Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
BAYMAK is a BDR Thermea company and one of the leaders
of heating sector in Europe, has a proud tradition of
developing and producing boilers and heating systems to
the highest technological standards.
For 43 years BAYMAK has provided a wide range of cutting-
edge solutions, anticipating market evolutions and paying
attention to customer needs.
Anticipating market evolutions, Baymak has further
developed its range of products with a wide boilers'
offering and integrated solutions spoiling renewable
energies.
• Solar Systems: Forced draft installation with single or
double coil cylinders ( from 160 to 2000 litres ) and
natural draft with 100/160/200/300 lt. horizantal
solar tanks.
• Hot Water Storage Tanks: From 80 lt to 1000 lt. enamelled
steel single coil, double coil, combi type and buffer tanks.
• Biomass Boilers: From 17 kW to 40 kW with pellet, wood
log, chips, oilcake, wheat, corn.
• Gas/Oil Boilers: Wall-hung gas and floor-standing gas/oil
boilers, from 15 kW to 3460 kW.
1
Highest Quality Standards
Baymak has been very successful thanks to the attention
to its products quality.
In 1998 Baymak was awarded the ISO 9001 Certification
and in 2002 the ISO 9001:2000 Certification in
order to reach constantly the highest levels of quality.
As Baymak recognizes environment, health and safety
protection as strategic aims, nowadays dealing with
ISO 14000.
2
3
Integrated systemsBaymak has always been active in the development of solutions which ensure the maximum environmentalrespect. Baymak is also aware that future’s heating solutions are based on the integration betweenboilers and systems working with renewable energies.
Following this philosophy, Baymak has developed
the integrated solar system combining the
excellent technology of Baymak boilers with a
complete range of solar collectors and cylinders
for forced draft installation.
A concept of intelligent comfort which advantages
are low pollutant emissions (ecological comfort)
and high energy efficiency.
Principles Of Solar EnergyEvery object directly exposed to the sun absorb heat and increase its temperature. As a consequence of thechemical reactions that take place in the mass of the sun, a constant stream of energy is produced aselectromagnetical radiation.We define the “solar constant” as the amount of incoming solar electromagnetic radiation per unit area, measuredon the outer surface of Earth's atmosphere in a plane perpendicular to the rays.The solar constant includes all types of solar radiation (infrared rays, UV rays, etc.), not just the visible light. Itis measured to be roughly 1,366 watts per square meter (W/m2), though this fluctuates by about 6.9% duringa year (from 1,412 W/m2 in early January to 1,321 W/m2 in early July) due to the earth's varying distance fromthe Sun, and typically by much less than one part per thousand from day to day. The approximate average valuecited, 1,366 W/m2, is equivalent to 1.96 calories per minute per square centimeter, or 1.96 langleys (Ly) perminute.
As above stated, the Earth receives a total amount of radiation determined by its cross section but, as it rotates,
this energy is distributed across the entire surface area. Morevoer, at any given moment, the amount of Solar
radiation received at a location on the Earth's surface depends on the state of the atmosphere and the location's
latitude.
The Inclination Of Solar Collectors
The inclination of solar collectors is the angle between the plane of their surface and the horizontal surface they
rest on. To optimize collectors efficiency, the angle between collectors surface and incident rays should be 90°.
If collectors rest on a pitched roof it is advisable to keep the same inclination of the roof.
On the other hand, if they rest on a flat roof the following indications should be
considered when deciding the collector inclination:
• Summer 20 – 40°
• Winter 50 – 65°
• Middle seasons 40 – 60° Inclination angle between the
collectors and the horizontal plate
4
Percentage of energy
Wave lenght 0-0,38 um
7%UV rays
Energy 95 W/m2
Wave lenght 0.38-0.78 um
47%Visible
Energy 640 W/m2
Wave lenght 0.78- um
48%Infrared rays
Energy 618 W/m2
Average of the solar constant 1353 W/m2
Smart Comfort:The Forced Draft Baymak Solar Energy SystemThe circulation of the heat transfer fluid can be natural of forced. Natural circulation refers to the ability of afluid in a system to circulate continuously, with gravity and changes in heat energy (temperature) being the onlydriving force. Despite of installation simplicity, with natural circulation heat transfer fluid flows very slowly andthe amount of absorbed solar energy is very low. ����In case of forced circulation, heat transfer fluid is driven by means of a thermostat controlled pump. Flow ratecan be set to obtain the maximum solar energy absorption.
5
MODEL
TECHNICAL FEATURESGLASS
THICKNESS
SolarDuraSolar®P+ Sandy 4 mm 91.6 % 90.5 % Low iron temperedsandy solar glass
LIGHT TRANSM‹TTANCETd65
SOLAR ENERGYTRANSM‹TTANCE Tsol GLASS TYPE
• Collector GlassDurasolar ® P+ sandy glass is produced by Trakya Cam (fiiflecam), the biggest glass manufacturer of Turkey,
gives one of the highest performance among the other European glasses.
Durasolar ® P+ sandy glass that includes lower iron-oksit ratio, higher light transmittance and heat permeability
than the standard iron glass provides maximum efficiency for the collector performance.
Durasolar® P+ Temperred glass is resistant to physical outdoor factors as rain, UV, temperature, thermal shock,
stroke.
Durasolar® P+ glass has been tested by SPF Solartechnik Prüfung Forschung - Switzerland
Solar CollectorsA flat plate is the most common type of solar thermal collector, and is usually used to generate solar hot water.
A weatherproofed, rock wool insulated box containing a blue selective coated Cu or Alu metal absorber sheet
with built in pipes is placed in the path of sunlight.
Superior resistant with the thicknessof 1 mm aluminum back plate
Long life by strong patented frame
High thermal efficiency with tempered,low iron, �Sandy patterned glass
Minimum heat loss with insulation material of rock wool.
Leakproofed corner points surroundedwith a single piece of glass seal.
Manifold gasket with highlyheat resistant silicon
Highly selective coated absorber plate.
High heat transferred laserwelded riser pipes
• Collector AbsorberSelective coated T‹NOx copper or aluminium surface absorb the heat radiation to the plate in maximum level
and minimize the radiation heat loss.
The absorber has been tested in Germany/Fraunhofer-Institue.
The latest technology of selective coated absorbers that have been used for the Baymak new serie solar collectors
transfer the sun radiation heat in maximum level and minimize the reflection loss which decrease the efficiency.
Below the radiation heat losses for different coating materials are shown. As it is seen from the pictures the
minimum heat loss is supplied through the selective coated metal sheet.
6
Light spectrum
Quartz glassfilm
Titanium coating layer
Conjunctive layer
Metal plate
Heat transferred to plate
Radiation heat loss45%
5%Reflection
Paint coated
Transmitted heat
Radiation heat loss15%
5%Reflection
Black chromium
Transmitted heat Transmitted heat
5%5%Reflection
Radiation heat loss
Selective coated
• Absorber Coating for Baymak Solar CollectorsCollectors with selective coated absorbers are a clear alternative to conventional energy generation and also
help to considerably reduce CO2 emmissions.
