Architectural Filter Ring Binder

Introduction

Tel: +44 (0)1264 366245 email: [email protected] www.leefilters.com

EXPERIENCE AND EXPERTISE IN FILM AND THEATRE LIGHTING HAS

ENABLED LEE FILTERS TO BRANCH OUT INTO DESIGNING AND MAKING

FILTERS FOR VARIOUS ARCHITECTURAL LIGHTING APPLICATIONS.

These include coloured sleeves forfluorescent lighting which are available inover 200 colours. These sleeves have beenused by architects and interior designers inshopping malls, restaurants, offices, clubsand hotel buildings around the world.

LEE also offer glass filters with a dichroiccoating for a range of different lightfittings, including MR16 and PAR16 bulbswhich are increasingly being used forambient lighting. Filters for these tinylamps, which provide a lot of heat as wellas light, have traditionally used strongcolours, which are often unsuitable forhomes and offices.

Our research team in conjunction withleading lighting designers have produced a whole range of glass dichroic filtersconsisting of very pale, subtle colours.These colours remove the harsh purewhites from a room, without giving astrong unwanted colour wash.

Introduction


To accompany our coloured glass filters wealso offer a range of glass diffusion filterswhich can be used to create a number ofdifferent lighting effects.

A range of accessories designed specifically for MR16 and PAR16 bulbs are alsoavailable. These include Screw-on andClip-on Filter Holders that enable filters tobe attached directly to a lamp. TheScrew-on holder can also hold a louvre.These louvres control the spill from thelamp, and therefore reduce glare.

LEE Filters are not merely designers andsuppliers of filters – a key area of ourbusiness is the expertise of our staff. Thisallows us to be true ‘solution providers’ toadvise and help you on many lighting andfiltration tasks and problems. We also takegreat pride in assisting with the productionof custom filters to meet the requirementsof specific applications. We can producecustom colours for both fluorescent sleevesand glass dichroic colours. Let us knowwhat we can do for you!

As the leading manufacturer of lightingfilter products we are able to provide acolour consistency from batch to batch thatis unmatched. Whether it’s a container loadof fluorescent sleeves you need or just afew glass filters, we endeavour to maintainample stock of the highest quality filters onthe market.

& Quick RollsFluorescent Sleeves


LEE FLUORESCENT SLEEVES CONSIST OF A CLEAR SLEEVE WITH

A COLOUR INSERT.

The sleeves are made from a thermallystable, electrically insulating polycarbonate,whilst the colour inserts are made from highquality LEE lighting filter.

With over 200 coloured inserts to choosefrom, the LEE range of fluorescent sleevesgives you more choice than ever for bothinterior and exterior lighting projects.Samples of all the colours available areshown in this binder.

The sleeves can be used on T5, T8 and T12tubes and are available in the followingstandard lengths 0.61m (2’), 1.22m (4’),1.53m (5’) and 2.44m (8’). Custom lengthsare also available on request.

It is recommended that you contact us ifintending to use sleeves on T5 tubes, asyour colour choice and tube wattage willdetermine if a sleeve is suitable. The sleevesare not recommended for use on highoutput T5 tubes, as the extreme heat ateither end of the tube can cause the filterto discolour.

The ends of each sleeve have a clear endcap; these caps fix the sleeve to thefluorescent tube and help with air flowaround the tube.

It is recommended that you always use thesupplied end caps, as without them thesleeve may come into direct contact withthe tube.

Due to the nature of the dyestuffs used,the coloured inserts inside the sleeve willfade over a period of time. This fading canbe reduced dramatically with the additionof a barrier in the form of a UV insert.These inserts can extend the life of a colour significantly.

When ordering fluorescent sleeves werecommend you contact LEE Filters todiscuss your exact requirements.

✘ ✔



Pre-assembled Sleeves

You choose the colour and leave the rest tous. Your chosen colour is inserted into thesleeve and delivered to you ready to install.

If you require a large number of sleevesof the same colour, rather than usingcolour inserts we will dye the polycarbonatesleeves for you.

This enables us to get the sleeves to you alot quicker. This service can be offered onorders of 1500 sleeves or more.

