Upload
others
View
15
Download
0
Embed Size (px)
Citation preview
Add for Model ITW50 Optional SMD Thermal Tweezer easy and quick reworking of SMD s
as Chip Capacitors & Chip Resistors, SOD Diodes, SOT Transistors and SMD ICs
How it works:1. Switch ON Power and
set desired temperature.2. Grip the chip component
and hold for few seconds till solder melts
3. Pick up chip component.
Variety of SMD Tip inserts to suit different components
Mini SOT SOT 23 DPAK SO 20
• Power Input Supply • Temperature Range •
• Tip to Ground ResistanceTip to Ground Potential •
: 50 Watt: 220VAC, 50Hz: upto 480°C: <2Ω: <2mV
Specifications
• Twin-tube Tip Inserts heat SMD Chip components directly without disturbing adjacent components.
Easy reworking of SMD components • as Chip Resistors/Capacitors/Inductors, MELFs, SODs, SOTs, 4/6/8/14/16/18/20 pin SOIC’s
Features
SMD Chips
RoHSCompliant
L E A D
F R E E
• Power Input Supply• Temperature Range• Temperature Stability• Tip to Ground Potential• Tip to Ground Resistance •
: 90 Watts: 230 VAC, 50 Hz: 80°C ~ 480°C: ±2% of final value : < 2mV: < 2 Ohm
Specifications
• Power & Control Unit• Soldering Pencil Soldering Tip fitted with • Iron Holder with Cleaning Sponge
Scope of Supply
Low Cost High Production Workhorse Soldering Station Model DSS36
Low capital investment + low running cost, uses lower priced Soldering Tips
Rugged 3-digit 7-segment E dL D isplay for SET and
ACTUAL temperatures Displays actual temperature
L Digital DisplayED
The Soldering Station has in-built digital temperature offset provision during calibration to meet ISO9000 requirements. Customer does not need to open the unit and adjust the trim pots.
Temperature Offset for Calibration
Password Protection
The Soldering Station has provision of password locking. After password locking,
operator cannot change the programming parameters
Error Messages
The Soldering Station has self diagnostic feature. It displays the fault of the Soldering Pencil. If the display shows H-E, it means Heating Element is faulty.And if it shows S-E, it meansTemperature Sensor is faulty.
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
shown trademarks are property of their respective owners. Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
reliable & caring since 1976
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected]: 8283820745 & 9316134502
Low Cost High Production Workhorse Soldering Station Model DSS36
Low capital investment + low running cost, uses lower priced Soldering Tips
Useful Tip Inserts for SMD Thermal Tweezer ITW50 for reworking of SMD Chips and SOICs
P/N Size (A) Shape Applicable for
A1388
A1380
A1384
A
A
1.5mm
8mm
20mm
Diagram
SMD Chips
8 Pin SO ICs
20 Pin SO ICs
Wide range of Soldering Tips for different soldering applications
Part Number
960-T-0.8D0.8
Chisel Tip for leadfree soldering
Width A (mm)Description Dimensional DiagramActual Picture
0.517mm
17mm0.5
17mm0.5
17mm0.5
960-T-1.6D1.6
Chisel Tip for leadfree soldering
Chisel Tip for leadfree soldering 960-T-2.4D2.4
Chisel Tip for leadfree soldering 960-T-3.2D3.2
25mm0.7
Long Chisel Tip for leadfree soldering 960-T-1.2LD1.2
Sloped Tip for Solar Panels 17mm
960-T-3CØ3
Sloped Tip for Solar Panels
Sloped Tip for Solar Panels
17mm960-T-4CØ4
17mm960-T-5CØ5
Round Tip for fine soldering 960-T-IR0.2
R0.2
17mm
215mm
Round Tip for fine soldering 960-T-BR0.5
R0.5
17mm
Knife Tip for SMD soldering 960-T-K5.0
Tip for SMDSoldering
960-T-3CMØ3
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
shown trademarks are property of their respective owners. Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,
Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
reliable & caring since 1976
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected]: 8283820745 & 9316134502
Solder Feeder and attachment for Soldering Pencil
Add to raise production rate to avoid solder wire wastage&optional Auto Solder Wire Feeder
Today’s highly competitive environment, always demand high possible productivity of each operators as well saving
every paisa. For such demanding requirements, the optionally available Auto Solder Feeder Model SFS81 with
36Digital Soldering Station DSS is the right choice. Besides increasing productivity of operator, it also provides consistent quality for each solder joint as same amount of solder wire
