girbau_ms_623

Cod. 429266 Rev. 02/0606

Operation Instructions for washers LOGI CONTROL

GIRBAU, S.A. Crta de Manlleu, km. 1 08500 VIC (Barcelona) • SPAIN Tel. 34 93 8861100 Fax 34 93 8860785 [email protected] www.girbau.com For USA & CANADA:

CONTINENTAL GIRBAU Inc. 2500 State Road 44 WI 54904 Oshkosh • USA Tel. 1(920) 231-8222 Fax 1(920) 231-4666 [email protected] www.cont-girbau.com

Serial #

Shipping date

LOGI control

Cod. 429266 Rev. 02/0606

Model From serial #

High Speed

HS-6008 2.080.884

HS-6013 2.110.200

HS-6017 2.120.320

EH020 1.430.001

EH030 1.460.021

EH040 1.470.060

Medium Speed

MS-610 2.020.001

MS-613 2.030.001

MS-617 2.040.001

MS-623 2.050.001

EM025 1.370.001

EM030 1.380.001

EM040 1.390.001

EM055 1.400.001

Cod. 429266 Rev. 02/0606

3 Safety Instructions

WARNING!

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock or injury to persons when using the washer, follow basic precautions, including the following: 1. READ all instructions before using the washer and KEEP them in a prominent location for customer use. 2. Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry cleaning solvents, other flammable, or explosive substances as they GIVE OFF VAPORS that could ignite or explode.

3. DO NOT ADD gasoline, dry-cleaning solvents, or other flammable, or explosive substances to the wash

water. These substances give off vapors that could ignite or explode. 4. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for

two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

5. Do not allow children to play on or in the washer. CLOSE SUPERVISION of children is necessary when

the washer is used near children. 6. Before the washer is removed from service or discarded, REMOVE the door. 7. DO NOT TRY TO OPEN THE WASHER’S DOOR if the drum is moving. 8. Do not install or store the washer where it will be exposed to the WEATHER. 9. DO NOT TAMPER with controls. 10. DO NOT REPAIR OR REPLACE any part of the washer or attempt any servicing, unless specifically

recommended in the user instructions or in published user-repair instructions that you understand and have the skills to carry out.

11. DO NOT BY-PASS any safety device. It is NOT ACCEPTED ANY electric or mechanic MODIFICATION

OR MANIPULATION. DO NOT INSTALL foreign components inside the machine. 12. All SAFETY INSTRUCTIONS included in the Instruction Handbooks, should be reprinted and posted in the

laundry room. 13. Failure to install and operate this machine according to the Instruction Handbooks or to work safety and

hygiene standards and common sense, may result in conditions which CAN PRODUCE bodily injury or loss of life.

14. The DANGER, WARNING, CAUTION and IMPORTANT instructions appearing in the Instruction

Handbooks are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be built into this machine. These factors MUST BE supplied by the person(s) transporting, installing, maintaining, or operating the machine.

15. All connections for electrical power and plumbing MUST comply with the statutory safety standards

applicable to each country, and be made by Licensed Installers only (refer to note 3).

Cod. 429266 Rev. 02/0606


16. WARNING! MACHINE INSPECTION, FILTER CLEANING, MAINTENANCE, SERVICE OR PARTS REPLACEMENT. Before attempting any service or inspection of the washing machine: Close and mechanically interlock the water supply valves and check that machine has COMPLETELY drained, parts have cooled down and that no pieces are in movement through inertia. To reduce the risk of electrical shock: • COMPLETELY disconnect the machine from the original power source and check for accidental

reconnection. MOVING THE ON SWITCH TO THE OFF POSITION IS NOT SUFFICIENT. • Disconnect the electrical power of the external dosing to the washing machine. These circuits are

independent of the washer’s supply. • Wait a minimum of (5) five minutes after disconnection to ensure the elimination of residual voltage within

the machine. Failure to comply with this warning may result in serious injury.

17. NEVER operate the machine without the panels and guards correctly in place and secured. 18. The room SHALL comply with the environment conditions (air venting, temperature, humidity...) specified in

the Installation Instruction Handbook. NEVER INSTALL THE WASHING MACHINE in very humid environments or with water splashes.

19. DO NOT OPERATE the machine if it is suspected to be faulty, either visually, by noise or smell, or with

missing or broken parts. 20. Machine start-up SHALL be made by Authorised Service Technicians (refer to note 2). 21. Machine SHALL BE USED by qualified personnel (refer to note 1), wholly familiar with the machine’s

operation. 22. DO NOT allow children or people with handicaps incompatible to machine use to operate machine. 23. To minimise the possibility of creating a fire, take SPECIAL care, KEEP appliance area free from

combustible materials and fire extinguishers should be easily ACCESSIBLE to all laundry staff. 24. Delimitate danger areas and PREVENT public access to them with machine in operation. 25. On completion of the day's work, TURN OFF the manual supply valves and DISCONNECT the electrical

power by the External Automatic Switch. 26. Always CONTACT an Authorised Service Technician or Licensed Installer (refer to notes 2 & 3) about any

problems or conditions you do not understand. 27. For a safe operation, machine MUST be kept in a good environment, used and maintained properly, and

serviced annually by Authorised Service Technicians (refer to note 2). 28. The Distributor (seller) IS OBLIGED to thoroughly train the operator during the starting-up. THE MANUFACTURER REFUSES ANY RESPONSIBILITY IF THESE SAFETY INSTRUCTIONS AND ALL INFORMATION IN THE CORRESPONDING HANDBOOKS ARE NOT FOLLOWED. SAVE THESE INSTRUCTIONS NOTES: (1) Qualified Personnel refers to anyone who has read the Instructions Handbooks, has been trained and has a thorough understanding

of the machine’s operation (2) An Authorised Service Technician (AST) is one that has successfully completed training on the product by Girbau S.A, or a Girbau,

S.A. Distributor. (3) An Authorised Licensed Installer is one that is suitably qualified in the procedures and regulations applicable in that country.

Cod. 429266 Rev. 02/0606


HAZARD SYMBOLS USED ON WASHER LABELS:

Electric risk Protection guard for electric components. Mechanical risk Protection guard for moving parts

High temperature risk. Operate with caution. Use appropriate protections. Risk of harmful vapours inhalation. Keep dispenser box closed. Use appropriate protections.

SYMBOLS USED IN THIS MANUAL

This symbol alerts you to potential hazards for the user, the machine or the fabric.

