Operating and Installation Instructions Gas cooktop

Operating and InstallationInstructionsGas cooktop

To prevent accidents and machine damage, read these instructionsbefore installation or use.

en-US, CA M.-Nr. 06 818 490

IMPORTANT SAFETY INSTRUCTIONS

2

WARNING: If the information in this manual is not followed exactly, a fire orexplosion may result causing property damage, personal injury, or death.

- Do not use or store gasoline or other combustible liquids or vapors in the vicinityof this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

– Do not try to light any appliance.

– Do not touch any electric switches.

– Do not use any phones inside your building.

– Immediately call your gas supplier from a neighbor's phone. Follow the gassupplier's instructions.

– If you are unable to reach your gas provider, call the fire department.

- Installation and service must be performed by a qualified installer, qualified ser-vice agency or your gas provider.(In Massachusetts, installation must be performed by a licensed installer / gasfitter.)

- Note to the installer:Please give these installation instructions to the consumer for the local electri-cal/gas inspector.

WARNING: Never Operate the Top Surface Cooking Section of this Appli-ance Unattended.

- Failure to follow this warning statement could result in fire, explosion, or burnhazard that could cause property damage, personal injury, or death.

- If a fire sould occur, keep away from the appliance and immediately call your firedepartment.

DO NOT ATTEMPT TO EXTINGUISH AN OIL/GREASE FIRE WITH WATER.

® ®

Contents

3

IMPORTANT SAFETY INSTRUCTIONS ............................................................ 2

IMPORTANT SAFETY INSTRUCTIONS ............................................................ 5

Caring for the environment .............................................................................. 16

Overview............................................................................................................. 17Cooktop............................................................................................................... 17

KM 3464, KM 3465 ........................................................................................ 17KM 3474, KM 3475 ........................................................................................ 18KM 3484, KM 3485 ........................................................................................ 19

Control knobs...................................................................................................... 20Included accessories........................................................................................... 22

Before first use .................................................................................................. 23Cleaning the cooktop for the first time................................................................ 23Turning on the cooktop for the first time ............................................................. 23

Cookware ........................................................................................................... 24

Energy saving tips ............................................................................................ 25

Operation............................................................................................................ 26Rapid ignition system.......................................................................................... 26Wok burner.......................................................................................................... 26Turning the appliance on ..................................................................................... 27Adjusting the flame.............................................................................................. 28

Visual characteristics gas flames ................................................................... 28Switching off........................................................................................................ 28

Safety features................................................................................................... 29

Cleaning and care ............................................................................................. 30Stainless-steel cooktop....................................................................................... 31Grates.................................................................................................................. 31Control knobs...................................................................................................... 31Burner.................................................................................................................. 32

Cleaning the burners ...................................................................................... 32

Frequently Asked Questions ............................................................................ 35

Optional accessories ........................................................................................ 37

Customer Service .............................................................................................. 38Contact in the event of a fault ............................................................................. 38Appliance warranty and product registration ...................................................... 38

Contents

4

Installation.......................................................................................................... 39IMPORTANT SAFETY INSTRUCTIONS - INSTALLATION ................................... 39Safety distances.................................................................................................. 40Installation notes ................................................................................................. 41Installation dimensions........................................................................................ 42

KM 3464, KM 3465 ........................................................................................ 42KM 3474, KM 3475 ........................................................................................ 43KM 3484, KM 3485 ........................................................................................ 44

Installation ........................................................................................................... 45Gas connection ................................................................................................... 47Burner ratings...................................................................................................... 50Electrical connection ........................................................................................... 52

MieleCare ........................................................................................................... 54


5

This cooktop complies with all relevant local and national safetyrequirements. Inappropriate use can, however, lead to personal in-jury and material damage.

Read the operating and installation instructions carefully beforeusing the cooktop. They contain important information on safety,installation, use and maintenance. This prevents both personal in-jury and damage to the cooktop.

When installing the cooktop, Miele expressly and strongly advisesthat you read and follow the instructions under “Installation”, aswell as in the “IMPORTANT SAFETY INSTRUCTIONS”.

Miele cannot be held liable for injury or damage caused by non-compliance with these instructions.

Keep these instructions in a safe place and pass them on to anyfuture owner.


6

Appropriate use

This cooktop is intended for domestic use and use in other similarenvironments.

This cooktop is not intended for outdoor use.

The cooktop is intended for domestic use only to prepare foodand keep it warm. Any other use may be dangerous.

Persons (including children) who lack physical, sensory or mentalabilities, or experience with the appliance should not use it withoutsupervision or instruction by a responsible person.


7

Safety with children

As with any other appliance, children must be supervised.

Do not leave children unattended: Children should not be alone orunsupervised in the area where the appliance is installed. Do not al-low them to sit or stand on the appliance.

Be sure to supervise any children in the vicinity of the cooktop,and do not let them play with it.

The cooktop gets hot when in use and remains hot for some timeafter being turned off. Keep children away from the appliance until ithas cooled down and is no longer a burn hazard.

Danger of burning. Do not store anything which might arouse achild’s interest in storage areas above or behind the cooktop. Other-wise they could be tempted to climb onto the appliance.

Risk of burning or scalding. Turn pot and pan handles inward, sochildren cannot pull them down and be burned.

Danger of suffocation. While playing, children may become entan-gled in packaging material (such as plastic wrapping) or pull it overtheir head, presenting the risk of suffocation. Keep packaging mate-rial away from children.


8

Technical safety

Unauthorized installation, maintenance, and repairs can causeconsiderable danger for the user. Installation, maintenance, and re-pairs must only be carried out by a Miele authorized technician.