.with pre-programmed feeding is applied
Low Cost High Production Workhorse Soldering Station Model DSS36
Low capital investment + low running cost, uses lower priced Soldering Tips
Assured availability, normally ex-stock, of Spare Parts for Soldering Pencil
12
3 4
Barrel & Nut Assembly
Heater Enclosure
Heating Element
Cord with Connector
SNo. Description Remarks
Whenever required
Whenever required
Replace if display shows H-E/S-E
Whenever required
1
2
3
4
Available for Solder Wire of diameter from0.8 ~ 2.0 mm. (customer need to specify)
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
shown trademarks are property of their respective owners. Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
reliable & caring since 1976
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected]: 8283820745 & 9316134502
Model DSSLF04HESD is a alue- or- oney (VFM) Soldering Station with intelligent features as supervisor can program V F Mtwo most commonly used production process temperatures for instant recalling during operation. He can also lock limits of temperature range (i.e if he sets mode 01 or 11 for upper temperature limit of 400°C, operator cannot solder beyond that temperature). It displays both SET temperature and ACTUAL temperatures simultaneously. It also has in-built digital temperature offset calibration feature to meet ISO 9000 requirements. Unique integrated design of Soldering Tip, Barrel and complete encasing of Metallic Heating Element, provides reliable soldering joints with higher production rate.
Main Power Control Unit also has EMI & & Surge Suppression Filter to suppress transients of mains power line.
Scope of Supply
• ESD Safe Main Power & Control Unit
ESD Safe light weight Soldering Pencil •
fitted with 200G-2.4D Chisel 2.4mm Soldering Tip
Combined Dry & Wet Tip Cleaner Support Rack•
Single Soldering Station suitable for Leadfree, SMD ICs, Solar Cells, LEDs and igh ass soldering jobsH M
Fine pitch SMD Soldering Thru-hole Soldering Solar Cell Soldering SMD LED SolderingHigh Mass Soldering
Salient Features
● Power/Control unit has in-built following features: - Password protection - In-built temperature calibration - Sleep Timer for longer life - Error message indication - One touch temperature recalling
● Similar European Soldering Stations are 2.5 times costlier
● Reliable heating element does not require frequent changing
● Low running cost due to low priced/long life soldering tips
● Every spare part is available ex-stock to minimize down time.
Integrated single piece Tip & Barrel fully encase Metallic Heating Element. This uniqueness results in high heat energy storage for faster heat transfer
at mere 40% price than of similar German make but with far higher performance@& rarely needs replacement of Heating Element, much lower Soldering Tips price
Highest Value-For-Money Digital oldering Station Model DSSLF04HESDS
Specifications
• Power Temperature Range• Sleep Time (minutes)• Temperature Stability• Tip to Ground Potential• Tip to Ground Resistance•
: 90 Watts : 100°C ~ 500°C: 0~99 (adjustable): ± 2% of final value: < 2 mV: < 2 ohm
RoHSCompliant
L E A D
F R E E
• It has a password locking function Push-Button control and with auto-sleep function• Various types of long life Soldering Tips available•
Features
• Lightweight and comfortable for fatigue-free workingReal and fully electrostatic safe ESD design• in-built calibration feature to meet ISO requirements•
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
reliable & caring since 1976
shown trademarks are property of their respective owners.
Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
Soldering Tip
Heating Element
Replace if worn out
Replace if display shows H-E
S.No. Description Remarks
1
2
1 2
3
4
Sensor
Nipple for Tip
Replace if display shows S-E
Replace whenever required
S.No. Description Remarks
3
4
Unbreakable, far longer life & lower pricedeating lement of Soldering PencilH E
Unbreakable eating lementH E
in coiled form encased in metal tube
Sensor is veryclose to the
oldering ip for S Tprecise controlof temperature
Easy and faster change of Soldering Tip due to push fit design
Though rarely required to change, the Heating Elementhas its unique Push-fit designto ensure quick replacement.
