Chopper/ ML Roller Attachment - Great Plains Ag569-400M 01/23/2018 2 Chopper/ ML Roller Attachment Great Plains Manufacturing, Inc. Be Familiar with Safety Decals Read and understand

Chopper/ ML RollerAttachment

Manufacturing, Inc.www.greatplainsmfg.com

Read the operator’s manual entirely. When you see this symbol, thesubsequent instructions and warnings are serious - follow withoutexception. Your life and the lives of others depend on it!

Illustrations may show optional equipment not supplied with standard unit.

© Copyright 2018 Printed 2018-01-23 569-400M

ENORIGINAL INSTRUCTIONS

ii Turbo Max Great Plains Manufacturing, Inc.

569-400M 2018-01-23

Great Plains Manufacturing, Inc. Important Safety Information 1

Important Safety Information

Look for Safety SymbolThe SAFETY ALERT SYMBOL indicates there is apotential hazard to personal safety involved and extrasafety precaution must be taken. When you see thissymbol, be alert and carefully read the message thatfollows it. In addition to design and configuration ofequipment, hazard control and accident prevention aredependent upon the awareness, concern, prudence andproper training of personnel involved in the operation,transport, maintenance and storage of equipment.

Be Aware of Signal WordsSignal words designate a degree or level of hazardseriousness.

DANGER indicates an imminently hazardous situationwhich, if not avoided, will result in death or serious injury.This signal word is limited to the most extreme situations,typically for machine components that, for functionalpurposes, cannot be guarded.

WARNING indicates a potentially hazardous situationwhich, if not avoided, could result in death or seriousinjury, and includes hazards that are exposed whenguards are removed. It may also be used to alert againstunsafe practices.

CAUTION indicates a potentially hazardous situationwhich, if not avoided, may result in minor or moderateinjury. It may also be used to alert against unsafepractices.

Use Adequate Lifting MeansThe frame sections and gangs of this machine are extremely heavy. If using multiple lifters, make sure each is rated for at least its share of the load.

Prepare for Emergencies Be prepared if a fire starts

Keep a first aid kit and fire extinguisher handy.

Keep emergency numbers for doctor, ambulance, hospitaland fire department near phone.

01/23/2018 569-400M

2 Chopper/ ML Roller Attachment Great Plains Manufacturing, Inc.

Be Familiar with Safety Decals Read and understand the “Safety Decals” section of the

Operators Manual.

Read all instructions noted on the decals.

Keep decals clean. Replace damaged, faded and illegibledecals.

Wear Protective Equipment Wear protective clothing and equipment.

Wear clothing and equipment appropriate for the job.Avoid loose-fitting clothing.

Because prolonged exposure to loud noise can causehearing impairment or hearing loss, wear suitablehearing protection such as earmuffs or earplugs.

Because operating equipment safely requires your fullattention, avoid wearing entertainment headphones whileoperating machinery.

Avoid High Pressure FluidsEscaping fluid under pressure can penetrate the skin,causing serious injury.

Avoid the hazard by relieving pressure beforedisconnecting hydraulic lines.

Use a piece of paper or cardboard, NOT BODY PARTS, tocheck for suspected leaks.

Wear protective gloves and safety glasses or goggles whenworking with hydraulic systems.

If an accident occurs, seek immediate medical assistancefrom a physician familiar with this type of injury.

Use Safety Lights and DevicesSlow-moving tractors and towed implements can createa hazard when driven on public roads. They are difficultto see, especially at night.

Use flashing warning lights and turn signals wheneverdriving on public roads.

Use lights and devices provided with implement.

Keep Riders Off MachineryRiders obstruct the operator’s view. Riders could bestruck by foreign objects or thrown from the machine.

Never allow children to operate equipment.

Keep all bystanders away from machine during operation.

Shutdown and Storage Lower implement, put tractor in park, turn off engine, and

remove the key.

Secure Chopper/ML Roller Attachment using blocks andsupports provided.

Detach and store Chopper/ML Roller Attachment in an

569-400M 01/23/2018


area where children normally do not play.

Tire SafetyTire changing can be dangerous and should beperformed by trained personnel using correct tools andequipment.

