Λειτουργό Διοίκησης (CYS) · 2021. 1. 8. · Information procedure Page 1 Monthly Notifications Register Notifications registered at CCMC from 2017-08-01 to 2017-08-31

Λευκωσία, 27 Δεκεμβρίου 2017

Κυρία/ε, Σας επισυνάπτoυμε γνωστοποιήσεις από Εθνικούς Οργανισμούς Τυποποίησης, μελών των Ευρωπαϊκών Οργανισμών Τυποποίησης CEN/CENELEC, που περιέχουν τους τίτλους προτεινόμενων εθνικών προτύπων. Σύμφωνα με την Ευρωπαϊκή Οδηγία που αφορά την πληροφόρηση σε θέματα τεχνικών προτύπων, μπορείτε, αφού μελετήσετε τους τίτλους: α) να ζητήσετε όπως λάβετε ηλεκτρονικά ολόκληρο το κείμενο του προσχεδίου εθνικού προτύπου, εάν αυτό είναι διαθέσιμο, β) να συμμετάσχετε στις συναντήσεις της τεχνικής επιτροπής του Εθνικού Οργανισμού Τυποποίησης που ετοιμάζει το προσχέδιο προτύπου και γ) να υποβάλετε εισήγηση στον CYS, να αρχίσει τυποποιητική εργασία σε Ευρωπαϊκό επίπεδο σχετικά με το θέμα της γνωστοποίησης, εάν φυσικά πιστεύετε ότι το εν λόγω εθνικό πρότυπο θα επηρεάσει την ελεύθερη διακίνηση προϊόντων ή την κυπριακή βιομηχανία και οικονομία. Τυχόν σχόλια και παρατηρήσεις παρακαλώ όπως υποβάλλονται στον Κυπριακό Οργανισμό Τυποποίησης. Σε περίπτωση που δε λάβουμε καμία ανταπόκριση, ο CYS δε θα φέρει ένσταση στην προώθηση των υπό αναφορά εθνικών προτύπων. Για περισσότερες πληροφορίες μπορείτε να επικοινωνείτε με την κα. Μαριλένα Νικολάου, Λειτουργό Διοίκησης και Διεθνών Σχέσεων του Κυπριακού Οργανισμού Τυποποίησης (CYS), τηλ: 22 411439, Φαξ. 22 411511 και στην ηλεκτρονική διεύθυνση: [email protected] Με εκτίμηση, Ανδρέας Ανδρέου, Διευθυντής Βιομηχανίας, για Γενικό Γραμματέα. /ΜΚ.

Γρίβα Διγενή 38 & Δεληγιώργη 3, 1066 , Τ.Θ. 21455, 1509 Λευκωσία, Κύπρος, Τηλ. + 357-22889860, Φαξ. + 357-22665685, E-mail: [email protected], Ιστοσελίδα:www.ccci.org.cy

mailto:[email protected]

mailto:[email protected]

http://www.ccci.org.cy/

Information procedure Page 1

Monthly Notifications Register

Notifications registered at CCMC from 2017-08-01 to 2017-08-31

Register issued on : 2017-09-01

A list of subsectors can be found at the end of this document.




Sector A : SERVICES


Page 3Subsector A09: FACILITY MANAGEMENT

Subsector : A09 Registration Date : 2017-08-29Organization : SNCountry : Norway

Project ID : NOT17032/0001 Project Established

ICS : 91.010.30National Ref : NS 6460Title : Operation of technical building installationsScope : This standard is a tool to increase the skills of the operating staff of technical building

installations, and point to laws and regulations. It points out different "dynamic" operational goals - how to achieve them and how to achieve continuous improvement. This standard point out some of the goals to be achieved, or any other potential that may be focused on. It describes how energy performance in a building can be developed, e.g. using NS-EN 15232. It also define/describe environmental goals and management as well as energy goals and management.

Relatedness :National : New

** End of Subsector **

Subsector A11: SAFETY AND SECURITY

Subsector : A11 Registration Date : 2017-08-01Organization : TSECountry : Turkey

Project ID : t1013660/0001 Project Established

ICS : 03.080.10National Ref :Title : Work place - Rules for compressed natural gaz (CNG) filling plants Scope : This standard structural features of CNG filling stations, management includes rules

regarding the characteristics and safety of employees.



Subsector A99: UNDETERMINED

Subsector : A99 Registration Date : 2017-08-28Organization : UNICountry : Italy

Project ID : 01603412/0001 Project Established

ICS : 03.060National Ref : UNI1603412Title : Personal financial planning - Guideline for the application of UNI ISO 22222:2008 - Part

1: Terminology, classification and requirements of service for plannersScope : This standard specifies criteria upon which personal financial planners, with suitable

professional competence, supports the clients in the definition and achievement of planned life objectives, respecting needs, obligations and preferences of the client

Relatedness :

Page 4

National : REV/AMD UNI/TS 11348:2010


** End of Sector **




Sector B : BUILDING AND CONSTRUCTION


Page 6Subsector B01: FIRE PROTECTION

Subsector : B01 Registration Date : 2017-08-07Organization : ASICountry : Austria


ICS : 03.080.20, 13.220National Ref : ÖNORM F 3700Title : Fire protection systems - GeneralScope : This ÖNORM defines the requirements for specialist companies for the planning, design,

installation, commissioning and maintenance of fire protection systems such as fire detection systems and fire incident control systems; gas extinguishing systems; wet extinguishing systems, fire prevention systems using an oxygen reduced atmosphere; electro acoustical alerting systems; Smoke and heat extraction systems (RWA) and alarm transmission systems.




ICS : 13.220National Ref : ÖNORM F 3072Title : Maintenance of wet extinguishing systemsScope : This ÖNORM defines the maintenance of water extinguishing, spray water and foam

extinguishing systems up to a nominal pressure of 25,0 bar as well as controls directly connected with certain types of water extinguishing systems. In addition to ÖNORM EN 12845, which is limited to sprinkler systems, this ÖNORM is to be applied to the entire range of wet extinguishing systems. Target of this ÖNORM is to define the tasks of the involved experts.




ICS : 13.220National Ref : ÖNORM F 3073Title : Maintenance of fire prevention systems using an oxygen reduced atmosphereScope : This ÖNORM defines the maintenance of fire prevention systems using an oxygen reduced

atmosphere. Target of this ÖNORM is to define the tasks of the involved experts.


Subsector : B01 Registration Date : 2017-08-03

Page 7

Organization : NENCountry : Netherlands


ICS : 13.220.20, 13.320National Ref : NEN 2575-3:2012/A2:2017 Concept nlTitle : Fire safety of buildings - Evacuation alarm installations - System and quality requirements

and guidelines for locating of alarm devices - Part 3: Loud alarm evacuation alarm installation type B

Scope : RThis document contains amendments of NEN 2575-3:2012.



Subsector B02: STRUCTURES

Subsector : B02 Registration Date : 2017-08-16Organization : DINCountry : Germany


ICS : 59.080.40National Ref : DIN 18204-1Title : Components for enclosures made of textile fabrics and plastic films (awnings) - Part 1:

Structures and tents




ICS : 59.080.40National Ref : DIN 18204-101Title : Components for enclosures made of textile fabrics and plastic films (awnings) - Part 101:

Conformity accessment for tents and halls according to DIN 18204-1



Subsector B10: TIMBER STRUCTURES

Subsector : B10 Registration Date : 2017-08-24Organization : SIST Draft Issue Date : 2017-11-01Country : Slovenia Latest Date for Comments : 2017-11-24


ICS : 91.080, 91.080National Ref : SIST EN 1995-1-1:2005/oA102:2017Title : Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for

Page 8

buildings - National AnnexScope : Standard SIST EN 1995-1-1:2005 gives general rules applicable to timber structures. National

annex determines the values for national choice through clauses where they are allowed.



Subsector B17: LIGHTING EQUIPMENT AND LIGHTING APPLICATION TECHNOLOGY

Subsector : B17 Registration Date : 2017-08-17Organization : SNV Draft Issue Date : 2017-08-15Country : Switzerland Latest Date for Comments : 2017-09-26

Project ID : CH170015/0001 Draft for public enquiry

ICS : 93.080.40National Ref : prSN 640551-1Title : Public lighting in street tunnels, galleries and underpasses - Part 1: Lighting

requirements, terms and quality features




ICS : 93.080.40National Ref : prSN 640551-2Title : Public lighting in street tunnels, galleries and underpasses - Part 2: Planning and design

of the lighting installation




ICS : 93.080.40National Ref : prSN 640551-3Title : Public lighting in street tunnels, galleries and underpasses - Part 3: Method for measuring

and evaluating quality features



Subsector B20: DRAINAGE EQUIPMENT

Subsector : B20 Registration Date : 2017-08-28

Page 9

Organization : UNICountry : Italy


ICS : 93.080.30National Ref : UNI1603451Title : Guideline for the installation for gully tops and manhole tops for pedestrian and/or

vehicular areasScope : This standard specifies the indications for the installation for gully tops and manhole tops,

within vehicular and pedestrian areas.

Relatedness :National : REV/AMD UNI/TR 11256:2007


Subsector B25: GAS DISTRIBUTION INSTALLATION AND RELATED EQUIPMENT

Subsector : B25 Registration Date : 2017-08-28Organization : UNICountry : Italy


ICS : 91.140.40National Ref : UNI1603299Title : Gasmeasurementsystems

HourlybasedgasmeteringsystemsInterchangeabilityofmeterswithQmax≤10m3/hwithpointtopointcommunication-Part12-2:Datamodel

Scope : This technical specification completes the requirements, already specified in the relevant parts of UNI/TS 11291 series, in order to allow interchangeability of gas meters designed for mass-market(<G10)thatcommunicateinpointtopointmode.This Part 12-2 defines the subset of the data model specified for interchangeability with exclusion of objects needed to manage the transmission media





HourlybasedgasmeteringsystemsInterchangeabilityofmeterswithQmax≤10m3/hwithpointtopointcommunicationPart12-4: PP4 Communication profile

Scope : This technical specification completes the requirements, already specified in the relevant parts of UNI/TS 11291 series, in order to allow interchangeability of gas meters designed for mass-market(<G10)thatcommunicateinpointtopointmode.Part 12-4 defines the objects needed for the management of the transmission media and statemachinesforcommunicationmanagement.

Page 10





HourlybasedgasmeteringsystemsInterchangeabilityofmeterswithQmax≤10m3/hwithpointtopointcommunicationPart12-6: Specifications for conformity assessment

Scope : This technical specification completes the requirements, already specified in the relevant parts of UNI/TS 11291 series, in order to allow interchangeability of gas meters designed for mass-market(<G10)thatcommunicateinpointtopointmode.This Part 12-6 defines a common pattern for conformity assessment



Subsector B26: ROAD BUILDING AND MAINTENANCE

Subsector : B26 Registration Date : 2017-08-31Organization : BSICountry : United Kingdom


ICS :National Ref : BS 1707Title : Roadsurfacedressing,bondcoats,seals,preservativesandothersprays

Specificationforthemethodoftestforbindersprayersforaccuracyofspreadofbinder(spray bar bench test)



Subsector B28: FLOOR COVERINGS



ICS : 97.150National Ref : ÖNORM B 5236Title : Planing and Laying of floor coveringsScope : This Austrian Standard specifies floor covering works with textile, elastic and laminate floor

coverings for internal use, also connected to installation of hot water underfloor heating systems. Parquets and timber floors are not covered by this Standard; these are dealt with by

Page 11

ÖBORMB2218andÖNORMBxx18.This Austrian Standard does not include provisions for bonding of wall coverings, for which particular requirements apply.



Subsector B33: BUILDING DESIGN

Subsector : B33 Registration Date : 2017-08-07Organization : MSZTCountry : Hungary


ICS :National Ref : MSZ 20378Title : Siting in nature areas. Design Plans intended to demonstrate integration into nature

areas. Detailed specifications of siting plans


Subsector : B33 (Secondary Subsector)

Registration Date : 2017-08-07

Organization : MSZTCountry : Hungary


ICS :National Ref : MSZ 20378Title : Siting in nature areas. Design Plans intended to demonstrate integration into nature

areas. Detailed specifications of siting plans



Subsector B99: UNDETERMINED



ICS : 91.010.10, 91.040.01National Ref : ÖNORM B 1802-1Title : Real estate evaluation - PrinciplesScope : This Austrian Standard is applicable to the calculation of values of the value of developed

and undeveloped real estate and parts of real estates, including parts such as buildings and outdoor facilities, as well as of building leases.


Page 12



ICS : 91.010.20National Ref : ÖNORM B 2204Title : Execution of vertical components - Contract to provide servicesScope : This Austrian Standard includes procedural and contractual provisions for the execution of

ofverticalcomponents.Exceptions are underground works in accordance with ÖNORM B 2203 (all parts), special civil engineering works according to ÖNORM B 2279.




ICS :National Ref : UNI1603450Title : Building and civil engineering works – Digital management of the informative processes –

Part 9: Informative management in working stage (Collaborative Digital Platform, Building Paper)

Scope : The standard defines the general criteria for the management of digital information during the use of the built environment (buildings, infrastructures and anthropomorphic environment).Moreindetail,thestandarddefinestheoperationalcriteriaof:- definition and acquisition of all the data needed to know the built environment (Digital DueDiligence)-coordination/organization,holdingandupdatingofthe“CollaborativeDigitalPlatform”- definition of the “building logbook” as a data management tool for existing building.



** End of Sector **




Sector C : CHEMICALS, CHEMICAL ENGINEERING AND FOOD PRODUCTS


Page 14Subsector C01: Food products

Subsector : C01 Registration Date : 2017-08-18Organization : LSTCountry : Lithuania


ICS : 67.060National Ref :Title : Grain products. Groats and flakesScope : This Lithuanian Standard specifies requirements for groats and flakes supplied to the

wholesale and retail trade.


Subsector : C01 Registration Date : 2017-08-07Organization : MSZTCountry : Hungary


ICS : 67.240, 67.240National Ref : MSZ 8761-4Title : Beer. Sensory analysis

Relatedness :National : REV/AMD MSZ 8761-4:1995

Subsector : C01 (Secondary Subsector)




ICS : 67.240, 67.240National Ref : MSZ 8761-4Title : Beer. Sensory analysis




ICS : 67.240, 67.240National Ref : MSZ 20501-2Title : Test methods for bakery products. Sensory analysis. Qualification on points


Page 15





ICS : 67.240, 67.240National Ref : MSZ 20501-2Title : Test methods for bakery products. Sensory analysis. Qualification on points




ICS : 67.240, 67.240National Ref : MSZ 5843-1Title : Sensory analysis of meat products. Part 1: Salami and sausages

Relatedness :National : REV/AMD MSZ-08-0943:1989





ICS : 67.240, 67.240National Ref : MSZ 5843-1Title : Sensory analysis of meat products. Part 1: Salami and sausages




ICS : 67.240, 67.240National Ref : MSZ 5843-2Title : Sensory analysis of meat products. Part 2: Cold cuts




Page 16



ICS : 67.240, 67.240National Ref : MSZ 5843-2Title : Sensory analysis of meat products. Part 2: Cold cuts




ICS : 67.240, 67.240National Ref : MSZ 5843-3Title : Sensory analysis of meat products. Part 3: Parisers, frankfurter, crinoline






ICS : 67.240, 67.240National Ref : MSZ 5843-3Title : Sensory analysis of meat products. Part 3: Parisers, frankfurter, crinoline



Subsector C02: PAINTS AND RELATED PRODUCTS

Subsector : C02 Registration Date : 2017-08-16Organization : DINCountry : Germany


ICS : 87.060.10National Ref : DIN 53236Title : Colouring materials - Conditions of measurement and evaluation for the determination of

colour differences for paint coatings, similar coatings and plastics


Page 17



ICS : 87.060.10National Ref : DIN 53163Title : Pigments and extenders - Determination of lightness of extenders and white pigments in

powder form



Subsector C04: LABORATORY GLASSWARE



ICS :National Ref : 05500149Title : Laboratory glassware; laboratory thermometers, scale values 0,1 °C, 0,2 °C and 0,5 °C




ICS :National Ref : 05500164Title : Laboratory glassware - Anschütz thermometer set




ICS :National Ref : 05500165Title : Laboratory glassware - laboratory thermometers, smallest scale division 1 °C and 2 °C


Page 18



ICS :National Ref : 05500166Title : Laboratory glassware - solid stem general purpose thermometers




ICS :National Ref : 05500167Title : Laboratory glassware - Density hydrometers - Part 1: General requirements




ICS :National Ref : 05500168Title : Laboratory glassware - hydrometers, principles of construction and adjustment



** End of Sector **




Sector F : FUNDAMENTAL STANDARDS


Page 20Subsector F05: MEASURING INSTRUMENTS

Subsector : F05 Registration Date : 2017-08-16Organization : EVSCountry : Estonia


ICS : 17.020, 17.060National Ref : prEVS 912Title : Non-automatic weighing instruments - Verification procedureScope : The scope of this Estonian Standard is verification of non-automatic weighing instruments

which comply to international requirements and are subject of verification in Estonia by verification authority. Standard sets requirements for equipment, verification procedure and principles of conformity decision making in compliance with relevant international normative acts.




ICS : 17.020, 17.060National Ref : prEVS 913Title : Fuel dispensers - Verification procedureScope : The scope of this Estonian Standard is verification of fuel dispensers which comply to

international requirements and are subject of verification in Estonia by verification authority. Standard sets requirements for equipment, verification procedure and principles of conformity decision making in compliance with relevant international normative acts.


Subsector : F05 Registration Date : 2017-08-31Organization : BSI Draft Issue Date : 2017-08-15Country : United Kingdom Latest Date for Comments : 2017-10-15

Project ID : 01702654/0001 Draft for public enquiry

ICS :National Ref : BS 8499:2017Title : Specification for domestic gas meter boxes and meter bracket



Subsector F15: MATERIAL TESTING IN GENERAL

Subsector : F15 Registration Date : 2017-08-21Organization : ASICountry : Austria

Page 21


ICS : 03.180, 19.100National Ref : ÖNORM M 3041Title : Training of personnel carrying out non-destructive testing (NDT personnel)Scope : This ÖNORM establishes a standardized system for the training of NDT personnel. It defines

the levels of competence of NDT personnel according to ÖNORM EN ISO 9712, UIC-Kodex 960 V, ÖNORM EN 4179 und NAS 410 as well as the level of training required for this purpose and the required knowledge and skills. The standardized and organized training of NDT personnel creates a basis for a successful access to examinations and certifications in accordance with ÖNORM EN ISO 9712, UIC-Kodex 960 V, ÖNORM EN 4179 und NAS 410. This ÖNORM deals with qualification as far as organized training at a recognized training centre and in-house-training is concerned. Depending on the requirements to be met by NDT personnel, this ÖNORM shall apply to NDT levels 1, 2 and 3.