Unique Soldering Tip for solderingultra-fine pitch large size SMD ICs
Specially designed 200G-CM SMD Soldering Tip has concave cavity to hold molten solder. It helps to solder one side of largesize IC completely in a single run by dragging SolderingSMD Tip on all PCB smoothly to ensure bridge-less solderingpads
Solder Feeder and attachment for Soldering Pencil
Add to raise production rate to avoid solder wire wastage&optional Auto Solder Wire Feeder
Today’s highly competitive environment, always demand high possible productivity of each operators as well saving every
paisa. For such demanding requirements, the optionally available Auto Solder Feeder Model SFS81 with Digital Soldering Station DSSLF04HESD is the right choice. Besides increasing productivity of operator, it also provides consistent quality for each solder joint as same amount of solder wire with
.pre-programmed feeding is applied
Highest Value-For-Money Digital oldering Station Model DSSLF04HESDS
Assured availability (normally ex-stock) of Spare Parts for Soldering Pencil
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
reliable & caring since 1976
shown trademarks are property of their respective owners.
Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
at mere 40% price than of similar German make but with far higher performance@& rarely needs replacement of Heating Element, much lower Soldering Tips price
Available for Solder Wire of diameter from0.8 ~ 2.0 mm. (customer need to specify)
Part Number
200G- D0.80.8
Wide range of Soldering Tips are available for different applicationssoldering
Chisel Tip for leadfree soldering B
C16
Width A (mm)Description Dimensional Diagram
200G-B
Tip for SMD Soldering
200G-3C
16
17
Round Tip for Fine Soldering
200G-2CM2
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
ETDC (STQC) Test Report of DSSLF04HESD Soldering Station
shown trademarks are property of their respective owners.
Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
• DSSLF150ESD Power & Control Unit
DSP150 Soldering Pencil fitted with Soldering Tip •
• Support Rack with Dry Cleaner & Cleaning Sponge
Scope of Supply
Model DSSLF150ESD Soldering Station is ESD Safe and have PC Interface Port for online monitoring of 63 unitssimultaneously. This Soldering Station is best value-for-money in place of investing in 3~4 Soldering Stations as this the one single Soldering Station is adequate to achieve similar production rate because of its faster thermal recovery and
ing Because of higher heating power, soldering can be done at lower temperature for more reliability higher heat power. of solder joints. ;Other features are: in-built Temperature Off-Set for Digital Calibration to meet ISO 9000 requirements
( s ) ensures longer life of Heating Element in-built function of Auto-Sleep and Auto Shut-Off get activated automaticallyand Soldering Tips all 3 ized s to ensure s the . Supervisor can lock optim process temperature operator cannot changesame Very wide range of Soldering Tips from 2.4mm width with different geometrical shapes, as required for . to 16 mm different soldering applications, are readily available. Also we can provide customized Tips.
High Power new150 Watt Digital Soldering Station Model DSSLF150ESD
3 Process Temperatures o can be pre-programmedOptimized for on-line pr duction use All Spare Parts and all Soldering Tips are normally available with immediate delivery
Touch Button
Control Panel
Heavy Duty Wobble-free Holder for Soldering
with both Dry Cleaner Pencil and (for leadfree soldering)
also Wet Cleaning Sponge
Light Weight 150 Watt Soldering Pencil is comfortable for operator's working
LCD Digital Display
“ESD” Safe
Salient Features
● Power/Control unit has in-built following features: - Touch Button Control Panel - Password Protection - In-built Temperature Calibration - Sleep Time Mode for longer life - Error Message indication - 1-Touch Temperature Recalling
● Reliable eating lement lowers H Eproduction running cost
● L erow priced long life Soldering Tips lowers production running cost
● Normally IMMEDIATE de ivery for lSpare Part to keep investment sproductive
ESD Status
Unit
Lock Status
Alarm Status
Heating Status
CH1 CH2 CH35
4
4
3
3
3
5 5
Main Power/Control Unit has EMI and Surge Suppression Filter to suppress
transients of mains power line.