Maintenance by the user: Never repair or replace any part of theappliance unless the instructions specifically recommend doing so.Service work should only be performed by a qualified technician.

Damage to the cooktop can compromise your safety. Check thecooktop for visible signs of damage. Do not use the cooktop if it isdamaged.

Reliable and safe operation of the cooktop can only be guaran-teed if it is connected to the public power supply.

Be certain your appliance is properly installed and grounded by aqualified technician. To guarantee the electrical safety of this appli-ance, continuity must exist between the appliance and an effectivegrounding system. It is imperative that this basic safety requirementbe met. If there is any doubt, have the electrical system of the housechecked by a qualified electrician.

Proper installation: Make sure that your appliance has been in-stalled correctly and that it has been grounded by a qualified techni-cian.

To avoid damaging the cooktop, make sure that the connectiondata (voltage and frequency) on the data plate correspond to thebuilding's power supply before connecting the appliance.When in doubt, consult a qualified electrician.

Do not connect the appliance to the electrical supply with a powerbar or extension cord. These are a fire hazard and do not guaranteethe required safety of the appliance.

For safety reasons, the cooktop may only be used when it hasbeen fully installed.


9

This appliance must not be used in a non-stationary location (e.g.on a ship).

Any contact with live connections or tampering with the electricalor mechanical components of the cooktop will endanger your safetyand may lead to appliance malfunctions.Do not open the casing of the cooktop under any circumstances.

Any repairs not performed by a Miele authorized service techni-cian will void the warranty.

Defective components should be replaced by Miele original partsonly. Only with these parts can safety of the appliance be assured asintended by the manufacturer.

The appliance is not intended for use with an external timer switchor a remote control system.

The connection to the gas supply must be carried out by a quali-fied service technician in accordance with current local and nationalsafety regulations (see “Installation – Gas connection”). If the plughas been removed or the power cord is not supplied with a plug, thecooktop must be connected to the power supply by a qualified ser-vice technician (see “Installation – Electrical connection”).

If the power cord is damaged, it must only be replaced by a quali-fied service technician (see “Installation – Electrical connection”).

During installation, maintenance, and repair work, the appliancemust be completely disconnected from the household electricitysupply. The gas supply must be shut off. Ensure that this is the caseby:

- removing the fuse

- “tripping” the circuit breaker, or

- unplugging the unit. Pull the plug not the cord.

- Shut off the gas supply.


10

Danger of electric shock.If the cooktop is defective, immediately turn the appliance off anddiscontinue use. Disconnect it from the electricity and gas supply.Contact Technical Service.

If the cooktop is installed behind a cabinet (e.g., a door), do notclose the cabinet door while the cooktop is in operation. Heat andmoisture can build up behind the cabinet door when closed. Thiscan result in damage to the cooktop, housing unit, and floor. Leavethe cabinet door open until the cooktop has cooled down com-pletely.

Reaching over a hot cooktop to access the cabinets can result inburns. You can reduce the risk of burns by installing a ventilationhood that extends at least 4¾" (12 cm) past the bottom of the cabi-nets.

Ask your installer to show you the location of your gas shutoffvalve and fuses or circuit breaker panel in your apartment or home.Be sure that you know how and where to disconnect the gas andpower supply to your cooktop.


11

Correct use

The cooktop gets hot when in use and remains hot for some timeafter being turned off. Do not touch the appliance if there is a possi-bility that it could still be hot.

When in use, the cooktop emits a significant amount of heat,which can cause objects in the vicinity to catch fire.Never use the cooktop to heat the room.

Do not leave the cooktop unattended when cooking on highpower. Spilled food will begin to smoke and cause grease splatter,which can ignite on the cooktop. Doing so may result in carbonmonoxide poisoning and overheating of the appliance.

Oil and fat can catch fire if overheated. Never leave the applianceunattended when cooking with oil and fat. If the oil or fat catchesfire, do not attempt to put the flames out with water.Turn off the cooktop and smother the flames using a lid or a suitablefire blanket.

Smother the fire or flames, or use a dry chemical extinguishingagent or foam fire extinguisher.

The flames could set the grease filters of a ventilation hood on fire.Do not flambé under a ventilation hood.

Spray canisters, aerosols and other inflammable substances canignite when heated. Therefore do not store such items or substancesin a drawer under the appliance. Cutlery inserts must be heat-resis-tant.

Never heat empty cookware.

Do not heat or can food in closed containers, such as tins orsealed jars, on the cooktop, as pressure will build up in the containerand cause it to explode.


12

If the cooktop is covered, there is a risk that the material of thecover will ignite, explode or melt if the cooktop is still hot or if turnedon inadvertently. Never cover the cooktop with a board, cloth or pro-tective sheet.

When the appliance is turned on inadvertently or by mistake, orwhen there is residual heat present, there is a risk of the metal itemsheating up. Other materials can melt or catch fire when the applianceis switched on. Do not store items on the cooktop.

You can burn yourself on a hot cooktop. When cooking on the ap-pliance, protect your hands by using heat-resistant pot holders oroven mitts. Only use dry pot holders or gloves. Wet or damp textilesconduct heat more effectively and produce steam, which poses aburn hazard. Be sure to keep all textiles away from the gas flames.Do not use oversized cloths, dish towels or other similar materials.

When using an electrical appliance, e.g. a hand mixer, near thecooktop, make sure that the power cable does not come into con-tact with the hot cooktop. The cable's insulation could become dam-aged.

Cookware made of plastic or aluminum foil will melt at high tem-peratures. Do not use any plastic or aluminum foil cookware.

Pressing the knob generates a spark on the ignitor. Do not pressthe knob while you are cleaning or touching the cooktop or a burnerin the vicinity of an ignitor.