Self-assembly Sleeves

Alternatively you can assemble the insertand sleeve yourself. We supply the clearpolycarbonate sleeve and a Quick Roll ofyour chosen colour and you assemble themyourself. (See diagram on next page onhow to assemble)

THE SLEEVES CAN BE SUPPLIED IN TWO WAYS, PRE-ASSEMBLED

OR SELF ASSEMBLY.



Changing Colours with Quick Rolls

When a colour needs changing, you canreplace it easily using a Quick Roll. QuickRolls are rolls of filter pre-cut to the widthof either a T5, T8 or T12 sleeve. Each roll is7.62m (25’) long.

Once you have chosen your replacementcolour, simply unroll the length of thefluorescent sleeve required from the QuickRoll, cut it off the roll and re-insert it intoyour existing sleeve. It’s as easy as that!

T5 T8 T12

You require a clearsleeve, a Quick Rollof colour, two endcaps, a knife and arod / pole to stuffthe sleeve.

Stage 1Unwind the roll ofgel to the length ofthe sleeve.

Stage 2Cut the gel slightlylonger than thelength of the sleeve.

Stage 3Wrap the gel tightlyaround the rod / pole.

Stage 4Holding the gel tightlyaround the rod /polefeed it into one end ofthe sleeve, push therod / pole through thesleeve until it comesout the other end.

Stage 5Remove the rod /pole from the sleeve,leaving the gelinside the sleeve.

Stage 6Trim of any excessgel from the ends of the sleeve.

Stage 7Place end caps onboth ends of thesleeve.

How to Assemble a Coloured Fluorescent Sleeve



Get creative with fluorescent lighting!

There are a number of different ways you can use coloured fluorescent sleeves creatively. An effect that works particulay well is a two-tone sleeve. This is where you have one colourat the front of the sleeve and another contrasting colour at the back within the same sleeve.

Below are some examples of how two-tone sleeves can work.

Cyan – FrontMagenta – Back

Single Sleeves

Two Sleeves

Magenta – FrontCyan – Back

Magenta – Left SideCyan – Right Side

Left SleeveCyan Front / Magenta BackRight SleeveCyan Front / Magenta Back

Left SleeveCyan Front / Magenta BackRight SleeveMagenta Front / Cyan Back

Left SleeveMagenta Front / Cyan BackRight SleeveMagenta Front / Cyan Back

Left SleeveCyan Left / Magenta RightRight SleeveMagenta Left/ Cyan Right

Left SleeveMagenta Left / Cyan RightRight SleeveCyan Left / Magenta Right



No Filter Red

Amber Green

Blue Magenta

Coloured fluorescent sleeves can also beused to create different moods andatmospheres within a room. They workparticularly well in recessed fluorescentfittings where the tube can not be seen.

In the example below a recessedfluorescent tube positioned above afireplace has been coloured. Adding colourto the room creates a different atmosphereeach time.

The look of a room can be altered bysimply changing the colour insert inside thesleeve; allowing you to create a number ofdifferent looks quick and easily.



No Diffusion 1 2

3 4 5

6

Another effect that works well with coloured fluorescent sleeves is the addition of somediffusion in front of the sleeves. The diffusion softens the light giving a soft, subtle blendof colours.

In the example below a roll of LEE 216 White Diffusion was placed in front of threecoloured fluorescent sleeves. The distance between the diffusion and the sleeves wasthen slightly increased for each image, the further the distance the more diffused thecolours become.

colouredfluorescentsleeves

216 WhiteDiffusion

The distance between the diffusion andtubes determines the strength of thediffusion effect. The further apart thestronger the effect, the closer together theweaker the effect.



Ordering InformationWhen requesting a quotation or placing an order for fluorescent sleeves the followinginformation will be required:

Tube Diameter: T5, T8 or T12

Tube Length: 2’ (0.61m), 4’ (1.22m), 5’ (1.53m), 8’ (2.44m) or custom length.

Colour of Insert: Which colour do you require?

UV Insert: Do you require UV inserts?

Assembled or Self-assembly: Do you want the sleeves and inserts assembled by LEE Filters or do you wish to assemble them yourself?

Quantity: How many sleeves do you require?