This symbol is used to give relevance to any precise explanation

Cod. 429266 Rev. 02/0606


IMPORTANT INSTRUCTIONS FOR USE AND CONSERVATION 1. EXPECTED MACHINE USE AND DON’TS. This machine has been made and designed for washing or

cleansing in a water bath, linen and textile materials without solvent impregnation or explosives. Unless approved by the manufacturer in writing, it is not considered appropriate FOR OTHER PROCESSES.

2. Machine MATERIALS in contact with wash products are:

• Stainless Steel AISI-304 L. • Polypropylene PP. • EPDM and NBR. • Borosilicate glass. The chemicals furnisher and the machine owner will be responsible to assure that the products ARE COMPATIBLE and will not produce machine oxidation or damage. Notice that the hypochlorite (bleach), in certain conditions of use, generates chlorine gas. The chlorine is a corrosive and oxidizing substance that, in elevated concentrations and temperature, deteriorates the stainless steel and elastomers. There are other highly oxidizing agents, such as the ozone, that can cause the same effect.

3. Periodically CLEAN machine, to prevent metallic parts corrosion, to produce higher output and for a longer

life. To clean the washing machine, use water and detergent, rinse with a damp cloth, and dry. 4. NEVER use harsh products to clean the machine and laundry room. There are products on the market,

which are highly corrosive. 5. If machine is left idle for long periods of time, it must be PROTECTED from humidity and temperature

variations. 6. FOLLOW the fabric care instructions supplied by the manufacturer, GIRBAU S.A., REFUSES ANY

RESPONSIBILITY IN CASE OF TEXTILE WEAR AND TEAR. 7. Failure due to improper machine operation may VOID WARRANTY. 8. Replacing any part of the washer can affect the machine’s security.

Examples: • Just a screw or bolt of insufficient strength could cause dangerous damage. • A heater without an internal fuse could provoke a fire. • An inadequate clamp can be the cause of water leaks and short circuits... etc.

The reason for which ONLY ORIGINAL GIRBAU SPARE PARTS MUST BE USED. The incompliance of this precaution may result in a washer breakdown, a serious accident, and loss of the warranty.

9. When asking for information on your machine, MENTION model and serial number (serial plate is located

at the rear side). 10. THE ELECTRICAL DIAGRAM IS LOCATED IN THE UNDERSIDE OF THE WASHER’S TOP COVER.

Cod. 429266 Rev. 02/0606

7 Index

SAFETY INSTRUCTIONS ............................................................................................................ 3

INDEX ........................................................................................................................................... 7 1. DESCRIPTION ......................................................................................................................... 8 1.1 Characteristics ........................................................................................................................ 8 1.2 Expected use of the washer ................................................................................................... 8 2. OPERATION INSTRUCTIONS ............................................................................................... 9 2.1 Control panel .......................................................................................................................... 9 2.2 Loading the washing machine ............................................................................................ 10 2.3 Using the dispenser ............................................................................................................. 10 2.4 Starting a program ................................................................................................................ 11 2.5 Modifying a program in progress .......................................................................................... 11 2.6 Wash programs ..................................................................................................................... 11

2.6.1 Program application and contents ............................................................................... 12 2.6.2 Interpretation of the program tables ............................................................................. 17

2.7 Stop modes ............................................................................................................................. 18 2.7.1 End of cycle ................................................................................................................ 18 2.7.2 Interrupting a program ................................................................................................ 18

2.8 Unbalance control ................................................................................................................. 19 2.9 Delay option ......................................................................................................................... 19

2.9.1 Delaying a program .................................................................................................... 19 2.9.2 Programming start time ........................................................................................... 19

3. ADVANCED USE MODE. MOD mode. ............ ..................................................................... 20 3.1 Access to MODIFICATION mode 3.2. Modification of program contents. Pro menu

3.2.1Master program 3.2.2 Default program contents. General application. HS / MS models 3.2.3 Default program contents. USA / Canada application. EH020, EM025. SP-0 models 3.2.4 Default program contents. USA / Canada application. EH020, EM025. SP-1 models 3.2.5 Default program contents. USA / Canada application. Other models 3.2.6 Default program contents. UK application 3.2.7 Phases definition 3.2.8 Definition of programmable functions and values for each phase 3.2.9 Modification of a program

3.3. Information menu. Info menu 3.4. Modification of operating parameters. Mod menu

3.4.1 Parameters modification 3.5. Modification of the access code. NCod menu 3.6. Clock of the system. Hour Menu

3.6.1 To set the clock

4. TROUBLESHOOTING ........................................................................................................... 20 4.1 What to do when … ............................................................................................................... 20 4.2 System alarms ..................................................................................................................... 21 5. MAINTENANCE ..................................................................................................................... 22 5.1 Operations described … ........................................................................................................ 22 5.2 Cleaning the washer ........................................................................................................... 22 5.3 Cleaning the door seal ......................................................................................................... 22 5.4 Cleaning the electrovalve filters ........................................................................................... 22 5.5 Cleaning the dispenser ........................................................................................................ 23 5.6 Cleaning the drain pump ...................................................................................................... 24 5.7 Revising the safety mechanisms .......................................................................................... 25 5.8 General revision .................................................................................................................... 25 6. SERVICE REMOVAL .............................................................................................................. 26 6.1 Dismantling ........................................................................................................................... 26 NOTE The contents of chapter 3. ADVANCED USE MODE, can be consulted at the manufacturer’s website: www.girbau.com, (USA/CANADA: www.cont-girbau.com), see Advanced Operation Instructions for LOGI CONTROL..

Cod. 429266 Rev. 02/0606

Description 8

1. DESCRIPTION WASHER EXTRACTOR DESIGNED TO WASH OR TREAT FABRIC IN A WATER BATH. 1.1. CHARACTERISTICS Construction characteristics:

• HIGH SPEED MODELS (HS / EH). washers, capable of extracting with speeds above 350G (280G in model HS-6008/EH020) without having to be bolted down. The design of its suspension system: multi-directional springs and shock absorbers to cushion up to 95% of the vibrations produced during the spin cycle.

• MEDIUM SPEED MODELS (MS / EM). Hard-mount construction. They have to be bolted down to the floor.

• Stainless steel inner and outer drum. The openings in the drum blades promote the uniform distribution of bath water and improve the yield of the washer both during the wash and the rinse cycles.