As the heart of the solar collector, eta plus efficiently converts
solar energy into heat and at the same time protects the
collector against energy losses.
Provides optimal technical properties:
-�above-average aging and temperature resistance
-�outstanding homogeneity of the coating over the entire
material width-�absorption 95%, thermal emission 5%
-�top quality and a zero-emission industrial production process
Laser Welding TechnologyLASER welding methode which is the one of the most modern and latest technologies has been used to connect
the selective coated absorber surface to the riser pipes.
Baymak collectors produced by LASER welding methode protects the absorber and increase the aperture surface
between 2 % to 4 %.
7
Visible and shortwavelenght rays
Long wavelenght rays
Protector seraniccover layer againstto corrosion
Absorber layer
Corrosion protectionand cling surfaceMetal plate
Transmitted heat to the plate
Riser pipe profile
Absorber
Laser Welding
Riser pipe
Heat transfer in to the water
• Collector Harp SystemThanks to the 12 riser pipes the heat is transferred into the water
in maximum level and increases the efficiency of the collector.
• FrameThanks to the special design of the patented frame all the components have been held
together strongly.
The new frame protects the collector from all external factors over the years with
2 mm wall thickness.
• Glaze SealingThe new type of Baymak Collectors are protected by monobloc vulcanised EPDM sealing
that provides perfect leakness on the corners and maximum thermal durability against
UV rays.
• Manifold SealingManifold sealing has been made of silicon for perfect leakness and high temperature
durability.
• Collector InsulationFor new type of Baymak collectors, insulation material has been used as rookwool that is tested by SPF Institute.
This special rockwool includes the lowest level chemical binder.
• Collector Bottom PlateNew type BAYMAK collectors have more stronger and thicker new aluminium back
plate. The back plate thickness is 1mm. This plate provides maximum durability against
transportation problems, all weather conditions and all external factors.
8
MaximumInsulation
Heat insulation:40-50 kg/m2 densityLow Chemical Binder0.035 W/m2K ThermalConductivity
9
Baymak Solar CollectorsFor the forced draft installation Baymak has developed:• A wide range of solar collectors: gross surface between 2.51 m2 and 2.00 m2 built-in versions (IN models), selective coated copper or aluminium absorbers.• A wide range of enamelled cylinders: from 80 to 2. 000 litres with single coil / double coil/, enamelled buffertanks, combi tanks (tank in tank) and wall type cylinders (form 60 liter to 100 liter with 2kW electrical back up)Baymak solar thermal heating system uses the free energy from the sun to heat the domestic hot water( DHW ) and support for space heating.
ADVANCED XL ESSENTIAL XESSENTIAL BLACK X APOLLO S XESSENTIAL BLACK XL ESSENTIAL XL APOLLO S XLADVANCED X
TECHNICAL DATA ADVANCED XL ESSENTIAL BLACK XL ESSENTIAL X APOLLO S XLESSENTIAL XLADVANCED X ESSENTIAL BLACK X APOLLO S X
9150245
80.90%
1882 W
1773 W
1551 W
1322 W
2.51 m2
2.34 m2
2.34 m2
Aluminum
Mirotherm - Al
% 95
% 5
Black anodised Aluminum
2180 mm
1150 mm
80 mm
52 kg
low iron rate, temperred,
sandy patterned solar glass
4 mm
91.60%
90.50%
Vulkanized EPDM
Rockwool (40 mm)
0.8 mm Aluminum
12
10 mm
18 mm (3/4”)
Compression Joint
2.2 Liter
10 bar
15 bar
200 °C
180 °C
Solar Keymark/SRCC OG 100
9150205
76.80%
1427 W
1351 W
1190 W
1018 W
2.00 m2
1.87 m2
1.87 m2
Copper
SunSelect - Cu
% 95
% 5
Black anodised Aluminum
1750 mm
1150 mm
80 mm
42 kg
low iron rate, temperred,
sandy patterned solar glass
4 mm
91.60%
90.50%
Vulkanized EPDM
Rockwool (40 mm)
0.8 mm Aluminum
12
10 mm
18 mm (3/4”)
Compression Joint
1.71 Liter
10 bar
15 bar
200 °C
180 °C
Solar Keymark/SRCC OG 100
9150200
78.00%
1811 W
1703 W
1481 W
1253 W
2.51 m2
2.34 m2
2.34 m2
Copper
SunSelect - Cu
% 95
% 5
Black anodised Aluminum
2180 mm
1150 mm
80 mm
53 kg
low iron, temperred,
sandy patterned solar glass
4 mm
91.60%
90.50%
Vulkanized EPDM
Rockwool (40 mm)
0.8 mm Aluminum
12
10 mm
18 mm (3/4”)
Compression Joint
2.04 Liter
10 bar
15 bar
200 °C
180 °C
Solar Keymark/SRCC OG 100
9150243
80.50%
1493 W
1403 W
1219 W
1032 W
2.00 m2
1.87 m2
1.87 m2
Aluminum
Mirotherm - Al
% 95
% 5
Black anodised Aluminum
1750 mm
1150 mm
80 mm
42 kg
low iron rate, temperred,
sandy patterned solar glass
4 mm
91.60%
90.50%
Vulkanized EPDM
Rockwool (40 mm)
0.8 mm Aluminum
12
10 mm
18 mm (3/4”)
Compression Joint
1.8 Liter
10 bar
15 bar
200 °C
180 °C
Solar Keymark/SRCC OG 100
9150246
80.90%
1882 W
1773 W
1551 W
1322 W
2.51 m2
2.34 m2
2.34 m2
Aluminum
Mirotherm - Al
% 95
% 5
Pure Aluminum
2180 mm
1150 mm
80 mm
50 kg
low iron rate, temperred,
sandy patterned solar glass
4 mm
91.60%
90.50%
Vulkanized EPDM
Rockwool (40 mm)
0.8 mm Aluminum
12
10 mm
18 mm (3/4”)
Compression Joint
2.2 Liter
10 bar
15 bar
200 °C
180 °C
Solar Keymark/SRCC OG 100
9150244
80.50%
1493 W
1403 W
