 232 16.0 232 16.0 225 15.5 58-87 4-6 80 1/4 820VSN16TD3ABH000 820VSN16TD3EBH000 9.7

1-1/4 1.25 32 23.2 20.2 0 145 10.0 145 10.0 145 10.0 58-87 4-6 80 1/4 820VSN20TD3ABH000 820VSN20TD3EBH000 10.41-1/4 1.25 32 23.2 20.2 0 232 16.0 232 16.0 225 15.5 44-87 3-6 125 1/4 820VSN20TD5ABH000 820VSN20TD5EBH000 16.11-1/2 1.56 40 31.3 27.2 0 87 6.0 87 6.0 87 6.0 58-87 4-6 80 1/4 820VSN24TD3ABH000 820VSN24TD3EBH000 11.01-1/2 1.56 40 31.3 27.2 0 232 16.0 232 16.0 225 15.5 58-87 4-6 125 1/4 820VSN24TD5ABH000 820VSN24TD5EBH000 16.8

2 2.00 50 42.9 37.3 0 45 3.0 45 3.0 45 3.0 58-87 4-6 80 1/4 820VSN32TD3ABH000 820VSN32TD3EBH000 12.42 2.00 50 42.9 37.3 0 131 9.0 131 9.0 131 9.0 58-87 4-6 125 1/4 820VSN32TD5ABH000 820VSN32TD5EBH000 18.1

(1) Chrome Plated Brass Actuator Standard, Anodized Aluminum for 125mm housing(3) For BSP porting, change "N" to "G" in the 6th position(3) Optional Stainless Actuator, change "B" to "S" in the 13th position(4) For 40% linear reduced flow, change 12th position to "B" from A(5) For 25% linear reduced flow, change 12th position to "C" from A(6) For 40% equal percentage reduced flow, change 12th position to "F" from E(7) For 25% equal percentage reduced flow, change 12th position to "G" from E

Actuator


Pilot PressureFlow Coeff

air, gases


13

ELECTRO-PNEUMATIC CONTROL: Electro-Pneumaticallyoperated control valve for neutral to aggressive fluids includingelectro-pneumatic (e/p) positioner.Features:• Integrated Positioner• All parts contacting fluid made of 316L Stainless Steel• Temperatures up to 392° F / 200° C• Compact Design


F u n c t io n 2 / 2 N o r m a l ly C lo s e d , C lo s e s a g a in s t t h e f lo w

N o m in a l s iz e s 1 / 2 " - 2 "C o n n e c t io n s :N P T th r e a d s t a n d a r dB S P t h r e a d ( I S O 2 2 8 /1 ) 1 / 2 " - 2 "S A ET u b e E n d sF la n g e s A N S I 1 5 0D if fe r e n t ia l P r e s s u r e S e e S p e c i f ic a t io n s t a b le sP i lo t P r e s s u r e u p to 1 4 5 p s i ( 1 0 b a r ) r e f e r e n c e g r a p h sA c t u a to r : 3 " b r a s s p la te d , 5 " a lu m in u m

^ O p t io n a l ^ 3 " S t a in le s s A c t u a t o rM a x . f lu id te m p e r a tu r e - 2 2 ° F ( - 3 0 ° C ) u p t o 3 9 2 ° F ( 2 0 0 ° C )


S e a l M a t e r ia l P T F EP a c k in g G la n d P T F E / G r a p h it eV is c o s i ty o f th e f lu id m a x .6 0 0 m m ² / s ( 6 0 0 c S t , 8 0 ° E , 2 7 0 0 S S U )V a c u u m m a x im u m 0 . 0 2 9 5 m e r c u r y ( H g )W o r k in g p r e s s u r e f o r m a x im u m 1 7 5 p s iin v e r t e d p a c k in g f o r v a c u u m s e r v ic eL e a k a g e A N S I C la s s V I s h u t o f fI n s ta l la t io n A n y p o s i t io nP i lo t C o n t r o l M e d ia A ir , n e u t r a l g a s , w a te r

F lu id s In e r t g a s e s , h o t w a te r , o i ls , s te a m , a g g r e s s iv e & c o r r o s iv e f lu id s

O p t ic a l P o s i t io n I n d ic a t o r S ta n d a r d




(6)(7)1/2 0.59 15 4.4 3.8 0 232 16.0 232 16.0 225 15.5 60-90 4.1-6.2 80 1/4 820VSN08T83ABH000 820VSN08T83EBH000 8.83/4 0.78 20 10.2 8.9 0 232 16.0 232 16.0 225 15.5 60-90 4.1-6.2 80 1/4 820VSN12T83ABH000 820VSN12T83EBH000 9.01 1.00 25 16.2 14.1 0 175 12.1 175 12.1 175 12.1 60-90 4.1-6.2 80 1/4 820VSN16T83ABH000 820VSN16T83EBH000 9.5

