Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
BOQ for Financial Bid
NAME OF WORK : CONSTRUCTION OF THE BSVS, BUILDING (Ground + 2),
AT SHEOHAR, BLOCK SHEOHAR WARD NO.03, THANA NO. 163, KHATA NO. 2311, KHESARA NO. 2086 SHEOHAR-843329.
EMPLOYER
BANK OF BARODA
THE ASST. GENERAL MANAGER, BANK OF BARODA, REGIONAL OFFICE, MUZAFFARPUR REGION, PATNA ZONE,
Krishna Honda Building, 2nd floor, Akharaghat Road, Muzaffarpur-842001.
Tel- 0621-2224011 Email- [email protected]
ARCHITECT
YASHWANT KUMAR
Asha-9B Avenue South Park, Bistupur, Jamshedpur-831001.
Tel-0657-232091, 9431932201
SL No Description Unit Quantity Rate Amount
1 Earth Excavation :-Earth work in
excavation in foundation trenches (not
exceeding 1.5 m in width or 10 sqm on
plan) including dressing of sides and
ramming of bottoms, lift upto 1.5 m .
including getting out the excavated soil
and disposal of surplus excavated soil as
directed, within a lead of 50 m.
All Kinds of Soil Cum 1792.0
2 Ploughing the existing ground for tie beam
& fin to a depth ot 15 cm to 25 cm and
watering the same
All kinds of soil. sqm 39.0
3 Re felling of soil:- Filling available
excavated earth (excluding rock) in
trenches, plinth,of foundations etc. in
layers not exceeding 20 cm in depth:
consolidating each deposited layer by
ramming and watering lead.
cum 1728.0
4 Sand filling:- Supplying and Filling in
plinth 610mm & 50mm Th Sand filling in
footing trench and level with local sand
and under floors including, watering,
ramming consolidating and dressing
complete.
cum 143.0
5 Brick flat Soiling in Foundation :-
Providing designation 100 B one brick flat
soling in foundation trench & below tie
beam joints filled with local sand including
cost of watering, taxes, royalty all complete
as per building specification and direction
of E/l.
sqm 211.0
6 P.C.C In Foundation:- Providing and 1.4.8 (1 Cement :4 coarse sand :8 graded
stone aggregate 40 mm nominal size)
cum 11
B.O.Q FOR CIVIL ,ELECTRICAL & SANITATION WORK IN B.S.V.S AT SHEOHAR,
B.O.B,MUZAFFARPUR REGION
SUB HEAD A ( CIVIL WORK IN BUILDING) ,GROUND ,1St & 2nd FLOOR )
Section 1(Footing & Other work up to Plinth
7 Providing and laying in position machine
batched, machine mixed and machine
vibrated design mix cement concrete of
specified grade for reinforced cement
concrete structural elements, excluding the
cost of centring, shuttering finishing and
reinforcement, M-20 grade reinforced
cement concrete.
1:1:5:3(1 cement: 1.5 coarse sand:3
graded stone aggregate 20 mm nominal
size)
All work upto plinth level cum 76
Brick work
8 250mm Th Brick work with bricks of class
designation 100A above tie beam up to
plinth in :Cement mortar 1:6 (1 cement: 6 coarse
sand )cum 23
9 D.P.C :- Providing and laying damp-proof
Course 50 mm thick with cement concrete
1:2:4(1cement:2:2 coarse sand :4 graded
stone aggregate 20mm nominal size)sqm 23
10 Extra for providing and mixing water
prodding material in cement concrete work
in the proportion mixing cement concrete
in mixer with 5% Cisco or any other water
proffing compound as per building
specification and direction of E/I.Note-
Mixing water proofing material @1Kg/ bag
of cement.
per 50 kg
cement/1
bag
cement
@1Kg
cisco
5.5
11 Centring and shuttering:- Centring and
shuttering including strutting, propping etc.
up to plinth level and removal of form for.
Foundations, footings, bases of columns
etc. for mass concrete.sqm 39
Lintels, beams, plinth beams, girders,
ressumers and cantilevers.sqm 50
Columns, Pillars, Piers, Abutments, Posts
and Strutssqm 76
12 Reinforcement in footing,column & Tie
beam up to plinth LevelReinforcement for R.C.C. work including
straightening, cutting, bending, placing in
position and binding all complete.
Thermo-Mechanically Treated bars TMTC-
500-8mm dia.kg 21
Thermo-Mechanically Treated bars TMTC-
500-10mm dia.kg 362
R.C.C work in Footing , Tie beam & Column up to P.L
Thermo-Mechanically Treated bars TMTC-
500-12mm dia.kg 1709
Thermo-Mechanically Treated bars TMT
Fe-500-I6mrn dia.kg 192
Brick work
13 250mm Th Brick work with bricks of class
designation 100A above plinth up to 1St
Floor Level in :
Cement mortar 1:6 (1 cement: 6 coarse
sand )cum 64
14 125mm Th Half brick masonry with bricks
of class designation 100A above plinth
up to 1St floor Level in :
Cement mortar 1:4 (1 cement: 4 coarse
send)sqm 153
15 Extra for providing and placing in position
2 Nos, 6 mm dia , MS bars at every third
course of half brick masonry.sqm 153
16 Providing and laying in position machine
batched, machine mixed and machine
vibrated design mix cement concrete of
specified grade for reinforced cement
concrete structural elements, excluding the
cost of centring, shuttering finishing and
reinforcement, M-20 grade reinforced
cement concrete. 1:1:5:3(1 cement: 1.5
coarse sand:3 graded stone aggregate 20
mm nominal size)
All work above plinth level(Walls columns,
pillars, posts cind struts)cum 9.5
Beams, planth beams, girders,
bressumers, contilevers,Suspended floors
lintels roofs and staircases including spiral
staircases, shelves etc
cum 102
17 Centring & Shuttering :- Centring and
shuttering including strutting, propping
etc.above plinth up to floor level and
removal of form for.Suspended floors, roofs, landings,
balconies and access platform.sqm 256
Lintels beam,roof beams, and cantilevers.sqm 59
Columns, Pillars, Piers, Abutments, Posts
and Strutssqm 142
Stairs,(excluding landings) except spiral-
staircases.sqm 9.5
Total Section l :-
Section ll (Super structure at Ground floor above plinth Lev)
R.C.C work in Column ,Lintel beam & Chhaja ,Roof beam & roof Slab up
Chhaja ,Perdi, Vertical and horizontal fins
individually or forming box louvers band,
facias and eaves boardssqm 6
18 Reinforcement for R.C.C. work including
straightening, cutting, bending, placing in
position and binding all complete.
Thermo-Mechanically Treated bars TMTC-
500-8mm dia.kg 1462
Thermo-Mechanically Treated bars TMTC-
500-10mm dia.kg 855
Thermo-Mechanically Treated bars TMTC-
500-12mm dia.kg 449
Thermo-Mechanically Treated bars TMT
Fe-500-I6mrn dia.kg 312
Mild steel 6.0 mm dia in Cannopy kg 74
Finishing work
Cement plaster in course sand
19 20mm Th Cement plaster with course
sand on outer wall from G.L to 1St Floor
Level in 1:6 cement mortar(1
cement: 6 coarse sand)
sqm 329
20 12mm Th Cement plaster with course
sand on inner wall , window sill & copla
from P.L to 1St Floor Level in 1:6 cement
mortar (1
cement: 6 coarse sand)
sqm 885
21 6mm Th Cement plaster in ceiling
1:4 cement mortar(1 cement : 4 coarse
sand)
sqm 289
Painting
22 Applying one coat of white cement primer
of approved brand and manufacture on
exterior wall surface:
sqm 328
23 Finishing walls with water proofing cement
paint(Snowcem) of approve brand and
manufacture and of required shade to give
an even shade new work (Three or more
coat).
sqm 328
24 Distempering with dry distemper of
approved brand and manufacture
(Ashian/Berger/) two or more coats and of
required shade on new work ,over and
including primimn coat of whiting to given
an even shade.
sqm 1174
25 Applying priming coat with ready mixed
aluminum primer of approved brand and
manufacture on resinous wood and
plywood.
sqm 64
Reinforcement in column,Lintel beam,Stair roof beam & roof slab up to 1St
26 Painting with synthetic enamel paint of
approved brand and manufacture with
enamel putty in all shades to give an even
shade New wood work (two or more coats)
sqm 64
27 With ready mixed zinc chromate yellow
primer of approved brand and manufacture
on steel galvanized iron/steel workssqm 39
28 Painting with synthetic enamel paint of
approved brand and manufacture with
enamel putty in all shades to give an even
shade New steel work (two or more coats)
sqm 39
Flooring work
29 Brick Flat soiling :- Providing designation
100 B one brick flat soling joints filled with
local sand including cost of watering,
taxes, royalty all complete as per building
specification and direction of E/l,
sqm 233.0
30 P.C.C Flooring:- 40mm Th cement
concrete flooring 1:2:4(1Cement:2
Coarse:4 Grade stone aggregate)finished
with a floating coat of neat cement
including cement slurry etc.
sqm 233
31 Skirting :- 18mm Th Cement plaster
skirting (up to 15 Cm height) with cement
mortar 1:3(1Cement : 3 coarse sand )
finished with a floating coat of neat cement
.
sqm 27.5
32 Ceramic Floot tile in Toilet :- Providing
and laying Ceramic glazed floor tiles
300x300 mm (thickness to be specified by
the manufacturer) of ist quality conforming
to IS : 15622 of approved make in colours
such as white , Ivory , Grey , Fume Red ,
Brown , laid on 20 mm thick Cement motar
1:4 (1 cement: 4 coarse sand ) including
pointing the joints with white cement and
matching pigment etc., complete.
sqm 24
33 Ceramic wall tile for Dado :- Providing
and fixing 1st quality ceramic glazed wall
tiles conforming to IS : 15622 (Thickness
to be specified by the manufacture) of
approved make in all colours, shades
except burgundy , bottle green , black of
any size as approved by Engineer-in-
charge in dados over 12 mm thick bed of
cement Motar 1:3(1 cement: 3 coarse sand
) and jointing with grey cement slurry @
3.3 kg per sqm including pointing in white
cement mixed with pigment of matching
shade complete.
sqm 68
Door & Window
34 Collapsible door :- Providing and fixing in
position collapsible steel shutters with
vertical channes 20x10x2 mm and braced
with flat iron diagonals 20x5 mm size with
top and bottom rail of T-tron 40x40x6 mm
with 40 mm dia steel pulleys complete with
bots.nuts locking arrangement stoppers
handies including applying a priming coat
of approved steel primer.
