Upload
ardikurniawan
View
63
Download
6
Embed Size (px)
Citation preview
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C1
page
FBC10
Frameless Balustrade Channel
Technical Considerations
• It is recommended that a level fi rm surface to be provided for fi xing of the channel
• Do not fi x channel to compressibledeck surfaces
• It is recommended that a suitably qualifi ed engineer is consulted to check on all installations.
• Fixing to structure should be a minimum of M10 x 100 stainless steel fi xing. Please consult an engineer to determine what fi xings are required based on type of structure the channel will be attached to.
Sizes & Finishes
• Available in 5.85 & 2.925 metre lengths• Mill fi nish or silver pearl• Can be cut to size and powdercoated
to colour of your choice
ImportantDue to the lime content of all cementatious non shrink grout, please note the following:
1. The FBC10 balustrade channel should not be used in either anodized or mill fi nish.
2. Powder coating of channel must include both the inside and outside of the product.
3. Grout must be carefully mixed in accordance with the manufacturers instructions as given on the bag. Wrongly mixed grout will increase the likelihood of corrosion of the channel.
Please see following page (C2) for test results
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
FBC10 Balustrade Channel Test Results
Non Shrink Grout
Typical Details
• Compressive strength:49 MPa @ 1 day62 MPa @ 7 days79 MPa @ 28 days
• Flexural strength:2.5 MPa @ 1 day9.0 MPa @ 7 days10.0 MPa @ 28 days
• Time for expansion:Start: 5 minutesFinish: 2 hours
• Fresh wet density approximately 2160 kg/cu.m depending on the consistency used
• Young’s Modulus: 25 GPa• Expansions characteristics:
An expansion of up to 1% overcomes shrinkage in plastic material
• Setting times:Initial: 165 minutes 20°Final: 270 minutes 20°
IMPORTANT: Grout must be mixed strictly in accordance with the manufacturers instructions on the bag. Incorrectly mixed grout can cause excessive corrosion.
FBC10 GROUT
Pool Fences• System can be used in applications where the
wind load is no greater than .58 KPa.• This is based on a total system height of 1200mm
including the channel (glass extends 1105mm fromthe top of the channel).
Note 1:
Panels must be greater than 1000mm wide.
Note 2:
The system cannot be used in applications where the area can be defi ned as one where people can congregate.
BalustradesResidential (excluding balconies)
• 10mm Toughened can be used to a maximum height of 620mm in applications, where the wind load does not exceed 1.8 KPa.
• 12mm Toughened can be used to a maximum height of 840mm in applications where the wind load does not exceed 1.37 KPa.
• In applications requiring 1000mm high balustrade, 15mm Toughened is to be used, but only to a maximum wind load of 1.12 KPa wind load.
BalustradesResidential (including balconies)
• 10mm Toughened can be used to a maximum height of 550mm in applications where the wind load does not exceed 2.5 KPa.
• 12mm Toughened can be used to a maximum height of 740mm in applications where the wind load does not exceed 1.9 KPa.
• In applications requiring 1000mm high balustrade, 15mm Toughened is to be used, but only to a maximum wind load of 1.37 KPa wind load.
Note 1:
The system is not recommended for use in any balustrade installations where fall on the other side is greater than 1 metre.
Note 2:
The above results have been generated by ARUP Facade Engineering. Physical testing has also been conducted by Compusoft Engineering in New Zealand. The results of both these are being collated in conjunction with the proposed changes listed in the latest draft of revisions for AS1288.
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C3
page
FBC20 (Driglaze)
Driglaze Balustrade Channel
Driglaze is the revolutionary new method for supporting 10, 12 and 15mm toughened glass for balustrades.
Driglaze eliminates the need for any grouting and therefore installation of balustrading is faster and cleaner than ever before. Driglaze offers the benefi t of adjustment up to 15mm vertically and angle adjustment of +/- 3°. Installation is also made easy by use of the coverplate simply being clipped on from the interior side. This will eliminate the requirement for scaffolding on certain sites and provide increased ease of installation. Channel is predrilled at 400mm centres for ease of installation.
This product not only boasts engineering function but also has clean lines to suit any style. Available in Silver Pearl marine grade powdercoated or mill fi nish, the product will suit all environments.
Product Specifi cations
• Standard for 10, 12 and 15mm glass with vertical adjustment up to 15mm
• Angle adjustment of +/- 3˚(+/- 50mm @ 1000mm high)(+/- 60mm @ 1200mm high)
• Base channel predrilled 14mm diameter holes at 400mm centres
Available Finishes
• Base and coverplate available in silver pearl or mill fi nish
• Powder coat is Anotec Silver Pearl with 10 year warranty
Please see following page (C4) for assembly instructions
Angle of adjustment up to +/- 3° to ensure all glass is vertical on sloping surfaces. +/- 50mm @ 1000mm high+/- 60mm @ 1200mm high
Marine grade, Silver Pearl powdercoated, with a 10 year warranty for coastal/harsh environments, or Special powdercoat finishes available to match client’s requirements.
10, 12 or 15 mm glass.
Up to 15mm vertical adjustment to attain a level height.
Built in weather strip for clean aesthetic lines.
Heavy duty clip on coverplate from the interior side for increased ease of installation.
Stainless adjustable screws for vertical adjustment.
Stainless Clamp Bolt.
Anodised clamping plate for maximum protection.
Base and coverplateavailable in Silver Pearl, Mill fi nish or powdercoated to your choice of colour.