When inflating tires, use a clip-on chuck and extensionhose long enough for you to stand to one side–not in frontof or over tire assembly. Use a safety cage if available.

When removing and installing wheels, use wheel-handlingequipment adequate for weight involved.

Safety At All TimesThoroughly read and understand the instructions in thismanual before operation. Read all instructions noted onthe safety decals.

Be familiar with all machine functions.

Operate machinery from the driver’s seat only.

Do not leave machine unattended with tractor enginerunning.

Do not stand between the tractor and machine duringhitching.

Keep hands, feet and clothing away from power-drivenparts.

Wear snug-fitting clothing to avoid entanglement withmoving parts.

Watch out for wires, trees, etc., when folding and raisingmachine. Make sure all persons are clear of working area.

01/23/2018 569-400M


IntroductionThe Chopper/ML Roller Attachment has been designedwith care and built by skilled workers using qualitymaterials. Proper setup, maintenance, and safeoperating practices will help the customer get years ofsatisfactory use from the machine.

Description of UnitThis is for the Chopper/ML Roller attachment only. Thisattachment is used to further smooth, break clods, tieresidue to the soil and firm.

Tools Required• Basic Hand Tools

• Torque Wrench

• Fork Truck, Overhead Hoist or Loader

Pre-assembly Checklist Before assembling, read and understand “Important

Safety Information” in front part of this manual.

Have at least two people on hand while assembling.

Make sure area is level and free of obstructions (preferably an open concrete area).

Have all major components

Have all fasteners and pins shipped with machine.

Unpacking Boxes Position boxes in area that you can maneuver

components up to machine to assembly.

1. Carefully remove banding from boxes.

2. Carefully remove banding from chopper assemblies and roller gangs.

3. Locate and identify all components before assembling.

Further AssistanceGreat Plains Manufacturing, Inc. wants you to be

satisfied with your new Turbo Chisel Narrow. If for any reason you do not understand any part of this manual or

are otherwise dissatisfies with the product please contact:

Great Plains Service Department1525 E. North St.

PO Box 5060Salina, KS 67402-5060

Or go to www.greatplainsag.com and follow the contactinformation at the bottom of your screen for our servicedepartment.

Figure 1Chopper/ML Roller Attachment

TP-69189

569-400M 01/23/2018


Updating Parts

3

4

1

6

11

5

4

11

Figure 2Torque Tube

43724 43732a

01/23/2018 569-400M


Chopper/ML Roller Conversion KitRefer to Figure 2 & Refer to Figure 3

When installing new Chopper/ML Roller attachment on a machine with S/N GP-D1146-, several parts need to bereplaced with new, including the torque tube, lift plates and walking beams.

The original hardware will be used to reinstall the new parts, so be sure not to discard or damage it.

The existing torque tube #566-233H must be replaced with torque tube #566-313H. The lift plates 566-432D (#4 onparts drawing) must also be replaced with new plates 566-444D. The left hand walking beam #566-225H will needreplaced with #566-314H, and the right hand walking beam 566-226H will need replaced with #566-315H. Removethe hubs #815-302C these will be used on the new torque tubes.

4. To replace the torque tube lift the unit slightly off the ground and use block or stands to support the weight of themachine.

5. Remove the tires and walking beams from the original torque tube.

6. Unhook the hydraulic lift cylinders from the torque tube and the lift plates . Do not unhook the hydrauliclines, but place the cylinders out of the way to keep them from being damaged.

7. Unhook the center lift straps from the torque tube but you may leave them attached to the leveling h-bracket.Also unhook the depth stop tube.

8. Removing the shanks from the mounts will make this process easier, but leaving just the mounts in place isrecommended.

9. Remove the torque tube and slide it out from underneath the machine. Slide the new torque tube in place anduse the 1.25 x 7.59 pins to secure it to the frame. Re-attach the center lift straps and the depth stop tube.

10. Install the new walking beams on the torque tube , reuse the center pivot spindle , spindle sleeve ,washers, which must be installed on the outside of the walking beam, slotted nut and cotter pin. Do not put thetires back on yet.