sqm 11
35 Door chowkhat :-Providing and fixing
pressed steel door frame confirming IS
code 351 manufactured from commerical
mild steel sheet of 1.25 mm thickness
including hinges, jamb, lock jamb, bead
and if required angle threshold of mild
steel angle of section 50 x 25 mm or base
ties of 1.25mm pressed mild steel welded
or rigidly fixed together by . mechnical
means, adjustable lugs with split end tail to
each jamb including steel butt hinges 2.5
mm thick with mortar guards, lock strike-
plate and shock absorbers as specified
and applying a coat of approved steel
primer after pre-treatment of the surface as
directed by Engineer-in-charge:
Profile C
meter 16.5
36 Door Shutter:-Providing and fixing 35mm
Th flush door shutters non-decorative
type,core of block board construction with
frame of 1 st class hard wood and well
matched commercial 3 ply veneering with
vertical grains or cross bands and face
veneers on both faces of shutters.
including anodized aluminum butt hinges
with necessary screws.
sqm 32
37 Extra for providing lipping with 2nd class
teak wood battens 25 mm minimum depth
on all edges of shutters (overall area of
door shutter to be measured)
sqm 32
38 Extra for providing vision panel not
exceeding 0.1 sqm in Director
chamber,Adm Office,Guest facuilty, of
flush doors (cost of glas excluded),
sqm 1
39 Providing and fixing 85mmx42mm oxidised
M.S. pull bolt lock conforming to IS:7534
with necessary screws bolts nut and
washers etc. complete
each 8.5
40 providing 40x5 mm flat iron hold fast 40 cm
long including fixing to frame with 10 mm
diameter bots,nuts and wooden plugs and
embeddings in cement concrete block
30x10x15 cm 1:3:6 mix (1 cement :3
coarse sand :6 graded stone aggregate 20
mm nominal size)
each 184
41 Providing and fixing oxidised M.S.tower
bolt 150x10mm black finish in toilet,(barrel
type) with necessary screws etc.completeeach 13
42 Providing and fixing bright finisned brass
100mm mortice latch and lock with 6 lever
handles with necessary screws etc.
complete.(best make of approved quality)
,Director chamber, Adm
office,guest faculity& Library.
each 4
43 Providing and fixing bright finished brass
hangging type floor door stoper with
necessary screws etc. compelte.
each 8
44 Providing and fixing IS:3564 bright finished
brass hydraulic door closer (best make of
approved quality) with necessary
accessories and screws etc.
coplete.Director Chamber & Facuilty room.
each 2
45 Providing and fixing 125 mm long
M.S.handles with necessary screws
etc.complete
Each 61
46 Window grill :- Providing and fixing M.S.
grills of requirement pattern in frames of
windows etc. with M.S. flats bars 5mm Th
& 20mm wide or 10mm x 10mm square
bars @ 100mm C/C Vertical /horizontal
etc.all complete, fixed to openings/wooden
frames with rawl plugs screws etc.
kg 60
47 Steel glazed window :- Providing and
fixing steel glazed windows and ventilatrs
of standard rolled steel sections, joints
mitered and welded with 15x3 mm lugs 10
cm long with steel lugs embedded in
cement concrete blocks 15x10x10 cm of
1:3:6(1 cement: 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) or
with woodenplugs and screws or rawl
plugs and screws or with fixing clips or
with bolts and nuts as required, including
providing and fixing of glass panes with
glazing clips and special metal-sash putty
of approved make complete including
applying a priming coat of approved steel
primer; excluding the cost of metal beading
and other fitting except necessary hinges
or pivots as required.
Sqm 40
48 Providing and fixing M.S.fan clamp type 1
of 16 mm dia.M.S. bar bent to shape with
hooked ends in R.C.C slabs during laying
including painting the exposed portion of
loop,all as per standard design complete.
each 23
49 Providing and fixing circular cast iron box
for ceiling fan clamp 140 mm internal dia,
73 mm height, 5 mm thick rim bottom and
top lids, 1.5 mm thick M.S sheet with its
top surface hacked for proper bonding top
lid shall be screwed into the cast iron box
by means of 3.3 mm dia round headed
screws, one ;pcf at the corners. Clamps
shall be made of 12 mm dia M.S. bar bent
to shape as per standard drawing.
each 23
50 Steel work welded in built up
sections/framed work including cutting
hoisting, rixing in position and applying a
priming coat of approved steel primer
using structural steel, etc. as required. M.S
Baluster 10mmx10mmx900mm each steps
,mild steel flats bar 25mmx5mm over
baluster.
kg 35
51 Providing and fixing hand rail G.I Pipes 40
mm normal bore by welding etc. to steel
ladder railings & staircases railing
including applying a priming coat of
approved steel primer . In
stringers, treads landings etc. of stair
cases.
kg 90
52 Making 0.45M Wide plinth protection
50mm thick of cement concrete 1:3:6 (1
cement :3 coarse sand : 6 graded stone
aggregate 20 mm nominal size) over
75mm thick bed of dry brick ballast 40 mm
nominal size, well rammed and
consolidated and grouted with fine sand
including finishing the top smooth.
sqm 38
Brick work
53 250mm Th Brick work with bricks of class
designation 100A at 1St Floor Level in :
Cement mortar 1:6 (1 cement: 6 coarse
sand )cum 52
54 125mm Th Half brick masonry with bricks
of class designation 100A above plinth
up to 1St floor Level in :
Cement mortar 1:4 (1 cement: 4 coarse
send)sqm 76
55 Extra for providing and placing in position
2 Nos, 6 mm dia , MS bars at every third
course of half brick masonry.sqm 76
56 Providing and laying in position machine
batched, machine mixed and machine
vibrated design mix cement concrete of
specified grade for reinforced cement
concrete structural elements, excluding the
cost of centring, shuttering finishing and
reinforcement, M-20 grade reinforced
cement concrete.
1:1:5:3(1 cement: 1.5 coarse sand:3
graded stone aggregate 20 mm nominal
size)
All work above plinth level(Walls columns,
pillars, posts cind struts)cum 7
57 Beams, planth beams, girders,
bressumers, contilevers,Suspended floors
lintels roofs and staircases including spiral
staircases, shelves etc
cum 75
Section lll (Super structure at 1St floor Level
Total Section ll:-
R.C.C work in Column ,Lintel beam & Chhaja ,Roof beam & roof Slab
58 Centring & Shuttering :- Centring and
shuttering including strutting, propping etc.
at 1St floor level and removal of form for.
Suspended floors, roofs, landings,
balconies and access platform. sqm 213
Lintels beam,roof beams, and cantilevers.sqm 46
Columns, Pillars, Piers, Abutments, Posts
and Strutssqm 111
Stairs,(excluding landings) except spiral-
staircases.sqm 11
Chhaja ,Perdi, Vertical and horizontal fins
individually or forming box louvers band,
facias and eaves boards
sqm 12.5
59 Reinforcement for R.C.C. work including
straightening, cutting, bending, placing in
position and binding all complete.
Thermo-Mechanically Treated bars TMTC-
500-8mm dia.kg 1454
Thermo-Mechanically Treated bars TMTC-
500-10mm dia.kg 855
Thermo-Mechanically Treated bars TMTC-
500-12mm dia.kg 142
Thermo-Mechanically Treated bars TMT
Fe-500-I6mrn dia.kg 210
Mild steel 6.0 mm dia in Cannopy kg 47
Finishing work
Cement plaster in course sand
60 20mm Th Cement plaster with course
sand on outer wall at 1St Floor Level in
1:6 cement mortar(1 cement: 6 coarse
sand)
sqm 326
61 12mm Th Cement plaster with course
sand on inner wall , window sill & copla
from P.L to 1St Floor Level in 1:6 cement
mortar (1 cement: 6
coarse sand)
sqm 311
62 6mm Th Cement plaster in ceiling
1:4 cement mortar(1 cement : 4 coarse
sand)
sqm 246
Painting
63 Applying one coat of white cement primer
of approved brand and manufacture on
exterior wall surface:
sqm 325
64 Finishing walls with water proofing cement
paint(Snowcem) of approve brand and
manufacture and of required shade to give
an even shade new work (Three or more
coat).
sqm 325
Reinforcement in column,Lintel beam,Stair roof beam & roof slab
65 Distempering with dry distemper of
approved brand and manufacture
(Ashian/Berger/) two or more coats and of
required shade on new work ,over and
including primimn coat of whiting to given
an even shade.
sqm 559
66 Applying priming coat with ready mixed
aluminum primer of approved brand and
manufacture on resinous wood and
plywood.
sqm 96
67 Painting with synthetic enamel paint of
approved brand and manufacture with
enamel putty in all shades to give an even
shade New wood work (two or more coats)
sqm 96
68 With ready mixed zinc chromate yellow
primer of approved brand and manufacture
on steel galvanized iron/steel workssqm 46
69 Painting with synthetic enamel paint of
approved brand and manufacture with
enamel putty in all shades to give an even
shade New steel work (two or more coats)
sqm 46
Flooring work
70 P.C.C Flooring:- 40mm Th cement
concrete flooring 1:2:4(1Cement:2
Coarse:4 Grade stone aggregate)finished
with a floating coat of neat cement
including cement slurry etc.
sqm 161
71 Skirting :- 18mm Th Cement plaster
skirting (up to 15 Cm height) with cement
mortar 1:3(1Cement : 3 coarse sand )
finished with a floating coat of neat cement
.
sqm 26.5
72 Providing and laying 20mm Th Granite
slab on cooking platform.Sqm 3.50
73 Ceramic Floot tile in Toilet :- Providing
and laying Ceramic glazed floor tiles
300x300 mm (thickness to be specified by
the manufacturer) of ist quality conforming
to IS : 15622 of approved make in colours
such as white , Ivory , Grey , Fume Red ,
Brown , laid on 20 mm thick Cement motar
1:4 (1 cement: 4 coarse sand ) including
pointing the joints with white cement and
matching pigment etc., complete.
sqm 21
74 Ceramic wall tile for Dado :- Providing
and fixing 1st quality ceramic glazed wall
tiles in toilet up to 1.8M & above cooking
platform,shink & wash basin up to 0.61M
height ,conforming to IS : 15622
(Thickness to be specified by the
manufacture) of approved make in all
colours, shades except burgundy , bottle
green , black of any size as approved by
Engineer-in-charge in dados over 12 mm
thick bed of cement Motar 1:3(1 cement: 3
coarse sand ) and jointing with grey
cement slurry @ 3.3 kg per sqm including
pointing in white cement mixed with
pigment of matching shade complete.
sqm 61
Door & Window
75 Door chowkhat :-Providing and fixing
pressed steel door frame confirming IS
code 351 manufactured from commerical
mild steel sheet of 1.25 mm thickness
including hinges, jamb, lock jamb, bead
and if required angle threshold of mild
steel angle of section 50 x 25 mm or base
ties of 1.25mm pressed mild steel welded
or rigidly fixed together by . mechnical
means, adjustable lugs with split end tail to
each jamb including steel butt hinges 2.5
mm thick with mortar guards, lock strike-
plate and shock absorbers as specified
and applying a coat of approved steel
primer after pre-treatment of the surface as
directed by Engineer-in-charge:
Profile C
meter 33
76 Door Shutter:-Providing and fixing 35mm
Th flush door shutters non-decorative
type,core of block board construction with
frame of 1 st class hard wood and well
matched commercial 3 ply veneering with
vertical grains or cross bands and face
veneers on both faces of shutters.
