Petroleum Exploration and Extraction Technical Standards ... · Petroleum Exploration and Extraction Technical Standards Committee 6 ISO/TC 185, Safety devices for protection against

RECOMMENDED STANDARDS SELECTION POLICY 2015

Petroleum Exploration and Extraction Technical Standards Committee


2

Contents

Page

Foreword .......................................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Legislation ......................................................................................................................................................... 4

3 Terms and definitions ................................................................................................................................... 4 3.1 Abbreviations ................................................................................................................................................... 4 3.2 Standards Technical Committee titles ..................................................................................................... 5

4 Selection of suitable Standards .................................................................................................................. 6

5 Rigs and other equipment designed for International use .............................................................. 6

6 List of suitable Standards ............................................................................................................................. 6

7 Standards in the Oil and Gas industry ..................................................................................................... 7 7.1 Introduction ...................................................................................................................................................... 7 7.2 Explanation of Standard designations ..................................................................................................... 7 7.2.1 Standards ........................................................................................................................................................... 7 7.2.2 Technical Specifications ............................................................................................................................... 8 7.2.3 Technical Report ............................................................................................................................................. 8

8 List of Irish National Standards and International Standard for the Oilfield ............................ 9 8.1 Down hole ....................................................................................................................................................... 10 8.2 Subsea drilling and production equipment ........................................................................................ 13 8.3 Surface drilling, production and processing equipment and systems...................................... 14 8.4 Offshore structures (Semi submersibles) ........................................................................................... 16 8.5 Offshore structures (Platforms, jackets and jack-ups) ................................................................... 17 8.6 Pipeline transportation systems ............................................................................................................ 18 8.7 Onshore processing ..................................................................................................................................... 19

9 Information on each Technical Committee......................................................................................... 22 9.1 ISO/TC 67 - Structure .................................................................................................................................. 22 9.1.1 ISO/TC 67 ........................................................................................................................................................ 22 9.1.2 ISO/TC 67/SC 2 .............................................................................................................................................. 25 9.1.3 ISO/TC 67/SC 3 .............................................................................................................................................. 26 9.1.4 ISO/TC 67/SC 4 .............................................................................................................................................. 28 9.1.5 ISO/TC 67/SC 5 .............................................................................................................................................. 31 9.1.6 ISO/TC 67/SC 6 .............................................................................................................................................. 32 9.1.7 ISO/TC 67/SC 7 .............................................................................................................................................. 34 9.1.8 ISO/TC 67/SC 8 .............................................................................................................................................. 35 9.1.9 ISO/TC 67/SC 9 .............................................................................................................................................. 36 9.2 ISO/TC 60 ........................................................................................................................................................ 36 9.3 ISO/TC 115 ...................................................................................................................................................... 39 9.4 ISO/TC 118 ...................................................................................................................................................... 40 9.5 ISO/TC 153 ...................................................................................................................................................... 41 9.6 ISO/TC 192 - Gas turbines ......................................................................................................................... 43 9.7 CEN/TC 12 ....................................................................................................................................................... 45 9.8 CEN/TC 69 ....................................................................................................................................................... 55


3

Foreword

In response to a request from the Commission of Energy Regulation (CER) the NSAI/TC 50 Petroleum Exploration and Extraction Technical Standards Committee (PEETSC) has developed this recommended Standards selection policy document to be applied to petroleum exploration and extraction activities.

This policy recommendation may assist in fulfilling the CER's obligation to consult NSAI with regard to the following provisions of the Petroleum (Exploration and Extraction) Safety Act Number 26 of 2015, namely sections:

13 H (2) (a),

13 L (2) (a) (i),

13 L (3) (c) and

13 L (3) (d).

This document has been prepared for circulation on 12th January 2016


4

1 Scope

This recommendation sets out a policy that can be applied to petroleum undertakings when selecting suitable Standards to be applied for any petroleum activity licensed under the Act.

It recognises the extensive number of Standards available and the fact that many new and revised standards are published every year. It also recognises that, given the nature of the activity, there cannot be an exhaustive list of suitable standards.

This document provides a list of recommended standards that can be to applied petroleum exploration and extraction activities.

2 Legislation

Standards emanating from Standards bodies are not, in themselves, mandatory and only achieve a mandatory status when referenced in legal instruments.

In all cases legislation takes precedence over any voluntary Standard.

3 Terms and definitions

3.1 Abbreviations

ANSI, American National Standards Institute

API; American Petroleum Institute

CEN; European Committee for Standardization

CENELEC; European Committee for Electrotechnical Standardization

CER; Commission of Energy Regulation

ECISS; European Committee for Iron and Steel Standardization

EN; European Standard

ETCI; Electro Technical Counsil of Ireland

IEC; International Electrotechnical Commission

I.S.; Irish Standard

ISO; International Organization for Standardization

NSAI; National Standards Authority of Ireland

PAS; Publicly Available Specification

PEETSC; Petroleum Exploration and Extraction Technical Standards Committee

SC; Subcommittee

S.R.; Standard Recommendation


5

TC; Technical Committee

TR, Technical Report

TS, Technical Specification

3.2 Standards Technical Committee titles

The titles of the Technical Committees listed in this document.