A ventilation hood installed above the cooktop can become dam-aged or catch fire as a result of intense heat. Do not use the gasburners without cookware.

Only light the gas burners after all burner parts have been properlyassembled.


13

If the cookware is too small, it will not sit properly on the burnergrate. If the cookware is too large, heat emitted from the bottom ofthe cookware may damage the countertop, walls with poor heat-re-sistance (e.g. paneled walls) or portions of the cooktop.

Make sure that the burner flames do not extend beyond the bot-tom of the cookware and rise up its sides.

Only use cookware with a thick enough bottom. Failure to do somay result in damage to the cooktop.

Always use the burner grates supplied with the cooktop. Neverplace cookware directly on the burner.

Install the burner grates in an upright position to avoid scratchingthe cooktop.

Storage in or on the appliance: Flammable materials should not bestored in an oven or in the vicinity of the cooktop.

Remove all grease splatters and other flammable (food) residueson the cooktop. They are a fire hazard.

Avoid allowing liquids or foods containing salt to spill onto thecooktop. If salty foods or liquids do get on the cooktop, they shouldbe removed as soon as possible to avoid the risk of corrosion.

Using of a gas cooktop causes heat, moisture and products ofcombustion to build up in the room in which it is installed. Make surethat your kitchen is well ventilated, especially when the appliance isin use: keep any natural means of ventilation open or install a me-chanical ventilation system (e.g. a ventilation hood).

If the cooktop is used for very long periods of time, additionalventilation of the room may be necessary, e.g. by opening windowsor doors, or running the ventilation on the highest setting.

Do not use pots or pans that are large enough to cover severalburners. The resulting heat buildup can damage the appliance.


14

If the cooktop has not been used for a long period of time, be sureto thoroughly clean it and have it inspected by an authorized techni-cian before using it again.

Ensure that the igniters are clean and dry to allow the burners toignite and burn properly.

Fire hazard! Loose-fitting or hanging garments can catch fire. Besure to wear appropriately fitting clothing when cooking. Never allowloose clothing or flammable materials to come into contact with theburners while the burners are in use.

When you have finished cooking, make sure that the burners areturned off by checking the position of the knobs.

The grates, burner cap, bottom parts of the burner, and any otherparts located near the burner flame, can still be very hot after cook-ing and cause burns. Do not touch these components when usingthe cooktop.

Wind can blow curtains over the cooktop, causing them to catchfire. If the cooktop is installed near a window, do not use long cur-tains.

Only certain types of glass, ceramic or other enamel cookwarecan be used on a gas cooktop without breaking as a result of sud-den temperature changes.

Wet sponges or clothes can cause burns due to hot steam if theyare used to wipe spilled food off a hot burner. Some cleansers canemit hazardous vapors if they are applied to a hot surface. Be carefulwhen cleaning the cooktop.


15

Cleaning and maintenance

Do not use a steam cleaner to clean the cooktop.The steam may reach electrical components and cause a short cir-cuit.

Miele will guarantee to supply functional parts for a minimum of10 years and up to 15 years following the discontinuation of yourcooktop.

SAVE THESE INSTRUCTIONS AND REVIEW THEM PERIODICALLY

Caring for the environment

16

Disposal of the packing mate-rialThe cardboard box and packing materi-als protect the appliance during ship-ping. They have been designed to bebiodegradable and recyclable.

Ensure that any plastic wrappings,bags, etc. are disposed of safely andkept out of the reach of children. Dan-ger of suffocation!

Disposal of your old applianceElectrical and electronic appliancescontain valuable materials. They alsocontain certain substances, compoundsand components which were essentialfor the proper functioning and safe useof the equipment. Handling these mate-rials improperly by disposing of them inyour household waste can be harmful toyour health and the environment. There-fore, please do not dispose of your oldappliance with regular household wasteand follow local regulations on properdisposal.

Consult with local authorities, dealers orMiele in order to dispose of and recycleelectrical and electronic appliances.Miele assumes no responsibility fordeleting any personal data left on theappliance being disposed. Please en-sure that your old appliance is keptaway from children until removal. Ob-serve safety requirements for appli-ances that may tip over or pose an en-trapment hazard.

Overview

17

Cooktop

KM 3464, KM 3465

a Wok ring

b Normal burner

c Power burner

d Grates

e Wok burner

Knobs for the cooking zones

f Front left

g Front right

h Back right

i Back left

Overview

18

KM 3474, KM 3475

a Wok ring

b Normal burner

c Power burner

d Grates

e Wok burner

The knobs are arranged according to the arrangement of the burners

Overview

19

KM 3484, KM 3485

a Wok ring

b Normal burner

c Power burner

d GratesThe design of the grates depends onthe cooktop model

e Large wok burner

f Small wok burner

Knobs for the cooking zones

g Front right

h Front middle

i Front left

j Back right

k Back middle

l Back left

Overview

20

Control knobs

Economy, normal, and power burners

Symbol Description

Burner off, the gas supply is turned off

Strongest flame

Weakest flame

Overview

21

Wok burner

a Burner offThe gas supply is turned off

b Strongest flameThe outer and inner burners are on the highest setting

c Strong flameThe outer burner is on the lowest setting, the inner burner on the highest setting

d Over-ignition positionThe outer burner is ignited by changing from the lowest to the highest setting

e Weak flameThe outer burner is off, the inner burner is on the highest setting

f Weakest flameThe outer burner is off, the inner burner is on the lowest setting

Overview

22

Included accessoriesThe accessories supplied with your ap-pliance, as well as a range of optionalones, are available to order from Miele(see “Optional accessories”).

Wok ring

The Wok ring supplied with your appli-ance can be used in instances whereextra stability is required. It is particu-larly suitable for wok pans with roundedbases.

