Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
INSULATION FIXINGS
GUIDE20
21
VERS
ION
1.0
WE HAVE A RANGE OF PROMOTIONAL FLYERS AND INFORMATIVE HAND OUTS ALSO AVAILABLE Sales and Customer Service
Tel: +44 (0) 141 647 7100Fax: +44 (0) 141 647 5100
Email: [email protected]
CONTENTS
INSULATION FIXINGS
SELF DRILLING INSULATION SCREWS - PHILLIPS/TORX
SELF-DRILLING INSULATION SCREWS – A4 STAINLESS STEEL
INSULATION ANCHORS
HEAVY DUTY ROOFING SCREWS
COMPOSITE PANEL - TEK® 3
A2/A4 STAINLESS COMPOSITE SCREWS
A4 BI-METAL MASONRY SCREW
SELF TAPPING MASONRY SCREW
CEMENTITIOUS BOARD SCREWS
TIMBER TEK
A2 STAINLESS BI-METAL WING-DRILL TEK SCREW
SELF-DRILLING CEMENTITIOUS BOARD SCREW
STRESS PLATES
INSULATION RETAINING WASHERS
PANEL-FIX
PAGE
6
7
8
9
10
11
12-13
14-15
16
17
18
19
20
21
22
4
CONTENTS
INDEX 46-47
TECHNICAL INFORMATION
SPECIFICATIONS AND LABORATORY SERVICES
PAGE
24-25
FIXING FINDER
FIXING INSULATION PRODUCTS TO STEEL AND TIMBERSUBSTRATES IN INTERNAL AND EXTERNALAPPLICATIONS
PIR, PUR, XPS, EPS, PF AND PE INSULATION BOARDS
GLASS, ROCK, STONE AND MINERAL WOOL ROLLS, BATTENS, MATTRESSES AND BOARDS
FIXING STRUCTURAL, TRAPEZOIDAL, INSULATION PANELS WITH STEEL OR ALUMINIUM FASCIA’S FOR WALLS, ROOFING AND CLADDING
PAGE
26-44
26-31
32-33
34-44
E & O E
5
ICON KEY
TIMBER
CONCRETE
STEEL
BRICK
WARM ROOF AND DEEP INSULATION SYSTEMS
SOFFIT INSULATION RETENTION
GLASS AND MINERAL WOOL INSULATION SYSTEMS
EXTERNAL WALL INSULATION (EWI) SYSTEMS
HOW TO USE THIS GUIDE
6 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
Self Drilling Insulation - Phillips/Torx
INSULATION FIXINGS
Designed For: Fixing insulation to steel and timber purlins
Head Style: Phillips 2/Torx 25
Drive: Single
Thread Form: AISI C1022
Material Grade: 500hr Evoshield®
Coating: Steel drillingcapacity 0.7-2.0 mm
Recommended Drill Speed:
1,500 - 2,500 RPM
Product Range
IS60 4.8 x 60mm 200IS80 4.8 x 80mm 200IS100 4.8 x 100mm 200IS110 4.8 x 110mm 200IS120 4.8 x 120mm 200IS130 4.8 x 130mm 200IS140 4.8 x 140mm 200IS150 4.8 x 150mm 200IS160 4.8 x 160mm 200IS170 4.8 x 170mm 200IS180 4.8 x 180mm 200IS190 4.8 x 190mm 100IS200 4.8 x 200mm 100IS220 4.8 x 220mm 100IS240 4.8 x 240mm 100IS260 4.8 x 260mm 100IS280 4.8 x 280mm 100IS300 4.8 x 300mm 100
CODE SIZE BOX
Technical Data
Diameter Surface Hardness Core Hardness
4.8mm 611.7HV 492.0HV
Hardness Rating (Vickers scale)
Diameter Tensile Strength Shear Strength
4.8mm 11.23kN 7.7kN
Ultimate Mechanical Performance
Diameter Drill point
4.8mm Tek 2
Ultimate pull out values
0.6mm 1.2mm 2.5mm
0.85kN 2.25kN 5.38kN
Steel Thickness
Diameter Drill point
4.8mm Tek 2
Ultimate pull out values (C16 grade timber)
25.0mm 35.0mm
1.90kN 4.00kN
Embedment depth
T25IS120 4.8 x 120mm 200T25IS140 4.8 x 140mm 200T25IS160 4.8 x 160mm 200T25IS180 4.8 x 180mm 200T25IS200 4.8 x 200mm 100
Phillips
Torx
Fixing Finder Pages - 28,29,32
[email protected] www.evolutionfasteners.co.uk
INSULATION FIXINGS
CODE SIZE BOX
Self-Drilling Insulation Screws Bi-metal – A4 Stainless Steel
Designed For: Fixing insulation to light gauge steel or timber substrates. Also suitable where dissimilar metals are being used or superior corrosion resistance is required
Head Style: Philips No. 2/ Bugle Head
Thread Form: Coarse thread (Pitch = 1.8mm (ap-prox.)
Material Grade:
SAE C1022 Carbon Steel – Drilling point AISI 316/ EN 1.4401 (A4) Stainless Steel – shank and head
Coating: 5µm electroplated Zinc.
Recommended Drill Speed:
Steel drilling capacity 0.7-2.0 mm 1,500 - 2,500 RPM z
Technical Data
Product Range
A4IS45 4.8 x 45mm 100A4IS60 4.8 x 60mm 100A4IS80 4.8 x 80mm 100
A4IS100 4.8 x 100mm 100A4IS120 4.8 x 120mm 100A4IS140 4.8 x 140mm 100A4IS160 4.8 x 160mm 100A4IS180 4.8 x 180mm 100A4IS200 4.8 x 200mm 100A4IS240 4.8 x 240mm 100
CODE SIZE BOX
Diameter Surface Hardness Core Hardness
4.8mm 492.8HV 482.3HV
Hardness Rating (Vickers scale)
DiameterTensile
Strength Shear
Strength
4.8mm 7.90kN 5.41kN
Ultimate Mechanical Performance
Diameter Drill point
4.8mm Tek 2
Ultimate pull out values
0.6mm 1.2mm 2.5mm
0.78kN 2.07kN 4.71kN
Steel Thickness
Diameter Drill point
4.8mm Tek 2
Ultimate pull out values (timber)
25.0mm 35.0mm
1.76kN 3.83kN
Embedment depth
1
2
3
Fixing Finder Pages - 30,31,33
8 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
Insulation AnchorsGalvanised Insulation Anchors / A2 Stainless Steel Insulation Anchors
INSULATION FIXINGS
Designed For: Fixing rigid insulationboards and mineral wool insulation to blockwork, brickwork or concrete substratesin C1 and C2 internal corrosion environments
Head Style: 40mm ØD compression disk
Material Grade: SAE 1080 spring steel (non-hardened)/AISI 304 / EN 1.4301/ A2-70 stainless steel
Coating: HD Galvanised - Z140 (pursuant to EN 10346)/None
Fire Classification:
A1 (pursuant to EN 13501-1)
GIA 880 80mm 50GIA 890 90mm 50GIA 8110 110mm 50GIA 8140 140mm 50GIA 8170 170mm 50GIA 8200 200mm 50GIA 8240 240mm 50
CODE SIZE BOX
Productcode
NominalDiameter
(mm)
35.00 40.00 45.00
GIA80 08.00 0.7kN 0.7kN 1.0kNGIA90 08.00 0.7kN 0.7kN 1.0kNGIA110 08.00 0.7kN 0.7kN 1.0kNGIA140 08.00 0.7kN 0.7kN 1.0kNGIA170 08.00 0.7kN 0.7kN 1.0kNGIA240 08.00 0.7kN 0.7kN 1.0kN
A2GIA110 08.00 0.7kN 0.8kN 1.0kN
A2GIA140 08.00 0.7kN 0.8kN 1.0kN
A2GIA170 08.00 0.7kN 0.8kN 1.0kN
Pull Out DataEmbedment Depth (Mm)
Product Range
Technical Data
Fixing Finder Pages - 28 - 33
A2GIA110 110mm 50A2GIA140 140mm 50A2GIA170 170mm 50
A2 Stainless Steel
Galvanised
[email protected] www.evolutionfasteners.co.uk
INSULATION FIXINGS
GIA 880 80mm 50GIA 890 90mm 50GIA 8110 110mm 50GIA 8140 140mm 50GIA 8170 170mm 50GIA 8200 200mm 50GIA 8240 240mm 50
CODE SIZE BOX
Heavy Duty Roofing Screw
Designed For: Fixing insulation and single ply membrane to plywood, timbers, steel decking and concrete. *
Head Style: Dome Head (Pan)
Drive: PH3
Thread Form: Coarse single thread
Material Grade: AISI C1022
Coating: 500hr Evoshield®
Technical Data
Diameter Surface Hardness Core Hardness
5.5mm 581.1 HVO.3 438.8 HVO.3
Hardness Rating (Vickers scale)
Diameter Tensile Strength Shear Strength
6.3mm 18.6kN 7.3kN
Ultimate Mechanical Performance
0.6 1.2 25.0 35.0 25.0 35.0
2.4kN 4.3kN 8.7kN 13.9kN 7.1kN 10.5kN
Steel Concrete (C35) Timber (C16)
Thickness (mm) Embedment (mm)
Substrate
Ultimate pull out values (unfactored)
ERS76 76 mm 100ERS100 100 mm 100ERS127 127 mm 100ERS152 152 mm 100ERS176 176 mm 50ERS200 200 mm 50ERS225 225 mm 50ERS250 250 mm 50
CODE SIZE BOX
Product Range
HEAVY DUTY, MULTI-PURPOSEROOFING SCREW
CALL TO PLACE ORDERT: +44 (0)141 647 7100
10 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
Composite Panel - TEK® 3 – 16mm/19mm Washer1.2mm - 3.5mm Steel Thickness
Designed For - Fixing cladding and roofing applications to hot and cold rolled purlins/rails Fastening liner panels and general components to steel
Head Style - Hexagonal
Drive - 5/16” hexagonal
Washer - 16mm/ 19mm Ø bonded EPDM
Thread Form - Coarse thread (Tek 3)
Shank Material - Carbon steel
Material Grade - SAE C1022
Coating - 500Hr EvoShield®
Product Range
TSBWHT5.5-80-3 5.5 x 80mm 100 16mm
TSBWHT5.5-105-3 5.5 x 105mm 100 16mmTSBWHT5.5-115-3 5.5 x 115mm 100 16mm
TSBWHT5.5-135-3 5.5 x 135mm 100 16mmTSBWHT5.5-150-3 5.5 x 150mm 100 16mm
TSBWHT16-5.5-185-3 5.5 x 185mm 100 16mm
CODE SIZE BOX WASHER SIZE
TSBWHT19-5.5-80-3 5.5 x 80mm 100 19mm
TSBWHT19-5.5-105-3 5.5 x 105mm 100 19mm
TSBWHT19-5.5-135-3 5.5 x 135mm 100 19mm