Touch Screen Control Panel
3-Process Temperature Selection Switch
UP Key
DOWNKey
ON/OFF Key
34
5
RoHSCompliant
L E A D
F R E E
High Mass Automotive Components soldering Power Capacitors soldering Solar Panels & Cells reliable soldering
Provision to store the spare Soldering Tips
Detachable Stand for easy cleaning of spread out solder in the Stand shown trademarks are property of their respective owners.
Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
• Power Temperature Range • • Temperature StabilityTip to Ground Resistance• Tip to Ground Potential• Dimensions(LxWxH)•
: 150 Watt, 220V/50Hz: 100°C ~ 480°C: ±2% of final value: <2Ω: <2mV: 137 x 168 x 114mm (approx.)
Specifications
Cooling Fan
ON/OFFSwitch
PC Interface Port
GroundingSocket
Wide range of Soldering Tips for heavy mass soldering are available.normal to
High Power new150 Watt Digital Soldering Station Model DSSLF150ESD
Description Actual Photo ModelWidth (mm) Thick (mm) Dimensional Diagram
500A-16D01Special Tip12
8
- 500-7P-1Round Tipfor Solar
Ø7Ø7
- 500-8CFSloped Tip forAutomotive
Ø8Ø8
500- D2.4Chisel Tip forLeadfree soldering 2.02.42.4
42
500- D52.55.02.5
5
4
Chisel Tip forFilm Capacitors
500- D4 -032.04.0Chisel Tip forFilm Capacitors 2
4
4
500- D6.71.86.71.8
6.7
12
Chisel Tip for Energy Meters
500-8D2.582.5
8
6
Chisel Tip forFilm Capacitors
500- D3.52.03.5Chisel Tip 3.542
500A-10D210Chisel Tip forFilm Capacitors
500A-L8C01-Bent Sloped Tip
Ø5Ø5
500-5CSloped Tip -
Ø4Ø4 500-4CSloped Tipfor Solar
-
Ø3Ø3 500-3CSloped Tipfor Solar
-
Ø6Ø6 500-L6CSloped Bent Tip
-
Ø5Ø5 500-L5C01Sloped Bent Tip
-
3 Process Temperatures o can be pre-programmedOptimized for on-line pr duction use All Spare Parts and all Soldering Tips are normally available with immediate delivery
shown trademarks are property of their respective owners.
212
10
Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
reliable & caring since 1976
shown trademarks are property of their respective owners.
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
Specifications
• Power
Input Supply•
Temperature Range •
• Temperature Stability
Tip to Ground Resistance•
Tip to Ground Potential•
: 320 Watts
: 220VAC, 50Hz
: 50°C ~ 600°C
: ±2% of final value
: < 2 Ohm
: <2mV
• Precise temperature settings by pressing push buttons
In-built temperature offset provision for digital calibration•
In-built programing functions of auto sleep and shut-off•
Supervisor can lock optimized process temperature•
• 6~12 mm wide Soldering Tips for different applications
Features
Few examples of Automotive omponents, Power Capacitors and Large Coils soldering applicationsC
ApplicationspecficSoldering Tips
Heavy Duty Soldering
PencilHolder
SET & ACTUALTemperatures
are digitallydisplayed
Digitized Pushbuttons
for precise temperature
control
Main Power & Control Unit
New Barrel & Nut design for
easy replacement of Soldering Tips
• Power & Control Unit
• Soldering Pencil
Soldering Tip 8 mm Chisel•
• Heavy Duty Support Rack
• Cleaning Sponge
Scope of Supply
for Auto Components, Power Capacitors & Coils soldering applications
320 Watt Soldering Station Model DSSHP300Very High Power
RoHSCompliant
L E A D
F R E E
Customer’s Name & City Date of SaleSl. No. Qty
Bharat Electronics Limited, Mumbai
Epcos India Private Limited, Nashik
Epcos India Private Limited, Nashik
Epcos India Private Limited, Nashik
Epcos India Private Limited, Nashik
Epcos India Private Limited, Nashik
GRD Induction, Jalandhar
Koti Systems, Bangalore
Koti Systems, Bangalore
Nitin Jain, Nashirabad
Schneider Electric India Pvt. Ltd., Bangalore
Schneider Electric India Pvt. Ltd., Bangalore
Secure Meters Limited, Udaipur
Secure Meters Limited, Udaipur
Secure Meters Limited, Udaipur
Synergy Enterprises, Chandigarh
Terminal Ballastics Research Laboratory, Chandigarh
08.03.2017
20.02.2012
30.03.2012
02.07.2016
28.08.2016
08.12.2016
16.09.2015
04.06.2015
26.06.2016
09.03.2013
13.03.2013
30.12.2014
30.12.2015
10.02.2016
20.08.2016
16.09.2014
26.04.2014
5
1
3
2
1
4
1
1
1
1
1
2
2
3
3
1
4
1
2
3
4
5
6
7
8
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
Wide range of Soldering Tips for very high mass soldering applications are available.
