Corroseal rust converter is an elite, industrial strength
product for all your marine, household, automotive, and industrial
rust problems.Paint, Prime, Convert Rust in One StepRESTORE METAL
SURFACESExtend the life of your metal equipment by protecting it
from rust and corrosion. Rust occurs naturally when the iron in
steel oxidizes and returns to its original state, iron oxide.
Through an innovative chemical conversion process, CorrosealRust
Converterconverts rust (iron oxide) into a stable substance,
magnetite. It also primes the surface with a high quality latex
metal primer at the same time. Corroseal truly provides one step
corrosion control.CORROSEAL FEATURESWater basedrust converterwith
high quality latex metal primer Non-Flammable Non-Corrosive Easy to
apply (brush, roll, or spray) Easy to cleanup with soap and
waterECO-FRIENDLY ALTERNATIVE TO SANDBLASTINGCorroseal is the best
way to deal with rust because it is less expensive, less time
consuming, and is much more environmentally friendly than
sandblasting. Corroseal eliminates the need to sandblast rust by
chemically converting rust from iron oxide to magnetite, a black
and inert substance.Don't remove rust, convert rust!RUST CONVERTER
- RUST PRIMER - METAL PRIMERCorroseal rust converter is your best
rust treatment and corrosion control option because it meets all
your metal surface preparation needs by converting the rust and
priming the metal surface at the same time.MARINE Bridges Ships
Decks & Deck Railing Boat Trailers Ferries Oar Locks Shipping
ContainersAUTOMOTIVE Automotive Restoration Vehicle Frames
Recreational Equipment Utility Trailers Ramps Floorboards Quarter
PanelsHOUSEHOLD Garden Tools Lawnmowers Trailers Wrought iron
furniture & railings Decorative Screens Pet Housing Mailboxes
FencesINDUSTRIAL Storage & Fuel Tanks Structural Steel
Manufacturing equipment Farm Equipment Implements Fencing and Gates
Pipes
Now Available!Product DataMSDS
e.logical cleaner degreaser is a non-solvent, non-corrosive, and
non-flammable cleaner and degreaser. Easily loosens oils, grease,
and other soils for full suspension and removal from a variety of
surfaces. Mild pH to use on most water safe surfaces. Can be
diluted for all cleaning tasks. Concrete Floors Counter Tops
Equipment Soft Metals Plastic / Vinyls Pressure Washing Map &
Bucket Cleaning Engines Plexiglas Soak Tank Cleaning Hoods /
Exhaust Fans Walls Glass / FiberglassThis product meets the Green
Seal GS-37, 3rd addition standard for industrial and institutional
cleaners when packed in bulk.
M A T E R I A L S A F E T Y D A T A S H E E T PRODUCT NAME:
CORROSEAL RUST CONVERTER HMIS CODES: H F R PPRODUCT CODE: CS100 2 0
0 H ============= SECTION I - MANUFACTURER IDENTIFICATION
============ MANUFACTURER'S NAME: RODDA PAINT COMPANY ADDRESS :
6123 N MARINE DRIVE PORTLAND, OR 97203 EMERGENCY PHONE : (800)
424-9300 DATE PRINTED : 01/25/08INFORMATION PHONE : (503) 521-4300
NAME OF PREPARER : Rick Barnard ==== SECTION II - HAZARDOUS
INGREDIENTS/SARA III INFORMATION ==== VAPOR PRESSURE
WEIGHTREPORTABLE COMPONENTS CAS NUMBER MM HG @ TEMP
PERCENT---------------------------------------------------------------------------DIETHYLENE
GLYCOL ETHYL ETHER ACETATE112-15-2 .05 68F 0 - 10 GALLIC ACID
149-91-7 0 - 10 # ETHYLENE GLYCOL 107-21-1 .05 20 C 0 - 10 OSHA TLV
(vapor) ceiling 50 ppm * Indicates toxic material(s) subject to the
reporting requirements of Section313 of Title III and of 40 CFR
372. This product is believed not to contain materials listed as
carcinogens by NTP,IARC, or OSHA. The above chemical(s) meet the
criteria as defined under 29 CFR 1910 for toxicand hazardous
substances. This product may contain small amounts of materials
known to the State ofCalifornia to cause cancer and reproductive
harm. # Indicates materials listed in Section 112(b) of the Clean
Air Act. ======== SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
======== BOILING RANGE: 388 F - 417.2F SPECIFIC GRAVITY (H2O=1):
1.03VAPOR DENSITY: Heavier than air. EVAPORATION RATE: Faster than
Butyl Acetate.COATING V.O.C.: 0.69 lb/gl MATERIAL V.O.C.: 0.23
lb/glSOLUBILITY IN WATER: PartialAPPEARANCE AND ODOR: Milky
white/beige liquid with mild odor. ========= SECTION IV - FIRE AND
EXPLOSION HAZARD DATA ========= FLASH POINT: 211F METHOD USED:
TCCFLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: 0.9 UPPER: 19.4
EXTINGUISHING MEDIA: Alcohol foam, CO2 or dry chemical. SPECIAL
FIREFIGHTING PROCEDURES: For fires involving this material, do not
enter any enclosed or confined firespace without proper protective
equipment. Self-contained breathing apparatus with a full facepiece
operated in pressure-demand or other positive pressure mode to
protect against the hazardous effects of normal products of
combustion or oxygen deficiency. Water may not be effective for
fighting fires. UNUSUAL FIRE AND EXPLOSION HAZARDS: Product may
spatter if temperature of liquid exceeds the boiling point of
water.If solids ignite, toxic and irritating gases can be emitted.
