FLASHLIGHT ANSI STANDARDS...• Handheld flashlight Model "Heads-Up" Cat No 2600, for use with four (4) size "AA", 1.5V each, battery cells by Eveready No E91 or Duracell MN1500 or

FLASHLIGHT ANSI STANDARDSWhile Pelican was one of the first manufacturers to use quantifiable test procedures, the need was recognized to develop a common language that customers could use to select the right flashlight for their specific needs.

As a result, the American National Standards Institute (ANSI) with input from the flashlight industry, developed performance standards and symbols to effectively communicate a flashlight's features and benefits.

Resulting ANSI/NEMA FL 1 Standards include the six criteria described below:

LIGHT OUTPUTLight Output is the total luminous flux. It is the total quantity of emitted overall light energy as measure by integrating the entire angular output of the portable light source. Light output in this standart is expressed in units of lumens.

RUN TIMERun Time is defined as the duraton of time from the initial light output value – defined as 30 secons after the point the device is first turned on – using fresh batteries, until the light output reaches 10% of the initial value.

BEAM DISTANCEBeam Distance is defined as the distance from the device at which the light beam is 0.25 lux (0.25 lux is approximately the equivalent of the light emitted from the full moon "on a clear night in an open field").

PEAK BEAM INTENSITYPeak Beam Intensity is the maximum luminous intensity typically along the central axis of a cone of light. The value is reported in candela and does not change with distance.

IMPACT RESISTANCEImpact Resistance is the degree to which a device resists damage from dropping on a solid surface.

IPX4 WATER PENETRATION RATINGS

IPX4 - Water Resistance - Water splashed against the device from any direction shall have no harmful effects.

IPX4 / IPX7 WATER PENETRATION RATINGS

IPX7 - Water Proof - Ingress of water in quantities causing harmful effects shall not be possible when the enclosure is temporarily immersed in water under standardized conditions of pressure and time.

IPX8 - Submersible - Ingress of water in quantities causing harmful effects shall not be possible when the enclosure is continuously immersed in water under conditions which shall be stated by manufacturer, but which are more severe than for IPX7.

https://www.carid.com/pelican/

https://www.carid.com/work-lights.html

ANSI (AMERICAN NATIONAL STANDARDS INSITUTE)

These standards are accredited by ANSI, which is a private non-profit organization that oversees thedevelopment of voluntary consensus standards for products, services, processes, systems, and personnel in the United States. The organization also coordinates U.S. standards with international standards so American products can be used globally.

GLOSSARY OF TERMS

Candela - A unit of measurement of the intensity of light that is, power emitted by a light source in a particular direction.

Lux - The unit of luminous flux in the International System, equal to the amount of light given out through a solid angle by a source of one candela intensity radiating equally in all directions.

Lumen - A unit of measurement of the amount of brightness that comes from a light source. Lumens define "luminous flux," which is energy within the range of frequencies we perceive as light.

Integrating Sphere - An integrating sphere is a measurement device with an entrance port that can accept all the directional light output of the device under test, or can totally enclose the device itself.The walls of the sphere should be highly diffuse with high reflectivity (>80%) and the spectroradiometer should be shielded from direct view of the device under test by a baffle system.

IP (Ingress Protection) - Ingress Protection (IP) ratings specify the environmental protection the enclosure provides. The IP rating normally has two numbers (IPXX). The first number represents protection from solid objects or materials (dust) where the second number represents protection from liquids (water). With the IP rating IP 54, 5 describes the level of protection from solid objects and 4 describes the level of protection from liquids.

Certificate of ComplianceCertificate: 1640694 Master Contract: 154507

Project: 2657098 Date Issued: January 3, 2014

Issued to: Pelican Products, Incorporated

The products listed below are eligible to bear the CSA Mark shown

Ezio Migliozi

Issued by: Ezio Migliozi

PRODUCTSCLASS 9098 01 - MISCELLANEOUS - For Hazardous Locations

Class I, Div 2, Groups A, B, C and D (Non-Incendive); Class II, Div 2, Groups F and G; Class III.

• Handheld flashlight Model "Pocket Sabre 2C" Cat No 1820, to be used with two (2) "C" size batteries 1.5Vper cell by "Eveready No E93 or Duracell MN1400 or Ray-O-Vac No 813 and lamp Cat. No.1804, P/N1803-350-000. Temp Code T3C. Ambient: –35°C to +40°C.

• Handheld flashlight Model "Magnum Plus-2AA" Cat No 2340 to be used with two (2) "AA" size batteries1.5V per cell, by Eveready No E91 or Duracell MN1500 or PC1500 or Ray-O-Vac Al-AA or 815 with lampModule CAT # 2304; Temp. Code T3C. Ambient: –35°C to +40°C.

• Handheld flashlight Model "Heads-Up" Cat No 2600, for use with four (4) size "AA", 1.5V each, batterycells by Eveready No E91 or Duracell MN1500 or PC1500 or Ray-O-Vac No 815 and light bulb Cat No 2604or 2605, Temp Code T3C.

• Handheld flashlight Cat No 8040 M10 to be used with two (4) "C" size batteries, 1.5V per cell by EvereadyNo E93 or Duracell MN1400 with Lamp Module Cat. No. 8044, P/N 8043-350-000; Temp. Code T3C.Ambient: –35°C to +40°C.