502-6D6A
2.5
502-8D8A
2.5
502-12D12A
2.5
502-12A12Special for Tip Power Capacitor soldering
for Auto Components, Power Capacitors & Coils soldering applications
320 Watt Soldering Station Model DSSHP300Very High Power
Part Number
Chisel Tip for leadfree soldering
Width A (mm)Description Dimensional DiagramActual Picture
Chisel Tip for leadfree soldering
Chisel Tip for leadfree soldering
26
A
4.4
Partial User References (not complete list) of our DSSHP300 Soldering Station
shown trademarks are property of their respective owners.
Warranty is 12 months from the date of invoice. It excludes all consumable parts as Heating Elements,Temperature Sensors, Soldering Tips, Cleaning Sponges, Cleaning Brass Wool and mechanically damaged parts.
Control Unit with close loop precise PID temperature control
Digital display of temperatures
Pushbuttons for precise
temperature control
Solder feed length, speed and time programming switches
Note: Solder wire roll is not a part of supply.
Today’s highly competitive and demanding industrial soldering applications need highest possible productivity of
operators and every paisa must be saved for profitability. Such demanding requirements are met with Fast
Thermal Recovery Digital Soldering Station with Auto Solder Feeder Model DSF76D. Affordably priced, it is the
right choice. Besides making one hand of operator free, it also provides consistent quality for each solder joint as
same amount of Solder wire with pre-programmed feeding is applied at optimized process temperature.
• Main Controller & Feeder Unit
Soldering Pencil with Wire• Feeding attachment
Chisel Soldering Bit• Soldering Pencil Holder•
Scope of Supply
• Fast heating and rapid thermal recovery
ensure defect free leadfree soldering.
• Precise temperature settings by keys
• In-built calibration offsets & auto-sleep
• Adjustable feeding speed of solder wire
• Adjustable feeding length of solder wire
• Adjustable interval time & returning time
Features
Temperature Range • • Temperature Stability
Tip to Ground Resistance• Tip to Ground Potential• Input Supply• Feeding Speed• *Feeding Interval Time• *Feeding Length• *Returning Time• *Feeding Mode• *Diameter of Solder Wire •
* These functions can be set from front panel.
: 200°C ~ 480°C : ± 2% of final value: <2 Ohm: <2mV: 230VAC, 50 Hz: About 2.7mm/s~27mm/s: 0~2.7s: 0~150mm: 0~0.9s : Auto (1~9) / Manual (0): customer to specify
Specifications
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
90 Watt Model DSF-76D Soldering Station with Solder Wire Feeder
increases productivity & lowers production cost with no solder wire wastage
lowers overall production cost through higher productivity
and avoids solder wire wastage
RoHSCompliant
L E A D
F R E E
shown trademarks are property of their respective owners.
Warranty is 12 months from the date of invoice. It excludes consumable parts as Heating Element, Sensor, Soldering Tip, Cleaning Sponge & Gears and any mechanically damaged parts.