Thermal decomposition of this product will produce carbon monoxide
and carbon dioxide gases. ==================== SECTION V -
REACTIBITY DATA ==================== STABILITY: | X | Stable | |
UnstableCONDITIONS TO AVOIDFreezing INCOMPATIBILITY (MATERIALS TO
AVOID)Strong oxidizing agents, strong bases, and sulfide and
sulfite compounds. HAZARDOUS DECOMPOSITION OR BYPRODUCTSNormal
combustion forms carbon dioxide and water vapor; incomplete
combustioncan produce carbon monoxide. HAZARDOUS POLYMERIZATION: |
| May occur | X | Will not occur =============== SECTION VI -
HEALTH HAZARD DATA ================== INHALATION HEALTH RISKS AND
SYMPTOMS OF EXPOSUREUse only with adequate ventilation. Do not
breathe dust or spray mist. Ensurefreah air entry during
application and drying. For spray application, sanding, abrading,
and dust cleanup, wear an appropriate properly fitted respirator
(NIOSH/MSHA TC21C approved). Follow respirator manufacturer's
directions for respirator use. If affected, remove to fresh air. If
breathing is difficult, administer oxygen.If breathing has stopped,
give artificial respiration. Get medical attention. SKIN AND EYE
CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSUREThis product contains
acids which are corrosive to the skin and eyes. Symptomsof exposure
include: redness and swelling of the eyes, burning, drying and
cracking of the skin. SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF
EXPOSUREProlonged exposure limit may result in the absorption of
harmful amounts ofmaterial. INGESTION HEALTH RISKS AND SYMPTOMS OF
EXPOSURESwallowing this product may be harmful. If swallowed induce
vomitting only ifthe person is conscious. HEALTH HAZARDS (ACUTE AND
CHRONIC)Not considered a carcinogen by IARC, NTP or OSHA. Skin -
Acute contact maycause irriation. Prolonged contact may cause
burns. Chronic exposure may cause dermatitis. Eye - Acute contact
may cause irritation and redness. Chronic exposure may
causeconjunctivitis. Ingestion may cause headache, nausea,
abdominal pains. HEALTH HAZARDS OF PREVIOUS COATINGSWARNING! If you
scrape, sand, or remove old paint, you may release lead dust.LEAD
IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVIOD EXPOSURE. Wear a NIOSH-approved respirator to control lead
exposure. Clean up carefully with a HEPA vacuum and a wet mop.
Before you start, find out how to protect yourself and your family
by contacting the National Lead Information hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead. CARCINOGENICITY: NTP
CARCINOGEN: No IARC MONOGRAPHS: No OSHA REGULATED: YesThis material
is not listed as a human carcinogenic. MEDICAL CONDITIONS GENERALLY
AGGRAVATED BY EXPOSUREInhalation may be an irritant to pre-existing
respiratory conditions. EMERGENCY AND FIRST AID PROCEDURESSKIN-
Wash exposed area with soap and water. EYES- Flush with large
amounts ofwater. ======= SECTION VII - PRECAUTIONS FOR SAFE
HANDLING AND USE ======= STEPS TO BE TAKEN IN CASE MATERIAL IS
RELEASED OR SPILLEDPersons not wearing protective equipment should
be excluded from area of spilluntil clean-up had been completed.