Subsector : F15 Registration Date : 2017-08-16Organization : DINCountry : Germany


ICS :National Ref : 06235196Title : pH-measurement - pH-measurement of aqueous solutions with pH combination

electrodes with pH glass electrodes and evaluation of measurement uncertainty



Subsector F16: GRAPHICAL SYMBOLS



ICS :National Ref : 01700037Title : Printing technology - Type sizes - Part 2: Digital typesetting and related techniques



Subsector F20: QUALITY ASSURANCE

Subsector : F20 Registration Date : 2017-08-21Organization : ASICountry : AustriaProject ID : 00027194/0001 Project

Page 22

EstablishedICS : 03.120.10National Ref : ÖNORM ISO 10001Title : Quality management - Customer satisfaction - Guidelines for codes of conduct for

organizationsScope : This International Standard provides guidance for planning, designing, developing,

implementing, maintaining and improving customer satisfaction codes of conduct. This International Standard is applicable to productrelated codes containing promises made to customers by an organization concerning its behaviour. Such promises and related provisions are aimed at enhanced customer satisfaction. Annex A provides simplified examples of components of codes for different organizations.




ICS : 03.120.10National Ref : ÖNORM ISO 10002Title : Quality management systems - Customer satisfaction - Guidelines for complaints

handling in organizationsScope : This International Standard provides guidance on the process of complaints handling related

to products within an organization, including planning, design, operation, maintenance, and improvement. The complaints-handling process described is suitable for use as one of the processes of an overall quality management system. This International Standard is not applicable to disputes referred for resolution outside the organization or for employment-related disputes. It is also intended for use by organizations of all sizes and in all sectors. Annex A provides guidance specifically for small businesses. This International Standard addresses the following aspects of complaints handling: a) enhancing customer satisfaction by creating a customer-focused environment that is open to feedback (including complaints), resolving any complaints received, and enhancing the organization's ability to improve its product and customer service; b) top management involvement and commitment through adequate acquisition and deployment of resources, including personnel training; c) recognizing and addressing the needs and expectations of complainants; d) providing complainants with an open, effective, and easy-to-use complaints process; e) analysing and evaluating complaints in order to improve the product and customer service quality; f) auditing of the complaints-handling process; g) reviewing the effectiveness and efficiency of the complaints-handling process.




ICS : 03.120.10National Ref : ÖNORM ISO 10003Title : Quality management - Customer satisfaction - Guidelines for dispute resolution external

to organizations

Page 23

Scope : This International Standard provides guidance for an organization to plan, design, develop, operate, maintain and improve an effective and efficient dispute-resolution process for complaints that have not been resolved by the organization. This International Standard is applicable to: - complaints relating to the organization¿s products intended for, or required by, customers, the complaintshandling process or dispute-resolution process - resolution of disputes arising from domestic or cross-border business activities, including those arising from electronic commerce. This International Standard is intended for use by organizations regardless of type, size and product provided, and deals with - guidance on determining when and how organizations can participate in dispute resolution, - guidance on the selection of providers and use of their services, - top management involvement in, and commitment to, dispute resolution and deployment of adequate resources within the organization, - the essentials for fair, suitable, transparent and accessible dispute resolution, - guidance on management of an organization¿s participation in dispute resolution, and - monitoring, evaluating and improving the dispute-resolution process.




ICS : 03.120.10National Ref : ÖNORM ISO 10004Title : Quality management - Customer satisfaction - Guidelines for monitoring and measuringScope : This International Standard provides guidance in defining and implementing processes to

monitor and measure customer satisfaction. This International Standard is intended for use by organizations regardless of type, size or product provided. The focus of this International Standard is on customers external to the organization




ICS : 03.100.01, 03.100.40National Ref : ÖNORM ISO 21503Title : Project, programme and portfolio management - Guidance on programme managementScope : This International Standard provides guidance for programme management. This

International Standard is applicable to any type of organisation including public or private and any size organisation or sector, as well as any type of programme in terms of complexity, size or duration. This International Standard provides high-level descriptions of relevant terms, definitions, concepts, prerequisites and practices, including roles and responsibilities that form good practice in programme management. It does not provide guidance on processes, methods and tools.


Page 24** End of Subsector **

Subsector F21: VALUE ANALYSIS AND PROJECT NETWORK



ICS :03.060, 03.080, 91.040, 93.010

National Ref : prEVS 875-8Title : Property valuation - Part 8: Cost approachScope : The standard series EVS 875 applies to property valuation. These standards are to be used

for valuation activitises and using valuations. The users of these standards are real estate specialists, construction specialists, environment specialists, financial reporting specialists (accountants, auditors), credit institutions, higher edukation institutions. These standards create a basis for unified approach to property valuation, satisfying the needs of private and public sector. EVS 875-8 "Property valuation - Part 8: Cost approach" gives the objectives and possibilities of using the cost approach and covers the valuation of land and buildings.




ICS :03.060, 03.080, 91.040, 93.010

National Ref : prEVS 875-9Title : Property valuation - Part 9: Income ApproachScope : The series EVS 875 applies to property valuation. These standards are to be used for

valuation activities and for use of valuations. The users of these standards are real estate specialists, construction specialists, environment specialists, financial reporting specialists (accountants, auditors), credit institutions, higher education institutions. These standards create a basis for unified approach to property valuation, satisfying the needs of both the private and public sector. EVS 875-9 covers the usage of income approach when finding the market value, the value in use and the investment value and investment analysis.



Subsector F99: UNDETERMINED



ICS :National Ref : 15202694Title : Geometrical product specifications (GPS) - Mechanical dial gauges - Limits for

Page 25

metrological characteristics



** End of Sector **




Sector H : PRODUCTS FOR HOUSEHOLD AND LEISURE USE


Page 27Subsector H23: LADDERS

Subsector : H23 Registration Date : 2017-08-16Organization : DINCountry : Germany


ICS : 91.060.30National Ref : DIN 3193Title : Loft ladders - Special constructions for ceilings with a high thickness and for an increased

maximum total load



Subsector H26: SEALING MATERIALS



ICS :National Ref : 03200804Title : Sealing profiles of expanded PTFE for flanged joints in the gas supply




ICS : 75.100National Ref : DIN 3536Title : Lubricants for gas valves in indoor installation, gas distribution and gas transportation

pipe lines



Subsector H99: UNDETERMINED



ICS :National Ref : 04000354Title : Equipment for commercial kitchens - Refrigeration technology equipment - Part 1:

Page 28

Refrigerators and refrigerated counters; Requirements and testing





Cooling tray; Requirements and testing





Refrigerated display cases for food distribution; requirements and testing





Refrigerators and freezers; Requirements and testing




ICS :National Ref : 04000361Title : Equipment for commercial kitchens - Food distribution equipment - Part 2: Heated service

counters, Requirements and testing

Page 29




ICS :National Ref : 04000362Title : Equipment for commercial kitchens - Thermal equipment - Part 1: Warming cupboards -

Requirements and testing



** End of Sector **




Sector I : MECHANICAL ENGINEERING


Page 31Subsector I01: SCREW THREADS

Subsector : I01 Registration Date : 2017-08-16Organization : DINCountry : Germany


ICS :National Ref : 15202695Title : Geometrical product specifications (GPS) - Screw setting gauges for measuring

instruments for ISO metric screw threads; setting plug gauges and setting ring gauges from 1 mm to 100 mm nominal thread diameter



Subsector I02: FASTENERS



ICS :National Ref : 02600099Title : Springs - Measuring- and test statistic - Part 1: Cold formed cylindrical tension springs




ICS : 21.060.10National Ref : DIN 34825-1Title : Cylindrical head screws with inner contact flange - Part 1: Driving feature 12 point socket




ICS : 21.060.10National Ref : DIN 34805-1Title : Button head screws - Part 1: Driving feature hexalobular socket


Page 32



ICS : 21.060.10National Ref : DIN 34805-2Title : Button head screws - Part 2: Screws with collar and driving feature hexalobular socket




ICS :National Ref : 06702293Title : Adjusting rings




ICS :National Ref : 06702294Title : Internal drive pipe plugs - Conical thread




ICS :National Ref : 06702295Title : Internal drive screw plugs with collar - Cylindrical thread


Subsector : I02 Registration Date : 2017-08-16

Page 33

Organization : DINCountry : Germany


ICS :National Ref : 06702296Title : Hexagon head pipe plugs - Conical thread




ICS :National Ref : 06702297Title : Hexagon head screw plugs with collar - Cylindrical thread




ICS :National Ref : 06702298Title : Fasteners - Change of appearance of black surfaces



Subsector I05: IRON PIPES

Subsector : I05 Registration Date : 2017-08-07Organization : ASICountry : Austria


ICS : 93.020National Ref : ÖNORM B 2567Title : Piles of ductile iron - Dimensions, installation and quality assuranceScope : This ÖNORM sets forth the implementation characteristics, installation instructions,

structural conditions and quality assurance for piles made of ductile cast iron. The pile is used as a foundation element in structural engineering, civil engineering, industrial construction, pipeline construction, bridge construction and special applications. Examples here to are shown in Annex A.

Relatedness :

Page 34

National : New


Subsector I11: MACHINE TOOLS



ICS : 21.180National Ref : DIN 950Title : Handwheels, dished - Hub hole round or straigth square




ICS : 21.080National Ref : DIN 3670Title : Hand wheels, disc type



Subsector I13: GAS CONTAINERS



ICS : 23.020.30National Ref : ÖNORM M 7396Title : Transportable pressure vessels - Use of gas cylinder bundlesScope : This Austrian Standard is applicable to the operation of cylinder bundles for compressed and

liquefiedgasesandacetylene.For the transport of cylinder bundles, the relevant provisions for the transport of dangerous goods (e.g. ADR/RID), implemented in Austria by the Law on transport of dangerous goods - GGBG, BGBl. I Nr. 145/1998 as amended by BGBl. I Nr. 91/2013, shall be observed.



Subsector I17: MACHINERY IN GENERAL (INCLUDING SAFETY)

Page 35



ICS :National Ref : 15202700Title : Manufacturing processes - Terms and definitions, division



Subsector I18: MINING



ICS :National Ref : 00518073Title : Headgears and winding towers for mines - Design loads, calculating- and construction

principles



Subsector I19: NUCLEAR ENERGY



ICS : 11.040.60National Ref : ÖNORM S 5292-2Title : Medical remote-controlled automatically-driven afterloading systems - Part 2: Constancy

testing of functional performance characteristicsScope : This ÖNORM specifies the extent and execution of constancy testing of functional

performance characteristics of medical remote-controlled automatically-driven afterloading Systems.




ICS : 11.020, 17.240

Page 36

National Ref : ONORM S 5270-1Title : Dose calibrators - Part 1: Acceptance testingScope : This ÖNORM specifies the Implementation of acceptance testing of dose calibrators on site.

The ÖNORM contains parts of ÖNORM EN 61303 "Medical electrical equipment - Radionuclide calibrators - Particular methods for describing performance" that have to be considered for acceptance testing according Austrian "MedStrSchV".




ICS : 11.040.60National Ref : ÖNORM S 5292-3Title : Medical remote-controlled automatically-driven afterloading systems - Part 3: Rules for

testing of radiological protectionScope : This ÖNORM specifies the rules for testing of radiological protection for permission

procedure according "StrSchG"



Subsector I31: VALVES



ICS : 91.140.60National Ref : DIN 3476-1Title : Valves - Requirements and tests - Part 1: Protection against corrosion by epoxy coating

of coating powders (P) or liquid varnishes (F)


Subsector : I31 Registration Date : 2017-08-16Organization : DINCountry : GermanyProject ID : 00300666/0001 SplittingICS : 91.140.60National Ref : DIN 3476-2Title : Valves - Requirements and tests - Part 2: Protection against corrosion by duromer thick

coating



Page 37** End of Sector **




Sector M : METALLIC MATERIALS


Page 39Subsector M12: ALUMINIUM ORES

Subsector : M12 Registration Date : 2017-08-21Organization : ASICountry : Austria


ICS : 03.100, 03.120.10National Ref : ÖNORM ISO 10006Title : Quality management systems - Guidelines for quality management in projectsScope : This document gives guidance on the application of quality management in projects. It

applies to organizations working on projects of varying complexity, small or large, of short or long duration, being an individual project to being part of a programme or portfolio of projects, in different environments, and irrespective of the kind of product/service or process involved, with the intention of satisfying project interested parties (stakeholders) by introducing quality management in projects. This can necessitate some tailoring of the guidance to suit a particular project.



Subsector M15: METALLIC CORROSION

Subsector : M15 Registration Date : 2017-08-28Organization : UNICountry : Italy


ICS : 77.060, 93.020National Ref : UNI1603375Title : Cathodic protection of buried metallic structures - General criteria for the implementation,

verification and integration of ISO 15589-1 for cathodic protection systems or galvanic anodes.

Scope : The standard defines the annual programming of cathodic protection measures to be applied to current-operated systems or galvanic-anode systems, with the aim of monitoring theeffectivenessofcathodicprotectioninaccordancewithISO15589-1.The standard does not apply to cathodic protection systems of concrete reinforcement, nor toofcomplexstructuresinaccordancewithUNIEN14505.

Relatedness :National : REV/AMD UNI 11094:2004


Subsector M16: MECHANICAL TESTS FOR METALS

Subsector : M16 Registration Date : 2017-08-31Organization : BSICountry : United Kingdom


ICS :National Ref : BS 8571Title : Methodoftestfordeterminationoffracturetoughnessinmetallicmaterials

using single edge notched tension (SENT) specimens

Page 40



** End of Sector **




Sector N : NON-METALLIC MATERIALS


Page 42Subsector N03: PETROLEUM PRODUCTS

Subsector : N03 Registration Date : 2017-08-08Organization : SIST Draft Issue Date : 2017-09-01Country : Slovenia Latest Date for Comments : 2017-11-01


ICS : 75.160, 75.160National Ref : SIST EN 590:2013+A1:2017/oA101:2017Title : Automotive fuels - Diesel - Requirements and test methodsScope : The document specifies sampling procedures, compulsory equipping of diesel distribution

appliances with information plates or labels and requirements based on climate conditions in Slovenia.


Subsector : N03 Registration Date : 2017-08-08Organization : SIST Draft Issue Date : 2017-09-01Country : Slovenia Latest Date for Comments : 2017-11-01


ICS : 75.160, 75.160National Ref : SIST EN 228:2012+A1:2017/oA101:2017Title : Automotive fuels - Unleaded petrol - Requirements and test methodsScope : The document specifies sampling procedures, compulsory equipping of unleaded petrol

distribution appliances with information plates or labels, what are requirements of knock characteristics of unleaded petrol and requirements for evaporation behaviour in Slovenia.


Subsector : N03 Registration Date : 2017-08-07Organization : ASICountry : Austria


ICS : 75.160.20National Ref : ÖNORM EN 589/ATitle : Automotive fuels - LPG - Requirements and test methods (Amendment)Scope : Adaptation of the national Annex to the requirements laid down in the EN standard, which

are to be defined by a national Annex required by the EN standard.


Subsector : N03 Registration Date : 2017-08-18Organization : SIS Draft Issue Date : 2017-10-18Country : Sweden Latest Date for Comments : 2017-10-18


ICS : 75.160.20National Ref : 155410

Page 43

Title : Fuel oils - RequirementsScope : This standard includes requirements for fuel oils based on distillate (Eo1, Eo2 and Eo3A) as

well as residual fuel oils (Eo3B, Eo4, Eo5, Eo6). If fuel oil is used for other purposes than heating, additional requirements have to be considered. These requirements are not stated in this standard.


Subsector : N03 Registration Date : 2017-08-01Organization : TSECountry : Turkey

Project ID : tst11485/0002 Project Established

ICS : 75.100National Ref :Title : Lubricating oils, industrial lubricants and related products (Class L) - Group G: Gear oils -

Used in motor vehiclesScope : This standard specifies requirements and test methodsfor gear oils used im motor vehicles.



Subsector N14: PLASTICS PIPES

Subsector : N14 Registration Date : 2017-08-16Organization : DINCountry : Germany


ICS :National Ref : 11904249Title : Coverings for wells, spring water chambers and other water supply construction -

Principles for construction



** End of Sector **




Sector S : HEALTH, ENVIRONMENT AND MEDICAL EQUIPMENT


Page 45Subsector S01: ACOUSTICS AND SOUND INSULATION

Subsector : S01 Registration Date : 2017-08-28Organization : UNICountry : Italy


ICS : 91.120.20National Ref : UNI1603376Title : Internal acoustical characteristics of confined spaces – Design methods and evaluation

techniques - Part 1: General requirementsScope : The standard describes general aspects common to all areas of application, in details it

includes descriptors suitable to represent the room acoustical qualities with relation to the intendeduseoftheroom,referencevalues,specificpredictingandverificationmethodsThestandardisdedicatedtodifferentdestinationssuchas:1) school - communication / collective - collective - small conference rooms and / or multifunctionalwithalimitof250m³;2)healthsector/o;3)Offices,withparticularregardtoopenplanoffices4)restaurantsector;5)commercial-sporting-tertiarymanagementsector;6)production/industrialsector-fair-exhibition.




ICS : 91.120.20National Ref : UNI1603377Title : Internal acoustical characteristics of confined spaces – Design methods and evaluation

techniques - Part 2: SchooScope : The standard defines the acoustic descriptors suitable to represent the acoustic quality, and

reference values for the school - communicative / collective - collective - small conference and/orpolyfunctionalconferencerooms.For the prediction methods and the evaluation techniques, please refer to Part 1 of this Standard.



Subsector S04: PROTECTIVE CLOTHING AND EQUIPMENT

Subsector : S04 Registration Date : 2017-08-16Organization : DINCountry : Germany


Page 46

ICS : 13.340.60National Ref : DIN 19428Title : Personal fall protection equipment - Rope clamps and webbing clamps - Safety

requirements and test methods



Subsector S08: AIR QUALITY

Subsector : S08 Registration Date : 2017-08-01Organization : TSECountry : Turkey


ICS : 91.040.10National Ref :Title : HYGIENIC AIR CONDITIONING AND VENTILATION IN HOSPITALS - PREPARATION

OF THE PROJECTS, ACCEPTANCE OF THE SYSTEM, AND PERIODICAL MAINTENANCE

Scope : This standard covers requirements for preparation of the projects, system acceptance and periodical maintenance of hygienic air conditioning and ventilation systems in hospitals



Subsector S09: WATER QUALITY AND WATER SUPPLY



ICS : 13.060.20National Ref : DIN 3506Title : Water conditioning equipment inside buildings - Stonecatcher with a mesh size of 1,0 mm

to 1,5 mm - Requirements of construction and safety



Subsector S18: STERILIZATION OF EQUIPMENT



ICS : 11.080.01National Ref : UNI1603336Title : Reconditioning of medical devices - Guidelines for design, development and control of a

Page 47

reprocessingforreusablemedicaldevices(RMD)intendedtobeusedassterile.Scope : The Technical Report give guidelines for design, development, control and efficacy

evaluation of any single phase and of the entire re-process of reusable medical devices intendedtobeusedassterile.The document also includes organizational criteria concerning: responsibilities, environments, maintenance, routine controls, validation, documents, process review and traceability.Thesterilizationprocessesdescribedinthisdocumentare:-Saturatedsteamsterilizationwithforcedairremoval,-Vaporizedhydrogenperoxidewithorwithoutplasma,-Lowtemperaturesteamandformaldehyde,-ethyleneoxide.TheTechnicalReportdoesnotspecifysafetyandprotectionrequirementsforoperators.