including anodized aluminum butt hinges
with necessary screws.
sqm 48
77 Extra for providing lipping with 2nd class
teak wood battens 25 mm minimum depth
on all edges of shutters (overall area of
door shutter to be measured)
sqm 48
78 Providing and fixing 85mmx42mm oxidised
M.S. pull bolt lock conforming to IS:7534
with necessary screws bolts nut and
washers etc. complete
each 16
79 providing 40x5 mm flat iron hold fast 40 cm
long including fixing to frame with 10 mm
diameter bots,nuts and wooden plugs and
embeddings in cement concrete block
30x10x15 cm 1:3:6 mix (1 cement :3
coarse sand :6 graded stone aggregate 20
mm nominal size)
each 184
80 Providing and fixing oxidised M.S.tower
bolt 150x10mm black finish in toilet,(barrel
type) with necessary screws etc.completeeach 12
81 Providing and fixing bright finished brass
hangging type floor door stoper with
necessary screws etc. compelte.each 15
82 Providing and fixing IS:3564 bright finished
brass hydraulic door closer (best make of
approved quality) with necessary
accessories and screws etc.in Domitory.
each 4
83 Providing and fixing 125 mm long
M.S.handles with necessary screws
etc.complete
Each 72
84 Window grill :- Providing and fixing M.S.
grills of requirement pattern in frames of
windows etc. with M.S. flats bars 5mm Th
& 20mm wide or 10mm x 10mm square
bars @ 100mm C/C Vertical /horizontal
etc.all complete, fixed to openings/wooden
frames with rawl plugs screws etc.
kg 68
85 Steel glazed window :- Providing and
fixing steel glazed windows and ventilatrs
of standard rolled steel sections, joints
mitered and welded with 15x3 mm lugs 10
cm long with steel lugs embedded in
cement concrete blocks 15x10x10 cm of
1:3:6(1 cement: 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) or
with woodenplugs and screws or rawl
plugs and screws or with fixing clips or
with bolts and nuts as required, including
providing and fixing of glass panes with
glazing clips and special metal-sash putty
of approved make complete including
applying a priming coat of approved steel
primer; excluding the cost of metal beading
and other fitting except necessary hinges
or pivots as required.
Sqm 45
86 Providing and fixing M.S.fan clamp type 1
of 16 mm dia.M.S. bar bent to shape with
hooked ends in R.C.C slabs during laying
including painting the exposed portion of
loop,all as per standard design complete.
each 23
87 Providing and fixing circular cast iron box
for ceiling fan clamp 140 mm internal dia,
73 mm height, 5 mm thick rim bottom and
top lids, 1.5 mm thick M.S sheet with its
top surface hacked for proper bonding top
lid shall be screwed into the cast iron box
by means of 3.3 mm dia round headed
screws, one ;pcf at the corners. Clamps
shall be made of 12 mm dia M.S. bar bent
to shape as per standard drawing.
each 23
88 Water Proofing :- Providing and laying
water proofing treatment to vertical and
horizontal surfaces of depressed portions
of W.C. kitchen and the like consisting of:
(i) 1st course of applying cement slurry @
4.4 kg/sqm mixed with water proofing
compound conforming tc IS 2645 in
recommended proportions.
(ii) 11 nd course of 20 mm cement plaster
1:3 (1 cement:3 coarse sand)mixed
with water proofing compound in
recommended proportion, (iii)
Illrd course of applying blown or/residual
bitumen aplied hot at 1.7 kg. per sqm of
area, (iv) Ivth course of 400 micron
thick PVC sheet.(Overlaps at joints of PVC
shet should be 100 mm wide and pasted to
each other with bitumen @ 1.7 kg/sqni).
sqm 30
89 Steel work welded in built up
sections/framed work including cutting
hoisting, rixing in position and applying a
priming coat of approved steel primer
using structural steel, etc. as required. M.S
Baluster 10mmx10mmx900mm each steps
,mild steel flats bar 25mmx5mm over
baluster.
kg 35
90 Providing and fixing hand rail G.I Pipes 40
mm normal bore by welding etc. to steel
ladder railings & staircases railing
including applying a priming coat of
approved steel primer . In
stringers, treads landings etc. of stair
cases.
kg 90
Total Section lll:-
Brick work
91 250mm Th Brick work with bricks of class
designation 100A at 1St Floor Level in :
Cement mortar 1:6 (1 cement: 6 coarse
sand )cum 56
92 125mm Th Half brick masonry with bricks
of class designation 100A above plinth
up to 1St floor Level in :
Cement mortar 1:4 (1 cement: 4 coarse
send)sqm 26
93 Extra for providing and placing in position
2 Nos, 6 mm dia , MS bars at every third
course of half brick masonry.sqm 26
94 Providing and laying in position machine
batched, machine mixed and machine
vibrated design mix cement concrete of
specified grade for reinforced cement
concrete structural elements, excluding the
cost of centring, shuttering finishing and
reinforcement, M-20 grade reinforced
cement concrete.
1:1:5:3(1 cement: 1.5 coarse sand:3
graded stone aggregate 20 mm nominal
size)
All work above plinth level(Walls columns,
pillars, posts cind struts)cum 6.5
Beams, planth beams, girders,
bressumers, contilevers,Suspended floors
lintels roofs and staircases including spiral
staircases, shelves etc
cum 56
95 Centring & Shuttering :- Centring and
shuttering including strutting, propping etc.
at 1St floor level and removal of form for.
Suspended floors, roofs, landings,
balconies and access platform.sqm 205
Lintels beam,roof beams, and cantilevers.sqm 102
Columns, Pillars, Piers, Abutments, Posts
and Strutssqm 96
Stairs,(excluding landings) except spiral-
staircases.sqm 12
SECTION IV -AT SECOND FLOOR
R.C.C work in Column ,Lintel beam & Chhaja ,Roof beam & roof Slab
Chhaja ,Perdi, Vertical and horizontal fins
individually or forming box louvers band,
facias and eaves boards
sqm 12
96 Reinforcement for R.C.C. work including
straightening, cutting, bending, placing in
position and binding all complete.
Thermo-Mechanically Treated bars TMTC-
500-8mm dia.kg 1426
Thermo-Mechanically Treated bars TMTC-
500-10mm dia.kg 855
Thermo-Mechanically Treated bars TMTC-
500-12mm dia.kg 17
Thermo-Mechanically Treated bars TMT
Fe-500-I6mrn dia.kg 98
Mild steel 6.0 mm dia in cannopy kg 47
Finishing work
Cement plaster in course sand
97 20mm Th Cement plaster with course
sand on outer wall at 1St Floor Level in
1:6 cement mortar(1 cement: 6 coarse
sand)
sqm 173
98 12mm Th Cement plaster with course
sand on inner wall , window sill & copla
from P.L to 1St Floor Level in 1:6 cement
mortar (1 cement: 6
coarse sand)
sqm 235
99 6mm Th Cement plaster in ceiling
1:4 cement mortar(1 cement : 4 coarse
sand)
sqm 132
Painting
100 Applying one coat of white cement primer
of approved brand and manufacture on
exterior wall surface:
sqm 175
101 Finishing walls with water proofing cement
paint(Snowcem) of approve brand and
manufacture and of required shade to give
an even shade new work (Three or more
coat).
sqm 175
102 Distempering with dry distemper of
approved brand and manufacture
(Ashian/Berger/) two or more coats and of
required shade on new work ,over and
including primimn coat of whiting to given
an even shade.
sqm 367
103 Applying priming coat with ready mixed
aluminum primer of approved brand and
manufacture on resinous wood and
plywood.
sqm 31
Reinforcement in column,Lintel beam,Stair roof beam & roof slab
104 Painting with synthetic enamel paint of
approved brand and manufacture with
enamel putty in all shades to give an even
shade New wood work (two or more coats)
sqm 31
105 With ready mixed zinc chromate yellow
primer of approved brand and manufacture
on steel galvanized iron/steel workssqm 28
106 Painting with synthetic enamel paint of
approved brand and manufacture with
enamel putty in all shades to give an even
shade New steel work (two or more coats)
sqm 28
Flooring work
107 P.C.C Flooring:- 40mm Th cement
concrete flooring 1:2:4(1Cement:2
Coarse:4 Grade stone aggregate)finished
with a floating coat of neat cement
including cement slurry etc.
sqm 50
108 Skirting :- 18mm Th Cement plaster
skirting (up to 15 Cm height) with cement
mortar 1:3(1Cement : 3 coarse sand )
finished with a floating coat of neat cement
.
sqm 21.0
109 Providing and laying 20mm Th Granite
slab on cooking platform.Sqm 8.0
110 Ceramic Floot tile in Toilet :- Providing
and laying Ceramic glazed floor tiles
300x300 mm (thickness to be specified by
the manufacturer) of ist quality conforming
to IS : 15622 of approved make in colours
such as white , Ivory , Grey , Fume Red ,
Brown , laid on 20 mm thick Cement motar
1:4 (1 cement: 4 coarse sand ) including
pointing the joints with white cement and
matching pigment etc., complete.
sqm 6.5
111 Ceramic wall tile for Dado :- Providing
and fixing 1st quality ceramic glazed wall
tiles in toilet up to 1.8M & above cooking
platform,shink & wash basin up to 0.61M
height ,conforming to IS : 15622
(Thickness to be specified by the
manufacture) of approved make in all
colours, shades except burgundy , bottle
green , black of any size as approved by
Engineer-in-charge in dados over 12 mm
thick bed of cement Motar 1:3(1 cement: 3
coarse sand ) and jointing with grey
cement slurry @ 3.3 kg per sqm including
pointing in white cement mixed with
pigment of matching shade complete.
sqm 27
Door & Window
112 Door chowkhat :-Providing and fixing
pressed steel door frame confirming IS
code 351 manufactured from commerical
mild steel sheet of 1.25 mm thickness
including hinges, jamb, lock jamb, bead
and if required angle threshold of mild
steel angle of section 50 x 25 mm or base
ties of 1.25mm pressed mild steel welded
or rigidly fixed together by . mechnical
means, adjustable lugs with split end tail to
each jamb including steel butt hinges 2.5
mm thick with mortar guards, lock strike-
plate and shock absorbers as specified
and applying a coat of approved steel
primer after pre-treatment of the surface as
directed by Engineer-in-charge:
Profile C
meter 10.5
113 Door Shutter:-Providing and fixing 35mm
Th flush door shutters non-decorative
type,core of block board construction with
frame of 1 st class hard wood and well
matched commercial 3 ply veneering with
vertical grains or cross bands and face
veneers on both faces of shutters.
