PANEL ANTENNASWITH TWO LOW BAND ARRAYS

22 | April 2015

TwinLine

April 2015 | 23

Quad antennas with two multiband arrays housed in an optimally designed package for low windload. Ideal for site/technology sharing.

Ordering Options Model Number

Manual Electrical Tilt 5980300

Remote Electrical Tilt AISG1.1 5980300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5980300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5980300DG

Access Ports Description (Connectors)

This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck

Ultra Wide Band Bottom System 1695-2690 MHz Ports (4x) 7/16-DIN Female Long Neck

Ultra Wide Band Top System 1695-2690 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics R1-R2 Y1-Y3 (Bottom) Y2-Y4 (Top)

Frequency Bands (MHz) 700 800 900 1800 2100 2600 1800 2100 2600

Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value

15.515.515.2

16.516.416.2

17.417.317.0

17.117.117.1

17.517.517.4

18.018.017.8

17.117.117.1

17.517.517.4

18.018.017.8

Input Impedance 50Ω 50Ω 50Ω

VSWR < 1.5 < 1.5 < 1.5

Polarisation ±45° ±45° ±45°

Horizontal Beamwidth (-3 dB) 75° 68° 65° 65° 63° 61° 65° 63° 61°

Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7° 7.0° 6.4° 5.2° 6.5° 5.9° 4.7°

Electrical Downtilt Range 0-10° 0-12° 0-12°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical 18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

> 30 dB> 25 dB

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W 200 W 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

(2x) 698-960 / 1695-2690 / 1695-2690 MHz

59803005980300A 5980300G 5980300DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt

• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• Lightweight TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD

R1 R2

Y2 Y4

Y1 Y3

24 | April 2015

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

59803005980300A 5980300G 5980300DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt

(2x) 698-960 / 1695-2690 / 1695-2690 MHz

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 48 kg

Shroud Outdoor Fibreglass, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

Location of the MDCU or MDDUfor RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 698-960 MHz

YELLOW 1695-2690 MHz

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 59 kg Includes 0900181/00 Kit

April 2015 | 25

(2x) 790-960 / 1710-2170 / 2500-2690 MHz

59822005982200A 5982200G

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt

• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°

• MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

Ordering Options Model Number

Manual Electrical Tilt 5982200

Remote Electrical Tilt AISG1.1 5982200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5982200G

Access Ports Description (Connectors)

This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.

RED and GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck

YELLOW Rings High Band (Top Array) 2500-2690 MHz Ports (4x) 7/16-DIN Female Long Neck

BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED or GREEN) High Band (BLUE) High Band (YELLOW)

Frequency Bands (MHz) 790...880...960 1710...1880 1900...2170 2500...2690

Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value

16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4

16.5...16.916.4...16.716.3...16.5

16.9...17.316.7...17.216.5...17.0

17.4...17.817.3...17.717.2...17.5

Input Impedance 50Ω 50Ω 50Ω

VSWR < 1.5 < 1.5 < 1.5

Polarisation ±45° ±45° ±45°

Horizontal Beamwidth (-3 dB) 75°...68°...63° 65° 62° 60°

Vertical Beamwidth (-3 dB) 7° 7° 5°

Electrical Downtilt Range 0-10° 0-12° 0-12°

Intra Band Isolation > 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical

Isolation Between Left & Right Arrays > 30 dB > 30 dB > 30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical 18 dB Typical

Front-to-Back Ratio > 30 dB > 30 dB > 30 dB

Maximum Power (Per Port) 200 W 160 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5982200A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5982200G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

LTE 800 ReadyLTE 2600 Ready

26 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2700 x 442 x 152 mm (219 mm with Rear Connectors)

Weight (Excluding Mounting Accessories) 56 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 160 km/h Frontal: 1300 N Lateral: 220 N Rear: 1700 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets Not available ---

(2x) 790-960 / 1710-2170 / 2500-2690 MHz

59822005982200A 5982200G

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 | 70 kg

RED 790-960 MHz

GREEN 790-960 MHz

BLUE 1710-2170 MHz

YELLOW 2500-2690 MHz

April 2015 | 27

(2x) 790-960 / 1710-2170 / 2500-2690 MHz

5982200 lv (lightweight version)5982200A lv 5982200G lv 5982200DG lv

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt

• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• Lightweight TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

Ordering Options Model Number

Manual Electrical Tilt 5982200 lv

Remote Electrical Tilt AISG1.1 5982200A lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5982200G lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22) 5982200DG lv

Access Ports Description (Connectors)

This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.