Note: Available for Solder Wiredia from 0.8 ~ 2.0 mm. (customerneed to specify dia of the SolderWire while ordering)
Wide range of Soldering Tips are available for different soldering applications
0.53
12
1 Barrel & Nut Assembly
Soldering Tip2
Heater Enclosure (Nipple)3
SN Description Remarks
Handle4
Whenever required
Replace if worn out
Whenever required
Whenever required
21
5
6
4
3
Heating Element Replace when display shows H-E
5 Temperature Sensor Replace when display shows S-E
6
Assured availability, normally ex-stock, of spare parts for both Soldering Pencil
Part Number
200-1.6D1.6
Width A (mm)Description Dimensional DiagramActual Picture
Chisel Tip for leadfree soldering
0.53
12
Chisel Tip for leadfree soldering 200-2.4D2.4
0.53
10
Chisel Tip for leadfree soldering 200-3.2D3.2
Chisel Tip for leadfree soldering 0.5
310
200-4.2D4.2
Sloped Tip for Solar Panels 12
200-3CØ3
Sloped Tip for Solar Panels
200-4CØ412
Round Tip for leadfree soldering 200-2BR2
0.5 312
R2.0
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
shown trademarks are property of their respective owners.
Warranty is 12 months from the date of invoice. It excludes consumable parts as Heating Element, Sensor, Soldering Tip, Cleaning Sponge & Gears and any mechanically damaged parts.
90 Watt Model DSF-76D Soldering Station with Solder Wire Feeder
increases productivity & lowers production cost with no solder wire wastage
Model DSF-76D-150 Hi-Power Soldering Station with Solder Wire Feeder
used by many customers for soldering of Solar Panels & Automotive components
Integral Solder Wire Feeder and 150 Watt Soldering Pencilupto 2.0mm
RoHSCompliant
L E A D
F R E E
Digital Display for Temperature
Digitized Pushbuttons for precise temperature control
Finger Switchfor Feeding
desired lengthof Solder Wire
at SET speed
Solder WireFeedingAssembly
150 WattSoldering Pencil
SolderingPencilStand
Solder Feed Length, Speed and Time Programming Switches
Note: Solder Wire Roll is not a part of supply.
• Main Controller & Feeder Unit
• Soldering Pencil
Soldering Bit• • Soldering Pencil Holder
• Solder Wire Feeding Attachment
Scope of Supply
Note: Available for Solder Wiredia from 0.8 ~ 2.0 mm. (customerneed to specify dia of the SolderWire while ordering)
Soldering with Solderwire Feeder Example
High Mass Automotive Components soldering Power Capacitors soldering Solar Panels & Cells reliable soldering
Today’s highly competitive and demanding industrial soldering applications need highest possible productivity of operators and every paisa must be saved for avoiding wastage of Solder Wire. Such demanding requirements are met with fast thermal recovery Model DSF-76D-150 Hi-Power Soldering Station with Solder Wire Feeder. Besides making one hand of operator free, it also provides consistent quality for each solder joint as same amount of Solder wire with pre-programmed feeding is applied at optimized process temperature.
Temperature Range • • Temperature Stability
Tip to Ground Resistance• Tip to Ground Potential• Input Supply• Feeding Speed• *Feeding Interval Time• *Feeding Length• *Returning Time• *Feeding Mode• *Diameter of Solder Wire•
* These functions can be set from front panel.
Specifications
: 50°C ~ 550°C: ±2% of final value: <2Ω: <2mV: 230VAC, 50Hz: About 2.7mm/s~27mm/s: 0~2.7S: 0~150mm: 0~0.9s: Auto (1~9) / Manual (0): customer to specify
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
Warranty is 12 months from the date of invoice. It excludes consumable parts as Heating Element, Sensor, Soldering Tip, Cleaning Sponge & Gears and any mechanically damaged parts.
shown trademarks are property of their respective owners.
