COURSE BROCHURE - PMV · 2019-08-14 · CERTIFICATE IV IN ELECTROTECHNOLOGY - SYSTEMS ELECTRICIAN UEE40611 COURSE DURATION COURSE COST LOCATION 5 Days + 5 Days + 5 Days Training centers

RTO 52698 & 51178

COURSEBROCHURE

UEE40611

CERTIFICATE IV IN ELECTROTECHNOLOGY

- SYSTEMS ELECTRICIAN

15 Years ofVocational

Training Experience

† Career Oriented

† Affordable

† Nationally Recognised

Project Management Vision

$

† To undertake work on Electrical Equipment in Hazardous Areas (EEHA) that meets the requirements of AS/NZS 60079.14 and AS/NZS 60079.17.

† To enhance students’ PLC and electrical instrumentation skills and provide exposure to process instrumentation and control used in the industry.

† To provide a pathway for electricians to Clean Energy Council Grid Connected PV Design and Installation Accreditation to design, install, configure, test and commission grid connected power supply systems.

OBJECTIVES

OUTCOME

SCOPE

Students who hold an unrestricted electrical license issued by a state or Territory and are successfully competent in both theoretical and practical training, completing all units of competency in the training package (refer http://training.gov.au/Training/Details/UEE40611), will receive the full qualification

This qualification provides competencies to: a) Select, install, test, maintain and inspect electrical equipment in hazardous

areas (EEHA) in a gas and dust atmospheres; orb) Select, install, commission, fault find and maintain electrical and

instrumentation equipment in buildings, premises, instrumentation systemsand core instrumentation equipment; or

c) Select, design and install grid-connected PV systems, develop and assessstrategies for energy loads and energy efficiency in domestic, commercial andindustrial properties and enterprises.

It includes ERAC requirements for an ‘Electrician’s licence’

CERTIFICATE IV IN ELECTROTECHNOLOGY- SYSTEMS ELECTRICIAN

UEE40611

COURSE COST LOCATIONCOURSE DURATION 5 Days + 5 Days

+ 5 DaysTraining centers atPerth & Brisbane or atClient's facility

$5,000(Perth & Brisbane, or at Client’s facility)

$2,000*(Brisbane - If eligible for Higher Skill Funding)

08 9317 2146 [email protected] www.pmv.net.au

Project ManagementVision

EEHA PATHWAY

INSTRUMENTATION AND CONTROL PATHWAY

RENEWABLE ENERGY PATHWAY

LOCATION

Delivered at one of PMV’s national training centres in Perth, Brisbane, Adelaide or at a client’s facility.

TRAININGMETHOD

COURSE STRUCTURE

Blended delivery of 60% theory and 40% practical training with equipment that you are likely to see in a typical industrial environment with

a) Electrical equipment in hazardous area (EEHA); orb) HART rated instrumentation and final control elements with PLC control

system, orc) Grid-connected PV systems and domestic, commercial and industrial energy

loads

The course includes in-class progressive assessment; short answer tests on a) Hazardous area fundamentals; equipment marking; equipment

certification; and, device interpretation orb) Hands on PLC programming, testing and fault finding, solving problems in

pressure, density, level, flow and temperature instruments, wiring,calibration and loop testing, or

c) Shading Analysis, PV install for different roof types, rails, modules, DCIsolator, pre-commissioning, commissioning and fault-finding. Loadanalysis, load efficiencies and strategies to increase the energy efficiencyusing different renewable resources.

CERTIFICATE IVIN ELECTROTECHNOLOGY- SYSTEMS ELECTRICIAN



This post-trade professional development gap training is aimed at and encourages candidates who would like to gain knowledge and “hands-on” skills in

a) Electrical equipment in hazardous area (EEHA) work in the installation,maintenance, testing and detailed inspection, or

b) PLC and process instrumentation using interface with HART fieldinstrumentation, or

c) Grid-connected PV systems design and install, strategies for energy efficiencyand assessing energy loads and energy efficiency

Pre-Requisites A current electrical license (any Australian state or territory) is required. Electrical engineers who meet the pre-requisites for electrical equipment in hazardous areas, PLC and Instrumentation units will be issued Statement of Attainment for the units they have successfully completed.