TSBWHT19-5.5-150-3 5.5 x 150mm 100 19mmTSBWHT19-5.5-185-3 5.5 x 185mm 50 19mmTSBWHT19-5.5-225-3 5.5 x 225mm 50 19mmTSBWHT19-5.5-240-3 5.5 x 240mm 50 19mmTSBWHT19-5.5-275-3 5.5 x 275mm 50 19mmTSBWHT19-5.5-300-3 5.5 x 300mm 50 19mm
Ultimate pull out values
Diameter Drill point
5.5mm Tek 3
1.2mm 1.6mm 2.0mm 2.5mm 3.0mm 4.0mm
1.7kN 2.1kN 2.7kN 4.6kN 4.8kN 5.5kN
Steel Thickness
Diameter Surface Hardness Core Hardness
5.5mm 550.0HV 465.0HV
Hardness Rating (Vickers scale)
DiameterTensile
Strength Shear Strength
5.5mm 16.5kN 10.3kN
Unfactored Mechanical Performance
DiameterIn 0.6mm
steelIn 1.2mm
steel5.5mm 3.1kN 6.0kN
Pullover Performance
Technical Data
Fixing Finder Pages - 35 - 39
TSBWHT6.3-80-GP 6.3 X 80mm 100TSBWHT6.3-100-GP 6.3 X 100mm 100TSBWHT6.3-125-GP 6.3 X 125mm 100TSBWHT6.3-150-GP 6.3 X 150mm 100
CODE SIZE BOX
Composite Panel for Timber
19mm washer
16mm washer
INSULATION FIXINGS
[email protected] www.evolutionfasteners.co.uk
A2/A4 Stainless Steel Bi-metal Composite Panel1.2mm - 3.5mm Steel Thickness
Designed For - Use in brick-tie channel systems and for fastening aluminium sheeting and panels
Head Style - Hexagonal
Drive - 5/16” hexagonal
Washer - 16mm Ø bonded EPDM
Thread Form - Coarse thread
Shank Material - Stainless steel
Material Grade - AISI 304/ EN 1.4301
Coating - (A2) or AISI 316/ EN 1.4401 (A4) Electroplated zinc
Product Range
CODE SIZE BOX WASHER SIZE
Tek 3 range – unfactored pull out values
Diameter Drill point
5.5mm Tek 3
1.2mm 1.6mm 2.0mm 2.5mm 3.0mm 4.0mm
1.7kN 2.1kN 2.5kN 3.3kN 4.1kN 5.4kN
Steel Thickness
Diameter Surface Hardness Core Hardness
5.5mm 465.6 HV0.3 323.7 HV0.3
Hardness Rating (Vickers scale)
DiameterIn 0.6mm
steelIn 1.2mm
steel5.5mm 2.4kN 8.1kN
Pullover Performance
Technical Data
BMTSBWHT5.5-105-5 5.5 x 105mm 100 16mmBMTSBWHT5.5-125-5 5.5 x 125mm 100 16mm
BMTSBWHT5.5-150-5 5.5 x 150mm 100 19mmBMTSBWHT5.5-185-5 5.5 x 185mm 50 19mmBMTSBWHT5.5-245-5 5.5 x 245mm 50 19mm
Tek 5 range – unfactored pull out values
Diameter Drill point
5.5mm Tek 5
4mm 5mm 6mm 8mm 10mm 12.5mm
6.4kN 7.7kN 10.1kN 11.4kN 12.3kN 12.8kN
Steel Thickness
Fixing Finder Pages - 40 - 44
BMHT12-5.5-105-3 5.5 x 105mm 100 12mmBMHT12-5.5-135-3 5.5 x 135mm 100 12mmBMHT12-5.5-150-3 5.5 x 150mm 100 12mmBMHT12-5.5-185-3 5.5 x 185mm 100 12mm
BMTSBWHT5.5-185-3 5.5 x 185mm 50 19mmBMTSBWHT5.5-235-3 5.5 x 235mm 50 19mmBMTSBWHT5.5-275-3 5.5 x 275mm 50 19mm
BMTSBWHT5.5-80-3 5.5 x 80mm 100 16mmBMTSBWHT5.5-105-3 5.5 x 105mm 100 16mmBMTSBWHT5.5-135-3 5.5 x 135mm 100 16mm
BMTSBWHT5.5-150-3 5.5 x 150mm 100 16mmBMTSBWHT5.5-165-3 5.5 x 165mm 100 16mm
BMTSBWHT16-5.5-185-3 5.5 x 185mm 50 16mm
A4BMHT105-3 5.5 x 105mm 100 16mmA4BMHT135-3 5.5 x 135mm 100 16mm
A4BMHT150-3 5.5 x 150mm 100 16mm
A4BMHT185-3 5.5 x 185mm 100 19mm
A2 Heavy Section Bi-Metal
A4
A2
INSULATION FIXINGS
12 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
A4 Bi-Metal Stainless Steel Masonry Screw
Designed For: Fixing timber battens,trunking, track and generalcomponents into concrete, masonry and timber
Head Style: 5/16” hexagonal head/Countersunk
Shank Material: Stainless Steel
Material Grade: AISI 316/ A4
Technical Data
Product Range
CODE SIZE BOX QUANTITY
Diameter SurfaceHardness
CoreHardness
6.3mm 577.4 HV0.3 465.1 HV0.3
Hardness Rating (Vickers scale)
Diameter TensileStrength
ShearStrength
6.3mm 18.7kN 8.9kN
Unfactored Mechanial Performance
Major diameter Steel thickness Steel thickness Steel thickness
6.3mm 0.7mm 1.0mm 1.2mm
Force 1.0kN 1.4kN 2.0kN
Steel substrate (S275 JR mild steel)
Major diameter Timber grade Embedment depth
Load
6.3mm C16 25.0mm 2.3kN
6.3mm C16 35.0mm 3.7kN
Ultimate pull out loading from timber
Ultimate pull out loading from steel
1
2
3
INSULATION FIXINGS
Fixing Finder Pages - 30,33
A4CSK6.3-45-GP 6.3mm x 45mm 100A4CSK6.3-57-GP 6.3mm x 57mm 100A4CSK6.3-75-GP 6.3mm x 75mm 100
A4HH6.3-32-GP 6.3mm x 32mm 100
A4HH6.3-45-GP 6.3mm x 45mm 100A4HH6.3-57-GP 6.3mm x 57mm 100A4HH6.3-70-GP 6.3mm x 70mm 100A4HH6.3-82-GP 6.3mm x 82mm 100A4HH6.3-100-GP 6.3mm x 100mm 100A4HH6.3-125-GP 6.3mm x 125mm 100A4HH6.3-140-GP 6.3mm x 140mm 100
Hexagonal Headed
Countersunk Headed
[email protected] www.evolutionfasteners.co.uk
Embedment Depth(mm)
C25/30 Concrete(30N/mm2)
Aerated ConcreteBlock
(7N/mm2)
Class AEngineering Brick
(75 N/mm2)
25.0 2,850 N 650 N 3,69035.0 6,890 N 1,010 N 9,670
Ultimate Loading: Withdrawal Resistance (Concrete and Masonry Substrates)
Characteristic/ Safe Loading: Withdrawal Resistance (Concrete and Masonry Substrates, γ = 3.0)Embedment Depth
(mm)C25/30 Concrete
(30N/mm2)Aerated Concrete
Block(7N/mm2)
Class AEngineering Brick
(75 N/mm2)
25.0 950 N 210 N 1,23035.0 2,290 N 330 N 3,220
Substrate type Category Data
All Nominal embedment depth 35.0mm
Non cracked concrete (>30N/mm2) Minimum base material thicknessMinimum screw spacingMinimum edge distance
100.0mm55.0mm55.0mm
Cracked concrete (>30N/mm2) Minimum base thicknessMinimum screw spacingMinimum edge distance
100.0mm40.0mm55.0mm
Concrete and masonry setting information
Technical Data
C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 ≥C50/60
0.6 1.0 1.0 1.0 1.2 1.2 1.3
0.7 1.0 1.1 1.2 1.3 1.4 1.5
Compressive Strength – Cube (EN 1992)NominalAnchor
Diameter(mm)
DrillHole
Diameter(mm
EmbedmentDepth(mm)
6.3 5.15 25/0
6.3 5.15 35.0
Influence of Compressive Strength on Withdrawal Resistance (Reduction Factors)
Percentageof statedminimum
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Reductionfactor
N/A N/A N/A N/A N/A 0.75 0.80 0.85 0.90 1.00
Influence of edge distance on loadings (reduction factor)
INSULATION FIXINGS
14 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
Self Tapping Masonry Screw
Designed For: Fixing timber battens, trunking, track and general components to concrete andmasonry substrates
Head Style: Countersunk or slotted hexagonal.
Material Grade:
SAE C1022 Carbon steel.
Coating: EvoShield® 500Hr NSST resistant (Aluminium/ Zinc flake bound in resin).
Drive bit: Phillips No. 2 or No.3 female socket, or, 5/16” hexagonal male socket (with slot).
Point: Nail (pyramidal).
INSULATION FIXINGS
Substrate Type
All types
Non-Cracked Concrete(> 20 MPa < 80 MPa)
Cracked Concrete(> 20 MPa < 80 MPa)
Parameter
Nominal Embedment Depth, h1 (mm)
Nominal Drill Hole Diameter, d0 (mm)
Clearance Hole Diameter, df (mm)
Installation Torque, τinst (Nm)
Minimum Member Thickness, hc (mm)
Minimum Edge Distance, cmin (mm)
Minimum Spacing, smin (mm)
Minimum Member Thickness, hmin (mm)
Minimum Edge Distance, cmin (mm)
Minimum Spacing, smin (mm)
4.8 6.3
25 25
4.35 5.15
6 8
< 3.0 < 7.0
100 100
50 55
100 100
50 40
50 55
Screw Nominal Diameter,dnom (mm)
Product Setting Details
1
2
3
MSH
H MSC
SK
[email protected] www.evolutionfasteners.co.uk
MSHH6.3-32-516 6.3 x 32MSHH6.3-45-516 6.3 x 45MSHH6.3-57-516 6.3 x 57MSHH6.3-70-516 6.3 x 70MSHH6.3-82-516 6.3 x 82MSHH6.3-100-516 6.3 x 100MSHH6.3-125-516 6.3 x 125MSHH6.3-140-516 6.3 x 140MSHH6.3-160-516 6.3 x 160MSHH6.3-180-516 6.3 x 180MSHH6.3-200-516 6.3 x 200MSHH6.3-254-516 6.3 x 254
CODE Nominal Dimensions(mm)
Product Range
Min. Thickness, tmin(mm)
Max. Thickness, tmax(mm)
Fixture Limitations
0 70 200 32
30 4545 5755 7575 10080 105
100 125120 145140 165190 215
INSULATION FIXINGS
Screw Nominal Diameter,dnom (mm)
Fixing Finder Pages - 28 - 29
Hexagonal Headed
MSCSK4.8-32-2 4.8 x 32MSCSK4.8-45-2 4.8 x 45MSCSK4.8-57-2 4.8 x 57MSCSK4.8-70-2 4.8 x 70MSCSK4.8-82-2 4.8 x 82MSCSK4.8-100-2 4.8 x 100MSCSK6.3-32-3 6.3 x 32MSCSK6.3-45-3 6.3 x 45MSCSK6.3-57-3 6.3 x 57MSCSK6.3-70-3 6.3 x 70MSCSK6.3-82-3 6.3 x 82MSCSK6.3-100-3 6.3 x 100MSCSK6.3-125-3 6.3 x 125MSCSK6.3-150-3 6.3 x 150
