mt01_assembly_05

Please glue them by aligning the red and red/blue and blueparts if they are marked on the paper.

2

Note

Basic working method and markingsTo begin

How to assemble

Tools and materials needed

Items of Caution

-Ruler - scissors - blade cutter or "Exacto-knife" - awl or

other pointed tool (for making a folding crease) - felt pen

- pin set - glue - hand towel ( for cleaning your fingers) -

dictionary or other heavy book ( to press the papers flat).

*Take care when using sharp or pointed objects or when

using bladed cutting tools. Place a heavy sheet of paper

under the paper you want to cut.

*Use glue and other adhesives only in well-ventilated

areas.

*When printing, use a slightly reduced font size. There

may be differences in dimensions, depending on the

type of printer used.

*Follow the working method and markings carefully.

*Cut carefully along the outter line with cutting blade,

Exacto-knife or scissors.

One - point Advice

*Before beginning assembly, test adhesive amounts

on extra paper.

*Cut carefully with cutting blade, Exacto-knife or

scissors.

*Occasionally, white spots will be apparent on folds

and cuts. Use a marker or pencil to fill in these spots.

It is recommended that this be done after each stage

of assembly because coloring becomes more difficult

once parts are assembled.

*As an adhesive, white wood glue is recommended.

Avoid over application as this may cause the paper to

wrinkle.

*For folding parts, first use an awl or other pointed

tool to make a light crease along the dotted or solid

line. This will make the folds straight. Avoid making

strong creases, as this will cause the paper to tear.

Cut along these lines.Dotted line

Fold along these lines. The printed surface should beon the inside of the folded shape.

Broken lines

Fold along these lines. The printed surface should beon the outside of the folded shape.

Solid lines

Do not fold or cut the partsmarked .

Red dots are the referencepositions for gluing surfaces.

Cut out parts marked with anasterisk(*).

Reference photo

3

Indication of Working Methods

First, assemble each component by following the working

method and markings. Then, refer to the illustration and

photos below to glue the parts together.Foldor Curve Glue

11 Assembling the Tail Light

Fold each relevant part according to the assembly symbols.

Please use the dots on each component as reference when gluing surfaces.Tail LightSheet L, 14 parts in total

1

2

344

4

5

6

7

8

8

9

9

10

10

Connect each of the previously assembled parts in order from - according to the diagram.1 10

L-10

L-6

L-4

L-2

L-5

L-1

L-3

L-13

L-14

L-9

L-8

L-7

L-11

L-12

4





12 Assembling the Front Tire


Please use the dots on each component as reference when gluing surfaces.Front TireSheet M, 12 parts in total

Reference photo

1

1

2

2

3

3

4

4

5

6

6

6

6

1Glue in order from to on the graphic.6

M-16

M-17

M-15

M-21

M-20

M-19

M-18

M-14

M-22

M-23

M-12

M-13

5





12 Assembling the Front Tire


Please use the dots on each component as reference when gluing surfaces.Front TireSheet M, 23 parts in total

Reference photo

1

2

2

3

4

4

4

4

5

5

5

5

6

6


M-9

M-3

M-11

M-4

M-7

M-8 M-10

M-6

M-5

M-2M-1

Front Tire

6





13 Assembling the Rear Tire


Please use the dots on each component as reference when gluing surfaces.Rear TireSheet N, 12 parts in total

Reference photo

1

1

2

2

3

3

4

4

5

6

6

6

6

1Glue in order from to on the graphic.6

N-11

N-12

N-13

N-15

N-18

N-16

N-14

N-10

N-17

N-19

N-8

N-9

7





13 Assembling the Rear Tire


Please use the dots on each component as reference when gluing surfaces.Rear TireSheet N, 19 parts in total

Reference photo

1

2

2

2

2

3

3

3

3

4


N-2

N-5

N-4

N-1

N-7

N-3

N-6

Rear Tire

Glue the engine onto the lower part of the frame.

2

3

4

5

6

7

8

9

10

11

13

1

12

Glue the lower part of the frame to the upper part of the frame.

Insert the intake to the engine.

Insert Exhaust 2 and 3 into the engine.

Insert Exhaust 5 into Exhaust 2 and 3, then glue them to the frame.

Glue the tail light to the frame.

Glue Exhaust 1 to the seat.

Glue the seat to the frame.

Glue the tank to the frame.

Insert Exhaust 4 into Exhaust 1 and 5.

Glue the rear tire to the rear arm.

Glue the rear arm to the frame.

Glue the side cover to the frame and the engine.

Glue the left footrests to rear arm.

Glue the right footrests to the engine.

Put the lower part of the steering through the frame and glue it to the upper part of the steering.

Glue the headlight to the upper part of the steering.

Glue front tire to the lower part of the steering.

14

15

16

17

18

8

14 Finish

Please use the dots on each component as reference when gluing surfaces.


13

18

Upper Frame

Column

1

22

34

45

5

5

6

78

9

10

10

1010

1112

12

13

1313

13

14

15 16

16

17

Fuel Tank

Exhaust Pipes 1

Rear Arm

Side Covers

Front Tire

Rear Tire

Engine

Seat

Lower Frame Column

Intake

Upper Steering Column

Side Covers

Side Covers

Side Covers

Left footrests

Tail light

Exhaust Pipes 4Headlight

Right footrests

Lower Steering Column

Exhaust Pipes 3

Side Covers

ExhaustPipes 5

ExhaustPipes 2

RIGHT FRONT

9

15 Assembled Model and the List of Parts

Please refer to the photo below when attaching each component.

SeatSheet I, 8 parts in total

FrameSheet C, 75 parts in total

EngineSheet A, 147 parts in total

Right footrestsSheet K, 22 parts in total

Exhaust PipesSheet H, 53 parts in total

SteeringSheet E, 74 parts in total

HeadlightSheet F, 24 parts in total

LEFT REAR

10

15 Assembled Model and the List of Parts

Please refer to the photo below when attaching each component.

Tail lightSheet L, 14 parts in total

Rear ArmSheet D, 36 parts in total

Left footrestsSheet J, 15 parts in total

Side CoversSheet B, 20 parts in total

Front TireSheet M, 23 parts in total

Fuel TankSheet G, 11 parts in total

Rear TireSheet N, 19 parts in total

Documents

mt01_assembly_05