Embed Size (px)
Citation preview
Give your modules the best they deserve - CONSERV
™
Give your modules the best they deserve - ™
CONSERV
EVA ENCAPSULANTEVA ENCAPSULANT
DRALMI sasELETTRONICA PROFESSIONALE - MATERIALI E COMPONENTI
VIA CELLINI 5 - 20129 MILANO (ITALY), TEL: +39 02 [email protected] - WWW.DRALMI.IT
There is a steady growth in the energy sector in terms of both technological advancement and scale. However,
predominant use of conventional non-renewable sources of energy, coupled with the burgeoning population,
continues to increase the global carbon footprint. The clean alternative is renewable energy that can provide an
inexhaustible source of power.
At the same time, the effort towards environmental sustainability must start with a serious commitment to ™
conserve, preserve and reserve energy, using it effectively and efficiently. RenewSys , division of Positive Packaging
Industries Ltd., is the Enpee Group’s contribution to this cause.
Located at Bengaluru, India, RenewSys caters to the Renewable Energy sector through the manufacture of EVA
Encapsulant and Backsheets for Photovoltaic Modules.
Headquartered at Mumbai, India, Positive Packaging has manufacturing facilities in India, Nigeria and the UAE. It
has offices/associates in Egypt, Ghana, Kenya, Nigeria, South Africa, UAE, UK and USA providing customer service
and support worldwide.
EVA ENCAPSULANTEVA ENCAPSULANT
�P�R�O�D�U�C�T�S
�C�O�N�S�E�R�V�, the EVA Encapsulant from RenewSys, is Uniquely formulated ‘CONSERV 360 -14 FC’ offers low
manufactured using special ‘OS’ technology. 'OS' Melting Temperature, exceptionally high Luminous
Manufacturing Technology enables CONSERV to be Transmittance, high Stress-Crack Resistance, Low
produced without induced stresses allowing it to Temperature Toughness, and high UV Resistance
exhibit �U�l�t�r�a� �L�o�w� �T�h�e�r�m�a�l� �s�h�r�i�n�k�a�g�e� (Fig. 1).� resulting in high performance and durability.
CONSERV, with nearly ZERO shrinkage, results in Relatively lower melting temperature of CONSERV
advantages including net material saving (the EVA makes the lamination process more energy efficient
sheet can be cut to the exact size of the glass), no cell and productive and enhances the life of the production
mis-alignment/better aesthetics and shorter cycle equipments.
time at lamination stage compared to most market Subject to the optical transmittance value of the glass encapsulants. used in the module, CONSERV’s exceptionally high Luminous Transmittance results in higher energy CONSERV has matt finish surface on the inside and a output.specially embossed surface on the outside of the roll.
The specially embossed design of CONSERV prevents �A�P�P�R�O�V�A�L�S�:inter-blockage of the layers resulting in its
transportation and storage without masking film. ��C�O�N�S�E�R�V�3�6�0�-�1�4�F�C �� �- Verification/Certification:
Special embossing also facilitates sheet handling at the
stage of sandwich making and air evacuation at the • Performance for up to 2000 Hrs. of Damp Heat
curing stage of the lamination process.Test (DHT) by TUV Rheinland, Germany
��C�O�N�S�E�R�V� �3�6�0� �-�1�4� �F�C � is a Fast Curing UV stable EVA • UL Certification - UL 94, UL 746A & UL 746B,
encapsulant having UV cut-off length at 360 nm Certificate no 20121121 – E353124
suitable for all C-Si and many Thin-Film module
constructions. • RoHS by TUV Rheinland
A 360 - 14 FC is a fast curing, UV and weather stable Ethylene Vinyl Acetate photovoltaic encapsulant that can be used for all
Crystalline Silicon and many Thin Film photovoltaic modules.
5th Jan. 2013
R
EVA RESIN PROPERTIES:
Recommended Lamination Parameters
www.renewsysindia.com
)
Tel: +91 - 80 - 33494545, Fax: +91 - 80 - 33494552, Email: [email protected],
* Properties of un-cured material.
APPROVALS:Verified for successful performance for 2000 Hrs. Damp Heat Test by TUV Rheinland.RoHS and UL Certified. Please refer UL File No. E353124.