0 70 200 32
30 4545 5755 750 70 200 32
30 4545 5755 7575 100
100 125
Countersunk Headed
16 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
Cementitious Board Screws
Designed For: Fixing cementitious and other dense boards to timber and metal substrates
Head Style: Double countersunk with nibs
Recess type: Phillips No. 2
Thread Type: Patent (pending) Evolution Universal Thread Carbon steel
Material Grade: C1022
Coating: 1,000Hr EvoShield®
Technical Data
Diameter Surface Hardness Core Hardness
4.2mm 553.6HV 414.0HV
Hardness Rating (Vickers scale)
Diameter TensileStrength
ShearStrength
4.2mm 6.9kN 5.0kN
Unfactored Mechanical Performance
Diameter Drill Point
4.2mm Tek 2
Unfactored pull out values (metallic substrate)
1.2mm 1.8mm 2.5mm1.6kN 1.9kN 3.8kN
Steel Thickness
Diameter
4.2mm
Ultimate Pull Out Loads (kN) in C16 Timber
15mm 30mm 50mm1.9 kN 2.7 kN 3.2 kN
Embedment Depth
Product Range
WHX32 4.2 x 32 mm 200
WHX42 4.2 x 42 mm 200
WHX60 4.2 x 60 mm 200
WHX80 4.2 x 80 mm 200
WHX100 4.2 x 100 mm 200
CODE SIZE EVOSHIELD COATING
BOX
WHL08114 4.2 x 32 mm 200
WHL08158 4.2 x 42 mm 200
Bi-metal tip for attaching board to wood stud or metal stud
High and low thread for stable driving
Large wafer head with ribs allows good countersink and clamps the board firmly
INSULATION FIXINGS
Fixing Finder Pages - 28
[email protected] www.evolutionfasteners.co.uk
WHX32 4.2 x 32 mm 200
WHX42 4.2 x 42 mm 200
WHX60 4.2 x 60 mm 200
WHX80 4.2 x 80 mm 200
WHX100 4.2 x 100 mm 200
CODE SIZE EVOSHIELD COATING
BOX
WHL08114 4.2 x 32 mm 200
WHL08158 4.2 x 42 mm 200
Bi-metal tip for attaching board to wood stud or metal stud
Timber Tek
Designed For: Fixing timber or composites to steel
Head Style: Countersunk ot countersunk with nibs
Drive: Phillips® No. 2 or No. 3
Thread Form: Coarse thread (Tek 3)
Shank Material: Carbon steel
Material Grade: SAE C1022
Coating: 500Hr EvoShield®
Technical Data
Tek 3 range – Unfactored pull out values
Diameter Drill point
4.2mm Tek 34.8mm Tek 35.5mm Tek 3
1.2mm 1.6mm 2.0mm 2.5mm 3.0mm 4.0mm
1.0kN 1.2kN 1.9kN 3.5kN 3.9kN 4.8kN1.1kN 1.5kN 2.5kN 3.6kN 3.9kN 4.4kN1.2kN 2.3kN 3.0kN 4.0kN 4.6kN 5.7kN
Steel Thickness
Tek 4 range – Unfactored pull out values
Diameter Drill point
6.3mm Tek 4
2.5mm 3.0mm 4.0mm 5.0mm 6.0mm
4.1kN 4.7kN 5.9kN 6.4kN 7.2kN
Steel Thickness
Tek 5 range – Unfactored pull out values
Diameter Drill point
5.5mm Tek 5
4.0mm 5.0mm 6.0mm 8.0mm 10.0mm 12.5mm
4.2kN 9.8kN 10.4kN 11.7kN 12.5kN 13.8kN
Steel Thickness
Product Range
Wing drill Tek 3 range - for light steelCODE SIZE EFFECTIVE
THREADLENGTH
TSTF4.2-38-3 4.2x38mm 22mm
TSTF4.8-38-3 4/8x38mm 22mmTSTF4.8-45-3 4.8x45mm 27mmTSTF5.5-50-3 5.5x50mm 30mmTSTF5.5-62-3 5.5x62mm 40mmTSTF5.5-80-3 5.5x80mm 60mm
TSTF5.5-100-3 5.5x100mm 80mmTSTF5.5-120-3 5.5x120mm 100mmTSTF5.5-150-3 5.5x150mm 130mmTSTF5.5-180-3 5.5x180mm 155mm
Wing drill Tek 4 range -for medium gauge steel
CODE SIZE EFFECTIVETHREADLENGTH
TSTF6.3-60-4 6.3x60.0mm FULLTSTF6.3-85-4 6.3x85.0mm FULL
Wing drill Tek 5 range - for heavy steel
CODE SIZE EFFECTIVETHREADLENGTH
TSTF5.5-42-5 5.5x42mm 13mmTSTF5.5-65-5 5.5x65mm 28mmTSTF5.5-85-5 5.5x85mm 50mmTSTF5.5-100-5 5.5x100mm 65mmTSTF5.5-110-5 5.5 x 110mm 75mmTSTF5.5-135-5 5.5x135mm 100mmTSTF5.5-150-5 5.5x150mm 115mmTSTF5.5-180-5 5.5x180mm 145mmDiameter Surface
HardnessCore
Hardness4.2mm 582.6HV 477.8HV4.8mm 570.0HV 474.1HV
5.5mm 592.1Hv 478.8HV
6.3mm 587.4 HV0.3
468.9 HV0.3
Hardness Rating (Vickers scale)
Diameter TensileStrength
ShearStrength
4.2mm 10.4kN 5.2kN4.8mm 12.4kN 6.4kN5.5mm 20.1kN 10.3kN6.3mm 22.7kN 15.2kN
Ultimate Mechanical Performance
INSULATION FIXINGS
Fixing Finder Pages - 28,29,32
18 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
Head
Threads
Wings
Point
Winged Reamer
A2 Stainless Bi-Metal Wing-Drill Tek Screw
CODE SIZE EFFECTIVETHREADLENGTH
BMWD4.8-38-3 4.8x38mm 24.0mmBMWD5.5-50-3 5.5x50mm FULLBMWD5.5-62-3 5.5x62mm 40.0mmBMWD5.5-80-3 5.5x80mm 60.0mm
BMWD5.5-100-3 5.5x100mm 60.0mmBMWD5.5-120-3 5.5x120mm 60.0mm
Bi-metal wing drill tek screw range – for light steel
CODE SIZE EFFECTIVETHREADLENGTH
BMWD5.5-65-5 5.5x65mm FULL
BMWD5.5-85-5 5.5x85mm 50.0mmBMWD5.5-110-5 5.5x110mm 50.0mmBMWD5.5-135-5 5.5x135mm 50.0mm
Bi-metal wing drill tek screw range– for heavy steel
Diameter SurfaceHardness
CoreHardness
4.8mm 390.0HV 270.0HV
5.5mm 390.0HV 270.0HV
Hardness Rating (Vickers scale)
Diameter TensileStrength
ShearStrength
4.8mm 9.8kN 8.2kN5.5mm 11.6kN 9.8kN
Ultimate Mechanical Performance
Diameter Substrate-50mm timber
4.8mm 1.6kN5.5mm 3.0kN
Pullover Performance
Tek 3 range – Unfactored pull out values
Diameter Drill point
4.8mm Tek 35.5mm Tek 3
1.2mm 1.6mm 2.0mm 2.5mm 3.0mm 4.0mm
1.9kN 2.7kN 3.5kN 4.5kN 5.0kN 6.3kN
2.0kN 2.4kN 3.6kN 4.3kN 5.1kN 6.7kN
Steel Thickness
Tek 5 range – Unfactored pull out values
Diameter Drill point
5.5mm Tek 5
4.0mm 5.0mm 6.0mm 8.0mm 10.0mm 12.5mm
4.5kN 5.9kN 7.3kN 8.9kN 10.7kN 11.9kN
Steel Thickness
Designed For: Fastening when stainless steel product is required, e.g. in aluminium sheeting and panels
Head Style: Countersunk
Drive: Phillips® No. 2 or No. 3 or Torx® 25
Thread Form: Coarse thread (Tek 3)
Shank Material: Stainless steel
Material Grade: AISI 304/ EN 1.4301 (A2) or AISI 316/ EN 1.4401 (A4)
Recommended Drill Speed:
1,500 - 2,500 RPM
Technical Data
Product Range
Wings ream hole larger than threads so threads will not engage board. Wings break off when they hit steel,
then threads engage to elevate board jacking
INSULATION FIXINGS
Fixing Finder Pages - 30,33
[email protected] www.evolutionfasteners.co.uk
CODE SIZE EFFECTIVETHREADLENGTH
BMWD4.8-38-3 4.8x38mm 24.0mmBMWD5.5-50-3 5.5x50mm FULLBMWD5.5-62-3 5.5x62mm 40.0mmBMWD5.5-80-3 5.5x80mm 60.0mm
BMWD5.5-100-3 5.5x100mm 60.0mmBMWD5.5-120-3 5.5x120mm 60.0mm
CODE SIZE EFFECTIVETHREADLENGTH
BMWD5.5-65-5 5.5x65mm FULL
BMWD5.5-85-5 5.5x85mm 50.0mmBMWD5.5-110-5 5.5x110mm 50.0mmBMWD5.5-135-5 5.5x135mm 50.0mm
Self-drilling Cementitious Board Screw
Designed For: Fixing cementitious and other dense boards to timber and metal substrates
Head Style: Double countersunk with nibs
Drive: Phillips® No. 2
Thread Form: Patent (pending) Evolution Universal Thread
Shank Material: A2 / Carbon Steel
Product Range
BMDW4832 4.8 x 32 mm 200
BMDW4842 4.8 x 42 mm 200
BMDW4850 4.8 x 50 mm 200BMDW4870 4.8 x 70 mm 200
CODE SIZE BOX
Major Diameter
4.8 mm
Ultimate Pull Out Loadings (kN)
0.70 1.00 1.20 1.50 2.00 2.501.10 kN
1.20 kN
1.60 kN
1.80 kN
2.20 kN
3.60 kN
Steel Thickness (mm)Steel Substrates (S275 JR Mild Steel)
Timber SubstratesMajor Diameter
4.8 mm
Timber Grade
Embedment Depth (mm)
Load (kN)
C16 (soft wood)
27.0
35.0
2.60
3.00
Technical Data
Bi-metal tip for attaching board to wood stud or metal stud
High and low thread for stable driving
Large wafer head with ribs allows good countersink and clamps the board firmly
Fixing Finder Pages - 30
20 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
SPR70 Round 70mm 100
SPR90 Round 90mm 100
SP082 Oval 82 x 40mm 100
SSSPR70 A2 Stainless Steel - Round 70mm
100
A2PIW80 Round 80mm 100
CODE SIZE BOX
Stress Plates
Designed For:
Spreading the loading when fixing membrane, insulation and single ply materials in roofing applications, preventing thematerial being fastened from pulling over the head of the fastener.