Relatedness :National : REV/AMD UNI/TR 11408:2011


Subsector S27: WASTE - CHARACTERIZATION, TREATMENT AND STREAMS



ICS : 13.030.10National Ref : DIN 19902Title : Leaching of solids - On-site leaching test for determination of mobilizable inorganic

fractions


Subsector : S27 Registration Date : 2017-08-07Organization : MSZTCountry : Hungary


ICS : 13.060.30National Ref : MSZ 318-6Title : Analysis of sewage sludge. Determination of organic solvent extract


Subsector : S27 (Secondary Subsector)




ICS : 13.060.30

Page 48

National Ref : MSZ 318-6Title : Analysis of sewage sludge. Determination of organic solvent extract



Subsector S99: UNDETERMINED

Subsector : S99 Registration Date : 2017-08-07Organization : ASICountry : Austria


ICS :03.120.10, 65.020.20, 91.040.01

National Ref : ÖNORM L 1136Title : Outdoor vertical greeningScope : The present ÖNORM is to be used for planning, installation and maintenance of enduring

outdoor greening on vertical surfaces with or without ground connection.



** End of Sector **




Sector T : TRANSPORT, MECHANICAL HANDLING AND PACKAGING


Page 50Subsector T02: AEROSPACE

Subsector : T02 Registration Date : 2017-08-31Organization : BSICountry : United Kingdom


ICS :National Ref : BS 2SP 151-153:1979/Amd1Title : Specification for Unified alloy steel washers. Amendment




ICS :National Ref : BS 2SP 157-163:1979/Amd3Title : 161),BSL37(SP162)andDTD204(SP158and159)materials.

Amendment




ICS :National Ref : BS 4A112:1992/Amd1Title : Specificationforcadmium-platedsteelshearbolts(UnifiedhexagonsandUnified

threads). Amendment




ICS :National Ref : BS 2 Amd 3Title : Specificationfor100countersunkheadaluminiumalloybolts(Unifiedthreads)

for aircraft. Amendment


Page 51



ICS :National Ref : BS 3A 107:1962/Amd2Title : Specificationforaluminiumalloynuts(UnifiedhexagonsandUnifiedthreads)

(ordinary and slotted) for aircraft. Amendment




ICS :National Ref : BS SP 94Title : Specificationforbronzeoil-retainingbushesandthrustwashers.For

aircraft



Subsector T03: ROAD VEHICLES

Subsector : T03 Registration Date : 2017-08-23Organization : SNCountry : Norway


ICS : 43.080.99National Ref : NS 11060Title : Firetruck - Functional and technical requirments for fire trucksScope : This standard specifies requirements and guidelines for participants in the value chain to

ensure the necessary quality and efficient tendering processes related to planning, procurement and operation of firetrucks in public services.



Subsector T16: LIFTS & ESCALATORS

Subsector : T16 Registration Date : 2017-08-18Organization : SNCountry : Norway


ICS : 13.220.20

Page 52

National Ref : NS 3807Title : Evacuation of building using liftsScope : Technical rules to establish a safety sone in order to use lifts for emergency evacuation of

buildings using fire detection system.



Subsector T19: ROAD SAFETY

Subsector : T19 Registration Date : 2017-08-28Organization : SNV Draft Issue Date : 2017-08-24Country : Switzerland Latest Date for Comments : 2017-10-05


ICS : 93.080.30National Ref : prSN 640886Title : Construction sites; Signaling of construction sites on main and secondary roads



** End of Sector **

2011-06

List of non-electrotechnical subsectors

Sector A: Services

Subsector Title ISO/TC CEN/TC

reference reference

A01 Tourist services / 329; CEN/WS ETO

A02 Cleaning services / 328

A03 Postal services / 331

A04 Transportation services / 320; CEN/WS 016; CEN/WS SCUTUM

A05 Maintenance services / 319

A06 Building and construction services / 330

A07 Translation services /

A08 Funeral services / CEN/BT/TF 139

A09 Facility management / 348

A10 Services of Real Estate Agents / CEN/BT/TF 180; 373

A11 Security Services / CEN/BT/TF 167; 391; 384; 370; CEN/WS 044; CEN/CLC/TC 4

A12 Consultancy Services / 395; 381

A13 Expertise Services / 405

A14 Aesthetic Services / 403;409

A99 Undetermined / CEN/WS 002; CEN/WS 004; CEN/WS 037; CEN/WS 039; CEN/WS 041; CEN/WS 051; 375; 374; 376; 385; 404

Sector B: Building and construction


reference reference

B01 Fire protection 21 70; 72; 191; 192

B02 Structures 59; 98 166; 167; 250; 277; 346; 349; 284; 288; 297; 340

B03 Concrete 71 104; CEN/WS 009

B04 Cement 74; 77 51

B05 Fire tests 92 127

B06 Gypsum / 241

B07 Glass 160 129

B08 Doors and windows 162 33

B09 Thermal matters 163 88; 89; 371; CEN/BT WG 173; CEN/WS 036

B10 Timber structures 165 124

B11 Metal structures 167 135

B12 Masonry 179; 196 125; 246

B13 Solar energy 180 312

B14 Geotechnics 182 341; 396

B15 Sanitary appliances / 163; 7

B16 Taps / /

B17 Lighting equipment and lighting / 50; 169 application technology

B18 Scaffolding / 53

B19 Ceramic tiles 189 67

B20 Drainage equipment / 165

B21 Baths / /

B22 Wallcoverings / 99

B23 District heating / 107

B24 Auxiliary and handicraft work / /

B25 Gas distribution installation and / 234; 235; 282 related equipment

B26 Road building and maintenance / 178; 227

B27 Waterproofing materials / 128; 254; 361; 314

B28 Floor coverings 38/SC 12 134

B29 Aggregates / 154

B30 Floor and surfacing / 217; 303; 323; 390

B31 Heating systems in buildings / 228; 247

B32 Precast concrete products / 177; 229

B33 Building design 205 315; 325; 388

B34 Building and construction – Environmental aspect 350; 351

B99 Undetermined / /

Sector C: Chemicals, chemical engineering and food products


reference reference

C01 Food products 34 174; 275; 302; 360; 307; 327; 338; 387; CEN/WS 008; CEN/WS 018; CEN/WS 054

C02 Paints and related products 35 139; 298; 173

C03 Chemistry 47 317; 363

C04 Laboratory glassware 48 332

C05 Lac / /

C06 Essential oils 54 /

C08 Pesticides 81 /

C09 Surfactants 91 276

C10 Starch 93 /

C11 Tobacco 126 401

C12 Glass plant / /

C13 Fertilizers 134 223; 260

C16 Wood preservatives / /

C17 Trees and plants / /

C18 Adhesives / 193

C19 Chemical analysis 201; 202 382; 347

C20 Explosives and firework / 212; 321

C21 Cosmetics 217 392

C22 Bio-Based products / 411

C99 Undetermined / 386

Sector F: Fundamental standards


reference reference

F01 Technical drawings 10 /

F02 Units & symbols 12 /

F03 Preferred numbers 19 /

F04 Sieves 24 /

F05 Measuring instruments 30; 113 92; 171; 176; 237;

294; 318; 244; 367; 141; CEN/WS 011

F06 Terminology principles 37 /

F07 Documentation and information 46 304; CEN/WS 024 CEN/WS 010 CEN/WS 023 CEN/WS 028 CEN/WS 014 CEN/WS 050 CEN/WS 006 368

F08 Surfaces / 290

F09 Banking 68 /

F10 Statistics 69 /

F12 Information processing systems 204 224; 225; 251; 278; CEN/WS CPF CEN/WS CIS CEN/WS ODR CEN/WS CID 287; 311; 365

F13 Environmental tests / /

F14 Graphical technology, 130 / sign-boards and nameplates

F15 Material testing in general 135 138; CEN/WS 007 CEN/WS 021 CEN/WS 033

F16 Graphical symbols 145 /

F17 Administrative documents 154 CEN/WS MMU

F18 Micrographics 171 /

F19 Optics 172; 187 123; 170

F20 Quality assurance 176 CEN/CLC/TC1 CEN/CLC/WG QS CEN/WS 030 362

F21 Value analysis and project / 279 network

F22 Logistics / 379; 273

F23 Energy 203 CEN/CLC/JWG 1; CEN/CLC/JWG 2;

CEN/CLC/JWG 3; CEN/CLC/JWG 4; CEN/WS 027

F99 Undetermined / 389; CEN/WS 057; CEN/WS 058; CEN/WS 060

Sector H: Products for household and leisure use


reference reference

H01 Cinematography 36 372

H02 Photography 42 /

H03 Consumer questions / 291

H04 Sports equipment 83 136

H05 Oil and gas burners / 47; 131

H06 Horology 114 /

H07 Space heating 116 62; 110; 130; 179; 180

H08 Sizing systems 133; 137 /

H09 Furniture 136 207

H10 Sewing machines 148 /

H11 Heater controls 161 58

H12 Ceramic and glass-ware for food 166 /

H13 Jewellery 174 CEN/WS 047

H14 Caravans 177 245

H15 Toys 181 52

H17 Oil stoves / 46

H18 Central heating boilers / 48; 57; 109; 269

H19 Non-electric cookers and barbecues / 49; 281; 295

H22 Smokers’ lighters and matches / 355; 87

H23 Ladders / 93

H24 Tactile danger warnings / /

H25 Large gas appliances / 106; CEN/CLC/JWG FCGA

H26 Sealing materials / 108; 208

H27 Educational equipment / /

H28 Hunting 191 /

H29 Heat pumps / 113

H30 Equipment for children / 252

H31 Dedicated LPG appliances / 181

H32 Culinary utensils 186 194

H33 Footwear (excluding protective / 309 footwear)

H34 Child safety / CEN/BT/WG 117 398

H99 Undetermined / 299; 364; 369; 402

Sector I: Mechanical engineering


reference reference

I01 Screw threads 1 /

I02 Fasteners 2 185

I03 Limits & fits / /

I04 Rolling bearings 4 /

I05 Iron pipes 5 203

I06 Pressure vessels 11 54

I07 Shafts 14 /

I08 Agricultural machines 23 144, 334

I09 Small tools 29 213

I10 Splines / /

I11 Machine tools 39 142; 143; 145; 255

I12 Pulleys & belts 41 188

I13 Gas containers 58 23; 286

I14 Gears 60 /

I15 Equipment for petroleum industry 67 12

I16 Internal combustion engines 70; 192 270

I17 Machinery in general 72; 199 114; 153; 214; 313 (including safety) 271, 337; 399; 397 CEN/WS 025

I18 Mining 82 196

I19 Nuclear energy 85 /

I20 Refrigeration 86 44; 182

I21 Chains and chain wheels 100 /

I22 Vacuum technology 112 /

I23 Pumps 115 197

I24 Industrial fans 117 356

I25 Compressors 118 232

I26 Plain bearings 123 /

I27 Earth moving and construction 127; 195 151 equipment

I28 Fluid power 131 /

I29 Gas cleaning / 195

I30 Air distribution / 156

I31 Valves 153; 185 69; 236; 105

I32 Flanges / 74

I33 Information processing in 184 310 automation

I34 Non-ferrous metallic pipes / /

I35 Leisure and recreational machines / 152

I36 Thermoprocessing technology / 186

I37 Printing and paper machines / 198

I38 Leather production, tannery and / 200; 201 related machinery

I39 Machines for metal processing / 202; 322

I40 Industrial piping networks / 267

I41 Membrane filters / 272

I42 Potentially explosive atmospheres / 305

I43 Hydrogen energy 197 /

I44 Nanotechnologies 229 352

I99 Undetermined / CEN/CLC/JTF PE; CEN/CLC/TC 2; 65, 157; CEN/WS 059

Sector M: Metallic materials


reference reference

M01 Steel 17 CEN/TC 342; 344; ECISS/TC 6 ECISS/TC 7 ECISS/TC 9 ECISS/TC 10 ECISS/TC 11 ECISS/TC 12 ECISS/TC 13 ECISS/TC 15 ECISS/TC 19 ECISS/TC 20 ECISS/TC 21 ECISS/TC 22 ECISS/TC 23 ECISS/TC 24 ECISS/TC 26 ECISS/TC 27 ECISS/TC 28 ECISS/TC 29 ECISS/TC 5 ECISS/TC 14 ECISS/TC 100 ECISS/TC 102 ECISS/TC 103 ECISS/TC 104 ECISS/TC 105 ECISS/TC 106 ECISS/TC 107 ECISS/TC 108 ECISS/TC 109 ECISS/TC 110

M02 Zinc / 209

M03 Foundry technology, 25 190; ECISS/TC 31 ECISS/TC 111 including cast iron

M04 Copper 26 133

M05 Welding 44 121

M06 Dimensions of wrought products / /

M07 Manganese and chromium 65 /

M08 Light alloys 79 132

M09 Iron ores 102 /

M10 Metallic coatings 107 240

M11 Powder metallurgy 119 /

M12 Aluminium ores 129 /

M13 Ferroalloys 132 /

M14 Nickel 155 /

M15 Metallic corrosion 156 262; 219

M16 Mechanical tests for metals 164 ECISS/TC 1 ECISS/TC 2 ECISS/TC 101

M17 Heavy metal ores 183 /

M18 Metal wire products / ECISS/TC 30; CEN/BT/TF 196; 378; 407

M20 Tin and tin alloys / 220

M21 Precious metals / 283

M22 Lead and lead alloys / 306

M99 Undetermined / /

Sector N: Non-metallic materials


reference reference

N01 Paper and board 6 172

N02 Solid fuels 27 335; 343;383; CEN/WS 019

N03 Petroleum products 28 19; 336; CEN/WS 038; CEN/WS 061

N04 Refractories 33 187

N05 Textiles 38 189; 248

N06 Rubber 45 218; 366 CEN/WS 003

N07 Sawn timber 55 38; 175

N08 Mica / /

N09 Plastics 61 249

N10 Cork 87 /

N11 Wood-based panels 89 112

N12 Timber products 99 /

N13 Leather 120 289

N14 Plastics pipes 138 155

N17 Fluorspar 175 /

N18 Glass-fibre reinforced plastics / /

N19 Tapes / 253

N20 Ceramics 206 184

N21 Gaseous fuels and combustible gas 158; 193 238; 408

N22 Feather and related materials / 222

N23 Diamond / 410

N99 Undetermined / /

Sector S: Health, environment and medical equipment


reference reference

S01 Acoustics and sound 43 126; 211 insulation

S02 Transfusion equipment 76 /

S03 Syringes 84 /

S04 Protective clothing and equipment 94 85; 158; 159; 160; 161; 162; CEN/WS 026; CEN/WS 043

S05 Dentistry 106 55

S06 Vibration & shock 108 231

S07 Anaesthetic and respiratory 121 215 equipment

S08 Air quality 146 137; 243; 264; CEN/CLC/JWG CMI

S09 Water quality and water supply 147 164; 230; CEN/WS 001 CEN/WS 034

S10 Surgical implants 150 285; CEN/CLC/JWG AIMD

S11 Contraceptives 157 /

S12 Gas analysis / /

S13 Ergonomics 159 122

S14 Prosthetics 168 /

S15 Surgical instruments 170 /

S16 Aids for the disabled 173 293

S17 Respiratory protective devices / 79

S18 Sterilization of equipment 198 102; 204

S19 First aid equipment and rescue systems / 239

S20 Waste collection, handling and / 183 transportation

S21 Laboratory medicine, clinical 194 140; 206; 233; pathology and biosafety 257; 258; 316; CEN/CLC/TC 3; CEN/WS 031; CEN/WS 053; CEN/WS 055

S22 Energy saving / CEN/WS 005 CEN/WS 015

S23 Personal & property protection against aggression/Burglary protection / 263

S24 Soil quality 190 345; CEN/WS 032

S25 Chemical disinfectants and / 216 antiseptics

S26 Environmental management 207 CEN/TC 406; CEN/WS 040

S27 Waste - Characterization, treatment / 292; 308; and streams CEN/BT/TF 120

S28 Demining / CEN/WS 029 CEN/WS 013

S99 Undetermined / 205; CEN/BT/TF 127 394; 259; 357; 358; 359; 380; 400; CEN/WS PCEC CEN/WS 012 CEN/WS 020

Sector T: Transport, mechanical handling and packaging


reference reference

T01 Shipbuilding and maritime 8; 188 15; 300 structures

T02 Aerospace 20 274; AECMA; ECSS ;377

T03 Road vehicles 22 301; 326 CEN/WS IMA

T04 Tyres 31 /

T05 Pallets 51 /

T06 Metal and plastic containers 52 210; 221; 265; 266; 268; 296 393

T07 Glass containers 63 /

T08 Cranes 96 147

T09 Materials handling and 101 148; 149 storage equipment

T10 Freight containers 104 119; 280

T11 Steel wire ropes 105 /

T12 Industrial trucks 110 150; 324

T13 Lifting chains, hooks and ropes 111 168

T14 Packaging 122 261; 120

T15 Cycles 149 333

T16 Lifts & escalators 178 10; 242

T17 Builders hoists / /

T18 Elevating platforms / 98

T19 Road safety / 226; 339

T20 Tram- and railway engineering / 256; / CEN/CLC/WG FPR

T21 Packaging machines / 146

T22 Off-road vehicles / 354

T99 Undetermined / CEN/WS TAF

Sector Z: Information technology


Z01 Radiocommunication for IT / /

Z02 Telephony, telegraphy for IT / CEN/CLC - ETSI

Z03 Common O.S.I. activities / CEN/CLC - EWOS

Z99 Undetermined / 353; CEN/WS ADN; CEN/WS AUT; CEN/WS BII; CEN/WS CAT; CEN/WS CST; CEN/WS CTC; CEN/WS DFA; CEN/WS DIR; CEN/WS DIS; CEN/WS DPA; CEN/WS DPP; CEN/WS EBE; CEN/WS ECH; CEN/WS ECO; CEN/WS EFI; CEN/WS EMD; CEN/WS ESI; CEN/WS ESR; CEN/WS EUR; CEN/WS FAS; CEN/WS FIN; CEN/WS FS2; CEN/WS FUN; CEN/WS GEN; CEN/WS HIC; CEN/WS ICT; CEN/WS IEC; CEN/WS IHM; CEN/WS INV2; CEN/WS ISD; CEN/WS JXF; CEN/WS KMA; CEN/WS LCT; CEN/WS LTS; CEN/WS MDC; CEN/WS MEE; CEN/WS MES; CEN/WS MET; CEN/WS MLX; CEN/WS MMI; CEN/WS NEA; CEN/WS NOM; CEN/WS ORC; CEN/WS POR; CEN/WS QIS; CEN/WS SAN; CEN/WS SCE; CEN/WS TEX; CEN/WS TWE; CEN/WS UDP; CEN/WS URI; CEN/WS WAC;

CEN/WS XFS; CEN/WS XML; CEN/WS eGo; CEN/WS eIN; CEN/WS ePR









Sector A : SERVICES


Page 3Subsector A02: CLEANING SERVICES

Subsector : A02 Registration Date : 2017-09-21Organization : SFS Draft Issue Date : 2017-08-15Country : Finland Latest Date for Comments : 2017-10-15

Project ID : 0000E471/0001 Draft for public enquiry

ICS :National Ref :Title : Cleaningquality.Systemforestablishingandassessingcleaningquality

Relatedness :National : REV/AMD SFS 5994


Subsector A09: FACILITY MANAGEMENT



ICS :National Ref :Title : Educational organizations -- Management systems for educational organizations --

Requirements with guidance for use






ICS :National Ref :Title : Safe working on lifts

Relatedness :National : REV/AMD SFS 5880


** End of Sector **









ICS : 13.220.50, 91.140.30National Ref : ÖNORM H 6034Title : Ventilation and air conditioning systems - Requirements for function tests at interface

control units of fire dampers and smoke control dampers under thermal loadScope : This ÖNORM defines unified test requirements interface for control units of fire dampers

according to ÖNORM EN 15650 and smoke control dampers according to ÖNORM EN 12101-8. It does not specify other fire control systems that are activated by the fire alarm System, i.e. according to ÖNORM F 3001.