Wide range of Soldering Tips for heavy mass soldering are available.normal to
Description Actual Photo ModelWidth (mm) Thick (mm) Dimensional Diagram
- 500-7P-1Round Tipfor Solar
Ø7Ø7
- 500-8CFSloped Tip forAutomotives
Ø8Ø8
500- D2.4Chisel Tip forLeadfree soldering 2.02.42.4
42
500- D52.55.02.5
5
4
Chisel Tip forFilm Capacitors
500- D4 -032.04.0Chisel Tip forFilm Capacitors 2
4
4
500- D6.71.86.71.8
6.7
12
Chisel Tip for Energy Meters
500-8D2.582.5
8
6
Chisel Tip forFilm Capacitors
500- D3.52.03.5Chisel Tip 3.542
500A-10D210Chisel Tip forFilm Capacitors 2
12
10
500A-L8C01-Bent Sloped Tip
Ø5Ø5
500-5CSloped Tip -
Ø4Ø4 500-4CSloped Tipfor Solar
-
Ø3Ø3 500-3CSloped Tipfor Solar
-
Ø6Ø6 500-L6CSloped Bent Tip
-
Ø5Ø5 500-L5C01Sloped Bent Tip
-
Assured availability, normally ex-stock, of Spare Parts for Soldering Pencil
1 Barrel Assembly
2
S.No. Description Remarks
Replace if worn out
3
Heating Element Replace if display shows H-E
Sensor Replace if display shows S-E
12
3
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
Model DSF-76D-150 Hi-Power Soldering Station with Solder Wire Feeder
shown trademarks are property of their respective owners.
Warranty is 12 months from the date of invoice. It excludes consumable parts as Heating Element, Sensor, Soldering Tip, Cleaning Sponge & Gears and any mechanically damaged parts.
used by many customers for soldering of Solar Panels & Automotive components
reliable & caring since 1976
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
Auto Solder Wire Feeder Model SFS81 for various Soldering Stations
increases producti lower costvity of operator and avoids solder wire wastage to
Guide Tube for Solder Wire
Screw for PressureAdjustment
Directional Fixing Tube for Feeder Tube Head
HandSpike
Feeder Tube Head
Plug for Finger Switch
Finger Switch Guide Tube
• Power ConsumptionMotor •
• Feeding Time*Feeding Speed• *
• Feeding Interval Time*Returning Length• *Feeding Mode• *For Solder Wires of dia•
* These functions can be set from front panel.
: 20 Watt, 220V/50Hz: DC Motor: 0 ~ 4s: 4mm/s ~ 21mm/s: 0 ~ 3.6s: About 0 ~ 30mm: Auto (1~9) / Manual (0): 0.8 ~ 2.0 mm (customer to specify)
Specifications
Return Time Setting: Press Returning Length Switch "RETURN" to set the suitable digit in accordance withworking demand. Returning length is designated with one digit. 0 to 9 denotes the returning length from 0 ~ 30mm.
Feeding Interval Time Setting: Press Interval Setting Switch "INTERVAL" to set the suitable digit. Feeding Interval Time means the interval time between every feeding when the automatic feeding is over two times. Feeding Interval Time is designed with one digit. 0 to 9 denote interval time from 0 ~ 3.6 seconds. When the digit is set as 1, the interval time is about 0.4 second. When it is set as 9, the interval time is 3.6 seconds.
Feeding Speed Setting: Press Feeding Speed Switch "SPEED" to set the suitable digit in accordance with working demand. Feeding Speed is designed with one digit. 0 to 9 which denote feeding speed from 4mm/s ~ 21mm/s. When the digit is set as 0, the speed is lowest and is about 4mm/s. When it is set as 9, the speed is fastest and is about 21mm/s.
Feeding Mode Setting: Press the Feeding Mode Switch "MODE" to choose suitable digit. After each time feeding of Solder Wire for soldering, the Solder Wire will get back. This ensures same quality of soldering for each solder joint.Available Feeding Modes are: 0: Manual Feeding; 1: Auto Feeding once; 2: Auto Feeding Twice; 3: Auto feeding Three times; 4: Auto Feeding Four Times; 5: Auto Feeding Five Times; 6: Auto Feeding Six Times; 7: Auto Feeding Seven Times; 8: Auto Feeding Eight Times; 9: Auto Feeding Nine Times
Available all of followingfor Models of Soldering Stations
• DSS36DSSLF04HESD• DSSLF120-UF• DSSLF150ESD• DSSHP03G• Weller WSD81•
Length Switch
Return Switch
IntervalSwitch
SpeedSwitch
ModeSwitch
ON/OFFSwitch
ManualReturnSwtich
ManualFeed
Swtich
Feeding Length Setting: Press Feeding Length switch "LENGTH" to set suitable digit in accordance with working demand. Feeding length is designated with
0 which three digits. 00 to 999 denote feeding length of 0.15mm to 150mm. When the digit is set as 001, the length
it 999 150is 0.15mm. When is set as , the length is mm.