RED and GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck

YELLOW Rings High Band (Top Array) 2500-2690 MHz Ports (4x) 7/16-DIN Female Long Neck

BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED or GREEN) High Band (BLUE) High Band (YELLOW)

Frequency Bands (MHz) 790...880...960 1710...1880 1900...2170 2500...2690

Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value

16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4

16.5...16.916.4...16.716.3...16.5

16.9...17.316.7...17.216.5...17.0

17.2...17.617.1...17.517.0...17.3

Input Impedance 50Ω 50Ω 50Ω

VSWR < 1.5 < 1.5 < 1.5

Polarisation ±45° ±45° ±45°

Horizontal Beamwidth (-3 dB) 75°...68°...63° 65° 62° 60°

Vertical Beamwidth (-3 dB) 7° 7° 5°

Electrical Downtilt Range 0-10° 0-12° 0-12°

Intra Band Isolation > 28 dB> 27 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical

Isolation Between Left & Right Arrays > 28 dB (900 Band)> 27 dB (800 Band) > 30 dB > 30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical 18 dB Typical

Front-to-Back Ratio > 25 dB > 25 dB > 30 dB

Maximum Power (Per Port) 200 W 160 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

OPTIMAL PROFILE - LOW WINDLOAD

28 | April 2015

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 48 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load(EN1991-4-1)

at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N Highest value: 1450 N at 110°

at 160 km/h Frontal: 1130 N Lateral: 630 N Rear: 1045 N Highest value: 1650 N at 110°

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

(2x) 790-960 / 1710-2170 / 2500-2690 MHz

5982200 lv (lightweight version)5982200A lv 5982200G lv 5982200DG lv

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

2683

432

153

1865

Location of the MDCU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 790-960 MHz

GREEN 790-960 MHz

BLUE 1710-2170 MHz

YELLOW 2500-2690 MHz

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 59 kg Includes 0900181/00 Kit

April 2015 | 29

(2x) 790-960 / 1710-2170 / 1710-2170 MHz

59802005980200A 5980200G 5980200DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt

• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°

• MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

Ordering Options Model Number

Manual Electrical Tilt 5980200

Remote Electrical Tilt AISG1.1 5980200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5980200G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22) 5980200DG

Access Ports Description (Connectors)

This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.

RED and GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck

WHITE Rings High Band (Top Array) 1710-2170 MHz Ports (Wide Band) (4x) 7/16-DIN Female Long Neck

BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports(Wide Band Optimised for UMTS) (4x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE) High Band (BLUE)

Frequency Bands (MHz) 790...880 880...960 1710...1880 1900...2170 1710...1880 1900...2170

Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value

17.2 17.5 16.5...16.716.3...16.516.0...16.3

16.7...17.216.5...17.016.3...16.5

16.5...16.916.4...16.716.3...16.5

16.9...17.316.7...17.216.5...17.0

Input Impedance 50Ω 50Ω 50Ω

VSWR < 1.5 < 1.4 < 1.4

Polarisation ±45° ±45° ±45°

Horizontal Beamwidth (-3 dB) 75° 68° 65° 62° 65° 62°

Vertical Beamwidth (-3 dB) 7° 7° 7° 7° 7°

Electrical Downtilt Range 0-10° 0-12° 0-12°

Intra Band Isolation > 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical

Isolation Between Left & Right Arrays > 29 dB > 30 dB > 30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical 18 dB Typical

Front-to-Back Ratio > 30 dB > 30 dB > 30 dB

Maximum Power (Per Port) 200 W 160 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

LTE 800 Ready

30 | April 2015

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2700 x 442 x 152 mm (219 mm with Rear Connectors)

Weight (Excluding Mounting Accessories) 56 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 160 km/h (EN1991-4-1) Frontal: 1512 N Lateral: 512 N Rear: 1418 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

(2x) 790-960 / 1710-2170 / 1710-2170 MHz

59802005980200A 5980200G 5980200DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 | 70 kg

RED 790-960 MHz

GREEN 790-960 MHz

WHITE 1710-2170 MHz

BLUE 1710-2170 MHz

April 2015 | 31

(2x) 790-960 / 1710-2170 / 1710-2170 MHz

5980200 lv (lightweight version)5980200A lv 5980200G lv 5980200DG lv

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt

• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• Lightweight TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

Ordering Options Model Number

Manual Electrical Tilt 5980200 lv

Remote Electrical Tilt AISG1.1 5980200A lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5980200G lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22) 5980200DG lv

Access Ports Description (Connectors)

This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.