Clamping assemblies available with all components included.
Predrilled holes at 400mm centres for ease of installation.
Rotating support for load carrying in various positions.
Stainless Pivot pin for anchoring the glass in place.
Wide anchoring base for maximum load holding.
-3o +3o
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Assembly Instructions1 Cut the channel to size and place in position as
required. Drill concrete slab at specifi ed centres and install threaded studs using Chemset in accordance with the manufacturer’s instructions.
2 M12 threaded stud to be drilled minimum 90mm into concrete when using Chemset (follow manufacturer’s instructions). This is a recommendation only. Please consult an engineer to determine most suitable fi xing method.
3 Insert Pivot Nuts into the channel prior to securing the channel to the slab.
4 Secure the channel to the concrete slab using M12 nuts and washers to a maximum height of 24mm above the substrate level. This is a recommendation only. Please consult an engineer to determine most suitable fi xing method.
5 Insert the weatherstrip into the base channel.6 Place setting blocks in the base channel to support
the glass while the clamps are placed on the glass. 7 Fix the clamping assembly and adjusting screws
around the glass and tighten to support the glass before fi nal adjustments are made.
8 Ensure that the two sections of the clamping assembly are assembled as per the diagram; the external section will hold the cover plate in place.
9 Place the glass with the clamping assemblies attached in place into the base section and line up the “pivot nuts” to go through the fi xing kits. Tighten the nuts loosely onto the pivot nuts to hold the glass in place.
10 Adjust the vertical height of the glass panels by moving the glass up and down as required with packers under the glass.
11 Tighten the “clamp nut” at both ends of the glass panel, just enough to hold glass in place.
12 Tighten the remaining clamps, checking for correct vertical and horizontal alignment and tighten all nuts.
13 Adjust the “adjusting screws” evenly around the glass panel and between ends of the glass panel, just enough to hold glass in place.
14 Fit the coverplate and end caps as required, placing the weatherstrip on the coverplate fi rst.
FBC20 Installation
Weatherstrip
BASE CHANNEL INSTALLATION
Weatherstrip
Pivot Nut
M12 Nut
Max 24mm
90mm100mm
Base Channel Installation CLAMPING ASSEMBLY
Rubber Spacer
R3 to indicate top
AdjustingScrews
COVERPLATE SIDEINTERNAL SIDE
Clamping Assembly FINISHED COMPONENT
Clamp Nut
Clamp platesetting block
Finished Component
FBC20 Wind load Test Results
Residential Balustrade (Internal) and Pool Fencing
Residential Balustrade (External) and General
Offi ce (non retail)
Public Areas - Retail without crowd loading
Maximum Panel Widths (mm)
No. Of ClampsPer Panel
No. Of ClampsPer Panel
No. Of ClampsPer Panel
500 2 2 2501 – 600 2 2 2601 – 700 3 3 3701 – 800 3 3 3801 – 900 3 3 3
901 – 1000 3 3 31001 – 1100 3 4 41101 – 1200 4 4 41201 – 1300 4 4 41301 – 1400 4 5 51401 – 1500 4 5 51501 – 1600 4 5 51601 – 1700 5 5 51701 – 1800 5 6 61801 – 1900 5 6 61901 – 2000 5 6 6
Design Criteria
Residential Balustrade (Internal) and Pool Fencing
Minimum Glass Thickness: 12mm Toughened or 13.52 Toughened Laminate (up to 1200mm high)Maximum Load Capacity: up to 0.75kn/m, or 0.6kn point loadMaximum Windload: up to 1.5kPa
Residential Balustrade (External) and General Offi ce Balustrade (non retail)
Minimum Glass Thickness: 12mm Toughened or 13.52 Toughened Laminate (1200mm high)Maximum Load Capacity: up to 0.75kn/m, or 0.6kn point loadMaximum Windload: up to 1.5kPa
Public Areas - (Retail without crowd loading)
Minimum Glass Thickness: 15mm Toughened or 17.52 Toughened Laminate (1200mm high)Maximum Load Capacity: up to 1.5kn/m (or 1.5kn point load)Maximum Windload: up to 1.5kPa
Positioning of clamps: Clamps at either end of panel to be no further then 50mm into centre of glass notch.
Certifi ed by Peter Darcy & Co PTY LTD
25
25 for 10 & 12mm glass
50 max
12 Channel13 min/28 maxdepending on size of setting block
45
Note: Not to scale
30
30 for 15mm glass
50 max
12 Channel13 min/28 maxdepending on size of setting block
45
Note: Not to scale
Glass Notch Detail
H1 Height Required minus 25mm from fi nished fl oor level
H2 55mmW1 Please refer to table on C5, this will depend
on glass widths and area type of installationW2 12mm Glass=25mm
15mm Glass=30mm
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C5
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Universal Mini PostsBase Mounted, Square Mini PostFriction Fit
Technical Details
• No holes in glass required• 316 Grade Stainless Steel• Suitable for 12mm glass and 15mm glass• Supplied with dress ring to conceal
structural fi ttings• For details on custom designs and
sizes please contact sales supporton (03) 8562 0888
Available Finishes
• Polished stainless steel• Satin stainless steel
Specify at time of order• Finish required
Installation Instructions1 Determine appropriate glass sizes by
referencing the Pool Fence Guide on the page C7C or referring to a suitably qualifi ed engineer for use in balustrades.