Galvanised Steel
Stainless Steel
Part Number Form Nominal Thickness
(mm)
Nominal Dimensions (mm)
SPR70 Round 0.7 70.0 (diameter)
SPO82 Oval 0.7 82.0 x 40.0
Stress Plate Nominal Dimensional Information
Fixture Type Substrate Type Companion Product Range
Rigid Insulation/ Single PlyMembrane
Masonry
Thin Metal Purlin (<1.2mm)
Thick Metal Purlin (>1.2mm<3.5mm)
ERS
IS
Stress Plate Companion Fixing Finder
Technical Data
Product Range
Galvanised / Stainless Steel
INSULATION FIXINGS
Fixing Finder Pages - 28 - 33
[email protected] www.evolutionfasteners.co.uk
Insulation Retaining Washers
Designed For: For securing insulation to timber and sheet steel when used with Evolution drywall, IS etc
Technical DataProductcode
NominalHead
Diameter(mm)
NominalBody
Length (mm)
Extensionto FixingLength (mm)
Colour
RW5 46.0 5.0 2.0 White
RW18 46.0 18.0 13.0 Black
RW35 50.0 35.0 20.0 White
RW65 50.0 65.0 50.0 White
RW105 50.0 105.0 80.0 Red
RW165 50.0 165.0 140.0 Red
EVNW35 35.0 N/A N/A Black
EVPPW50 50.0 N/A N/A Black
ECW60 60.0 12.0 10.0 White
ECW90* Used with
ECW60
90.0 N/A N/A P White
Product Range
RW5 5 mm Recess 46 mm 500
RW18 18 mm Recess 46 mm 500
RW65 65 mm Recess 50 mm 400
RW105 105 mm Recess 50 mm 200
RW165 165 mm Recess 50 mm 200
EVNW35 35mm polyprop 35mm 1000
EVPPW50 50mm polyprop 50mm 1000
ECW60 12 mm Recess 60 mm 100
ECW90 Fits ECW60 90 mm 100
CODE SIZE DIAMETER BOX
INSULATION FIXINGS
Fixing Finder Pages - 28 - 31
22 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100
Panel-Fix
INSULATION FIXINGS
Designed For: Quick through-fix for insulation boards into masonry/ aeratedconcrete/ brick/ concrete/ stone
Head Style: Flat
Shank Material: Polypropylene
Material Grade: Thermoplastic Polymer
Colour: White
Insulation Fixing
BOX
EVPF50 8.0 x 50 mm 10.0 - 20.0 mm
EVPF70 8.0 x 70 mm 10.0 - 40.0 mm
EVPF90 8.0 x 90 mm 10.0 - 60.0 mm
EVPF110 8.0 x 110 mm 10.0 - 80.0 mm
EVPF130 8.0 x 130 mm 10.0 - 100.0 mm
CODE SIZE FIXTURE THICKNESS
500
500
500
500
500
Concrete Solid Brick Concrete Block
0.25kN 0.23kN 0.18kN
Ultimate Pull Out Values
50mm
70mm
90mm
110mm
130mm
Technical Data
Product Range
[email protected] www.evolutionfasteners.co.uk
BOX
500
500
500
500
500
OUR NEW BOARD FIXING GUIDE IS ALSO AVILABLE NOW
CALL TO PLACE ORDERT: +44 (0)141 647 7100
To support our various commercial and technical partners, as well as support specifiers and end users of
our products, the Company provides testing services in our captive UKAS
(United Kingdom Accreditation Service) accredited laboratory on system
components or entire system mock-ups for the purposes of
supporting the use of our products in conjunction with such a component or system by empirical S
SPECIFICATIONS AND LABORATORY SERVICES
Where applicable,we will always perform such empirical testing pursuant to tests included on our schedule of accreditation. Where empirical tests fall out with the scope of our schedule of accreditation, we will always apply the provisions of our accredited ISO/ IEC 17025 quality management system to ensure that the results of such testing are validated. Our schedule of accreditation can be viewed on the UKAS website, www.ukas.com.
This service is generally provided on a pro gratis basis, contingent ultimately on the specification and
use of the Companies’ products for the application.
The Company has significantly invested in creating a centre of excellence not only by
purchasing research grade analytical equipment, but also in the creation of
an exceptionally highly skilled multi-disciplinary team of civil, chemical, mechanical and structural engineers. The Company urges readers of this document to make use of our
technical resources as they are generally provided on a pro gratis basis.
SPECIFICATIONS AND LABORATORY SERVICES
The testing and analytical services we offer include, but are not limited to:
-- Mechanical properties of fasteners and systems including tensile strength, compressive strength, material yield strength, shear strength, bending capacity,
torque capacity, surface/ core hardness, depth of case hardening, etc
-- Mechanical interaction properties of fastener assemblies including withdrawal resistance, pry-out resistance, pull-through resistance,
torque behaviour, delamination strength, lap-shearing/ block-tearing resistance, etc,
-- Corrosion resistance properties of fasteners and fastener assemblies including neutral salt
spray resistance, cyclic corrosion resistance, wetting and humidity resistance, coatingthickness measurement, etc,
-- Failure analysis techniques utilising light metallurgical microscopy or SEM
(Scanning Electron Microscope) microscopy, high speed videography, metrology, etc,
-- Chemical composition and PMI (Positive Material Identification)utilising our extensive
spectrometrysuite of XRF (X-Ray Fluorescence), FTIR (Fourier Transform Infrared), UV-Vis (Ultraviolet-visible)
and OES (Optical Emission Spectrometry) spectrometry techniques.
If you want to discuss how we can support you using our extensive laboratory and technical capabilities, contact the Evolution Technical Team for further assistance by e-mail to [email protected] or by telephone call to +44 (0) 141 647 7100.
SPECIFICATIONS AND LABORATORY SERVICES
25
26
FIXING FINDER
PIR, PUR, XPS, EPS, PF AND PE INSULATION BOARDS
PIR
PUR
XPS
PIR boards are the most popular type of rigid insulation boards currently available.
PUR insulation can be injected into wall cavities to create an energy efficient barrier. The foam is able to reach small spaces to create an air-tight seal.
XPS is a closed cell insulation product commonly used in remodeling and new construction applications.
BRANDS
Ballytherm® Kingspan®
Celotex® Quinn Therm®
EcoTherm® Recticel®
Icopal® U-Value Insulated Products®
IKO® Warmline®
BRANDS Dow® Fibran®
BRANDS
Cellecta® Jackson Insulation®
Danosa® Kay-Metzeler®
Dow® Kingspan®
Fibran® Ravatherm®
Jablite® Stylite®
27
EPS
PF
PE
EPS insulation board is high-performing thermal insulation. It upgrades the thermal properties of a building, improving U-values, reducing the risk of water penetration and condensation.
Phenolic foam is considered one of the best material for thermal insulation.
PE exhibits stable thermal properties which save energy and offset pipe freezing over the entire life of a domestic heating system.
BRANDS
Cellecta® Jackson Insulation®
Danosa® Kay-Metzeler®
Dow® Kingspan®
Fibran® Ravatherm®
Jablite® Stylite®
BRANDS
Cellecta® Jackson Insulation®
Danosa® Kay-Metzeler®
Dow® Kingspan®
Fibran® Ravatherm®
Jablite® Stylite®
BRANDS
Cellecta® Jackson Insulation®
Danosa® Kay-Metzeler®
Dow® Kingspan®
Fibran® Ravatherm®
Jablite® Stylite®
PIR, PUR, XPS, EPS, PF AND PE INSULATION BOARDS
28
FIXING FINDER
10 WHX32 PAGE16
TSTF4.8-38-3 PAGE17
TSTF5.5-42-5 PAGE17
WHX42 PAGE16
GIA801 PAGE8
MSHH6.3-45-516 PAGE14
ECW602 PAGE21
SPR703
PAGE20
20 WHX42 PAGE16
TSTF5.5-50-3 PAGE17
TSTF5.5-65-5 PAGE17
IS60 PAGE6
GIA801
PAGE8MSHH6.3-57-516
PAGE14ECW602 PAGE21
SPR703 PAGE20
25 WHX42 PAGE16
TSTF5.5-50-3 PAGE17
TSTF5.5-65-5 PAGE17
IS60 PAGE6
GIA801 PAGE8
MSHH6.3-57-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
30 WHX42 PAGE16
TSTF5.5-50-3 PAGE17
TSTF5.5-65-5 PAGE17
IS60 PAGE6
GIA801 PAGE8
MSHH6.3-57-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
35 IS60 PAGE6
TSTF5.5-62-3 PAGE17
TSTF5.5-85-5 PAGE17
IS60 PAGE6
GIA801 PAGE8
MSHH6.3-70-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
40 IS60 PAGE6
TSTF5.5-62-3 PAGE17
TSTF5.5-85-5 PAGE17
IS60 PAGE6
GIA801 PAGE8
MSHH6.3-70-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
45 IS80 PAGE6
TSTF5.5-80-3 PAGE17
TSTF5.5-85-5 PAGE17
IS80 PAGE6
GIA901 PAGE8
MSHH6.3-82-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
50 IS80 PAGE6
TSTF5.5-80-3 PAGE17
TSTF5.5-85-5 PAGE17
IS80 PAGE6
GIA901 PAGE8
MSHH6.3-82-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
≥ 0.5 ≤ 2.5mm
≥ 1.2 ≤ 4.0mm
≥ 4.0 ≤ 12.0mm
Cold or Hot Rolled Mild Structural Steel (S235 to S480)
Masonry (≥ 7N)
Concrete (≥ C25 ≤ C50)
Non-Fire Rated
A1 Fire Rated
Blockwork, Masonry and Concrete
Washer/ Stress Plate Detail
Kiln Dry Structural
Timber(≥ C16)
Insulation Thickness
(mm)
0mm to 50mm
Fixing Required by Substrate Type
For use in C1, C2 and C3 (internal) corrosivity category applicationsBOARDS BETWEEN
60 IS80PAGE6
TSTF5.5-80-3 PAGE17
TSTF5.5-100-5 PAGE17
IS100 PAGE6
GIA1101 PAGE8
MSHH6.3-100-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
65 IS80 PAGE6
TSTF5.5-100-3 PAGE17
TSTF5.5-110-5 PAGE17
IS100 PAGE6
GIA1101 PAGE8
MSHH6.3-100-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
70 IS80 PAGE6
TSTF5.5-100-3 PAGE17
TSTF5.5-110-5 PAGE17
IS100 PAGE6
GIA1101 PAGE8
MSHH6.3-100-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
75 IS100 PAGE6
TSTF5.5-100-3 PAGE17
TSTF5.5-110-5 PAGE17
IS120 PAGE6
GIA1101 PAGE8
MSHH6.3-100-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
80 IS100 PAGE6
TSTF5.5-120-3 PAGE17
TSTF5.5-110-5 PAGE17
IS120 PAGE6
GIA1401 PAGE8
MSHH6.3-125-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
85 IS100 PAGE6
TSTF5.5-120-3 PAGE17
TSTF5.5-110-5 PAGE17
IS120 PAGE6
GIA1401 PAGE8
MSHH6.3-125-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
90 IS100 PAGE6
TSTF5.5-120-3 PAGE17
TSTF5.5-135-5 PAGE17
IS120 PAGE6
GIA1401 PAGE8
MSHH6.3-125-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
95 IS120 PAGE6
TSTF5.5-120-3 PAGE17
TSTF5.5-135-5 PAGE17
IS140 PAGE6
GIA1401 PAGE8
MSHH6.3-140-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
100 IS120 PAGE6
TSTF5.5-120-3 PAGE17
TSTF5.5-135-5 PAGE17
IS140 PAGE6
GIA1401 PAGE8
MSHH6.3-140-516 PAGE14
ECW602 PAGE21
SPR703 PAGE20
≥ 0.5 ≤ 2.5mm
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
Cold or Hot Rolled Mild Structural Steel (S235 to S480)
Masonry (≥ 7N)
Concrete (≥ C25 ≤ C50)
Non-Fire Rated
A1 Fire Rated
Blockwork, Masonry and Concrete
Washer/ Stress Plate Detail
Kiln Dry Structural
Timber(≥ C16)
Insulation Thickness
(mm)
Fixing Required by Substrate Type
50mm to 100mm For use in C1, C2 and C3 (internal) corrosivity category applications
BOARDS BETWEEN
29
For use in C1, C2 and C3 (internal) corrosivity category applications
NOTE: Telescopic tube washers are available for use in warm roof/ flat roof applications along with a smaller fastener please refer to RW product range (Page 21)
1Diameter can be increased to resist pull-over failure using GIW80 (Page 20), 2Diameter can be increased to resist pull-over failure using ECW90 (Page 21), 3Diameter can be increased to resist pull-over failure using SPR90 (Page 20). 4Diameter can be increased to resist pull-over failure using SSSPR90 (Page 20).