RED and GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck

WHITE Rings High Band (Top Array) 1710-2170 MHz Ports (Wide Band) (4x) 7/16-DIN Female Long Neck

BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports(Wide Band Optimised for UMTS) (4x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE) High Band (BLUE)

Frequency Bands (MHz) 790...880 880...960 1710...1880 1900...2170 1710...1880 1900...2170

Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value

17.2 17.5 16.5...16.716.3...16.516.0...16.3

16.7...17.216.5...17.016.3...16.5

16.5...16.916.4...16.716.3...16.5

16.9...17.316.7...17.216.5...17.0

Input Impedance 50Ω 50Ω 50Ω

VSWR < 1.5 < 1.4 < 1.4

Polarisation ±45° ±45° ±45°

Horizontal Beamwidth (-3 dB) 75° 68° 65° 62° 65° 62°

Vertical Beamwidth (-3 dB) 7° 7° 7° 7° 7°

Electrical Downtilt Range 0-10° 0-12° 0-12°

Intra Band Isolation > 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical

Isolation Between Left & Right Arrays > 29 dB > 30 dB > 30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical 18 dB Typical

Front-to-Back Ratio > 30 dB > 30 dB > 30 dB

Maximum Power (Per Port) 200 W 160 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

OPTIMAL PROFILE - LOW WINDLOAD

32 | April 2015

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 48 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load(EN1991-4-1)

at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N Highest value: 1450 N at 110°

at 160 km/h Frontal: 1130 N Lateral: 630 N Rear: 1045 N Highest value: 1650 N at 110°

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

(2x) 790-960 / 1710-2170 / 1710-2170 MHz

5980200 lv (lightweight version)5980200A lv 5980200G lv 5980200DG lv

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

2683

432

153

1865

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 790-960 MHz

GREEN 790-960 MHz

WHITE 1710-2170 MHz

BLUE 1710-2170 MHz

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 59 kg Includes 0900181/00 Kit

April 2015 | 33

(2x) 698-960 / 1695-2690 MHz

59613005961300A 5961300G 5961300DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt

• Twin dual band antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOADOrdering Options Model Number

Manual Electrical Tilt 5961300

Remote Electrical Tilt AISG1.1 5961300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5961300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5961300DG

Access Ports Description (Connectors)

This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck

Ultra Wide Band 1695-2690 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics R1-R2 Y1-Y2

Frequency Bands (MHz) 700 800 900 1800 2100 2600

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

15.515.515.2

16.516.416.2

17.417.317.0

17.717.717.7

18.118.118.0

18.518.518.2

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 75° 68° 65° 65° 63° 61°

Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7° 6.1° 5.3° 4.2°

Electrical Downtilt Range 0-10° 0-10°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

R1 R2

Y1 Y2

34 | April 2015

(2x) 698-960 / 1695-2690 MHz

59613005961300A 5961300G 5961300DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 44 kg

Shroud Outdoor Fibreglass, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 55 kg Includes 0900181/00 Kit

RED 698-960 MHz

YELLOW 1695-2690 MHz

April 2015 | 35

(2x) 790-960 / 1710-2170 MHz

59612005961200A 5961200G 5961200DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt

• Twin dual band Antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10°

• MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

Ordering Options Model Number

Manual Electrical Tilt 5961200

Remote Electrical Tilt AISG1.1 5961200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5961200G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12) 5961200DG

Access Ports Description (Connectors)

This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.

RED | GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck

WHITE | BLUE Rings High Band 1710-2170 MHz Ports (Wide Band) (4x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE or BLUE)

Frequency Bands (MHz) 790...880...960 MHz 1710...1880 1900...2170

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4

17.8...18.217.7...18.017.6...17.8

18.2...18.618.0...18.517.8...18.3

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 75°...68°...63° 65° 62°

Vertical Beamwidth (-3 dB) 7.0° 5.5° 5.0°

Electrical Downtilt Range 0-10° 0-10°

Intra Band Isolation > 28 dB > 30 dB, > 28 dB from 0° to 2° tilt

Isolation Between Bands 45 dB Typical 45 dB Typical

Isolation Between Left & Right Arrays > 25 dB for 790-880 MHz> 28 dB for 880-960 MHz > 30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio > 30 dB > 30 dB

