Configuration_OMSN_R4_4-5_2_Ed01

Alcatel University - 3FL 40034 AEAA WBZZA Ed.013.1

3 Equipment Configuration

3.2

3 Equipment ConfigurationSession presentation

Objective: to be able to configure a network element Program:

3.1 OMSN Configuration3.2 Board Substitution/Database Clearing3.3 Specific Configuration3.4 ISA board Configuration



3.1 OMSN Configuration

3.4

3.1 OMSN ConfigurationBoards Alarms

Replaceable unit missing. This alarm indicates that there is configured a board in the software that doesnt exist in the hardware .

Replaceable unit type mismatch. This alarm indicates that there is configured a board in the software but it isn't the right one.

Unconfigured equipment present. This alarm indicates that the board is plugged in the equipment but the board isnt configured in the software.

Replaceable unit problem.The board could be broken.

3.5

3.1 OMSN ConfigurationSetting Procedure

Is

the slot

empty?

Select an alarmed slot in the subrack view

SET the board OUT OF SERVICE

REMOVE the board

SET the board

Yes

No

Isthere the padlock?

Procedure that has to be executed for every board/module that has one of the alarm seen

before

END

Find the correct board with the REMOTE INVENTORY

No

Yes

3.6

3.1 OMSN Configuration Exercise

9 Set one equipment.

Time allowed : 25 minutes



3.2 Board Substitution/Database Clearing

3.8

3.2 Board Substitution/Database Clearing Procedure for clearing the database

To start with the BASIC CONFIGURATION it is necessary to clear the Database of the Equipment Controller(EC) following this procedure

I- Extract the EC card.II- Move the micro-switch inside the card as indicated in figure 2 below.III- Insert the EC card and wait until the leds on the front of the board turn on.IV- Verify that the database is cleared: all the slots appear empty, except for the

following main cards: EC card , MATRIX, CONGI and Bus Termination.V- Extract the EC card, set the micro-switch in the original position: a warning alarm

appears in the slots where a card is inserted.

EQUICO, SYNTH1N

ON

OFF

1 2 3 4ON

OFF

1 2

PQ2/EQC, SYNTH4

ON

OFF

1 2 3 4ON

OFF

1 2 Normal operating condition

figure 1

Move the switch#2 from OFF to ON to clean the database

figure 2

3.9

3.2 Board Substitution/Database ClearingSubstitution of the EC card

New unit hw condition.Unit with wrong or

unknown sw?New unit hw condition.

Unit without sw?New unit hw condition.Unit with different sw?

New unit hw condition.Sw of the same release and NE?

Hw-preset the new unit with: switch#1=OFF, switch#2=ON (reset database)Insert the new unit

Remove and hw-preset the new unit with: switch#1=ON, switch#2=ON.

Insert the new unit again

Download the NE relevant sw release with normal

download procedure

Download the NE relevant sw release with

SIBDL procedure

Remove and hw-preset the new unit with: switch#1=ON, switch#2=OFF(reset database and upload comm/routing tables)

Insert the new unit again

Is the MIB stored in the Craft Terminal?

From CT send the saved MIB containing the correct configuration

From OS send the saved MIB containing the correct configuration

From CT activate the sent MIBFrom OS activate the sent MIB

Remove and hw-preset the new unit with: switch#1=OFF, switch#2=OFF(normal operating condition)Insert the new unit again

YESNO

3.10

3.2 Board Substitution/Database ClearingSubstitution of ATM card

I1-4: switch#4

3.11

3.2 Board Substitution/Database Clearing Exercise

9 Change the EQUICO or SYNTH board. Remember to save the configuration data with Mib Management function in Download menu before clearing the database.

