8/14/2019 Claims to CTM 7.11

1/7

1. AUM-We have problems when producing Reflectors(the smallest size of plate)

the material is bending too much when its going through the white plastic

reel(the reel used as a sensor for automatic uncoiling of the plate). Probably

its too heavy, and its also trying to pull the material to the side. Than the

plate is not going perfectly into the straightening reel.

We will design another arm that will take care of this problem.

Velux: Arm has to be lighter and not so wide

2. ATMM-We have a lot of hydraulic oil leakages under the hydraulic cylinders

on the punch station(the big one) and on the shear station.

Is it possible to have more specific indicators

on the leaks? The leak could be from several sources; hoses, fittings,

distribution block or cylinders. It would be a real help if we would know as exact

as possible from where the oil is coming. Solvent and wiping dry the entire area

will provide an opportunity to observe the start of the leak(s). A photograph of

the start of the leak would be helpful.

Velux:

Leakeages are from 3 cylinders and fittings as well! Leaks comes directly under

cylinders.

8/14/2019 Claims to CTM 7.11

2/7

3. ATMM-Sometimes the plate is bending too much inside of the machine when

its stopping the movement (all the way between the straightening reels and

the shifting reel)

Youll need to support the material over the

length (not diagonal as you show in the picture). Well provide two parts made of

plastic plates to solve this problem.

Velux: ensure such a support on every black reel.

4. ATMM-when we put the shifting reel all the way down to the plate(we loose

the lifting screws completely) than its pulling the plate to the side. Its

pushing the plate towards the small leading wheel on the side and its

making the plate curly on this side.

This is the result of not having correct

alignment of the material being supplied to the machine. It is possible that the

un-coiler (AUM) is not positioned correctly to provide the material in alignment

with intended path through the machine (ATMM).

Velux: uncoiler is aligned almost perfectly (+- 2 mm difference in diagonals).

When you were here it was set up +- 2 cm.

8/14/2019 Claims to CTM 7.11

3/7

5. ATMM-We are not able to produce the Elbow without changing the original

adjustments of machine. I mean we needed to move the whole material 2mm

towards to control panel to get the right dimensions.

This problem has the same solution as the

previous problem.

Velux: Dont agree, see point above.

6. ATMM- sometimes when the plate goes out of the shear unit ,it hits the

orange colour rollers on the next station. The idea to flatten the plate with

the straightening reels doesnt work all the time.

This picture shows that you are running Top and Bottom elbow material without

the Keyway Guard Bottom Shear Blade part number 40888, in place (refer to

figure next to the photo). This part was provided with the machine and is

intended to be used whenever you do not use the profile knife for the shear. It

will be very difficult for the material to go easily on the conveyor rollers, without

this part. And you are correct, whether the material is straightened or not will

not affect this problem very much.

Velux: We lost Keyway Guard Bottom Shear Blade. Could you send a drawing,

and we will ensure a new one.

8/14/2019 Claims to CTM 7.11

4/7

7. ATMM-When we have to add the additional shear to the shear unit

(production of telescopic tubes) after cutting, the plate holds on the shear

and it doesnt continue. (Its like sticked on the shear)

The material is sticking here on the shear.

We will provide two guides that will increase the friction between the material

and the rollers. The material will then be pulled from the shear blade.

Additionally, the guides will dampen the material from bouncing at the entranceof the conveyor.

Velux: ok, please provide it.

8. AAM- A lot of fittings on the hydraulic hoses are not tighten enough and than

we have the leakages of the oil.

Please determine the color of the oil that is leaking. If it is red in appearance

then it is a hydraulic system leak. In this case tightening the hoses will likely

solve the oil leaks. If the oil is not red, it is spent lubricant used in forming

the elbow. Used lubricant oil can be captured with small pan under the

machine.

Velux:

9. AAM- sometimes when the operator removes the finished part, the machine

tries to start again without operators command.

8/14/2019 Claims to CTM 7.11

5/7

This is a very serious issue. We need more information regarding how and when

this occurs. Can you provide more details on this situation? We need to know if

the problem is repeatable or occurs at random. Please record the exact

conditions when this occurs. For example, the machine is in automatic mode or

setup mode, or after an emergency stop, or right after setup mode and switched

to automatic mode. You mentioned that the machine tries to start, what

movements do you see on the machine?

Velux: Happened only sometimes. It happends when operator is using foot

switch (pedal) for fixing elbow, when he wants to turn it after fininshing. Machine

is in automatic mode and machine tries to start again, but it switch off

automaticaly because of lights curtains. It happends not after pressing

emergency button or whatever else. Just it happends, during removing final

elbow.

10.ATMM- we have problems with this small spindle that is missing a cotter pin

and it has a tendency to jump out.

The defective part will be replaced.

8/14/2019 Claims to CTM 7.11

6/7

11.ATMM- In last week we had a problem with broken punch pin on the small

punch station. It happened two times. We found the reason for this problem-a

tiny film of aluminum was sticked on the punch pin and also inside of the hole

for punching. When there was too much of aluminum, the punch pin was

blocked inside of the hole and didnt come up. Than the machine moved the

plate and broke it.

A good solution to prevent this damages would be to add some kind of

sensors on the hydraulic cylinders(on both of them).Those sensors will

always detect the position of the piston. If it will stick inside like it happened

here, it will not allow the machine to continue.

And for that problem with the tiny film of aluminum we will try to spray the

punches with oil more often. But still we need any suggestions how to avoid

these damages with the sticky aluminum.

Sticked together after

8/14/2019 Claims to CTM 7.11

7/7

This issue is still in discussion. We will provide a solution soon.