11. Replace the lift plates with the new ones using the original hardware. Attaching lift plate to the frame and thelift strap . Then you may reinstall the hydraulic cylinder , attaching it to the lift plate and the torque tube .The tires can now be put back on, and the blocks or stands can be removed.

1

2

3 1 4

5 1

1 16 5

2 1 7 89

10

4 4

11 3 4 1

Figure 3Walking Beams

43674

2

7

8

9

10

569-400M 01/23/2018


Refer to 4

12. There are flat plates that need to be installed inthe tongue . Remove the clevis hitch and thesmall plate that is behind it by removing thebolts . Slide all 8 of the flat plates into thetongue and reinstall the small plate , bolts ,and the clevis hitch . This adds needed weight tothe front of the machine.

Figure 4Flat Plates

43671

3

1

4

25

12 34

5 12 4 5

3

01/23/2018 569-400M


ex

Chopper/ML Roller Conversion KitFigure 5

The existing attachment will need to be removed before starting to install the new Chopper/ML Roller attachment.Be sure to save the chopper assemblies, See “Chopper/ML Roller Chopper Assembly” on page 12, thesechoppers will be re-used on the new attachment assemblies.

13. Locate the rear frame ext , for both the wings and the center frame. Attach to rear of machine using34 x 6132 x 558 U-Bolt , 34 lock washers and hex nuts. See Machine Layouts page 24 thru page 27 forplacement of rear frame extensions.

14. Chopper arm mounts , will be shipped attached and in the correct locations on the rear frame ext. The chopperarms , will need installed into the arm mounts using 1 x 4 pin , and secure pin with 38 x 2 hex bolt, and 38 toplock. See “Chopper/ML Roller Chopper Mounts Attachment” on page 10 for parts break down and layouts onpage 24 thru page 27 for placement on the specific model of machine.

15. Locate the chopper assemblies , that you removed from the old attachment, See page 12 for part break down,and using chopper mounting clamps , 58 x 3132 x 512 u-bolts , 58 lock washers and hex nuts, install the c-flex

chopper hangers , into the mounting clamps and secure the clamps, using the 58 x 3132 x 512 u-bolts 58 lockwashers and nuts to the chopper arms.

16. The spring eye bolts , will need to be installed into the chopper arm mounts and chopper arms using 1.0 x4.06 clevis pin and secured with 14 x 134 linch pin. See “Chopper/ML Roller Chopper Mounts Attachment”on page 10 for part break down.

17. The roller arms will come attached to the roller arm mount brackets , the cylinders will be attached and the 2short hoses will be installed in place and attached to the bulkhead fittings on the roller arm mount bracket . Themounts will need attached to the rear ext frame in the proper locations using 34 x 4132 x 538 u-bolt, 34 lock

washer and hex nuts to secure the roller arm mounts to the rear ext frame . See machine layouts on page 24thru page 27, for roller arm mount placement.

18. The roller gangs will need attached to the arms , using 5 8 x 31 32 x 41 4 u-bolts , 5 8 lock washers and hnuts. See “Chopper/ML Roller Gang Attachment Arms” on page 14 and “Chopper/ML Roller GangAssembly” on page 16, for parts breakdown. The same u-bolts are used to attach the rollers to the rollertubes. See machine layouts page 24 thru page 27, for roller gang placement on your model of machine.

19. Hydraulics will need to be run from the tractor, along the machine and to the rear middle bulkhead bracketbulkhead fittings. See “Chopper/ML Roller Hydraulic Assembly” on page 18 for parts break down, placement offittings and hoses. See hydraulic layouts page 22 and page 23, for hose route from the hitch to the rear of themachine, the hoses may need attached to the center bulkhead fittings.

1

2

3

4 5

6

7 8

16 8

9 3 4

10

11 12

12

13

12 1

14 11 15

15

569-400M 01/23/2018


1

5

10 23

6

7

8

9

4

11 12

14

15

13

12

16

Figure 5Chopper/ML Roller Attachment

TP-69133

01/23/2018 569-400M


Chopper/ML Roller Chopper Mounts Attachment

TP-69131

569-400M 01/23/2018


dwgTP-69131 Image No.