Subsector : B01 Registration Date : 2017-09-07Organization : NENCountry : Netherlands


ICS : 13.220.50National Ref : NEN 6075+C1:2012/A1 Concept nlTitle : Determination of the resistance to smoke movement between spacesScope : Determination of the resistance to smoke movement of partitions. Application: all partition

walls. NEN 6075+C1/A1 contains amendments.




Subsector : B02 Registration Date : 2017-09-08Organization : BASCountry : Bosnia and Herzegovina


ICS : 91.010.30National Ref : pnBAS EN 1991-1-2/NA:2017Title : Eurocode 1: Actions on structures - Part 1-2: General actions - Actions on structures

exposed to fire - National annexScope : This document defines the value of national parameters or certain procedures for the

calculation with the standard BAS EN 1991-1-2:2015 and applied together with that standard.



Page 6


ICS : 23.040.01, 91.140.80National Ref : NEN 3215:2011/A1:2017 Concept nlTitle : Drainage system inside and outside buildings - Determination methods for drainage

capacity, water and air density and distance for roof mounted outletsScope : NEN 3215:2011/A1:2017 amends NEN 3215:2011.


Subsector : B02 Registration Date : 2017-09-11Organization : UNECountry : Spain Latest Date for Comments : 2017-10-21

Project ID : P0048374/0001 Draft for public enquiry

ICS :National Ref : PNE-EN 1998-1:2011/1MTitle : Eurocode 8: Design of structures for earthquake resistance - Part 1: General rules,

seismic actions and rules for buildings. 1st Amendment: National annexScope : This modification includes the national annex of UNE-EN 1998-1, establishing the nationally

determined parameters, some non-contradictory complementary information and the status of informative annexes.

Relatedness :National : REV/AMD UNE-EN 1998-1:2011, UNE-EN 1998-1:2011/A1:2013



ICS :National Ref : PNE-EN 1998-2:2012/1M Title : Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges. 1st

Amendment: National annexScope : This modification includes the national annex of UNE-EN 1998-2, establishing the nationally


Relatedness :National : REV/AMD UNE-EN 1998-2:2012



ICS :National Ref : PNE-EN 1998-3:2012/1MTitle : Eurocode 8: Design of structures for earthquake resistance - Part 3: Assessment and

retrofitting of buildings.1st Amendment: National annexScope : This modification includes the national annex of UNE-EN 1998-3, establishing the nationally

determined parameters, some non-contradictory complementary information and the status

Page 7

of informative annexes.




ICS :National Ref : PNE-EN 1998-5:2011/1MTitle : Eurocode 8: Design of structures for earthquake resistance Part 5: Foundations, retaining

structures and geotechnical aspects.1st Amendment: National annexScope : This modification includes the national annex of UNE-EN 1998-5, establishing the nationally




Subsector B04: CEMENT



ICS :National Ref : PNE 80303-2Title : Cements with additional characteristics. Part 2: Sea water resisting cements.Scope : This draft standard revises the current version of sea water resisting cements standard trying

to align the text with the requirements established in the harmonized product standards of cement used. Therefore, it specifies additional requirements to be fulfilled by the corresponding cements complying with EN 197-1, EN 197-4 and EN 14216 to be considered waterresistingcementsaswellastheconformitycriteria.The above cited cements complying with the European related standards should be CE marked.

Relatedness :National : REV/AMD UNE 80303-2:2011



ICS :National Ref : PNE 80303-1Title : Cements with additional characteristics. Part 1: Sulphate resisting cements.Scope : This draft standard revises the current version of sulphate resisting cements standard trying

to align the text with the requirements established in the harmonized product standards of

Page 8

cement used. Therefore, it specifies additional requirements to be fulfilled by the corresponding cements complying with EN 197-1 and EN 14216 to be considered sulphate resisting cements as well as the conformity criteria. Moreover, these cements have the same, even stricter, requirements than sea water resisting cements and therefore a cement designated as sulphate resisting cement should also be considered as sea water resisting cementsalthoughnotonthecontrary.

Relatedness :National : REV/AMD UNE 80303-1:2013


Subsector B08: DOORS AND WINDOWS

Subsector : B08 Registration Date : 2017-09-04Organization : UNMZ Draft Issue Date : 2017-11-30Country : Czech Republic Latest Date for Comments : 2017-12-30


ICS :National Ref :Title : Pleated peripheral walling of buildings - Requirements for installation, control accuracy

and appearance checkScope : The aim of the new standard are Requirements for installation Pleated peripheral walling of

buildings

Relatedness :National : REV/AMDČSNP747251(2015)



ICS :National Ref :Title : Curtain walling - Installation requirement, accuracy and appearance checkScope : The aim of the new standard are Requirements for installation Curtain walling -

Watertightnessandappearancecheck

Relatedness :National : REV/AMDČSNP747250(2014)



ICS :National Ref :Title : Windows and external pedestrian doorsets – Requirements for instalationScope : The aim of the revision is obsolete document for instalation windows and external

pedestrian doorsets

Page 9

Relatedness :National : REV/AMDČSN746077(2014)

Subsector : B08 Registration Date : 2017-09-08Organization : NBNCountry : Belgium

Project ID : BE664045/0001 Project Established

ICS : 91.060.50National Ref : prNBN B 25-002-1:2017Title : External window work - Part 1 - Generalities

Relatedness :National : REV/AMD NBN B 25-002-1:2009


Subsector B09: THERMAL MATTERS



ICS : 91.120.10National Ref : ÖNORM H 6040Title : Calculation of the sensible and latent cooling load as well as of the internal temperature

evolution of rooms and buildings in summer (National specifications to ÖNORM EN ISO 52016 und ÖNORM EN ISO 52017)

Scope : As national amendment to ÖNORM EN ISO 52016 und ÖNORM EN ISO 52017, the present Standard specifies the calculation method for the determination of the cooling load (sensible and latent) of rooms and buildings as well as of the temperature evolution inside rooms in case of limited cooling performance under non-stationary edge conditions. As national amendment to ÖNORM EN ISO 13791, this Standard defines the calculation method for the determination of room temperature evolution (air and operative) without cooling system under non-stationary edge conditions.






ICS : 17.180.20, 91.160.01National Ref : UNI1603513Title : Lighting designe of pedestrian crossings in roads with motorized traffic.Scope : The technical specification provides guidelines and requirements for the design of road

study the study area for pedestrian crossings in motorized traffic carriage considering the

Page 10

lighting sistems and within the scope and at integration of the UNI 11248.






ICS : 23.040.70, 97.040.20National Ref : UNI1603538Title : Non-metallic flexible hoses for gas appliances for domestic and similar use Scope : This Standard defines the design requirements and test methods for non-metallic flexible

hoses for gas appliances for domestic and similar use with a nominal heat input up to 35 kW, using combustible gas of I, II, III families according to EN 437 and LPG at high pressure for theconnectionofLPGbottletopressureregulators.Thisstandardspecifiestwoclassesdependingontheoperatingpressure:- flexible hoses with a length specified by the manufacturer (type A1 e A2) for movable appliancesonly;-assembledflexiblehoses(typeBandC):forfittedandmovableappliances.These hoses can be installed in domestic premises and in external parts of buildings within a rangeoftemperaturesbetween-30°Cto90°C




ICS : 91.140.40National Ref : NPR 3378-22:2017 Concept nlTitle : Guidelines for NEN 1078 - Section gas appliances and appliance spaces - Part 22:

Installation spaces of gas appliances, appliance rooms and boiler rooms - Guidelines for NEN 1078 and NEN 3028

Scope : NPR 3378-22 gives gidelines for installation spaces of gas appliances, appliance rooms and boiler rooms.




ICS : 91.140.40National Ref : NPR 3378-5:2017 Concept nl

Page 11

Title : Guidelines for gas installations - Section gas pipework - Part 5: Gas pipework - Installation general - Guidelines for NEN 1078 and NEN 8078

Scope : This part applies to clauses 5.2, 5.7 and 5.8 of NEN 1078 and NEN 8078:2004.






ICS : 93.080.01National Ref : prSN 640026Title : Project processing and project phases in road construction

Relatedness :National : REV/AMD SN 640026:2012


Subsector B34: BUILDING AND CONSTRUCTION ENVIRONMENTAL ASPECTS



ICS : 93.080.99National Ref : prSN 640577Title : Protection of trees

Relatedness :National : REV/AMD SN 640577a:2003



Subsector : B99 Registration Date : 2017-09-28Organization : EVSCountry : Estonia


ICS : 91.100.15National Ref : prEVS 927Title : Burnt shale for building materials - Specification, performance and conformityScope : This standard gives a specification for burnt shale, which is produced from the combustion

of pulverized oil shale in energy generation plants, followed by dry separation of produced fine dispersed mineral particles. Burnt shale consists of clinker minerals, quicklime, dehydrated calcium sulphate, glass phase and insoluble residue. There are three types of burnt shale, which confirm to this standard: 1. burnt shale, separated by electric filters, for

Page 12

production of cement - burnt shale for cement; 2. burnt shale, separated by cyclone filters, for production of aerated concrete - burnt shale for aerated concrete; 3. burnt shale, separated by textile filters, for production of concrete - burnt shale for concrete. This standard defines the characteristics, test methods and evaluation of conformity of burnt shale.




ICS : 93.080.30National Ref : NEN 3381:2017 Concept nlTitle : Road traffic signs - Additional requirements for fixed traffic signsScope : NEN 3381 contains requirements, classification and test methods for traffic signs.




ICS : 91.140.01National Ref : prSIA 2056Title : Electricityinbuildings-

Energy and performance requirements

Relatedness :National : REV/AMD SIA 380-4:2006


** End of Sector **







Subsector : C01 Registration Date : 2017-09-15Organization : TSECountry : Turkey


ICS : 67.120.10National Ref :Title : Canned rosto- Ready to serve Scope : This standard cotains canned rosto – ready to serve.




ICS : 67.080.20National Ref :Title : Canned Green Beans With Meat-Ready To ServeScope : This standard applies to canned green beans with meat which is ready to serve.




ICS : 67.060National Ref :Title : Canned Chick-Peas-Ready to ServeScope : This standard comprise canned Chick-Peas-Ready to Serve




ICS : 67.060National Ref :Title : Canned Chick-Peas Stewed With Meat-Ready to Serve Scope : This standard applies to canned chick-peas stewed with meat which is ready to serve.


Page 15



ICS : 67.080.10National Ref :Title : Rose JamScope : This Standard contains the rose jams manufactured by using fruit of rose (Rose domescena

M.) and does not contain special rose jam manufactured for diet.




ICS : 67.180.10National Ref :Title : Jelly Candy Scope : This standard covers jelly candy, it does not cover ready jelly mix




ICS : 67.080.20National Ref :Title : Canned eggplant kebap -Ready to serve Scope : This standard specifies "Canned eggplant kebap -Ready to serve" which is ready to serve.



Subsector C04: LABORATORY GLASSWARE

Subsector : C04 Registration Date : 2017-09-28Organization : UNICountry : Italy


ICS : 71.040.10National Ref : UNI1603496

Page 16

Title : Fume cupboards for chemical handling. Limit values for containment, face velocity and air exchange efficiency

Scope : This standard contains the performance specifications required for fume cupboards to be used in the handling of chemicals in industrial, research and teaching activities, in particular theacceptabilitylimitvaluesfor:•Containmentandrobustnessofcontainment•facevelocity•airexchangeefficiency.Definitions of the methodologies and procedures for conducting the test of the above requirementscanbefoundinUNIEN14175-Part3.Additional requirements may be sought-after, for special use fume cupboards (e.g. those used in continuous processes); requirements that have to be specified case by case dependingonthespecifictypeofuse.This specification does not apply to ventilated cabinets



Subsector C21: COSMETICS

Subsector : C21 Registration Date : 2017-09-18Organization : UNECountry : Spain Latest Date for Comments : 2017-10-28


ICS :National Ref : PNE 84679Title : Cosmetic raw materials. Plant extracts. Determination of oleuropein content in olive leaf

extracts by liquid chromatography.Scope : This standard defines the procedure for the determination of oleuropein content by HPLC

in olive leaf plant extracts, for use in cosmetics

Relatedness :National : REV/AMD UNE 84679:2008


Subsector C22: BIO-BASED PRODUCTS

Subsector : C22 Registration Date : 2017-09-21Organization : SNCountry : Norway


ICS : 67.120National Ref : NS 9415Title : Marine fish farms – Requirements for site survey, risk analyses, design, dimensioning,

production, installation and operation Scope : The aim of the standard is to reduce the escape of fish from marine fish farms in Norway.

The standard will give requirements and recommendations for planning, production and operation of fish farms. The requirements will cover all main components as net bag, mooring, float collar, fleet as well as the interactions between main components and overall functionality.

Relatedness :

Page 17

National : New


Subsector C99: UNDETERMINED

Subsector : C99 Registration Date : 2017-09-07Organization : NENCountry : Netherlands


ICS : 07.100.01National Ref : NEN 8771:20117 Concept nlTitle : Design, operations and maintenance of biogas installations Scope : NEN 8770 describes requirements for the design, management, maintenance of biogas

installations with focus on the safety, environment and quality.




ICS :National Ref : PNE 315500Title : Supplies used in organic crop production. Products for pest and disease management.Scope : This standard establishes requirements for pesticides and phytosanitary products used for

pests and diseases control in plant production, suitable for organic agriculture, in accordancewithlegislationinforce.This standard is not applicable for biodynamic preparations although these are authorised in organicagriculture,becausetheyaredirectlypreparedbythefarmerintheirfarms.This standard is not applicable to post-harvest products.




ICS :National Ref : PNE 142500Title : Supplies used in organic crop production. Fertilizers and liming materials.Scope : This standard establishes requirements for fertilizers and liming materials used in plant

production,suitablefororganicagriculture,inaccordancewithlegislationinforce.



Page 18** End of Sector **






Page 20Subsector F12: INFORMATION PROCESSING SYSTEMS

Subsector : F12 Registration Date : 2017-09-11Organization : UNECountry : Spain Latest Date for Comments : 2017-10-21


ICS :National Ref : PNE 148004Title : Geographic Information - Open geographic dataScope : This International Standard establishes a standard definition of what shall be understood as

open geographic data and defines a set of requirements for publishing a set of geographic data in such a way as to be open geographic data.






ICS :National Ref : PNE 66500Title : Minimum requirements for the certification of supplies used in in organic crop production

according to UNE 142500 and UNE 315500Scope : This standard defines the minimum requirements for bodies providing certification of those

responsibles of placing in the market supplies used in organic crop production according to UNE 142500 and/or UNE 315500



** End of Sector **






Page 22Subsector H04: SPORTS EQUIPMENT

Subsector : H04 Registration Date : 2017-09-20Organization : ASICountry : Austria


ICS : 13.060.25, 97.220.10National Ref : ÖNORM M 5872Title : Equipment of water treatment plants for swimming pools with measuring and control

instrumentsScope : This Austrian Standard defines the use of manual and automated measurement and control

equipment for spa baths that are subject to the Austrian Baederhygieneverordnung.



Subsector H09: FURNITURE



ICS : 97.140National Ref : ÖNORM A 1610-2Title : Furniture - Requirements - Part 2: Dimensions, areas required, spacingsScope : This Austrian Standard includes specifications concerning dimensions and position areas for

planning and furnishing in the field of dwelling, office and object equipment as well as the required movement areas and distances. Furthermore, this ÖNORM offers assistance for the footprint planning of rooms.



Subsector H99: UNDETERMINED



ICS :13.060.10, 13.060.25, 97.220.10

National Ref : ÖNORM M 6230/ATitle : Bathing waters - Requirements for water quality, analysis and assessmentScope : The Austrian Standard ÖNORM M 6230 describes basic principles for the evaluation of

waterbodies in terms of their qualification for swimming and bathing, and provides further guidance for the investigation, evaluation and management of man-made bathing water.



** End of Sector **






Page 25Subsector I08: AGRICULTURAL MACHINES

Subsector : I08 Registration Date : 2017-09-11Organization : UNECountry : Spain Latest Date for Comments : 2017-10-11


ICS :National Ref : PNE 68072Title : Irrigation equipment. Rotating sprinklers. Design and operation requirementsScope : This standard specifies the requirements for design and operation of sprinklers used in

agricultural irrigation, as well as their test methods.