• The drum rotation is produced by an asynchronous motor of alternating current controlled by inverter. • Hot and cold water connections with a safety mechanism to prevent contaminating by back-flowing into

the general potable water system. • Large capacity drain valve. (Option for pump drainage in models HS-6008/EH020). • Water inlets and all product dispensers done using a common collector with an anti-siphon mechanism. • Option for heating the bath using electric heaters or steam injection. Functional characteristics: • Operation control of the washer by microprocessor. • Operation of the washer adaptable to the possibilities of the installation and the needs of the user. • Washing programs: availability of eight pre-programmed programs. Each program allows for: three

phases of soak or pre-wash, wash phase with a maximum temperature of 90ºC (194ºF) and five rinse phases with a final spin at high speed.

• Great versatility in individually modifying the content of each program. (More information about the Programming Mode in the manual of Advanced Operation Instruction for the LOGI CONTROL on the manufacturer website: www.girbau.com), (USA/CANADA www.cont-girbau.com).

• Temperature control in the wash phase done by hot and cold water mixer in accordance with the programmed temperature and the activation of the heating system. Precision of +/- 2ºC (+/- 3.5ºF).

• Level control done with an electronic pressure transmitter. • communication via series between the washer microprocessor and the inverter control of the

motor. This communication takes advantage of all the features offered by inverter technology which results in a significant energy savings and an optimal management of the spin cycle. This in turn implies a significant reduction in noise, vibration and wear on the washer components.

• Multiple controls that assure the safe use of the washer. 1.2. EXPECTED USE OF THE WASHER This machine has been made and designed for industrial washing or cleansing in a water bath, linen and textile materials. Any other use will be considered contraindicated without the written authorization of the manufacturer. The washer should not be filled with a load which is much smaller or greater load than the nominal load. Laundry should not be washed when loaded in bags. If necessary, load the machine to its nominal value. It is not recommended to spin carpeting, canvas or waterproof fabrics.

Cod. 429266 Rev. 02/0606

Operation 9

2. OPERATION 2.1. Control panel

fig. 1

A: Program start and stop.

Wash program selection

ADVANCED USE mode. Begin program delay (option)

B:

Modification of the program in progress

C: ON/OFF Switch. D: LEDs indicating the phase of the program in progress. E: Display. Shows the function in progress. Main reports that appear on the display:

REPORT MEANING Pr-* Program selected. Machine ready to wash. A-* Water inlet

C-** / F*** Water temperature in Centigrade or Fahrenheit degrees

rt-* Rotation time left. Et-* Extract time left. End End of program. Door released door Washer with door open

START/STOP

MOD

ACCEL

Cod. 429266 Rev. 02/0606

Operation 10

2.2 Loading the washing machine Group the fabrics to be washed in homogeneous loads, trying to reach the nominal value of the load. Empty all pockets, fasten buttons, close zippers and remove accessories that are not machine-washable. It is not recommend mixing whites with other colours. Open the door and load the machine. We recommend filling the drum to its nominal load. Do not overload the machine; the door must be able to close easily. Whilst the door is open, the display reads door, indicating that the door must be closed in order for the program to begin. 2.3 Using the dispenser Fill the compartments with the corresponding products, according to these symbols:

fig. 2 fig. 3

- Powdered detergent for pre-wash.

- Powdered detergent for wash.

∆ - Liquid bleach (chlorine, bleach...)

- Liquid softener / neutraliser.

For safety, close dispenser drawer or cover before starting the wash cycle.

SUDS CONTROL. The mechanical action of front-loading washing machines improves the quality of the wash but encourages creation of suds. Remember that a suds bath always reduces the efficiency of your wash. ALWAYS USE CONTROLLED SUDS DETERGENT. Models EH020 & EM025 incorporate a group of programmes (SP-I) for a superior rinse efficiency. Oversudsing causes an increase in the pressure inside the machine and decreases the efficiency of the sealing systems. Repeated washing with a large amount of suds considerably reduces the life of seals and bearings. THIS CIRCUMSTANCE IS NOT COVERED BY THE MACHINE’S WARRANTY.

Cod. 429266 Rev. 02/0606

Operation 11

2.4 Starting a program • Close the door. The door report on display changes to SEL. (if SEL does not appear on the display,

repeat the door closing operation). • Select the desired program with the program selection keys. (For information on the characteristics of

each program, refer to section 2.6. Wash Programs). The selected program number will be shown on the display.

• Place the washing products in the dispenser and close it. • After pressing the START/STOP key, the temperature value will appear for the washing phase. • The / keys modify the temperature for the program to be run. This option can be disabled in the MOD

menu (Advanced Operation Instructions) • Press the START/STOP key again to confirm the temperature selected and start the washing program.

Once the program has finished, the temperature is reset back to its programmed value. • Throughout the program’s duration, the display will show the various operations run by the washer (refer

to section 1.1) and door remains locked until the LED indicating the end of the program comes on. Door lock. After giving the start order, a 30-second security time is started during which the drum rotation and the water inlet operate at short impulses and door remains released. At the end of this time, the locking mechanism closes and the wash cycle begins.

2.5 Modifying a program in progress Program acceleration You can modify the duration of a program whilst it is in progress. • Press the key to activate the option. The display will flash. • By pressing the key repeatedly it is possible to increase the rotation time minute by minute. The

duration of the spin cycle cannot be increased. • By pressing the key repeatedly it is possible to decrease the rotation or spin times.

• Passing to the subsequent phase. The passing from one phase to the next is delayed. Press the key until the end of the phase and wait a few moments until the first operation of the next phase appears. Continue pressing the key.

• After a few seconds without pressing any key, the display will remain fixed and the modification option is deactivated.

Crease-guard stop Once the washing program has started, you can program to stop the drum rotation before the final extract, with the objective of avoiding creases. For activating this function once the washing cycle has started, press the key for some seconds. On the display, the rh-0 message will appear. Press . The display message will change to rh-I. The crease-guard Stop function has been activated. Before the last extract, the drum rotation will be interrupted and the PUSH STAR message will appear on the display. For resuming the program, press the START/STOP key. 2.6 Wash programs The washer offers the possibility to select among eight different wash programs for different kind of garment and soil. In the default configuration, the program contents is defined as indicated in the following charts:

MOD

ACCEL

Cod. 429266 Rev. 02/0606

Operation 12

2.6.1. Program application and contents General application. HS / MS models

Pr - 1. EXTRA HEAVY SOIL - WHITE 66 MIN. Pr - 2. HEAVY SOIL – WHITE 56 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 20 1 1 2 - - - - - - 0 - - - 1 2 20 0 1 2 - - - - - - 1 - - -2 2 40 0 1 6 - - - - - - 1 - - - 2 2 30 1 1 6 - - - - - - 3 3 3 2 60 1 1 6 - - - - - - 3 3 3 1 60 2 1 10 0 - - - 2 2 4 1 80 2 1 12 0 - - - 2 2 4 2 40 3 1 6 - - - - - - 1 - - -5 2 40 3 1 6 - - - - - - 1 - - - 5 3 - - - 0 1 2 - - - - - - 3 3 6 3 - - - 0 1 2 - - - - - - 3 - - - 6 3 - - - 0 1 2 - - - - - - 1 - - -7 3 - - - 0 1 2 - - - - - - 1 - - - 7 2 0 4 1 4 - - - 0 6 7 8 2 0 4 1 4 - - - 0 6 7

Pr - 3. MEDIUM SOIL - WHITE 51 MIN. Pr - 4. LIGHT SOIL – WHITE 37 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 40 1 1 6 - - - - - - 3 3 1 1 40 2 1 6 1 - - - 0 - - -2 1 50 2 1 8 0 - - - 2 2 2 2 30 3 1 6 - - - - - - 1 - - -3 2 30 3 1 6 - - - - - - 1 - - - 3 3 - - - 0 1 2 - - - - - - 3 3 4 3 - - - 0 1 2 - - - - - - 3 3 4 3 - - - 0 1 2 - - - - - - 1 - - -5 3 - - - 0 1 2 - - - - - - 1 - - - 5 2 0 4 1 4 - - - 0 6 7 6 2 0 4 1 4 - - - 0 6 7

Pr - 5. HEAVY SOIL – COLOR 51 MIN. Pr - 6. MEDIUM SOIL - COLOR 40 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 0 0 1 4 - - - - - - 1 - - - 1 2 30 1 2 4 - - - - - - 2 2 2 2 40 1 1 6 - - - - - - 3 3 2 1 40 2 1 8 0 - - - 2 2 3 1 50 2 1 10 0 - - - 2 2 3 3 - - - 0 2 2 - - - - - - 3 3 4 3 0 0 1 2 - - - - - - 3 3 4 3 - - - 0 2 2 - - - - - - 1 - - -5 3 - - - 0 1 2 - - - - - - 1 - - - 5 2 0 4 2 4 - - - 0 6 7 6 2 0 4 1 4 - - - 0 6 7

Pr - 7. SYNTHETICS 30 MIN. PR - 8. WOOL & DELICATE 31 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 1 40 2 2 6 0 - - - 2 2 1 3 0 1 3 4 - - - - - - 1 - - -2 3 - - - 0 2 2 - - - - - - 3 3 2 3 30 2 3 8 1 - - - 1 - - -3 3 - - - 0 2 2 - - - - - - 1 - - - 3 3 - - - 0 3 2 - - - - - - 1 - - -4 2 0 4 2 4 - - - 0 6 6 4 3 - - - 0 3 2 - - - - - - 1 - - - 5 3 0 4 3 4 - - - 0 2 2

The parameters that appear on the chart can be modified: See the Advanced Operation Instructions LOGI CONTROL at the manufacturer’s website: www.girbau.com, (USA/CANADA www.cont-girbau.com).

Cod. 429266 Rev. 02/0606

Operation 13

USA/Canada application. EH020, EM025. SP-0 models

PR - 1. EXTRA HEAVY SOIL - WHITE 23 MIN. PR - 2. HEAVY SOIL - WHITE 17 MIN. Ph L F d r rt cd rh E Et Ph L F d r rt cd rh E Et 1 1 104 2 1 7 0 - - - 1 - - - 1 1 95 2 1 4 0 - - - 1 - - -2 1 32 3 2 2 - - - - - - 2 2 2 2 32 3 2 2 - - - - - - 2 2 3 2 - - - 0 2 1 - - - - - - 1 - - - 3 2 32 4 2 2 - - - 0 5 4 4 2 32 4 2 2 - - - 0 5 4

PR - 3. MEDIUM SOIL - WHITE 17 MIN. PR - 4. LIGHT SOIL - WHITE 17 MIN. Ph L F d r rt cd rh E Et Ph L F d r rt cd rh E Et 1 1 86 2 1 4 0 - - - 1 - - - 1 1 68 2 1 4 1 - - - 1 - - -2 2 32 3 2 2 - - - - - - 2 2 2 2 32 3 2 2 - - - - - - 2 2 3 2 32 4 2 2 - - - 0 5 4 3 2 32 4 2 2 - - - 0 5 4

PR - 5. HEAVY SOIL - COLOR 18 MIN. PR - 6. MEDIUM SOIL - COLOR 16 MIN. Ph L F d r rt cd rh E Et Ph L F d r rt cd rh E Et 1 1 95 2 1 6 0 - - - 1 - - - 1 1 95 2 1 4 0 - - - 1 - - -2 2 32 0 2 1 - - - - - - 2 2 2 2 32 0 2 1 - - - - - - 2 2 3 2 32 4 2 2 - - - 0 5 4 3 2 32 4 2 2 - - - 0 5 4

PR - 7. SYNTHETICS 16 MIN. PR - 8. WOOL & DELICATE 15 MIN. Ph L F d r rt cd rh E Et Ph L F d r rt cd rh E Et 1 1 86 2 2 4 0 - - - 1 - - - 1 2 68 2 2 4 1 - - - 1 - - -2 2 32 0 2 1 - - - - - - 2 2 2 2 32 0 3 1 - - - - - - 1 - - -3 2 32 4 2 2 - - - 0 5 4 3 2 32 4 3 2 - - - 0 3 3


Cod. 429266 Rev. 02/0606

Operation 14

USA/Canada application. EH020, EM025. SP-1 models

PR - 1. EXTRA HEAVY SOIL - WHITE 35 MIN. PR - 2. HEAVY SOIL - WHITE 28 MIN. Ph L F d r rt cd rh E Et Ph L F d r rt cd rh E Et 1 1 113 2 1 12 0 - - - 1 - - - 1 1 104 2 1 8 0 - - - 1 - - -2 2 32 3 1 3 - - - - - - 3 2 2 2 32 3 1 2 - - - - - - 3 2 3 3 - - - 0 1 1 - - - - - - 1 - - - 3 3 - - - 0 1 2 - - - - - - 1 - - -4 2 - - - 0 1 2 - - - - - - 1 - - - 4 2 32 4 1 2 - - - 0 6 5 5 2 32 4 2 2 - - - 0 6 5