2 Fix mini post to structure in desired location using suitable fi xing method. 3 Install glass into mini post, place cover plate on and secure by tightening 2 x M10 grub screws onto fl at clamping plate.4. Final adjustment as required and then re check all screws are tight.
Note: For concrete decks we suggest HILTI HVU+HIS-RN M10 or equivalent anchors.
As construction of timber decks vary infi nitely, we recommend consultation by a suitably qualifi ed engineer to certify appropriate use in each application.
Installers should check with anchor manufactures for minimum distance from the slab edge.
A
A
175
120
12
25
75
168
7
Ø114
50 50
Ø10.5
Ø10.5
14
R5.25
14
R5.25
61.39
61.39
24.5
C6page
UPDATE 04/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
FMP BM SQ FF
© Copyright 2011 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Universal Mini Posts Base Mounted, Square Mini PostMechanical Fix
Technical Details
• 316 Grade Stainless Steel• Suitable for 12mm glass and 15mm glass• Supplied with dress ring to conceal
structural fi ttings• For details on custom designs and
sizes please contact sales supporton (03) 8562 0888
Available Finishes
• Polished stainless steel• Satin stainless steel
Specify at time of order• Finish required
Installation Instructions1 Determine appropriate glass sizes by
referencing the Pool Fence Guide on the page C7C or referring to a suitably qualifi ed engineer for use in balustrades.
2 Fix mini post to structure in desired location using suitable fi xing method. 3 Install glass into mini post, place cover plate on and insert and tighten the M10 CSK bolt through the mini post.4. Final adjustment as required and then re check all screws are tight.
Note: For concrete decks we suggest HILTI HVU+HIS-RN M10 or equivalent anchors.
As construction of timber decks vary infi nitely, we recommend consultation by a suitably qualifi ed engineer to certify appropriate use in each application.
Installers should check with anchor manufactures for minimum distance from the slab edge.
© Copyright 2011 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
UPDATE 04/11
C7page
FMP BM SQ HG
A
A
175
120
65
20
Ø114
Ø10.5
Ø10.50
14
14
R5.25
R5.25
61.39
61.39
168
7
50 50
24.5
87.5
55
12
65
Ø 20
© Copyright 2011 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Universal Mini Posts Base Mounted, Round Mini PostFriction Fit
Technical Details
• No holes in glass required• 316 Grade Stainless Steel• Suitable for 12mm glass• Supplied with dress ring to conceal
structural fi ttings• For details on custom designs and
sizes please contact sales supporton (03) 8562 0888
Available Finishes
• Polished stainless steel• Satin stainless steel
Specify at time of order• Finish required
Installation Instructions1 Determine appropriate glass sizes by
referencing the Pool Fence Guide on the page C7C or referring to a suitably qualifi ed engineer for use in balustrades.
2 Fix mini post to structure in desired location using suitable fi xing method. 3 Install glass into mini post, place cover plate on and secure by tightening 2 x M10 grub screws onto fl at clamping plate.4. Final adjustment as required and then re check all screws are tight.
Note: For concrete decks we suggest HILTI HVU+HIS-RN M10 or equivalent anchors.
As construction of timber decks vary infi nitely, we recommend consultation by a suitably qualifi ed engineer to certify appropriate use in each application.
Installers should check with anchor manufactures for minimum distance from the slab edge.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
FMP BM RD FF
C7Apage
UPDATE 04/11
A
A
120
12
25
75
46.87
24.5
175
Ø114
Ø10.5
Ø10.5 R5.25
R5.2
5
14
14
61.39
61.39
168
50Ø
7
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
UPDATE 04/11
C7Bpagepage
Universal Mini Posts Base Mounted, Round Mini PostMechanical Fix
Technical Details
• 316 Grade Stainless Steel• Suitable for 12mm glass and 15mm glass• Supplied with dress ring to conceal
structural fi ttings• For details on custom designs and
sizes please contact sales supporton (03) 8562 0888
Available Finishes
• Polished stainless steel• Satin stainless steel
Specify at time of order• Finish required
Installation Instructions1 Determine appropriate glass sizes by
referencing the Pool Fence Guide on the page C7C or referring to a suitably qualifi ed engineer for use in balustrades.
2 Fix mini post to structure in desired location using suitable fi xing method. 3 Install glass into mini post, place cover plate on and insert and tighten the M10 CSK bolt through the mini post.4. Final adjustment as required and then re check all screws are tight.
Note: For concrete decks we suggest HILTI HVU+HIS-RN M10 or equivalent anchors.
As construction of timber decks vary infi nitely, we recommend consultation by a suitably qualifi ed engineer to certify appropriate use in each application.
Installers should check with anchor manufactures for minimum distance from the slab edge.
© Copyright 2011 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
FMP BM RD HG
A
A
Ø10.5
Ø10.5
R5 .25
Ø114
175
24.5
87.5
55
61.
.
R525.
39
61.39
Ø 5012
120
168
7
65
Ø 20
© Copyright 2011 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
UPDATE 04/11
Universal Mini Post Recommended Panel Sizes
BalustradesUse of the Universal Mini Post in balustrade applications will be dependent on several factors including type of balustrade and environmental conditions. We recommend consultation by a suitably qualifi ed engineer to determine suitability on a job by job basis.
Pool fencing (Concrete Applications Only)The following tables can be used to determine maximum panel size for each wind pressure. Please note this usage table is based on using HILTI HVU+HIS-RN M10 to a depth of 110mm.