Maximum Power (Per Port) 200 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

LTE 800 Ready

36 | April 2015

(2x) 790-960 / 1710-2170 MHz

59612005961200A 5961200G 5961200DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2700 x 442 x 152 mm

Weight (Excluding Mounting Accessories) 52 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 160 km/h (EN1991-4-1) Frontal: 1512 N Lateral: 512 N Rear: 1418 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 | 67 kg

RED 790-960 MHz

GREEN 790-960 MHz

BLUE 1710-2170 MHz

WHITE 1710-2170 MHz

April 2015 | 37

(2x) 790-960 / 1710-2170 MHz

5961200 lv (lightweight version)5961200A lv 5961200G lv 5961200DG lv

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt

• Twin dual band antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10°• Lightweight TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

Ordering Options Model Number

Manual Electrical Tilt 5961200 lv

Remote Electrical Tilt AISG1.1 5961200A lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5961200G lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12) 5961200DG lv

Access Ports Description (Connectors)

This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.

RED | GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck

WHITE | BLUE Rings High Band 1710-2170 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE or BLUE)

Frequency Bands (MHz) 790...880...960 MHz 1710...1880 1900...2170

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4

17.8...18.217.7...18.017.6...17.8

18.2...18.618.0...18.517.8...18.3

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 75°...68°...63° 65° 62°

Vertical Beamwidth (-3 dB) 7.0° 5.5° 5.0°

Electrical Downtilt Range 0-10° 0-10°

Intra Band Isolation > 28 dB > 30 dB, > 28 dB from 0° to 2° tilt

Isolation Between Bands 45 dB Typical 45 dB Typical

Isolation Between Left & Right Arrays > 25 dB for 790-880 MHz> 28 dB for 880-960 MHz > 30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio > 30 dB > 30 dB

Maximum Power (Per Port) 200 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

LTE 800 Ready

38 | April 2015

(2x) 790-960 / 1710-2170 MHz

5961200 lv (lightweight version)5961200A lv 5961200G lv 5961200DG lv

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

2683

432

153

1865

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 44 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load(EN1991-4-1)

at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N Highest value: 1450 N at 110°

at 160 km/h Frontal: 1130 N Lateral: 630 N Rear: 1045 N Highest value: 1650 N at 110°

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 | 59 kg

RED 790-960 MHz

GREEN 790-960 MHz

BLUE 1710-2170 MHz

WHITE 1710-2170 MHz

April 2015 | 39

(2x) 698-960 MHz

59203005920300A 5920300G 5920300DG

Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt

• Twin low band, dual polarisation, 4 connectors • Independent tilt on each band 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5920300

Remote Electrical Tilt AISG1.1 5920300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5920300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5920300DG

Access Ports Description (Connectors)

This antenna is built with two identical Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics R1-R2

Frequency Bands (MHz) 700 800 900

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

15.515.515.2

16.516.416.2

17.417.317.0

Input Impedance 50Ω

VSWR < 1.5

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 75° 68° 65°

Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7°

Electrical Downtilt Range 0-10°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

R1 R2

OPTIMAL PROFILE - LOW WINDLOAD

40 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2863 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 35 kg

Shroud Outdoor Fibreglass, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

(2x) 698-960 MHz

59203005920300A 5920300G 5920300DG

Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 66 kg Includes 0900181/00 Kit

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 698-960 MHz

April 2015 | 41

(2x) 790-960 MHz

59202005920200A 5920200G

Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt

• Twin 900 MHz antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10°

• MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control both tilt angles, fully inserted inside the antenna (field replaceable)

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5920200

Remote Electrical Tilt AISG1.1 5920200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5920200G

Access Ports Description (Connectors)

This antenna is built with two identical 900 MHz Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.