PR - 3. MEDIUM SOIL - WHITE 28 MIN. PR - 4. LIGHT SOIL - WHITE 25 MIN. Ph L F d r rt cd rh E Et Ph L F d r rt cd rh E Et 1 1 104 2 1 8 0 - - - 1 - - - 1 1 68 2 1 5 1 - - - 1 - - -2 2 32 3 1 3 - - - - - - 3 2 2 2 32 3 1 3 - - - - - - 3 2 3 3 - - - 0 1 2 - - - - - - 1 - - - 3 3 - - - 0 1 2 - - - - - - 1 - - -4 2 32 4 2 2 - - - 0 6 5 4 2 32 4 1 2 - - - 0 6 5

PR - 5. HEAVY SOIL - COLOR 28 MIN. PR - 6. MEDIUM SOIL - COLOR 26 MIN. Ph L F d r rt cd rh E Et Ph L F d r rt cd rh E Et 1 1 104 2 1 10 0 - - - 1 - - - 1 1 104 2 1 8 0 - - - 1 - - -2 2 32 0 2 1 - - - - - - 3 2 2 2 32 0 2 1 - - - - - - 3 2 2 3 - - - 0 2 2 - - - - - - 1 - - - 2 2 - - - 0 2 1 - - - - - - 1 - - -3 2 32 4 2 2 - - - 0 6 5 3 2 32 4 2 2 - - - 0 6 5

PR - 7. SYNTHETICS 23 MIN. PR - 8. WOOL & DELICATE 23 MIN. Ph L F d r rt cd rh E Et Ph L F d r rt cd rh E Et 1 1 86 2 2 5 0 - - - 1 - - - 1 2 68 2 2 8 1 - - - 1 - - -2 2 32 0 2 1 - - - - - - 3 2 2 2 32 0 3 1 - - - - - - 1 - - -2 3 - - - - - - 2 2 - - - - - - 1 - - - 2 3 - - - - - - 3 2 - - - - - - 1 - - -3 2 32 4 2 2 - - - 0 6 5 3 2 32 4 3 2 - - - 0 4 3


Cod. 429266 Rev. 02/0606

Operation 15

USA/Canada application. All models

Pr - 1. EXTRA HEAVY SOIL - WHITE 54 MIN. Pr - 2. HEAVY SOIL - WHITE 44 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 2 2 86 0 1 5 - - - - - - 1 - - - 2 2 86 1 1 3 - - - - - - 3 2 3 2 104 1 1 3 - - - - - - 3 3 3 1 149 2 1 8 0 - - - 2 2 4 1 176 2 1 11 0 - - - 2 2 4 2 86 3 1 6 - - - - - - 3 2 5 2 104 3 1 6 - - - - - - 3 2 5 3 - - - 0 1 2 - - - - - - 1 - - -6 3 - - - 0 1 2 - - - - - - 1 - - - 6 3 - - - 0 1 2 - - - - - - 1 - - -7 3 - - - 0 1 2 - - - - - - 1 - - - 7 2 0 4 1 3 - - - 0 6 6 8 2 32 4 1 3 - - - 0 6 6

Pr - 3. MEDIUM SOIL - WHITE 42 MIN. Pr - 4. LIGHT SOIL - WHITE 30 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 86 1 1 3 - - - - - - 3 2 1 2 104 2 1 6 1 - - - 0 - - -2 1 131 2 1 8 0 - - - 2 2 2 2 86 3 1 4 - - - - - - 3 2 3 2 86 3 1 5 - - - - - - 3 2 3 3 - - - 0 1 2 - - - - - - 1 - - -4 3 - - - 0 1 2 - - - - - - 1 - - - 4 3 - - - 0 1 2 - - - - - - 1 - - -5 3 - - - 0 1 2 - - - - - - 1 - - - 5 2 32 4 1 2 - - - 0 6 6 6 2 32 4 1 2 - - - 0 6 6

Pr - 5. HEAVY SOIL – COLOR 46 MIN. Pr - 6. MEDIUM SOIL - COLOR 37

Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 32 0 1 3 - - - - - - 1 - - - 1 2 86 1 1 3 - - - - - - 3 2 2 2 104 1 1 5 - - - - - - 3 2 2 1 104 2 1 9 0 - - - 2 2 3 1 122 2 1 11 0 - - - 2 2 3 3 - - - 0 2 2 - - - - - - 3 2 4 3 - - - 0 1 2 - - - - - - 3 2 4 3 - - - 0 2 2 - - - - - - 1 - - -5 3 - - - 0 1 2 - - - - - - 1 - - - 5 2 32 4 2 3 - - - 0 6 6 6 2 32 4 1 3 - - - 0 6 6

Pr - 7. SYNTHETICS 30 MIN. PR - 8. WOOL & DELICATE 29 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 104 2 2 8 0 - - - 2 2 1 3 32 1 3 3 - - - - - - 1 - - -

- - - 3 - - - 0 2 2 - - - - - - 3 2 2 3 86 2 3 8 1 - - - 1 - - -3 3 - - - 0 2 2 - - - - - - 1 - - - 3 3 - - - 0 3 2 - - - - - - 1 - - -4 2 32 4 3 4 - - - 0 6 6 4 3 - - - 0 3 2 - - - - - - 1 - - - 5 3 32 4 3 3 - - - 0 2 2


Cod. 429266 Rev. 02/0606

Operation 16

UK application

Pr – 1. HEALTHCARE 49 MIN. Pr - 2. HEAVY SOIL – WHITE 59 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 0 0 1 2 - - - - - - 1 - - - 1 2 20 0 1 4 - - - - - - 1 - - -

2 2 0 1 1 2 - - - - - - 3 3 2 2 30 1 1 6 - - - - - - 3 3

3 1 65 2 1 12 0 - - - 2 2 3 1 60 2 1 10 0 - - - 2 2

4 2 40 3 1 6 - - - - - - 1 - - - 4 2 40 3 1 6 - - - - - - 3 3

5 3 - - - 0 1 2 - - - - - - 1 - - - 5 3 - - - 0 1 2 - - - - - - 1 - - -

6 2 0 4 1 4 - - - 0 6 7 6 3 - - - 0 1 2 - - - - - - 1 - - -

7 2 0 4 1 4 - - - 0 6 7

Pr - 3. MEDIUM SOIL – WHITE 51 MIN. Pr - 4. LIGHT SOIL – WHITE 37 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 30 1 1 6 - - - - - - 3 3 1 1 40 2 1 6 1 - - - 0 - - -