Wind pressure kPa
Posts Per
Panel
Post
Type
(See legend below)
0.8 kPa 1.0 kPa 1.5 kPa 2.0 kPa 2.5 kPa
Max (A)
mm
Max (B)
mm
Max (A)
mm
Max (B)
mm
Max (A)
mm
Max (B)
mm
Max (A)
mm
Max (B)
mm
Max (A)
mm
Max (B)
mm
12mm Toughened Safety Glass
Toughened Safety Glass
(AS/NZS 2208) 2 1, 2, 3, 4 1000 1400 750 1150 400 800 200 600 N/A N/A
Toughened Safety Glass
(AS/NZS 2208) 3 1, 2, 4 800 2000 600 1600 300 1000 200 800 N/A N/A
15mm Toughened Safety Glass
Toughened Safety Glass
(AS/NZS 2208) 2 1, 2, 4 1500 1900 1100 1500 600 1000 400 800 200 600
Toughened Safety Glass
(AS/NZS 2208) 3 1, 2, 4 950 2300 750 1900 500 1400 400 1200 300 1000
ULS Wind Pressure Regions
0.8 kPa (Region A2, TC 3) NSW, ACT, VIC, SA, WA (Sth of Green Head), Interior QLD & NT - Suburban
1.0 kPa (Region A2, TC 2) NSW, ACT, VIC, SA, WA (Sth of Green Head) - Coastal & Open Terrain; Interior QLD & NT - Open Terrain
1.5 kPa (Region B, TC 3) QLD South of Bundaberg - Suburban
2.0 kPa (Region B, TC 2) QLD South of Bundaberg - Coastal / Exposed
2.5 kPa (Region C) QLD (North of Bundaberg), NT Coastal
All Mini Posts are SS316Tabulated values are based on design stresses limited by either the glass or mini-posts and/or defl ection. Values also based on M10 anchor base fi xing into non-crack concrete.
Legend
Post Type 1: FMP BM SQ FF - Base Mount, Square, Friction Fit Post Type 2: FMP BM SQ HG - Base Mount, Square, Mechanical Fix Post Type 3: FMP BM RD FF - Base Mount, Round, Friction Fit ** Post Type 4: FMP BM RD HG - Base Mount, Round, Mechanical Fix
**Note: Post Type 3: Round - Friction Fit - Mini Post is temporarily excluded from 12mm glass with 3 posts and all 15mm glass combinations pending test data analysis.
Note: These calculations are based on using Fethers fi ttings and do not apply to fi ttings supplied by others.
1150
2 Posts Per Panel 3 Posts Per Panel
Base Mounted Mini Post
75-77 Ricketts Rd, Mt Waverley VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C8
page
Universal Mini PostsCore Drilled, Square Mini PostFriction Fit
Technical Details
• No holes in glass required• 316 Grade Stainless Steel• Suitable for 12mm glass• Supplied with dress ring to conceal core
drilling and M16 threaded rod for height adjustment
• For details on custom designs andsizes please contact sales supporton (03) 8562 0888
Available Finishes
• Polished stainless steel• Satin stainless steel
Specify at time of order• Finish required
Installation Instructions1 Determine appropriate glass sizes by
referencing the Pool Fence Guide on the following page or referring to a suitably qualifi ed engineer for use in balustrades.
2 Core drill holes and fi x mini post into position using suitable fi xing method.
3 Place dress ring over post and into position at base of post.4 Insert glass and tighten via M8 Grub screws5. Ensure all panels are plumb and securely braced.
Note: As constructions of timber and concrete decks vary infi nitely, we recommend consultation by a suitably qualifi ed engineer to certify appropriate use in each application.
A
A
240
70
50
350
150
120
12
50
50
Ø100
25
75
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
FMP CD SQ FF
UPDATE 11/10
C8Apage
Universal Mini Posts Core Drilled, Square Mini PostMechanical Fix
Technical Details
• 316 Grade Stainless Steel• Suitable for 12mm and 15mm glass• Supplied with dress ring to conceal core
drilling and M16 threaded rod for height adjustment
• For details on custom designs andsizes please contact sales supporton (03) 8562 0888
Available Finishes
• Polished stainless steel• Satin stainless steel
Specify at time of order• Finish required
Installation Instructions1 Determine appropriate glass sizes by
referencing the Pool Fence Guide on the following page or referring to a suitably qualifi ed engineer for use in balustrades.
2 Core drill holes and fi x mini post into position using suitable fi xing method.
3 Place dress ring over post and into position at base of post.4 Insert glass and tighten into position via M10 CSK Bolt5. Ensure all panels are plumb and securely braced.
Note: As constructions of timber and concrete decks vary infi nitely, we recommend consultation by a suitably qualifi ed engineer to certify appropriate use in each application.
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
UPDATE 11/10
C8Bpage
FMP CD SQ HG
A
A
350
150
120
12
65
(55)
17.5
160
50
20
70
50
65
Ø 20
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Universal Mini Posts Core Drilled, Round Mini PostFriction Fit
Technical Details
• No holes in glass required• 316 Grade Stainless Steel• Suitable for 12mm glass• Supplied with dress ring to conceal core
drilling and M16 threaded rod for height adjustment
• For details on custom designs andsizes please contact sales supporton (03) 8562 0888
Available Finishes
• Polished stainless steel• Satin stainless steel
Specify at time of order• Finish required
Installation Instructions1 Determine appropriate glass sizes by
referencing the Pool Fence Guide on the following page or referring to a suitably qualifi ed engineer for use in balustrades.