CEN ECISS/TC 110, Steel tubes, and iron and steel fittings

CEN/TC 12, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries

CEN/TC 69, Industrial valves

CEN/TC 164/WG 8, Water supply - Sanitary tapware

CENELEC/TC 31, Electrical apparatus for potentially explosive atmospheres

IEC/TC 31, Equipment for explosive atmospheres

IEC/TC 65, Industrial-process measurement, control and automation

ISO/TC 8, Ships and marine technology

ISO/TC 20, Aircraft and space vehicles

ISO/TC 29, Small tools

ISO/TC 60/SC 2, Gears - Gear capacity calculation

ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries

ISO/TC 67/SC 2, Pipeline transportation systems

ISO/TC 67/SC 4, Drilling and production equipment

ISO/TC 67/SC 5, Casing, tubing and drill pipe

ISO/TC 67/SC 6, Processing equipment and systems

ISO/TC 67/SC 7, Offshore structures

ISO/TC 115/SC 3, Pumps - Installation and special application

ISO/TC 118/SC 1, Compressors and pneumatic tools, machines and equipment- Process compressors

ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids

ISO/TC 153, Valves


6

ISO/TC 185, Safety devices for protection against excessive pressure

ISO/TC 192, Gas turbines

4 Selection of suitable Standards

4.1 When selecting suitable Standards for petroleum exploration and extraction activities they should be selected in order of preference:

a) Irish Standards Specifications (I.S.);

b) NSAI adoptions of European (EN) and International Standards (ISO);

c) International Standards (ISO).

These publications specify minimum requirements for the relevant activity.

4.2 In the event that a particular activity, covered the Standard types listed in 3.1, is addressed more comprehensively in another publication, undertakings may apply that publication, provided that any requirements contained in the Standard types listed in 3.1 are also met.

In the event that a particular activity is not covered by the Standard types listed in 3.1, undertakings can choose to use publications such as the following:

a) Standards from other National Standards Bodies;

b) Other NSAI publications;

c) Standards from Classification Societies (e.g. Bureau Veritas);

d) Publications from suitable associations (e.g. API).

5 Rigs and other equipment designed for International use

The PEETSC recognises that the building of equipment such as oil rigs is a truly international activity. Most rigs are built to meet the expectations of operators active in other national and international waters. Given this, the selection of Standards used to construct/build such equipment cannot, necessarily follow this policy. However the PEETSC also recognises that such equipment is almost always built to classification society rules in order to operate to the satisfaction of authorities in other jurisdictions.

6 List of suitable Standards

The lists of Standards in Section 8 (correct on the date of compilation) are identified suitable Standards for petroleum exploration and extraction activities. It does not purport to be a comprehensive list but is a guide to the reader of the types of Standards NSAI has recognised as suitable. It is the intention that this list will be updated from time to time but no less than every two years.


7

7 Standards in the Oil and Gas industry

7.1 Introduction

The standards listed in this document are recommended as suitable for application in Ireland. This list is not exhaustive.

The majority of Standards referenced in this document have been developed and published by the International Standards Organisation, ISO, under the Technical Committee ISO/TC 67. Where these ISO Standards can be adopted by Europe directly without modification they are adopted and published by the European Committee for Standardisation (CEN) under Technical Committee CEN/TC 12. Where a modification is required to an ISO Standard CEN/TC 12 publishes the ISO Standard as a European Standard with its own number and develops the European Standard with the specific European requirements.

ISO Standards are not automatically adopted as Irish Standards.

European Standards are automatically adopted as Irish Standards.

Standards relating to Explosive atmospheres are managed by the national committee ETCI/TC 6 which mirrors the work of CENELEC/TC 31 and IEC/TC 31. CEN/TC 305 also develops EN standards specifically for explosive atmospheres.

7.2 Explanation of Standard designations

7.2.1 Standards

A Standard is a document that provides requirements, specifications, guidelines or characteristics that can be used consistently to ensure that materials, products, processes and services are fit for their purpose. Table 1.0 explains the different designations for Standards listed in this document.

Table 1.0 – Designations for Standards

Designation Explanation

I.S. 123 Irish Standard developed and published by NSAI

S.R. 123 Irish Standard Recommendation published by NSAI

EN 12345 European Standard published by CEN/CENELEC

ISO 12345 International Standard published by ISO

IEC 60125 International Standard published by IEC

I.S. EN 12345 European Standard adopted as an Irish Standard

EN ISO 12345 ISO Standard adopted as a European Standard

I.S. EN ISO 12345 European Standard adopted as an Irish Standard

I.S. ISO 12345 ISO Standard adopted as an Irish Standard

http://www.etci.ie/technical/tc6.html


8

7.2.2 Technical Specifications

A Technical Specification is a document for which there is the future possibility of agreement on a Standard, but for which at present:

the required support for approval as a Standard cannot be obtained,

there is doubt on whether consensus has been achieved,

the subject matter is still under technical development, or

there is another reason precluding immediate publication as a Standard.