Before first use

23

Cleaning the cooktop for thefirst time Before first use, wipe down the appli-

ance with a damp cloth and dry it.

Using a soft sponge, clean all remov-able burner parts with a solution ofwarm water and a small amount ofliquid dish soap. Dry the parts thor-oughly after cleaning and reassemblethe burners (see “Cleaning andcare”).

Turning on the cooktop for thefirst timeMetal components are protected by aconditioning agent. Smells and vapormay occur when the appliance is usedfor the first time.

The smell and any vapors do not indi-cate a faulty connection or a defectiveappliance and are not harmful to yourhealth.

Cookware

24

- Select cookware that fits the size ofthe burner:Large diameter = large burnerSmall diameter = small burner

- Using cookware that is too large cancause the flames to spread out anddamage the surrounding countertopor other appliances. Choosing theright cookware size improves effi-ciency.

- Any cookware that has a diametersmaller than the burner grate orwhich does not rest in a stable posi-tion on the grate (without wobbling) isdangerous and should not be used.

- Unlike cookware that is used on anelectric cooktop, the bottom of cook-ware used on a cooktop does nothave to be flat to deliver effectivecooking performance.

- When purchasing pots and pans,keep in mind that the diameter indi-cated is typically the top diameter,not the bottom diameter.

- All heat-resistant cookware is suitablefor use.

- Cookware with a thick bottom ispreferable, as it distributes heat moreevenly. Cookware with a thin bottommay cause food to overheat in certainspots. To avoid this, stir the food fre-quently.

- Always place the cookware on thepot rests supplied. Do not placecookware directly on the burners.

- Position the cookware on the burnergrate so that it cannot tip. There is al-ways a possibility of a slight tilt, de-spite the proper position.

- Do not use pots or pans that havebottoms with pronounced edges.

Energy saving tips

25

- Whenever possible, keep pots andpans covered while cooking. Doingso will prevent unnecessary heat loss.

- Wide, shallow cookware heats upfaster and is therefore preferable totall, narrow cookware.

- Cook with as little water as possible.

- Reduce the power setting once thewater has come to a boil or the oil/fatis hot enough for frying.

- Use a pressure cooker to reduce thecooking time.

Operation

26

Fire hazard due to overheatedfood.Unattended food can overheat andignite.Do not leave the cooktop unattendedwhilst it is being used.

Rapid ignition systemThe cooktop is supplied with a rapid ig-nition system with the following fea-tures:

- Rapid ignition without the need tohold the knob.

- Automatic re-ignitionIf the flame is extinguished by a draft,for example, the burner is automati-cally relit. If re-ignition is unsuccess-ful, the gas supply is automaticallycut off (see “Safety features” – “Igni-tion safety”).

If there has been a power outage, theautomatic re-ignition feature will notwork properly.

Wok burnerYou can place a wok pan on the wokburner without an additional wok ring.

If you are using the wok ring, place iton the grate so that it sits securely inposition and cannot move (see dia-gram).

Operation

27

Turning the appliance on Press the knob lightly and turn it

counter-clockwise to the large flamesymbol.

Then press it down firmly to open thegas supply and let it go.

The ignition electrode “clicks” and ig-nites the gas.

When a knob is activated, a spark isdeveloped automatically on all burn-ers. This is normal and does not indi-cate a fault.

If the burner does not ignite, turn theknob to the position. Ventilate theroom or wait for at least 1 minute be-fore trying again.

If the burner does not ignite the sec-ond time, turn the knob back to the position and see “Frequently askedquestions”.

Brief re-ignition may occur duringswitch-on (1–2 x clicks), e.g., if there isa draft.

Switching on during a power outage

In case of a power outage, the flamecan be ignited manually.

Press in the relevant control knob andturn it counterclockwise to the largeflame symbol.

Hold the control knob pressed downand light the gas at the burner with amatch.

Keep the control knob pressed downfor a further 5–10 seconds and thenrelease it.

Operation

28

Adjusting the flameThe burners can be variably adjustedbetween the lowest and highest flamesettings.

Because the edges of the flame aremuch hotter than its center, the flametips should stay beneath the bottom ofthe cookware. Flame tips which ex-tend beyond the sides of the cook-ware emit unnecessary heat into theroom and can also damage cookwarehandles, which increases the risk ofinjury.

Adjust the flame so that it never ex-tends up the sides of the cookware.

Wok burner

Depending on the knob design, theremay be a stopper at the 6 o’clock posi-tion to prevent you turning the knob tothe high or low setting unintentionally.

Press the knob down lightly to movepast this stopper.

Visual characteristics gas flames

Yellow flames

Contact the MieleService Depart-ment.

Yellow tips onouter cones

Normal forpropane gas

Soft blue flamesyellow colour isonly allowed atthe tip of the innercone

Normal for naturalgas

Switching off Turn the control knob clockwise to

the position.

This stops the flow of gas and the flamegoes out.

Safety features

29

Ignition safetyThe cooktop is equipped with an igni-tion safety device. If a gas flame is ex-tinguished (e.g., by food boiling over orby a draft) and re-ignition does notwork, the gas supply is switched off.This prevents the release of gas. If youturn the knob to the position, theburner is ready for use again.

The flame failure device operates inde-pendently from the electricity supply.This means that it will still work if thecooktop is used during a power out-age.

Cleaning and care

30

Danger of burning due to hotsurfaces.The cooktop surface, grates, andburners will be hot after use.Allow the cooktop to cool down be-fore cleaning it.

Risk of damage due to moistureingress.The steam from a steam cleaning ap-pliance could reach electrical com-ponents and cause a short circuit.Do not use a steam cleaner to cleanthe cooktop.