2 Core drill holes and fi x mini post into position using suitable fi xing method.
3 Place dress ring over post and into position at base of post.4 Insert glass and tighten via M8 Grub screws5. Ensure all panels are plumb and securely braced.
Note: As constructions of timber and concrete decks vary infi nitely, we recommend consultation by a suitably qualifi ed engineer to certify appropriate use in each application.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
FMP CD RD FF
C8cpage
UPDATE 11/10
A
A
240
360
120
12.5
Ø50
Ø100
160
25
75
46.87
70
50
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
UPDATE 11/10
C8Dpagepage
Universal Mini Posts Core Drilled, Round Mini PostMechanical Fix
Technical Details
• 316 Grade Stainless Steel• Suitable for 12mm and 15mm glass• Supplied with dress ring to conceal core
drilling and M16 threaded rod for height adjustment
• For details on custom designs andsizes please contact sales supporton (03) 8562 0888
Available Finishes
• Polished stainless steel• Satin stainless steel
Specify at time of order• Finish required
Installation Instructions1 Determine appropriate glass sizes by
referencing the Pool Fence Guide on the following page or referring to a suitably qualifi ed engineer for use in balustrades.
2 Core drill holes and fi x mini post into position using suitable fi xing method.
3 Place dress ring over post and into position at base of post.4 Insert glass and tighten into position via M10 CSK Bolt5. Ensure all panels are plumb and securely braced.
Note: As constructions of timber and concrete decks vary infi nitely, we recommend consultation by a suitably qualifi ed engineer to certify appropriate use in each application.
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
FMP CD RD HG
A
A
240
360
Ø50
Ø100
120
160
12.5
160
87.5
55
70
50
65
Ø 20
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
UPDATE 11/10
C8Epage
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BalustradesUse of the Universal Mini Post in balustrade applications will be dependent on several factors including type of balustrade and environmental conditions. We recommend consultation by a suitably qualifi ed engineer to determine suitability on a job by job basis.
Pool fencingThe following tables can be used to determine maximum panel size for each wind pressure:
Wind pressure kPaPosts Per
Panel
Post
Type
(See legend below)
0.8 kPa 1.0 kPa 1.5 kPa 2.0 kPa 2.5 kPa
Max (A)
mm
Max (B)
mm
Max (A)
mm
Max (B)
mm
Max (A)
mm
Max (B)
mm
Max (A)
mm
Max (B)
mm
Max (A)
mm
Max (B)
mm
12mm Toughened safety glass
Toughened Safety Glass
(AS/NZS 2208) 2 1, 2, 3, 4 1000 1400 750 1150 400 800 200 600 N/A N/A
Toughened Safety Glass
(AS/NZS 2208) 3 1, 2, 4 800 2000 600 1600 300 1000 200 800 N/A N/A
15mm Toughened safety glass
Toughened Safety Glass
(AS/NZS 2208) 2 1, 2, 4 1700 2100 1300 1700 800 1200 500 900 350 750
Toughened Safety Glass
(AS/NZS 2208) 3 1, 2, 4 1300 3000 1100 2600 600 1600 400 1200 300 1000
ULS Wind Pressure Regions
0.8 kPa (Region A2, TC 3) NSW, ACT, VIC, SA, WA (South of Green Head), Interior QLD & NT - Suburban1.0 kPa (Region A2, TC 2) NSW, ACT, VIC, SA, WA (South of Green Head) - Coastal & Open Terrain; Interior QLD & NT - Open Terrain1.5 kPa (Region B, TC 3) QLD South of Bundaberg - Suburban2.0 kPa (Region B, TC 2) QLD South of Bundaberg - Coastal / Exposed2.5 kPa (Region C) QLD (North of Bundaberg), NT Coastal
All Mini Posts are SS316Tabulated values are based on design stresses limited by either the glass or mini-posts and/or defl ection.
Legend
Post Type 1: FMP CD SQ FF - Core Drill, Square, Friction Fit Post Type 2: FMP CD SQ HQ - Core Drill, Square, Mechanical Fix Post Type 3: FMP CD RD FF - Core Drill, Round, Friction Fit ** Post Type 4: FMP CD RD HG - Core Drill, Round, Mechanical Fix
**Note: Post Type 3: Round - Friction Fit - Mini Post is temporarily excluded from 12mm glass with 3 posts and all 15mm glass combinations pending test data analysis.
Note: These calculations are based on using Fethers fi ttings and do not apply to fi ttings supplied by others.
1150
2 Posts Per Panel 3 Posts Per Panel
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Core Drilled Mini Post
Universal Mini Post Recommended Panel Sizes
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C9
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Balustrade Brackets To Suit Square & Round Posts
Technical Details
• All 316 grade stainless steel suitable for 8, 10 and 12mm glass with gaskets to suit each glass thickness in every box
• Confi gurations:• FBF2100 & FBF2600:
Designed to suit 50mm diameter round posts
• FBF2000 & FBF2500:Designed to suit square posts
Please Note: Bracket is supplied with additional pin for extra fi xing strength. Use of the pin requires hole in the glass.
Available Finishes
• Satin stainless steel• Polished stainless steel
Specify at time of order• Finish required
See followingpage for glass widths and wind loads
FBF 2000 Series
18/2018/20
FBF2000
FBF2100
FBF2500
FBF2600
24
Ø13
18/20
GLASS DETAILTo be used in pin applications
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
FBF 2000 Series Glass Widths & Wind loads
Use the following guide charts to determine the recommended glass sizes.