1219 W
1032 W
2.00 m2
1.87 m2
1.87 m2
Aluminum
Mirotherm - Al
% 95
% 5
Pure Aluminum
1750 mm
1150 mm
80 mm
42 kg
low iron rate, temperred,
sandy patterned solar glass
4 mm
91.60%
90.50%
Vulkanized EPDM
Rockwool (40 mm)
0.8 mm Aluminum
12
10 mm
18 mm (3/4”)
Compression Joint
1.8 Liter
10 bar
15 bar
200 °C
180 °C
Solar Keymark/SRCC OG 100
9150238
78.00%
1797 W
1695 W
1484 W
1262 W
2.51 m2
2.34 m2
2.34 m2
Aluminum
Mirotherm - Al
% 95
% 5
Pure Aluminum
2180 mm
1150 mm
80 mm
50 kg
low iron rate, temperred,
sandy patterned solar glass
4 mm
91.60%
90.50%
Vulkanized EPDM
Glasswool (40 mm)
0.8 mm Galvanizd Steel
10
10 mm
18 mm (3/4”)
Compression Joint
1.8 Liter
10 bar
15 bar
200 °C
180 °C
Solar Keymark
9150237
77.00%
1419 W
1338 W
1166 W
984 W
2.00 m2
1.87 m2
1.87 m2
Aluminum
Mirotherm - Al
% 95
% 5
Pure Aluminum
1750 mm
1150 mm
80 mm
40 kg
low iron rate, temperred,
sandy patterned solar glass
4 mm
91.60%
90.50%
Vulkanized EPDM
Glasswool (40 mm)
0.8 mm Galvanized Steel
10
10 mm
18 mm (3/4”)
Compression Joint
1.5 Liter
10 bar
15 bar
200 °C
180 °C
Solar Keymark
Product Code
Efficiency
Power Output per collector at 1000W/sqm
Peak Power
Delta T: 10 K
Delta T: 30 K
Delta T: 50 K
Brut Size
Aperute Area
Absorber Area
Absorber
Type
Coating
Absorpion
Emission
Frame
Height
Width
Depth
Weight
Glass
Type
Thickness
Light of Transmittance Td65
Solar Energy Transmittance Tsol
Other features
Sealing
Insulation
Black Plate
Number of Risers
Ø Risers
Ø Manifold (Header)
Connections
Water Volume
Max.Working Pressure
Testing Pressure
Max.Temperature
Stagnation Temperature
Certification
Technical Data ADVANCED XL915020078.00%
1811 W1703 W1481 W1253 W2.51 m2
2.34 m2
2.34 m2
CopperSunSelect - Cu
% 95% 5
Black anodised Aluminum2180 mm1150 mm80 mm53 kg
low iron, temperred, sandy patterned solar glass4 mm
91.60%90.50%
Vulkanized EPDMRockwool (40 mm)0.8 mm Aluminum
1210 mm
18 mm (3/4”)Compression Joint
2.04 Liter10 bar15 bar
200 °C180 °C
Solar Keymark/SRCC OG 100
Product CodeEfficiencyPower Output per collector at 1000W/sqmPeak PowerDelta T: 10 KDelta T: 30 KDelta T: 50 KBrut SizeAperute AreaAbsorber AreaAbsorberTypeCoatingAbsorpionEmissionFrameHeightWidthDepthWeightGlassTypeThicknessLight of Transmittance Td65Solar Energy Transmittance TsolOther FeaturesSealingInsulationBlack PlateNumber of RisersØ RisersØ Manifold (Header)ConnectionsWater VolumeMax.Working PressureTesting PressureMax.TemperatureStagnation TemperatureCertification
Baymak Solar Collector ModelsAdvanced XLThe Advanced XL vertical flat-plate collector has a copper absorber with a high efficiency selective coating.Vertical copper pipes are laser welded to the absorber. The collector brut area of 2,51 m2 is available for bothforced and natural circulation systems. Advanced XL collector frame material made from black anodisedaluminium.
• 2,51 m2 gross area• Copper selective surface• Black anodised aluminium frame
Advanced XThe Advanced X vertical flat-plate collector has a copper absorber with a high efficiency selective coating. Verticalcopper pipes are laser welded to the absorber. The collector brut area of 2,00 m2 is available for both forcedand natural circulation systems. Advanced X collector frame material made from black anodised aluminium.
• 2,0 m2 gross area• Copper selective surface• Black anodised aluminium frame
10
Technical Data ADVANCED X915020576.80%
1427 W1351 W1190 W1018 W
2.00 m2
1.87 m2
1.87 m2
CopperSunSelect - Cu
% 95% 5
Black anodised Aluminum1750 mm1150 mm80 mm42 kg
low iron rate, temperred, sandy patterned solar glass4 mm
91.60%90.50%
Vulkanized EPDMRockwool (40 mm)0.8 mm Aluminum
1210 mm
18 mm (3/4”)Compression Joint
1.71 Liter10 bar15 bar
200 °C180 °C
Solar Keymark/SRCC OG 100
Product CodeEfficiencyPower Output per collector at 1000W/sqmPeak PowerDelta T: 10 KDelta T: 30 KDelta T: 50 KBrut SizeAperute AreaAbsorber AreaAbsorberTypeCoatingAbsorpionEmissionFrameHeightWidthDepthWeightGlassTypeThicknessLight of Transmittance Td65Solar Energy Transmittance TsolOther FeaturesSealingInsulationBlack PlateNumber of RisersØ RisersØ Manifold (Header)ConnectionsWater VolumeMax.Working PressureTesting PressureMax.TemperatureStagnation TemperatureCertification
Essential Black XLThe Essential Black XL vertical flat-plate collector has an aluminium absorber with a high efficiency selectivecoating. Vertical copper pipes are laser welded to the absorber. The collector brut area of 2,51 m2 is availablefor both forced and natural circulation systems. Essential Black XL collector frame material made from blackanodised aluminium.
• 2,51 m2 gross area• Aluminium selective surface• Black anodised aluminium frame
Essential Black XThe Essential Black X vertical flat-plate collector has an aluminium absorber with a high efficiency selectivecoating. Vertical copper pipes are laser welded to the absorber. The collector brut area of 2,0 m2 is availablefor both forced and natural circulation systems. Essential Black X collector frame material made from blackanodised aluminium.