Time allowed : 30 minutes



3.3 Specific Configuration

3.13

3.3 Specific ConfigurationAuto Laser Shutdown

Select SPIPort Physical MediaALS ManagementSelect SPIPort Physical MediaALS Management

3.14

3.3 Specific ConfigurationTP Configuration: RST

In Port View select RST Port TP Configuration

3.15

3.3 Specific ConfigurationTP Configuration: VC4 and VC3

In Port View select VC4 or VC3 Port TP Configuration

3.16

3.3 Specific ConfigurationTP Configuration: VC12

In Port View select VC12 Port TP Configuration

3.17

3.3 Specific ConfigurationTP Threshold Configuration

(i.e.) In Port View select MST Port TP Thresholds Configuration

Poisson Distribution

BurstyDistribution

3.18

3.3 Specific ConfigurationRetiming Function

3.19

3.3 Specific ConfigurationIntroduction on E1 and P12

PDH Signal with AIS

111

111 RX

100

011

POH

VC12

PAYLOAD with errored

bits

RX

TX

TX

100

011

UPSTREAM UPSTREAM

DOWNSTREAMDOWNSTREAM

: Errored bits

PAYLOAD with errored

bits

3.20

3.3 Specific ConfigurationTP Frame Mode Configuration

In Port View select P12 Port TP Frame Mode Configuration

3.21

3.3 Specific ConfigurationChange 140Mbit/s interface into 155Mbit/s interface

PDH 140Mbit/s interface

SDH 155Mbit/s Electrical interface

3.22

3.3 Specific ConfigurationPort Mode



3.4 ISA board Configuration

3.24

3.4 ISA board ConfigurationPort Configuration

Time Slot Switch

STM1 Number

STM1 Time Slot

For creating a new port

SignalConcatenation Level

For assigning a newSTM1 Time Slotand/or a new STM1 Number to the selected VC

3.25

3.4 ISA board Configuration Control Path Activation

3.26

3.4 ISA board Configuration LCAS Configuration

3.27

3.4 ISA board Configuration LCAS Monitoring

3.28

3.4 ISA board Configuration Ethernet Port Configuration

3.29

3.4 ISA board Configuration Ethernet Mapping Protocol configuration

E

T

H

-

M

B

GETH-MB

PR-EA ES1-8FE

ISA-ES16ES4-8FE

ES1-8FX

3.30

3 Equipment ConfigurationEvaluation

Objective: to be able to configure a network element

Thank you for answeringthe self-assessment

of the objectives sheet

3 Equipment Configuration3 Equipment ConfigurationSession presentation3 Equipment Configuration3.1 OMSN ConfigurationBoards Alarms3.1 OMSN ConfigurationSetting Procedure3.1 OMSN Configuration Exercise3 Equipment Configuration3.2 Board Substitution/Database Clearing Procedure for clearing the database3.2 Board Substitution/Database Clearing Substitution of the EC card3.2 Board Substitution/Database ClearingSubstitution of ATM card3.2 Board Substitution/Database Clearing Exercise3 Equipment Configuration3.3 Specific Configuration Auto Laser Shutdown3.3 Specific Configuration TP Configuration: RST3.3 Specific ConfigurationTP Configuration: VC4 and VC33.3 Specific Configuration TP Configuration: VC123.3 Specific ConfigurationTP Threshold Configuration3.3 Specific Configuration Retiming Function3.3 Specific Configuration Introduction on E1 and P123.3 Specific Configuration TP Frame Mode Configuration3.3 Specific ConfigurationChange 140Mbit/s interface into 155Mbit/s interface3.3 Specific ConfigurationPort Mode3 Equipment Configuration3.4 ISA board ConfigurationPort Configuration3.4 ISA board Configuration Control Path Activation3.4 ISA board Configuration LCAS Configuration3.4 ISA board Configuration LCAS Monitoring3.4 ISA board Configuration Ethernet Port Configuration3.4 ISA board Configuration Ethernet Mapping Protocol configuration3 Equipment ConfigurationEvaluation

Documents

Configuration_OMSN_R4_4-5_2_Ed01