2 1 50 2 1 8 0 - - - 2 2 2 2 30 3 1 6 - - - - - - 3 3

3 2 30 3 1 6 - - - - - - 3 3 3 3 - - - 0 1 2 - - - - - - 1 - - -

4 3 - - - 0 1 2 - - - - - - 1 - - - 4 3 - - - 0 1 2 - - - - - - 1 - - -

5 3 - - - 0 1 2 - - - - - - 1 - - - 5 2 0 4 1 4 - - - 0 6 7

6 2 0 4 1 4 - - - 0 6 7

Pr - 5. HEAVY SOIL – COLOR 51 MIN. Pr - 6. MEDIUM SOIL – COLOR 40 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 2 0 0 2 4 - - - - - - 1 - - - 1 2 30 1 2 4 - - - - - - 2 2

2 2 30 1 2 6 - - - - - - 3 3 2 1 40 2 1 8 0 - - - 2 2

3 1 40 2 1 10 0 - - - 2 2 3 3 0 0 2 2 - - - - - - 3 3

4 3 0 0 2 2 - - - - - - 3 3 4 3 - - - 0 2 2 - - - - - - 1 - - -

5 3 - - - 0 2 2 - - - - - - 1 - - - 5 2 0 4 2 4 - - - 0 6 7

6 2 0 4 2 4 - - - 0 6 7

PR - 7. SYNTHETICS 30 MIN. PR - 8. WOOL AND DELICATES 32 MIN. Ph L C d r rt cd rh E Et Ph L C d r rt cd rh E Et 1 1 40 2 2 6 0 - - - 2 2 1 3 0 1 3 4 - - - - - - 1 - - -

2 3 0 0 2 2 - - - - - - 3 3 2 2 30 2 2 8 1 - - - 1 - - -

3 3 - - - 0 2 2 - - - - - - 1 - - - 3 3 0 0 3 2 - - - - - - 1 - - -

4 2 0 4 2 4 - - - 0 6 6 4 3 - - - 0 3 2 - - - - - - 1 - - -

5 3 0 4 3 4 - - - 0 4 3 The parameters that appear on the chart can be modified: See the Advanced Operation Instructions LOGI CONTROL at the manufacturer’s website: www.girbau.com (USA/CANADA www.cont-girbau.com).

Cod. 429266 Rev. 02/0606

Operation 17

2.6.2. Interpretation of the program tables: symbols and values. SYMBOL OPTION DESCRIPTION

Estimated program time Minimum program time based on a machine with hot water supply and without heating. Time in minutes.

Ph

Phase number. The phase indicated with grey background belongs to the wash phase.

L

1 2 3

Bath level Low level Medium level High level (units with pumped drain, levels 2 and 3 are the same)

C / F

Bath temperature Value in Centigrade or Fahrenheit degrees

d

0 1 2 3 4

Dosing Phase without dosing Pre-wash dosing Wash dosing Bleach dosing Softener / neutraliser dosing

r

1 2 3

Drum rotation Heavy-duty rotation: 25 sec. ON / 5 seconds stop. Normal rotation: 15 sec. ON / 15 seconds stop. Delicate rotation: 5 sec. ON / 25 seconds stop.

rt

Rotation time Value in minutes

c

0 1

Gradual cool down Option non available Option available

rh

0 1

Program stop in the last rinse (rinse hold) Option non available Option available

E

1 2 4 6

Bath drain Drain + wash speed Drain + positioning speed Drain + medium spin speed Drain + high spin speed

Et

- - - -

Spin time Value in minutes Non programmable value in the phase

Cod. 429266 Rev. 02/0606

Operation 18

2.7 Stop modes 2.7.1 End of cycle The buzzer and the LED indicating the end of the cycle inform that the program has finished and the door lock is released. 2.7.2 Interrupting a program A. Key START/STOP . Interrupting a washing program. STOP appears on the display. At the end of the safety

delay, the buzzer and the LED indicating the end of cycle inform that the program has finished and the door lock is released.

B. Emergency stop. (except MS-610 / EM025, HS-6008 / EH020 models) Pressing once on the EMERGENCY switch interrupts the washer operation and opens the drain valve. ALM/EMER appears on the display. After a delay of approximately 3 minutes, the door is released. To resume the wash cycle, release the switch and press ONCE the key START/STOP . To cancel the wash cycle, release the switch and press TWICE the key START/STOP .

C. Other stop modes are: • Disconnecting the ON/OFF switch. • Disconnecting the external automatic switch. We do not recommend these stop modes, except in an emergency. In these cases, as long as the door remains closed, the machine will understand that there has been a power failure. When the power is switched back on, the machine will resume the program in progress.

D. Interruption of the power supply. The operation of the washing machine is interrupted: the drain valve opens and after a delay of approximately 3 minutes, the door is released. If the door remains closed when the power supply is restablished, the wash cycle is resumed. If the door is open, the wash cycle is cancelled.

On machines with pumped drain, the disconnection of the external automatic switch or the ON switch do not allow the bath drain.

When a washing program is interrupted by electrical power failure, disconnecting the ON switch, or activating the Emergency Stop, the door lock mechanism stops being controlled by the microprocessor and the opening of the door is thermally delayed. In these circumstances, it is normal to have a washer delay or inactive time of about 3 minutes.

Risk of entrapment To avoid the risk that, while playing, a child gets entrapped inside a washer IT IS CAUTIONED THAT: • After giving the start order, a safety delay of 30 seconds starts during which the drum rotation and the

entry of water operate at short impulses and the door remains released (see section 2.4) • All the mechanisms that interrupt a program described in this section:

- stop the washer motor - open the drain valve - disconnect the door lock which can be opened after approximately 3 minutes.

Cod. 429266 Rev. 02/0606

Operation 19

2.8. Unbalance control Before starting spin, the electronic control of the washing machine checks the correct distribution of the load. If it detects that the load is not well distributed and that can cause an excessive unbalance during the spin, a new positioning of the clothes will be carried out. If there’s still unbalance during the spin of the last phase, the washer can end the washing cycle reducing the spin speed. Unbalance control with a micro-switch. Activates only in cases of extreme unbalance.

To improve the efficency of the spin of the washer it’s advisable to: • Load the washer until its nominal value. • Load the washer with homogeneous loads

2.9 DELAY option

The DELAY option allows you to program the start time of a program depending on the needs of the user. For example: using two-rate electricity, rationalisation of electricity consumption, adjusting the laundry production system, etc.