1 569-361H THREE CHOPPER ARM RH

1 569-359H THREE CHOPPER ARM LH

2 569-347H INDIVIDUAL CHOPPER ARM

3 569-346H CHOPPER ARM MOUNT

4 569-348H CHOP DEPTH ADJUST BRACKET

5 569-360H SINGLE CHOP ARM MOUNT

6 569-349H SPRING EYE BOLT

7 807-369C SPRING COMP 1.88ODX12.56X.38W

8 802-487C HHCS 3/4-10X6 GR8

9 804-023C WASHER LOCK SPRING 3/4 PLT

10 803-027C NUT HEX 3/4-10 PLT

11 805-412C PIN CLVS 1.0X4.06 USBL

12 805-126C PIN LINCH 1/4 X 1 3/4 PLT

13 805-590C PIN - 1 X 4 HRD PLT

14 802-143C HHCS 3/8-16X2 GR5

15 803-123C NUT HEX TOP LOCK 3/8-16 PLT

16 858-928C DECAL - HOLE LOCATION

01/23/2018 569-400M


Chopper/ML Roller Chopper Assembly

TP-69129

569-400M 01/23/2018



1 891-219C EC STYLE END CAP

2 569-092D SPINDLE


4 803-021C NUT HEX 5/8-11 PLT

5 569-321H CHOPPER MOUNTING CLAMP

6 806-079C U-BOLT 5/8-11 X 3 1/32 X 5 1/2

7 807-340C C-FLEX CHOPPER HANGER 1 X 2

8 802-065C HHCS 3/4-10X2 1/4 GR5


10 569-153D CHOPPER CASTING DBL MNT - MACH

11 803-149C NUT HEX 7/8-14 PLT


13 569-204K CHOPPER HUB ASSEMBLY Includes items 24-26, 1 & 2

14 569-206H CHOPPER WHEEL WELDMENT

15 170724 PLOW BOLT, 7/16” x 1 1/2” #3

16 820-442C CHOPPER BLADE 3/8 X 4 1/2 X 5

17 804-014C WASHER LOCK 7/16 PLT

18 803-015C NUT HEX 7/16-14 PLT

19 569-231S CHOPPER WHEEL SUB ASSEMBLY Includes items 14-18


21 802-091C HHCS 1/2-13X1 1/2 GR5

22 569-325H CHOPPER MNT - SNGL RH Models MC5111 & MC5315

22 569-326H CHOPPER MNT - SNGL LH Models MC5111 & MC5315

23 569-327L CHOPPER ASSEMBLY - SNGL RH Includes items 11-13, & 22 Models MC5111 & MC5315

23 569-328L CHOPPER ASSEMBLY - SNGL LH Includes items 11-13, & 22 Models MC5111 & MC5315