All surfaces could be discolored ordamaged if unsuitable cleaningagents are used. All surfaces aresusceptible to scratching.Remove all cleaning agent residuesimmediately.Do not clean with any abrasive orsharp pointed objects.

Food boiling over can cause discol-oration of the burner components.Remove any soiling and salt andsugar splashes immediately.

Pressing the knob generates a sparkon the ignitor. Do not press the knobwhile you are cleaning or touchingthe cooktop or a burner in the vicinityof an ignitor.

Unsuitable cleaning agentsTo avoid damaging the surfaces of theappliance, do not use:

- cleaning agents containing soda, al-kalines, ammonia, acids, or chlorides,

- cleaning agents containing lime scaleremover

- stain or rust removers

- abrasive cleaning agents, such asscouring powder, scouring liquid, orpumice stones

- cleaning agents containing solvents

- dishwasher cleaner

- grill and oven sprays

- glass cleaners

- hard, abrasive brushes or sponges(e.g., pot scourers), or sponges whichhave been previously used and stillcontain abrasive cleaning agents

- eraser sponges

Cleaning and care

31

The entire cooktop should be cleanedafter each use.

Soften any stubborn soiling before-hand.

Dry the cooktop after using water toclean it. This helps prevent lime de-posits.

Stainless-steel cooktop

Risk of damage caused bypointed objects.The seal between the cooktop andthe countertop could be damaged.Do not use pointed objects for clean-ing.

Damage due to soiling.Soiling, particularly salty food or liq-uid and olive oil, can cause damageif left on the printed surfaces for along time.Remove such soiling immediately.

Damage due to incorrect clean-ing.Stainless-steel cleaners rub off theprinted symbols.Do not use stainless-steel cleanerson printed symbols.

Clean the stainless-steel cooktopwith a soft sponge, warm water, anda small amount of liquid dish soap.Soften any stubborn soiling before-hand. If necessary, the rough side ofa kitchen sponge can be used.

Finally, dry with a clean soft cloth.

Grates Remove the grates.

Clean the grates in a dishwasher orwith a solution of warm water and alittle liquid dish soap applied with asoft sponge. Soften any stubbornsoiling beforehand.

Dry the the grates thoroughly with aclean cloth.

Control knobs

The control knobs are not dish-washer safe.The control knobs should only becleaned by hand.

The control knobs may become dis-colored if they are not cleaned regu-larly.Clean the control knobs after eachuse.

Clean the knobs with a soft sponge,warm water, and a small amount ofliquid dish soap.

Cleaning and care

32

Burner

Cleaning the burners

Do not clean any parts of the burnerin a dishwasher.

The burner should be dismantled andthen cleaned only by hand using asolution of warm water and a smallamount of liquid dish soap appliedwith a soft sponge.

Clean any soiling from the flameopenings with the brush supplied.

Risk of explosion.Blocked flame openings can cause adangerous build-up of gas in thebase of the cooktop, which could ig-nite and cause an explosion. Thiscan lead to damage to the applianceand injury.Ensure the flame openings are keptclean at all times.

Parts of the burner that cannot be re-moved should be wiped clean with adamp cloth only.

The ignitor and ignition safety deviceshould be very carefully wiped cleanusing a well wrung-out cloth.

Do not let the ignitor get wet. If it getswet, it will not spark.

Finally dry everything thoroughly witha clean cloth. Make sure that theflame openings are completely dry.

The surface of the burner cap will be-come more matte with time. This isquite normal and does not indicatedamage to the material.

Cleaning and care

33

Assembling the wok burner

Place the burner head onto theburner base so that the thermo-couple and the ignition elec-trode extend through their respec-tive holes in the burner head. The lobe on the burner cap mustfit into the recess on the burnerhead. The lobe on the burner headmust fit into the recess on theburner base.

Replace the burner ring .

Then place the burner caps and in position.

Burners cannot function cor-rectly if they are incorrectly assem-bled. This can lead to damage to theappliance and injury.Ensure that all parts of the burner arereassembled in the correct order.

Cleaning and care

34

Assembling the normal and powerburners

a

b

Place the burner cap on the burnerbase so that the lobes on the burnercap engage in the holes in the burnerbase.

Burners cannot function cor-rectly if they are incorrectly assem-bled. This can lead to damage to theappliance and injury.Ensure that all parts of the burner arereassembled in the correct order.

Checking burning properties

Ignite all burners to check that theyare operating correctly:

- The flame must not go out on thelowest setting, or when the knob isturned quickly from the highest to thelowest setting.

- On the highest setting, the flamemust have a distinctive and visiblecore.

Frequently Asked Questions

35

With the help of the following guide minor faults in the performance of the ma-chine, some of which may result from incorrect operation, can be remedied with-out contacting the Service Department.

This guide may help you to find the reason for the fault, and how to correct it.

Problem Possible cause and solution

The burners do not ig-nite when the cooktopis being used for thefirst time or after it hasbeen out of use for alonger period.

There may be air in the gas line. Try to light the burner again, making several at-

tempts if necessary.

The burner does notlight after several at-tempts.

There is a technical fault. Turn all of the control knobs clockwise to the po-

sition and interrupt the power supply to the cook-top for a few seconds.

The burner is not properly assembled. Assemble the burner correctly.

The gas shut-off valve is closed. Open the gas shut-off valve.

The burner is wet and/or dirty. Clean and dry the burner.

The flame holes are clogged and/or wet. Clean and dry the flame holes.

The gas flame goes outafter being lit.

The flames do not touch the ignition safety deviceand the burner does not get hot enough:The burner parts are not positioned correctly. Assemble the burner components correctly.