including anodized aluminum butt hinges
with necessary screws.
sqm 16
114 Extra for providing lipping with 2nd class
teak wood battens 25 mm minimum depth
on all edges of shutters (overall area of
door shutter to be measured)
sqm 16
115 Providing and fixing 85mmx42mm oxidised
M.S. pull bolt lock conforming to IS:7534
with necessary screws bolts nut and
washers etc. complete
each 2
116 providing 40x5 mm flat iron hold fast 40 cm
long including fixing to frame with 10 mm
diameter bots,nuts and wooden plugs and
embeddings in cement concrete block
30x10x15 cm 1:3:6 mix (1 cement :3
coarse sand :6 graded stone aggregate 20
mm nominal size)
each 8
117 Providing and fixing oxidised M.S.tower
bolt 150x10mm black finish in toilet,(barrel
type) with necessary screws etc.completeeach 2
118 Providing and fixing bright finished brass
hangging type floor door stoper with
necessary screws etc. compelte.
each 8
119 Providing and fixing 125 mm long
M.S.handles with necessary screws
etc.complete
Each 8
120 Window grill :- Providing and fixing M.S.
grills of requirement pattern in frames of
windows etc. with M.S. flats bars 5mm Th
& 20mm wide or 10mm x 10mm square
bars @ 100mm C/C Vertical /horizontal
etc.all complete, fixed to openings/wooden
frames with rawl plugs screws etc.
kg 42
121 Steel glazed window :- Providing and
fixing steel glazed windows and ventilatrs
of standard rolled steel sections, joints
mitered and welded with 15x3 mm lugs 10
cm long with steel lugs embedded in
cement concrete blocks 15x10x10 cm of
1:3:6(1 cement: 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) or
with woodenplugs and screws or rawl
plugs and screws or with fixing clips or
with bolts and nuts as required, including
providing and fixing of glass panes with
glazing clips and special metal-sash putty
of approved make complete including
applying a priming coat of approved steel
primer; excluding the cost of metal beading
and other fitting except necessary hinges
or pivots as required.
Sqm 28
122 Providing and fixing M.S.fan clamp type 1
of 16 mm dia.M.S. bar bent to shape with
hooked ends in R.C.C slabs during laying
including painting the exposed portion of
loop,all as per standard design complete.
each 6
123 Providing and fixing circular cast iron box
for ceiling fan clamp 140 mm internal dia,
73 mm height, 5 mm thick rim bottom and
top lids, 1.5 mm thick M.S sheet with its
top surface hacked for proper bonding top
lid shall be screwed into the cast iron box
by means of 3.3 mm dia round headed
screws, one ;pcf at the corners. Clamps
shall be made of 12 mm dia M.S. bar bent
to shape as per standard drawing.
each 6
124 Water Proofing :- Providing and laying
water proofing treatment to vertical and
horizontal surfaces of depressed portions
of W.C. kitchen and the like consisting of:
(i) 1st course of applying cement slurry @
4.4 kg/sqm mixed with water proofing
compound conforming tc IS 2645 in
recommended proportions.
(ii) 11 nd course of 20 mm cement plaster
1:3 (1 cement:3 coarse sand)mixed
with water proofing compound in
recommended proportion, (iii)
Illrd course of applying blown or/residual
bitumen aplied hot at 1.7 kg. per sqm of
area, (iv) Ivth course of 400 micron
thick PVC sheet.(Overlaps at joints of PVC
shet should be 100 mm wide and pasted to
each other with bitumen @ 1.7 kg/sqni).
sqm 7.5
125 Steel work welded in built up
sections/framed work including cutting
hoisting, rixing in position and applying a
priming coat of approved steel primer
using structural steel, etc. as required. M.S
Baluster 10mmx10mmx900mm each steps
,mild steel flats bar 25mmx5mm over
baluster.
kg 35
126 Providing and fixing hand rail G.I Pipes 40
mm normal bore by welding etc. to steel
ladder railings & staircases railing
including applying a priming coat of
approved steel primer . In
stringers, treads landings etc. of stair
cases.
kg 90
Brick work
127 250mm Th Brick work with bricks of class
designation 100A at 1St Floor Level in :
Cement mortar 1:6 (1 cement: 6 coarse
sand )cum 27
128 Providing and laying in position machine
batched, machine mixed and machine
vibrated design mix cement concrete of
specified grade for reinforced cement
concrete structural elements, excluding the
cost of centring, shuttering finishing and
reinforcement, M-20 grade reinforced
cement concrete.
1:1:5:3(1 cement: 1.5 coarse sand:3
graded stone aggregate 20 mm nominal
size)
All work above plinth level(Walls columns,
pillars, posts cind struts)cum 1.5
Beams, planth beams, girders,
bressumers, contilevers,Suspended floors
lintels roofs and staircases including spiral
staircases, shelves etc
cum 55
129 Centring & Shuttering :- Centring and
shuttering including strutting, propping etc.
at 2nd floor level and removal of form for.
Suspended floors, roofs, landings,
balconies and access platform.sqm 205
Lintels beam,roof beams, and cantilevers.sqm 102
Columns, Pillars, Piers, Abutments, Posts
and Strutssqm 95
130 Reinforcement for R.C.C. work including
straightening, cutting, bending, placing in
position and binding all complete.
Thermo-Mechanically Treated bars TMTC-
500-8mm dia.kg 1426
Thermo-Mechanically Treated bars TMTC-
500-10mm dia.kg 855
Thermo-Mechanically Treated bars TMTC-
500-12mm dia.kg 70
Thermo-Mechanically Treated bars TMT
Fe-500-I6mrn dia.kg 98
Finishing work
Cement plaster in course sand
Total Section lV:-
Section V ( Mumty B/U Area 35Sqm & Parapet wall)
R.C.C work in Column Roof beam & mumty Slab
Reinforcement in column,roof beam & mumty slab
131 20mm Th Cement plaster with course
sand on outer wall at 1St Floor Level in1:6
cement mortar(1 cement: 6 coarse sand)sqm 59
132 12mm Th Cement plaster with course
sand on inner wall , window sill & copla
from P.L to 1St Floor Level in 1:6 cement
mortar (1 cement: 6
coarse sand)
sqm 57
133 6mm Th Cement plaster in ceiling
1:4 cement mortar(1 cement : 4 coarse
sand)
sqm 131
Painting
134 Applying one coat of white cement primer
of approved brand and manufacture on
exterior wall surface:
sqm 62
135 Finishing walls with water proofing cement
paint(Snowcem) of approve brand and
manufacture and of required shade to give
an even shade new work (Three or more
coat).
sqm 65
136 Distempering with dry distemper of
approved brand and manufacture
(Ashian/Berger/) two or more coats and of
required shade on new work ,over and
including primimn coat of whiting to given
an even shade.
sqm 137
137 With ready mixed zinc chromate yellow
primer of approved brand and manufacture
on steel galvanized iron/steel workssqm 9.5
138 Painting with synthetic enamel paint of
approved brand and manufacture with
enamel putty in all shades to give an even
shade New steel work (two or more coats)
sqm 10
Door & Window
139 Door chowkhat :-Providing and fixing
pressed steel door frame confirming IS
code 351 manufactured from commerical
mild steel sheet of 1.25 mm thickness
including hinges, jamb, lock jamb, bead
and if required angle threshold of mild
steel angle of section 50 x 25 mm or base
ties of 1.25mm pressed mild steel welded
or rigidly fixed together by . mechnical
means, adjustable lugs with split end tail to
each jamb including steel butt hinges 2.5
mm thick with mortar guards, lock strike-
plate and shock absorbers as specified
and applying a coat of approved steel
primer after pre-treatment of the surface as
directed by Engineer-in-charge:
Profile C
meter 11
140 Door Shutter:-Providing and fixing 35mm
Th flush door shutters non-decorative
type,core of block board construction with
frame of 1 st class hard wood and well
matched commercial 3 ply veneering with
vertical grains or cross bands and face
veneers on both faces of shutters.including
anodized aluminum butt hinges with
necessary screws.
sqm 4.6
141 Extra for providing lipping with 2nd class
teak wood battens 25 mm minimum depth
on all edges of shutters (overall area of
door shutter to be measured)
sqm 5
142 Providing and fixing 85mmx42mm oxidised
M.S. pull bolt lock conforming to IS:7534
with necessary screws bolts nut and
washers etc. complete
each 4
143 providing 40x5 mm flat iron hold fast 40 cm
long including fixing to frame with 10 mm
diameter bots,nuts and wooden plugs and
embeddings in cement concrete block
30x10x15 cm 1:3:6 mix (1 cement :3
coarse sand :6 graded stone aggregate 20
mm nominal size)
each 12
144 Providing and fixing oxidised M.S.tower
bolt 150x10mm black finish ,(barrel type)
with necessary screws etc.completeeach 2
145 Providing and fixing 125 mm long
M.S.handles with necessary screws
etc.complete
Each 2
146 Window grill :- Providing and fixing M.S.
grills of requirement pattern in frames of
windows etc. with M.S. flats bars 5mm Th
& 20mm wide or 10mm x 10mm square
bars @ 100mm C/C Vertical /horizontal
etc.all complete, fixed to openings/wooden
frames with rawl plugs screws etc.
kg 16
147 Steel glazed window :- Providing and
fixing steel glazed windows and ventilatrs
of standard rolled steel sections, joints
mitered and welded with 15x3 mm lugs 10
cm long with steel lugs embedded in
cement concrete blocks 15x10x10 cm of
1:3:6(1 cement: 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) or
with woodenplugs and screws or rawl
plugs and screws or with fixing clips or
with bolts and nuts as required, including
providing and fixing of glass panes with
glazing clips and special metal-sash putty
of approved make complete including
applying a priming coat of approved steel
primer; excluding the cost of metal beading
and other fitting except necessary hinges
or pivots as required.