Class I, Div. 2, Groups A, B, C and D (Non-incendive); Class II, Div. 2, Group G:

Certificate: 1640694 Master Contract: 154507


• Handheld flashlight Model "Super Pelilite" Cat No 1800, to be used with two (2) "C" size batteries, 1.5Veach per cell by "Eveready No E93 or "Eveready No CH35 or Duracell MN1400 or PC1400 or Ray-O-VacAL-C or No 814 and lamp P/N 1804. Temp Code T3C.

• Handheld flashlight Model "Mitylite" Cat No 1900, to be used with two (2) "AAA" size batteries, 1.5V eachper cell by "Eveready" No E92 or Duracell MN2400 or PC2400 and reflector Module P/N 1904. Temp. CodeT3C.

• Handheld flashlight Model "Super Sabrelite" Cat No 2000, to be used with three (3) "C" size batteries, 1.5Veach per cell by "Eveready" E93 or "Eveready" No CH35 or Duracell MN1400 or PC1400 or Ray-O-Vac AL-C or No 814 with lamp module P/N 2004. Temp Code T3C.

• Handheld or clip-on flashlight Model "VersaBrite" Cat No 2250 to be used with two(2), "AA" size batteries,1.5V each by Eveready No E91 or Duracell MN1500 or PC1500 or Ray-O-Vac No 815 and lamp module CatNo 2204. Temp Code T3C. Ambient: –35°C to +40°C.

• Handheld flashlight Model "Mitylite Magnum" Cat No 2300 to be used with two (2) "AA" size batteries,1.5V each by "Eveready" No E91 or Duracell MN1500 or PC1500 or Ray-O-Vac No 815 with lamp moduleCAT # 2304; Temp. Code T3C.

• Handheld flashlight Model "StealthLite" Cat No 2400, to be used with four (4) "AA" size batteries, 1.5Veach by "Eveready" No E91 or Duracell MN1500 or PC1500 or Ray-O-Vac No 815 with lamp module CatNo 2404; Temp. Code T3C.

• Handheld flashlight Model "Stealthlite Rechargeable" Cat No 2450 to be used with four (4) "AA" sizebatteries, 1.5V each by Eveready No E91 or Duracell MN1500 or PC1500 or Ray-O-Vac No 815 orrechargeable battery pack Cat No 2469; used with lamps module CAT # 2454; Temp Code T3C.

• Handheld flashlight Model Heads-Up Cat No 2600, for use with four (4) size AA, 1.5V each, battery cellsby Eveready No E91 or Duracell MN1500 or PC1500 or Ray-O-Vac No 815 and light bulb Cat No 2604 or2605; Temp Code T3C

• Handheld lantern Model "King Pelican Lite" Cat No 4000, to be used with eight (8) size "D" Eveready E95or Duracell MN1300 or PC1300 or Ray-O-Vac AL-D or No 813 battery cells, 1.5V each, with lamp Cat No4003. Temp Code T3C. Ambient: 0°C to +40°C.

Certificate: 1640694 Master Contract: 154507


APPLICABLE REQUIREMENTS

CAN/CSA C22.2 No. 0-M91 - General Requirements - Canadian Electrical Code, Part II

CAN/CSA C22.2 No. 213-M1987 - Non-Incendive Electrical Equipment for Use in Class I, Division 2Hazardous Locations

CEC Part I - Sec 18.252 - As a guide.

CAN/CSA C22.2 No. 25-1966 - Enclosures for Use in Class II, Groups E, F and G Hazardous Locations

CAN/CSA-C22.2 No. 157-92 - Intrinsically Safe and Non-Incendive Equipment for Use in HazardousLocations

MARKINGS

- Company name;

- Model number;

- Serial number;

- Hazardous locations designation;

- CSA Monogram;

- Temperature Code Rating;

- Ambient temperature range.

- Battery Type;

- Lamp Type or Lamp Module Cat. No.

- Battery pack Cat. No.

- The following warnings shall appear in Operating Instructions:

"WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITYFOR USE IN HAZARDOUS LOCATIONS”

"WARNING - EXPLOSION HAZARD - BATTERIES MUST ONLY BE CHANGED AND/OR CHARGEDIN NON-HAZARDOUS LOCATIONS"

IECEx Certificate of Conformity

INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres

Certificate No.:

Status:

Date of Issue:

Applicant:

Electrical Apparatus: Optional accessory:

Type of Protection:

Marking:

j IECEx TSA �6.0021X

Current 2011-10-06

Pelican Products Inc.

Pelican Torches

Exe ib I Ex ia

L 1 #1930 - Ex ia llC T4 IP65

issue No.:2 [

Mitylite 2A #1900 - Exe ib llC T4 IP67 Mitylite 2AA #2340 - Exe ib llC T4 IP65 Pocket Sabrelite #1820 - Ex e ib llC T3 IP65 M10 #8040 - Exe ib llC T3 IPSO Sabrelite #2000 - Exe ib llC T4 IP67 IECEx TSA 06.0021X

Approved for issue on behalf of the IECEx Certif cation Body:

Ujen Singh

Position: Quality and Certification Manager

Signature: (for printed version)

Date:

1. This certificate and schedule may only be reproduced in full. 2. This certificate is not transferable and remains the property of the issuing body.

Test l'l. U 5 T R A L, l li

Certificate No.:

Date of Issue:

Manufacturer:

Manufacturing location(s):


IECEx TSA 06.0021X

2011-10-06

Pelican Products Inc.

Issue No.: 2

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.