Stop spill at source, dike area of spill to prevent spreading, pump
liquid to salvage tank. Remaining liquid may be taken up on sand,
clay, earth, floor absorbent, or other absorbent material and
shoveled into containers. Prevent run-off sewers, streams, or other
bodies of water. WASTE DISPOSAL METHODDestroy by liquid
incineration. Material collected on absorbent material may
bedeposited in an approved landfill in accordance with local,
state, and federal regulations. PRECAUTIONS TO BE TAKEN IN HANDLING
AND STORINGStore in a cool, dry area. Keep away from heat, sparks,
and open flame. Keepcontainers closed when not in use. Use only
with adequate ventilation. OTHER PRECAUTIONSContainers of this
material may be hazardous when emptied. Since emptiedcontainers
retain product residues (vapor, liquid, and/or solid), all hazard
precautions given in this data sheet must be observed. READ AND
OBSERVE ALL PRECAUTIONS ON LABEL! ================ SECTION VIII -
CONTROL MEASURES ================ RESPIRATORY PROTECTION: If TLV of
the product or any component is exceeded, a NIOSH/MESA
jointlyapproved self-contained breathing apparatus with a full face
piece operated in pressure demand or other positive pressure mode
is advised; however, OSHA regulations also permit other NIOSH/MESA
respirators under specified conditions.(See your safety equipment
supplier). VENTILATION: Provide sufficient mechanical and/or local
exhaust to maintain exposure belowTLV(s). PROTECTIVE GLOVES: Wear
resistant gloves such as: BUNA-N EYE PROTECTION: Chemical splash
goggles in compliance with OSHA regulations are advised, unlessfull
facepiece respirator is worn. OTHER PROTECTIVE CLOTHING OR
EQUIPMENT: To prevent repeated or prolonged skin contact, wear
impervious clothing andboots. WORK/HYGIENIC PRACTICES: Wash hands
thoroughly after handling this product. ====================
SECTION IX - DISCLAIMER ===================== This information
provided as a resource only. It should not be taken as awarranty or
representation for which Rodda Paint Co. assumes legal
responsibility. The information contained is believed to be
accurate and compiled from sources believed to be reliable, it is
the responsibility of the user to investigate and verify its
validity. The user assumes all responsibility of using and handling
the product in accordance with applicable federal, state, and local
regulations.
CorrosealProduct DataPRODUCT IDENTIFICATIONCorrosealRust
Converting Primer (CS100)PRODUCTSSKU# 82320 - 1 quart jugSKU# 82331
- 1 gallon jugSKU# 82335 - 5 gallon pailSKU# 82320 - 52 gallon
drumPRODUCT DESCRIPTIONCorrosealis a water basedrust
convertercombined with a non pigmented high quality latexmetal
primer. The converter segments turn rust into a barrier layer of
black non rusting magnetite. The primer acts as a bonding agent for
oil-based intermediate and finish coatings of epoxy, enamel,
acrylic, polyurethane and moisture-cured urethane, and with water
based coatings not subject to tannin staining. Water based coatings
may require an oil based stain blocker as an intermediate
application. Corrosealis non flammable and non corrosive.DOT
shipping classification 55Universal Customs Code 3810.10Basic
UseCorrosealis recommended for use on rusted or partiallyrusted
steelsurfaces as arust converter/ paint primer, and as anetch
primeron aged tight paint of any color, and as a sealer on non
ferrous metals such as some aluminum, copper, and brass. Protects
against future rusting Can be used on welds Eliminates need to
mechanically blast to white metal in many instances Not recommended
for outside hull underwater applicationsPackagingCorrosealis
packaged in quarts, gallons, five gallon buckets and 52 gallon
drums.ThinningDO NOT THINCoverageThe actual surface condition and
thickness of rust will dictate the amount of Corrosealneeded. For
estimating purposes, 1 gallon of Corrosealcovers approximately 200
square feet.CautionsDo not use in direct contact with food or
potable water. Refer to theCorroseal MSDSand label for
precautionary information.SURFACE PREPARATIONRemove all salt, loose
rust, mill scale, dirt, grease, oil, old paint and other deposits.