PIR, PUR, XPS, EPS, PF AND PE INSULATION BOARDS
For use in C1, C2 and C3 (internal) corrosivity category applications
100mm to 200mm For use in C1, C2 and C3 (internal) corrosivity category applications
BOARDS BETWEEN
110 IS120 PAGE6
TSTF5.5-150-3 PAGE17
TSTF5.5-150-5 PAGE17
IS140 PAGE6
GIA1701 PAGE8
MSHH6.3-140-516 PAGE14
ECW602 PAGE21
SPR704 PAGE20
120 IS140 PAGE6
TSTF5.5-150-3 PAGE17
TSTF5.5-150-5 PAGE17
IS160 PAGE6
GIA1701 PAGE8
MSHH6.3-160-516 PAGE14
ECW602 PAGE21
SPR704 PAGE20
130 IS140 PAGE6
TSTF5.5-180-3 PAGE17
TSTF5.5-180-5 PAGE17
IS180 PAGE6
GIA1701 PAGE8
MSHH6.3-160-516 PAGE14
ECW602 PAGE21
SPR704 PAGE20
140 IS160 PAGE6
TSTF5.5-180-3 PAGE17
TSTF5.5-180-5 PAGE17
IS180 PAGE6
GIA2001 PAGE8
MSHH6.3-180-516 PAGE14
ECW602 PAGE21
SPR704 PAGE20
150 IS160 PAGE6
TSTF5.5-180-3 PAGE17
TSTF5.5-180-5 PAGE17
IS180 PAGE6
GIA2001 PAGE8
MSHH6.3-180-516 PAGE14
ECW602 PAGE21
SPR704 PAGE20
160 IS180 PAGE6
TSTF5.5-180-3 PAGE17
None IS200 PAGE6
GIA2001 PAGE8
MSHH6.3-200-516 PAGE14
ECW602 PAGE21
SPR704 PAGE20
180 IS200 PAGE6
None None IS220 PAGE6
GIA2401 PAGE8
None ECW602 PAGE21
SPR704 PAGE20
190 IS200 PAGE6
None None IS220 PAGE6
GIA2401 PAGE8
None ECW602 PAGE21
SPR704 PAGE20
200 IS220 PAGE6
None None IS220 PAGE6
GIA2401 PAGE8
None ECW602 PAGE21
SPR704 PAGE20
≥ 0.5 ≤ 2.5mm
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
Cold or Hot Rolled Mild Structural Steel (S235 to S480)
Masonry (≥ 7N)
Concrete (≥ C25 ≤ C50)
Non-Fire Rated
A1 Fire Rated
Blockwork, Masonry and Concrete
Washer/ Stress Plate Detail
Kiln Dry Structural
Timber(≥ C16)
Insulation Thickness
(mm)
Fixing Required by Substrate Type
30
FIXING FINDER
10 BMDW4842 PAGE19
BMDW5.5-50-3 PAGE19
BMDW5.5-65-5 PAGE19
A4IS45 PAGE7
A2GIA801 PAGE8
A4HH6.3-45-516 PAGE12
ECW602
PAGE21SSSPR70 PAGE20
20 BMDW4842 PAGE19
BMDW5.5-50-3 PAGE19
BMDW5.5-65-5 PAGE19
A4IS60 PAGE7
A2GIA801 PAGE8
A4HH6.3-57-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
25 BMDW4842 PAGE19
BMWD5.5-62-3 PAGE18
BMDW5.5-65-5 PAGE19
A4IS60 PAGE7
A2GIA801 PAGE8
A4HH6.3-57-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
30 BMDW4842 PAGE19
BMWD5.5-62-3 PAGE18
BMDW5.5-65-5 PAGE19
A4IS60 PAGE7
A2GIA801 PAGE8
A4HH6.3-57-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
35 A4IS60 PAGE7
BMWD5.5-62-3 PAGE18
BMWD5.5-85-5 PAGE18
A4IS60 PAGE7
A2GIA801 PAGE8
A4HH6.3-70-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
40 A4IS60 PAGE7
BMWD5.5-62-3 PAGE18
BMWD5.5-85-5 PAGE18
A4IS60 PAGE7
A2GIA801 PAGE8
A4HH6.3-70-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
45 A4IS80 PAGE7
BMWD5.5-80-3 PAGE18
BMWD5.5-85-5 PAGE18
A4IS80 PAGE7
A2GIA801 PAGE8
A4HH6.3-82-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
50 A4IS80 PAGE7
BMWD5.5-80-3 PAGE18
BMWD5.5-85-5 PAGE18
A4IS80 PAGE7
A2GIA901 PAGE8
A4HH6.3-82-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
≥ 0.5 ≤ 2.5mm
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
Cold or Hot Rolled Mild Structural Steel (S235 to S480)
Masonry (≥ 7N)
Concrete (≥ C25 ≤ C50)
Non-Fire Rated
A1 Fire Rated
Blockwork, Masonry and Concrete
Washer/ Stress Plate Detail
Kiln Dry Structural
Timber(≥ C16)
Insulation Thickness
(mm)
Fixing Required by Substrate Type
0mm to 50mm For use in C3 and C4 (internal) corrosivity category applicationsBOARDS BETWEEN
50mm to 100mm For use in C3 and C4 (internal) corrosivity category applicationsBOARDS BETWEEN
60 A4IS80 PAGE7
BMWD5.5-80-3 PAGE18
BMWD5.5-110-5 PAGE18
A4IS100 PAGE7
A2GIA1101 PAGE8
A4HH6.3-100-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
65 A4IS80 PAGE7
BMWD5.5-100-3 PAGE18
BMWD5.5-110-5 PAGE18
A4IS100 PAGE7
A2GIA1101 PAGE8
A4HH6.3-100-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
70 A4IS80 PAGE7
BMWD5.5-100-3 PAGE18
BMWD5.5-110-5 PAGE18
A4IS100 PAGE7
A2GIA1101 PAGE8
A4HH6.3-100-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
75 A4IS100 PAGE7
BMWD5.5-100-3 PAGE18
BMWD5.5-110-5 PAGE18
A4IS120 PAGE7
A2GIA1101 PAGE8
A4HH6.3-100-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
80 A4IS100 PAGE7
BMWD5.5-120-3 PAGE18
BMWD5.5-110-5 PAGE18
A4IS120 PAGE7
A2GIA1401 PAGE8
A4HH6.3-125-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
85 A4IS100 PAGE7
BMWD5.5-120-3 PAGE18
BMWD5.5-135-5PAGE18
A4IS120 PAGE7
A2GIA1401 PAGE8
A4HH6.3-125-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
90 A4IS100 PAGE7
BMWD5.5-120-3 PAGE18
BMWD5.5-135-5PAGE18
A4IS120 PAGE7
A2GIA1401 PAGE8
A4HH6.3-125-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
95 A4IS120 PAGE7
BMWD5.5-120-3 PAGE18
BMWD5.5-135-5PAGE18
A4IS140 PAGE7
A2GIA1401 PAGE8
A4HH6.3-140-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
100 A4IS120 PAGE7
BMWD5.5-120-3 PAGE18
BMWD5.5-135-5PAGE18
A4IS140 PAGE7
A2GIA1401 PAGE8
A4HH6.3-140-516 PAGE12
ECW602 PAGE21
SSSPR70 PAGE20
≥ 0.5 ≤ 2.5mm
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
Cold or Hot Rolled Mild Structural Steel (S235 to S480)
Masonry (≥ 7N)
Concrete (≥ C25 ≤ C50)
Non-Fire Rated
A1 Fire Rated
Blockwork, Masonry and Concrete
Washer/ Stress Plate Detail
Kiln Dry Structural
Timber(≥ C16)
Insulation Thickness
(mm)
Fixing Required by Substrate Type
31
NOTE: Telescopic tube washers are available for use in warm roof/ flat roof applications along with a smaller fastener please refer to RW product range (Page 21)
1 Diameter can be increased to resist pull-over failure using A2PIW80 (Page 20), 2 Diameter can be increased to resist pull-over failure using ECW90 (Page 21).
PIR, PUR, XPS, EPS, PF AND PE INSULATION BOARDS
For use in C3 and C4 (internal) corrosivity category applications
For use in C3 and C4 (internal) corrosivity category applications
100mm to 200mm For use in C3 and C4 (internal) corrosivity category applicationsBOARDS BETWEEN
110 A4IS120 PAGE7
None None A4IS140 PAGE7
A2GIA1701
PAGE8A4HH6.3-140-516
PAGE12ECW602 PAGE21
SSSPR70 PAGE20
120 A4IS140 PAGE7
None None A4IS160 PAGE7
A2GIA1701
PAGE8None ECW602
PAGE21SSSPR70 PAGE20
130 A4IS140 PAGE7
None None A4IS180 PAGE7
A2GIA1701
PAGE8None ECW602
PAGE21SSSPR70 PAGE20
140 A4IS160 PAGE7
None None A4IS180 PAGE7
None None ECW602 PAGE21
SSSPR70 PAGE20
150 A4IS160 PAGE7
None None A4IS180 PAGE7
None None ECW602 PAGE21
SSSPR70 PAGE20
160 A4IS180 PAGE7
None None A4IS200 PAGE7
None None ECW602 PAGE21
SSSPR70 PAGE20
180 A4IS180 PAGE7
None None A4IS200 PAGE7
None None ECW602 PAGE21
SSSPR70 PAGE20
190 A4IS200 PAGE7
None None A4IS220 PAGE7
None None ECW602 PAGE21
SSSPR70 PAGE20
200 A4IS200 PAGE7
None None A4IS220 PAGE7
None None ECW602 PAGE21
SSSPR70 PAGE20
≥ 0.5 ≤ 2.5mm
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
Cold or Hot Rolled Mild Structural Steel (S235 to S480)
Masonry (≥ 7N)
Concrete (≥ C25 ≤ C50)
Non-Fire Rated
A1 Fire Rated
Blockwork, Masonry and Concrete
Washer/ Stress Plate Detail
Kiln Dry Structural
Timber(≥ C16)
Insulation Thickness
(mm)
Fixing Required by Substrate Type
32
FIXING FINDER
50 IS80 PAGE6
TSTF5.5-80-3 PAGE17
TSTF5.5-85-5 PAGE17
IS80 PAGE6
GIA901 PAGE8
MSHH6.3-82-516 PAGE14
SPR702 PAGE20
60 IS80 PAGE6
TSTF5.5-80-3 PAGE17
TSTF5.5-100-5 PAGE17
IS100 PAGE6
GIA1101 PAGE8
MSHH6.3-100-516 PAGE14
SPR702 PAGE20
75 IS100 PAGE6
TSTF5.5-100-3 PAGE17
TSTF5.5-110-5 PAGE17
IS120 PAGE6
GIA1101 PAGE8
MSHH6.3-100-516 PAGE14
SPR702 PAGE20
100 IS120 PAGE6
TSTF5.5-120-3 PAGE17
TSTF5.5-135-5 PAGE17
IS140 PAGE6
GIA1401 PAGE8
MSHH6.3-140-516 PAGE14
SPR702 PAGE20
110 IS120 PAGE6
TSTF5.5-150-3 PAGE17
TSTF5.5-150-5 PAGE17
IS140 PAGE6
GIA1701 PAGE8
MSHH6.3-140-516 PAGE14
SPR702 PAGE20
125 IS140 PAGE6
TSTF5.5-180-3 PAGE17
TSTF5.5-180-5 PAGE17
IS180 PAGE6
GIA1701 PAGE8
MSHH6.3-160-516 PAGE14
SPR702 PAGE20
150 IS160 PAGE6
TSTF5.5-180-3 PAGE17
TSTF5.5-180-5 PAGE17
IS180 PAGE6
GIA2001 PAGE8
MSHH6.3-180-516 PAGE14
SPR702 PAGE20
180 IS200 PAGE6
None None IS220 PAGE6
GIA2401 PAGE8
None SPR702 PAGE20
190 IS200 PAGE6
None None IS220 PAGE6
GIA2401 PAGE8
None SPR702 PAGE20
200 IS220 PAGE6
None None IS240 PAGE6
GIA2401 PAGE8
None SPR702 PAGE20
≥ 0.5 ≤ 2.5mm
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
Cold or Hot Rolled Mild Structural Steel (S235 to S480)
Masonry (≥ 7N)
Concrete (≥ C25 ≤ C50)
Blockwork, Masonry and Concrete Washer/ Stress Plate
Detail
Kiln Dry Structural
Timber(≥ C16)
Insulation Thickness
(mm)
Fixing Required by Substrate Type
For use in C1, C2 and C3 (internal) corrosivity category applications
GLASS
ROCKRock wool has excellent sound-deadening properties and higher insulating value than fiberglass.