TARGETWORKFORCE




TRAININGCONTENT

You will undergo face to face to one practical training with industry experienced, qualified Electrical Professional Trainers with hands on experience in installation, inspection and remediation work in Hazardous areas and instrumentation with HART compliant field instruments and Allen Bradley PLC Control System:

EEHA Pathway The hand on training on the purpose-built hazardous areas skids include the following:

1. Principles of hazardous area classification2. Explosion-protection techniques;3. Standards and Codes of practice4. Reading and understanding hazardous area classification drawing5. Name plate reading exercise for Ex d, Ex e, Ex n, Ex i, Ex m and Ex t

techniques6. Reading Certificate of Conformity7. Specific installation requirements for different types of Ex techniques8. Equipment selection, installation, breakdowns and maintenance

requirements;9. Permit to work and safe isolations and testing;10. Making up of Ex d Barrier Gland11. Detailed inspection on Ex e/Ex d box and Ex i loop and list the required

remedial actions.

Instrumentation and Control Pathway The hand on training on the purpose-built instrumentation and control skid include the following:

1. Pressure (suppression/elevation of transmitter)2. Level Radar / Ultrasonic configuration3. Conductivity level configuration4. Flow – configuration and control including Magnetic flow meter operations5. Calibration of Temperature Transmitter with RTD and Thermocouple6. Program digital and analog PLC. Download, test and fault find PLC program

on PLC hardware7. Configuration of smart devices via HART Modem and Hand-Held

Configurator8. Reading P&ID and 2 and 4 Wire loop drawings. Verify the drawings against

as installed equipment

Renewable Energy Pathway1. Shading Analysis (Path Finder and Sun path diagram)2. PV Systems for different types3. Rails, modules, DC Isolator4. Pre-commissioning tests, Commissioning and Fault-finding5. Load analysis, loses and efficiencies6. Strategies to increase use of energy efficient methods in domestic,

commercial and industrial installations including the use of differentrenewable resources

PMV offers a small size class with flexible training to accommodate difficult rosters / work schedules.




UEENEEE038B

UEENEEE124A

UEENEEE117A

UEENEEK145A

UEENEEE101A

UEENEEE102A

UEENEEE104A

UEENEEE105A

UEENEEE107A

UEENEEE137A

UEENEEG006A

UEENEEG033A

UEENEEG063A

UEENEEG101A

UEENEEG102A

UEENEEG103A

UEENEEG104A

UEENEEG105A

UEENEEG106A

UEENEEG107A

UEENEEG108A

UEENEEG109A

PMV Training

PMV Training

PMV Training

PMV Training

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Electrical License

Participate in development and follow a personal competency development plan

Compile and produce an energy sector detailed report

Implement and monitor energy sector OHS policies and procedures

Implement and monitor energy sector environmental and sustainable policies and procedures

Apply Occupational Health and Safety regulations, codes and practices in the workplace

Fabricate, assemble and dismantle utilities industry components

Solve problems in d.c. circuits

Fix and secure electrotechnology equipment

Use drawings, diagrams, schedules, standards, codes and specifications

Document and apply measures to control OHS risks associated with electrotechnology work

Solve problems in single and three phase low voltage machines

Solve problems in single and three phase low voltage electrical apparatus and circuits

Arrange circuits, control and protection for general electrical installations

Solve problems in electromagnetic devices and related circuits

Solve problems in low voltage a.c. circuits

Install low voltage wiring and accessories

Install appliances, switchgear and associated accessories for low voltage electrical installations

Verify compliance and functionality of low voltage general electrical installations

Terminate cables, cords and accessories for low voltage circuits

Select wiring systems and cables for low voltage general electrical installations

Trouble-shoot and repair faults in low voltage electrical apparatus and circuits

Develop and connect electrical control circuits

Core Competency Standard UnitsAll Core competency standard units to be achieved Delivery Method