To use the DELAY option, it is essential for the washing machine to have a real-time operation kit installed (clock). If the machine did not come with this kit, you can install one easily. Contact your distributor. Before the first use, and each time there is a time change, verify and/or adjust the time on the clock. (See ADVANCED USE MODE, sect. 2.5 at www.girbau.com) (USA/CANADA: www.cont-girbau.com) 2.9.1 Delaying a program. • Load the washing machine and close the door. • Place washing products in the dispenser compartment. • Select the program to be used and press the button. The dLY report will appear on the display. • To cancel the dLY option, press the START/STOP button 2.9.2. Programming start time • When dLY is displayed, press the button. The current time will appear on the screen, in “h,m”

format (hours, minutes, using a 24-hour clock). • The minutes are shown flashing. You can change them by pressing the buttons . • Press the button to validate the minutes and start to modify the hours. • The hours are shown flashing. You can change them by pressing the buttons . • Once you have chosen the desired start time, push START/STOP . The start time and the selected

program will be displayed alternatively. • To cancel the delay of a program, select and hold START/STOP button, for five seconds.

ACCEL

MOD

MOD

Cod. 429266 Rev. 02/0606

Advanced Mode / Troubleshooting 20

3. ADVANCED USE MODE. MOD mode.

There is an advanced use mode: the MOD mode. This mode includes five different menus through which each user can personalise the operation of the washing machine. Menus for advanced use mode:

MENU PURPOSE Pro Modification of the program contents

INFO Information menu Mod Modification of operation parameters Ncod Modification of the access code HOUR Adjustment of the system time

Information on the menus, details and access mode: refer to the Advanced Operation Instructions for LOGI CONTROL, at the manufacturer’s website: www.girbau.com. (USA/CANADA www.cont-girbau.com). 4. TROUBLESHOOTING Some of the washing machine’s operating problems can be solved through the intervention of the user. These problems are detailed below. Should you have any questions, remember to consult the Authorised Technical Service. 4.1 What to do when… ....the wash cycle ends with the report: END/BAL This report indicates that the final spin cycle is not possible because the load is unbalanced. • Unload the machine and load it again. • Begin the wash cycle and accelerate the program to the last phase. • The washing machine will repeat the last spin cycle without refilling with water. • If the problem persists, or occurs often, contact the Authorised Technical Service.

….the machine makes a strange noise during the spin cycle. • Check the levelling of the machine. See Instruction Manual for Installation. • Tighten the locking screws on the outside panels. • If the problem persists, contact the Authorised Technical Service.

.... the door may have a leak • Clean the door seal of any possible deposits or remains of cloth

.... there is water leaks inside the washer cabinet.

• Check the outlet draining pipe. • Check the seals on the water inlet hoses; tighten the connection couplings. • Check the condition of the door seal and if there are any ruptures. • machines with pumped darain: Check the coupling of the filter and the draining pump (section 4.6) • if the problem persists, seal all of the water inlets and contact the Authorised Technical Service.

….you have forgotten the access code for the advanced operating mode

• Contact the Authorised Technical Service. .... the clock (option) stops working correctly

• Possible battery failure. Contact the Authorised Technical Service to have it replaced.

Cod. 429266 Rev. 02/0606

Troubleshooting 21

4.2 System alarms The safety of the washing machine use requires that the machine itself precisely monitor any possible anomalies. These anomalies are reported in the form of alarms. On the washing machine’s display, the ALM message will appear, alternating with the specific alarm report. Below are possible causes of alarms and the steps to follow.

REPORT ON THE

DISPLAY PROBABLE CAUSE WHAT TO DO

Faulty water inlet

Check water input pressure. Check manual water inlet valves. Check the status of the filters in the electrovalves (see section 5: Maintenance).

ALM/A-*

Defect in the electrovalves. Defect in the level control system. Call Service

Machines with pump drain: obstruction of the draining pump. Call Service

ALM/E Anomaly in the drain system. Erroneous drain configuration.

Check the status of the washing bath’s output hoses. Call Service

ALM/HOT

Inadequate stop of the washing machine with bath at high temperature. Excess of temperature with machine stopped. Anomaly in the heating system.

Close the door of the washing machine to allow opening of cold water valve. Press STOP key to drain the bath and access to the door opening. Repeat this operation until the alarm report disappears. If the alarm report does not disappear after five attempts, disconnect the general power supply and close water inlet manual valves. Call Service

ALM/L Leakage in the electrovalve. Bath level with machine idle.

Close manual water inlet valves Call Service

ALM/SL Bath level exceeded. Close manual water inlet valves Call Service

ALM/C Defect in the temperature probe. Erroneous heating configuration. Defect in the heating circuit.

Call Service

ALM/Prob Defect in the temperature probe. Call Service

ALM/BAL Defect in the unbalance control switch. Call Service

ALM/VAR* Disconnection of the motor’s thermal protection. Alarm set off by the inverter.

Call Service

ALM door Faulty door lock Call Service

Hot Interruption of the program by STOP key with bath at high temperature.

The washing machine will automatically accept cold water and will not allow door unlock. When the bath temperature is below 45ºC (133F) the bath will drain and the safety door lock will be unlocked.

door Badly closed door Open and close door

Cod. 429266 Rev. 02/0606

22 Maintenance

5. MAINTENANCE

- Before performing any work on the washing machine, disconnect and mechanically lock the

external switch, and close and mechanically lock the manual water inlet valves. - Check the temperature of the parts to be handled, to avoid the risk of burns. - The dispenser may contain residues of chemical products. When handling this component, avoid

direct contact with the skin and use eye protection. - The draining pump and valve may contain residual water. When handling these components,

avoid direct contact with the skin and use eye protection. - Remember to reassemble ALL of the panels and place them correctly after any maintenance work. 5.1 Operations described • Cleaning the washer (section 5.2) • Cleaning the door seal (section 5.3). • Cleaning the electro valve filters (section 5.4) • Cleaning the dispenser (section 5.5) • Cleaning the draining pump (models HS-6008/EH020 with pumped drain) (section 5.6) 5.2. Cleaning the washer • We recommend periodic cleaning of the outside of the washing machine. Use a damp cloth or sponge. • To remove traces of grease, use mild soap and rinse as required. • Never use abrasive products or tools that could scratch or damage the surface of the washing machine. 5.3. Cleaning the door seal • Use a damp cloth or sponge. • Be especially careful to remove traces of laundry products or pieces of fabric that could be caught

between the folds of the seal. • Never use abrasive products or tools that could cut or damage the seal. 5.4. Cleaning the electro valve filters Tools required: • Disassembly of the fittings: Slip-joint plier or pipe wrench diam. 1-½ in. (35 mm). • Disassembly of the filter supports: wrench 1-3/8 in. (34 mm). • Disassembly of the filtres: pliers. Steps to follow • Disconnect and mechanically lock the external switch. Close and mechanically lock the manual water

inlet valves. • Check the temperature of the hot water inlet hose, so as to avoid the risk of burns. • Disassemble the fittings that connect the hoses to the washing machine. • Disassemble the filter supports (according to model). • Remove the filters from their housings and clean the filters with pressurised water. Place them back into

their housings. • Assemble the supports to the electrovalves (according to model). • Assemble the hoses in their corresponding inputs. Tighten the fittings. • Connect the external switch, open the manual water input valves and check the water tightness of the

coupling.