STANDARDS: The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

IEC 60079-0 : 2004 Edition: 4.0 IEC 60079-11 : 1999 Edition: 4 IEC 60079-7: 2001 Edition: 3

Electrical apparatus for explosive gas atmospheres - Part 0: General requirements

Electrical apparatus for explosive gas atmospheres - Part 11: Intrinsic safety 'i'

Electrical apparatus for explosive gas atmospheres - Part 7: Increased safety 'e'

Certificate No.:

Date of Issue:

EQUIPMENT:


IECEx TSA 06.0021X

2011-10-06 Issue No.: 2

Schedule

Equipment and systems covered by this certificate are as follows:

The torch A plastic face cap is fitted with a polycarbonate lens O rings provide -

sealing between the face cap and the battery enclosure. The description of the torches is shown in the table below:

Torch Model Switch arrangement

L1 #1930 Rubber sealed push button Mitylite 2MA On or off by screwing face cap

#1900 Mitylite 2AA #2340 Rubber sealed push button

Sabrelite #1820 On or off by screwing face cap M10#8040 Rubber sealed push button

Sabrelite #2000 On or off by screwing face cap

CONDITIONS OF CERTIFICATION: YES as shown below:

Vent arrangement Cell

No F Vent path near theface · 2 AA

cap Capped vent hole 2C

A vent hole under the vinyl sleeve

Bulb

LED Xenon gas filled bulb Xenon gas filled bulb Xenon gas filled bulb

Xenon gas filled bulb

Capped vent hole 3C Xenon gas

Only the Energizer Industrial (EN series) AA size and C size alkaiine cells, Energizer (E series) C size alkaline cell, Energizer (E92) AA size, Energizer A76 BP2 alkaline cell and Vinnie L 1154 cell can be used in these torches. Conditions of Certification permitted by Issue 1: Only the Energizer Industrial (EN series) C size alkaline cell, Energizer (E series) C size alkaline cell and Panasonic LR14(XJ) C size cell can be used in Sabrelite #2000 torch. Refer annexe of issue 02 for the conditions of certification.

Certificate No.:

Date of Issue:


IECEx TSA 06.0021X

2011-10-06 Issue No.: 2

DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):

\Variation permitted by issue 1: Added Panasonic LR14 (XJ) C size battery into Sabrelite Model 2000 battery list. !Variation permitted by issue 2: )Added AA DURACELL Alkaline, LR03 batteries. Changed IECEx auditing body from FMG to FME

IECEx Certificate of Conformity Annexe

Annexe for Certificate No.: IECEx TSA 06.0021X

list to Issue 00 of this Certificate:

Assessed in test report AU/TSNExTR06.0025/0 l (27493A, TestSafe).

Document No.

LI #1930 1933-920-100 1933-925-000 1933-925-110 1933-961-110 l 936-350-123 1931-921-CLR 1953-341-000 1930 Aus Engraving

2AAA #1900 1900-015-110 1903-302-000 1903-321-000 l 903-341-000 1903-350-000 1903-920-100 I 921-920-110 1971-925-110 1973-331-000 1976-350-000 1900-001-AUS Pocket Sabrelite #1820 1803-321-000 1803-341-000 1803-351-000

I 804-401-000 1821-941-000 1823-920-100 1823-943-000 1823-944-000 1823-946-000 1.823-965-110 1826-331-000 1820-001

Document Title

Lens 1930 LED Light l 930 Reflector Shroud 1930 LED Cover, Switch 1930 LED

Tray & Switch 1930 UL 1930 L 1

LI AUS Approval Engravings 1930 L l Insert Tool #171-3

2AAA Pad, Mitylite

1900

Cat# 1904 Module Mitylite Lens, 1920 & 2250

2AAA Shroud, Retainer, Mitylite

1900 AUS

Pelilite Bat. Cont.

Cat# 1804 Lamp Module, Pocket Sabre/Peli lite Foam Pad, Pelilite

1820 Pocket Sabre Lens, 1800 & 1820 Peli/Pocket Sabre/Stealth Land End Sidekick Lite

Slide Sidekick Lite Sidekick Lite

Shroud, Rubber Pocket Sabre Retainer, Sidekick Lite

Label Pocket Sabre

Issue No.: 02

Issue Date

B 2001/02/02 PR 2000/07117 A 2001/06/28 B 2002/12/16 D 2005/06/10

PR 2005/12/13 B 2002/10/24 A 2006/03/24

PR 2003/01/24 A 1997/10/24 A l 996/07/02 J 2002/08/28 c 2000/09/19 H 2003/04/21

PR 2003/01/27 8 2003/10/03 E 2000/06/29

PR 2003/02/05 8 2006/04/07

A 1996/07/08 D 2002/11/13 A 2003/07/25

F 2001/04/16 F 2005/10/17 E 2003/04/24

PR 1999/07/05 PR 1999/07/05 PR 1999/07/05 c 2001/02/23 8 2002/04/29 F 2006/04/07



Document No.

2AA #2340

2303-351-000 23 03-920-100 2303-920-110 234 I-921-000 2346-620-110 2350-961-110 2353-321-000 234I-921-l lOE

M8 #8030 & MlO #8040

2403-3 22-000 3103-322-000 8030-920-000 8031-921-000 8033-331-000 8033-341-000 8033-342-000 8033-345-000 8033-960-IIO 8033-980-110 8036-620-I I 0

8043-331-000 8043-350-000 8043-34 I-OOO 8043-342-000 8043-346-I IO 8043-941-110 8043-964-110 805 I-92 I -000 8053-321-000 8053-921-1 lO 2 Sheets 8053-961-CLR 8053-962-110 8030-000-AUS 8043-001-AUS Sabrelite #2000