• 2,0 m2 gross area• Aluminium Selective Surface• Black Anodised Aluminium frame
11
Technical Data ESSENTIAL BLACK XL915024580.90%
1882 W1773 W1551 W1322 W2.51 m2
2.34 m2
2.34 m2
AluminumMirotherm - Al
% 95% 5
Black anodised Aluminum2180 mm1150 mm80 mm52 kg
low iron rate, temperred, sandy patterned solar glass4 mm
91.60%90.50%
Vulkanized EPDMRockwool (40 mm)0.8 mm Aluminum
1210 mm
18 mm (3/4”)Compression Joint
2.2 Liter10 bar15 bar
200 °C180 °C
Solar Keymark/SRCC OG 100
Product CodeEfficiencyPower Output per collector at 1000W/sqmPeak PowerDelta T: 10 KDelta T: 30 KDelta T: 50 KBrut SizeAperute AreaAbsorber AreaAbsorberTypeCoatingAbsorpionEmissionFrameHeightWidthDepthWeightGlassTypeThicknessLight of Transmittance Td65Solar Energy Transmittance TsolOther FeaturesSealingInsulationBlack PlateNumber of RisersØ RisersØ Manifold (Header)ConnectionsWater VolumeMax.Working PressureTesting PressureMax.TemperatureStagnation TemperatureCertification
Technical Data ESSENTIAL BLACK X915024380.50%
1493 W1403 W1219 W1032 W2.00 m2
1.87 m2
1.87 m2
AluminumMirotherm - Al
% 95% 5
Black anodised Aluminum1750 mm1150 mm80 mm42 kg
low iron rate, temperred, sandy patterned solar glass4 mm
91.60%90.50%
Vulkanized EPDMRockwool (40 mm)0.8 mm Aluminum
1210 mm
18 mm (3/4”)Compression Joint
1.8 Liter10 bar15 bar
200 °C180 °C
Solar Keymark/SRCC OG 100
Product CodeEfficiencyPower Output per collector at 1000W/sqmPeak PowerDelta T: 10 KDelta T: 30 KDelta T:50 KBrut SizeAperute AreaAbsorber AreaAbsorberTypeCoatingAbsorpionEmissionFrameHeightWidthDepthWeightGlassTypeThicknessLight of Transmittance Td65Solar Energy Transmittance TsolOther FeaturesSealingInsulationBlack PlateNumber of RisersØ RisersØ Manifold (Header)ConnectionsWater VolumeMax.Working PressureTesting PressureMax.TemperatureStagnation TemperatureCertification
Essential XLThe Essential XL vertical flat-plate collector has an aluminium absorber with a high efficiency selective coating.Vertical copper pipes are laser welded to the absorber. The collector brut area of 2,51 m2 is available for bothforced and natural circulation systems. Essential XL collector frame material made from pure (grey) aluminium.
• 2,51 m2 gross area• Aluminium selective surface• Pure (Grey) aluminium frame
Essential XThe Essential X vertical flat-plate collector has an aluminium absorber with a high efficiency selective coating.Vertical copper pipes are laser welded to the absorber. The collector brut area of 2,00 m2 is available for bothforced and natural circulation systems. Essential X collector frame material made from pure (grey) aluminium.
• 2,00 m2 gross area• Aluminium selective surface• Pure (Grey) aluminium frame
12
Technical Data ESSENTIAL XL915024680.90%
1882 W1773 W1551 W1322 W2.51 m2
2.34 m2
2.34 m2
AluminumMirotherm - Al
% 95% 5
Pure Aluminum2180 mm1150 mm80 mm50 kg
low iron rate, temperred, sandy patterned solar glass4 mm
91.60%90.50%
Vulkanized EPDMRockwool (40 mm)0.8 mm Aluminum
1210 mm
18 mm (3/4”)Compression Joint
2.2 Liter10 bar15 bar
200 °C180 °C
Solar Keymark/SRCC OG 100
Product CodeEfficiencyPower Output per collector at 1000W/sqmPeak PowerDelta T: 10 KDelta T: 30 KDelta T: 50 KBrut SizeAperute AreaAbsorber AreaAbsorberTypeCoatingAbsorpionEmissionFrameHeightWidthDepthWeightGlassTypeThicknessLight of Transmittance Td65Solar Energy Transmittance TsolOther FeaturesSealingInsulationBlack PlateNumber of RisersØ RisersØ Manifold (Header)ConnectionsWater VolumeMax.Working PressureTesting PressureMax.TemperatureStagnation TemperatureCertification
Technical Data ESSENTIAL X915024480.50%
1493 W1403 W1219 W1032 W2.00 m2
1.87 m2
1.87 m2
AluminumMirotherm - Al
% 95% 5
Pure Aluminum1750 mm1150 mm80 mm42 kg
low iron rate, temperred, sandy patterned solar glass4 mm
91.60%90.50%
Vulkanized EPDMRockwool (40 mm)0.8 mm Aluminum
1210 mm
18 mm (3/4”)Compression Joint
1.8 Liter10 bar15 bar
200 °C180 °C
Solar Keymark/SRCC OG 100
Product CodeEfficiencyPower Output per collector at 1000W/sqmPeak PowerDelta T: 10 KDelta T: 30 KDelta T: 50 KBrut SizeAperute AreaAbsorber AreaAbsorberTypeCoatingAbsorpionEmissionFrameHeightWidthDepthWeightGlassTypeThicknessLight of Transmittance Td65Solar Energy Transmittance TsolOther FeaturesSealingInsulationBlack PlateNumber of RisersØ RisersØ Manifold (Header)ConnectionsWater VolumeMax.Working PressureTesting PressureMax.TemperatureStagnation TemperatureCertification
Apollo S XLThe Apollo S XL vertical flat-plate collector has an aluminium absorber with a high efficiency selective coating.Vertical copper pipes are laser welded to the absorber. The collector brut area of 2,51 m2 is available for bothforced and natural circulation systems. Apollo S XL collector frame material made from pure (grey) aluminium.
• 2,51 m2 gross area• Aluminium selective surface• Pure (Grey) aluminium frame
Apollo S XThe Apollo S X vertical flat-plate collector has an aluminium absorber with a high efficiency selective coating.Vertical copper pipes are laser welded to the absorber. The collector brut area of 2,00 m2 is available for bothforced and natural circulation systems. Apollo S X collector frame material made from pure (grey) aluminium.
• 2,00 m2 gross area• Aluminium selective surface• Pure (Grey) aluminium frame
12
Technical Data APOLLO S XL915023878.00%
1797 W1695 W1484 W1262 W2.51 m22.34 m22.34 m2
AluminumMirotherm - Al
% 95% 5
Pure Aluminum2180 mm1150 mm80 mm50 kg
low iron rate, temperred, sandy patterned solar glass4 mm
91.60%90.50%
Vulkanized EPDMGlasswool (40 mm)
0.8 mm Galvanizd Steel10
10 mm18 mm (3/4”)
Compression Joint1.8 Liter10 bar15 bar
200 °C180 °C
Solar Keymark
Product CodeEfficiencyPower Output per collector at 1000W/sqmPeak PowerDelta T: 10 KDelta T: 30 KDelta T: 50 KBrut SizeAperute AreaAbsorber AreaAbsorberTypeCoatingAbsorpionEmissionFrameHeightWidthDepthWeightGlassTypeThicknessLight of Transmittance Td65Solar Energy Transmittance TsolOther FeaturesSealingInsulationBlack PlateNumber of RisersØ RisersØ Manifold (Header)ConnectionsWater VolumeMax.Working PressureTesting PressureMax.TemperatureStagnation TemperatureCertification
Technical Data APOLLO S X915023777.00%
1419 W1338 W1166 W984 W
2.00 m21.87 m21.87 m2
AluminumMirotherm - Al
% 95% 5
Pure Aluminum1750 mm1150 mm80 mm40 kg
low iron rate, temperred, sandy patterned solar glass4 mm
91.60%90.50%
Vulkanized EPDMGlasswool (40 mm)
0.8 mm Galvanized Steel10
10 mm18 mm (3/4”)
Compression Joint1.5 Liter10 bar15 bar
200 °C180 °C
Solar Keymark
Product CodeEfficiencyPower Output per collector at 1000W/sqmPeak PowerDelta T: 10 KDelta T: 30 KDelta T: 50 KBrut SizeAperute AreaAbsorber AreaAbsorberTypeCoatingAbsorpionEmissionFrameHeightWidthDepthWeightGlassTypeThicknessLight of Transmittance Td65Solar Energy Transmittance TsolOther FeaturesSealingInsulationBlack PlateNumber of RisersØ RisersØ Manifold (Header)ConnectionsWater VolumeMax.Working PressureTesting PressureMax.TemperatureStagnation TemperatureCertification
Power output of a solar system is not particularly high in comparison with standard heating systems. For example,
a 5 m2 solar system can reach a maximum power of 2,5 kW while working under most favourable conditions.