Glass wool insulation, also known as fibreglass, is made from glass fibres. Glass is heated to very high temperatures until it melts, andis then spun quickly to create fibres.
GLASS, ROCK, STONE AND MINERAL WOOL ROLLS, BATTENS, MATTRESSES AND BOARDS
33
1 Diameter can be increased to resist pull-over failure using GIW80 (Page 20),
2 Diameter can be increased to resist pull-over failure using SPR90 (Page 20).
50 A4IS80 PAGE7
BMWD5.5-80-3 PAGE18
BMWD5.5-85-5 PAGE18
A4IS80 PAGE7
A2GIA903 PAGE8
A4HH6.3-82-516 PAGE12
SSSPR70PAGE20
60 A4IS80 PAGE7
BMWD5.5-80-3 PAGE18
BMWD5.5-110-5 PAGE18
A4IS100 PAGE7
A2GIA1103
PAGE8A4HH6.3-100-516
PAGE12SSSPR70PAGE20
75 A4IS100 PAGE7
BMWD5.5-100-3 PAGE18
BMWD5.5-110-5 PAGE18
A4IS120 PAGE7
A2GIA1103
PAGE8A4HH6.3-100-516
PAGE12SSSPR70PAGE20
100 A4IS120 PAGE7
BMWD5.5-120-3 PAGE18
BMWD5.5-135-5 PAGE18
A4IS140 PAGE7
A2GIA1403
PAGE8A4HH6.3-140-516
PAGE12SSSPR70PAGE20
110 A4IS120 PAGE7
None None A4IS140 PAGE7
A2GIA1703 PAGE8
A4HH6.3-140-516 PAGE12
SSSPR70PAGE20
125 A4IS140 PAGE7
None None A4IS180 PAGE7
A2GIA1703 PAGE8
None SSSPR70PAGE20
150 A4IS160 PAGE7
None None A4IS180 PAGE7
None None SSSPR70PAGE20
180 A4IS180 PAGE7
None None A4IS200 PAGE7
None None SSSPR70PAGE20
190 A4IS200 PAGE7
None None A4IS220 PAGE7
None None SSSPR70PAGE20
200 A4IS200 PAGE7
None None A4IS220 PAGE7
None None SSSPR70PAGE20
≥ 0.5 ≤ 2.5mm
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
Cold or Hot Rolled Mild Structural Steel (S235 to S480)
Masonry (≥ 7N)
Concrete (≥ C25 ≤ C50)
Blockwork, Masonry and Concrete Washer/ Stress
Plate Detail
Kiln Dry Structural
Timber(≥ C16)
Insulation Thickness
(mm)
Fixing Required by Substrate Type
NOTE: Telescopic tube washers are available for use in warm roof/ flat roof applications along with a smaller fastener please refer to RW product range (Page 21)
3 Diameter can be increased to resist pull-over failure using A2PIW80 (Page 20).
GLASS, ROCK, STONE AND MINERAL WOOL ROLLS
Rock wool has excellent sound-deadening properties and higher insulating value than fiberglass.
For use in C3 and C4 (internal) corrosivity category applications
STONE
MINERAL
Stone wool delivers unique benefits as an insulation solution and effectively reduces airflow and sound transmission, while providing higher airflow resistivity for improved sound attenuation.
Mineral Wool insulation products are designed and produced to ensure healthy, safe and environmentally-friendly places to live and work.
Glass wool insulation, also known as fibreglass, is made from glass fibres. Glass is heated to very high temperatures until it melts, andis then spun quickly to create fibres.
34
FIXING FINDER
FIXING STRUCTURAL, TRAPEZOIDAL, INSULATION PANELS WITH STEEL OR ALUMINIUM FASCIA’S FOR WALLS, ROOFING AND CLADDING
IN THIS SECTION, THE 3 MOST POPULAR BRANDS FOR TRAPEZOIDAL INSULATION ARE SPLIT INTO TWO SECTIONS:
EVOSHIELD® C1, C2 AND C3 CORROSIVITY ENVIRONMENTS
AND
A2 STEEL STAINLESS FOR C3 AND C4 CORROSIVITY ENVIRONMENTS
35
40 TSBWHT5.5-80-3 PAGE10
TSBWHT5.5-85-5 PAGE10
TSBWHT6.3-80-GPPAGE10
53 TSBWHT5.5-80-3 PAGE10
TSBWHT5.5-105-5 PAGE10
TSBWHT6.3-100-GPPAGE10
60 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-105-5 PAGE10
TSBWHT6.3-100-GPPAGE10
73 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
80 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
91 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
100 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
115 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
TSBWHT6.3-150-GPPAGE10
120 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
137 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
150 TSBWHT5.5-185-3 PAGE10
TSBWHT+5.5-235-5 PAGE10
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCORE
Thickness(mm)
CORE (TROUGH) FIXINGS
Steel Substrates Timber Substrate(≥ C16)
Composite Panel Fasteners for Kingspan KS1000RW & KS2000RW Type Panels
KINGSPAN® INSULATED PANELS
EvoShield® For use in C1, C2 and C3(internal) corrosivity category applications
TRAPEZOIDAL PANELS IN C1,C2 AND C3
36
FIXING FINDER
71 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
84 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
91 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
104 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
111 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
TSBWHT6.3-150-GPPAGE10
122 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
131 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
146 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
151 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
168 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
181 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCROWN
Thickness(mm)
CROWN (PEAK) FIXINGS
Steel Substrates Timber Substrate(≥ C16)
Composite Panel Fasteners for Kingspan® KS1000TS® Type Panels
40 TSBWHT5.5-80-3 PAGE10
TSBWHT5.5-85-5 PAGE10 TSBWHT6.3-80-GPPAGE10
50 TSBWHT5.5-80-3 PAGE10
TSBWHT5.5-105-5 PAGE10
TSBWHT6.3-100-GPPAGE10
60 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-105-5 PAGE10
TSBWHT6.3-100-GPPAGE10
70 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
80 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
100 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
115 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
TSBWHT6.3-150-GPPAGE10
120 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
137 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
150 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCORE
Thickness(mm)
CORE (TROUGH) FIXINGS
Steel Substrates Timber Substrate(≥ C16)
37
TRAPEZOIDAL PANELS IN C1,C2 AND C3
71 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
81 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
91 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
101 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
111 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
TSBWHT6.3-150-GPPAGE10
131 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
146 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
151 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
168 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
181 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCROWN
Thickness(mm)
CROWN (PEAK) FIXINGS
Steel Substrates Timber Substrate(≥ C16)
Composite Panel Fasteners for Kingspan® KS1000AWP® Type Panels
45 TSBWHT5.5-80-3 PAGE10
TSBWHT5.5-85-5 PAGE10
TSBWHT6.3-80-GPPAGE10
50 TSBWHT5.5-80-3 PAGE10
TSBWHT5.5-105-5 PAGE10
TSBWHT6.3-100-GPPAGE10
60 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-105-5 PAGE10
TSBWHT6.3-100-GPPAGE10
70 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
80 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
100 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
120 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
140 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
150 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCORE
Thickness(mm)
TONGUE FIXINGS
Steel Substrates Timber Substrate(≥ C16)
38
FIXING FINDER
Composite Panel Fasteners for Eurobond® Europanel® Type Panels
75 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
100 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
125 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
150 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
175 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
200 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
240 TSBWHT5.5-275-3 PAGE10
None None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCORE
Thickness(mm) Steel Substrates Timber Substrate
(≥ C16)
EUROBOND INSULATED PANELS
75 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
100 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
125 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
150 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
175 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
200 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
240 TSBWHT5.5-275-3 PAGE10
None None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCORE
Thickness(mm) Steel Substrates Timber Substrate
(≥ C16)
Composite Panel Fasteners for Eurobond® Rockspan® & Rainspan® Type Panels
39
TRAPEZOIDAL PANELS IN C1,C2 AND C3
Composite Panel Fasteners for TATA® Trisomet® Type Panels
40 TSBWHT5.5-80-3 PAGE10
TSBWHT5.5-85-5 PAGE10
TSBWHT6.3-80-GPPAGE10
60 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-105-5 PAGE10
TSBWHT6.3-100-GPPAGE10
80 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
100 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
120 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
135 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCORE
Thickness(mm) Steel Substrates Timber Substrate
(≥ C16)
TATA INSULATED PANELS
72 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
92 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
112 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
TSBWHT6.3-150-GPPAGE10
132 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
152 TSBWHT5.5-185-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
167 TSBWHT5.5-225-3 PAGE10
TSBWHT5.5-235-5 PAGE10
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulationCROWN
Thickness(mm)
CROWN (PEAK) FIXINGS
Steel Substrates Timber Substrate(≥ C16)
CORE (TROUGH) FIXINGS
Composite Panel Fasteners for TATA® Trimapanel® Type Panels
70 TSBWHT5.5-105-3 PAGE10
TSBWHT5.5-125-5 PAGE10
TSBWHT6.3-120-GPPAGE10
90 TSBWHT5.5-135-3 PAGE10
TSBWHT5.5-150-5 PAGE10
TSBWHT6.3-150-GPPAGE10
120 TSBWHT5.5-150-3 PAGE10
TSBWHT5.5-185-5 PAGE10
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
EvoShield® for C1, C2 and C3 (internal) Corrosivity EnvironmentsInsulation Thickness
(mm)Steel Substrates Timber Substrate
(≥ C16)
40
FIXING FINDER
40 BMTSBWHT5.5-80-3 PAGE11
BMTSBWHT5.5-85-5 PAGE11
None
53 BMTSBWHT5.5-80-3 PAGE11
BMTSBWHT5.5-105-5 PAGE11
None
60 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-105-5 PAGE11
None
73 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
80 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
91 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
100 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
115 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
120 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
137 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
150 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentsInsulationCORE
Thickness(mm)
CORE (TROUGH) FIXINGS
Steel Substrates Timber Substrate(≥ C16)
Composite Panel Fasteners for Kingspan KS1000RW & KS2000RW Type Panels
KINGSPAN® INSULATED PANELS
For use in C3 and C4 (internal) corrosivity category applications
41
For use in C3 and C4 (internal) corrosivity category applications
TRAPEZOIDAL PANELS IN C3 AND C4
71 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
81 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
91 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
104 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
111 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
122 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
131 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
146 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
151 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-235-5 PAGE11
None
168 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-235-5 PAGE11
None
181 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-235-5 PAGE11
None
≥ 4.0 ≤ 12.0 mm ≥ 1.2 ≤ 4.0 mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentsInsulationCROWN
Thickness(mm)
CROWN (PEAK) FIXINGS
Steel Substrates Timber Substrate
≥ 4.0 ≤ 12.0 mm
Composite Panel Fasteners for Kingspan® KS1000TS® Type Panels
40 BMTSBWHT5.5-80-3 PAGE11
BMTSBWHT5.5-85-5 PAGE11
None
50 BMTSBWHT5.5-80-3 PAGE11
BMTSBWHT5.5-105-5 PAGE11
None
60 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-105-5 PAGE11
None
70 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
80 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
100 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
115 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
120 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
137 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
150 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentsInsulationCORE
Thickness(mm)
CORE (TROUGH) FIXINGS
Steel Substrates Timber Substrate(≥ C16)
42
FIXING FINDER
71 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
81 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
91 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
101 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
111 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
131 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
146 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
151 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
168 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
181 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
≥ 4.0 ≤ 12.0 mm ≥ 1.2 ≤ 4.0 mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentsInsulationCROWN
Thickness(mm)
CROWN (PEAK) FIXINGS
Steel Substrates Timber Substrate
≥ 4.0 ≤ 12.0 mm
Composite Panel Fasteners for Kingspan® KS1000AWP® Type Panels
45 BMTSBWHT5.5-80-3 PAGE11
BMTSBWHT5.5-85-5 PAGE11
None
50 BMTSBWHT5.5-80-3 PAGE11
BMTSBWHT5.5-105-5 PAGE11
None
60 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-105-5 PAGE11
None
70 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