The thermocouple is dirty. Remove any dirt or grime.

The shape/color of thegas flame changes.

The burner parts are not in the proper position. Position the burner parts correctly.

The burner cap itself or the holes in the burner capare dirty. Remove any dirt or grime.

The gas flame goes outduring use.

The burner parts are not in the proper position. Assemble the burner components correctly.

Frequently Asked Questions

36

Problem Possible cause and solution

The ignitor does notfunction properly.

The circuit breaker in the building’s wiring systemwas tripped. If necessary, contact a qualified service technician

or Technical Service for assistance.

There is food residue stuck between the ignitor andthe burner cap.The thermocouple is dirty. Remove any soiling (See “Cleaning and care”).

Optional accessories

37

Miele offers a range of useful acces-sories, as well as cleaning and condi-tioning products for your appliance.

These products can be easily orderedfrom the Miele webshop.

These products can also be orderedfrom Miele Technical Service (see theend of these operating instructions) oryour Miele dealer.

Stainless steel conditioner250 ml

Removes heavy soiling, lime scale, andaluminum residue.

Customer Service

38

Contact in the event of a faultIn the event of a fault which you cannot remedy yourself, please contact yourMiele dealer or Miele Customer Service.

You can book a Miele Service Call online at www.miele.com/service.

Contact information for Miele Customer Service can be found at the end of thisdocument.

Please quote the model identifier and serial number of your appliance (SN) whencontacting Miele Customer Service. Both pieces of information can be found onthe data plate.

Appliance warranty and product registrationYou can register your product and/or view the manufacturer´s warranty terms andconditions for Miele appliances and vacuum cleaners at www.mieleusa.com.

Installation

*INSTALLATION*

39

IMPORTANT SAFETY INSTRUCTIONS - INSTALLATION

Risk of damage caused by incorrect installation.Incorrect installation can damage the cooktop.The cooktop must only be installed by a qualified specialist.

Damage from falling objects.Take care not to damage the cooktop when installing cabinetry or a ventilationhood above it.Install the cabinetry and ventilation hood before installing the cooktop.

The room in which the cooktop is installed must conform to all rel-evant local and national building regulations and safety regulations.

The countertop must be heat-resistant (up to 212°F / 100°C), sothat it does not become deformed or the veneer detached. The wallstrips must be heat-resistant as well.

The cooktop must not be installed above refrigerators/freezers,dishwashers, or washer/dryers.

A gas cooktop must not be installed directly next to a deep fatfryer as the gas flames could ignite the fat in the fryer. It is essentialto maintain a distance of at least 12" (300 mm) between these twoappliances.

The maximum depth of cabinets installed above the cooktop mustbe no more than 13" (330 mm) or a greater depth specified by themanufacturers as tested by the certification agency.

When installing the cooktop, make sure that the gas pipe andpower cord cannot come into contact with hot appliance parts.

The power cord and any flexible gas connection pipes must be in-stalled in such a way so that they do not come into contact with anymoving kitchen parts (e.g. a drawer), and cannot become trapped.

Observe carefully the safety clearances listed on the followingpages.

Installation

*INSTALLATION*

40

Safety distances

No. Dimensions Description

13" (330 mm) Maximum depth of upper cabinet

2 3/4" (70 mm) Minimum distance to back wall

18" (457 mm) Minimum safety distance to bottomedge of adjacent cabinet

≥ cooktop width See “Installation – Installation dimensions”

30" (762 mm)1 Minimum safety distance between thetop of the cooktop surface and the bot-tom of an unprotected combustiblesurface.

12" (305 mm) Minimum distance to a side wall

1 The minimum safety distance given by the hood manufacturer must be maintained be-tween the cooktop and the hood above it. See the installation instructions supplied with thehood for these safety measurements. If there is more than one appliance beneath a hood (e.g., gas cooktop and electric cooktop)and they have different minimum safety distances, always observe the greater distance.

Installation

*INSTALLATION*

41

Installation notes

Seal between cooktop and counter-top

Damage caused by incorrect in-stallation.Using sealant under the cooktopcould result in damage to the cook-top and the countertop if the cook-top ever needs to be removed forservicing.Do not use sealant between thecooktop and the countertop.The sealing strip under the edge ofthe cooktop provides a sufficient sealfor the countertop.

Tiled countertop

Grout lines and the shaded area un-der the cooktop frame must be smoothand even. If they are not, the cooktopwill not sit flush with the countertop andthe sealing strip underneath the cook-top will not provide a good seal be-tween the cooktop and the countertop.

Installation

*INSTALLATION*

42

Installation dimensions

All dimensions in this instruction booklet are given in mm and inches.

KM 3464, KM 3465

(762 mm)

(720 mm)

( 635mm)

0

30(542 mm)

215/16"

20 3/8"

R4mm)

ß(

3/16"

ß

a

a

d

b

0( 70mm)

20 3/4"

020mm)

(

0 13/16"

25"

(518 mm)+-1 +-1

+-1+-1

(mm)

69

(190mm)

(58mm)

(83mm)

(78mm)

9mm3/8"

31/16"7

1/2"

211/16"

31/4"(215mm)

8 7/16"

283/8"

c

1 7/8"0( 7mm)4

2 5/16"

00

1/16"+-+-1/16"

+- 1/16"

+-1/16"

a Front

b Installation height

c Gas connection R ¹/₂" NPT

d Electrical supply connection box with power cord, L = 4' (1,200 mm)

Installation

*INSTALLATION*

43

KM 3474, KM 3475

(58mm)

2

36

ß3/16"

(889 mm)

(542 mm)

(914 mm)

+-

1

(9mm)3/8"

5/16"

ß( R4mm)

0( 47mm)