2000-000-000 2001-940-000 2 sheets 2001-944-000

Document Title

Module, Cat#2304 Lens 2270 & 2300 2270 & 2300 Lens Over Mold

Plus 2AA Push Button Switch IPlT With Switch Boot, M-7 Vent Seal, 2350 2AA Rechrg. CE ATEX Approval Markings Mitylite Plus 2AA

Switch M-8

M-8 Retainer, M8 Black

End Plate, Contact

M8/IO 8030 Sleeve M8 Switch, Push Button M8/l 0 (with Locking) EX-93 Retainer. MIO/I I Black

Module, MIO Screw, M8/MIO Switch Stud, Retainer, MIO

M8/M IO/MI I Lens & Shroud Ml 0 Ml 0

MIO/Ml l Mil M 11

Switch Boot, M-11 8050 Sleeve M8 AUS Approval Engraving MIO AUS

Sabrelite Body, Sabrelite

Slide - Sabrelite

Issue No.: 02

Issue Date

F 2001/02/23 E 2003/04/21

PR 2004/04/15 A 2002/04/15 A 2002/06/l 7 c 1999/02/03

PR Undated c 2006/04/07

PR 2001/07/16 PR 2001/07/16 PR 2000/09/13 D 2002/03/26 G 2003/08/05 B 2002/04/08 A 2002/04/04 D 2003/09/04 B 2005/10/05 B 2002/02/04

PR 2003/04/25

1 2003/08/05 B 2000/06/I 5 D 2003/05/13

PR 1999/12/07 A 2001/06/05 A 2002/07/02 A 2001/04/05 D 2003/07/25

PR 200 I/07 /I 6 A 2000/04/26 F 2005/08/01 F 2005/10/05 B 2006/04/07 A 2006/04/07

L 2003/07/17

Q 2005/12/05 A 1996/ I l /19



Document No. Document Title

2001-946-000 Sabrelite 2001-947-110 Chamber Sabrelite 2003-321-000 Sabrelite 2003-341-000 Spring Clip, Super Sabrelite 2003-342-000 Sabrelite 2003-343-000 Valve, PUV 2013-344-000 Retainer 2003-345-000 Pin 2003-351-000 Lamp (Stamped Aluminum), Sabre

2003-920-100 2000 Lens M8, M 10, & 2000 2003-920-110 Lens & Shroud Assy., 2000 2003-942-110 PUV 2004-401-000 Foam Pad, Sabrelite 2006-3 31-000 Retainer & Assembly Sabrelite 2000-001 Label, FM, CSA, UL & MSHA Approvals

Sabrelite


Assessed in test report AU/TSA/ExTR06.0025/02 (30371, TestSafe).

Document No. Sheets Document Title

2000-000-CLR I 2000 Sabrelite

Issue No.: 02

Issue Date

E 2003/07/21 G 2001/11/07 A 1996/11/19 I 2002/07/09 F 2001/03/02

PR 2002/07/22 c 2003/01/17 F 2002/02/14 0 2002/05/08

K 2004/07/14 B 2002/07/22

PR 2002/07/22 c 2003/12/01 J 2004/08/05 G 2006/03/24

Issue Date

2007/05/08

2001-940-CLR I Pelican 2000 SabreLite PR 2005/09/30 2106-300-110 I 2006-342-000

2001-945-CLR

2003-980-170 1

8053-920-100 I 2003-942-CLR I 2006-331-000 I

2000-001 1

Lanyard Assy with

Sabre Polarity Chamber, Super Sabrelite Lens

PUV Retainer & Sabrelite Label, FM, CSA, UL & MS HA Approvals

Sabrelite

PR 2004/11119 PR 2007/07/31 PR 2005/11/30

00/00/00 B 2007/05/24

2008/03/31 K 2007/03/22

H 2007/12/10

llE,CEx Certificate of Conformity Annexe


Conditions of Certification to Issue 02 of this Certificate:

Issue No.: 02

I. The AAA DURACELL Alkaline, LR03 cells are acceptable to be used in PELICAN MityLite # 1900.

2. Refer the instruction sheet regarding the backing off of lens housing when switching off the torch.


Assessed in test report AU/TSA/ExTRI 1.0032/00 (32578, TestSafe).

Document Sheets No.

LI #1930 1936-350- 2 CLR Mitylite 2AAA #1900 1900-015- I CLR 1906-351- I 000 1903-321- I 000 1903-920- l

100 1922-920- 1 000 1971-925- l 110 1973-331- I

000 1900-001 I Pocket Sabrelite # 1820

1823 321- I

000

Document Title

CERTIFICATION DRAWINGS

Battery Tray & Switch Assy, 1930

1900 Pelican Assembly

Lamp Assembly Mitylite

O'Ring 1900

Lens, 1900

1900 Blank Body

Shroud, Mitylite

Retainer, Mitylite

1900 Insert

0-ring, Lens I 820 Pocket Sabre

Issue Date

F 2008/04/24

A 2010/01/25

A 2009/04/13

c 2009/l l/10

K 2009/04/17

A 2010/02/22

c 2009/04/13

G 2009/04/13

E 2011/08/12

PR 2000-07-02


Annexe for Certificate No.: IECEx TSA 06.0021X Issue No.: 02

Document Sheets No.