Description of Main Funtions:
Many industrial, automotive (lights, magneto etc.) and other production lines require faster soldering processwith consistent quality. SFS81 Solder Feeder system, economically priced, is the right choice for such applications since it makes operator’s hand free with auto solder wire feeding, also provides quality consistency to each solder joint due to same solder amount with pre-programmed solder wire feeding.
Warranty is 12 months from the date of invoice. It excludes consumable parts as gears and any mechanically damaged parts.
shown trademarks are property of their respective owners.
Note: Solder Wire Roll is not a part of supply.
Warranty is 12 months from the date of invoice. It excludes all consumable parts as Sensor etc. and any mechanically damaged parts.
reliable & caring since 1976
Scope of Supply
Specifications
• Measures soldering tip temperature quickly Auto shut-off function, MAX HOLD s• Both Celsius and Fahrenheit types readings possible.•
and K-type & Star type thermocouples for surface tip temperature measurement •
Digital Calibration Meter K-type Thermocouple • • Star type Temperature Sensors set of 10 pcs•
• Resolution Measurement Range• Accuracy• Sensor• Battery Indication• Power Supply• Dimensions/Weight•
: 1°C (1°F): 0~800°C (32~1 °F)500: ± °C ± °5 ( 10 F): K-type Thermocouple: Alarm: 9 Volt DC Battery: 14 x35x8 mm 250 grams (approx.)7 5 /
K-type Thermocouple
Low Cost and popular Digital Calibration Meter for Soldering Stations P/N: I191-AD
Digital Calibration Meter for Hot Air Rework Stations P/N: ISC3196
Specifically designed for calibration of Hot Air Station. • Sensor measures temperature of air outlet quickly• Auto Shut-off function available, time can be programmed• MAX HOLD records the highest temperature•
: 1°C (1°F): 0~800°C (32~1 °F)500: ± °C ± °5 ( 10 F): K-type Thermocouple: LCD display: 9 Volt DC Battery: 1 x x m (approx.) 80 79 138m: 2 0 grams (approx.)0
Specifications
LCD Display Testing
Socket
• Resolution Measurement Range• Accuracy• Sensor type• Display• Power Supply• Dimensions• Weight•
To measure mV and Ohm values,
connect Soldering tS ation thru
Soldering Calibrator
mV/OHM/TEMPSelection
Switch
Connector for K-typeTemperatureSensor
Ohm and mVTesting Plate
GroundingPoint
Top-of-the-line Digital Soldering Calibrator3-in-1 (mV/Ohm/Temp) P/N: ISC3192
Measures Resistance Tip to Ground & Tip TemperatureTip to Ground , Leakage Voltage
Can also calibrate Solder Pots with rod thermocouple probes• Uses high precision micro-computer check• Meets MIL-STD-2000 leak voltage measurement standard•
Specifications:Measuring Range
Resolution
Accuracy
Temperature SensorPower ConsumptionDimension (approx ).Weight (approx ).
: 20~600°C/32~1 00°F0~90 mV (AC): 0~90 Ω: 0.1mV: 0.1 Ω: 1°C/1°F: ±3°C / ± °F: 6±(3%±2 digit): ±(1%±2 digit):
: K-Type Thermocouple1W:
( )x ( )x ( ) mm: 158 L 150 W 50 H1.1 Kg:
- TemperatureVoltage- Resistance-
- VoltageResistance- Temperature-
- TemperatureVoltage- Resistance-
Digital Calibration Meter for Soldering Stationss and Hot Air Stations
shown trademarks are property of their respective owners.
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
Website: www.indeonline.in Phones: 0172-4614415 & 4640415 Email: [email protected] Cell: 9316134502
Temperature Sensors (star type)
P/N: 192-212