17/8"

+-

1

+-

1

35

b

a

0( 70mm)

20 3/4"

3/8"20(518 mm)

+-

1

21 5/16"

( 635mm)

0 25"

013/16"

020mm) c

(170mm)

(142mm)

(226mm)

d(86mm)3/8"3

87/8"

6 11/16"

59/16"

(78mm)31/16"

(185mm)

7 5/16"

b

a

1/16"+-

+-

1/16"

+-

1/16"

+-

1/16"

0

(80mm)31/8"

a Front




Installation

*INSTALLATION*

44

KM 3484, KM 3485

ß3/16"

215/16"(542 mm)

(1079 mm) (9mm)3/8"

421/2"

b

+-

1

( R4mm)

ß

0( 635mm)

0( 20mm)13/16"

0

(87mm) (307,5mm)

(228mm)

+-1

(1054 mm)

411/2"

+-

1

270mm

0

3/8"20+-

1

0( 47mm)

1

(518 mm)a

9"

121/8"

37/16"

(83mm)

3/4"

a

(220mm)

811/16"

d

c

b

(86mm)3/8"3

0

+-

1/16"1/16"+-

+-

1/16"

+-

1/16"0

25"0

31/4"

(58mm)

25/16"

7/8"

(78mm)31/16"

a Front




Installation

*INSTALLATION*

45

Installation

Preparing the countertop

Create the countertop cut-out asshown in the cooktop diagram. Re-member to maintain the minimumsafety distances (see “Installation – Safety distances”).

Seal any cut surfaces on the woodencountertop with a special varnish, sili-cone rubber, or resin to prevent thewood from swelling as a result ofmoisture. The sealant must be tem-perature-resistant.

Ensure that the sealant does not geton the top surface of the countertop.

The sealing strip ensures that thecooktop will sit securely in the cut-outwithout slipping. Any gap between thetrim and countertop will becomesmaller over time.

Installing the cooktop

Feed the appliance power cord downthrough the counter cut-out.

Place the cooktop centrally in thecut-out. When doing this make surethat the seal of the appliance sitsflush with the countertop on all sides.This is important to ensure an effec-tive seal all round.

If during installation the seal aroundthe frame does not sit flush with thecountertop in the corners, the cornerradius, maximum 3/16" (≤ R4/ 4 mm),can be carefully filed down to fit.

Do not use any additional sealant(e.g. silicone).

Connect the cooktop to the electricalpower supply (see “Installation – Electrical connection”).

Connect the cooktop to the gas sup-ply (see “Installation – Gas connec-tion”).

Installation

*INSTALLATION*

46

Securing the cooktop

The brackets are suitable for securingthe cooktop in a flush-fit or proud in-stallation. The illustrations show thecooktop secured in a proud installa-tion.

Secure the cooktop using the brack-ets supplied.

Checking for proper function

After installing the cooktop, ignite allburners to check that they are operat-ing correctly:

- The flame must not go out on thelowest setting, or when the control isturned quickly from the highest to thelowest setting.

- On the highest setting, the flamemust have a distinctive and visiblecore.

Installation

*INSTALLATION*

47

Gas connection

Connection to the gas supplymay only be performed by a duly au-thorized technician. This technician isresponsible for proper function at theinstallation site.In Massachusetts, the gas connec-tion may be performed only by a cer-tified gas installer.

The appliance must be connectedwith its own shut-off valve.The shut-off valve must be accessi-ble and visible, after the opening of acabinet door, if necessary.

The gas connection can be to naturalgas or propane gas according to themodel.Ask your gas company what kind ofgas is used and compare it with thespecifications on the data plate.

The appliance is not connected to anexhaust vent.During the setup and connection ofthe appliance, observe the applica-ble installation conditions, especiallysuitable ventilation measures.

Arrange the gas connections in sucha way that they are not heated anddamaged by the operation of the ap-pliance.In particular, make sure that the gashose lines and connection fittings onthe applinace do not come into con-tact with hot exhaust gases

The gas hose and power cord couldbe damaged by hot spots on the ap-pliance.Make sure that the gas hose andpower cord do not come into contactwith hot spots on the appliance.

Flexible connection lines can bedamaged by incorrect routing.Attach flexible connecting lines insuch a way so that they do not comeinto contact with any moving kitchenparts (e.g., a drawer) and are not ex-posed to mechanical stress.

Disconnect the appliance and theshut-off valve from the gas supplybefore performing a gas pressuretest at a pressure of more than ½ psi(3.5 kPA). Close the shut-off valve ofthe gas supply before performing agas pressure test at a pressure ofless than or equal to ½ psi (3.5 kPA).

Incorrectly sealed gas lines can leadto a gas leak and thus to an explo-sion.Seal all gas lines with a suitablethread sealant.

Seal tightness tests on the appliancemust be performed according tomanufacturer specifications.

Installation

*INSTALLATION*

48

The gas connection must be made inaccordance with local codes or, inthe absence of local codes, with:National Fuel Gas CodeANSI Z 223.1 / NFPA No. 54 for theUnited States or the current NaturalGas and Propane Installation Code,CSA B149.l. for Canada.

The gas pressure may not under-shoot or exceed certain values.Make sure that the maximum gaspressure upstream of the gas pres-sure controller does not amount tomore than ½ psi (3.5 kPA) for naturaland propane gas.Make sure that the minimum gassupply pressure amounts to 6" w.c.for natural gas and 1" w.c. forpropane gas.

The gas connection of the appliance isdesigned for natural gas or propane gasaccording to the ordered model.

If the appliance is not equipped with thecorrect connection for the gas type inyour household, contact your Mieledealer.