Thus, the storage tanks is one of the most important components of the system since the sun gives his maximum
contribution only for few hours per day and not every day.
We can roughly state the tank capacity has to be 1,5-2 times the daily DHW demand. By increasing its capacity
it would be possible to store a bigger amount of energy but inner temperature level would inevitably decrease
(that means the auxiliary boiler has to switch on much more frequently).
Baymak Solar Storage Tanks
Generally, 200-400 litres double coil storage tanks are the best choice for single houses and apartments. Solar
circuit is connected to lower coil and auxiliary boiler to upper coil. The density difference between hot and cold
water inside the tank causes temperatures stratification. Being lighter, hot water collects in the upper part of
the storage tank, whereas cold water collects in the bottom. The bigger is the ratio between height and diameter,
the more the temperatures stratify.
Thus, the lower is the bottom temperature, the more profitably the solar system will operate even in case of
scarce solar irradiation.
The storage tank insulation must be very well insulated. Thermal losses amount should be as low as possible.
For example, the difference in terms of energy waste between an insulation coefficient of 3 W/°C (normal tank)
and an insulation coefficient of 1,5 W/°C (standard solar tank) is roughly 450 kWh.
In case of hard water, it’s advisable to keep the storage temperature lower than 60°C to avoid scale deposits
and coils efficiency decrease as a consequence (a 2 mm deposit corresponds to an efficiency decrease of 20%,
a 5 mm deposit to a decrease of 40%). Still regarding this matter, also the delta between inlet and delivery
temperatures of the coil should not be higher than 15°C.
DHW
To the boiler
Cold water
Solar Exchanger
To the collector
Solar Volume
Integration Volume
Exchanger
13
Baymak Storage Tank With Single Coil
Maximum working pressure : 8 bar
Maximum testing pressure : 12 bar
Maximum temperature: 85 C
Insulation: CFC free PU (polyurethane)
Optional: heating element from 2 kw until 12 kw
SERVICE DOORTHERMOMETER
CIRCUIT OUTLET 1” MALE OR FEMALE
SERVICE CIRCULATION OUTLETR 3/4” MALE OR FEMALE
SERPENTINE INLETR 1” FEMALE
SENSOR PLACE
SERPENTINE OUTLETR 1” FEMALECIRCUIT INLET R 1” MALE OR FEMALE
14
Height
Diameter
Circuit inlet
Serpentine outlet
Sensor case
Serpentine inlet
Service circulation
Hot water outlet
The height of cleaning door
Cleaning door
Serpentine inlet / outlet diameter
Circuit inlet / diameter of hot water outlet
Diameter of service circulation
Weight
Description
mm
mm
mm
mm
mm
mm
mm
mm
mm
inch
inch
inch
kg
STORAGE TANK WITH SINGLE COILCAPASITY
80S900
500
70
220
355
505
635
790
-
-
1”
1”
3/4”
38
100S105
500
70
220
400
550
790
945
-
-
1”
1”
3/4”
43
120S930
600
80
240
420
505
595
750
-
-
1”
1”
3/4”
54
160S1270
600
80
240
375
600
785
1050
-
-
1”
1”
3/4”
81
180S1210
615
80
245
350
460
510
1120
***
***
1''
1''
3/4''
90
200S1300
600
80
240
515
650
935
1210
-
-
1”
1”
3/4”
90
300S1210
740
85
280
555
685
870
1135
320
DN 100
1”
1”
3/4”
109
400S1560
740
85
280
605
780
1225
1490
320
DN 100
1”
1”
3/4”
178
500S1860
740
85
280
650
875
1525
1785
320
DN 100
1”
1”
3/4”
202
800S1700
1050
120
350
815
1040
1285
1625
505
DN 250
1”
1”
3/4”
261
1000S2050
1050
125
350
1060
1280
1635
1975
505
DN 250
1”
1”
3/4”
295
1810
615
80
240
405
935
1260
1720
***
***
1''
1''
3/4''
105
300SLDimensions
A
B
C
D
E
F
G
H
L
M
N
O
P
U
Solar pump group
3 Fixing material
4 Baymak expansion tank
5 Baymak storage tank
2
1 Baymak solar collectors
6 Control panel
Insulation material:Polyurethane, densitiy: 40 kg/m3Thickness: 50 mmThe models 800 lt and 1000 is with 100mm soft foam
Enamelled tank
Enamelled coil
Mg anode
Flange
Cover in any colour
4
4
4
4
4
4
Range: 80 - 200 Lt.
SOR M
5
1
2
4
36
Range: 300 -1000 Lt.
Baymak Storage Tank With Double Coil
Maximum working pressure : 8 bar
Maximum testing pressure : 12 bar
Maximum temperature: 85 C
Insulation: CFC free PU (polyurethane)
Optional: heating element from 2 kw until 12 kw
SERVICE DOOR
HOT WATER OUTLETR 1” MALE OR FEMALE
SERPENTINE INLET R 1” FEMALE
CIRCUIT INLET R 1”MALE OR FEMALE
SERPENTINE OUTLET R 1” FEMALE
SERVICE CIRCULATION OUTLETR 3/4” MALE OR FEMALE
SERPENTINE OUTLET R 1” FEMALESERPENTINE INLET R 1” FEMALE
SENSOR PLACE
SERPENTINE PLACE
HeightDiameterCircuit inletSerpentine outletSensor caseSerpentine inletService circulationhot water outletSerpentine outletSensor caseSerpentine inletThe height of cleaning doorCleaning doorSerpentine inlet / outlet diameterCircuit inlet / Hot water outlet diameterService circulation diameterWeight
Description
mmmmmmmmmmmmmmmmmmmmmmmm
inchinchinchkg
STORAGE TANK WITH DOUBLE COILCAPASITY
80D-----------------
100D-----------------
120D-----------------
160D127060080
2403706007851060700785870******1”1”
3/4”86
180D121061580
2453504605101120555650815******1''1''
3/4''98
200D130060080
24051565093512107408901020******1”1”
3/4”98
300D121074085
2805556858701135785875950320
DN 1001”1”
3/4”116
400D156074085
2806057801225149097511551310320
DN 1001”1”
3/4”190
500D186074085
28065087515251785118014051610320
DN 1001”1”
3/4”218
800D17001050120350815
104012851625119512851420505
DN 2501”1”
3/4”276
1000D205010501203521060128016351975143516351760505
DN 2501”1”
3/4”308
181061580
24040593512601720103512601485********
1''1''
3/4''119
300DLDimensions
ABCDEFGHIJKLMNOPU
15
5
1
2
4
3
Range: 160 - 200 Lt.