Subsector I15: EQUIPMENT FOR PETROLEUM INDUSTRY

Subsector : I15 Registration Date : 2017-09-21Organization : SFS Draft Issue Date : 2017-08-17Country : Finland Latest Date for Comments : 2017-10-18


ICS :National Ref :Title : SFS3352Servicestationforflammableliquids

Annex C (normative) Above ground tanks and equipments for petrol and ethanolfuel


Subsector : I15 Registration Date : 2017-09-21Organization : SFS Draft Issue Date : 2017-08-17Country : Finland Latest Date for Comments : 2017-10-18


ICS :National Ref :Title : SFS 3352 Service station for fammable liquids Appendix D Electrical equipments in

service station. Installation, inspection, documents and service and maintenance




ICS : 23.040.99National Ref : ÖNORM M 7325Title : Scraper traps for pressure pipelinesScope : This Austrian Standard includes requirements for pig traps serving for the insertion and

Page 26

extractionofpig.Pigsareusedfor-cleaning(e.g.bybrushesorscrapers)-separationofdifferentconveyorfluids-testingofthepipe(e.g.bycalibrationpigs)or-otherpurposes.ThedesignofthepigsthemselvesisnotspecifiedinthisÖNORM.All pressures mentioned are excessive pressures.



** End of Sector **






Page 28Subsector M08: LIGHT ALLOYS

Subsector : M08 Registration Date : 2017-09-11Organization : UNECountry : Spain Latest Date for Comments : 2017-10-21


ICS :National Ref : PNE 38019Title : Anodizing of aluminium and its alloys. Vocabulary.Scope : This standard defines the terms that concern anodized aluminium. An index of equivalent

English, French, German and Italian terms is included as an annex.



** End of Sector **






Page 30Subsector N05: TEXTILES

Subsector : N05 Registration Date : 2017-09-18Organization : UNECountry : Spain Latest Date for Comments : 2017-10-28


ICS :National Ref : PNE 40607Title : Agrotextiles. Determination of the geometric uniformity of the woven fabrics with

monofilamentsScope : This standard establishes a method for quantify the geometric uniformity of the agrotextiles

since the point of view of its geometry. The geometric parameters valued can be measured usingimagesobtainedbyadevicethatincorporatedadigitalcamera.Thisstandardappliestotheagrotextileofweftandwarpmadewithmonofilaments.



Subsector N09: PLASTICS

Subsector : N09 (Secondary Subsector)




ICS : 23.040.01, 83.080.01National Ref : UNI1603537Title : Durability of the products and of the systems made of plastic materials - Guidelines for

thedeterminationsoftheassessmentmethodsandtherelatedtestsScope : The technical report has been drafted to clarify the meaning and scope of the durability

requirements and how these requirements can be included into the technical specifications of the products and systems. The technical report identifies the aspects of durability as a property of a product / installation to last for a definite time (long term) without showing breaks or weaknesses that could affect its use which may provide guidance for the preparation of technical specifications and product / system standards in relation to the intendeduseandtheassessmentmethodstobeadoptedfordurability.Thistechnicalreportdoesnotcoverinstallation.




Subsector : N14 Registration Date : 2017-09-28Organization : UNICountry : Italy


ICS : 23.040.01, 83.080.01National Ref : UNI1603537

Page 31

Title : Durability of the products and of the systems made of plastic materials - Guidelines for thedeterminationsoftheassessmentmethodsandtherelatedtests

Scope : The technical report has been drafted to clarify the meaning and scope of the durability requirements and how these requirements can be included into the technical specifications of the products and systems. The technical report identifies the aspects of durability as a property of a product / installation to last for a definite time (long term) without showing breaks or weaknesses that could affect its use which may provide guidance for the preparation of technical specifications and product / system standards in relation to the intendeduseandtheassessmentmethodstobeadoptedfordurability.Thistechnicalreportdoesnotcoverinstallation.



** End of Sector **






Page 33Subsector S09: WATER QUALITY AND WATER SUPPLY

Subsector : S09 Registration Date : 2017-09-06Organization : UNMZ Draft Issue Date : 2017-08-31Country : Czech Republic Latest Date for Comments : 2017-11-30


ICS :National Ref :Title : Water quality - Determination of radium 226

Relatedness :National : REV/AMD CSN 75 7822 (1998)

Subsector : S09 Registration Date : 2017-09-27Organization : UNMZCountry : Czech Republic


ICS :National Ref :Title : Water quality - Classification of surface water quality

Relatedness :National : REV/AMD CSN 75 7221 (1998)


Subsector S22: ENERGY SAVING

Subsector : S22 Registration Date : 2017-09-07Organization : NENCountry : Netherlands


ICS : 75.160.01National Ref : NTA 8003:2017 Concept nlTitle : Classification of biomass for energy recoveryScope : NTA 8003 describes a classification system to range solid and liquid biomass for energy

recovery.



** End of Sector **






Page 35Subsector T04: TYRES

Subsector : T04 Registration Date : 2017-09-11Organization : UNECountry : Spain Latest Date for Comments : 2017-10-21


ICS :National Ref : PNE 69050Title : Tyres, rims and valves. Tyre use cycle. Maintenance, repair and regrooving of tyres

manualScope : TO ESTABLISH BASIC STANDARDS FOR A CORRECT TYRE MAINTENANCE; AS WELL AS A

CORRECT REPAIR AND REGROOVING WHEN ALLOWED AND NECESSARY, FOR ENSURING THAT ALL THE SAFETY CONDITIONS ARE PRESERVED DURING ITS USEFUL LIFE, TAKING CARE OR ITS STRUCTURE TO ENLARGE ITS USEFUL LIFE.




ICS :National Ref : PNE 69051Title : Tyres, rims and valves. Tyre use cycle. Second-hand tyresScope : To define characteristics, verification and marking for used tyres, capable of being reused as

second-hand tyres



Subsector T18: ELEVATING PLATFORMS



ICS :National Ref : PNE 58921Title : Instructions for the fitting, handling, check and revisions of mobile elevating work

platformsScope : This technical specification provides requirements for the fitting, handling, check and

revisions of mobile elevating work platforms (this document supersedes UNE 58921:2002 IN). It covers all the type Platforms included and manufactured according to EN 280.

Relatedness :National : REV/AMD UNE 58921:2002 IN


Subsector T20: TRAM- AND RAILWAY ENGINEERING

Page 36

Subsector : T20 Registration Date : 2017-09-28Organization : UNICountry : Italy


ICS : 45.060National Ref : UNI1603453Title : Metropolitan railways and tramways - Horizontal and vertical track alignmentScope : This standard provide rules for the design of the horizontal and vertical alignment of the

lines, the track cant and the track gauge widening. This standard applies to the lines of transport systems “metro”, “light metro”, “rapid tramway” (or “light rail”) and “tramway”, as defined in UNI 8379.



** End of Sector **

2011-06


Sector A: Services


reference reference


















reference reference


B02 Structures 59; 98 166; 167; 250; 277; 346; 349; 284; 288; 297; 340


B04 Cement 74; 77 51


B06 Gypsum / 241

B07 Glass 160 129





B12 Masonry 179; 196 125; 246




B16 Taps / /





B21 Baths / /

















reference reference





C05 Lac / /


C08 Pesticides 81 /


C10 Starch 93 /

C11 Tobacco 126 401

C12 Glass plant / /




C18 Adhesives / 193








reference reference




F04 Sieves 24 /


294; 318; 244; 367; 141; CEN/WS 011



F08 Surfaces / 290

F09 Banking 68 /

F10 Statistics 69 /








F19 Optics 172; 187 123; 170









reference reference






H06 Horology 114 /

H07 Space heating 116 62; 110; 130; 179; 180








H15 Toys 181 52

H17 Oil stoves / 46




H23 Ladders / 93





H28 Hunting 191 /







H99 Undetermined / 299; 364; 369; 402



reference reference


I02 Fasteners 2 185





I07 Shafts 14 /



I10 Splines / /

I11 Machine tools 39 142; 143; 145; 255



I14 Gears 60 /




I18 Mining 82 196





I23 Pumps 115 197








I31 Valves 153; 185 69; 236; 105

I32 Flanges / 74
















reference reference


M02 Zinc / 209


M04 Copper 26 133

M05 Welding 44 121




M09 Iron ores 102 /





M14 Nickel 155 /











reference reference





N05 Textiles 38 189; 248

N06 Rubber 45 218; 366 CEN/WS 003


N08 Mica / /

N09 Plastics 61 249

N10 Cork 87 /



N13 Leather 120 289


N17 Fluorspar 175 /


N19 Tapes / 253




N23 Diamond / 410




reference reference



S03 Syringes 84 /





























reference reference




T04 Tyres 31 /

T05 Pallets 51 /



T08 Cranes 96 147






T14 Packaging 122 261; 120

T15 Cycles 149 333
























Sector A : SERVICES


Page 3Subsector A04: TRANSPORTATION SERVICES

Subsector : A04 Registration Date : 2017-10-18Organization : IPQ Draft Issue Date : 2017-10-16Country : Portugal Latest Date for Comments : 2017-11-16

Project ID : C1481701/0001 Draft for public enquiry

ICS : 03.120, 03.220National Ref : prNP 4558Title : Car parks. Interface with public passenger transport. Characteristics and service

provisionScope : The purpose of this standard is to specify the minimum qualitative and quantitative

characteristics and requirements as well as the quality requirements for the provision of a car park service with an interface to public passenger transport. It applies to all entities whose activity is the provision of service of car parks integrated with other modes of transport.



Subsector A06: BUILDING AND CONSTRUCTION SERVICES

Subsector : A06 Registration Date : 2017-10-27Organization : BSICountry : United Kingdom


ICS :National Ref : BS 67000Title : City resilience - Guide. Guide






ICS :National Ref : BS 8604-1Title : Socialalarmsystems-Installationofsocialalarmsystems.Part1:Grouped

living



Page 4


ICS :National Ref : BS 102000Title : Code of practice for the provision of investigative services




ICS : 03.080.30National Ref :Title : General rules for sale, repair and change places of road vehicle tiresScope : This standard includes, general rules for sale, repair and change places of road vehicle tires.



** End of Sector **









ICS : 91.140.99National Ref : UNI1601341Title : Heatingappliancesfiredbywoodorothersolidbiofuels

Installations requirementsScope : This standard specifies the installation requirements for heating appliances with a nominal

heat input <35 kW fired by wood or other solid biofuels.






ICS :National Ref : BS 8081:2015+A1:2017 CorrigendumTitle : Code of practice for grouted anchors. Corrigendum




ICS : 91.080.40National Ref : NEN 8760:2017 Concept nlTitle : Additional regulations to EN 13670 Execution of concrete structures Scope : NEN 8760 gives additional requirements to NEN-EN 13670 for execution of concrete

structures,




ICS :National Ref :

Page 7

Title : Utility tunnels and other associated paths of engineering networksScope : The aim of the amendment is unification of the standard for utility tunnels and other

associated paths of engineering networks according to the other standards.

Relatedness :National : REV/AMD CSN P 73 7505 (2017)



ICS :National Ref : PNE-EN 1998-4/1MTitle : Eurocode 8 - Design of structures for earthquake resistance - Part 4: Silos, tanks and

pipelines.1st Amendment: National annexScope : This modification includes the national annex of UNE-EN 1998-4, establishing the nationally

determined parameters, some non-contradictory complementary information and the status of informative annexes




Subsector : B04 Registration Date : 2017-10-18Organization : ISRM

Country :Former Yugoslav Republic of Macedonia


ICS : 75.140, 91.100.50National Ref : HМКС1018:2017Title : Bitumenandbituminousbinders–АniononicbituminousemulsionsforroadsScope : This standard determines the quality requirements for anionic bitumen emulsions (alkaline

bitumen emulsions ), which are used as a tack coat between the asphalt layers in road pavements (using mineral materials with carbonate composition, recpectively with sedimentary origin) .




ICS : 91.100.10National Ref : UNI1603597Title : Cements resistant to alkali-silica reactionScope : The standard is to define the content values of alkali equivalents (Na2Oeq = Na2O + 0.64 *

K2O) for common cement so that the cements can be used as inhibitors for the expansive

Page 8

reaction that some aggregates, containing particular forms of silica / silicates, may occur. The phenomenon is known as alkalisilica reaction (ASR).




ICS : 91.100.10National Ref : UNI1603598Title : Methods for the determination of the capacity to resist ASR for non CEM I cementScope : The standard specifies a test method to determine the contribution of effective alkali to all

concrete constituents, such as, for example, the common cements of EN 197-1 containing pozzolanic materials and slag, here called non-CEM I, whose use as ASR inhibitors is generally recognized.



Subsector B05: FIRE TESTS



ICS : 13.220.50, 91.060.20National Ref : NEN 6063:2017 Concept nlTitle : Test method for external fire exposure to roofsScope : The standard gives the experimental method for the determination of the fire behaviour of

roofs on exposure to fire brands and a limited radiant heat intensity.



Subsector B07: GLASS



ICS : 81.040.20National Ref : prNBN S 23-002-2:2017Title : Glazing - Part 2: Calculation of the glass thickness

Relatedness :National : REV/AMD NBN S 23-002-2:2016

Page 9



ICS : 81.040.20National Ref : prNBN S 23-002-3:2017Title : Glazing - Part 3: Calculation of the glass thickness in facades

Relatedness :National : REV/AMD NBN S 23-002-3:2016


Subsector B08: DOORS AND WINDOWS

Subsector : B08 Registration Date : 2017-10-17Organization : SIS Draft Issue Date : 2018-04-01Country : Sweden Latest Date for Comments : 2017-12-17


ICS : 91.060.50National Ref : 4362104Title : Emergency opening device on doors in locations for switchgear and controlgearScope : The standard only deals with emergency doors on the outgoing doors from the switch room.

The standard provides rules for the performance, testing and labeling of emergency launchers.




ICS :National Ref : PNE 85160Title : Security doors and hardware. Minimum requirements related to protection and resistance

class. Selection, application and installation criteria.Scope : This standard specifies the criteria for selection, application and installation of burglar

resistancesecuritydoorsfromsecuritylevel3,specifiedinUNE-EN1627:2011.It applies to the door, including frame, sash(es), hardware (turning elements, lock, cylinder andsecurityrosette)andinstallation.This standard provides a classification of security doors depending on additional parameters to burglary resistance: clean attack protection (without using physical force), access control, accessandattackdetection,properinstallationanddocumentarycontrol.The standard also defines test methods which consider the use of new tools for manual attack and documentary evidence to improve the protection of the lock device against skill

Page 10

attacks, such as bumping, key copying or fast pick locking. These additional parameters are brokendownintodifferentlevelsofprotection.The standard includes the physical adjustments to incorporate sensors that can be connected to intrusion alarm electronic systems and it gives maintenance recommendations forsecuritydoors.This standard does not apply to strongroom doors and strongrooms included in the scope of EN 1143-1.



Subsector B09: THERMAL MATTERS



ICS : 03.100.30, 27.220National Ref : UNI1603378Title : Exterior Insulation and Finishing System (EIFS) - Professionals performing installation of

Exterior Insulation and Finishing System (EIFS) - Knowledge, skill and competence requirements

Scope : The standard defines the knowledge, competence, formation and valuation requirements for qualification of operators for Exterior Insulation and Finishing System installers.




ICS :National Ref : BS 5250Title : Code of practice for control of moisture in buildings



Subsector B12: MASONRY



ICS :

Page 11

National Ref : 00518094Title : Earthen Boards - Terms and definitions, requirements, test methods




ICS :National Ref : 00518152Title : Earth blocks - Terms and definitions, requirements, test methods




ICS :National Ref : 00518153Title : Earth masonry mortar - Terms and definitions, requirements, test methods




ICS :National Ref : 00518154Title : Earth plasters - Terms and definitions, requirements, test methods



Subsector B13: SOLAR ENERGY



ICS : 27.160National Ref : ÖNORM H 7701 Beiblatt 1

Page 12

Title : Thermal Solar Systems - Supplement 1: General characteristics for the calculation of passive solar installations and for flat collectors in domestic hot water systems

Scope : This ÖNORM contains an approximation procedure for the calculation of the collector surface area of flat collectors in thermal solar systems for hot water production. The simplified assessment procedure of this ÖNORM can be applied to systems with the followingboundaryconditions:-Plantswithagrosscollectorareaupto20m²-Plantswhicharemainlyusedforwaterheating-Plantswithoutsignificantsouth-weakeningoftheorientationofthecollectorsAnnex 1 contains those general and geographical characteristics necessary for the calculation in accordance with ÖNORM H 7701.



Subsector B20: DRAINAGE EQUIPMENT



ICS :National Ref : PNE 127916Title : Concrete pipes and fittings, unreinforced, steel fibre and reinforced. National complement

to the UNE-EN 1916:2008 standard.Scope : This Project revises the previous version of the national Annex (which complements the

European Standard EN 1916:2008 which specifies performance requirements and describes test methods for precast concrete pipes and fittings, unreinforced, steel fibre and reinforced, for use in pipelines with flexible joints).



Subsector B23: DISTRICT HEATING





ICS :17.200.10, 27.060.30, 91.140.10

National Ref : UNI1603430Title : On site measurements - Heat generators - Part 4: District heating and cooling plantsScope : The standard describes procedures to be followed on site to measure the heat output and

the inlet/outlet temperatures of the heat exchangers connected to district heating and cooling plants.






ICS : 91.140.40National Ref : UNI1603707Title : Operativeinstructionforperiodicandrandommetrologicalinspections

Part2:GasvolumeconversiondevicesassociatedwithgasmetersScope : This standard provides requirements relating to metrological verification regarding the

correct operation of volume conversion devices associated with gas meters. These devices allow automatic conversion of measured gas quantity to thermodynamic reference conditions.

Relatedness :National : REV/AMD UNI 11600-2:2017



Subsector : B26 Registration Date : 2017-10-27Organization : BSI Draft Issue Date : 2017-09-11Country : United Kingdom Latest Date for Comments : 2017-10-11


ICS :National Ref : PD 6689Title : PD6689.Surfacetreatments.GuidanceontheuseofBSEN12271andBSEN

12273



Subsector B31: HEATING SYSTEMS IN BUILDINGS



ICS : 17.200.10, 91.140.10National Ref : UNI1601337Title : Onsitemeasurements-Heatgenerators-Part1:Heatpumps/chillers

Scope : The standard defines the control of energy efficiency changes over time affecting heat

pumps/chillers for heating and cooling systems


Page 14





ICS : 91.140.99National Ref : UNI1601341Title : Heatingappliancesfiredbywoodorothersolidbiofuels

Installations requirementsScope : This standard specifies the installation requirements for heating appliances with a nominal

heat input <35 kW fired by wood or other solid biofuels.