RED Rings Ultra Low Band Right 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck

GREEN Rings Ultra Low Band Left 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck

Electrical Characteristics RED or GREEN Ports

Frequency Bands (MHz) 790...880...960 MHz

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4

Input Impedance 50Ω

VSWR < 1.4

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 65° (±6°)

Vertical Beamwidth (-3 dB) 7.3°

Electrical Downtilt Range 0-10°

Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt

Isolation Between Left & Right Arrays > 30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical

Null Fill (First Null Below Main Beam) < 20 dB

Front-to-Back Ratio > 30 dB

Maximum Power (Per Port) 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5920200A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5920200G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

LTE Ready

42 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2700 x 442 x 152 mm

Weight (Excluding Mounting Accessories) 45 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 160 km/h Frontal: 1300 N Lateral: 220 N Rear: 1700 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets Not available ---

(2x) 790-960 MHz

59202005920200A 5920200G

Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 790-960 MHz

GREEN 790-960 MHz

April 2015 | 43

(2x) 790-960 MHz

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5920200 lv

Remote Electrical Tilt AISG1.1 5920200A lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5920200G lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22) 5920200DG lv

Access Ports Description (Connectors)

This antenna is built with two identical Extended Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.

RED Rings Extended Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck

GREEN Rings Extended Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED or GREEN Ports)

Frequency Bands (MHz) 790...880...960 MHz

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4

Input Impedance 50Ω

VSWR < 1.5

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 73°...68°...63°

Vertical Beamwidth (-3 dB) 7.3°

Electrical Downtilt Range 0-10°

Inter/Intra Band Isolation > 28 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical

Front-to-Back Ratio > 30 dB

Maximum Power (Per Port) 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

LTE Ready

EXTREMELY PROFILED - LOW WINDLOAD

• Twin 800-900 antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10°• Lightweight TwinLine platform • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

5920200 lv (lightweight version)5920200A lv 5920200G lv 5920200DG lv

Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt

44 | April 2015

(2x) 790-960 MHz

5920200 lv (lightweight version)5920200A lv 5920200G lv 5920200DG lv

Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

153

432

1865 1983

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 37 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h (EN1991-4-1) Frontal: 990 N Lateral: 555 N Rear: 920 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

Packaging

Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 51 kg Includes 0900181/00 Kit

RED 790-960 MHz

GREEN 790-960 MHz

April 2015 | 45

(2x) 698-960 / 1695-2180 / 2490-2690 MHz

59786005978600A 5978600G 5978600DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 16.5 / 17.5 / 18.0 dBi | Variable Tilt

• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-10° / 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOADOrdering Options Model Number

Manual Electrical Tilt 5978600

Remote Electrical Tilt AISG1.1 5978600A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5978600G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5978600DG

Access Ports Description (Connectors)

This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck

Wide Band 1695-2180 MHz Ports (4x) 7/16-DIN Female Long Neck

LTE 2600 2490-2690 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics R1-R2 B1-B2 Y1-Y2

Frequency Bands (MHz) 700 800 900 1800 2100 2600

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

14.514.514.2

15.515.415.1

16.416.316.0

17.417.417.4

17.717.717.6

18.018.017.7

Input Impedance 50Ω 50Ω 50Ω

VSWR < 1.5 < 1.5 < 1.5

Polarisation ±45° ±45° ±45°

Horizontal Beamwidth (-3 dB) 75° 68° 65° 65° 63° 61°

Vertical Beamwidth (-3 dB) 12° 10° 9.4° 6.1° 5.3° 4.2°

Electrical Downtilt Range 0-10° 0-10° 0-10°

Inter/Intra Band Isolation > 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

> 30 dB> 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical 18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

> 30 dB> 25 dB

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W 200 W 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

R1 R2

Y1 Y2

B1 B2

46 | April 2015

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Mechanical Characteristics

Dimensions (Height x Width x Depth) 1915 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 40 kg

Shroud Outdoor Fibreglass, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 635 N Lateral: 395 N Rear: 656 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

(2x) 698-960 / 1695-2180 / 2490-2690 MHz

59786005978600A 5978600G 5978600DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 16.5 / 17.5 / 18.0 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Packaging

Carton Box 2.15 x 0.55 x 0.28 m 0.33 m3 50 kg Includes 0900181/00 Kit

RED 698-960 MHz

BLUE 1695-2180 MHz

YELLOW 2490-2690 MHz

April 2015 | 47

(2x) 698-960 / 1695-2690 MHz

59633005963300A 5963300G 5963300DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt

• Twin dual band antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOADOrdering Options Model Number

Manual Electrical Tilt 5963300

Remote Electrical Tilt AISG1.1 5963300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5963300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5963300DG

Access Ports Description (Connectors)

This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck

Ultra Wide Band 1695-2690 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics R1-R2 Y1-Y2