80 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
100 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
120 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
140 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
150 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentsInsulationCORE
Thickness(mm)
TONGUE FIXINGS
Steel Substrates Timber Substrate(≥ C16)
43
Composite Panel Fasteners for Eurobond® Europanel® Type Panels
EUROBOND INSULATED PANELS
75 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
100 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
125 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
150 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
175 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
200 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
240 BMTSBWHT5.5-275-3 PAGE11
None None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentssInsulationCORE
Thickness(mm) Steel Substrates Timber Substrate
(≥ C16)
Composite Panel Fasteners for Eurobond® Rockspan® & Rainspan® Type Panels
75 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
100 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
125 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
150 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
175 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
200 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-245-5 PAGE11
None
240 BMTSBWHT5.5-275-3 PAGE11
None None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
1
A2 Stainless for C3 and C4 Corrosivity EnvironmentssInsulationCORE
Thickness(mm) Steel Substrates Timber Substrate
(≥ C16)
TRAPEZOIDAL PANELS IN C3 AND C4
44
FIXING FINDER
40 BMTSBWHT5.5-80-3 PAGE11
BMTSBWHT5.5-85-5 PAGE11
None
60 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-105-5 PAGE11
None
80 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
100 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
120 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
135 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentsInsulationCORE
Thickness(mm) Steel Substrates Timber Substrate
(≥ C16)
CROWN (PEAK) FIXINGS
CORE (TROUGH) FIXINGS
72 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
92 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
112 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
132 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
152 BMTSBWHT5.5-185-3 PAGE11
BMTSBWHT5.5-235-5 PAGE11
None
167 BMTSBWHT5.5-235-3 PAGE11
BMTSBWHT5.5-235-5 PAGE11
None
≥ 4.0 ≤ 12.0mm ≥ 1.2 ≤ 4.0mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentsInsulationCROWN
Thickness(mm) Steel Substrates Timber Substrate
≥ 4.0 ≤ 12.0 mm
Composite Panel Fasteners for TATA® Trisomet® Type Panels
TATA INSULATED PANELS
Composite Panel Fasteners for TATA® Trimapanel® Type Panels
70 BMTSBWHT5.5-105-3 PAGE11
BMTSBWHT5.5-125-5 PAGE11
None
90 BMTSBWHT5.5-135-3 PAGE11
BMTSBWHT5.5-150-5 PAGE11
None
120 BMTSBWHT5.5-150-3 PAGE11
BMTSBWHT5.5-185-5 PAGE11
None
≥ 1.2 ≤ 4.0mm ≥ 4.0 ≤ 12.0mm
A2 Stainless for C3 and C4 Corrosivity EnvironmentsInsulation Thickness
(mm)Steel Substrates Timber Substrate
(≥ C16)
Visit our websitewww.evolutionfasteners.co.uk for latest product information offers and Evolution news
Sales and Customer Service
Tel: +44 (0) 141 647 7100 Fax: +44 (0) 141 647 5100
INDEX
46
Products
IS
A4IS
GIA/ A2GIA
ERS
TSBWHT
BMTSBWHT
A4HH
MSHH/MSCSK
WHX/WHL
TSTF
BMWD
BMDW
SPR/SSSPR
RW//EVNW/EVPPW/ECW
EVPF
6
7
8
9
10
11
12-13
14-15
16
17
18
19
20
21
22
CODE PAGE
Fixing insulation to steel and timber
Fixing insulation to light gauge steel or timber substrates.
Fixing rigid insulation boards and mineral wool insulation to blockwork, brickwork or concrete substrates
Fixing insulation and single ply membrane to plywood, timbers, steel decking and concrete.
Fixing cladding and roofing applica-tions to hot and cold rolled purlins/rails
Use in brick-tie channel systems and for fastening aluminium sheeting and panelsFixing timber battens,trunking, track and generalcomponents into concrete, masonry and timber
Fixing timber battens, trunking, track and general components to concrete andmasonry substrates
Fixing cementitious and other dense boards to timber and metal substrates
Fixing timber or composites to steel
Fastening when stainless steel product is required
Fixing cementitious and other dense boards to timber and metal substrates
Spreading the loading when fixing membrane, insulation and single ply materials in roofing...
For securing insulation to timber and sheet steel when used with Evolution drywall, IS etc
Quick through-fix for insulation boards into masonry/ aeratedconcrete/ brick/ concrete/ stone
Technical
PAGEINSULATION
47
PIR, PUR, XPS, EPS, PF AND PE INSULATION BOARDS
GLASS, ROCK, STONE AND MINERAL WOOL ROLLS, BATTENS, MATTRESSES AND BOARDS
FIXING STRUCTURAL, TRAPEZOIDAL, INSULATION PANELS WITH STEEL OR ALUMINIUM FASCIA’S FOR WALLS, ROOFING AND CLADDING
26-31
32-33
34-44
This document is wholly authored and published by Evolution Fasteners UK Ltd (herein referred to as “the company” or “Evolution")
This document is intended to be a training tool and educational in nature only. The contents of this document do not constitute any form of warranty or guarantee. The Company provides an industry leading warranty which is detailed in a separate document.
The use of this document does not alleviate, mitigate or otherwise change the legal obligations, or, statutory and regulatory burdens or undertakings of the reader apropos any law, statute, act, regulation, directive, standard, inter alia. This includes, but is not limited to the requirements underthe Building Regulations and/ or the Construction (Design and Management) Regulations, amongst others.
The Company recommends that on every occasion, the reader of this document undertakes their own research and determination as to whether a product or products are suitable for their specific application. Readers of this document are implored to seek the advice of the third parties mentioned in this document on their components and inter-compatibility with other parties’ components.
Where references or citations are made, it is inthe ‘Harvard Style’ pursuant to the guidance laid out by Imperial College London (Imperial College London, 2017).
Unless otherwise noted or referenced: all information, text, illustrations and content herein remain the intellectual property of the Company.
Throughout this document, various third-party logos, brand names and trademarks are used under the fair dealings’ provisions of the Copyright, Designs and Patents Act 1988, herein referred to as “the 1988 Act”, specifically pursuant to Sections 29, 29A and 30 of the 1988 Act.
The use of such logos, brand names or trademarks is not intended toconvey any commercial relationship, or otherwise, between the Company and the third party concerned. The use of such logos, brand names or trademarks is solely intended to benefit and aid the reader in the initial visual recognition of such third party.
ACKNOWLEDGEMENTS, LICENSES, TRADEMARKS AND COPYRIGHT
This document is strictly published and provided without prejudice, without recourse, non-assumptist, errors and omissions excepted, no assured value, no liability and all rights reserved.The use of the UKAS logo and ILAC logo relates only to accredited tests pursuant to our schedule of accreditation, tests out with our schedule are marked “NC”. For the most current version of our schedule please visit www.ukas.com.
GENERAL
1. (a) All orders placed with Evolution Fasteners UK Limited (”the Company”) by the Company’s customer (“the Buyer”) for the sale and the purchase of goods (“the Goods”)are subject to the terms and conditions set out below which shall constitute the contract between the Company and the Buyer (“the Contract”). No modifications or variations to these terms and conditions and no other terms and conditions shall be valid or effective unless expressly accepted in writing by a director of the Company.(b) Any subsequent orders placed with the Company shall be deemed to be placed subject to these terms and conditions unless expressly agreed otherwise in writing by a Director of the Company.
TERMS AND CONDITIONS OF SALE
QUOTATIONS
2. A quotation by the Company does not constitute an offer and the Company reserves the right to withdraw or amend the same at any time prior to the Company’s acceptance of the Buyer’s order. The Buyers purchase order is binding and the Buyer is responsible for
PRICE
3. The price of any goods shall be the Company's list price of the goods prevailing at the date of acceptance of the order by the Company (less any agreed discount).
4. Unless otherwise stated all prices are exclusive of V.A.T.
5. The Company shall be entitled from time to time to vary list price or list prices without prior notice.
PAYMENT
6. Unless otherwise specified in writing by the Company, payment is due on or before the end of the month following that in which the goods were invoiced.
7. Failure by the Buyer to pay for any goods on the due date shall entitle the Company:(a) to cancel the balance (if any) of the contract under which the Buyer has failed to pay for the goods and to recover from the Buyer damages for any loss suffered by the Company as a result of such cancellation, and/or(b) to cancel any other contract or the balance of any other contract which the Company may have with the Buyer and to recover from the Buyer damages for any loss suffered by the Company as a result of such cancellation, and/or(c) to charge the Buyer interest at the rate of 2.5% per month calculated on a day-to-day basis on the amount due from the date of invoice to the date of actual payment thereof (both before and after any judgement) such interest to be paid on demand.
ACCOUNTS
8. The Company reserves the right to close a credit account at any time without prior notice whereupon the whole of the amount outstanding on such account shall become immediately due and payable in full.
COLLECTION AND DELIVERY
9. Where the Company agrees to deliver any goods to the Buyer:
(a) The Buyer shall pay the Company's delivery charges therefore at the rate or rates prevailing at the date of acceptance of the order by the Company or at such other rate or rates as may be agreed between the Company and the Buyer prior to the date of acceptance of the order by the Company.(b) Delivery of the goods shall be made to such place or places as agreed between the Company and the Buyer.(c) The Buyer will ensure that there is adequate access to the place of delivery and that there is made available at the place of delivery adequate labour and other facil-ities in order to enable the goods to be unloaded promptly and safely and the Buyer will indemnify the Company in respect of any losses costs and expenses incurred by the Company as a consequence thereof and (without prejudice to the generality of the foregoing) the Company shall be entitled to charge the Buyer for the storage of the goods whether at the Company's premises or otherwise.(d) If the Buyer shall refuse for any reason whatsoever to accept delivery of the goods the Buyer will indemnify the Company in respect of all losses costs and expenses incurred by the Company as a consequence thereof and (without prejudice to the generality of the foregoing) the Company shall be entitled to charge the Buyer for the storage of the goods whether at the Company's premises or otherwise.(e) The Company shall be entitled to make part deliveries of the goods and for the purposes of these terms and conditions each such part delivery shall be treated as a separate and independent contract for the sale of goods to the Buyer.
10. (a) Any times stated for collection or delivery shall be a bona fide estimate only and whilst the Company will use all reasonable endeavours to meet any such times stated the Company shall not be liable for any delay howsoever caused.(b) Where no times are stated for collection or delivery the Company will use all reasonable endeavours to make the goods available for collection or to deliver the goods (as the case may be) as soon as reasonably practicable.(c) The Company shall be entitled to stop collection by or to withhold delivery to the Buyer of any goods where at the time collection or delivery payment is due to the Company in respect of any goods supplied to the Buyer under any contract whatsoever.
DAMAGE OR LOSS IN TRANSIT
11. Where the Company is responsible for delivering the goods to the Buyer the Company will at its option repair or replace free of charge any goods lost or damaged in transit provided that:
(a) (save in respect of a total loss or non-delivery of the goods) details of any loss or damage have been marked on the copy of the consignment note or delivery documents signed by the Buyer and advised to the Company within 48 hours of delivery and confirmed in writing to the Company with full particulars within 3 days of delivery, and(b) in respect of a total loss or non- delivery of the goods details are advised to the Company in writing (otherwise than on a consignment note or delivery document) with full particulars within (7 days) of the date of the Company's invoice in respect of the goods.
SHORT DELIVERY
12. The Company shall not be responsible for any short delivery unless details thereof are marked on the consignment note or delivery document signed by the Buyer and in the case of loss in transit all the requirements set out in Condition 11(b) above are fulfilled.