1-1/4 1.25 32 23.2 20.2 0 102 7.0 102 7.0 102 7.0 60-90 4.1-6.2 80 1/4 820VSN20T83ABH000 820VSN20T83EBH000 10.11-1/4 1.25 32 23.2 20.2 0 190 13.1 190 13.1 190 13.1 45-90 3.1-6.2 125 1/4 820VSN20T85ABH000 820VSN20T85EBH000 15.81-1/2 1.56 40 31.3 27.2 0 60 4.1 60 4.1 60 4.1 60-90 4.1-6.2 80 1/4 820VSN24T83ABH000 820VSN24T83EBH000 10.81-1/2 1.56 40 31.3 27.2 0 160 11.0 160 11.0 160 11.0 60-90 4.1-6.2 125 1/4 820VSN24T85ABH000 820VSN24T85EBH000 16.5

2 2.00 50 42.9 37.3 0 85 5.9 85 5.9 85 5.9 60-90 4.1-6.2 125 1/4 820VSN32T85ABH000 820VSN32T85EBH000 17.8


ActuatorPilot PressureFlow Coeff



14

PNEUMATIC CONTROL: Pneumatically operated control valve forneutral to aggressive fluids including pneumatic (p/p) positioner.Features• Integrated Positioner• All parts contacting fluid made of 316L Stainless Steel• Temperatures up to 392° F / 200° C• Compact Design


F u n c t io n 2 / 2 N o r m a l ly C lo s e d , C lo s e s a g a in s t t h e f lo w

N o m in a l s iz e s 1 / 2 " - 2 "C o n n e c t io n s :N P T th r e a d s t a n d a r dB S P t h r e a d ( I S O 2 2 8 /1 ) 1 / 2 " - 2 "S A ET u b e E n d sF la n g e s A N S I 1 5 0D if fe r e n t ia l P r e s s u r e S e e S p e c i f ic a t io n s t a b le sP i lo t P r e s s u r e u p to 1 4 5 p s i ( 1 0 b a r ) r e f e r e n c e g r a p h sA c t u a to r : 3 " b r a s s p la te d , 5 " a lu m in u m

^ O p t io n a l ^ 3 " S t a in le s s A c t u a t o rM a x . f lu id te m p e r a tu r e - 2 2 ° F ( - 3 0 ° C ) u p t o 3 9 2 ° F ( 2 0 0 ° C )


S e a l M a t e r ia l P T F EP a c k in g G la n d P T F E / G r a p h it eV is c o s i ty o f th e f lu id m a x .6 0 0 m m ² / s ( 6 0 0 c S t , 8 0 ° E , 2 7 0 0 S S U )V a c u u m m a x im u m 0 . 0 2 9 5 m e r c u r y ( H g )W o r k in g p r e s s u r e f o r m a x im u m 1 7 5 p s iin v e r t e d p a c k in g f o r v a c u u m s e r v ic eL e a k a g e A N S I C la s s V I s h u t o f fI n s ta l la t io n A n y p o s i t io nP i lo t C o n t r o l M e d ia A ir , n e u t r a l g a s , w a te r

F lu id s In e r t g a s e s , h o t w a te r , o i ls , s te a m , a g g r e s s iv e & c o r r o s iv e f lu id s

O p t ic a l P o s i t io n I n d ic a t o r S ta n d a r d




(6)(7)1/2 0.59 15 4.4 3.8 0 232 16.0 232 16.0 225 15.5 60-90 4.1-6.2 80 1/4 820VSN08T63ABH000 820VSN08T63EBH000 8.13/4 0.78 20 10.2 8.9 0 232 16.0 232 16.0 225 15.5 60-90 4.1-6.2 80 1/4 820VSN12T63ABH000 820VSN12T63EBH000 8.41 1.00 25 16.2 14.1 0 175 12.1 175 12.1 175 12.1 60-90 4.1-6.2 80 1/4 820VSN16T63ABH000 820VSN16T63EBH000 8.8

1-1/4 1.25 32 23.2 20.2 0 102 7.0 102 7.0 102 7.0 60-90 4.1-6.2 80 1/4 820VSN20T63ABH000 820VSN20T63EBH000 9.51-1/4 1.25 32 23.2 20.2 0 190 13.1 190 13.1 190 13.1 45-90 3.1-6.2 125 1/4 820VSN20T65ABH000 820VSN20T65EBH000 15.21-1/2 1.56 40 31.3 27.2 0 60 4.1 60 4.1 60 4.1 60-90 4.1-6.2 80 1/4 820VSN24T63ABH000 820VSN24T63EBH000 10.11-1/2 1.56 40 31.3 27.2 0 160 11.0 160 11.0 160 11.0 60-90 4.1-6.2 125 1/4 820VSN24T65ABH000 820VSN24T65EBH000 15.8