1823-920- I 100

1823-920- I l l O 1820-001 I

Mitylite 2AA #2340

2303-353- 1

000

2303-920- 1 100 2341-921- 2

l lO 2346-620- 2

110 2353-961- I 110

2340-001 I

MIO #8040

8040-000- I CLRA 3103-322-

000

8066-342- 2 000

8046-620- 1 110

8063-331- 1 000

8063-342- I 000

8063-941- 1 CLR 8041-923- I CLR 2003-321- 1 000

Document Title

Lens, 2400 Round

1820 Shroud Overmold

Approval Label Pocket Sabre

Lamp Module, Cat #2304

Lens 2270 & 2300

Body 2340 MITYUTE Plus 2AA

2340 Switch Assembly

2340, Boot, Switch

Approval Markings MityLite 2340

8040, IEC Light Assembly

0-ring, Battery

Assembly, End Cap Spring

8040 Switch

Retainer

Stud, Charging

Lens & Shroud, Assy, 8060

8040, Pelican New Body

0-ring, Super Sabrelite

Issue Date

G 2009/06/03

B 2009/12/0l

H 2011/08/31

J 2007/03/12

F 2009/02/25

G 2003/10/27

c 2009/02/25

F 2009/02/25

G 2011/08/31

PR 2010/01/15

A 2010/04/16

PR 2008/05/01

PR 2010/03/08

A 2010/04/22

A 2010/04/23

A 2010/04122

PR 2009/12/22

B 2009/04/17


Annexe for Certificate No.: IECEx TSA 06.0021X Issue No.: 02

Document Sheets No.

8063-921- 1 CLR 8063-961- 2

110 8043-001-AUS Sabrelite #2000

2000-000-

CLR 2003-980- 1

170 2003-321- 1

000

2003-343- I

000 8053-920- I

100

2003-921- I

110 2003-942- I

CLR 2006-331- 1 000 2000-001 1

1823-311- 2 000

Document Title

8060 End Cap

Switch Boot

Ml 0 IEC Approval

2000 Sabrelite Assembly

Polarity Chamber, 2000

0-Ring Super Sabrelite

Valve, PUV

Lens

Lens & Shroud Assy,. 2000

CAP, PUV

Retainer And Clip Assembly Super Sabrelite

2000, Sabrelite REFERENCE DOCUMENTS Pocket Sabre 1820 Instructions

Issue Date

A 2010/04/22

c 2010/04/27

c 2011/07/11

p 2009/05/26

J 2010/05/06

B 2009/04/17

A 2009/08/10

B 2007/05/24

A 2007/05/24

B 2008/03/31

K 2007/03/22

J 2011/08/12

B 2011/07/--

lntertek ETL SEMKO

AUTHORIZATION TO MARKThis authorizes the application of the Certification Marks shown below to the models described in the Products(s) Covered section when made in accordance with the conditions set forth in the Certification Agreement and Listing Report. This authorization also applies to the multiple listee model(s) identified on the correlation page of the Listing Report.

Applicant: Pelican Products

Party Authorized To Apply Mark: Same as Applicant

Report Issuing Office: lntertek Cortland Facility

Report No.: 3094552-H01

Product Covered: Flashlight Mity Lite Models: 2300 and 2340 For Use In: Class I, Division 1, Groups C and D Hazardous Locations When used with: 2 Energizer Type E91 AA batteries and Bulb assembly #2304Operating Temperature Code: T3

Description: The products covered by this report are flashlights for use in Class I, Division 1, Group C and D Hazardous Locations. The flashlight contains 2 AA batteries. Model 2300 is provided with a screw tight mechanism to turn unit on. Model 2340 is provided with a push button switch to turn unit on.

Standard: Electric Flashlights and Lanterns for Use in Hazardous (Classified) Locations (UL 783, Sixth Edition, Dated: April 28, 2003)

This document is the property of lntertek Testing Services and is not transferable. Only the Applicant may reproduce this document. The certification mark(s) may be applied only at the above noted location of the Party Authorized To Apply Mark .

... us

William T. Starr, Certification Manager

Control Number: c.O q /d 25 This document supersedes all previous Authorizations to Mark for the noted Report number.

lntertek Testing Services NA Inc.

lntertek ETL SEMKO September 1, 2006

SUBJECT:

Dear Mr. Kang:

lntertek Job No. lntertek Report No.

3094552 3094552-H01

lntertek has completed our evaluation of your Flashlights, Models: Mity Lite 2300 and 2340.

Enclosed is one copy of the Listing Report for your records. A copy of this Listing Report will be sent to the lntertek Field Representative for use at the time of the Initial Plant Inspection. Please be advised that distribution of copies to the manufacturer(s) is your responsibility.

You or your manufacturer will receive the Authorization to Mark form from our Follow-Up Service Department. 'This form will be forwarded directly to your manufacturing facility. The inspection of this product will be included with your next regularly scheduled follow-up service visit.

Project Engineer lntertek Cortland Office

Job No. 3094552

LISTING REPORTINTERTEK ETL SEMKO

3933 US ROUTE 1 1 CORTLAND, NY 13045

REPORT NO. 3094552-H01 INSPECTION, TESTS AND EVALUATION

OF FLASHLIGHTS

RENDERED TO

PELICAN PRODUCTS

Issued: September 1, 2006 Revised: NA

GENERAL: This Report gives the results of the inspection, tests, and evaluation of Flashlights (Models: Mity Lite 2300 and 2340). The product was investigated for compliance with the applicable requirements of the standard for Electric

and Lanterns for Use in Hazardous Locations Sixth Dated: The investigation was begun on 05/12/06 and completed on 09/01/06. Prototype samples, in good condition were provided bythe client on 03/16/06, 05/12/06, and 06/02/06 and tested at INTERTEK ETL SEMKO's Cortland, NY facility.