24 569-091D REAR SLEEVE

25 816-679C 2.5 OD DUAL LIP GREASE SEAL

26 569-230S CHOPPER HUB SUB ASSEMBLY

01/23/2018 569-400M


Chopper/ML Roller Gang Attachment Arms

TP-69130

569-400M 01/23/2018



1 569-345H REAR FRAME EXT - 5109 Models 5109

1 569-355H REAR FRAME EXT-CENTER 5111 Models 5111

1 569-356H REAR FRAME EXT-OUT 5111 Models 5111

1 569-357H REAR FRAME EXT-WING 5313 Models 5313

1 569-358H REAR FRAME EXT-CNTR 5300 Models 5313 & 5315

1 569-362H REAR FRAME EXT-WING 5315 Models 5315

2 569-350H ROLLER ARM MOUNT BRACKET

3 569-351H ROLLER ARM

4 810-555C CYL 1.5X2.5X.75 ROD W/CLEVIS Includes pins

5 842-424C HHCS 1-8X5 GR5 SPTHD

6 803-168C NUT HEX TOP LOCK 1-8 PLT

7 569-379L ROLLER ARM ASSEMBLY Includes Items 2-6

7 569-380L ROLER ARM ASSEMBLY - ENDS Includes Items 2-6

8 806-012C U-BOLT 3/4-10X4 1/32X5 3/8


10 803-027C NUT HEX 3/4-10 PLT

11 806-128C U-BOLT 3/4-10 X 6 1/32 X 5 5/8

12 806-018C U-BOLT 5/8-11 X 3 1/32X4 1/4G5


14 803-021C NUT HEX 5/8-11 PLT

15 838-615C DECAL REFLECTOR AMBER 2X9 Used on center drag frame only

01/23/2018 569-400M


Chopper/ML Roller Gang Assembly

TP-69128

569-400M 01/23/2018



1 569-188D TUBE - 3 X 3 Models MC5109 & 5313

1 569-204D TUBE - 3 X 3 Models MC5111 & 5315

1 569-208D TUBE - 3 X 3 Models MC5315

2 569-189D TUBE - 2 X 2 Models MC5109 & 5313

2 569-205D TUBE - 2 X 2 Models MC5111 & 5315

2 569-209D TUBE - 2 X 2 Models MC5315

3 569-190D PLATE - TORCHED

4 569-191D GANG BOLT - 10 WHL 6" ROLLER MC5109, MC5313

4 569-210D GANG BOLT - 11 WHL 6" ROLLER MC5315

4 569-207D GANG BOLT - 12 WHL 6" ROLLER MC5111, MC5315

5 569-192D TUBE RND - 2 OD

6 569-193D TUBE RND - 2 OD

7 569-206D PLATE - TORCHED

8 569-352H ROLLER BRNG HANG -RH GUSSET

9 569-353H ROLLER BRNG HANG -RH GUSSET

10 812-540C ROLLER-16ODX2.63LIPX2.38HUB

11 802-197C HHCS 5/16-18X2 3/4 GR5

12 804-075C WASHER FLAT 1/4USS PLT

13 803-301C NUT HEX SLOTTED 1 1/2-6 PLT

14 803-084C NUT HEX NYLOCK 5/16-18 PLT

15 804-066C WASHER MACH 2.25 X 1.50 X 14GA

16 802-041C HHCS 1/2-13X3 1/2 GR5

17 802-214C RHSNB 1/2-13X1 1/4 GR5

18 822-293C BEARING FLG 1 1/2ID 5 IN SQ

19 806-018C U-BOLT 5/8-11 X 3 1/32X4 1/4G5

20 806-005C U-BOLT 1/2-13 X 2 X 3 GR 5


22 803-020C NUT HEX 1/2-13 PLT


24 803-021C NUT HEX 5/8-11 PLT

25 569-354K ML ROLLER GANG - 10 WHL Includes items 1-24 Models MC5109 & 5313

25 569-364K ML ROLLER GANG - 11 WHL Includes items 1-24 Models 5315

25 569-363K ML ROLLER GANG - 12 WHL Includes items 1-24 Models MC5111 & 5315

01/23/2018 569-400M


Chopper/ML Roller Hydraulic Assembly

TP-69-132

569-400M 01/23/2018



1 811-394C CP 3/4FORB MALE QD POPPET TYPE

2 811-919C AD 3/4MORB 3/4FORB (HG)

3 841-542C HG HANDLE - BLUE EXT

4 841-543C HG HANDLE - BLUE RET

5 548-006S HG PAIR - BLUE MORB-FORB Includes items 2-4

6 811-063C EL 3/4MJIC 3/4MORB

7 569-213D PLATE - TORCHED Attached to Hitch

8 811-725C EL 90 3/4MJIC

9 810-300C PRESSURE GAUGE 3000 PSI

10 811-677C AS 9/16MORB 1/4FNPT

11 810-900C FIXED BYP DP VALVE W/O SOL

12 802-131C HHCS 5/16-18X3 GR5

13 804-009C WASHER LOCK SPRING 5/16

14 803-008C NUT HEX 5/16-18 PLT

15 550-346D HOSE WRAP, LARGE SIZE, LONG(15")

16 802-159C HHCS 5/16-18X1 GR5

17 589-248D HYD HOSE HOLDER TOP PLATE

18 816-885C HYDRAULIC HOSE HOLDER 3/8”