Sqm 10.0225
148 Providing and laying APP (Atactic
Polypropylene Polymer) modified
prefabricated five layer, 3 mm thick water
proofing membrane, black finished
reinforced with glass fibre matt consisting
of a coat of bitumen primer for bitumen
membrane @0.40 litre/ sqm by the same
membrane manufactured of density at 25°
C, 0.87 - 0.89 kg/ litre and viscocity 70 -
160 cps. Over the primer coat the layer of
membrane shall be laid using butane torch
and sealing all joints etc., and
preparing the surface complete. The vital
physical and chemical parameters of the
membrane shall be as under : Joint
strength in longitudinal and transverse
direction at 23°C as 350/300 N/5 cm. Tear
strength in longitudinal and transverse
direction as 60/80N. Softening point of
membrane not less than 150°C. Cold
flexibility shall be upto -
2°C when tested in accordance with
ASTM, D - 5147. The laying of membrane
shall be got done through the authorised
applicator of the
manufacturer of membrane.
sqm 310
Total Section V:-
Grand total Sub head A-
Section l (Electric wiring)
SL No DESCRIPTION OF WORK UNIT QUANTITY RATE AMOUNT
1
Point wiring in pvc conduit with modular
type switch wiring for lightpt/ fan pt / call
bell pt with 1.5 S Q.m.m.F.R pvc insulated
copper conductor single core cable in
surface/ recessed pvc conduit with
modular type switch , modular plate
suitable size GI boox etc as required.
a Group C each 153
b Group A each 35
2
Twin control wiring in pvc conuit with
modular type switch : wiring in pvc conduit
with modular type switch: wiring for twin
control light point with 1.5 S Qmm F.R pvc
insulated copper conductor single core
cable in surface / recessed pvc conduit, 2
way modular type switch, modular plate
suilable size GI Box etc as required
point 3.00
3
Power plug wiring in pvc conduit
(2x4Sqmm) – wiring for light / power plug
with 2x4 SQ.mm.F.R pvc insulated copper
conductor single core cable in surface/
recessed pvc conduit, along with 1No
4&Q.mm.F.R pvc insulated copper
conductor single core cable for loop
earthing as required
Mtr 110.00
4
Circuit/ sub main wiring in pvc conduit:
wiring for circuit /sub main wiring along
with earth wire with following size of pvc
insulated copper conductor single core
surface/recessed pvc conduit as required
a 2x1.5+1x2.5 Mtr 192
b 2x2.5+1x2.5 Mtr 314
c 4x6+2x6 Mtr 35
d 4x10+2x10 Mtr 24
5
Telephone wiring in existing conduit:
supplying and drawing following pair 0.5
SQmm.F.RLS pvc insulated copper
conductor unarmoured telephone cable in
the existing surface/ recessed pvc conduit
as required
SUB HEAD B (ELECTRICAL WORK) GROUND,1St & 2nd FLOOR
a 2 pair Meter 232
6
S/F pvc conduit supply and fixing following
sizes pvc conduit along with accessories in
surface /recess including cutting the wall
and making good the same in case
recessed conduit as required
a 25mm Mtr 26
7
S/F modular type switch/socket:- supplying
and fixing following modular type
switch/socket on the existing modular plate
and switch box in duding connection but
excluding modular plate etc.
a 5 amp one way switch each 45
b 5 /6 amp 3 pin socket out let each 45
c 15/16 amp 6 pin socket out let each 7
d 15/16 amp one way swich each 7
e telephone socket outlat each 8
8
S/F modular box base and cover plate
supplying and fixing modular GI boxes
along with modular base and cover plate
for modular switch & socket etc as
required .
a 1 or 2 module (75x75x45)mm each 18
b 4/5 module (78x140x50)mm each 19
9
S/F suitable size GI box with modular plate
cover in front on surface or in recess
including providing and fixing 6 pin, 15/16
amp modular socket outlet and 15/16 amp
switch connection painting etc.
each 3
10S/F ceiling rose supply and fixing 2 pin
same ceiling rose on existing jn box each 106
11Batten holder :-supplying & fixing
batten/angular holder including connection
etc as required.
each 4
12
S/Fdingdong call bell:-supply and fixing
dingdong call bell suitable for DC/AC
single phase 230 volte complete as
required
each 1
13
S/F twin twisted cable in conduct :-Twin
twisted cable in conduit P/F plain 16/0.20
mm (0.50 SQmm) twin twisted FR pvc
insulated copper cable in polythene sleeve
of suitable size on floor/wall.
each 106
14
ITC Fluorescent fitting directly on
surface:- Installation testing and
commissioning of per – wired ,fluoresent
fitting of alln type ,complete with all fitting
of all type complete with all accessories
and tube etc directly on ceiling/wall
including connection with 1.5 SQ mm FR
pvc insulated copper conductor ,single
core cable and earthing etc. as required
each 93
15
S/F 20 amp, 240v SPN industrial type
socket out let with 2 pole and earth, metal
enclosed plug top along with 20A C' serier
P MCB in sheet steel encloser on
surfagrears with chained metal sover
farthe socket complte with connection etc
or as requived.
each 3
16
I.T.C ceiling fan:- installation testing and
commissioning of ceiling fan including
wiring the down road of standard length
(up to 30 cm) with 1.5 SQ.mm FR pvc
insulated copper conductor, single core
cable as required.
each 44
17
S/f modular electronic fan regulator:-
S/F stepped type electronic fan regulator
the existing modular plate switch box
including connection but excluding
modular plate etc.
each 44
18
I.T.C Exhaust fan up to 450mm sweep:-
Installation of exhaust fanup to 450 mm.
sweep in the existing opening including
making the hole to suit the size of the
above fan making good the dimage
connection testing commissioning etc as
required
each 14
19
Fixing louvers shutter for exhaust fan extra
for fixing the louvers shutters complete
with frame for a exhaust fan of all size.
each 14
20
Supply and fixing TPMCB supply and
fixing following way three pole and neutral
sheet MCB distribution board 415v on
surface/recess complete with tinned
copper bus- bar neutral bus- bar earth bar
din bar detachable glane plate inter
connections phos phatized and power
pointed including earthing etc as required
(But without MCB/RCCB/isolator )
a 6way (4+18)double door horizontal type each 6
21
S/F `C` series MCB :- supply and fixing
following 240 volts `C` series MCB suitable
for inductive loads of following poles in the
existing MCB DB complete with connection
testing and commissioning etc as required.
a 6/32 amps S.P each 30
22
S/F four pole MCB Isolator:- supply and
fixing following rating four pole 415volt
isolator in existing MCB DB complete with
connection testing and commissioning etc
as required
a 63 amps each 2
b 40 amps each 4
23
S/F TPN RCCB:- supplying and fixing
following rating TPN 415V RCCB, having a
sensitivity current up to 300 ma in the
existing MCB-DB complete with
connection testing and commissioning etc
as required.a 63 amps each 1
b 100 amp each 1
24Supply and fixing blanking plate (sing pe
pote in existair Db)each 32
25
S/F bus bar chamber:- providing and
fixing following rating bus bar chamber
with 4 strip of suitable size made of copper
heavy duty complete with all accessories
including connection earthing the body etc
as required
a 200 amps each 1
26
S/f MCCB in cubical panel board :-
providing and fixing following rating and
capacity four pole MCCB in existing
capacity cubical panel board including
holes in cubical panel making connection
etc as required a 200 amps 35ka fixed thermal setting each 1
27
Copper earth plate electrode:- Ear thing
with copper plate 600mmx600mmx3mm
thick including accessories and providing
masonry in closer with plate having locking
arrangement and watering pipe etc as
required with char coal and salt and salt
as required
set 2
28
S/L 8SWG Copper wire in ground:-
supplying and laying 8 SWG copper wire
at 0.5 meter below Gr level for conductor
earth electrode including soldering etc as
required
Mtr 66
Total Section I -
Section ll (Lighting conductor)
29
Earth plate Electrode:- Earth with GI
earth plate 600mmx600mmx6mm thick
including accessories encloser with cover
plate having locking arrangements and
watering pipe etc as required ( but with out
– char coal or coke and salt)
set 2
30
Salt/coke for plate earth electrode:-
Extra for using saltandRE charcoal far GI
or copper plate earth electrode as required
set 2
31
P/F copper lightning conductor finial, made
of 25mm dia 300mm long GI tube having
single prong at top with 85mm 3mm thick
GI base plate including holes etc complete
as required
each 2
32
Reverting, sweating and soldering
conductor:- reverting & lightring and
soldering of GI tape (with another copper)
GI tape, base of the final or any other
metallic object as required.
each 28
33
P/F GI lightring conductor tape in
horizontal run:- Providing and fixing GI
tape 20mm x 3mm tick on parapet or
surface of wall for lightring conductor
complete as required
Mtr 123
34
P/F GI lightring conductor tape in
vertical run:- Providing and fixing GI tape
20mm x 3mm tick on parapet or surface of
wall for lightring conductor complete as
required
Mtr 15
35
P/F testing joint for GI lightring
conductor:- providing and fixing testing
joints made of 20mm x 3mm thick GI strip
125mm long with 4 nos GI bolts nuts check
nuts and spring washersetc. Complete as
required
each 56
36
P/F GI earth tape for lightring
conductor:- providing and laying GI tape
32mm x 6mm earth electrode directly
ingras Required.
Mtr 16
37
MV cable laying up to 120 Sqmm in Gr :-
Laying of one no PVC insulated and PVC
sheathed/ XLPE power cable of 1.1KV
grade of size not exceeding 120 Sqmm
ground including excavation protective
covering and re Filling the trench etc as
required
Mtr 90
38
P/F danger notice plate providing and
fixing MV danger notice plate 200mmv
150mm made of mild steel at least 2 mm
thick and vitreous White on both side with
inscription in single red color on front side
each 1
39
S/F panel mounted change over
switches:- Providing and fixing following
capacity 4 pole panel mounted change
over switches in existing cubical panel
board making connection earthing the
body etc as required
a 200A 4 pole each 1
b Supply of 3.5 x 50 Sqmm x LPE/PVCA (Al) cable 1.1KV gradeMtr 90
40
Supply,installation, testing &
commissioning of the following light
fixtures complete with lamps, electronic
ballasts, lamp holder, starter, starter
holder, etc. duly wired complete for use on
240 V single phase 50 Hz AC supply
including all accessories required for
mounting at surface/recess/wall as
mentioned in BOQ and drawings
conforming to relavant IP protection and
IS codes.
a
Supply & Fixing 1 x 28 W fluorescent tube
light fitting Make Havells Lamp Type -
1x28W FTL T5 ,Odering code -
LHIT81128032
66
b
Supply & fixing 1x14W Fluorescent wall
mounted mirror luminaire (Philips Cat NO
-ADRENO V2 14WTWG 207 1xTL5-14W 2
c
1 x 9 W CFL wall bracket fitting make
Phillips/Bajaj/Crompton/equivalent+ isi
market
15
41
Supply and fixing surface down light make
havells , Lamp type -2x18W PL-C/DU-CFL
Ordering code -LHOC1521845419
42
Providing and fixing with 18/20w CFL
(essential) in existing angular/ battu Holder
make Phillips/Bajaj/Crompton
each 5
43
Supply of 56" (1440mm)sweep double ball
bearing ceiling fan with down rod, shackle
insulator canopy complete but without
regulator 230V AC make Crompton/
havells or equivallant i.s.i market
each 48
44
Supply of 12” (300mm)sweep exhaust fan
heavy duty double ball bearing 230V AC
make Crompton/ havells or equivallant i.s.i
market
each 14
45
Supply and fixing cubical type panel box to
accommodate 200A 4 pole change over
switch complete with all accessories and
gland box for cables termination (incomer
and out going cables)
Each 1
46 S/F roary Switch 63A Each 1
47
End termination of Armod cable 50Sqmm
Each 2
Section lll -EXTERNAL ELECTRIFICATION
48 Supply ,fabrication and delivery of tubular
poles for street light 9 M long (SP-31) with
base plate for street light (IS-1161-SP -31) Each 6
49 Supply of skyline SGP-325 Street light
luminaire with press wire die-cast
Aluminum housing POT -optics reflector
and heat resistant toughened flat glass
cover (IP-65)SGP 325-1x1+PITP-150W
FG.