2 2.00 50 42.9 37.3 0 85 5.9 85 5.9 85 5.9 60-90 4.1-6.2 125 1/4 820VSN32T65ABH000 820VSN32T65EBH000 17.2


ActuatorPilot Pressure


Flow Coeff


15

Cv - Values

DN 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"100% 4.4 10.2 16.2 23.2 31.3 42.9 3.5 7.0 11.6 18.6 29.0 -40% 1.7 4.1 6.7 9.3 12.8 - 1.4 2.8 4.6 7.0 11.6 -25% 1.1 2.6 4.2 - - - 0.9 1.7 3.0 - - -

Kv - Values

DN 15 20 25 32 40 50 15 20 25 32 40 50100% 3.8 8.8 14.0 20.0 27.0 37.0 3.0 6.0 10.0 16.0 25.0 -40% 1.5 3.5 5.8 8.0 11.0 - 1.2 2.4 4.0 6.0 10.0 -25% 0.9 2.2 3.6 - - - 0.8 1.5 2.6 - - -

Linear Equal Percentage

Linear Equal Percentage

Percentage Flow characteristic with reduced flows based on contour of sealing plug.


16

Series 820 Technical Data: Positioners

Electro-Pneumatic Positioner Pneumatic Positioner

Digital Positioner

(e/p) (p/p)

(i/p)


17

Series 820 Technical Data: Dimensions and Weights

A Actuator DN B C D I SW1 SW2Pipe Size Diameter

NPT mmSST p/p I/p digital p/p I/p digital SST p/p I/p digital

1/2" 80 15 2.55 0.60 3.80 8.65 9.85 11.80 9.05 10.25 11..4 3.15 1.00 1.20 8.1 8.8 9.03/4" 80 20 2.95 0.65 3.80 8.85 10.05 12.00 9.25 10.45 11.60 3.15 1.20 1.20 8.4 9.0 9.21" 80 25 3.55 0.75 3.80 9.25 10.45 12.40 9.45 10.65 11.80 3.15 1.55 1.20 8.8 9.5 9.7

1-1/4" 80 32 4.35 0.85 3.80 9.85 11.00 13.00 10.05 11.20 12.40 3.15 1.90 1.20 9.5 10.1 10.31-1/4" 125 32 4.35 0.85 5.75 10.45 11.60 14.15 10.85 12.00 13.60 4.15 1.90 1.20 15.2 15.8 16.11-1/2" 80 40 4.70 0.85 3.80 10.05 11.20 13.20 10.25 11.40 12.60 3.15 2.15 1.20 10.1 10.8 11.01-1/2" 125 40 4.70 0.85 5.75 10.65 11.8. 14.35 11.00 12.20 13.80 4.15 2.15 1.20 15.8 16.5 16.7

2" 80 50 5.90 0.85 3.80 10.85 12.00 13.80 10.65 11.80 13.00 3.15 2.70 1.25 11..7 12.1 12.32" 125 50 5.90 1.00 5.75 11.20 12.40 14.95 11.20 12.40 14.15 4.15 2.70 1.25 17.2 17.8 17.8


Positioner PositionerF Weight (lbs)E

810 and 820 Numbering System

18

Series 820 Valve Ordering1. Series 2 Configuration 3. Body Material 4 Connection Type 5. Port / Orifice 6. Seal Material 7 Pilot Function

Inches / DN810 V Valve Assembly B Bronze & Brass N NPT-thread 08 1/2" DN15 T PTFE For 810 Valve Series820 A Actuator Unit less Body S Stainless steel 316L G BSP- ISO 12 3/4" DN20 1 NC (closing with flow - over

seat)R Repair Kit J SAE 16 1" DN25 P PEEK 2 NO (closing against flow -

under seat)C ANSI Flanges 150 20 1-1/4" DN32 3 NC (closing against flow -

under seat)24 1-1/2" DN40 4 Universal, double acting

E Tube ends 32 2' DN50T Tri clamp inch (ASME

1998)40 2-1/2" DN65 Consult factory for other seal

materialsFor 820 Valve Series

48 3" DN80 6 Pneumatic positioner7 Electro-pneumatic positioner

8 Electro-pneumatic positioner with clamp adapter

9 Electro-pneumatic positioner ex-proof (II 2 G Eex ib IIC T6)

A Integrated process controller type

D Integrated digital positioner type

8 Actuator Diameter

9. Springs 10. Actuator Head Material 11. Temperature Version 12 Packing 13 Accessories 14 Additional

2 Piston 2" (NPT) For 810 Valve Series B Brass Plated, Alum Anodized for 5" size

For 810 Valve Series 0 Standard - PTFE Graphite Filled

For 810 Valve Series For 810 Valve Series

3 Piston 3" (NPT) 0 Standard S Stainless Steel 316 (Option for stainless body valves only)

H High temperature standard (392°F / 200°C) (bronze, stainless steel)