Electric and Lanterns for Use in Hazardous Locations Sixth Dated:

Report No. 3094552-H01 Pelican Products

INTERTEK ETL SEMKO

TABLE OF CONTENTS

Main Report 1 --> 1 3

Markings M1

Illustrations 1 1 --> 17

Evaluation of Unlisted Components C1 --> C2

Revisions R1

Issued: 09/01/06 Revised: NA


PRODUCT COVERED:

Flashlight Mity Lite Models: 2300 and 2340

INTRODUCTION

For Use In: Class I, Division 1, Groups C and D Hazardous Locations When used with: 2 Energizer Type E91 AA batteries and Bulb assembly #2304 Operating Temperature Code: T3

PRODUCT DESCRIPTION:


The products covered by this report are flashlights for use in Class I, Division 1 , Group C and D Hazardous Locations. The flashlight contains 2 AA batteries. Model 2300 is provided with a screw tight mechanism to turn unit on. Model 2340 is provided with a push button switch to turn unit on.

RATINGS:

Product:

Mity Lite 2300 Mity Lite 2340

3Vdc 3Vdc

14A 14A

Code: T3 T3


TEST PERFORMANCE


A sample of the product was tested in accordance with the standards for Electric and Lanterns for Use in Hazardous Locations Sixth Dated:

The following tests were conducted by: UL under report E184884.

TEST DESCRIPTION

Spark Ignition Test

Battery Output Test

The following tests were performed:

TEST DESCRIPTION

Temperature Test

30 Foot Drop Test

Impact Test

Thermanl Endurance to Heat

Thermal Endurance to Cold

STANDARD

UL 78 3

UL 78 3

STANDARD

UL 78 3

UL 78 3

UL 78 3

UL 78 3

UL 78 3

Results of the tests indicate the specimens conform to applicable test criteria .

CLAUSE

37

38

CLAUSE

20

3 3

34

35

36


CONCLUSION


A representative sample of the product covered by this report has been evaluated and found to comply with the applicable requirements of the standards for Electric and Lanterns for Use in Hazardous Locations Sixth Dated:

Report prepared by:

, ·' -�- /�) / / /

, ' .. ,,. • / . / .. '·· -- ! � -? ' :.:�"'°

Project Engineer

Cortland review/approval of Report by:

/fl�·u<Vq Mike Spector Staff Engineer


GENERAL INFORMATION


The Applicant and Manufacturer have agreed to produce, test and label ETL Listed products in accordance with the requirements of this Report. The Manufacturer has also agreed to notify INTERTEK ETL SEMKO and to request authorization prior to using alternate parts, components or materials.

COMPONENTS

Components used shall be those listed in the INTERTEK ETL SEMKO report covering the products specified in the index including any amendments and/or revisions.

LISTING MARK

The ETL listing mark applied to the products shall either be separable in form, such as labels purchased from INTERTEK ETL SEMKO, or on a product nameplate or other media only as specifically authorized by INTERTEK ETL SEMKO. Use of the listing mark is subject to the control of INTERTEK ETL SEMKO.

MANUFACTURING AND PRODUCTION TESTS

Manufacturing and Production Tests shall be performed as required in this Report.

FOLLOW-UP SERVICE

Periodic unannounced audits of the manufacturing facility shall be scheduled by INTERTEK ETL SEMKO. An audit report shall be issued after each visit. Special attention will be given to the following:

1. Conformance of the manufactured product to the descriptions in this Report.2. Conformance of the use of the ETL mark with the requirements of this Report and the Listing, Labeling, and Follow-up

Service Agreement. 3. In-plant quality control procedures and personnel. 4. Manufacturing changes. 5. Performance of specified Manufacturing and Production Tests.

In the event that the INTERTEK ETL SEMKO representative identifies non-conformance(s) to any provision of this Report, the Applicant shall take one or more of the following actions:

1. Correct the non-conformance. 2. Remove the ETL Listing Mark from non-conforming product. 3. Contact the issuing1'Jroduct safety evaluation center for instructions.


GENERAL REQUIREMENTS AND DEFINITIONS

Issued: 09/ 01/06 Revised: NA

- A component part, which has been previously evaluated by an accredited certification body with restrictions and must be evaluated as part of the basic product considering the restrictions as specified by the Conditions of Acceptability.

Listed - A component part, which has been previously Listed or Certified by an accredited Certification Organization with no restrictions and is used in the intended application within its ratings.

Unlisted - A part that has not been previously evaluated to the appropriate designated component standard. It may also be a listed or recognized component that is being used outside of its evaluated listing or component recognition.

Critical -An essential part, material, subassembly, system, software, or accessory of a prqduct that has a direct bearing on the product's conformance to applicable requirements of the product standard.

Construction Details - For specific construction details, reference should be made to the following photographs and descriptions. All dimensions are approximate unless specified as exact or within a tolerance. In addition to the specific construction details described in this Report, the following general requirements may also apply as applicable.

1 . Mechanical - Components such as switches, fuseholders, connectors, wiring terminals and display lamps are reliably mounted and prevented from shifting or rotating by lockwashers, starwashers, or the mounting format.

2. Corrosion Protection - All ferrous metal parts are suitably protected against corrosion by painting, plating or theequivalent.

3. of Live Parts - All uninsulated live parts in primary circuitry are housed within a metal/plastic enclosure constructed such that any openings are not penetrable by the probe specified in the above-referenced Standard.

4. - The markings are molded into enclosure, reference markings page M1 for content.