ICS :17.200.10, 27.060.30, 91.140.10

National Ref : UNI1602719Title : On site measurements - Heat generators - Part 1: Heat generators fed with liquid and/or

gaseousfuelsScope : Thisstandarddefinestheprocedurestoperformthefollowingonsitemeasurements:

-Measurementoftheheatoutputoftheheatgenerator;-Samplingandanalysisofthecombustionproducts;-Measurementofthetemperatureoftheproductsofcombustionandcombustionair;- Measurement of the concentrations of oxygen (O2) or carbon dioxide (CO2) and carbon monoxide(CO);-Measurementofthesmokeindex(onlyforgeneratorsfedwithliquidfuels);Thestandardalsoprovidestherulesforthecalculationofthecombustionefficiency.




ICS :17.200.10, 27.060.30, 91.140.10

National Ref : UNI1603305Title : On site measurements - Heat generators - Part 2: Heat generators fed with non

pulverized biofuelsScope : The standard describes procedures to be followed on site to measure draught, gas analysis

and combustion performance for non pulverized solid biofuel heat appliances


Page 15



ICS : 91.140.01, 91.140.60National Ref : UNI1603410Title : Water treatment in winter and summer air conditioning systems, for production of

domestic hot water and solar thermal systemsScope : The purpose of this standard is the definition and determination of the chemical and

chemical-physical characteristics of the water used in winter and summer air conditioning systems, for production of sanitary hot water with a maximum temperature of 180°C and in solar thermal systems for winter and summer air conditioning and for the production of sanitaryhotwater.




ICS :17.200.10, 27.060.30, 91.140.10

National Ref : UNI1603430Title : On site measurements - Heat generators - Part 4: District heating and cooling plantsScope : The standard describes procedures to be followed on site to measure the heat output and

the inlet/outlet temperatures of the heat exchangers connected to district heating and cooling plants.




ICS : 17.200.10, 91.140.01National Ref : UNI1603512Title : Energy performance of buildings - Part 2: Evaluation of primary energy need and of

system efficiencies for space heating, domestic hot water production, ventilation and lighting for non-residential buildings

Scope : The technical specification provides data and methods for evaluating: the energy need for hot water production, systems efficiencies and primary energy need for space heating and hot water production, primary energy need for ventilation, primary energy need for lighting of non-residential buildings. The technical specification applies to newly design systems, retrofitting or to existing systems - for heating only - mixed or combined heating and domestic hot water - for producing only hot water, for ventilation only systems, for combined ventilation and space heating systems, for lighting systems in non-residential buildings.

Relatedness :

Page 16

National : REV/AMD UNI/TS 11300-2:2014



Subsector : B33 Registration Date : 2017-10-18Organization : LVS Draft Issue Date : 2017-10-20Country : Latvia Latest Date for Comments : 2017-12-20


ICS : 91.080National Ref : prLVS 1046Title : Requirements for content and detailing of structural design documents and drawingsScope : The standard gives detailed instructions for content and detailing of structural design, it is

based on the requirements of the Latvian construction legislation and the good practice. Purpose of the standard – united and unified guidance of structural building design services. The standard shall be used in buildings and structures design, as far as it is not conflicting with the special requirements for the design of special structures.

Relatedness :National : REV/AMD LVS 1046:2015





ICS :National Ref : BS 1722-1Title : Fences. Part 1: Specification for chain link fences




ICS :National Ref : BS 1722-10Title : Fences.Part10:Specificationforanti-intruderfencesinchainlinkand

weldedmesh


Subsector : B99 Registration Date : 2017-10-18Organization : IPQ Draft Issue Date : 2017-10-16

Page 17

Country : Portugal Latest Date for Comments : 2017-11-16

Project ID : C1931702/0001 Draft for public enquiry

ICS : 13.100, 13.340National Ref : prNP 4557Title : Work at heigths. Collective protection equipment in infrastructures. BuildingsScope : This Standard specifies the minimum requirements that the different infrastructures referred

in this Standard shall present in order to ensure the inherent safety associated with the operation and maintenance work at heights, favoring the collective protection equipment in infrastructures. This way, the goals of this document are: • To establish the process, methodologies and resources needed for the selection and installation of collective protection equipment suitable for the development of maintenance operations to carry out work at heights, considering the risk of falling from a height, namely on roofs, facades and interior courtyards; • To frame the typology of specific protection equipment against the risk of falling from a height, that the roofs, facades and interior courtyards should be equipped with, considering buildings to build, and built up existing ones


Subsector : B99 Registration Date : 2017-10-27Organization : TSECountry : Turkey


ICS : 91.100.99National Ref :Title : Bars for concrete reinforcement – Made of glass fibre reinforced plastics (GFRP) -

RequirementsScope : This standard specifies the requirements of round, deformed reinforcing bars which have

been produced by glass fibre reinforced plastics (GFRP) to be used for reinforcement in concrete where empowered by TS 500 “Building Code for Reinforced Concrete Structures” and “Specification for Buildings to be Built in Seismic Zones”.

Relatedness :National : NewInternational : Identical to ASTM D7957:2017



ICS : 91.040.01National Ref :Title : Building LicenceScope : This standard covers Building Licence



** End of Sector **







Subsector : C01 Registration Date : 2017-10-19Organization : LVS Draft Issue Date : 2017-10-20Country : Latvia Latest Date for Comments : 2017-12-20


ICS : 67.120.30National Ref : prLVS 27Title : Canned fish. Riga Sprats in Oil. Sprats in OilScope : Standard defines the quality and harmlessness requirements of canned, sterilized fish, the

raw materials, components and forms of packaging, transport and storage regimes. Standard of canned, sterilized fish products concerned the following parameter type: "Riga Sprats in Oil" and "Sprats in Oil".




ICS : 67.060National Ref :Title : Flour and baked goods-Cystin-Cystein and Glutamic acid determination with LCMSMS Scope : This standard specifies a method for the determination of cystin, cystein and glutamic acid in

flour and baked goods




ICS : 67.060National Ref :Title : Frozen-PizzaScope : This standard covers frozen pizza




ICS : 67.180.10National Ref :Title : Dough desserts – Ready to syrup-add

Page 20

Scope : This standard specifies dough desserts which is ready to syrup-add




ICS : 67.060National Ref :Title : Baby biscuits Scope : This standard kovers baby biscuits






ICS :National Ref : 00200971Title : Driers for paints and varnishes Methods for determination of metal contents of mixed

driers



Subsector C20: EXPLOSIVES AND FIREWORKS



ICS : 71.100.30, 95.020National Ref :Title : Mine action - Accreditation of mine action organisationsScope : This standard provides specifications and guidelines for the implementation of a system for

accreditation of mine action organisations.


Subsector : C20 Registration Date : 2017-10-17

Page 21

Organization : TSECountry : Turkey


ICS : 71.100.30, 95.020National Ref :Title : Mine action - Land ReleaseScope : This standard provides guidance and sets out minimum requirements to enable the

development of a national land release policy and outlines broad responsibilities and obligations of the National Mine Action Authorities, demining organisations and agencies involved.




ICS : 71.100.30, 95.020National Ref :Title : Humanitarianmineaction-Follow-onprocessesaftertheuseof

demining machinesScope : This standard provides the follow-on processes after the use of demining machines. It makes

a general statement about follow-on processes after the use of a demining machine in a ground preparation role when the operation is carried out within an area of suspected hazard.




ICS : 71.100.30, 95.020National Ref :Title : Mine action - Protection of the environment of mine worksiteScope : This standard provides guidelines as to the minimum environmental protection measures

that should be complied with to ensure that environments affected by survey and clearance operations are not degraded by the work and are fit for their intended use once demining is completed.




Page 22

ICS : 71.100.30, 95.020National Ref :Title : Mineaction-Deminingworksitesafety

demining machinesScope : This standard provides specifications and guidance on the development and implementation

of policy and documented procedures and practices that aim to establish and maintain a safe demining worksite.



** End of Sector **






Page 24Subsector F07: DOCUMENTATION AND INFORMATION

Subsector : F07 Registration Date : 2017-10-20Organization : NSAICountry : Ireland

Project ID : 0NSAI895/0001 Project Established

ICS : 93.080.20, 93.080.20National Ref : S.R. 28Title : Recommendation for the use and implementation of the I.S. EN 13108 series bituminous

mixtures – material specificationsScope : This S.R. gives guidance on the use of I.S. EN 13108 parts 1, 2, 4, 5, 7, 8, 20 and 21. t does not

give guidance on I.S. EN 13108 - 3, Soft Asphalt, as this is not used in Ireland. I.S. EN 13108 - 6, Mastic Asphalt is outside the scope of this S.R. The application of this S.R. is for roads and other paved areas excluding airfields. Detailed provisions for airfields are specified elsewhere.

Relatedness :National : REV/AMD S.R. 28:2009

Subsector : F07 Registration Date : 2017-10-20Organization : NSAICountry : Ireland

Project ID : NSAI1025/0001 Project Established

ICS : 01.110, 01.140, 35.240.20National Ref : I.S. 374Title : Universal Design for customer communication for Utility servicesScope : gives requirements and guidance on Universal Design for Energy Suppliers to household

customers in the provision of energy products, supporting services and associated communications;is intended to assist suppliers to make products and services accessible and usable by as manypeopleaspossiblewithouttheneedforadditionaladaptationorspecializeddesign;does not address the design, or the operation, of any meters, appliances, or pipework to which the energy is connected.

Relatedness :National : REV/AMD SWiFT 9:2012


Subsector F16: GRAPHICAL SYMBOLS



ICS : 01.080.10National Ref : ÖNORM ISO 7001Title : Graphical symbols - Public information symbolsScope : This ÖNORM specifies graphical symbols for the purposes of public information and is

generally applicable to public information symbols in all locations and all sectors where the public has access. However, it is not applicable to safety signs or to those sectors subject to a regulation which may differ with regard to certain points (for example, traffic signs on the

Page 25

public highway). This standard specifies the symbol originals that may be scaled for reproduction and application purposes. The symbols may be used in conjunction with text to improve comprehension.




Subsector : F20 Registration Date : 2017-10-27Organization : BSICountry : United Kingdom


ICS :National Ref : BS 42021Title : Biodiversityandthebuiltenvironment:SpecificationfortheDesign

andInstallation of Bird Boxes


Subsector : F20 Registration Date : 2017-10-27Organization : BSICountry : United Kingdom


ICS :National Ref : BS 8599-1Title : Workplacefirstaidkits.Specificationforthecontentsofworkplacefirstaid

kits




ICS :National Ref : PNE 192011-7Title : Procedure for the regulatory inspection. Pressure equipment. Part 7: Specific

requirements for transportable pressure vessels. Gas recharge centersScope : This standard describes the systematic action for the inspections planned under current

regulation in order to specifically verify the safety of transportable pressure receptacles


Subsector : F20 Registration Date : 2017-10-06Organization : UNE

Page 26

Country : Spain Latest Date for Comments : 2017-11-15


ICS :National Ref : PNE 179002Title : Health services. Quality management system for health care transport organization.Scope : This standard specifies the quality management system in health care transport organization.



** End of Sector **






Page 28Subsector H07: SPACE HEATING



ICS :National Ref : 04111934Title : Terminology



** End of Sector **






Page 30Subsector I17: MACHINERY IN GENERAL (INCLUDING SAFETY)

Subsector : I17 Registration Date : 2017-10-30Organization : UNICountry : Italy


ICS : 13.020.01, 13.100, 13.200National Ref : UNI1603620Title : Establishments with major-accident hazard - Safety management systems - Essential

requirementsScope : The standard provides the basic requirements for the preparation, implementation,

maintenance and improvement of a safety management system, aimed at the prevention of major accidents related to the use of dangerous substances, as defined by the current laws and regulations.



Subsector I36: THERMOPROCESSING TECHNOLOGY



ICS : 13.020.01, 13.100, 13.200National Ref : UNI1603703Title : Establishments with major-accident hazard - Safety management systems - Guidelines

on implementation of UNI 10617Scope : The standard provides guidance on the establishment, implementation, maintenance and

improvement of a safety management system in accordance with the requirements of UNI 10617, and, for each requirement of this standard, it describes the procedures and technical tools that may be helpful for the achievement of the specific objectives. It applies to the operation of plants in establishments with a major-accident hazard, or to the operation of technical units in establishments where dangerous substances are produced, used, handled and stored.



Subsector I40: INDUSTRIAL PIPING NETWORKS

Subsector : I40 Registration Date : 2017-10-02Organization : LVS Draft Issue Date : 2007-10-03Country : Latvia Latest Date for Comments : 2007-12-04


ICS : 23.040.01National Ref : prLVS 418Title : Gas supply systems. External gas pipelines. ConstructionScope : Standard sets requirements for general arrangements, earth work and metal pipeline

construction in natural gas transmission, distribution and service external system

Page 31

construction.

Relatedness :National : REV/AMD LVS 418


** End of Sector **






Page 33Subsector M01: STEEL

Subsector : M01 Registration Date : 2017-10-18Organization : DINCountry : Germany


ICS :National Ref : 02001101Title : Industrial steel storage drawer cabinets - Design, functional and safety requirements,

testing and evaluation



Subsector M08: LIGHT ALLOYS

Subsector : M08 Registration Date : 2017-10-06Organization : UNECountry : Spain Latest Date for Comments : 2017-11-15


ICS :National Ref : PNE 38213Title : Aluminium and aluminium alloys for casting. Group Al-Cu. Alloy L-2130 Al-7CuSiScope : This standard, included in the general considerations established in UNE 38200, is intended

to define the chemical composition and mechanical characteristics required of alloy L-2130, Al-7CuSiofaluminiumforcasting.In the Annex A (Informative) there are some other data of interest for the user.



** End of Sector **






Page 35Subsector N03: PETROLEUM PRODUCTS



ICS : 93.080.20National Ref : ÖNORM B 3613Title : Polymer modified bitumen for road construction - Requirements - Rules for the

implementation of ÖNORM EN 14023Scope : This ÖNORM provides specifications for polymer modified bitumen which is suitable for use

intheconstructionofroads,airfieldsandotherpavedareas.ThisÖNORMcoversthefollowingcharacteristics:-consistencyatintermediateservicetemperature;-consistencyatelevatedservicetemperature;-cohesion;-durabilityofconsistency;-brittlenessatlowservicetemperature;-strainrecovery.The cohesion property has been included as a mean of discriminating between polymer modified bitumen and other bituminous binders. The other essential requirements, "adhesion" and "setting ability" are indicated by tests carried out on the finished asphalt mixtures.Austria evaluates currently on a voluntary basis new test methods to collect experiences for furtherdevelopments.Forthispurposethefollowingtestmethodswillbeevaluated:-BendingBeamRheometer,basedonthetestmethodaccordingtoÖNORMEN14771,and-DynamicShearRheometer,basedonthetestmethodaccordingtoÖNORMEN14770.These data can be declared at the declaration of conformity and are to be listed according Annex A (table A.1 and table A.2).




ICS : 75.120National Ref : 155434Title : Hydraulic fluids — Technical requirements, environmental properties and test methods Scope : Amendment to SS 155434 to add reference to SS-EN 16807 for "biobased hydraulic fluids"




ICS : 75.120National Ref : 155470

Page 36

Title : Lubricants, industrial oil and related products (Class L) Specifications for family X (Greases)

Scope : Amendment to SS 155470 to add reference to SS-EN 16807 for "biobased greases"


Subsector : N03 Registration Date : 2017-10-20Organization : PKNCountry : Poland


ICS : 75.080National Ref : prPN-C-96060Title : Petroleum products – Determination of the pH of water extractScope : This standard specifies a method for the determination of the pH of the water extract of

petroleum products, distillation residues and additives. The standard specifies two procedures A and B to determine the pH of the water extract. Procedure A applies to the pH determination using a pH-meter, while the procedure B is visual detemination method using colour indicators



Subsector N12: TIMBER PRODUCTS



ICS :National Ref : 04200966Title : Wood shingles



Subsector N21: GASEOUS FUELS AND COMBUSTIBLE GAS

Subsector : N21 Registration Date : 2017-10-02Organization : LVS Draft Issue Date : 2007-10-03Country : Latvia Latest Date for Comments : 2007-12-04


ICS : 75.060National Ref : prLVS 460Title : Utilization of gases manufactured from renewable sources in natural gas distribution

systemScope : Standard applies to gases obtained by fermentation of biomass and is intended for entering

in the natural gas transmission systems, and use of biogas/natural gas mixtures

Page 37

Relatedness :National : REV/AMD LVS 460


** End of Sector **






Page 39Subsector S04: PROTECTIVE CLOTHING AND EQUIPMENT

Subsector : S04 Registration Date : 2017-10-27Organization : BSICountry : United Kingdom


ICS :National Ref : BS 8887-3Title : Designformanufacture,assembly,disassemblyandend-of-lifeprocessing.Part

3: Guide to choosing an appropriate end-of-life strategy




Subsector : S09 Registration Date : 2017-10-27Organization : BSICountry : United Kingdom


ICS :National Ref : BS 8580-1Title : Waterquality.RiskassessmentsforLegionellacontrolCodeof

practice



Subsector S99: UNDETERMINED



ICS : 03.120, 13.160National Ref : NTA 8009:2017 Concept nlTitle : Safety management system for hospitals and institutions which deliver hospital careScope : NTA 8009 gives specifications to set up a system for safety in hospitals for patients and

employees. Gives definitions for safety, responsibilities and the requirements for employees.



** End of Sector **






Page 41Subsector T01: SHIPBUILDING AND MARITIME STRUCTURES



ICS :National Ref : PNE 27751Title : Civil shipbuilding and ship repairing. Standardised components. Penetration pipe pieces:

Single flange penetration pieceScope : This standard specifies the design, dimensions and technical requirements for single flange

penetration pieces for PN10 and PN16, suitable for installation in pipe systems on sea-going vesselsfulfillingtheirnormalservicerequirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies.





Flanged penetration piece for PN6Scope : This standard specifies the design, dimensions and technical requirements for flanged

penetration pieces for PN6, fabricated from UNE-EN 10220 tube, suitable for installation in pipesystemsonsea-goingvesselsfulfillingtheirnormalservicerequirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies.





Flanged penetration piece for PN10 and PN16Scope : This standard specifies the design, dimensions and technical requirements for flanged

penetration pieces for PN10 and PN16, fabricated from UNE-EN 10220 tube, suitable for installationinpipesystemsonsea-goingvesselsfulfillingtheirnormalservicerequirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies.