Each 6
50 Supply of 4x10Sqmm x LPE PVC
Aluminum armoured cabel 1.1 KV grade. 200
51 Supply of 63Amp TPN Switch with HRC
Fuses.Each 1
Section lll:-
Total sub head B -
Total Section II -
Sl No Description Item Ground floor estimate Unit Quantity Rate Amount
(I) Sub-Head-l
WATER SUPPLY
G.I. PIPES AND FITTINGS
1
Providing and fixing G.I. pipes
complete with G.I. fittings and clamps,
including cutting and making good the wall
etc.
(A) 20 mm dia. Nominal bore Metre 62.00
(B) 25 mm dia. Nominal bore Metre 40.00
(C) 32 mm dia. Nominal bore Metre 6.00
(D) 40 mm dia. Nominal bore Metre 40.00
2
Concealed pipe including with anti
corrosive bitumatic paint, cutting chases
and making good the wall.
(A) 15 mm dia. Nominal bore Metre 85.00
(B) 20 mm dia. Nominal bore Metre 65.00
3
Providing and fixing G.I. pipes
complete with G.I. fittings including
trenching and refilling etc.
(B) 40 mm dia. Nominal bore Metre 25.00
SUB HEAD C (P.H.E WORK) GROUND,1st & 2nd FLOOR Ground ,1St Floor,2nd Floor
4
Making connecting of G.I. distribution
branch with G.I. Main of following sizes
by providing and fixing tee, including
cutting and threading the pipe etc.
complete.
(A) 25 to 40 mm Nominal bore each 3.00
5Providing and fixing brass stop cock of
approved quality
(A) 20 mm Nominal bore each 9.00
6Providing and fixing brass gate valve with
C.I. wheel of approved quality.
(A) 32 mm Nominal bore Each. 1.00
(B) 40mm Nominal bore Each. 1.00
7Providing and fixing metal non-return
valve of approved quality.
32 mm nominal bore
Horizontal Each. 1.00
Vertical Each. 1.00
40 mm nominal bore
Horizontal Each. 1.00
Vertical Each. 1.00
8
Painting G.I. pipe and fittings with synthetic
enamel white paint over a ready mixed
priming coat, both of approved quality for
new work.
(A) 20 mm dia. Nominal bore Metre 12.00
(B) 25 mm dia. Nominal bore Metre 40.00
(C) 32 mm dia. Nominal bore Metre 6.00
(D) 40 mm dia. Nominal bore Metre 40.00
9
Providing and fixing G.I. union in G.I.pipe
including cutting and threading the pipe
and making long screws etc.
(A) 20 mm dia. Nominal bore each 4.00
(B) 25mm dia. Nominal bore each 7.00
(D) 40 mm dia. Nominal bore each 10.00
10
Providing and placing on terrace (at all
floor levels ) polythethylene water storage
tank of approved brand and manufacture
with cover and suitable locking
arrangement and making necessary holes
for inlet, outlet and overflow pipes but
without fittings and the base support for
tank 1000X7=7000 litre 7000.00
C.P. BRASS FITTINGS
11
Providing and fixing C.P brass bib cock of
approved quality confirming to IS:8931
15mm nominal bore Each 26.00
12
Providing and fixing C.P brass long nose
bib cock of approved quality confirming to
IS standard and weighing not less
than810grams.15mm nominal bore Each 2.00
13
Providing and fixing C.P brass stop cock
(concealed) of standard design and of
approved make confirming to IS:8931
15mm nominal bore Each 14.00
14Providing and fixing CP brass shower rose
15 or 20 mm inlet150 mm diameter
Each 6.00
(II) Sub-Head-ll
Sanitary Installation
15
Providing and fixing water closet
squatting pan (Indian type W.C. pan )
with 100mm sand cast Iron P or S trap,
10 litre low level white P.V.C. flushing
cistern with manually controlled device
(handle lever) conforming to IS : 7231,
with all fittings and fixtures complete
including cutting and making good the
walls and floors wherever required :
(a)
White vitreous china orissa pattern W.C.
pan of size 580 x 440mm with integral
type foot rests.
Each 6.00
16
Providing and fixing white vitreous china
pedestal type water closet (European
type) with seat and lid, 10 litre low level
white vitreous china flushing cistern &
C.P. flush bend with fittings &
C.I.brackets, 40mm flush bend, overflow
arrangement with specials of standard
make and mosquito proof coupling of
approved municipal design complete
including painting of fittings and
brackets, cutting and making good the
walls and floors wherever required :
Total sub head -l
(a)W.C. Pan with ISI marked white solid
plastic seat and lid.Each 6.00
17
Provding and fixing white vitreous china
wash basin with C.I./ MS brackets, 15 mm
C.P. brass pillar taps, , 32 mm C.P. brass
waste of standard pattern, including
paintings of fittings and brackets, cutting
and making good the .wall wherever
required.
flat back wash basin size 630X450mm
with single15mm CP pillar tapEach 13.00
18
Providing and fixing PTMT Bottle Trap for
Wash basin and sink. Bottle trap 31mm
single piece moulded with height of
270mm, effective length of tail pipe 260mm
from the centre of the waste coupling
77mm breadth with 25mm minimum water
seal, weighing not less than 260gms.
Each 13.00
19
Provding and fixing 600X450mm
bevelled edge mirror of superior glass
complete with 6mm thick hard board
ground fixed to wooden cleats with CP
brass screws & washers complete.
Each 12.00
20
Provding and fixing 600X120X5 mm glass
shelf with edges rounded off supported on
anodised aluminium angle frame with CP
brass brackets and guard rail complete
fixed with 40 mm long screws ,rawl plug
etc, complete.
Each 12.00
21
Provding and fixing towel rail complete
with brackets fixed to wooden cleats with
CP brass screws
600 X 20 mm size Each 7.00
22
Provding and fixing kitchen sink with C.I.
brackets, C.P. brass chain with rubber
plug,40mm CP brass waste complete ,
including paintings of fittings and brackets,
cutting and making good the .wall
wherever required.
white glazed fire clay sink of size
600x450x250mmEach 3.00
23
Provding and fixing PVC waste pipe for
sink & wash basin including PVC waste
fittings complete
40 mm dia Each 15.00
24.0Providing and fixing soil waste and vent
pipes
(a)
100mm diameter Centrifugally cast
(spun) iron socketed pipe as per IS:
3989.
Metre 135
(b)75mm diameter Centrifugally cast (spun)
iron socketed pipe as per IS: 3989.Metre 30
25.0
Providing and fixing M.S. holder-bat
clamps of approved design to sand cast
iron centrifugally cast (spun) iron S&S
pipes embedded in and including cement
concrete blocks 10x 10 x 10 cm of 1:2:4
mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20mm nominal size)
including cost of cutting holes and
making good the walls, etc.
(a) For 100mm dia pipe Each 75
(b) For 75 mm dia. Pipe Each 17
26
Providing and fixing single equal plain
junction of required degree with access
door, insertion rubber washer 3mm thick,
bolts and nuts complete
(a)100 x 100 x 100mm Sand cast iron S&S
as per IS - 3989Each 20
27
Providing and fixing single unequal
junction of required degree with access
door, insertion rubber washer 3mm thick,
bolts and nuts complete.
(a)100 x 100 x 75mm Sand cast iron S&S
as per IS - 3989Each 11
28Providing and fixing single equal plain
junction of required degree.
(a)100 x 100 x 100mmSand cast iron S&S
as per IS - 3989Each 2
29Providing and fixing single unequal plain
junction of required degree.
(a)100 x 100 x 75mm Sand cast iron S&S
as per IS - 3989Each 2
30 Providing and fixing terminal guard
(a)100mm Sand cast iron S&S as per IS -
3989Each 7
(b)75mm Sand cast iron S&S as per IS -
3989Each 1
31
Providing lead caulked joints to sand
cast iron/centrifugally cast (spun) iron
pipes and fittings of diameter
(a) 100mm Each 50
(b) 75mm Each 20
32
Providing and fixing M.S. stays and
clamps for sand cast iron/centrifugally
cast (spun) iron pipe of diameter:
(a) 100mm Each 7
(b) 75mm Each 1
33
Providing and fixing bend of required
degree with access door, insertion rubber
washer 3 mm thick, bolts and nuts
complete.100mmSand cast iron S&S as per IS - 3989 Each 19.00
75mmSand cast iron S&S as per IS - 3989 Each 2.00
34
Provding and fixing sand cast iron trap of
self cleansing design with sand cast iron
screwed down or hinged grating with or
without vent arm complete, including cost
of cutting and making good the wall and
floors.100mm inlet and 75mm outlet Sand cast iron S&S as per IS: 3989.Each 19.00
100mm inlet and 100mm outlet Sand cast iron S&S as per IS: 3989.Each 8.00
35 Providing and fixing collar
100mm Sand cast iron S&S as per IS - 3989Each 6
75mm Sand cast iron S&S as per IS - 3989 Each 1
36
Painting sand cast iron/centrifugally cast
(spun)soil, waste vent pipes and fittings
with paint of any colour such as match
with adjacent wall colour etc., over a coat
of primer (of approved quality) for new
work.100mm dia pipe Metre 135
75mm dia pipe Metre 30
37
Providing and fixing stainless steel kitchen
sink as per IS:13983 with C.I. Brackets and
stainless steel plug 40mm including
painting of fittings and brackets, cutting
and making good the walls wherever
required.Kitchen sink without drain board. 610x510
bowl depth 200mm Each 3
38
Providing and fixing P.V.C. waste pipe for
sink or wash basin including P.V.C. waste
fittings complete
40mm dia Flexible pipe Each 3
(III) Sub-Head-lll
C DRAINAGE
39
Providing and laying non -pressure NP2
class R.C.C. pipes with collars jointed with
stiff mixture of cement mortar in the
proportion of 1:2 including testing of joints
etc. 150 mm dia R.C.C. pipe Metr. 75.00
TOTAL SUB HEAD -ll
40
Constructing brick masonary manhole in
cement mortar 1:4 (1 cement, 4 coarse
sand.) R.C.C. top slab with1:2:4 mix(1
cement, 2 coars e sand, 4 graded stone
aggregate 20 mm nominal size) foundation
cocrete 1:4:8 mix (1cement, 4 coarse
sand, 8 graded stone aggregate 40 mm
nominal size.) inside plastering 12 mm
thick with cement mortar 1:3 (1 cement, 3
coarse sand.) finished with floating coat of
neat cement and making channels in
cement concrete 1:2:4. finished with
floating coat of neat cement complete as
per standard design.