Installation

*INSTALLATION*

49

Gas pressure regulator

The cooktop is supplied together with agas pressure regulator that can be con-verted from natural gas to liquidpropane or from liquid propane to natu-ral gas. The regulator is supplied config-ured for the type of gas to which thecooktop is designed to be connected.Check this prior to installation.

Pressure setting:Natural gas 4" w.c.Liquid propane 1'" w.c.

a Cooktop

b ½" NPT gas connection

c Regulator

The regulator must be installed asshown in the diagram when you con-nect the Miele Cooktop to your gasconnection. The regulator has beenadapted by Miele to meet all statutorysafety requirements. The regulator mustbe easily accessible after the cooktophas been installed.

A flexible steel hose approved by theAGA or CGA can be used between thegas connection and the regulator. Thisflexible hose enables the cooktop to belifted out of the cut-out for maintenanceor repair work. Check to make sure thatno drawers, doors, or similar come intocontact with this flexible hose.

Gas leak due to unsuitable regulator.Only use the regulator supplied byMiele.

If you are in any doubt, contact MieleCustomer Service.

Leakage test

After connecting the appliance checkall fittings for gas leaks e.g. withsoapy water.

Installation

*INSTALLATION*

50

Burner ratings

Nominal ratings for KM 3464, KM 3465

Burner Gas type kW BTU/hr

Normal burner Natural gasLiquid propane

2.62.6

9,0009,000

Power burner Natural gasLiquid propane

3.53.5

12,00012,000

Wok Natural gasLiquid propane

4.54.5

15,30015,300

Total Natural gasLiquid propane

13.213.2

45,30045,300




2.62.6

9,0009,000


3.53.5

12,00012,000

Wok Natural gasLiquid propane

4.54.5

15,30015,300


17.717.7

60,60060,600

Installation

*INSTALLATION*

51




2.62.6

9,0009,000


3.53.5

12,00012,000

Wok, left (small) Natural gasLiquid propane

4.54.5

15,30015,300

Wok, right (large) Natural gasLiquid propane

4.84.8

16,50016,500


21.521.5

73,80073,800

Installation

*INSTALLATION*

52

Electrical connection

ATTENTION:During installation, maintenance andrepair work, the appliance must bedisconnected from the electricitysupply. It is only completely isolatedfrom the electricity supply if the plugfuses have been fully unscrewed(where applicable), the main circuitbreaker has been tripped or thepower cable has been unpluggedfrom the wall outlet.Do not cut off the plug on the powercord. If the plug does not fit in theoutlet, have an electrician install anappropriate outlet.The socket must be easily accessibleafter the appliance has been in-stalled.

Work by unqualified persons cancause considerable danger to users.Miele cannot be held liable for anydamage arising as a result of suchwork.Installation, repair and maintenancework should only be performed by aMiele authorized service technician.

To avoid damaging the appliance,the information (voltage and fre-quency) on the data plate must cor-respond to the building's power sup-ply.Compare these informations beforeconnecting the appliance. When indoubt, consult a qualified electrician.

The plug must be inserted into a suit-able outlet that has been installedand grounded in compliance with allapplicable local regulations.

To guarantee the electrical safety ofthis appliance, continuity must existbetween the appliance and an effec-tive grounding system. It is impera-tive that this basic safety require-ment be met. If there is any doubt,have the electrical system of thehouse checked by a qualified electri-cian.Installation, repair and maintenancework should only be performed by aMiele-authorized qualified electricianin compliance with local regulationsand the ANSI National ElectricalCode / NFPA 70 in the United Statesor the Canadian Electric Code, CSAC22.1-02. in Canada.

Installation

*INSTALLATION*

53

Power cord and plug

The appliance is equipped with a flexi-ble power cord and a 3-prong ground-ing plug for your protection againstshock hazard. The plug must be in-serted into a properly grounded outlet.

Do not cut or remove the groundingprong from this plug.

Total output

See data plate

Connection data

The connection data is given on thedata plate. Please ensure these matchthe household electrical supply.

Installer:

Please leave these instructions withthe customer.

MieleCare

54

This service is available in USA only.

MieleCare, our Extended Service Con-tract program, gives you the assuranceof knowing that your appliance invest-ment is covered by 5 years of worry freeownership.MieleCare is the only Extended ServiceContract in the industry that guaranteesrepairs by a Miele Authorized ServiceProvider using genuine Miele parts.Only genuine Miele parts installed byfactory trained professionals can guar-antee the safety, reliability, andlongevity of your Miele appliance.

Please note that unless expressly ap-proved in writing by Miele’s Service de-partment, Extended Service Contractsoffered by other providers for Mieleproducts will not be recognized byMiele. Our goal is to prevent unautho-rized (and untrained) service personnelfrom working on your Miele products,possibly doing further damage to them,you and/or your home.

To learn more about MieleCare Ex-tended Service Contracts, please con-tact your appliance dealer or visit usonline at:www.mieleusa.com

9 Independence WayPrinceton, NJ 08540

U.S.A.Miele, Inc.

National Headquarters

Please have the model and serial numberof your appliance available whencontacting Customer Service.

CanadaImporterMiele Limited

Headquarters and Miele Centre

Customer Service & SupportPhone: 888-99-MIELE(64353)[email protected]

161 Four Valley DriveVaughan, ON L4K 4V8www.miele.ca

Customer Care CentrePhone:

[email protected]

800-565-6435905-532-2272

International HeadquartersMiele & Cie. KGCarl-Miele-Straße 2933332 GüterslohGermany

M.-Nr. 06 818 490 / 09en-US, CA

KM 3464, KM 3465, KM 3474, KM 3475, KM 3484, KM 3485

Documents

Operating and Installation Instructions Gas cooktop