STORAGE
13. Where the Company has notified the Buyer that the goods are ready for delivery, the Buyer shall take delivery or arrange for storage. If the Buyer does not so take de-livery or arrange for storage within 7 days of notification the Company shall be entitled to invoice and be paid for the goods as though the goods had been duly delivered in accordance with these instructions and the Company may arrange storage either at the Company’s own premises or elsewhere on the Buyer’s behalf and all charges for storage, insurance and demurrage shall be payable by the Buyer.
DEFECTIVE GOODS
14. The Company shall at their option repair or replace any goods which are defective as to materials or workmanship provided that:
(a) where any alleged defect is discoverable on an inspection of the goods (whether or not the Buyer shall actually inspect the goods) notification of the alleged defect with full particulars thereof is received by the Company in writing within 7 days of the date of collection or delivery of the goods and in any other case notification of the alleged defect is received by the Company in writing with full particulars thereof within 10 days of the date of collection or delivery of the goods, and(b) the Company is notified in writing with full particulars immediately upon discovery of the alleged defect and is afforded the opportunity of inspecting the goods at the premises of the Buyer or if so required by the Company the Buyer immediately returns the goods to the Company's premises carriage paid (but refundable insofar as the goods are repaired or replaced), and(c) any defect is not due to wear and tear neglect abnormal use misuse or improper adjustment.(d) The Company shall not be liable for transportation or installation charges, for expense of the Buyers for repairs or replacements or for damages for delay or loss of use or other indirect, incidental or consequential damage of any kind.
15. (a) As against a person dealing as a consumer as defined by Section 2(3) of the Consumer Rights Act 2015 the following provisions apply. The Company is under a legal duty to supply products that are in conformity with its obligations. The box below contains a summary of the Buyer’s key legal rights in relation to the Goods. Nothing in these terms will affect the Buyer’s legal rights.
Summary of the Buyer’s key legal rights
This is a summary of the Buyer’s key legal rights. These are subject to certain exceptions. For detailed information please visit the Citizens Advice website www.adviceguide.org.uk or call 03454 04 05 06.The Consumer Rights Act 2015 says the Goods must be as described, fit for purpose and of satisfactory quality. During the expected lifespan of the Goods the Buyer’s legal rights entitle the Buyer to the following:
a)Up to 30 days: if the Goods are faulty, then the Buyer can obtain an immediate refund.b) Up to 6 months: if the Goods cannot be repaired or replaced, then the Buyer is entitled to a full refund, in most cases.c) Up to 6 years: if the Goods do not last a reasonable length of time the Buyer may be entitled to some money back.
See also Exercising your right to change your mind (Consumer Contracts Regulations 2013). If the Buyer wishes to exercise its legal rights to reject the Goods the Buyer must ei-ther return them in person, or post them back, to the Company. The Company will pay the costs of postage or collection. Please telephone the Company for a return label or to arrange collection. The provisions contained in this condition 15(a) do not affect the Buyer’s legal rights in relation to faulty or mis-described products
(b)As against a person dealing otherwise than as a consumer as defined by Section 2(3) of the Consumer Rights Act 2015 the provisions contained in Condition 14 above shall be accepted in substitution for and to the entire exclusion of all conditions and warranties and liabilities whatsoever whether express or implied by statute (save those implied by virtue of Section 12 of the Sale of Goods Act 1979) common law usage or otherwise.
16. Save and except as expressly stated in Conditions 14 and 15 above the Company shall not be liable for any defect in the Goods or for any injury or loss resulting from the Goods or any defect therein or from any work done in connection therewith whether such liability is due to the negligence of any servant employee or agent of the Company or otherwise.
17. As against a person dealing otherwise than as a consumer as defined by Section 2(3) of the Consumer Rights Act 2015 in the event that the Company shall be liable to repair or replace the Goods, in no circumstances shall the Company’s liability extend beyond the cost of repair or replacing the Goods. In any event, notwithstanding anything contained in the contract, as against such person in no circumstances shall the Company be liable in contract, tort (including negligence or breach of statutory duty) or otherwise howsoever and whatsoever the cause thereof:
i.For any increased costs or expensesii. For any loss or profit, business contracts, revenues or anticipated savings oriii. For any special direct or consequential damage of any nature whatsoever said to have occurred consequent on the supply or the circumstances of the supply of the Goods.
RETURNED GOODS
18. (a) Where returned Goods are found to be damaged due to the Buyer's fault the Buyer will be liable for the cost of remedying such damage(b) The Company will not accept Goods for credit or rectification unless such return has been pre-authorised by the Company, and the Goods are received by the Com-pany in stock condition, with original packaging and the Company retains the right at its sole discretion whether to accept the return of the Goods or whether to rectify the Goods or whether to issue a credit note in respect thereof.(c) The Buyer shall unless otherwise stated be responsible for the cost of outward and return carriage and insurance of all Goods returned by the Buyer to the Company for rectification or credit which Goods shall be at the risk of the Buyer until actual receipt of the Goods by the Company. The onus of proof of safe delivery shall rest with the Buyer.(d) All Goods returned to the Company by prearrangement and found to contain no fault, will be subject to a 30% restocking charge, providing the Goods are in original stock condition. Any downward variation of this restocking charge shall be at the sole discretion of the Company.(e) No credit shall be allowed for Goods until they have been received complete.
FORCE MAJEURE
19. (a) The Company shall not be responsible for any loss damage delay or non- performance of any contract arising whether directly or indirectly from any cause outside the control of the Company including (but without prejudice to the generality of the foregoing) any cause arising from or attributable to strike lock-out shortage of labour or materials governmental action civil commotion riots wars sabotage storm flood earthquake drought machinery breakdown failure of plant collapse of structures voluntary or mandatory compliance with any direction request or order of any person having or appearing to have authority whether for defence or other governmental or national purposes inability to obtain raw materials equipment fuel power components or transportation.(b) In the event of any delay or non- performance of any contract arising whether directly or indirectly from any cause referred to in Condition 19(a) above the Company shall be entitled to cancel any contract without payment to the Buyer in respect of any loss or damage or otherwise.
TITLE AND RISK
20.1The risk in the Goods shall pass to the Buyer on completion of delivery.
20.2 Title to the Goods shall not pass to the Buyer until the earlier of:(a) the Company receiving payment in full (in cash or cleared funds) for the Goods and any other goods that the Company has supplied to the Buyer, in which case title to the Goods shall pass at the time of payment of all such sums; and(b) the Buyer reselling the Goods, in which case title to the Goods shall pass to the Buyer at the time specified in clause 20.4.
20.3 Until title to the Goods has passed to the Buyer, the Buyer shall:(a) store the Goods separately from all other goods held by the Buyer so that they remain readily identifiable as the Company's property;(b) not remove, deface or obscure any identifying mark or packaging on or relating to the Goods;(c) maintain the Goods in satisfactory condition and keep them insured against all risks for their full price from the date of delivery;(d) notify the Company immediately if it becomes subject to any of the events listed in clause 21; and(e) give the Company such information relating to the Goods as the Company may require from time to time.
20.4 Subject to clause 20.5, the Buyer may resell or use the Goods in the ordinary course of its business (but not otherwise) before the Company receives payment for the Goods. However, if the Buyer resells the Goods before that time:(a) it does so as principal and not as the Company’s agent; and(b) title to the Goods shall pass from the Company to the Buyer immediately before the time at which resale by the Buyer occurs.
20.5 If before title to the Goods passes to the Customer the Customer becomes subject to any of the events listed in clause 21, then, without limiting any other right or remedy the Company may have:(a) the Buyer's right to resell the Goods or use them in the ordinary course of its business ceases immediately; and(b) the Company may at any time:(i) require the Buyer to deliver up all Goods in its possession that have not been resold, or irrevocably incorporated into another product; and(ii) if the Buyer fails to do so promptly, enter any premises of the Buyer or of any third party where the Goods are stored in order to recover them.
20.6 Each and every sub-clause of this clause shall be deemed to be separate from the remainder of the contract and severable accordingly.
TERMINATION
21.1 Without limiting its other rights or remedies, the Company may terminate this Contract with immediate effect by giving written notice to the Buyer if:(a) the Buyer commits a material breach of any term of the Contract and (if such a breach is remediable) fails to remedy that breach within 7 days of that party being notified in writing to do so;(b) the Buyer takes any step or action in connection with its entering administration, provisional liquidation or any composition or arrangement with its creditors (other than in relation to a solvent restructuring), being wound up (whether voluntarily or by order of the court, unless for the purpose of a solvent restructuring), having a receiver appointed to any of its assets or ceasing to carry on business or, if the step or action is taken in another jurisdiction, in connection with any analogous procedure in the relevant jurisdiction;(c) the Buyer suspends, threatens to suspend, ceases or threatens to cease to carry on all or a substantial part of its business; or(d) the Buyer's financial position deteriorates to such an extent that in the Company's opinion the Buyer's capability to adequately fulfil its obligations under the Contract has been placed in jeopardy.
21.2 Without limiting its other rights or remedies, the Company may suspend provision of the Goods under the Contract or any other contract between the Buyer and the Company if the Buyer becomes subject to any of the events listed in clause 21.1(a) to clause 21.1(d), or the Company reasonably believes that the Buyer is about to become subject to any of them, or if the Buyer fails to pay any amount due under this Contract on the due date for payment.
21.3 Without limiting its other rights or remedies, the Company may terminate the Contract with immediate effect by giving written notice to the Buyer if the Buyer fails to pay any amount due under the Contract on the due date for payment.
21.4 On termination of the Contract for any reason the Buyer shall immediately pay to the Company all of the Company's outstanding unpaid invoices and interest.
21.5 Termination of the Contract shall not affect any of the parties' rights and remedies that have accrued as at termination, including the right to claim damages in respect of any breach of this Contract that existed at or before the date of termination.
21.6 Any provision of the Contract that expressly or by implication is intended to come into or continue in force on or after termination shall remain in full force and effect.
GOVERNING LAW AND JURISDICTION
22. The Contract and all contracts between the Company and the Buyer shall in respects be governed by English law and all disputes which may arise out of or in connection with these Conditions or the Contract or any contract between the Company and the Buyer or any Goods supplied or to be supplied under the Contract or any contract shall be subject to the exclusive jurisdiction of the English Courts save that the Company shall be at liberty to bring any legal proceedings against the Buyer in the Courts of any other country which it considers appropriate.23. In the event that the Company shall bring any legal proceedings against the Buyer in connection with these Conditions or the Contract or any contract between the Company and the Buyer or any Goods supplied or to be supplied under the Contract or any contract between the Company and the Buyer the Buyer shall indemnify the Company against all costs and expenses incurred by the Company in connection therewith on a full indemnity basis.
THIRD PARTIES
24. For the avoidance of doubt nothing in these terms and conditions are intended to confer on any third party any benefit or the right to enforce any terms within the conditions.
ACKNOWLEDGEMENTS, LICENSES, TRADEMARKS AND COPYRIGHT
This document is strictly published and provided without prejudice, without recourse, non-assumptist, errors and omissions excepted, no assured value, no liability and all rights reserved.The use of the UKAS logo and ILAC logo relates only to accredited tests pursuant to our schedule of accreditation, tests out with our schedule are marked “NC”. For the most current version of our schedule please visit www.ukas.com.
WW
W.EVO
LUTIO
NFASTEN
ERS.CO.U
K
Visit our website
www.evolutionfasteners.co.ukfor latest product informationoffers and Evolution news
Administration and Accounts
Tel: +44 (0) 20 8905 2759Fax: +44 (0) 20 8207 0044
Sales and Customer Service
Tel: +44 (0) 141 647 7100Fax: +44 (0) 141 647 5100
Email: [email protected]
Copyright 2020 Evolution Fasteners (UK) Ltd. All rights reserved.