2 Inverted packing for Vacuum Service only

0 No accessories 0 No additional accessories

5 Piston 5" (NPT) U Ultra High temperature (430°F stainless steel only)

1 Electrical position indicator with single switch

1 Pilot Valve .078 (DN2) 120/60, 110/50 DIN coil

9. Characterisitics & Flow Values

L Low Temperature (-40°F / -40°C)

2 Electrical position indicator with double switches


For 820 Valve Series 3 3 Pilot Valve .078 (DN2) 240/60, 220/50 DIN coil

(standard spring only) For 820 Valve Series 4 Manual overide (N.C.) 4 Pilot Valve .078 (DN2) 24VDC DIN coil

A Linear - Full flow H High temperature standard (392°F) (stainless steel)

5 Stroke limitation (N.C.) 5 Pilot Valve .078 (DN2) 12VDC DIN coil

B Linear - reduced 40% flow U Ultra High temperature (430°F stainless steel only)

6 Electrical position indicator compact

C Linear - reduced 25% flow L Low Temperature (-40°F -40°C)

7 Position indicator with 2 proximity switches

For 820 Valve Series

8 Position indicator with 1 proximity switch

0 No additional accessories

E Equal percentage - Full flow


F Equal percentage - reduced 40% flow

For 820 Valve Series 2 Pilot Valve .078 (DN2) 240/60, 220/50 DIN coil

G Equal percentage - reduced 25% flow

0 No accessories 3 Pilot Valve .078 (DN2) 24/60, 24/50 DIN coil

4 Pilot Valve .078 (DN2) 24VDC DIN coil

5 Pilot Valve .078 (DN2) 12VDC DIN coil

Control Valve Accessories

19

FEATURESDigital Control Positioner Top Mounted

Compact construction for linear and rotary actuators

Control input 0/4-20mA, 0/2-10VDC

Inductive sensor for non-contact stroke feedback

140 movements per inch stroke for precise control, repeatable within <0.5%

Self calibrating

Flow characteristics programmable by PC software

Standard visual position indicator between the positioner and valve actuator

Alarm output capable

Available with stainless steel casing

Simple installation and serviceability


Set Point Signal 0/4 - 20 mA, 0/2 - 10 V, LON-fieldbus connection (optional)

Supply Voltage 24 VDC, maximum 10wSupply Pressure 44 - 87 psi / 3 - 6 barHysteresis < 0.5 %

Characteristics linear, equal percentage, user-defined, process optimized*

Adjustment (stroke, zero point) Self - LearningAmbient Temperature 14°F to 170°F / -10°C to + 76°CProtection class, DIN40050 IP 65

Range of Stroke / Angle 0.12…0.87 inches; 0.35…1.97 inches Rotary actuators up to 180°

Mounting to Control Valve Standard mountingAdaption to Range and Zero Self - LearningConfiguration Software configurable flow characteristicsSteady State Air Consumption None* Process optimized produces a linear flow characteristic for optimal control. After entering a few process points (e.g. upstream and downstream pressures), the optimized flow characteristic is calculated by the digital positioner configuration software and stored in the positioner memory.


20

FEATURESElectro-Pneumatic Positioner

Top Mounted

Compact construction

Control input 0/4-20mA, 0/2-10VDC

Standard visual position indicator between the positionerand valve actuator

Economical

Wide span range for easy adjustment

Available in intrinsically safe version



Input Signal Range pneumatic: 3-15 psi / 0.2 - 1 bar, electro-pneumatic: 0/4 - 20mA

Stroke Range 0.2 - 1 inch depending on return springSupply Pressure 44 - 87 psi / 3 - 6 barSensitivity of Response <0.15 %Hysteresis < -1% to + 1%Characteristics linear, equal percentageAdjustment (stroke, zero point) mechanicalAmbient Temperature 14°F to 140°F / -10°C to + 60°CProtection class, DIN40050 IP 54

Air Consumption 13.3 to 21.3 scfh (depending on output pressure) II 2 G EEx ib IIC T6 +45°C / +113°F II 2 G EEx ib IIC T5 +60°C / +140°F

Housing Aluminum, black epoxy coated

Intrinsically Safe (optional)