Frequency Bands (MHz) 700 800 900 1800 2100 2600

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

14.514.514.2

15.515.415.1

16.416.316.0

17.717.717.7

18.118.118.0

18.518.518.2

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 75° 68° 65° 65° 63° 61°

Vertical Beamwidth (-3 dB) 12° 10° 9.4° 6.1° 5.3° 4.2°

Electrical Downtilt Range 0-10° 0-10°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

R1 R2

Y1 Y2

48 | April 2015

(2x) 698-960 / 1695-2690 MHz

59633005963300A 5963300G 5963300DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Mechanical Characteristics

Dimensions (Height x Width x Depth) 1915 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 33 kg

Shroud Outdoor Fibreglass, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 635 N Lateral: 395 N Rear: 656 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

Packaging

Carton Box 2.15 x 0.55 x 0.28 m 0.33 m3 43 kg Includes 0900181/00 Kit

RED 698-960 MHz

YELLOW 1695-2690 MHz

April 2015 | 49

(2x) 790-960 / 1710-2170 MHz

59632005963200A 5963200G 5963200DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 68° / 68° | 16.5 / 18.1 dBi | Variable Tilt

• Twin dual band antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10° • TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies

Ordering Options Model Number

Manual Electrical Tilt 5963200

Remote Electrical Tilt AISG1.1 5963200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5963200G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12) 5963200DG

Access Ports Description (Connectors)

This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.

RED | GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck

WHITE | BLUE Rings High Band 1710-2170 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE or BLUE)

Frequency Bands (MHz) 790...880...960 MHz 1710...1880 1900...2170

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

15.5...16.0...16.515.5...16.0...16.515.4...15.9...16.4

17.3...17.617.2...17.417.2...17.3

17.6...18.117.4...17.917.3...17.7

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 72°...68°...65° 65° 64°

Vertical Beamwidth (-3 dB) 9° 6° 6°

Electrical Downtilt Range 0-10° 0-10°

Intra Band Isolation > 25 dB > 28 dB

Isolation Between Bands > 30 dB > 30 dB

Isolation Between Left & Right Arrays > 30 dB > 30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio > 30 dB > 30 dB

Maximum Power (Per Port) 200 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

50 | April 2015

(2x) 790-960 / 1710-2170 MHz

59632005963200A 5963200G 5963200DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 68° / 68° | 16.5 / 18.1 dBi | Variable Tilt

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

Mechanical Characteristics

Dimensions (Height x Width x Depth) 1920 x 442 x 152 mm

Weight (Excluding Mounting Accessories) 41.5 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load (EN1991-4-1)

at 150 km/h Frontal: 945 N Lateral: 320 N Rear: 886 N

at 160 km/h Frontal: 1075 N Lateral: 365 N Rear: 1008 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

Packaging

Carton Box 2.23 x 0.55 x 0.28 m 0.343 m3 | 52 kg

RED 790-960 MHz

GREEN 790-960 MHz

BLUE 1710-2170 MHz

WHITE 1710-2170 MHz

April 2015 | 51

(2x) 698-960 MHz

59183005918300A 5918300G 5918300DG

Twin Band | Panel Antenna | (2x) X-Pol | 65° | 16.5 dBi | Variable Tilt

• Twin low band, dual polarisation, 4 connectors • Independent tilt on each band 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5918300

Remote Electrical Tilt AISG1.1 5918300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5918300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5918300DG

Access Ports Description (Connectors)

This antenna is built with two identical Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck

Electrical Characteristics R1-R2

Frequency Bands (MHz) 700 800 900

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

14.514.514.2

15.515.415.1

16.416.316.0

Input Impedance 50Ω

VSWR < 1.5

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 75° 68° 65°

Vertical Beamwidth (-3 dB) 12° 10° 9.4°

Electrical Downtilt Range 0-10°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

R1 R2

OPTIMAL PROFILE - LOW WINDLOAD

52 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 1915 x 432 x 153 mm

Weight (Excluding Mounting Accessories) 24 kg

Shroud Outdoor Fibreglass, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 635 N Lateral: 395 N Rear: 656 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

(2x) 698-960 MHz

59183005918300A 5918300G 5918300DG

Twin Band | Panel Antenna | (2x) X-Pol | 65° | 16.5 dBi | Variable Tilt

Packaging

Carton Box 2.15 x 0.55 x 0.28 m 0.33 m3 34 kg Includes 0900181/00 Kit

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 698-960 MHz

April 2015 | 53