(a)
Inside size 90x80cm and 45 cm deep
including C.I. cover with frame ( light duty)
455x610 mm internal diamension tatal
weight of cover and fram to be not less
than 38 kg (weight of cover23 kg and
weight of frame 15 kg )
With F.P.S. bricks with class designation
75Each 15.00
(b)
Inside size 120x90cm and 90 cm deep
including C.I. cover with frame (medium
duty) 500mm internal diameter total weight
of cover and fram to be not less than 116
kg (weight of cover 58kg and weight of
frame 58 kg )
With F.P.S. bricks with class designation
75Each 2.00
(IV) Sub-Head-lV(SEPTIC TANK
Septic tank( liquid dimension-4.8X1.8X1.5 cu-m) ,1 Nos.
41
Earthwork in excavation in foundation
trenches or drains including dressing of
sidesand ramming of bottoms,lift upto
1.5m,including getting out the excavated
soil and disposal of surplus excavated as
directed within a lead of 50m
All kind of soil Cum 59.20
42
Supplying and filling in plinth with local
sand and under floors including
watering,ramming consolidating and
dressing complete
Cum 2.38
43
Providing and laying in position concrete of
specified grade excluding the cost of
centring and shuttering all work upto plinth
level
441:2:4(1cement:2 corse sand:4 graded
stone aggregate 20mm nominal sizeCum 2.38
TOTAL SUB HEAD -lll
45
Brick work with bricks of class designation
100A in foundations and plinth in
Cement morter 1:6(1 cement : 6 corse
sand)Cum 10.72
46 12 mm cement plaster of mix
1:4(1 cement : 4 corse sand) Sqm. 100.61
47 Neat cement punning Sqm. 100.61
48
Brick on edge flooring bricks of class
designation 100a including cement slurry
etc. complete in cement morter
1:6(1 cement : 6 corse sand) Sqm. 16.56
49
Reinforced cement concrete work in
beams,suspended floors roofs,having
slope upto 15, landing,balconies,
shelves,chajjas,lintal,bends,plain window
sills stair case,and spiral staircases up to
floor five level excluding the cost of
centering,shuttering,finishing and
reinforcement with 1:2:4
Cum 3.38
50
Centring and shuttering including strutting
propping etc. and removal of form for
Suspended floors ,roofs,landings,balconies
and access platform Sqm. 15.28
51
Lintels,beams,plinth
bams,griders,bressumers and cantilivers Sqm. 2.25
52Columns,pillars,piers,abutments,posts and
strutsSqm. 6.00
53Supplying and fixing C.I cover without
frame for manholes:
500 mm diameter C.I cover (medium duty)
the weiht of he cover to be not less than 58
kg.
Each 2.00
54
Providing M.S foot rests including fixing in
septic tank with 20 x 20 x 10 cm cement
concrete blocks 1:3:6 ( 1 cement: 3 coarse
sand: 6 graded stone aggregate 20mm
nominal size) as per standard design:
With 20 x 20 mm square bar Each 18.00
55
Providing and fixing s.W intercepting trap
in manholes with stiff mixture of cement
mortar 1:1(1 cement: 1 fine sand) including
testing of joints etc. complete.
150 mm dia Each 2.00
(IV) Sub-Head-E
RAIN WATER PIPES AND FITTINGS
TOTAL SUB HEAD -lV
56
Providing and fixing on wall face
unplasticised Rigid PVC rain water pipes
conforming to IS:13592 Type A including
jointing with seal ring conforming to
IS:5382 leaving 10mm gap for thermal
expansion.(i) Single socketed pipes
(a) 110 mm diameter Meter 80
(b) 75 mm diameter Meter 20
57
Providing and fixing on wall face
unplasticised - PVC moulded
fittings/accessories for unplasticised Rigid
PVC rain water pipes conforming to
IS:13592 Type A including jointing with
seal ring conforming to IS: 5382 leaving
10mm gap for thermal expansion.
(i) Shoe (Plain)
(a) 110mm Shoe Each 8
(b) 75mm Shoe Each 6
(ii) Single Tee without door
(a) 75x75x75mm Each 14
(iii) Bend 87.5°
(a) 110mm Bend Each 8
(b) 75mm Bend Each 6
58
Providing and fixing unplasticised - PVC
pipe clips of approved design to
unplasticised - PVC rain water pipes by
means of 50 x 50 x 50mm hard wood
plugs, screwed with M.S. screws of
required length including cutting brick work
and fixing in cement mortar 1:4 (1 cement :
4 coarse sand) and making good the wall
etc. complete.(a) 110mm Each 44
(b) 75mm Each 13
59
Providing and fixing to the inlet mouth of
rain water pipe cast iron grating 15 cm
diameter and weighing not less than 440
grams.
Each 14
(V) Sub-Head-V
E WATER SUPPLY
TOTAL SUB HEAD -lV
60
Constructing masonry chamber 30x30x50
cm, inside with 75 class disignation brick
work in cement mortar 1:5 (1 cement :5
fine sand) for stop cock, with C.I. surface
box 100x100x75 mm with hinged cover
fixed in cement concrete slab 1:2:4 mix (1
cement :3 coarsesand :4 graded stone
aggregate 20 mm nominal size) necessary
sand :4 draded stone aggregate 20 mm
nominal :5 fine sand :10 graded stone
aggregate 40mm nominal size) and inside
plastering with cement mortar 1:3 (1
cement :3 coarse sand) 12 mm thick
finished with a floating coat of neat cement
complete as per standard disign.
With F.P.S. bricks Each 1.00
(VII) Sub-Head-Vl
G DRAINAGE
61
Making soak pit 2.5 m diameter 3.0 meter
deep with 45x45 cm dry brick honey comb
shaft with brick of class designation 75 and
S.W. drain pipe 100 mm diameter, 1.8 m
long complete as per standard design.
With F.P.S. bricks Each 1.00
62
Providing and fixing square mouth SW
gully trap grade A complete with CI grating
brick masonry chamber with water tight CI
cover with frame of 300X300mm
size(inside) the wt. of cover to be not less
than4.50kg. And frame to not less than
2.70 kg. as/standard design
150x100mmsize p type
With F.P.S. bricks designation 75 Each 1.00
63
Constructing brick masonry road gully
chamber 45X45X77.5 cm with bricks of
class designation 75 in cement mortar 1:4
including 500 X 450 mm pre cast RCC
vertical grating complete as per standard
designwith FPS bricks each 1
H SUB HEADVLL (TUBEWELL)
TOTAL SUB HEAD -Vl
TOTAL SUB HEAD -V
64
Providing all materials labour for drilling by
reverse Rotary rig machine for following
diameter of bore hole in all kinds of soil
mixed with kankar, sand and stone
including providing sample box and
collection strata sample of every 10'-0"
depth of drilling for accortaining proper
equiler for completing 300mmx200mm dia
high yielding tube well complete as per
P.H.E.D. spicifications
250 mm dia bore from 0 to 30 mtrs Mtrs. 30
250 mm dia bore from 30 to 60 mtrs Mtrs. 30
250 mm dia bore from 60 to 90 mtrs Mtrs. 30
250 mm dia bore from 90 to 120 mtrs Mtrs. 30
65
Supplying all materials such as following
sizes of PVC pipe with socket and
providing equipment and labour for
lowering the following pipe and cutting the
pipe to required size as per approved assly
and strata chart as required all complete
as per direction of E/I.
110 mm dia PVC. Pipe mtrs. Mtrs. 30
75 mm dia PVC. Pipe mtrs. Mtrs. 45
75 mm dia PVC.slotted Pipe mtrs. Mtrs. 30
66
Supplying the following fitting and fixing
the same in position as per approved
lowering assembly and strata chart
including providing all equipment on
process of lowering the assly etc.all
complete as per direction of E/I.
110X 75 mm dia PVC Reducer. Each 1
75 mm dia PVC. Well plug. Each 1
Solvent Cement. Kg 1
75 mm dia steed cap Each 1
GI wire 14 nos Kg 8
67
Supplying all materials labour and tools for
fitting tube well with pea graved of
dalbhumgarh of size 4 mm to 8 mm
including carriage, washing and placing
the same in position around the tube well
as per direction of E/I. Market Rate
cft 200
68
Supplying all equipments, tools and labour
and developing the tube well by air
compressor for continuous 8 hrs. till sand
free discharge of tube well as various
depth all complete as per direction of E/I.
Market Rate
Hrs 8
69
Transportation cost for rig machine and
other accessories materials and
equipments including development unit
etc. To tube well site till complete of work
and returning back etc. all
complete.Market rate
L.S. 1
70
Supplying all materials and labour for
arrangement for additional water required
during drilling period. Market rate.L.S. 1
71Establishment of -2HP of submersible
pump set (detail attchhed)each 1
SL No Description Unit Quantity Rate Amount
1 ROAD & PAVING WORK
Earth work in excavation by mechanical
means (Hydraulic excavator) / manual
means over areas (exceeding 30cm in
depth. 1.5m in width as well as 10 sqm on
plan) including disposal of excavated
earth, lead upto 50m and lift upto 1.5m,
disposed earth to be levelled and neatly
dressed.All kind of soil Cum 50.0
2 Filling available excavated earth (excluding
rock) in trenches, plinth, sides of
foundations etc. in layers not exceeding
20cm in depth, consolidating each
deposited layer by ramming and watering,
lead up to 50 m and lift upto 1.5 m.
All kind of soil cum 950.0
3 Banking excavated earth in layers not
exceeding 20 cm. in depth, reaking clods,
watering, rolling each layer with ½ tonne
roller, or wooden or steel rammers, and
rolling every 3rd and top-most layer with
power roller of minimum 8 tonnes and
dressing up, in embankments for roads,
flood banks, marginal banks, and guide
banks etc., lead upto 50 m and lift upto 1.5
m.All kind of soil cum 150
Total Vll
Total Sub head C -
CIVIL ITEMS SUB HEAD D (SITE DEVELOPMENT & BOUNDARY WALL)
4 Providing & laying in position cement
concrete of specified grade excluding the
cost of centring and shuttering -All works
upto plinth level:
1:3:6 (1 cement: 3 coarse sand: 6 graded
stone aggregate 20 mm nominal size) cum 8
5 Earth work in rough excavation , banking
excavated earth in layer notexceeding 20
cm in depth , breaking clods watering ,
rolling each layer with 1/2 tonne roller or
wooden or steel rammers and rolling every
3rd and top-most layer with power roller of
minimum 8 tonnes and dressing up in
embankments for roads, flood banks ,
marginal banks and guide banks or filling
up ground depressions. lead upto 50 m
and lift upto 1.5m.