To discuss specific requirements of a project, request a quotation or to place an orderplease contact LEE Filters on +44 (0) 1264 366245 or email [email protected]

FiltersGlass Dichroic


After a broad market survey the followingthemes emerged:

■ A selection of less saturated, subtlehues, as well as the usual “Rock andRoll” colours currently available.

■ Consistent colours.

■ A low cost way to select anddemonstrate colour choice to ownersand architects.

Once a colour palette was chosen thatincluded a selection of subtle less saturatedcolours, they were then produced as adichroic coating. This coating givesspectacularly clear and pure colours thatwill not fade and allows consistentrepeatable colours time and time again.

Samples of these colours can be found onthe following page*. Polyester samplesallow you to test colours on a project beforepurchasing the glass filters. Due to thedifferent nature of the two materials(dichroic glass v polyester), it is impossible toget an exact colour match, however usingour many years of experience you can besure they are the best match available. Thefull range of polyester samples are availablein a free swatch book 75mm x 95mm andlarger individual sample sheets of polyestercan also be purchased, contact LEE Filters forfurther details.

*If your binder contains glass samples then youwill see true representations of the colours.

BEFORE LAUNCHING THE LEE RANGE OF DICHROIC GLASS FILTERS,

RESEARCH WAS UNDERTAKEN WITH ARCHITECTURAL LIGHTING

DESIGNERS TO ESTABLISH THEIR THOUGHTS ON EXISTING PRODUCTS ON

THE MARKET AND WHAT IMPROVEMENTS COULD BE MADE TO THEM.

Filter SpecificationsGlass Dichroic

About our Dichroic Glass


LEE Filters’ Glass Dichroic filters aremanufactured by the vacuum deposition oflayers of thin metal films onto a substrateof borofloat glass. We use borofloat glassas it has better overall thermalcharacteristics than tempered soda-limeglass. The dichroic coating has beendesigned specifically to meet the demandsof the lighting industry and shouldwithstand temperatures up to 371°C. Theglass is available in two thicknesses, 1.7mmand 3.3mm.

Care should be taken when using the filtersin exterior applications. Any glass willeventually be damaged in environments ofextreme thermal shock.

Unframed Glass

Unframed glass dichroic filters are availablein a number of sizes. For outdoorapplications, a safety mesh is available asan option to help reduce damage fromthermal shock.

■ MR16 & PAR16 (49mm diameter) heldin stock.

■ Larger sizes and shapes are alsoavailable, please contact LEE Filters fora quotation.

Framed Glass

LEE Filters have developed frames for themost popular size lighting fixtures in theentertainment, architectural and theatricalindustries.

■ Source Four (15.8cm square)

■ Source Four PAR (19cm square)

■ PAR 64 (25.4cm square)

The lightweight aluminium frames have aninnovative silicone gasket that completelysurrounds the glass. For outdoor applications,a safety mesh is available as an option tohelp reduce damage from thermal shock.

Please note that the LEE Frame aperture for theSource Four PAR is slightly undersized and mayreduce light output in wide beam fixtures. Theframe design may also limit use with top hats orbarn doors, depending on the space allowed inthe colour frame slot.

Care and cleaning

Clean with a soft cloth or tissue and anon-abrasive cleaner. Do not submerge thefilter, and do not use cleaning productsthat will leave a residue. Dry the filtercompletely before reinstalling it.

While the coating can withstandtemperatures up to 371°C, the normaloperating temperature of borofloat glass is230°C and the extreme operatingtemperature is 490°C. Operating the glasscolour filter continuously at temperaturesexceeding 260°C may affect the life of thefilter, as the glass will become moresusceptible to damage from thermal shock.

Filter SpecificationsGlass Dichroic


Ordering InformationWhen requesting a quotation or placing an order for dichroic glass filters the following information willbe required:

Framed or Unframed: Do you require framed or unframed glass?

Thickness: Which thickness of glass do you require? 1.7mm or 3.3mm

Colour: Which colour do you require?

Size: Which size do you require? MR16, PAR16, Source Four, Source Four PAR,PAR 64 or custom.

Shape: Which shape do you require? Square, circular or custom.

Frosted: If you require a frosted dichroic filter, choose colours from the frosted dichroic range.

Quantity: How many filters do you require?