UEENEEM039A

UEENEEM040A

UEENEEM041A

UEENEEM042A

UEENEEM080A

UEENEEI101A

UEENEEI102A

UEENEEI103A

UEENEEI104A

UEENEEI105A

UEENEEI150A

UEENEED104A

UEENEEI124A

UEENEEI120A

UEENEEI139A

UEENEEI151A

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

Conduct testing of hazardous areas installations — gas atmospheres

Conduct testing of hazardous areas installations — dust atmospheres

Conduct testing of hazardous area installations - pressurisation

Conduct visual inspection of hazardous areas installations

Report on the integrity of explosion-protected equipment in a hazardous area

Use instrumentation drawings, specification, standards and equipment manuals

Solve problems in pressure measurement components and systems

Solve problems in density/level measurement components and systems

Solve problems in flow measurement components and systems

Solve problems in temperature measurement components and systems

Develop, enter and verify discrete control programs for programmable controllers

Use engineering applications software on personal computers

Fault find and repair analogue circuits and components in electronic control systems

Provide solutions to problems in industrial control systems

Diagnose and rectify faults in digital controls systems

Develop, enter and verify word and analogue control programs for programmable logic controllers.

Delivery Method

Delivery Method

Delivery Method

Group B – Qualification Elective Units


Group C – Qualification Elective Units

INSTRUMENTATION AND CONTROL PATHWAY




UEENEEM020A

UEENEEM021A

UEENEEM022A

UEENEEM024A

UEENEEM025A

UEENEEM026A

UEENEEM028A

UEENEEM029A

UEENEEM030A

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

Attend to breakdowns in hazardous areas - gas atmospheres

Attend to breakdowns in hazardous areas - dust atmospheres

Attend to breakdowns in hazardous areas - pressurisation

Install explosion-protected equipment and wiring systems - gas atmospheres

Install explosion-protected equipment and wiring systems - dust atmospheres

Install explosion-protected equipment and wiring systems – pressurisation

Maintain equipment in hazardous areas - gas atmospheres

Maintain equipment in hazardous areas - dust atmospheres

Maintain equipment in hazardous areas - pressurisation

Group B – Qualification Elective Units Delivery Method

EEHA PATHWAY

[email protected]



Perth10/22 Shields Crescent Booragoon, WA 6154Tel: (08) 9317 2146 and (08) 9317 2147

BrisbaneUnit 14, 720 MacArthur Ave Central, Pinkenba, QLD, 4008 Tel: (07) 3255 5952

Adelaide1042 Port Road, Albert Park, SA, 5014Tel: (08) 9317 2147


UEENEEK125A

UEENEEK148A

UEENEEC005B

UEENEEE185A

UEENEEI151A

UEENEEI152A

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

PMV Training

Solve basic problems in photovoltaic energy apparatus and systems

Install, configure and commission LV grid connected photovoltaic power systems

Estimate electrotechnology projects

Write work activity reports

Develop, enter and verify word and analogue control programs for programmable logic controllers

Develop, enter and verify programs in Supervisory Control and Data Acquisition systems

Delivery Method

Delivery Method


Group C – Qualification Elective Units

RENEWABLE ENERGY PATHWAY

*Higher Skill Funding is available from the Department of Employment, Small Business and Training (DESBT) in Brisbane andQLD Region for eligible participants only.

Student must be aware that they will no longer be eligible for another government-subsidised training place under the Higher Level Skills program once they have completed one certificate IV level or higher qualification.

Course cost is $2000* *All units taught by PMV in this qualification cost $58.33 each, the remaining course fees are distributed evenly to cover admin fees, service fees and student resources (this includes cost for RPL or CT for G105A and its 17 prerequisite units).

Contact the office for further details.

UEENEEK135A PMV TrainingDesign grid connected photovoltaic power supply systems

Documents

COURSE BROCHURE - PMV · 2019-08-14 · CERTIFICATE IV IN ELECTROTECHNOLOGY - SYSTEMS ELECTRICIAN UEE40611 COURSE DURATION COURSE COST LOCATION 5 Days + 5 Days + 5 Days Training centers