Cod. 429266 Rev. 02/0606

23 Maintenance

5.5. Cleaning the dispenser • Disconnect and mechanically lock the external switch. Close and mechanically lock the manual water

inlet valves • Clean the dispenser by using a cloth or sponge dampened with water. Warm water makes cleaning

easier. Never use abrasive products or tools that could scratch or damage the dispenser. Once the dispenser cleaning and assembly operations are finished: • Connect the external switch and open the manual water inlet valves. • Start a washing program that uses a bleaching agent and softener and check that both compartments

drain properly.

fig. 4 fig. 5 WASHERS WITH FRONT DISPENSER. Tools required: Disassembly of the fastening tabs: Torx. T20 screwdriver. Disassembly and assembly: • Open the dispenser drawer and loosen the screws on the retaining tabs visible along the bottom (fig. 4). • Completely remove the drawer and dismount the siphon tubes from the liquid compartment by pulling

them upwards. Once the cleaning operations are over: • Replace the siphon tubes and place the drawer in its housing. • Remount the fastening tabs and check that the drawer can not be completely removed. WASHERS WITH TOP DISPENSER. Disassembly • Open the fastening clasps on the top cover. The dispenser is now accessible. • Dismount the siphon tubes from the liquid compartment by pulling them upwards. • To clean the lower basin, remove the leak seal and separate the two dispenser bodies by separating the

side lips (fig. 5). Once the cleaning operations are over: • Remount the two dispenser bodies and check that the side lips fasten both pieces. • Replace the siphon tubes. • Check that the dispenser is set well in its bracket. • Check condition of top cover seal. If seal is damaged, deformed or has lost elasticity, call Service for

replacement. • Replace the seal. Assemble the top cover. Close the locks.

Cod. 429266 Rev. 02/0606

24 Maintenance

VERY IMPORTANT The protection of dispenser seal is necessary to prevent humidity and corrosion inside the machine and the premature damage of the electrical and electronic circuits of machine control. 5.6. Cleaning the drain pump (Drain pump washers)

Only by the Authorised Technical Service Required tools: Disassembly of the lower front panel: Torx. T25 screwdriver. • Before disassembling the lower front panel of the washing machine, disconnect and mechanically lock

the external switch, and close and mechanically lock the manual water inlet valves. • Empty any residual water contained in the drain ducts, placing the corrugated rear tube horizontally on

the floor. The water will come out of the end. • Disassemble the lower front panel. The draining pump is accessible. • Turn the filter counter-clockwise and separate it from the pump body

fig. 6 • Clean the filter and the possible deposits from the inside of the pump body. • Assemble the filter and the draining pump. • Assemble the lower panel.

The bottom front cover is a stabilising element of the washer cabinet. Make sure that it is properly mounted and fastened. • Connect the external switch and open the manual water inlet valves. • Begin a washing program and check that there are no water leaks

Cod. 429266 Rev. 02/0606

25 Maintenance

5.7. Revising the safety mechanisms. MONTHLY check the safety mechanisms on the door lock and the emergency stop.

CAUTION Use great prudence in checking the safety mechanisms. Carry out the verification described in following while the drum is turning at washing speed and never at a higher speed. If there is a failure in the door lock, never place one’s hand in the loading area of the washer. Verification procedure: Disconnect the ON/OFF switch. The display is off. Close and mechanically lock the manual water inlet valve (and steam inlet valves for washers with this option). Open the washer door. Connect the ON/OFF switch. The display will read door. Close the door. The display will read Pr-1. Select and start a wash cycle. After about a minute from starting the cycle, check that the door is locked. Appliances with Emergency Push-Button only Then activate the EMERGENCY button. The buzzer will sound and the drum will stop rotating. The display will read ALM EMER. Unlock the emergency button and press the STOP key. Press the STOP key. After a safety delay of about 3 minutes, the door will be released. The verification is finished. If no anomaly has been detected, open the fluid inlet valves.

CAUTION If noticing anything other than what was described during the operation, disconnect the washer, do not use it, and URGENTLY contact the Authorised Technical Service. 5.8. General Revision

Only by the Authorised Technical Service. • As preventive maintenance action, it is very important to ask the Authorised Technical Service for a

periodic overhaul of the washing machine. • Recommended periodicity: every year or each 3000 washing cycles. • When performing this operation in models HS-6008 (EH020), due to the fatigue they are subject to, we

recommend carefully checking the door seal and replacing if wear is noticed.

Cod. 429266 Rev. 02/0606

26 Service Removal

6. SERVICE REMOVAL

• Removing the washer from service requires a specialised company. • Never release the washer unsecured. • To release the washer and subsequent transportation, refer to the same specifications and

cautions indicated for Installation. When removing the machine from service: • Disconnect the external switch and lock it mechanically. Remove the power wires. • Close and mechanically interlock the manual water supply valves. Remove water supply hoses. • Disassemble the drain outlet pipe and empty any residual water left in the washing machine. • Assemble the shipping restraints. • Disassemble the door of the washing machine (consult the Authorised Technical Service). 6.1 Dismantling Most of the machine’s components are made with recyclable or recoverable materials. The injected pieces bear information on the materials that were used to make them. The main materials are: • Steel plates. • Stainless plate. • Grey cast iron. • Aluminium • Glass • Polypropylene (PP) • Ethylene Propylene (EPDM) • ABS. • Copper. • Electronic components

Management of waste electronic equipment. The manufacturer is obliged to advise that in compliance with directive 2002/96/EC about management of waste electronic equipment: • The electronic components installed in the washing machine, must be dismantled and delivered to

treatment facilities authorised for this purpose. • If it is not possible to deliver to an authorised treatment facility, the manufacturer will be in charge of

collecting and managing this waste through his distributors or Authorised Service.

Documents

girbau_ms_623