Range: 300 - 1000 Lt.
Insulation material:Polyurethane, densitiy: 40 kg/m3Thickness: 50 mmThe models 800 lt and 1000 is with 100mm soft foam
Enamelled tank
Enamelled coil
Mg anode
Flange
Cover in any colour
4
4
4
4
4
4
6
3 Fixing material
4 Baymak expansion tank
5 Baymak storage tank
2
1 Baymak solar collectors
6 Control panel
SOR M
Baymak Combi Storage Tank (Tank in Tank)
Height
Diameter (including insulation)
Boiler return
Serpentine outlet
Sensor case
Serpentine inlet
Boiler inlet
Hot water inlet
The height of cleaning door
Cleaning door
Serpentine inlet / outlet diameter
Hot water inlet / Diameter of boiler return pipe
Diameter of boiler inlet pipe
Volume of hot water
Volume of heating water
Weight
Combi circuit inlet
Combi hot water outlet
Combi sensor case
Combi circuit inlet / Diameter of hot water outlet
H800/160L H1000/200L
mm
mm
mm
mm
mm
mm
mm
mm
mm
inch
inch
inch
lt
lt
kg
mm
mm
mm
inc
2065
1050
125
350
1035
1250
1525
1890
505
DN 250
1”
1”
3/4”
160
640
565
2065
2065
2065
1/2”
2125
1050
190
420
1110
1345
1610
1985
505
DN 250
1”
1”
3/4”
200
800
620
2120
2120
2120
1/2”
COMBI STORAGE TANKCAPASITY
A
B
C
D
E
F
G
H
L
M
N
O
P
R
S
U
V
Y
Z
Q
DescriptionDimensions
16
HOT WATER OUTLETR 1” MALE OR FEMALE
SERVICE CIRCULATIONOUTLET R 3/4” MALE OR FEMALE
SERPENTINE INLETR 1” FEMALE
SERPENTINE OUTLETR 1” FEMALE
CIRCUIT INLETR 1” MALE OR FEMALE
B
O
P
N
A H G F E
DC
M
L
Accessories For Forced Draft Installation
Features:• Intuitive, menu-conducted operation with graphic symbols and four operating keys.
• 6 sensors that can be linked
• 3 programmable exits (230V / 1A)
• Thermostat function
• 3 levels hourly programming on daily basis
• Regulator of the energy output ( flow regulator as optional accessory)
• Display of the istantaneous temperatures of the collector and of the cylinder
• Temperature differential regulation digitally adjustable regulation values
• Rotation speed control or switch control of solar circulation pump.
• Special function for systems with tube collectors
• Integrated operating hour meter for storage tank charging
• Extensive functions for system monitoring with error and failure display through symbols
• Integrated energy productivity measurement which by means of the productivity measuring set (accessories)
measures the energy obtained by a solar system.
• Storing of all adjusted values even in the case of any longer mains voltage breakdown.
• Various protective functions, as e.g. system protection, collector protection, recooling and antifreezing
The differential controller “SOR-M PLUS” used in the integrated solar system Baymak, is distinguished by the
easiness of use thanks to a simple display with only 4 buttons, of the system’s working.
The “SOR-M PLUS” controller grants a perfect regulation of solar systems installation made also by 2 tanks of
collectors or 2 storage tanks. It can be used also on a traditional solar installation, as well as shown on the 4
different installation schemes. (Described in the next page).
The solar automatic controller SOR M regulates thermal solar systems with up to 2 collectors or 2 storage tank
and may be used for five system types.
“SOR-M PLUS” Controller
The perfect functioning of the system can be obtained through the optimization of the flows of each circuit,
reaching the right room temperature as well as measuring the spoiled energy.
This goal can be reached through simple and advanced controllers, which receive signals from various elements
and allow to set the control temperature, the timings for switching on auxiliary boilers, etc.
The controllers transform the reading of the temperature into an electric signal that switch on/off a specific
process. The controller allows the fluid to get into circulation only with a real solar energy power support; it
measures the temperature out of the collector and in the bottom of the tank through sensors. The differential
thermostat compares both temperatures so that, in case the temperature is higher than the set limit, the
circulating pump starts working. Apart from what explained above, the controller can be adopted in different
points and for many uses inside these types of installation.
• Controllers
17
SOR M
Installation Schemes (With “SOR-M PLUS” Controller)
Electric Schemes“SOR-M PLUS” controller
“Eco” controller
Voltage network side Low voltage side
Voltage network side Low voltage side
Collector
Collector sensor
Cylinder 1
Upp
er c
oil s
enso
r
Low
er c
oil s
enso
r
Cylinder 2
Solar pump 1 Solar pump 2
Flow meter
Return sensor
Calorimeter
Collector sensorCollector sensor
Collector 1
Cylinder 1
Upp
er c
oil s
enso
r
Low
er c
oil s
enso
r
Return sensor
Flow meter
Collector 2
Solar pump
Calorimeter
CollectorCollector sensor
Cylinder 1
Upp
er c
oil s
enso
r
Low
er c
oil s
enso
r
Cylinder 2
Flow meter
Return sensor
Calorimeter
Low
er c
oil s
enso
r
Solar pump
Collector sensorCollector sensor
Collector 1
Cylinder 1
Upp
er c
oil s
enso
r
Low
er c
oil s
enso
r
Return sensor
Flow meter
Collector 2
Solar pump 1
Calorimeter
Solar pump 2
PE Discharge wire on the ground floor WMM Flow transducer
L Phase-network T1 Thermal sensor of the collector 1
N Neutral wire-network T2 Thermal sensor of the storagetank 1
A1 Phase-Rele 1 T3 Thermal sensor of the collector 2/storage tank 2
N Neutral wire-network-Rele 1 T4 Thermal sensor of the collector-return
A2 Phase-Rele 2 T5 Thermal sensor of the heatingcircuit/cooling or differentialtemperature* regulator source
N Neutral wire-Rele 2 T6 Thermal sensor of the anti-frost*orof the well differential temperatureregulator or general measuringpoint (it is masked when it is notconnected)
A3 Phase-Rele 3 * Freely programmable sensor T1..T6
N Neutral wire-Rele 3
PE Discharge wire on the ground floor WMM Calorimeter (not present)
L Phase-network T1 Thermal sensor of the collector
N Neutral wire-network T2 Thermal sensor of the storage tank
A1 Phase-Rele 1 T3 Thermal sensor of the collector
N Neutral wire-network-Rele 1 T4 Thermal sensor of the collector-return
A2 Phase-Rele 2
N Neutral wire-Rele 2
18
“SOR S” ControllerThe differential controller “SOR S” used in the integrated solar system Baymak, is distinguished by the easiness
of use, thanks to a simple display with only 4 buttons, of the system’s working. The solar automatic controler
Sor S regulates thermal solar systems with one collector and one storage tank.