MANUFACTURING AND PRODUCTION TESTS

Issued: 09/01 /06 Revised: NA

The manufacturer agrees to conduct the following Manufacturing and Production Tests as specified:

Tests

No manufacturing or production line tests are required


CORRELATION PAGE FOR MULTIPLE LISTINGS


The following products, which are identical to those identified in the Product Description except for model number and Listee name, are authorized to bear the ETL label under provisions of the INTERTEK ETL SEMKO Multiple Listing Program.

MULTIPLE LISTEE:

BASIC LISTEE:

MANUFACTURER:

PRODUCT:

NONE

Pelican Products

Same as Basic Listee

Mity Lite

MULTIPLE LISTEE MODEL NUMBER: BASIC LISTEE MODEL NUMBER: BASIC LISTEE ORDER NUMBER:

NONE 2300 and 2340 3094552

Report No. 3094552 -H01 Pelican Products

FLASHLIGHT


PHOTO N0. 1


FLASHLIGHT

General - Photograph number one shows an overall view of the flashlight.


PHOTO N0. 1

1. Alkaline Batteries - [NOT SHOWN/NOT CALLED OUT] -(2 provided) -(Unlisted Component) - Manufacturer:Energizer; Manufacturer's Part Number: E91; Ratings: 1.5V, Alkaline AA, -18°C to +54°C

2. Enclosure - (Recognized Component) - Manufacturer: GE Plastics; Manufacturer's Part Number: EXL9330; Ratings: UL 94V-O, 140°C, Main Body minimum thickness 1.5mm, Dimensions: 6" L x %"diameter; Reference Illustrations 15-17

Alternate -(Recognized Component) - Manufacturer: GE Plastics; Manufacturer's Part Number: XENOY 5220U; Ratings: Flame Rating: HB, 75°C, Main Body minimum t.hickness 1 . 5mm, Dimensioos: 6" L x %"diameter Reference Illustrations 15-17

3 . Lens - [NOT CALLED OUT] -(Recognized Component) -Manufacturer: GE Plastics; Manufacturer's Part Number: (Lens and Top Cover) Lexan Resin 103R; Ratings: UL 94HB, 154°C, Overmolding on the top cover, RiMFiL 1627-01 polypropylene, Ratings: UL 94HB, 96°C, Reference Illustrations 4 and 5.

4. - [NOT SHOWN/ NOT CALLED OUT] - Embossed letters 0.020" raised on the surface of fiashlight, Reference markings page M 1


FLASHLIGHT

Issued: 09/01/06 Revised: N A

PHOTO N0.2


FLASHLIGHT

General - Photograph number two shows the internal parts of the flashlight.


PHOTO NO. 2

1 . Module - [NOT CALLED OUT] - (Unlisted Component) -Applcant's Drawing Number: 2303-353-000; Revision: H; Date: 08/11 /06, Reference Illustration 2.

2. Bulb (Unlisted Component) - Manufacturer: Pelican Products; Manufacturer's Part Number: 2304; Ratings: 3.0V, 0.470A maximum, Assembly consists of Bulb type 1 079 Carley, reflector: strippled aluminized surface, Reference lllustration2.

3 . Metal Parts - All metal parts are corrosion protected by either being stainless steel, brass, nickel or silver plated. Reference Illustration 1 and 2.


FLASHLIGHT

I

_ ___� _ :

. li®MityLite®230


MARKING NUMBER: 1


FLASHLIGHT

>: ;


ILLUSTRATION NUMBER: 1

R

Report No. 3094552 -H01 Pelican Products

FLASHLIGHT

543 2 1

P-EX-G:iS-02. P-EX96-01

O-EX94

P-EX'S4-03

KS-EX9+-0-2 0-3DXJB0!'.500( 4.5)H P 8:9-1-01 0-27X380�5QO(S)H K8-EX94 KS-EXG4-C1 K-£>194

.

II' l' I' I' I'

RET)IJNER 0,511K 8RAS PlAiE POS!TIYE i>lATE 1 0.5nt BRAS PLATE NEGATl>E SPRJNG 1 SPRING STEEL

NEGl!ThE SPRING 1 0.5 Tit( ElRAS Pl.ATE BASE 1 POM COMPRESS SPRING 1 MUSIC WIRE CONTACT PLATE 1 0..5ThltCOPPER PLATE

RETURN SPRlhJG 1 SP�ING STEL MD\IE GEAR 1 !'OM C<M:R 1 POM

PUSH GEAR 1 POU



NIC�lE PLATED

NICKI.£ PLATED NICl<LE PlATED

Sll'l/ER Pl.ATE[}

NICKI.£ PLATED

SILVER PLATED"' NJCKl.£ PlATE£i

:Wl$"tllS:�

\I :'( l SHEET 2 ol 2


FLASHLIGHT




FLASHLIGHT

:� I 2 .,

I � I 0 (l c; II ::!;;- ""!

,,

14

"

" ' Ji



l

Q G} v

' ' ,, ,,, '' , , ,,,,,, , , , '''"'' _,,,,,,,,, ·-- , .. ,,,,,,,,, __ , -···-·--- ----·--·----·------ ---

.·

1 0 0.970 Dll\

.090M!N.1110Mr\X -1

PRELIMINARY RELEASE ""��-��----�· ·--•�w-•-••·��··�-

PR l'RUDUCllC�I RELEASL 06 ·27-�4 NS\I A LEHI, HifYlllE ��JM 2M Vl1S .