Residential Applications
Allowable glass spans in mm
No. fi ttings
Glass thickness
Design wind Pressure (kPa) - Widths of Panels (mm)
0.5 0.6 0.7 0.8 0.9 1.0 1.25 1.5 1.75 2.0 2.5
4 8mm 1450 1450 1450 1420 1380 1310 1200 1150 1080 1040 960
4 10mm 1950 1950 1850 1760 1700 1640 1520 1430 1350 1300 1200
6 8mm 1450 1450 1450 1420 1380 1380 1380 1380 1200 1100 1050
6 10mm 2100 2100 2100 2100 2100 2100 1800 1800 1600 1500 1400
8 8mm 2200 2200 2200 2200 2200 2200 2200 2200 2200 1970 1570
8 10mm 2400 2400 2400 2400 2400 2400 2400 2400 2400 2400 2080
Residential applications based on the following criteria:
• Handrail Loads - Concentrated 600N / Distributed 400N/m• Wind pressure - 0.5kPa• Defl ection limit - Span/90• Height of glass - 950mm• Glass type - Grade A Toughened glass to AS1288/06 and AS2208
Note: • For internal applications use design wind pressure = 0.5(kPa) column• These calculations are based on using Fethers fi ttings and do not apply to fi ttings supplied by others.
Commercial Applications
Allowable glass spans in mm
No. fi ttings
Glass thickness
Design wind Pressure (kPa) - Widths of Panels (mm)
0.5 0.6 0.7 0.8 0.9 1.0 1.25 1.5 1.75 2.0 2.5
4 8mm 1420 1420 1420 1420 1380 1310 1200 1150 1080 1040 960
4 10mm 1770 1770 1770 1760 1700 1640 1520 1430 1350 1300 1200
6 8mm 1420 1420 1420 1420 1380 1380 1380 1380 1200 1100 1050
6 10mm 1800 1800 1800 1800 1800 1800 1800 1800 1600 1500 1400
8 8mm 2200 2200 2200 2200 2200 2200 2200 2200 2200 1970 1570
8 10mm 2400 2400 2400 2400 2400 2400 2400 2400 2400 2400 2080
Commercial Applications Based On The Following Criteria:
• Handrail Loads - Concentrated 600N / Distributed 750N/m• Wind pressure - 0.5kPa-2.5kPa• Defl ection limit - Span/90• Height of glass - 950mm• Glass type - Grade A Toughened glass to AS1288 and AS2208
Note: • For internal applications use design wind pressure = 0.5(kPa) column• These calculations are based on using Fethers fi ttings and do not apply to fi ttings supplied by others.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C11
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Balustrade ClampMechanical Fixing Through Glass
Technical Details
• Used in balustrades and pool fencing where mechanical fi xing through glass is required.
• Suitable for 8mm, 10mm glass• Can be adopted to suit 6mm glass.
Please specify at time of order• Provides concealed fi xing to posts
and substrates• Requires 18mm hole in glass
Note: Fixings are not supplied with the clamp
Available Finishes
• Satin stainless steel• Polished stainless steel
Specify at time of order• Finish required
FBF4000
35
25
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Glass Anchor
Standard Button Head
Technical Details
• Supplied as standard in 316 grade satin stainless steel
• Suitable for 6mm, 8mm, 10mmand 12mm glass
• Custom sizes and styles available on request
• Other fi nishes available include polished stainless steel, 24k gold or powdercoat
Specify at time of order• Finish required• Code from table below
Code Diameter Body length Thread Hole in glass
GA19/10 SSS 19mm 10mm M6 10mm
GA19/20 SSS 19mm 20mm M6 10mm
GA19/30 SSS 19mm 30mm M6 10mm
GA25/20 SSS 25mm 20mm M6 10mm
GA25/30 SSS 25mm 30mm M6 10mm
GA25/50 SSS 25mm 50mm M6 10mm
GA32/20 SSS 32mm 20mm M10 14mm
GA32/30 SSS 32mm 30mm M10 14mm
GA32/50 SSS 32mm 50mm M10 14mm
Fixing options for standard button head anchors
Nut & washer Lag ScrewHollow wall (M6 only)
Timber insert Masonry
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C13
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Counter Sunk Head
Technical Details
• Supplied as standard in 316 gradesatin stainless steel
• Suitable for 6mm, 8mm, 10mmand 12mm glass
• Custom sizes and styles available on request
• Other fi nishes available include polished stainless steel, 24k gold or powdercoat
Specify at time of order• Finish required• Code from table below
Glass Anchor
Code Diameter Body length Thread Dimension A Dimension B
GA19/10 CSK-SSS 19mm 10mm M6 18mm 10mm
GA19/20 CSK-SSS 19mm 20mm M6 18mm 10mm
GA19/30 CSK-SSS 19mm 30mm M6 18mm 10mm
GA25/20 CSK-SSS 25mm 20mm M6 18mm 10mm
GA25/30 CSK-SSS 25mm 30mm M6 18mm 10mm
GA25/50 CSK-SSS 25mm 50mm M6 18mm 10mm
GA32/20 CSK-SSS 32mm 20mm M10 24mm 16mm
GA32/30 CSK-SSS 32mm 30mm M10 24mm 16mm
GA32/50 CSK-SSS 32mm 50mm M10 24mm 16mm
Fixing options for standard button head anchors
Nut & washer Lag ScrewHollow wall (M6 only)
Timber insert Masonry
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Counter Sunk Head With Cap
Technical Details
• Supplied as standard in 316 gradesatin stainless steel
• Suitable for 6mm, 8mm, 10mmand 12mm glass
• Custom sizes and styles availableon request
• Other fi nishes available include polished stainless steel, 24k gold or powdercoat