Features:• Intuitive, menu-conducted operation with graphic symbols and four operating keys.
• 3 sensors that can be linked
• 3 programmable exits (230V / 1A)
• Thermostat function
• 3 levels hourly programming on daily basis
• Regulator of the energy output ( flow regulator as optional accessory)
• Protection of the collector against over temperatures
• Temperature differential regulation digitally adjustable regulation values
• Rotation speed control or switch control of solar circulation pump.
• Special function for systems with tube collectors
• Integrated operating hour meter for storage tank charging
• Extensive functions for system monitoring with error and failure display through symbols
• Baymak Solar StationBaymak solar station, is provided with thermal
insulation, includes in compact dimensions
all the components for a correct working of
the system and the greatest
reliability.
Baymak solar kit has been developed to be
connected to the range of instantaneous gas
boilers. It represents a compact solution which
includes adjustable thermostatic mixing valve
and diverter valve. If the temperature of the
water warmed by the solar system does not
reach the desired level of comfort, the diverter
valve makes the boiler to intervene to supply
DHW at the desired temperature.
• Flow� rate: 4 - 16 lt min.• High system efficiency• All components in one body• Ready for installing• High quality components• With Solar pump• Body with Insulation• Expansion tank connection part• with Safety Valve� and air valve installed�• Easy mounting and maintenance• Maxiumum working temperature 160 C• Maximum short term starting temperature• Maximum working pressure• Grundfos type: 15 - 16 solar pump• Maximum pump head :• Maximum pump flow : �
19
Installation of an expansion vessel with a high temperature resistant membrane is recommended for solar
systems. Their function is to absorb the expansion of the heat transfer fluid as the temperature increases in the
primary circuit, to maintain pressure inside the circuit within the allowable pressure range and to prevent the
introduction of air into the circuit during system cooldown.
20
Fernox Solar S1 is a clear, orange liquid with a distinct, faint odour. It has been specifically formulated for use
as a heat transfer fluid within solar thermal heating systems at elevated temperatures.
Fernox Solar S1 employs volatile corrosion inhibitors that will protect the installation when the heat transfer fluid
is in either a gaseous or liquid state at temperatures in excess of 180°C.
Solar Liquid For Solar Installation
Baymak Expansion Vessel For Solar Installation
• Suitable for solar energy systems
• Electrostatic powder paint
• CE Certification
• Optimal working temperature 0-110 °CCodes
17100018 TM 7,5 LT
17100015 TM 18 LT
17100017 TM 25 LT
17100012 TM 40 LT
17100002 TM 50 LT
17100003 TM 80 LT
17100004 TM 100 LT
17100005 TM 200 LT
17100006 TM 300 LT
17100007 TM 500 LT
17100008 TM 750 LT
17100009 TM 1000 LT
Capacity
• An inhibited heat transfer fluid for all solar thermal applications
• Frost protection to minus 28°C
• Volatile corrosion inhibitor for protection in gas and liquid phases
• Stable pH across the range of operational temperatures
• Compatible with all models of solar panels
21
Hydraulic Assembly Accessories For Solar Thermal Installations
Elbow18x3/4”
Blind Plug18x18 Nipple
Elbow18x3/4”
BlindPlug
Manual Air Bleed 1/2”
Automatic Air Bleed 1/2”
PHOTOS DESCRIPTION CODES
63 0644 0014
63 610 3049
09140074
09140075
63 1124 3001
63 1124 3002
Sensor Hive With
Manuel Air Bleed Ø18 mm
Sensor Hive With
Automatic Air Bleed Ø18 mm
Flex Hose (U Type)
HMF-05/09-011/16-HB-‹ZL-L400
Flex Hose (Straight Type)
HMF-05/09-011/16-3/4N-HB-‹ZL-L160
L: 241 mm
Ø18 mm x Ø18 mm Nipple
Ø18 mm x 3/4” Elbow
Ø18 mm x Blind Plug
Ø18 mm x 3/4” Nipple
Hive Ø18 mm
Complete Sensor Hive L:144 mm
PHOTOS DESCRIPTION CODES
63 0644 0016
63 0644 0017
63 0644 0018
63 0644 0015
63 0644 0021
63 1032 3010
22
Hydraulic Assembly Kits For Solar Thermal Installations
4 or 5
4 or 5 4 or 5
3/4”Blind plug
13
2
1
2
6 1
3 4
1 16
3
1 2 3 4 5
1 7 6 1
1 7 6 12 3
4 or 5
1 2
13
21
3
3
7
7
4 or 5
13
2 31
1 2
Codes
1 K CollectorBase Kit
2 K CollectorBase Kit
1 K Collector KitWith Manuel AirVent and Sensor
Plug
2 K Collector KitWith Manuel AirVent and Sensor
Plug
1 K Collector KitWith Automatic
Air Vent andSensor Plug
2 K Collector KitWith Automatic
Air Vent andSensor Plug
Photos 09140080 09140081 09140082 09140084 0914008509140083
63 0644 0016
63 0644 0017
63 0644 0018
09140074
09140075
62 1124 3001
63 1124 3002
Ø18 mm x Ø18 mm Nipple
Ø18 mm x 3/4” elbow
Ø18 mm x blind plug
sensor hive with manuel air
bleed Ø18 mm
sensor hive with automatic air
bleed Ø18 mm
-
2 pcs
2 pcs
-
-
-
-
2 pcs
2 pcs
2 pcs
-
-
-
-
-
1 pc
2 pcs
1 pc
-
-
-
2 pcs
1 pc
2 pcs
1 pc
-
-
-
-
1 pc
2 pcs
-
1 pc
-
-
2 pcs
1 pc
2 pcs
-
1 pc
-
-
1
2
3
4
5
6
7
No Description
Flex Hose (U Type)
HMF-05/09-011/16-HB-‹ZL-L400
Flex Hose (Straight Type)HMF-05/09-011/16-3/4N-HB-‹ZL-L160L: 241 mm
23
Roof Mounting Kits
IMPORTANT = * / ** This Roof Anchors ( Rafter Fixings ) has to be checked by installers before ordering because of the different tiles.
A ( 0,30 : 1 )8
6
10
4
A
A ( 1 : 3 )
A ( 1 : 2 )
CodePicture
09140070 09140071 09140072 09140076 0914007909140073
9140088
63 1024 0255
63 1024 0248
63 1024 0247
63 1050 0098
63 1050 0112
63 1050 0113
63 1050 0114
63 1050 0120
63 1050 0120
63 1050 0115
63 1050 0126
63 1024.2417
63 1050 0099
63 1050 0108
63 1050 0100
63 1050 0109
63 0541 0005
05 9921 0031
05 9930 0095
05 9912 0114
05 9912 0112
Arrangable roofconnection bracket for wind
and snow loads.