0.02 R CONT -'- e "'0 D

.. '-. 1- l.079 ·'· EG I SIDE

DlA

SUPER DUPER MITYLITE 1H1·%B .C9Un'i11.11�':1x MrtD 00-12·97 X

MAX-Yn-.Tiol-:ilfm .42l.015, J&l lD .B4+.0i'-.Ol

+.02 1.130 TD l.i4l l?.OI RPV lD-12-L'l · .01 [ PlllYCl\liffilll!I[ lfW. VAS G[ U!Ali 611163

···r�·-HiifiliilVAsrr I \f ECil Oh·IYJ "'�'"� _, ___ �,-��--�,-.--��

0.02,

R CDt�T B p, CS

l

I

- "4" + 01"' u. c: .. , J

--0.84+.02 -.01

I o f-·· 1070

PLCS

4 DD NOT CHANGE �I ID CSA, FM 1" MSTIA' APPROVAL!"'''"""'""'"'"'""''"'._ .. .. , .. ,_ .... , ... !APPROVAL DRAWING

TllREAD l.0()2 X 18, .Ol FLATS. TO MA.TCH BODY, P/I� 2301 . . •· .•• . ... .. . · · .. . · . . . ? rJENERAI DRAFT ANG! I ON CORI 0.5 DUi UNLESS 2300 umnar

LITHLl�\1l[Sl. SPIClfl[Jl

1 G[l�ERAL Df<Af'T ANGL[ [JI� CAVITY LS DEG I SID[

0 IHEi<\JJSE Sl'[CfflED. �JO[[S:

,. e�IfJ, 1N . I�.�i MAT£RiAL• IJXi\N R �RW� "

,. CV• SilT H .E• 1"' 1 2303·920-100 F

,, � :c r G5 :c -I

r= r c: (/) -I �-I 5 z z c: ;; OJ m??OJ

"ti ;o<Tl <Tl =-c n o � ;+"ti z .. 0 o · a. "' c: 0 n "" fir � OJ

"' ±0 �

iirn ;o �<Tl c. < .. (i" 0 <Tl "" c. 0. . � z-l>g

VENi SEAL _____ _

2. fiD Nm rnANGE vnH1.1m rn, csA, MSHA, � UL APPRDVl!LNOTES: I. VDH PRESSURE: 3.0psiG

A i:346-62!H10 VAS 2346·620-000 VJ

REMOVED L£NS PIN 2303-920-100 2303-920-110 llAS 2271-92�-110 7-21-03 235:J-%H10 \ll!S 235�·96Hl0

..

SCAl,£:1

.., � ::c ' G'i ::c -I

;= ' c: en -I �-I 0 z z c: s ro m � "'

"D ;;o(I) CJ) =-on o§ ;:i. "Dz a P a."" c: Q g_ CD I/) !;';Rl:i:

Q �

ii I/) ;;o a; CJ) a.< ..(j"oCD CD a.a . . � z-)> a:

kE.VblOM5

SECTION A-ALTR DATE APPP:OVfTJ

PR RELEASE f'OR PRODUCTIOf\I 04 .. JS.04 T.T.

.110

. � ..... ...... .

.

E?r .460 .09 4

.430 .180 • · · ··· ..... ..... ........

A A

4 ... ·· ···· ···· . t

1.27 4

/�\, DO NOi CHA1'1GE WITHOUT FM, CSA, MSHA

MATERIAL: LEM:; OVERlv\OLDED WlfH

1.319 4 PLCS

fl![[

2270 & 2300 LENS OVER MOLD

DS

Cfil\":I'.

TOLER.•LICF5 PELICAN PRODUCTS, IN ULC;MAt Fcl'!t'i 23215 :EA.NlY AVE.,

"' ,,.: TORRAN(:E, CA 9Q.SQ5 -JI 1J'.) , /,\;i,,JfRl:.1 !ilif,t �'{;. -� �IOIES USE Cl.EAR LENS PART# 2303-920·100 A ''" I OF i "i-1llNE 2303 .. 920.110

"Tl � :c r Gi :c -I

F r c: en -I �-Ii5 z z c:s[J m � ..

"1l ;u "' "' =-c 0 0 § ;:i. "1l z � 0 o · c. "' c: 0 0 (/) -""' Ul 01

Rl ' :c 0 �

'i Ul ;u � "' c.< .. Fi"o "' (/) c. 0. . � z-)> �


PRODUCT EVALUATION OF UNLISTED COMPONENTS


Because unlisted components are uncontrolled, and they do not fall under a third party follow up program, INTERTEK ETL SEMKO may require these components to be tested and/or evaluated at least once annually, more often for certain components, as part of the independent certification process. The unlisted components in the table below require testing and/or evaluation as indicated.

Note to INTERTEK ETL SEMKO Follow Up Inspector:

Ship the samples to:

Sample Disposition:

The Component Evaluation Center, CEC, will notify you in writing when these components must be selected and sent to the CEC for re-evaluation

·

Component Evaluation Center

Due to the destructive nature of the testing, all samples will be discarded at the conclusion of testing unless, the manufacturer specifically requests the return of the samples. The request for return must accompany the initial component shipment.

The Unlisted Components covered by this report are shown in the following Table:


FLASHLIGHT

Photo Item Component

EVALUATION OF UNLISTED COMPONENTS

Send to CEC No. No. Description Manufacturer No. Frequency

. Qty or

1 1 Batteries NA NA Quarterly 1 NO 4 NA NA 1 NO

2 1 Module NA NA 1 NO 2 2 Bulb NA NA NO

* Quarterly, semi-annual, annual.

Visual Visual Visual Visual


Required Action

**note: Indicate any samples not available and provide the anticipated date that the component will be available.

*** Required Action (select one of the three): Visual Partial Full Evaluation


FLASHLIGHT REVISIONS

The following changes have been made to this Report:

NONE