Specify at time of order• Finish required• Code from table below
Glass Anchor
Code Diameter Body length Thread Dimension A Dimension B
GA19/10 CAP-SSS 19mm 10mm M6 22mm 10mm
GA19/20 CAP-SSS 19mm 20mm M6 22mm 10mm
GA19/30 CAP-SSS 19mm 30mm M6 22mm 10mm
GA25/20 CAP-SSS 25mm 20mm M6 22mm 10mm
GA25/30 CAP-SSS 25mm 30mm M6 22mm 10mm
GA25/50 CAP-SSS 25mm 50mm M6 22mm 10mm
GA32/20 CAP-SSS 32mm 20mm M10 30mm 18mm
GA32/30 CAP-SSS 32mm 30mm M10 30mm 18mm
GA32/50 CAP-SSS 32mm 50mm M10 30mm 18mm
Fixing options for standard button head anchors
Nut & washer Lag ScrewHollow wall (M6 only)
Timber insert Masonry
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C15
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF1000
Glass Anchor
How the Product Code works
BF1000-50/10
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Spacer options 10, 15, 20, 30 and 50mm• Suitable for 10, 12, 15, and 19mm glass• M12 Threaded rod as standard• Can supply lag screws, timber inserts or
masonry fi xings if required
Specify at time of order• Finish required• Diameter & Spacer options:
• BF1000-38/10 • BF1000-50/10• BF1000-38/15 • BF1000-50/15• BF1000-38/20 • BF1000-50/20• BF1000-38/30 • BF1000-50/30• BF1000-38/50 • BF1000-50/50
• Rod and fi xing type
Product Diameter Spacer
UPDATE 02/11
Adjustable Glass Anchor
How the Product Code works
BFA1000-50/20
Technical Details
• 316 grade satin stainless steel fi nish• Spacer options; - 50mm diameter: 20-25mm and 40-45mm - 35mm diameter: 30-35mm and 45-50mm• Suitable for 10mm, 12mm and 15mm glass• Glass hole required; - 35mm diameter: 28mm - 50mm diameter: 34mm • Easy adjustment from centre, after installation of glass• Single gasket suitable for various glass thicknesses.
Available Finishes
• Polished Stainless Steel• Satin Stainless Steel
Specify at time of order• Finish required• Diameter & Spacer options: • BFA1000-35/30 • BFA1000-35/45 • BFA1000-50/20 • BFA1000-50/40
Product Diameter Spacer
30-35
Adjustment via two piece body
Adjustment via two piece body
Ø35
45-50
Ø35
Ø30
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BFA1000 50/20
UPDATED 08/10
20-25
Adjustment via two piece body
Adjustment via two piece body
Ø50
40-45
Ø50
Ø36
BFA1000-35/30 BFA1000-35/45
BFA1000-50/20 BFA1000-50/40
75-77 Rickett Rd, Mt Waverley, VIC 3170Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] A
page
BFA1000 Adjustable
75-77 Rickett Rd, Mt Waverley, VIC 3170Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C15 B
page
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF1100
Glass Anchor
How the Product Code works
BF1100-50/10
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Spacer options 10, 15, 20, 30 and 50mm• Suitable for 10, 12, 15, and 19mm glass• M12 Threaded rod as standard• Can supply lag screws, timber inserts or
masonry fi xings if required
Specify at time of order• Finish required• Diameter & Spacer options:
• BF1100-38/10 • BF1100-50/10• BF1100-38/15 • BF1100-50/15• BF1100-38/20 • BF1100-50/20• BF1100-38/30 • BF1100-50/30• BF1100-38/50 • BF1100-50/50
• Rod and fi xing type
Product Diameter Spacer
UPDATE 02/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C17
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF1150
Glass Anchor
How the Product Code works
BF1150-50/10
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Spacer options 10, 15, 20, 30 and 50mm• Suitable for 10, 12, 15, and 19mm glass• Glass hole required is 24mm diameter• M12 Threaded rod as standard• Can supply lag screws, timber inserts or
masonry fi xings if required
Specify at time of order• Finish required• Diameter & Spacer options:
• BF1150-38/10 • BF1150-50/10• BF1150-38/15 • BF1150-50/15• BF1150-38/20 • BF1150-50/20• BF1150-38/30 • BF1150-50/30• BF1150-38/50 • BF1150-50/50
• Rod and fi xing type
Product Diameter Spacer
PLEASE NOTE LARGER HOLE REQUIRED
UPDATE 02/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF1200
Handrail Fixing
BF1200-38For 38mm diameter
BF1200-50For 50mm diameter
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Suitable for mounting handrails to the glass panel
• Suitable for 10, 12, 15, and 19mm glass• Saddles (fl at & curved) can be supplied
loose or welded on to upright if required. Please specify if required.
Specify at time of order• Finish required• Flat or curved saddle (welded or loose)• Confi guration:
• BF1200-38• BF1200-50
UPDATE 02/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C19
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF1300
Handrail Fixing
BF1300-38For 38mm diameter
BF1300-50For 50mm diameter
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Suitable for mounting handrails to the glass panel
• Suitable for 10, 12, 15, and 19mm glass• Saddles (fl at & curved) can be supplied
loose or welded on to upright if required. Please specify if required.