19 811-073C TE 3/4MJIC 3/4MJIC 3/4FJIC

20 811-039C TE 3/4MJICBH 3/4MJIC 3/4MJIC

21 811-216C EL 3/4MJIC 9/16MORB

22 841-993C EL 3/4MJIC BLKHD W/ LN

23 861-076C HH3/8R2 066 3/4FJIC 3/4MORB Models 5109 - 5315

24 811-889C HH3/8R2 300 3/4FJIC Models 5109 - 5315

25 811-128C HH3/8R2 025 3/4FJIC Models 5109

25 811-939C HH3/8R2 039 3/4FJIC Models 5111

25 811-841C HH3/8R2 024 3/4FJIC Models 5313

25 861-157C HH3/8R2 040 3/4FJIC Models 5315

26 811-929C HH3/8R2 030 3/4FJIC Models 5109

26 811-943C HH3/8R2 033 3/4FJIC Models 5111

26 851-040 HH3/8R2 034 3/4FJIC Models 5313 & 5315

27 811-929C HH3/8R2 030 3/4FJIC Models 5109 - 5315 On Models 5313 & 5315 this will be the 3 center hose pairs

28 841-004C HH3/8R2 011 3/4FJIC Models 5109 - 5315

29 841-008C HH3/8R2 017 3/4FJIC Models 5109 - 5315

30 802-013C AD 3/4MORB 3/4FJIC

31 811-324C AD 3/4MORB 3/4FJIC

01/23/2018 569-400M


Appendix - Reference Information

Torque Values Chart

Torque Values Chart

Wheel Bolt Torque Values 12”-20 (75-85ft-lbs)



Chopper Hub Spindle Values 78”-9 (350 ft-lbs)

94 6

25199m

BoltSize

Bolt Head IdentificationBoltSize

Bolt Head Identification

Grade 2 Grade 5 Grade 8 Class 5.8 Class 8.8 Class 10.9in-tpia N-mb N-m N-m mm x pitchc N-m N-m N-m1⁄4-20 7.4 11 16 M 5 X 0.81⁄4-28 8.5 13 18 M 6 X 1 7 11 155⁄16-18 15 24 33 M 8 X 1.25 17 26 365⁄16-24 17 26 37 M 8 X 1 18 28 393⁄8-16 27 42 59 M10 X 1.5 33 52 723⁄8-24 31 47 67 M10 X 0.75 39 61 857⁄16-14 43 67 95 M12 X 1.75 58 91 1257⁄16-20 49 75 105 M12 X 1.5 60 95 1301⁄2-13 66 105 145 M12 X 1 90 105 1451⁄2-20 75 115 165 M14 X 2 92 145 2009⁄16-12 95 150 210 M14 X 1.5 99 155 2159⁄16-18 105 165 235 M16 X 2 145 225 3155⁄8-11 130 205 285 M16 X 1.5 155 240 3355⁄8-18 150 230 325 M18 X 2.5 195 310 4053⁄4-10 235 360 510 M18 X 1.5 220 350 4853⁄4-16 260 405 570 M20 X 2.5 280 440 6107⁄8-9 225 585 820 M20 X 1.5 310 650 900

7⁄8-14 250 640 905 M24 X 3 480 760 1050

1-8 340 875 1230 M24 X 2 525 830 1150

1-12 370 955 1350 M30 X 3.5 960 1510 2100

11⁄8-7 480 1080 1750 M30 X 2 1060 1680 2320

11⁄8-12 540 1210 1960 M36 X 3.5 1730 2650 3660

11⁄4-7 680 1520 2460 M36 X 2 1880 2960 4100

11⁄4-12 750 1680 2730

13⁄8-6 890 1990 3230 a. in-tpi = nominal thread diameter in inches-threads per inch

13⁄8-12 1010 2270 3680 b. N· m = newton-meters

11⁄2-6 1180 2640 4290

11⁄2-12 1330 2970 4820

c. mm x pitch = nominal thread diameter in mm x thread pitch

Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.