21

FEATURESPneumatic Positioner

Top Mounted

Compact construction

Standard visual position indicator between the positionerand valve actuator

Economical

Easy adjustment


Technical SpecificationsInput Signal Range pneumatic: 3-15 psi / 0.2 - 1 barStroke Range 0.2 - 1 inch depending on return springSupply Pressure 44 - 87 psi / 3 - 6 barSensitivity of Response <0.15 %Hysteresis < -1% to + 1%Characteristics linear, equal percentageAdjustment (stroke, zero point) mechanicalAmbient Temperature 14°F to 140°F / -10°C to + 60°C

Air Consumption 13.3 to 21.3 scfh (depending on output pressure)

Housing Brass, chrome plated

3 Way Direct Acting Pilot Control Valves

22

FEATURES

Technical SpecificationsFunction 3/2 Normally Closed, Normally Open

and Multi-PurposeConnections:NPT thread standard 1/8" - 1/4 "

Differential Pressure See Specifications tablesPilot Control Media Air, neutral gas, waterMax. fluid temperature -20°F (-23°C) up to 185°F (85°C)Ambient temperature -20°F (-23°C) up to +140°F (60°C)Viscosity of the fluid max.22 mm²/s (22cSt, 3°E, 100SSU)Installation Any positionManual Locking Control Optional

Materials

Body Brass (stainless optional) Sleeve Stainless Core Stainless Spring Stainless Seals FKM

Coils DIN coil standardConduit & Hazardous coils optional

* *


Pilot Control ValveCompact design for industrial applicationsBrass or stainless steel body valvesNC (normally closed) and NO (normally open) versionsRugged coil family for all application demandsManual operation optional

port orifice size air water oil AC VALVE NUMBERS air water oil DC VALVE NUMBERSsize inch mm Cv Kv psi psi psi psi psi psi

(m3/h)

BRASS UNIVERSAL VALVE FOR NORMALLY CLOSED & NORMALLY OPEN REQUIREMENTS1/8 1/16 1.5 0.11 0.10 150 150 150 7133KBN1GVJ1N0D4D1xx 150 150 150 7133KBN1GVJ1N0D5D1xx1/8 5/64 2.0 0.17 0.15 100 100 100 7133KBN1JVJ1N0D4D1xx 100 100 100 7133KBN1JVJ1N0D5D1xx

1/4 1/16 1.5 0.11 0.10 150 150 150 7133KBN2GVJ1N0D4D1xx 150 150 150 7133KBN2GVJ1N0D5D1xx1/4 5/64 2.0 0.17 0.15 100 100 100 7133KBN2JVJ1N0D4D1xx 100 100 100 7133KBN2JVJ1N0D5D1xx

STAINLESS NORMALLY CLOSED1/8 1/16 1.5 0.10 0.09 200 200 200 71315SN1GV00N0D4D1xx 200 200 200 71315SN1GV00N0D5D1xx

1/4 3/32 2.4 0.17 0.15 125 125 125 71315SN2KV00N0D4D1xx 125 125 125 71315SN2KV00N0D5D1xx

STAINLESS NORMALLY OPEN1/8 1/16 1.5 0.10 0.09 150 150 150 71395SN1GVJ1N0D4D1xx 150 150 150 71395SN1GVJ1N0D5D1xx

1/4 3/32 2.4 0.17 0.15 125 125 125 71395SN2KVJ1N0D4D1xx 125 125 125 71395SN2KVJ1N0D5D1xx

1 bar = 14.5 psi AC VoltageCodes DC VoltageCodesP3 = 120/60; 110/50 C1 = 12VDCQ3 = 240/60; 220/50 C2 = 24VDC

* xx - Replace with voltage code B2 = 24/60; 24/50

Flow Coef


23

ELECTRICAL SELECTION GUIDEAll Parker solenoid valves for pneumatic actuator control use standard coil designs that areinterchangeable. They are available in a wide variety of standard voltages and frequencies.Coils are labeled with electrical data providing easy identification.

Construction

Encapsulated waterproof coils are standard on all pilot valves. Numerous construction options areavailable including DIN terminals and conduit hub housing coils. The special compound is absolutelywaterproof and impervious to oil, dust and most corrosive fumes and vapors.

All coils are Class “F” rated for high temperature application requirements. Class H coils is optional.The coils are molded in accordance with UL, NEMA, and other accepted standards.

Coil Code* Class Wattage Description

D4D1xx F 13 DIN AC Voltages(terminations per DIN 43650 / ISO 4400 requirements)

D5D1xx F 16 DIN DC Voltages(terminations per DIN 43650 / ISO 4400 requirements)

C111xx F 10 Conduit, NEMA 4X 18” lead length, 2-wires

H111xx F 10 Hazardous, NEMA 4X, 7, 9 18” lead length, 2-wires

DIN coils are provided standard as noted in order table.To select the either conduit version coil, simply specify the coil number and voltage inpositions 15 through 20 of the valve number.