Apply solvent cleaner according to manufacturer's directions and
rinse. A residue free surface is essential before coating
application begins. The surface should be a CLEAN, TIGHT
RUST.NotesDo NOT use Acetone or dishwashing detergent to
cleanrusted steelsurface. When black color appears,rust
conversionhas started. If gray areas appear apply more Corroseal
while surface is tacky.APPLICATIONBrush, roll or spray undiluted
Corrosealin a heavy white coat with no surface show through at 8-10
mils wet film thickness. When black color appears,rust
conversionhas started. Wait at least 24 hours before top coating. A
second coat of Corrosealmay be applied while first coat is still
tacky. Apply all topcoats according to manufacturers
specifications. Use oil based marine orindustrial coatingsfor best
weather protection.Application ConditionsKeep from freezing, Apply
at 45F and rising and below 100F(7-37C) and falling. Test over zinc
based coatings as some galvanizing reject Corrosealchemistry. Do
not apply onto zinc chromate or phosphates, lead, magnesium, copper
powder, graphite, borate pigments. Chromate-treated (pickled)
prefabricated steel building cold rolled perlins and gutters are to
remain dry until top coated. Cold rolled steel can require abrading
to anchor profile and degrease.Application MethodBrush roll or
spray undiluted Corrosealin a heavy white coat with no surface show
through at 8-10 mils wet film thickness.LimitationsWaterborne
topcoats subject to tannin staining must be tested 48-60 hours
before use. If tannin staining occurs, apply oil based stain
blocker or apply oil based topcoat. Always prepare a test patch to
ensure compatibility with substrate and follow-on coatings.DRY
TIMEDry time to re-coatWait at least 24 hours to top coat.TECHNICAL
SERVICESTechnical advice is available by calling Corrosealat
1-800-237-1573 or email inquiries
[email protected] more information.
Made in the USA byRodda Paint Company, Portland Oregon.
CorrosealTechnical DataPRODUCT DESCRIPTIONCorrosealis a water
basedrust convertercombined with a non pigmented high quality
latexmetal primer. The converter segments turn rust into a barrier
layer of black non rusting magnetite. Themetal primeracts as a
bonding agent for oil-based intermediate and finish coatings of
epoxy, enamel, acrylic, polyurethane and moisture-cured urethane,
and with water based coatings not subject to tannin staining. Water
based coatings may require an oil based stain blocker as an
intermediate application. Corrosealis non flammable and non
corrosive.BASIC USECorrosealis recommended for use on rusted or
partiallyrusted steelsurfaces as arust converter/metal primer, and
as anetch primeron aged tight paint of any color, and as a sealer
on non ferrous metals such as some aluminum, copper, and brass.
Protects against future rusting Can be used on welds Eliminates
need to mechanically blast to white metal in many instances Not
recommended for outside hull underwater
applicationsAvailabilitySKU# 82320 - 1 quart jugSKU# 82331 - 1
gallon jugSKU# 82335 - 5 gallon pailSKU# 82320 - 52 gallon
drumAppearanceMilky, off-white to tan liquidOdorVery mildThinningDo
not thinCoverage200 square feet per gallon @ 2.5 mil dry film
thickness. 4.9 square meters per liter.Spreading Rate8-10 mils wet
film thickness, 200-250 microns, to create optimum dry film
thickness of 2.5 mils to 3.5 milsDFT(65 to 90 microns) to cover
anchor profileCleanupSoap and water for equipment, hands, and
clothes. Clean dried spatter with lacquer thinner.PHYSICAL
PROPERTIESVOC(ATSMD 3960)60 grams per Liter, 8 oz per gallonNon
volatiles by volume31%Non volatiles by weight35%Weight per
gallon8.6 lbs, 3.91 KgpH3.0Flash point(Closed CupASTMD 56)
>200F, > 93CViscosity(Brookfield model LVF #2 spindle, 60rpm)
300 cpsHeat ResistanceResists heat aging up to 270F. Useful
properties up to 350F.UV Resistance(ASTMG-23 Ultraviolet Testing)
1000 hours - No FadingCathodic DisbondmentCorroseal Primer torusted
steeland top coated with -ASTMD4541 Wasser MoistureCure-CR-PW
Average Pull Force at Failure 1128psiShelf life(ASTMD 1849) resists
greater than 1 week at 140F and up to or over one year between 38F
and 105F, 3C and 41C. Avoid continuous direct sunlight. KEEP FROM
FREEZING. Discard after freezing.Dry time(ASTMD 1640) at 3 mils wet
film, 76 microns.Set to touch - 3 minutesCotton free - 10
minutesDry to touch - 30 minutesHard dry - 40 minutesThrough
fingernail hard - 60 minutesRejects rainwaterat 77F, 25C - No wash
off 240 minutesRecoat timeat 77F, 25C Brush / Roller 15-30 minutes,
Spray 10-20 minutes or between set to touch and dry to touch
(tacky).Top coat time24 hours minimum, up to 30 daysTECHNICAL
SERVICESTechnical advice is available by calling Corrosealat
1-800-237-1573 or email inquiries
[email protected] more information.
Made in the USA byRodda Paint Company, Portland Oregon.