5.8 8.8 10.9

25199

ft-lbd ft-lb ft-lb ft-lb ft-lb ft-lb5.6 8 12

6 10 14 5 8 11

11 17 25 12 19 27

13 19 27 13 21 29

20 31 44 24 39 53

22 35 49 29 45 62

32 49 70 42 67 93

36 55 78 44 70 97

49 76 105 66 77 105

55 85 120 68 105 150

70 110 155 73 115 160

79 120 170 105 165 230

97 150 210 115 180 245

110 170 240 145 230 300

170 265 375 165 260 355

190 295 420 205 325 450

165 430 605 230 480 665

185 475 670 355 560 780

250 645 910 390 610 845

275 705 995 705 1120 1550

355 795 1290 785 1240 1710

395 890 1440 1270 1950 2700

500 1120 1820 1380 2190 3220

555 1240 2010

655 1470 2380

745 1670 2710

870 1950 3160d. ft-lb = foot pounds

980 2190 3560

3 5 7

569-400M 01/23/2018

Great Plains Manufacturing, Inc. Appendix - Reference Information 21

Tire Inflation Chart

Hydraulic Connectors and TorqueRefer to Figure 6 (a hypothetical fitting)Leave any protective caps in place until immediately priorto making a connection.

Tire Inflation Chart Tire Warranty Information

Wheel Tire Size InflationAll tires are warranted by the original manufacturer of the tire. Tire warranty information is found in the brochures included with your Operator’s and Parts Manuals or online at the manufacturer’s web sites listed below. For assistance or information, contact your nearest Authorized Farm Tire Retailer.Manufacturer Web siteFirestone www.firestoneag.comGleason www.gleasonwheel.comTitan www.titan-intl.comGalaxy www.atgtire.comBKT www.bkt-tire.com

Transport 12.5L x 15 12-Ply52 psi

(358 kPa)

Transport 340/60R16.5 73 psi

(503 kPa)

NPT - National Pipe ThreadNote tapered threads, no cone/flare, and no O-ring.Apply liquid pipe sealant for hydraulic applications.Do not use tape sealant, which can clog a filter and/or plug an orifice.

JIC - Joint Industry Conference (SAE J514)Note straight threads and the 37 cone on “M” fittings (or 37 flare on “F” fittings).Use no sealants (tape or liquid) on JIC fittings.

ORB - O-Ring Boss (SAE J514)Note straight threads and elastomer O-Ring .Prior to installation, to prevent abrasion during tightening, lubricate O-Ring with clean hydraulic fluid.Use no sealants (tape or liquid) on ORB fittings.ORB fittings that need orientation, such as the ell depicted, also have a washer and jam nut (“adjustable thread port stud”). Back jam nut away from washer. Thread fitting into receptacle until O-Ring contacts seat. Unscrew fitting to desired orientation. Tighten jam nut to torque specification.

2

5

4

98

75

3

Figure 6Hydraulic Connector ID

31282

Fittings Torque ValuesDash Size Fitting N-m Ft-Lbs

-4 14-18 NPT 1.5-3.0 turns past finger tight

-5 12-20 JIC 19-20 14-15

-5 12-20 ORB w/jam nut 12-16 9-12

-5 12 -20 ORB straight 19-26 14-19

-6 516-18 JIC 24-27 18-20

-6 516-18 ORB w/jam nut 16-22 12-16

-6 516-18 ORB straight 24-33 18-24

-8 34 -16 JIC 37-53 27-39

-8 34 -16 ORB w/jam nut 27-41 20-30

-8 34-16 ORB straight 37-58 27-43

1

1

24 5

3

5 7

8 9

01/23/2018 569-400M

http://www.firestoneag.com

http://www.gleasonwheel.com

http://www.titan-intl.com

http://www.firestoneag.com

http://www.gleasonwheel.com


MC5109 & MC5111 Chopper/ML Roller Hydraulic Layout

TP-69138

569-400M 01/23/2018


MC5313 & MC5315 Chopper/ML Roller Hydraulic Layout

TP-69139

01/23/2018 569-400M


MC5109 Chopper/ML Roller Layout

TP-69134

569-400M 01/23/2018



TP-69135

01/23/2018 569-400M



TP-69136

569-400M 01/23/2018



TP-69137

01/23/2018 569-400M


569-400M 01/23/2018

Great Plains, Mfg.1525 E. North St.P.O. Box 5060Salina, KS 67402

Documents

Chopper/ ML Roller Attachment - Great Plains Ag569-400M 01/23/2018 2 Chopper/ ML Roller Attachment Great Plains Manufacturing, Inc. Be Familiar with Safety Decals Read and understand