Example: To order 1/4” NPT brass body NC valve with NEMA 4 conduit coil rated for 120/60 voltage:7133KBN2JVJ1+N0+C111P3 = 7133KBN2JVJ1N0C111P3To order the pressure vessel alone, select only the pressure vessel number, the first 12 digits of thepart number.To select coil alone, select the 4-digit coil part and 2-digit voltage code.

Electrical Supply Requirements

The solenoid coil must be connected to electrical lines of correct voltage and frequency as indicated onthe coil label. The supply circuits must be properly sized to give adequate voltage at the coil leadseven when other electrical equipment is operating. The molded coil is designed to operate with linevoltage from 85% to 110% of the coil rated voltage. Operating with a line voltage above or below theselimits may result in reduced coil life or coil burn out. Also, operating with line voltage below the limit willresult in lowering the maximum operating pressure differential (MOPD).

Conversion from AC to DC Coils

The same valve assembly can be used for both AC and DC service requirements. AC and DC coils areinterchangeable. To convert a valve assembly from AC to DC service, select the appropriate DC coilvoltage per the valve specification chart based on the system pressure requirements.

* xx- Replace with voltage code


24

ELECTRICAL DATATo determine the approximate Holding or Inrush Current for AC voltages including 24/60, 120/60,208/60 and 240/60 in amperes, divide the voltage into the VA rating indicated in the AC PowerConsumption tables. DC valves have no inrush current. The current rating in amperes are shown inthe DC table. Figures are based on nominal values and will vary slightly depending on operatingvoltage and coil tolerances.

Valve Series AC Power Consumption Ratings DC Current Consumption Ratings (Amperes)

10 watt AC coils 10 watt DC coils

VA Holding VA Inrush 12VDC 24VDC

7133K 17 31 0.81 0.41

71315 16 30 0.81 0.41

71395 17 27 0.81 0.41

Technical Information

25

OPERATING PRINCIPLESIntroductionAngle seat valves are robust, high flow valvessuitable for many diverse industrial applicationsincluding chemical industry, food processing,steam sterilizers, water technology and OEMindustrial applications just to name a few. Thissection provides a brief overview of thecomponents and functional varieties of angleseat valves.

General Information

On-Off Valve Construction and BasicOperation

An angle seat valve is a piston operatedpneumatic device controlled by an externalpneumatic source, either gas or liquid. The angleseat valve is used to control the flow of liquids orgases in a positive, fully-closed or fully-openmode. The valve is commonly used in high flowrequirements, high temperature, aggressiveapplications and handling fluids with suspendedparticles, which replaced manual valves orelectrically / motorized operated valves.

The angle seat valve is operated by opening andclosing an orifice in a valve body which permits orprevents flow through the valve. The orifice isopened or closed through the use of a combinedstem, spring and piston assembly that is raised orlowered when a pneumatic source is applied tothe actuator head. The bottom of the stemcontains a compatible sealing material, whichcloses off the orifice in the body, stopping flowthrough the valve.

Proportional Control Valve Construction and Basic Operation

Proportional control valves are suitable for applications requiring pressure, temperature, flow and levelcontrol, generally recommend for closed loop systems but suitable for open loop systems as well. Thecontrol valve is generally the final element in the control circuit. The position of the valve stem iscontrolled through a control signal and feedback loop to maintain the system parameters. The controlsignal can be a pneumatic, voltage or current signal. The feedback loop, through sensors,transducers, meters, etc., adjust the control signal to match the required output. Various configurationsof the valve disc can better match the process flow rates over the entire flow range for consistent valvegain and stable process performance.


26

Proportional Control Valve Construction andBasicThe control valve series is available with integratedpositioners including digital, electro-pneumatic andpneumatic capabilities. The positioner senses thevalve stem position in comparison to an input signaland adjusts the actuation pressure and disc positionfor the required performance. The positioner istypically used in conjunction with a control valve toprovide better control and repeatability as well as tocombat hysteresis and other elements such aspacking friction.

LINEAR FLOW CHARACTERISTIC:Equal changes in flow for equal increments of lift,assuming a constant differential pressure acrossthe valve seat.

EQUAL PERCENTAGE FLOWCHARACTERISTIC:Equal changes in travel will produce equalpercentage changes in flow, assuming a constantdifferential pressure across the valve seat.

The flowing chart depicts typical results with varyingflow characteristic curves at constant pressuredifferentials.


27

DESIGN TERMINOLOGYContinuous Duty – A rating given to a valve that can be energized continuously with overheating.

Correction Factor – A mathematical relationship related to a fluids specific gravity used to convert specific flowsfrom a standard media to the media in question.

Current drain – The amount of current (expressed in amperes) that flows through the coil of a solenoid valvewhen it is energized.