Page 42





Flanged angle penetration pieceScope : This standard specifies the design, dimensions and technical requirements for flanged angle

penetration pieces fabricated from UNE-EN 10220 tube, suitable for installation in pipe systemsonsea-goingvesselsfulfillingtheirnormalservicerequirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies





Single flange penetration piece with sleeveScope : This standard specifies the design, dimensions and technical requirements for single flange

penetration pieces with sleeve, for PN10 and PN16 fabricated from UNE-EN tube, suitable for installation in pipe systems on sea-going vessels fulfilling their normal service requirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies





Flanged penetration piece for PN10 and PN16, with ASTM tubeScope : This standard specifies the design, dimensions and technical requirements for flanged

Page 43

penetration pieces for PN10 and PN16, fabricated from ASTM tube, suitable for installation inpipesystemsonsea-goingvesselsfulfillingtheirnormalservicerequirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies




ICS :National Ref : PNE 27763Title : Civil shipbuilding and ship repairing . Standardised components. Penetration pipe pieces:

Single flange penetration piece, with ASTM tubeScope : This standard specifies the design, dimensions and technical requirements for single flanged

penetration pieces for PN10 and PN16, fabricated from ASTM tube, suitable for installation inpipesystemsonsea-goingvesselsfulfillingtheirnormalservicerequirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies





flanged angle penetration piece with ASTM tubeScope : This standard specifies the design, dimensions and technical requirements for flanged angle

penetration pieces for PN10 and PN16, fabricated from ASTM tube, suitable for installation inpipesystemsonsea-goingvesselsfulfillingtheirnormalservicerequirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies.




ICS :

Page 44

National Ref : PNE 27765Title : Civil shipbuilding and ship repairing. Standardised components. Penetration pipe pieces:

Single flange penetration piece with sleeve and ASTM tubeScope : This standard specifies the design, dimensions and technical requirements for single flange

penetration pieces with sleeve for PN10 and PN16, fabricated from ASTM tube, suitable for installationinpipesystemsonsea-goingvesselsfulfillingtheirnormalservicerequirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies.





Flanged penetration piece with sleeve for PN10 and PN16Scope : This standard specifies the design, dimensions and technical requirements for flanged

penetration pieces with sleeve for PN10 and PN16, fabricated from UNE-EN 10220 tube, suitable for installation in pipe systems on sea-going vessels fulfilling their normal service requirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies.





Flanged penetration piece with sleeve for PN10 and PN16, with ASTM tubeScope : This standard specifies the design, dimensions and technical requirements for flanged

penetration pieces with sleeve for PN10 and PN16, fabricated from ANSI-ASTM tube, suitable for installation in pipe systems on sea-going vessels fulfilling their normal service requirements.Specific application in every project shall fulfil the requirements of the relevant Regulatory Bodies.



Page 45Subsector T03: ROAD VEHICLES

Subsector : T03 Registration Date : 2017-10-02Organization : NBNCountry : Belgium


ICS : 43.120National Ref : prNBN R 03-001Title : Electrically propelled road vehicles – Controlling risks during interventions



Subsector T16: LIFTS & ESCALATORS



ICS :National Ref : BS 8486-8Title : Examinationandtestofnewliftsbeforeputtingintoservice-Specification

formeansofdeterminingcompliancewithBSEN81.Part8:Firefightersliftsconformingto BS EN 81-72




ICS :National Ref : BS 8486-9Title : Examinationandtestofnewliftsbeforeputtingintoservice-Specification

formeansofdeterminingcompliancewithBSEN81.Part9:Behaviourofliftsintheevent of fire conforming to BS EN 81-73



** End of Sector **

2011-06


Sector A: Services


reference reference


















reference reference


B02 Structures 59; 98 166; 167; 250; 277; 346; 349; 284; 288; 297; 340


B04 Cement 74; 77 51


B06 Gypsum / 241

B07 Glass 160 129





B12 Masonry 179; 196 125; 246




B16 Taps / /





B21 Baths / /

















reference reference





C05 Lac / /


C08 Pesticides 81 /


C10 Starch 93 /

C11 Tobacco 126 401

C12 Glass plant / /




C18 Adhesives / 193








reference reference




F04 Sieves 24 /


294; 318; 244; 367; 141; CEN/WS 011



F08 Surfaces / 290

F09 Banking 68 /

F10 Statistics 69 /








F19 Optics 172; 187 123; 170









reference reference






H06 Horology 114 /

H07 Space heating 116 62; 110; 130; 179; 180








H15 Toys 181 52

H17 Oil stoves / 46




H23 Ladders / 93





H28 Hunting 191 /







H99 Undetermined / 299; 364; 369; 402



reference reference


I02 Fasteners 2 185





I07 Shafts 14 /



I10 Splines / /

I11 Machine tools 39 142; 143; 145; 255



I14 Gears 60 /




I18 Mining 82 196





I23 Pumps 115 197








I31 Valves 153; 185 69; 236; 105

I32 Flanges / 74
















reference reference


M02 Zinc / 209


M04 Copper 26 133

M05 Welding 44 121




M09 Iron ores 102 /





M14 Nickel 155 /











reference reference





N05 Textiles 38 189; 248

N06 Rubber 45 218; 366 CEN/WS 003


N08 Mica / /

N09 Plastics 61 249

N10 Cork 87 /



N13 Leather 120 289


N17 Fluorspar 175 /


N19 Tapes / 253




N23 Diamond / 410




reference reference



S03 Syringes 84 /





























reference reference




T04 Tyres 31 /

T05 Pallets 51 /



T08 Cranes 96 147






T14 Packaging 122 261; 120

T15 Cycles 149 333
























Sector A : SERVICES


Page 3Subsector A01: TOURIST SERVICES

Subsector : A01 Registration Date : 2017-11-21Organization : ASICountry : Austria


ICS : 03.080.30, 03.200National Ref : ÖNORM D 1150Title : Services of the leisure industry - Requirements for the training of dance teachers and

dance masters as well as for the management of ballroom dance schoolsScope : This ÖNORM sets minimum requirements for the training and exam of dance teachers and

dance masters as well as for the management of a dance school (facilities and curriculum).



Subsector A05: MAINTENANCE SERVICES

Subsector : A05 Registration Date : 2017-11-09Organization : NENCountry : Netherlands


ICS : 97.020National Ref : NEN 2075:2017 nlTitle : Measuring system and process control system for cleaning performance Scope : This standard describes the measurement of quality for cleaning performance according to

objective criteria. With this sytem the performed quality can be compared with the prescribed quality.






ICS : 03.080.30, 11.040National Ref :Title : Competent services - Medical devices - Rules Scope :

This standard includes rules for management technical equipment structrural characteristics and personnel characteristics of the compenent services of medical equipments


Subsector : A11 Registration Date : 2017-11-17

Page 4



ICS : 03.080.30, 11.040.30National Ref :Title : Competent services – Surgical instruments – RulesScope : This standard includes rules for operating, structural feature, technical equipment, personnel

specifications and certification of competent services of surgical instruments used in health sector




ICS : 03.080.30, 11.040National Ref :Title : Private services - Medical devices - Rules Scope : This standard includes rules for management, structural features, technical equipment,

personnel specifications and certification of special services for medical devices



Subsector A99: UNDETERMINED

Subsector : A99 Registration Date : 2017-11-28Organization : UNICountry : Italy


ICS : 03.100.30National Ref : UNI1603735Title : Non-regulated professions - Professional profiles Human resources - Knowledge, skill

and competence requirementsScope : This standard specifies the requirements for the professional profiles Human resources, in

terms of knowledge, skills and competence, in accordance with the European Qualifications Framework, EQF.



** End of Sector **






Page 6Subsector B02: STRUCTURES



ICS :91.010.30, 91.080.40, 93.040

National Ref : ÖNORM B 1992-2Title : Eurocode 2 - Design of concrete structures - Part 2: Concrete bridges - Design and

detailling rules - National specifications concerning ÖNORM EN 1992-2, national comments and national supplements

Scope : This Austrian Standard specifies national parameters to ÖNORM EN 1992-2 and shall be applied jointly with ÖNORM EN 1992-2 in Austria. This standard describes the principles and requirements for safety, serviceability and durability of concrete structures, together with specific provisions for bridges.




ICS :91.060.40, 91.140.01, 97.100.30, 97.100.40

National Ref : UNI1603704Title : In-service installations for civil use powered by liquid and solid fuel - Guidelines for

verifying suitability for safe operationScope : The standard establishes the criteria for verifying that the safety requirements of in-service

installations powered by solid and/or liquid fuels are fulfilled, regardless of the time of their installation, in order to determine whether the verified plant can continue to be used in its currentstate,withoutcompromisingsafety.The standard deals exclusively with the aspects of verification of installations and therefore it cannotbeusedasadesignstandard,norasaninstallationstandardorforretrofitting.The standard applies to domestic heating and/or cooking systems powered by liquid or solid fuel, with or without the production of domestic hot water, including the works for the evacuation of combustion products.




ICS :National Ref :Title :

Bitumen and bituminous binders – Modified bitumens – Part 2: Crumb rubber modified bitumens

Scope : This standard contains the requirements of the Czech Republic for modified asphalt binders

Page 7

usedinroadconstruction.Thisstandardconsistsofthreeparts:Part1:PolymersmodifiedbitumensPart2:CrumbrubbermodifiedbitumensPart3:SpecialmodifiedbitumenČSN657222-2specifiestypesofbitumensmodifiedwithcrumbrubber.Aninternationalstandard has not yet been developed for this part 2, only the draft CEN / TC 336 / N 689 that has been taken into account.



Subsector B03: CONCRETE



ICS : 91.080.30National Ref : SIA 179Title : Fixings in concrete and masonry

Relatedness :National : REV/AMD SIA 179:1998



ICS : 91.080.40National Ref : SIA 262/1Title : Concrete Structures – Supplementary specifications

Relatedness :National : REV/AMD SIA 262/1:2013





ICS : 91.100.10National Ref :Title : Principles of Bulk Cement TransportationScope : This standard specifies the principles of transferring cement from the production line to the

transporting vehicle, transportation and preservation of the quality of bulk cement during these stages.

Page 8



Subsector B13: SOLAR ENERGY



ICS : 91.140.10National Ref : ÖNORM M 7510-8Title : Checking of heating systems -- Part 8: Basic check of thermal solar systemsScope : The actual ÖNORM is to be used for basic checks of heating and warmwater Systems

combined with a thermal solar Systems and is only valid for the parts of the thermal solar system. The actual check described in this ÖNORM helps evaluating the correct functioning.






ICS : 93.080.40National Ref : ÖNORM O 1051Title : Road lighting - Lighting of conflict areasScope : ÖNORM O 1051 is applicable to the construction of lighting system for safety crosswalk and

cyclists, roundabouts, divisional island and parking areas. Furthermore, Annex provides information on crossroads and lay-bys.






ICS :National Ref : 03200806Title : Gasfilters having a maximum working pressure of less or equal to 5 bar - Requirements

and testing

Relatedness :

Page 9

National : New



ICS :National Ref : 03200808Title : Gaskets for gas supply - Part 6: Gasket materials based on fibres, graphite or

polytetrafluoroethylene (PTFE) for gas valves, gas appliances and gas mains


Subsector : B25 Registration Date : 2017-11-10Organization : NSAICountry : Ireland


ICS : 91.140.40National Ref : I.S. 820:201xTitle : Non-domestic gas installations (Edition 3)Scope : This Irish Standard specifies the requirements for natural gas and LPG installations in

commercial and public access buildings at maximum operating pressures not exceeding 5 bar and industrial gas installations at maximum operating pressures not exceeding 0,5 bar, from the point of delivery up to and including the appliance(s) in non-domestic premises.

Relatedness :National : REV/AMD I.S. 820:2010

Subsector : B25 Registration Date : 2017-11-06Organization : NSAICountry : Ireland


ICS : 23.040.99National Ref : I.S. 328-2:201x Title : Gas transmission - Part 1, InstallationsScope : SeparationofcurrentparttwoofI.S.328intoaseparatestandard.

This Standard applies to the design, construction, inspection, testing, operation and maintenance of installations on pipelines used for the transmission of first and second family gases, i.e., manufactured towns gas, natural gas and substitute natural gas at maximum operatingpressureover16barandtemperaturesbetween-25oCand+120oCPipeline installations include but are not restricted to pressure-reduction stations, meter stations, pig-trap stations and block valves. Compressor stations and compressed gas filling stationsareexcluded.If the inlet pipework of the station is a service line and the maximum upstream operating pressure does not exceed 16 bar and the design flow rate is equal to or less than 200 m3/h undernormalconditions,EN12279applies.This Standard relates to conditions and practices currently in use in the transmission of gas. In addition materials and techniques of construction and operation are constantly being

Page 10

improved. It is intended to keep these factors under continuous review. As a result amendments and supplements may be issued by the National Standards Authority of Ireland (NSAI)fromtimetotime.All activities covered by this code in relation to gas transmission pipelines and installations should comply with the requirements of all relevant safety, planning and environmental legislation.




Subsector : B26 Registration Date : 2017-11-13Organization : ASROCountry : Romania

Project ID : 0NP187.2/0001 Project Established

ICS :National Ref :Title : Storable bituminous mixtures. Material specifications



Subsector B27: WATERPROOFING MATERIALS

Subsector : B27 Registration Date : 2017-11-08Organization : SIST Draft Issue Date : 2018-01-01Country : Slovenia Latest Date for Comments : 2018-02-08


ICS : 91.100, 91.100National Ref : oSIST 1031:2017Title : Flexible sheets for waterproofing - Bitumen sheets for waterproofing – RequirementsScope : SIST 1031 defines national requirements which supplement European standards and which

are not in conflict with them. The standard contains clearly-defined criteria for the essential characteristics of materials with regard to climate conditions in our country.




ICS : 91.060.20National Ref : UNI1603784Title : Discontinuous roofing – Design criteria – Waterproofing elementScope : The standard takes in consideration the behaviour requirements of the waterproofing

element in a discontinuous roofing according to the effects and actions of the internal or

Page 11

external agents. The standard provides a guidance for design of the element.




ICS : 91.060.20National Ref : UNI1603785Title : Building – Roofing – Terminology and classification of functional schemes, conform

solutions and technological solutions of discontinuous roofingScope : The standard show, defines and classifies the discontinuous roofing functional schemes,

reports the matrix of complying solutions and identifies the main conditions of characteristics design of the roofing complying solutions.




ICS : 91.060.20National Ref : UNI1603786Title : Builiding – Roofings – Analysis of functional components of discontinuous roofing and

design specifications for definition of technological solutionsScope : This standard provides instructions for design and choice of elements and layers of

discontinuous roof cooverings.




ICS : 91.060.20National Ref : UNI1603836Title : Building – Roofing – Terminology and classification of functional schemes, conform

solutions and technological solutions of continuous roofingScope : The standard show, defines and classifies the continuous roofing functional schemes, reports

the matrix of complying solutions and identifies the main conditions of characteristics design of the roofing complying solutions.



Page 12Subsector B32: PRECAST CONCRETE PRODUCTS



ICS : 91.100.30National Ref : prNBN B 21-606:2017Title : Precast concrete products – Floor plates – National application document to NBN EN

13747+A2:2010 and to NBN EN 15050+A1:2012

Relatedness :National : REV/AMD NBN B 21-606:2012European : Not Equivalent to EN 13747:2005+A2:2010



ICS : 91.100.30National Ref : prNBN B 21-606:2017Title : Precast concrete products – Floor plates – National application document to NBN EN

13747+A2:2010 and to NBN EN 15050+A1:2012




ICS : 91.100.30National Ref : prNBN B 21-612:2010/prA1:2017Title : Precast concrete products – Wall elements – National application document to NBN EN

14992+A1:2012




Subsector : B33 Registration Date : 2017-11-28Organization : LVSCountry : Latvia


ICS : 91.080National Ref : prLVS 1053Title : Independent verification of construction design. Structural design checking.Scope : The standard regulates procedures for carrying out expert examination of building’s

structural components. The document describes the compulsory checking procedures and

Page 13

the scope of office calculations stemming from the respective class of the building in question. The aim of the standard is to promote the standardization of the expertise process of the building structural units, making this process transparent and understandable to all the participants in the construction process.






ICS : 91.100.50National Ref : ÖNORM B 3662Title : Flexible sheets for waterproofing - Underlays for walls - National implementation of

ÖNORM EN 13859-2Scope : This standard is used for the implementation of ÖNORM EN 13859-2; It determines in clause

5 the minimum technical requirements for flexible sheets for waterproofing as underlays for discontinuous underlays for walls in terms of basic usability in Austria. The specific requirements for bitumen and plastic sheets that come in Austria for the application are in clause 6 and clause 7.




ICS : 91.100.50National Ref : ÖNORM B 3667Title : Flexible sheets for waterproofing - Synthetic vapour control layers - National

implementation of ÖNORM EN 13894Scope : This ÖNORM serves for implementation of the ÖNROM EN 13984. It determines in clause 5

the technical minimum-requirements for Synthetic vapour control layers in regarding to the in principal usability in Austria. The specific requirements on Synthetic sheets, which are used in Austria, are in clause 6.




ICS : 91.100.50National Ref : ÖNORM B 3668

Page 14

Title : Flexible sheets for waterproofing - Synthetic damp proof courses - National implementation of ÖNORM EN 14909

Scope : This ÖNORM serves for implementation of the ÖNROM EN 14909. It determines in clause 5 the technical minimum-requirements for Synthetic damp proof courses in regarding to the in principal usability in Austria. The specific requirements on Synthetic sheets, which are used in Austria, are in clause 6.




ICS : 91.100.23National Ref : ÖNORM B 3407Title : Planing and execution of laying of tiles, flags and mosaicsScope : This Austrian Standard includes rules for design and execution of laying of tiles, flags and

mosaicsintheinteriorandexterioralsoonheatingfloorscreeds.ThewaterproofingforbuildingsisregulatedinÖNORMB3691andÖNORMB3692.ThecleaningservicesareregulatedinÖNORMD2210.The requirement for slipping is defined in ÖNORM Z 1261.



** End of Sector **









ICS : 07.100.30National Ref : DIN 10164-1Title : Microbiological examination of meat and meat products - Determination of

Enterobacteriaceae - Part 1: Spatula method (reference method)




ICS : 07.100.30National Ref : DIN 10164-2Title : Microbiological examination of meat and meat products - Determination of

Enterobacteriaceae - Part 2: Drop plating method


Subsector : C01 Registration Date : 2017-11-20Organization : LSTCountry : Lithuania


ICS : 67.120.10National Ref :Title : Meat productsScope : This standard gives general quality requirements for human consumption meat products

supplied to the market.


Subsector : C01 Registration Date : 2017-11-15Organization : SNCountry : Norway


ICS : 67.120.30National Ref : NS 9444Title : Fish and fish products - Norwegian filet of white fish, frozen at sea - Product

requirementsScope : This standard specifies requirements and documentation of filet frozen at sea of white fish

with and without skin, with and without bones and with different cutting pattern

Page 17




ICS : 67.060National Ref :Title : Turkish BaklavaScope : This standard specifies Turkish Baklava






ICS : 87.060.10National Ref : DIN 55912-2Title : Pigments - Titanium dioxide pigments - Part 2: Analytical methods



Subsector C99: UNDETERMINED



ICS : 71.120.10National Ref : DIN 28125-1Title : Round hinged closures - Part 1: Nominal diameter DN 150 to DN 800



** End of Sector **






Page 19Subsector F99: UNDETERMINED

Subsector : F99 Registration Date : 2017-11-09Organization : NENCountry : Netherlands


ICS : 29.240.01, 91.140.50National Ref : NEN 9191:2017 Concept nlTitle : Energy efficiency of low voltage installations Scope : NEN 9191 gives additional requirements, measures and recommendations for the design, the

construction and verfification of electrical low-voltage installations among which the local production and storage of energy for more efficiënt use of electricity.