Specify at time of order• Finish required• Flat or curved saddle (welded or loose)• Confi guration:
• BF1300-38• BF1300-50
UPDATE 02/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF1400
Post Attachment
BF1400-38For 38mm diameter
BF1400-50For 50mm diameter
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Designed to be welded to a vertical post to attach the glass panels
• Suitable for 10, 12, 15, and 19mm glass• Can also be used to mount handrails
to glass. Saddles (fl at & curved) can be supplied loose or welded on to upright if required. Please specify if required.
Specify at time of order• Finish required• Flat or curved saddle (welded or loose)• Confi guration:
• BF1400-38• BF1400-50
UPDATE 02/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C21
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF1500
Post Attachment
BF1500-38For 38mm diameter
BF1500-50For 50mm diameter
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Designed to be welded to a vertical post to attach the glass panels
• Suitable for 10, 12, 15, and 19mm glass• Can also be used to mount handrails
to glass. Saddles (fl at & curved) can be supplied loose or welded on to upright if required. Please specify if required.
Specify at time of order• Finish required• Flat or curved saddle (welded or loose)• Confi guration:
• BF1500-38• BF1500-50
UPDATE 02/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
Post Attachment
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Long fi xing leg can be cut to size to suit any application including staircases
Specify at time of order• Finish required• Long or short leg
BF1600
UPDATE 02/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C23
page
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF1700
Post Attachment
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Spacer options 10 and 15mm• Long fi xing leg can be cut to size to suit
any application including staircases
Specify at time of order• Finish required• Long or short leg
UPDATE 02/11
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
BF300 BF310
BF500 & BF500SP
Flat Cover
Technical Details
• 316 grade stainless steel• Also available as split rings• 90mm diameter ring with 51mm hole
Available Finishes
• Satin stainless steel• Polished stainless steel
Specify at time of order• Finish required• BF500• BF500SP
Top & Bottom Patch
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• BF300 with base fi tting• BF310 for top mounting• Gaskets are not supplied with
these fi ttings
Specify at time of order• Finish required• BF300• BF310
BF300 & BF310
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF500
BF500 BF500SP
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C25
page
BF610
Tapered Nut
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Available Sizes:
• 38mm Spacer – BF610-38• 50mm Spacer – BF610-50
Specify at time of order• Finish required• Size
BF600
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
38mm or 50mm Diameter Spacer.
How the Product Code works
BF600-50/10
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
• Spacer options 10, 15, 20, 30 and 50mm• Suitable for 10, 12, 15, and 19mm glass
Specify at time of order• Finish required• Diameter & Spacer options:
• BF600-38/10 • BF600-50/10• BF600-38/15 • BF600-50/15• BF600-38/20 • BF600-50/20• BF600-38/30 • BF600-50/30• BF600-38/50 • BF600-50/50
Product Diameter Spacer
38/50 38/50
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
BF630
50mm Diameter Covered Flange Plate
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• Finish required
Flange Tapered Range
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Available Sizes:
• 38mm Spacer – BF620-38• 50mm Spacer – BF620-50
Specify at time of order• Finish required• Size
BF620
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
38/50 38/50
5050
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C27
page
BF650
50mm Diameter Covered Range
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Available Sizes:
• 38mm Spacer – BF650-38• 50mm Spacer – BF650-50
Specify at time of order• Finish required• Size
50mm Diameter Nut
Technical Details
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Available Sizes:
• 38mm Spacer – BF640-38• 50mm Spacer – BF640-50
Specify at time of order• Finish required• Size
BF640
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
38/50 38/50
38/5038/50
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
BF660
Long Plate With M12 Threaded Rod Used For BF1600 & BF1700
Available Finishes
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• Finish required
Short Plate With M12 Threaded Rod Used For BF1600 & BF1700
Available Finishes
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• Finish required
BF670
75mm Offset M12 Wall Bracket
Available fi nish
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• Finish required
BF700
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C29
page
BF710
80mm Offset M12 Wall Bracket
Available fi nish
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• Finish required
Offset M12 Offset Post Bracket
Available fi nish
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• Finish required
BF720
Masonry Wall Bracket
Available fi nish
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• Finish required
BF730
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected]
page
BF740
150mm Straight Rod M12 Thread
Available fi nish
• 316 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• Finish required
150mm M12 Threaded Rod
Available fi nish
• 304 grade satin stainless steel fi nish(ex stock) other fi nishes can be made to order
Specify at time of order• BF750• BF750LS• Finish required
BF750 & BF750LS
BF800-060.6mm Black nylon washers
BF800-101.0mm Black nylon washers
BF800-161.6mm Black nylon washers
BF8201.6mm Black nylon washers
BF8301.6mm Black nylon washers
BF800, BF820, BF830 washers
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.
BF750LS
BF750
75-77 Ricketts Rd, Mt Waverley, VIC 3149Tel: (03) 8562 0888 Fax: (03) 8562 0899Toll Free: 1800 099 918 Email: [email protected] C31
page
GA Grips
Multi Grips With Plastic Jaws
Clear Protective Sleeve
Please Note: BF810-20 to suit BF650 head
BF810
© Copyright 2010 This document & its contents including images, drawings & specifi cation are the exclusive property of Fethers Glazing Systems Pty Ltd, & must not be copied or used directly or indirectly in any way. Unauthorised use may result in legal action.