Cv Factor- A mathematical factor that represents the quantity of water, in gallons per minute, that will passthrough a valve with a 1 psi pressure drop across the valve. The higher the Cv, the greater the flow through thevalve.

Fail Safe – The position of the valve upon loss of control signal or power.

Flow – Movement of fluid created by a pressure differential.

Flow Capacity – The quantity of fluid that will pass through a valve under a given set of temperature andpressure conditions.

I/P – A transducer used in control valves which converts an electronic instrument signal (generally 4-20ma) intoa pneumatic signal (generally 3-15 psi) which can be used to throttle a pneumatic control valve.

Manual Stem – A mechanical device that permits the manual opening or closing of a valve in the case ofemergency or power failure. A manual stem is available on all normally closed valves.

Maximum Operating Pressure Differential (MOPD) – The maximum pressure difference between the inlet andoutlet pressures of the valve must not exceeded, allowing the solenoid to operate in both the energized and de-energized positions.

Minimum Operating Pressure Differential – The minimum pressure difference between the inlet and outletpressures required for proper operation. This minimum operating pressure differential must be maintainedthroughout the operating cycle of pilot operated valves to assure proper shifting from the closed position to theopen position and visa versa. In the absence of the minimum operating pressure, the valve may close or will notfully open.

Orifice – The main opening through which fluid flows.

Safe Working Pressure -The maximum pressure a valve may be exposed to without experiencing any damage.The valve does not have to be operable at this pressure, but merely withstand the pressure without damage.

Linear Shut -off Catergories:ANSI Class III – Leakage must not exceed 0.1% of the total valve capacity.ANSI Class IV – Leakage must not exceed 0.01% of the total valve capacity.ANSI Class VI – Zero leakage rate achieve with a soft seal.

Metal seat-to-seat control valves typically exhibit ANSI class III and IV ratings.All Parker Hannifin angle valves meet ANSI class VI rating.

Offer Of SaleThe items described in this document are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and itsauthorized distributors. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’sorder for any item described in its document, when communicated to Parker Hannifin Corporation, its subsidiary or an authorized distributor (“Seller’]verbally or in writing, shall constitute acceptance of this offer.

1. Terms and Conditions of Sale: All descriptions, quotations, proposals, offers, acknowledgments, acceptances and sales of Seller’s products aresubject to and shall be governed exclusively by the terms and conditions stated herein. Buyer’s acceptance of any offer to sell is limited to these termsand conditions. Any terms or conditions in addition to, or inconsistent with those stated herein, proposed by Buyer in any acceptance of an offer bySeller, are hereby objected to No such additional, different or inconsistent terms and conditions shall become part of the contract between Buyer andSeller unless expressly ac-cepted in writing by Seller. Seller’s acceptance of any offer to purchase by Buyer is expressly conditional upon Buyer’s assentto all the terms and conditions stated herein, including any terms in addition to, or inconsistent with those contained in Buyer’s offer. Acceptance ofSeller’s products shall in all events constitute such assent.

2. Payment: Payment shall be made by Buyer net 30 days from the date of delivery of the items purchased hereunder. Any claims by Buyer foromissions or shortages in a shipment shall be waived unless Seller receives notice thereof within 30 days after Buyer’s receipt of the shipment. Theminimum order amount is $125.00 net, unless otherwise noted on the quotation .

3. Delivery: Unless otherwise provided on the face hereof, delivery shall be made F.O.B. Seller’s plant. Regardless of the method of delivery, however,risk of loss shall pass to Buyer upon Seller’s delivery to a carrier. Any delivery dates shown are approximate only and Seller shall have no liability for anydelays in delivery. Shipments are made by common carrier. Any premium freight must be requested and paid for by the Buyer.

4. Warranty: Seller warrants that the items sold hereunder shall be free from defects in material or workmanship for a period of 1 year from the date ofshipment to Buyer, or 2,000 hours of use, whichever expires first. THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAININGTO ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHER WARRANTY, GUARANTEE, OR REPRESENTA TION OF ANY KINDWHATSOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, MERCHANTIBILITY AND FITNESS FOR PURPOSE, WHETHEREXPRESS, IMPLIED, OR ARIS. ING BY OPERATION OF LAW, TRADE USAGE, OR COURSE OF DEAL ING ARE HEREBY DISCLAIMED.NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY ORPARTIALLY, TO BUYER’S DESIGNS OR SPECIFICATIONS.

5. Limitation Of Remedy: SELLER’S LIABILITY ARISING FROM OR IN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACTSHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE ITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAID BYBUYER, AT SELLER’S SOLE OPTION. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIALDAMAGES OF ANY KIND OR NATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAYCONNECTED WITH THIS AGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH OF CONTRACT,EXPRESS OR IMPLIED WARRANTY, OR IN TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO WARN OR STRICT LIABILITY.