To discuss specific requirements of a project, request a quotation or to place an order pleasecontact LEE Filters on +44 (0) 1264 366245 or email [email protected]

FiltersGlass Diffusion

DESIGNED FOR MR16 AND PAR16

FITTINGS, THE LEE RANGE OF GLASS

DIFFUSION FILTERS OFFER A WIDE A

VARIETY OF LIGHTING EFFECTS AND

VARIOUS DIFFUSIONS.


The diagram below illustrates the effectscreated when using an 8°, 24° or 36° - 36wMR16 lamp at a distance of 3’.

Softening DiffusionLight diffusion.

Linear DiffusionMedium diffusion. Canbe used to sculpture alight beam eithervertically or horizontally.

Prismatic DiffusionMedium / strongdiffusion.

Frosted DiffusionStrong diffusion.

No Diffusion

Frosted Glass Diffusion

Dichroic FiltersSpecialised Glass

LEE SPECIALISED FILTERS ARE A RANGE OF FILTERS THAT INCLUDE

WARMING, COOLING AND UV FILTERS.


Cooling Filters

These filters will cool a light source. Theycan be used as cool blue colours or toconvert a tungsten light to daylight.

Full CT Blue

Half CT Blue

Quarter CT Blue

Wavelength Control Filters

UV Blocker Reduces photochemical degradation andallows the increase of light levels whilstreducing the risk of damage to displayobjects. Coated on a 3.3mm thick Borofloatglass substrate for high heat resistance, thisfilter blocks UV rays below 390nm.

Please note that tests should always becarried out to check the amount ofultra-violet rays being blocked by the filterbefore long term use.

Hot Mirror Filter (Infrared blocking) Blocks the heat generating IR componentof a light (wavelength above 750nm) whilesimultaneously transmitting the requiredvisible light with minimal loss.

Warming Filters

These filters warm up a cool light source.They can be used as warm amber colours orto reduce colour temperature.

Full CT Orange

Half CT Orange

Quarter CT Orange

*O80 Golden Amber 0 Warming filter.

*O80 Golden Amber 0 is also available in acombination 2 in 1 filter. As well as havingthe warming colour the filter also has alinear spread lens on one side. This lensallows the light beam to be spread eitherhorizontally or vertically.

O80 Golden Amber combination filter

AccessoriesFilter Holders &


Screw-on holder

Attach a filter directly onto a bulb usingthe LEE Filters accessory holder.

Suitable for the following bulbs:

■ MR16

■ PAR16

■ Compact Fluorescent (MR16)

Available in either black or silver, thescrew-on holder fits securely onto the bulb,and can hold up to two filters. This allowsfor a combination of colour, diffusion orlouvre effects to be used on the one fitting.

Louvres

Honeycomb louvres are available in eitherblack or silver to match the accessoryholder. Suitable for MR16 and PAR16fittings, the louvres help reduce the glarefrom the bulb, and are available in either45° or 60°.

The diagrams below show the glare freezones of both the 45° and 60° louvres.

Custom size louvres are also available;please contact LEE Filters for further details.

45º45º

Light Source

Louvre

Glare Free Zone Glare Free Zone

45º Louvre

60º60º

60º Louvre

Light Source

Louvre

Glare Free ZoneGlare Free Zone

AccessoriesFilter Holders &


Clip-on Accessories

LEE Clip-on accessories are a quick and easyway of adding a filter to or limiting theglare from MR16 and PAR16 bulbs.

Clip-on Filter Holder

The Clip-on Filter Holder holds a single1.7mm thick filter to a standard open bulb.The holder is available in either black orsilver (packs of five).

Clip-on Baffle

The Clip-on Baffle (also known as bladelouvres) traps the peripheral light sideways,limiting glare. The baffle also gives thefixture a more professional look. Availablein black or silver (packs of five).

Clip-on Barndoors

Clip-on Barndoors trap the light sideways,this limits the glare from a bulb but alsoallows you to direct the illumination fromthe bulb to a specific area. The flaps areadjustable by rotation and by bending thehinges. The high quality material of thehinges allows you to adjust them a numberof times. Available in black or silver (packsof five).

Documents

Architectural Filter Ring Binder