PACKING:Unless and until speficied, below is the standard packing of 'CONSERV'# Length/Roll : 100 meters# No of rolls/Pallet: 9# Total Linear meters/Pallet: 900# Each roll is sealed in a protective bag in a corrugated box.# Nine boxes are put on a std. Euro pallet, suitable for export
Note: Above tech information represents the typical range of properties and is believed to be correct as on date. This data should however not be used to establish
specification limits or used as basis for design. RenewSys makes no warranties and assumes no liability in connection with any use of this information.
A 360 - 14 FC
Particulars Test Method Unit Value
Storage Condition & Shelf Life: Store in undamaged original packaging, below 30°C and RH between 50 - 60%. Recommended to use within 6 months from the date of manufacture
VA Content (%) 32 - 33
MFI ASTM D 1238 g/10min @ 190°C 43 - 45
Density ASTM D 792 g/cm3 0.955 - 0.960
Melting Point ISO 11357-3 °C 60 - 61
Thickness ASTM D6988 – 08 mm 0.45 +/- 5%
Width Scale mm Up to 1240
Surface Type Visual Inside - Matt; Outside - EmbossedSupplied without masking paper.
2Tensile Strength ASTM D 638 N/mm (MPa) > 12*
Tensile Strain ASTM D 638 (%) > 600*
Shore Hardness ASTM D 2240 Shore – A 58*
Water Absorption ISO 62 – 200805 % < 0.1
Adhesion to Glass Internal N/cm > 70
Thermal Conductivity ISO 22007-4 W/Nk 0.275
Specific Heat 10°C / 80°C J/g.k 2.5° / 1.93
Shrinkage 160°C, 5 min G. plate % < 1
Optical Transmittance ASTM E 424 % > 92
UV Cut Off Wavelength ASTM E 424Visual IR Spectrophotometer nm 360
Refractive Index ISO 489 1.480
Dielectric Strength ASTM D 149 kV/mm > 25
Volume Resistivity ASTM D 257 ohm cm > 1.83 x 10^16
Gel Content Soxhlet method % > 80
Evacuation Time Minutes 3 - 5
Lamination Time Minutes 7 - 10
Curing Temp. °C 145 - 152
EVA ENCAPSULANTEVA ENCAPSULANT
SHEET PROPERTIES:
PRODUCT DATA SHEET
• Proven raw materials
EVA ENCAPSULANTEVA ENCAPSULANT
• Fast curing
• Ultra-low Thermal Shrinkage
• Exceptionally high Light Transmittance
• No masking film - unique surface structure
• RoHS and UL Certified
• 2000 Hrs. Damp Heat Test - verifiedsuccessfully by TUV Rheinland
BACKSHEETS
Factory: Renewsys (Division of Positive Packaging Industries Ltd.)
Plot No. 21 & Part 22, Bommasandra Jigani Link Road Industrial Area,
Taluk Anekal, Bengaluru - 562 106, Karnataka, India.
Tel.: +91 - 80 - 33494545, Fax: +91 - 80 - 33494552
Email: [email protected], Web: www.renewsysindia.com
Corporate Office: 3rd Floor, A Wing, Great Eastern Summit, Plot No. 56,
Sector 15, CBD Belapur (E), Navi Mumbai - 400 614, Maharashtra, India.
Tel.: +91 - 22 - 39211400, Fax: +91 - 22 - 39211430
Web: www.positivepackaging.com
Registered Office: 98, Jolly Maker Chambers No.2, 225, Nariman Point,
Mumbai - 400 021, Maharashtra, India.
Tel.: +91- 22 - 30011700, Fax: +91- 22 - 22023774
Overseas Contacts:
Country City Name Tel. Email
Egypt Cairo Mahmoud Darwish +20 - 2 - 22585514 [email protected]
Ghana Accra H S Mahesh +233 - 246558816 [email protected]
Kenya Nairobi Narendra Das +254 - 20 - 4447315 [email protected]
Nigeria Lagos Jayesh Upadhyay +234 - 1 - 4968340 / 1 [email protected]
South Africa Durban Avinash Hiranandani + 27 - 31 - 2022096 [email protected]
UAE Dubai Parwez Izhar +971 - 4 - 8861242 [email protected]
UK London Anil Sadhwani +44 - 2079357124 [email protected]
USA New York Ashok Melwani +1 - 516 - 2362773 [email protected]
http://www.renewsysindia.com/contactus.html