All Kinds of soil cum 105
6 Construction of granular sub-base by
providing close graded Material
conforming to specifications, mixing in a
mechanical mix plant at OMC, carriage of
mixed material by tippers to work site, for
all leads & lifts, spreading in uniform layers
of specified thickness with motor grader on
prepared surface and compacting with
vibratory power roller to achieve the
desired density, complete as per
specifications and directions of Engineer-in-
Charge.With material conforming to Grade-
II (size range 53 mm to 0.075 mm ) having
CBR Value-25.
cum 8.25
7 Providing and laying 60mm thick factory
made cement concrete interlocking paver
block of M -30 grade of approved shape &
Size made by block making machine with
strong vibratory compaction and of
approved size and design/ shape laid in
required colour and pattern over and
including 50mm thick compacted bed of
course sand, filling the joints with coarse
sand etc. all complete as per the direction
of Engineer-in-charge.
Sqm 225
8 Providing and laying 60mm thick factory
made cement concrete interlocking grass
paver block of M 30 grade approved shape
& Size made by clock making machine
with strong vibratory compaction and of
approoved size and design/shape laid in
required colour & pattern over and
including 50mm thick compacted bed of
course sand, filling the joints with course
sand etc. all complete as per the direction
of Engineer-in-Charge
Sqm 400
9 Providing and faying cement concreate in
kerbs, steps and the like at or near ground
level excluding the cost of centring,
shuttering and finishing.
1:3:6 (1 Cement:3 coarse sand:6 graded
stone aggregate 20
mm nominal size)
cum 10
10 Brick work with bricks of class designation
100B in foundations and plinth in ::
Cement mortar 1:6 (1 cement : 6 coarse
sand)
Cum76
12 mm cement plaster of mix :1:6 (1
cement: 6 fine sand) sqm 142.5
Applying one coat of white cement primer
of approved brand and manufacture on
exterior wall surface:
sqm 57
Finishing walls with water proofing cement
paint(Snowcem) of approve brand and
manufacture and of required shade to give
an even shade new work (Three or more
coat).
sqm 57
TOTAL OF ROAD WORK CARRIED
OVER TO SUMMARY OF CIVIL WORKS
BOUNDARY WALL & GATE HOUSE
11 Earth work in excavation by mechanical
means (Hydraulic excavator) / manual
means in foundation trenches or drains
(not exceeding 1.5 m in width or 10 sqm on
plan) including dressing of sides and
ramming of bottoms, lift upto 1.5 m,
including getting out the excavated soil
and disposal of surplus excavated soil as
directed, within a lead of 50 m.
All kind of soil Cum 210
12 Filling available excavated earth (excluding
rock) in trenches, plinth, sides of
foundations etc. in layers not exceeding
20cm in depth, consolidating each
deposited layer by ramming and watering,
lead up to 50 m and lift upto 1.5 m.
Cum 120
13 Providing & laying in position cement
concrete of specified grade excluding the
cost of centring and shuttering -All works
upto plinth level:1:3:6 (1 cement: 3 coarse sand: 6 graded
stone aggregate 20 mm nominal size) cum 26
14 Providing and laying in position machine
batched and machine mixed design mix M-
25 grade cement concrete for reinforced
cement concrete work, using cement
content as per approved design mix,
including pumping of concrete to site of
laying but excluding the cost of centering,
shuttering, finishing and reinforcement,
including admixtures in recommended
proportions as per IS: 9103 to accelerate,
retard setting of concrete, improve
workability without impairing strength and
durability as per direction of Engineer-in-
charge.
(Note :- Cement content considered in this
item is @ 330 kg/cum. Excess/less cement
used as per design mix is
payable/recoverable separately).All works upto plinth level. cum 6.5
All works above plinth level upto Roof
Floor.cum 1.5
Walls columns, pillars, posts cind strutscum 11
Beams, planth beams, girders,
bressumers, contilevers,Suspended floors
lintels roofs and staircases includingspiral
staircases, shelves etc.
cum 27
15 Steel reinforcement for R.C.C. work
including straightening, cutting, bending,
placing in position and binding all complete
upto plinth level.Thermo-Mechanically Treated bars TMTC-
500-6mm dia.kg 510
Thermo-Mechanically Treated bars TMTC-
500-8mm dia.kg 800
Thermo-Mechanically Treated bars TMTC-
500-10mm dia.kg 1110
Thermo-Mechanically Treated bars TMTC-
500-12mm dia.kg 1050
16 Centering & shuttering including strutting,
propping etc.& removal of form (staging
height upto 4.2m) for:
Foundations, footings, bases of columns
etc. for mass concrete.sqm 325
Columns, pillars, piers, abutments, posts &
struts.sqm 276
Suspended floors, roofs, landings,
balconies & access plateform.sqm 15
Lintels, beams, plinth beams, girders,
bressumers & cantilevers.sqm 3
17 Brick work with common burnt clay F.P.S.
(non modular) bricks of class designation
7.5 in superstructure above plinth level up
to floor V level in all shapes and sizes in
:Cement mortar 1:6 (1 cement : 6 coarse
sand)
cum 98
18 Making plinth protection 50mm thick of
cement concrete 1:3:6 (1 cement :3 coarse
sand : 6 graded stone aggregate 20 mm
nominal size) over 75mm thick bed of dry
brick ballast 40 mm nominal size, well
rammed and consolidated and grouted
with fine sand including finishing the top
smooth
sqm 15
19 12 mm cement plaster of mix :1:6 (1
cement: 6 fine sand) sqm 1325
20 6 mm cement plaster of mix :1: 3 (1
cement: 3 fine sand)sqm 20
21 Brick Flat soiling :- Providing designation
100 B one brick flat soling joints filled with
local sand including cost of watering,
taxes, royalty all complete as per building
specification and direction of E/l,
sqm 15.0
22 P.C.C Flooring:- 40mm Th cement
concrete flooring 1:2:4(1Cement:2
Coarse:4 Grade stone aggregate)finished
with a floating coat of neat cement
including cement slurry etc.
sqm 15
23 Skirting :- 18mm Th Cement plaster
skirting (up to 15 Cm height) with cement
mortar 1:3(1Cement : 3 coarse sand )
finished with a floating coat of neat cement
.
sqm 8
24 Door chowkhat :-Providing and fixing
pressed steel door frame confirming IS
code 351 manufactured from commerical
mild steel sheet of 1.25 mm thickness
including hinges, jamb, lock jamb, bead
and if required angle threshold of mild
steel angle of section 50 x 25 mm or base
ties of 1.25mm pressed mild steel welded
or rigidly fixed together by . mechnical
means, adjustable lugs with split end tail to
each jamb including steel butt hinges 2.5
mm thick with mortar guards, lock strike-
plate and shock absorbers as specified
and applying a coat of approved steel
primer after pre-treatment of the surface as
directed by Engineer-in-charge:
Profile C
meter 5.5
25 Providing and fixing 1mm thick M.S. sheet
door with frame of 40x40x6mm angle iron
and 3mm M.S. gusset plates at the
junctions and corners, all necessary fittings
complete, including applying a priming
coat of approved steel primer.Using M.S.
angels 40x40x6 mm for diagonal braces.
sqm 2.1
26 Providing and fixing M.S. grills of
requirement pattern in frames of windows
etc. with M.S. flats bars 5mm Th & 20mm
wide or 10mm x 10mm square bars @
100mm C/C Vertical /horizontal etc.all
complete, fixed to openings/wooden
frames with rawl plugs screws etc.
kg 550
27 Steel glazed window :- Providing and
fixing steel glazed windows and ventilatrs
of standard rolled steel sections, joints
mitered and welded with 15x3 mm lugs 10
cm long with steel lugs embedded in
cement concrete blocks 15x10x10 cm of
1:3:6(1 cement: 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) or
with woodenplugs and screws or rawl
plugs and screws or with fixing clips or
with bolts and nuts as required, including
providing and fixing of glass panes with
glazing clips and special metal-sash putty
of approved make complete including
applying a priming coat of approved steel
primer; excluding the cost of metal beading
and other fitting except necessary hinges
or pivots as required.
Sqm 3
28 Providing and fixing M.S.fan clamp type 1
of 16 mm dia.M.S. bar bent to shape with
hooked ends in R.C.C slabs during laying
including painting the exposed portion of
loop,all as per standard design complete.
each 1
29 Providing and fixing circular cast iron box
for ceiling fan clamp 140 mm internal dia,
73 mm height, 5 mm thick rim bottom and
top lids, 1.5 mm thick M.S sheet with its
top surface hacked for proper bonding top
lid shall be screwed into the cast iron box
by means of 3.3 mm dia round headed
screws, one ;pcf at the corners. Clamps
shall be made of 12 mm dia M.S. bar bent
to shape as per standard drawing.
each 1
30 Applying one coat of white cement primer
of approved brand and manufacture on
exterior wall surface:
sqm 1350
31 Finishing walls with water proofing cement
paint(Snowcem) of approve brand and
manufacture and of required shade to give
an even shade new work (Three or more
coat).
sqm 1350
32 Distempering with dry distemper of
approved brand and manufacture
(Ashian/Berger/) two or more coats and of
required shade on new work ,over and
including primimn coat of whiting to given
an even shade.
sqm 30
33 With ready mixed zinc chromate yellow
primer of approved brand and manufacture
on steel galvanized iron/steel workssqm 15
34 Painting with synthetic enamel paint of
approved brand and manufacture with
enamel putty in all shades to give an even
shade New steel work (two or more coats)
sqm 15
35 Providing and fixing concertina coil fencing
with punched tape concertina coil 600 mm
dia 10 metre openable length ( total length
90 m) having 50 nos rounds per 6 metre
length, upto 3 m height of wall with existing
angle iron 'Y' shaped placed 2.4 m or 3.00
m apart and with 9 horizontal R.B.T.
reinforced barbed wire, stud tied with G.I.
staples and G.I. clips to retain horizontal
including necessary bolts or G.I. barbed
wire tied to angle iron all complete as per
direction of Engineer-in-charge with
reinforced barbed tape(R.B.T.) / Spring
core (2.5mm thick) wire of high tensile
strength of 165 kg/ sq.mm with tape (0.52
mm thick) and weight 43.478gm/ metre
(cost of M.S. angle, C.C. blocks shall be
paid separately)
Rmt 270
TOTAL OF BOUNDARY WALL & GATE
HOUSE WORK CARRIED OVER TO
SUMMARY OF CIVIL WORKS
TOTAL SUB HEAD (A+B+C+D)
SUMMARY
TOTAL CIVIL WORK (Building) Sub Head A
TOTAL SITE DEVELOPMENT & BOUNDARY WALL SUB HEAD -D
Grand total:-
Total Sub head D :-
TOTAL INTERNAL ELECTRICAL WORK SUB HEAD-B
Total Above
Grand total-
TOTAL P.H.E WORK SUB HEAD-C