Description Colour
09140077 09140078
1 K AL SolarPanel Roof Kit
“Z” Profile-Silver
316 LStainless
steel
1 K AL SolarPanel Kit “Z”Profile-Black
1 K AL SolarPanel Roof Kit
“L” Profile-Black
2 K AL SolarPanel Roof Kit
“Z” Profile-Silver
2 K AL SolarPanel Kit “Z”Profile-Black
2 K AL SolarPanel Roof Kit
“L” Profile-Silver
2 K AL ColectorPanel Kit “L”Profile-Black
Product Picture No. - -
1 K AL SolarPanel Roof Kit
“L” Profile-Silver
Roof bracket for tile roof Lconnection
Roof bracket for shingle roof Z connection
Roof mounting supportingfeet
Sigma Profile- Lg:1195
Sigma Profile- Lg:2400
Sigma Profile- Lg:2400
Sigma Profile- Lg:2400
Sigma Profile- Lg:2500
Sigma Profile - Lg:3600 for 3collectors
Sigma Profile - Lg:3600 for 3collectors
Sigma Profile - Lg:3750 for 3collectors
Sigma profile connectionAadaptor
L support Part 1
L support Part 1
Z support Part 2
Z support Part 2
T bolt for Sigma profile
T›rt›l Pul
M10 nut
Bolt M8 x 70
Bolt M8 x 30
Black
Black
Blackanodisedaluminum
Grayaluminum
Blackanodisedaluminum
Grayaluminum
Grayaluminum
Blackanodisedaluminum
Grayaluminum
Blackanodisedaluminum
Grayaluminum
310 stainlesssteel
Grayaluminum
Blackanodisedaluminum
Grayaluminum
Blackanodisedaluminum
Stainlesssteel
Stainlesssteel
Stainlesssteel
Stainlesssteel
Stainlesssteel
-
-
4
4
2
-
-
-
-
-
-
-
2
-
4
-
12
12
12
16
8
-
-
4
4
-
2
-
-
-
-
-
-
-
2
-
4
12
12
12
16
8
-
4
-
4
2
-
-
-
-
-
-
-
2
-
4
-
12
12
12
16
8
-
4
-
4
-
2
-
-
-
-
-
-
-
2
-
4
12
12
12
16
8
-
-
6
4
-
-
2
-
2
-
-
-
4
-
8
-
20
20
20
36
12
-
-
6
4
-
-
-
2
-
-
-
-
-
4
-
8
20
20
20
36
12
-
6
-
4
-
-
2
-
2
-
-
-
4
-
8
-
20
20
20
36
12
-
6
-
4
-
-
-
2
-
-
-
-
-
4
-
8
20
20
20
36
12
Examples Of Baymak Forced Draft Installation Schemes
Here below there are some installation schemes that show possible installation solutions which combine a boiler
and a solar collector- The integration with solar systems for forced and natural draft installation has been
developed to grant the maximum comfort and energy saving.
COMPONENTS OF A BAYMAK SOLAR SYSTEM
1 Solar collector
2 Storage tank
3 Solar circulating group
4 Controller
5 Expansion vessel
6 Air-vent valve
7 Safety group
8 Cold water inlet
9 DHW outlet
10 Sensor of solar collectors
11 Sensor of the cylinder
12 Sensor of the boiler
13 Boiler
24
25
COMPONENTS OF
A BAYMAK SOLAR SYSTEM
1 Solar collector
2 Solar storage tank
3 Solar circulating group
4 Controller
5 Expansion vessel
6 Air-vent valve
7 Safety group
8 Cold water inlet
9 DHW outlet
10 Sensor of solar collectors
11 Sensor of the cylinder
12 Sensor of the boiler
13 Boiler
14 Mixing valve
15 Feeding sensor sanitary pump
16 Collectors distribution heating system
17 Boiler storage tank
Examples Of Baymak Forced Draft Installation Schemes
13
26
Baymak Makina San. ve Tic. A.fi.BAYMAK with its 43 years history in the heating sector has widen its product range by adding laser welded solarcollectors with 6 different models and 2 different sizes between 2,5sqm to 2.0 sqm.
Apart establishing the one of the biggest enameled hot water tank production line in recent years, Baymak builtup the most modern laser welded solar collector production line in 2009, with the annual production capacityof 375.000 sqm (150.000 pcs).
BAYMAK is a heating, cooling, water technology and solar energy company established in 1967, with its very wellknown brand name reached to 2000 sales points in Turkey and manufactures both for local market and to itsexport markets which are over 50 countries in 5 continents.�Baymak produces solar collectors, different sizes storage tanks for solar and heating, high efficient domesticand residential floor standing boilers, (pellet/log wood/coal/oil /gas), burners (raps oil /oil/lpg/gas), electricaland instant water heaters, expansion tanks and booster sets in two factories with a total closed area of 60.000square meter located is Istanbul, Turkey.�BAYMAK is a part of BDR Thermea, a world leading manufacturer and distributor of innovative heating and hotwater systems and services, operating in a market worth over 16 billion of annual sales. BDR Thermea employmore than 6.400 people across Europe with a turnover of 1.8 billion. The group has a top market position insix key countries: UK, France, Germany, Spain, the Netherlands and Italy and strong positions in the rapidlygrowing markets of Eastern Europe, Turkey, Russia, North America and China. In total BDR Thermea operatesin more than 70 countries worldwide.BDR Thermea owns and sells some of the leading brands in the European market for heating products. Theseinclude De Dietrich, Baxi, Remeha, Heatrae Sadia, Brötje, Potterton, Chappee, BaxiRoca and Baymak.
The strong R&D platform and the financial strength of BDR Thermea provide the opportunity to confirm andbuild on the leadership in the emerging market for low carbon micro combined heat and power products. Inaddition to manufacturing high efficiency boilers, BDR Thermea is committed to new heating technologies thatcan play a major role in tackling climate change. The product range already includes biomass boilers, solarcollectors and heat pump products as well as unparalleled developments in what will be tomorrow’s favouredheating solution, mCHP.
BAYMAK key of success lies in the strong commitment for :The fastest Research and Development Team,The highest technology and qualityThe most competitive pricesThe best delivery term conditions.
BAYMAK is a member of BDR Thermea www.baymak.com.tr
BAYMAK MAK‹NA SANAY‹ VE T‹C. Afi.ORHANLI BELDESI, ORTA MAHALLE AKDENIZ SOKAK NO: 8
34959 TUZLA / ISTANBUL / TURKEYTel.: 0090 216 581 65 00Fax: 0090 216 304 19 64
AgainstExpensiveEnergy
45 years“f
or
a
cleaner environme
nt”
45 years“f
or
a
cleaner environme
nt”