** End of Sector **






Page 21Subsector H09: FURNITURE

Subsector : H09 Registration Date : 2017-11-24Organization : TSECountry : Turkey


ICS : 97.130.10, 97.140National Ref :Title : Steel single tier bolted shelvingScope : This standard covers steel cabinets up to 1000 mm x 400 mm table dimension.



Subsector H19: NON-ELECTRIC COOKERS AND BARBECUES



ICS : 97.100.30National Ref : ÖNORM B 8311Title : Installation and construction of domestic heat generating systemsScope : This ÖNORM contains requirements for the installation and assembly of small furnaces

(heating appliances) for solid and liquid fuels up to maximum 50 kW of nominal heat output. These requirements apply to heating appliances according to of ÖNORM EN 1, ÖNORM EN 12815, ÖNORM EN 13229, ÖNORM EN 13240, ÖNORM EN 14785 and ÖNORM EN 15250 as well as to individually planned plants according to ÖNORM EN 15544.



Subsector H26: SEALING MATERIALS



ICS :National Ref : 03200807Title : Sealants for gas supply; sealing materials of rubber, cork and synthetic fibres for gas

armatures and gas appliances; safety requirements, tests



Page 22


ICS :National Ref : 03200809Title : Materials for the subsequent sealing of joints in underground gas mains - Part 1: Plastic

foil and textile fibre linings used to seal gaspipes already in place; safety requirements and testing



Subsector H27: EDUCATIONAL EQUIPMENT



ICS :National Ref : 09500451Title : Satchels - Requirements and testing



Subsector H30: EQUIPMENT FOR CHILDREN

Subsector : H30 Registration Date : 2017-11-28Organization : UNICountry : Italy


ICS : 97.190National Ref : UNI1603279Title : Child use and care articles - Baby carriers - Safety requirements and test methods –

Baby slingsScope : This Standard specifies the safety requirements and test methods for baby slings without a

framedsupportdesignedtocarryachildwhenattachedtothecarer’storso.This standard applies to the following product categories: baby wrap; one-shoulder baby sling;meitai.This Standard does not apply to products covered by EN 13209-2. Baby slings are designed to allow the carer a hands free operation when standing and/or walking. These slings are for useuptoamaximumweightof18kg.


Subsector : H30 Registration Date : 2017-11-28Organization : UNICountry : ItalyProject ID : 01603838/0001 Project

Page 23

EstablishedICS : 97.190National Ref : UNI1603838Title : Child use and care articles - Baby carriers - Safety requirements and test methods – Soft

carrier without incorporated integral leg openingsScope : This Standard specifies the safety requirements and test methods for soft carriers without a

framed support and without incorporated integral leg openings designed to carry a child whenattachedtothecarer’storso.This Standard does not apply to products covered by EN 13209-2. Children slings are designed to allow the carer a hands free operation when standing and/or walking. These slingsareforuseuptoamaximumweightof18kg.



** End of Sector **






Page 25Subsector I02: FASTENERS



ICS : 21.060.70National Ref : DIN 3016-1Title : Fastening clamps - Part 1: With tongue




ICS :National Ref : 06702299Title : Round wire snap rings for shafts




ICS :National Ref : 06702300Title : Round wire snap rings for bores




ICS :National Ref : 06702301Title : Snap rings with rectangular profile for shafts


Subsector : I02 Registration Date : 2017-11-17Organization : DIN

Page 26

Country : Germany


ICS :National Ref : 06702302Title : Snap rings with rectangular profile for bores



Subsector I04: ROLLING BEARINGS



ICS : 21.100.20National Ref : ÖNORM M 6320-1 Beiblatt 2Title : Rolling bearings - Explanation of the calculation method of the dynamic load rating and

basic rating lifeScope : This supplement provides additional background information on the derivation of formulas

and factors specified in ÖNORM M 6320-1 and ISO 281-1:2007 " Rolling bearings - Dynamic load ratings and rating life".



Subsector I06: PRESSURE VESSELS

Subsector : I06 Registration Date : 2017-11-27Organization : LVS Draft Issue Date : 2017-11-28Country : Latvia Latest Date for Comments : 2018-01-26


ICS : 23.020.30National Ref : prLVS 416Title : Boiler equipment. Safety examination of existing assembliesScope : Standart defines the procedures of the technical supervision of the new and used boilers

installations. Standart is rrelevant relevant to the inspection`s institutions what according with the normative acts carry out the technical supervision. Sandart allows to make controls and defines the safety level of the boilers installation.




Page 27

ICS : 23.020.30, 27.060.30National Ref : UNI1603813Title : Pressure equipment - Putting into service and use of pressure equipment and assemblies

- Part 10: Supervision of steam boilers and/or super-heated water generators excluded from the scope of UNI/TS 11325-3

Scope : This technical specification provides procedures for the supervision of fired or otherwise heated pressure equipment with the risk of overheating, intended for generation of steam and/or super-heated water at temperatures higher than 110 °C (“steam boilers and/or hot water generators”) at a maximum allowable pressure PS greater than 0,5 bar included in the scope of the Italian decree D.M. 329/2004 and excluded from the scope of UNI/TS 11325-3, and,also,havingthefollowingrequirements:a) unfired steam boilers and/or hot water generators in which the design temperature of the pressure bearing parts, that will come into contact with the heating fluid, is not lower than theheatingfluiditself;b)lowcapacityforced-circulationsteamboilersand/orhotwatergeneratorshavingPSxV≤3000bar·LandPS≤12bar;c)lowpressuresteamboilershavingPS≤1bar,heatingarea≤100m2andcapacity≤2t/h;d)lowpressurehotwatergeneratorshavingPS≤5bar,watermaximumtemperature≤120°Candcapacity≤2t/h;e)electricallypoweredsteamboilersand/orhotwatergenerators.The technical specification gives recommendations of operation and testing of the boiler both with and without the continuous presence of the boiler attendant, with a maximum time of operation without manual intervention of 72 hours.



Subsector I13: GAS CONTAINERS

Subsector : I13 Registration Date : 2017-11-10Organization : NSAICountry : Ireland


ICS : 75.160.30National Ref : I.S. 3213:201xTitle : Code of Practice for the Storage of LPG Cylinders and CartridgesScope : This code applies to the keeping of LPG in containers where the total quantity stored

exceeds 15kg, but the general principles may be used when keeping smaller quantities. It also applies to containers on loaded vehicles parked other than on a public highway. The requirements of the Building regulations shall take precedence over any requirements of this Code.The contents of this document represent the general requirements for the safe storage of LPG cylinders and cartridges. However in specific circumstances the fire authorities may find it necessary ti impose additional safeguards.



Subsector I19: NUCLEAR ENERGY

Subsector : I19 Registration Date : 2017-11-21

Page 28

Organization : ASICountry : Austria


ICS : 11.040.50National Ref : ÖNORM S 5240-12Title : Image quality assurance in X-ray diagnosis - Part 12: Acceptance testing of

mammographic X-ray equipmentScope : This ÖNORM contains parameter for acceptance testing of digital mammography systems,

describes testing methods, and defines extreme values as well as testing periods.




ICS : 11.040.50, 11.060.20National Ref : ÖNORM S 5240-5Title : Image quality assurance in X-ray diagnostics - Part 5: Constancy test in dental

radiographic technologyScope : This ÖNORM describes the constancy test in dental radiographic technology.




ICS : 11.040.50National Ref : ÖNORM S 5240-11Title : Image quality assurance in X-ray diagnosis - Part 11: Acceptance testing of dental

radiographic equipment - Limit valuesScope : This ÖNORM describes testing methods, parameter, extreme values for acceptance testing

on analog and digital dental radiographic equipment including DVT and defines testing periods.




ICS : 11.040.50National Ref : ÖNORM S 5240-7Title : Image quality assurance in X-ray diagnostics - Constancy testing on medical X-ray

equipments for mammographyScope : This ÖNORM contains parameter for constancy testing of digital mammography systems,

Page 29

describes testing methods, and defines extreme values as well as testing periods.



Subsector I99: UNDETERMINED



ICS :National Ref : 01200665Title : Dispense systems for draught beverages - Part 1: General requirements



** End of Sector **






Page 31Subsector N01: PAPER AND BOARD



ICS : 85.080, 85.080.10National Ref :Title : Facsimile papersScope : This standard specifies the roll and sheet papers used to record in facsimile machines.



Subsector N03: PETROLEUM PRODUCTS



ICS :National Ref : 06235092Title : Lubricants - Lubricating oils - Part 3: Lubricating oils CLP, Minimum requirements




ICS :National Ref : 06235158Title : Testing of liquid fuels - Determination of bromine acceptance by electrometric Dead-

Stop-method of samples with a bromine acceptance of more than 0,5 g/100 g (BA)




ICS :National Ref : 06235260Title : Lubricants - Lubricating oils - Part 1: Lubricating oils C, Minimum requirements


Page 32



ICS :National Ref : 06235261Title : Lubricants - Lubricating oils - Part 2: Lubricating oils CL, Minimum requirements




ICS : 75.100National Ref :Title : Lubricating oils, industrial oils and related products (Class L) - Base oilsScope : This standard specifiee requirements and test methods for base oils



Subsector N05: TEXTILES



ICS : 59.080.30National Ref : DIN 53894-2Title : Testing of textiles - Determination of dimensional change of textile fabrics - Part 2:

Steaming on ironing machines



Subsector N06: RUBBER



ICS : 83.060National Ref : ÖNORM ISO 2230

Page 33

Title : Rubber products - Guidelines for storage (ISO 2230:2002)Scope : This International Standard gives guidelines for the inspection, recording procedures,

packaging and storage of products, assemblies and components made from vulcanized or thermoplasticrubberpriortobeingputintocirculation.It is applicable to both solid and cellular rubber products prepared from dry raw rubber, latex or other sources.



Subsector N09: PLASTICS



ICS :National Ref : 06235142Title : Testing of adhesives for metals and adhesively bonded metal joints - Determination of

the resistance to liquids






ICS :National Ref : 05401941Title : Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) for cable ducting -

Dimensions and technical delivery conditions




ICS :National Ref : 05401942Title : Pipes of high-density polyethylene (PE-HD) for buried telecommunication - Dimensions

and technical delivery conditions


Page 34


** End of Sector **






Page 36Subsector S04: PROTECTIVE CLOTHING AND EQUIPMENT

Subsector : S04 Registration Date : 2017-11-27Organization : SIS Draft Issue Date : 2018-01-23Country : Sweden Latest Date for Comments : 2018-01-23


ICS : 11.140National Ref : 8760123Title : Health care textiles - Dress for staffScope : This standard specifies requirements, design and cutting patterns for dress for stafff in health

care.


Subsector : S04 Registration Date : 2017-11-27Organization : SIS Draft Issue Date : 2018-01-23Country : Sweden Latest Date for Comments : 2018-01-23


ICS : 11.140National Ref : 8760125Title : Health care textiles - Maternity trousers for staffScope : This standard specifies requirements, design and cutting patterns for maternity trousers for

staff in health care.



Subsector S07: ANAESTHETIC AND RESPIRATORY EQUIPMENT



ICS : 11.040.10National Ref : UNI1603600Title : Pipeline systems for compressed medical gases and vacuum - Terminal units for

compressed medical gases and vacuumScope : This standard applies to terminal units in compliance with UNI EN ISO 9170-1 that are

intended to be used in pipeline systems for compressed medical gases and vacuum. This standard specifies dimensions of probes, sockets and gas specific connections points.

Relatedness :National : REV/AMD UNI 9507:2004;UNI 9507:2004


Subsector S08: AIR QUALITY

Subsector : S08 Registration Date : 2017-11-09Organization : NEN

Page 37

Country : Netherlands


ICS : 81.060.30National Ref : NEN 9102:2017 Concept nlTitle : Ceramic fibres - Determination of the presence and the concentration of respirable

refractory ceramic fibres Scope : NEN 9102 describes a method for: - the sampling and determination of the presence of

respirable refractory ceramic fibres; - the sampling and determination of the presence of the concentration of and exposure to respirabe refractory ceramic fibres.






ICS :National Ref : 11904269Title : German standard methods for the examination of water, waste water and sludge - Sludge

and sediments (group S) - Part 18: Determination of adsorbed organically bound halogens (AOX) (S 18)





and sediments (group S) - Part 15: Determination of the specific residual beta activity a<(Index)R><Index beta>in sludge, sediment and suspended matter (S 15)





and sediments (group S) - Part 22: Determination of dry residue by freezing and

Page 38

preparation of the freeze dried mass of sludge (S 22)




ICS : 13.060.70National Ref : NEN 9406:2017 Concept nlTitle : Water - Methods in hydrobiology - Field analyses of macrofytes Scope : NEN 9406 describes the method for the analysis of samples of macrofytes in the field, the

processing of the collected data and the reporting of the metadata.



Subsector S24: SOIL QUALITY



ICS : 13.080.10National Ref : ÖNORM L 1087Title : Chemical analysis of soils - Determination of "plant-available" phosphorus and potassium

by the calcium-acetate-lactate (CAL)-methodScope : This Austrian Standard is used for the determination of the von "plant-available" phosphorus

and potassium in soils with pH >= 6. Excepted are soils used for forestal purposes.




ICS : 13.080.20National Ref : ÖNORM L 1061Title : Physical analysis of soils - Determination of particle size distribution in mineral soilsScope : This ÖNORM is to be used for the determination of the mass fractions of grain size classes of

the mineral soil.



** End of Sector **






Page 40Subsector T03: ROAD VEHICLES

Subsector : T03 Registration Date : 2017-11-17Organization : TSECountry : Turkey


ICS : 43.060.20National Ref :Title : Road Vehicles - Exhaust Pipes Muffler Scope : This standard covers exhaust pipes muffler used in road vehicles except motorcycle, moped,

tructors and military vehicles.

Relatedness :National : NewInternational : Modified SAE J 261:1987












Subsector T09: MATERIALS HANDLING AND STORAGE EQUIPMENT

Subsector : T09 (Secondary Subsector)




Page 41

ICS : 91.100.10National Ref :Title : Principles of Bulk Cement TransportationScope : This standard specifies the principles of transferring cement from the production line to the

transporting vehicle, transportation and preservation of the quality of bulk cement during these stages.



Subsector T14: PACKAGING

Subsector : T14 Registration Date : 2017-11-17Organization : DINCountry : Germany


ICS :National Ref : 11501223Title : Packaging test - Compression test - Part 1: Test with a constant conveyance-speed




ICS :National Ref : 11501224Title : Packaging test - Leakage test on flexible packagings - Part 2: Colour method




ICS :National Ref : 11501225Title : Packaging test - Leakage test on flexible packagings - Part 3: Pressure drop method



Subsector T19: ROAD SAFETY

Page 42

Subsector : T19 Registration Date : 2017-11-13Organization : ASROCountry : Romania

Project ID : 001848-1/0002 Project Established

ICS : 93.080.01National Ref : SR 1848-1:2018Title : Road signalisation. Road traffic signs and signalisation tools Part 1: Classification,

symbols and locations

Relatedness :National : REV/AMD SR 1848-1:2011



ICS : 93.080.01National Ref : SR 1848-2:2018Title : Road signalisation. Road traffic signs and signalisation tools Part 2: Technical

requirements




ICS : 93.080.01National Ref : SR 1848-3:2018Title : Road signalisation. Road traffic signs and signalisation tools. Part 3: Design and

description



** End of Sector **




Sector X : UNDETERMINED STANDARDIZATION AREA


Page 44




Sector Z : INFORMATION TECHNOLOGY


Page 46Subsector Z99: UNDETERMINED

Subsector : Z99 Registration Date : 2017-11-28Organization : UNICountry : Italy


ICS : 35.020National Ref : UNI1603705Title : Enabling Technologies for Industry 4.0 – Integration and interconnection: main issues

and examplesScope : The Technical Report specifies operational definitions, and provides clarification and

examples to foster a convergent and converging interpretation of integration and interconnectionrequirements.The technical report introduces some definitions, provides some guidance on the main architectures and needs to be analyzed in the implementation of an integrated and connectedsystem,andsomesimplecases.



** End of Sector **

2011-06


Sector A: Services


reference reference


















reference reference


B02 Structures 59; 98 166; 167; 250; 277; 346; 349; 284; 288; 297; 340


B04 Cement 74; 77 51


B06 Gypsum / 241

B07 Glass 160 129





B12 Masonry 179; 196 125; 246




B16 Taps / /





B21 Baths / /

















reference reference





C05 Lac / /


C08 Pesticides 81 /


C10 Starch 93 /

C11 Tobacco 126 401

C12 Glass plant / /




C18 Adhesives / 193








reference reference




F04 Sieves 24 /


294; 318; 244; 367; 141; CEN/WS 011



F08 Surfaces / 290

F09 Banking 68 /

F10 Statistics 69 /








F19 Optics 172; 187 123; 170









reference reference






H06 Horology 114 /

H07 Space heating 116 62; 110; 130; 179; 180








H15 Toys 181 52

H17 Oil stoves / 46




H23 Ladders / 93





H28 Hunting 191 /







H99 Undetermined / 299; 364; 369; 402



reference reference


I02 Fasteners 2 185





I07 Shafts 14 /



I10 Splines / /

I11 Machine tools 39 142; 143; 145; 255



I14 Gears 60 /




I18 Mining 82 196





I23 Pumps 115 197








I31 Valves 153; 185 69; 236; 105

I32 Flanges / 74
















reference reference


M02 Zinc / 209


M04 Copper 26 133

M05 Welding 44 121




M09 Iron ores 102 /





M14 Nickel 155 /











reference reference





N05 Textiles 38 189; 248

N06 Rubber 45 218; 366 CEN/WS 003


N08 Mica / /

N09 Plastics 61 249

N10 Cork 87 /



N13 Leather 120 289


N17 Fluorspar 175 /


N19 Tapes / 253




N23 Diamond / 410




reference reference



S03 Syringes 84 /





























reference reference




T04 Tyres 31 /

T05 Pallets 51 /



T08 Cranes 96 147






T14 Packaging 122 261; 120

T15 Cycles 149 333
















Documents

Λειτουργό Διοίκησης (CYS) · 2021. 1. 8. · Information procedure Page 1 Monthly Notifications Register Notifications registered at CCMC from 2017-08-01 to 2017-08-31