6. Changes, Reschedules and Cancellations: Buyer may request to modify the designs or specifications for the items sold hereunder as well as thequantities and delivery dates thereof, or may request to cancel all or part of this order, however, no such requested modification or cancellation shallbecome part of the contract between Buyer and Seller unless accepted by Seller in a written amendment to this Agreement. Acceptance of any suchrequested modification or cancellation shall be at Seller’s discretion, and shall be upon such terms and conditions as Seller may require.

7. Special Tooling: A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired tomanufacture items sold pursuant to this contract. Such special tooling shall be and remain Seller’s property notwithstanding payment of any charges byBuyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the items sold hereunder, evenif such apparatus has been specially converted or adapted for such manufacture and notwithstanding any charges paid by Buyer. Unless otherwiseagreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time.

8. Buyer’s Property: Any designs, tools, patterns, materials, drawings, confidential information or equipment furnished by Buyer or any other items whichbecome Buyer’s property, may be considered obsolete and may be destroyed by Seller after two (2) consecutive years have elapsed without Buyerplacing an order for the items which are manufactured using such property. Seller shall not be responsible for any loss or damage to such property whileit is in Seller’s possession or control.

9. Taxes: Unless otherwise indicated on the face hereof, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxeswhich may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must be paid bySeller or if Seller is liable for the collection of such tax, the amount thereof shall be in addition to the amounts for the items sold. Buyer agrees to pay allsuch taxes or to reimburse Seller therefore upon receipt of its invoice. If Buyer claims exemption from any sales, use or other tax imposed by any taxingauthority, Buyer shall save Seller harmless from and against any such tax, together with any interest or penalties thereon which may be assessed if theitems are held to be taxable.

10. Indemnity For Infringement of Intellectual Property Rights: Seller shall have no liability for infringement of any patents, trademarks, copyrights, tradedress, trade secrets or similar rights except as provided in this Part 10. Seller will defend and indemnify Buyer against allegations of infringement of U.S.patents, U.S. trademarks, copyrights, trade dress and trade secrets (hereinafter ‘Intellectual Property Rights’). Seller will defend at its expense and willpay the cost of any settlement or damages awarded in an action brought against Buyer based on an allegation that an item sold pursuant to this contractinfringes the Intellectual Property Rights of a third party. Seller’s obligation to defend and indemnify Buyer is contingent on Buyer notifying Seller withinten (10) days after Buyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations oractions including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it infringes the Intellectual PropertyRights of a third party, Seller may, at its sole expense and option, procure for Buyer the right to continue using said item, replace or modify said item soas to make it noninfringing, or offer to accept return of said item and return the purchase price less a reasonable allowance for depreciation.Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to itemsdelivered hereunder for which the designs are specified in whole or part by Buyer, or infringements resulting from the modification, combination or use ina system of any item sold hereunder. The foregoing provisions of this Part 10 shall constitute Seller’s sole and exclusive liability and Buyer’s sole andexclusive remedy for infringement of Intellectual Property Rights.

If a claim is based on information provided by Buyer or if the design for an item delivered hereunder is specified in whole or in part by Buyer, Buyer shalldefend and indemnify Seller for all costs, expenses or judgments resulting from any claim that such item infringes any patent, trademark, copyright,trade dress, trade secret or any similar right.

11. Force Majeure: Seller does not assume the risk of and shall not be liable for delay or failure to perform any of Seller’s obligations by reason ofcircumstances beyond the reasonable control of Seller (hereinafter ‘events of Force Majeure]. Events of Force Majeure shall include without limitation,accidents, acts of God, strikes or labor disputes, acts, laws, rules or regulations of any government or government agency, fires, floods, delays orfailures in delivery of carriers or suppliers, shortages of materials and any other cause beyond Seller’s control.

12. Entire Agreement/Governing Law: The terms and conditions set forth herein, together with any amendments, modifications and any different termsor conditions expressly accepted by Seller in writing, shall constitute the entire Agreement concerning the items sold, and there are no oral or otherrepresentations or agreements which pertain thereto. This Agreement shall be governed in all respects by the law of the State of Ohio. No actionsarising out of the sale of the items sold hereunder or this Agreement may be brought by either party more than two (2) years after the cause of actionaccrues.

PD ABV 4100 4/04

Parker Hannifin CorporationClimate and Industrial Controls GroupFluid Control Division95 Edgewood AvenueNew Britain, CT 06051Phone: 860.827.2300visit us @ www.parker.com/fcd

CAT. ABV 0404

Documents

Angle Body Valves & Proportional Control Valves€¦ · Size DN Cv Kv Min psi bar psi bar psi bar psi bar mm port Bronze (1) (2) lbs inch (mm) (m 3 /h) dia bsp 1/2 0.59 15 4.1 3.6