A Technical Specification is not allowed to conflict with an existing Standard. Table 2.0 explains the different designations for Technical Specifications listed in this document.

Table 2.0 – Designations for Technical Specifications


CEN/TS 12345 Technical Specification published by CEN

ISO/TS 12345 Technical Specification published by ISO

CEN ISO/TS 12345 ISO Technical Specification adopted as a European Technical Specification

S.R. CEN/TS 12345 European Technical Specification adopted as an Irish Standard Recommendation published by NSAI

S.R. CEN ISO/TS 12345 ISO Technical Specification adopted as a European Technical Specification and adopted as an Irish Standard Recommendation published by NSAI

7.2.3 Technical Report

A Technical Report is a document containing informative material not suitable to be published as a Standard or a Technical Specification. A TR can include, for example, data obtained from a survey carried out among the national members, data on work in other organizations or data on the state of the art in relation to national standards on a particular subject. Table 3.0 explains the different designations for Technical Reports listed in this document.

Table 3.0 – Designations for Technical Specifications


CEN/TR 12345 Technical Report published by CEN

ISO/TR 12345 Technical Report published by ISO

CEN ISO/TR 12345 ISO Technical Report adopted as a European Technical Report

S.R. CEN/TR 12345 European Technical Report adopted as an Irish Standard Recommendation published by NSAI

S.R. CEN ISO/TR 12345 ISO Technical Report adopted as a European Technical Report and adopted as an Irish Standard Recommendation


9

8 List of Irish National Standards and International Standard for the Oilfield

The information of the Standards listed is correct as of December 2015. Standards are continuously being revised and developed and the edition of the Standards listed are subject to routine change.

The list of Standards has been separated into 7 process sections for clarity, see Figure 1.0. Standards can be used in the various sections as appropriate.

Key:

1 Down hole, see 8.1

2 Subsea drilling and production equipment, see 8.2

3 Surface drilling, production and processing equipment and systems, see 8.3

4 Offshore structures (Semi submercibles), see 8.4

5 Offshore structures (Platforms, jackets and jack-ups), see 8.5

6 Pipeline transportation systems, see 8.6

7 Onshore processing, see 8.7

Figure 1.0 – Oilfield process sections


10

8.1 Down hole

The Standards listed in this section are specific to down hole equipment. Standards listed are from:

ISO/TC 67/SC 4 – Drilling and production equipment

ISO/TC 67/SC 5 - Casing, tubing and drill pipe

Standards applicable to down hole equipment

S.R. CEN ISO/TR 10400:2011

Petroleum and natural gas industries - Equations and calculations for the properties of casing, tubing, drill pipe and line

pipe used as casing or tubing (ISO/TR 10400:2007)

I.S. EN ISO 10405:2006

Petroleum and natural gas industries - Care and use of casing and tubing (ISO 10405:2006)

ISO 10407:1993

Petroleum and natural gas industries -- Drilling and production equipment -- Drill stem design and operating limits

I.S. EN ISO 10407-2:2008

Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Inspection and classification of used drill stem

elements (ISO 10407-2:2008)

I.S. EN ISO 10414-1:2008

Petroleum and natural gas industries - Field testing of drilling fluids - Part 1: Water-based fluids (ISO 10414-1:2008)

I.S. EN ISO 10414-2:2011

Petroleum and natural gas industries - Field testing of drilling fluids - Part 2: Oil-based fluids (ISO 10414-2:2011)

I.S. EN ISO 10416:2009

Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008)

I.S. EN ISO 10417:2004

Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress

(ISO 10417:2004)

I.S. EN ISO 10424-1:2004

Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (ISO 10424-1:2004)

I.S. EN ISO 10424-2:2007

Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Threading and gauging of rotary shouldered

thread connections (ISO 10424-2:2007)

I.S. EN ISO 10426-1:2009

Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification

(ISO 10426-1:2009)

I.S. EN ISO 10426-2:2003

Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements

(ISO 10426-2:2003)

I.S. EN ISO 10426-3:2004

Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well

cement formulations (ISO10426-3:2003)

I.S. EN ISO 10426-4:2005

Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of

foamed cement slurries at atmospheric pressure (ISO 10426-4:2004)

I.S. EN ISO 10426-5:2005

Petroleum and natural gas industries - Cements and materials for well cementing - Part 5: Determination of shrinkage

and expansion of well cement formulations at atmospheric pressure (ISO 10426-5:2004)


11

I.S. EN ISO 10426-6:2008

Petroleum and natural gas industries - Cements and materials for well cementing - Part 6: Methods for determining the

static gel strength of cement formulations (ISO 10426-6:2008)

I.S. EN ISO 10427-1:2002

Petroleum and natural gas industries - Casing centralizers - Part 1: Bow-spring casing centralizers (ISO 10427-1:2001)

I.S. EN ISO 10427-2:2004

Petroleum and natural gas industries - Equipment for well cementing - Part 2: Centralizer placement and stop-collar

testing (ISO 10427-2:2004)

I.S. EN ISO 10427-3:2004

Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float

equipment (ISO 10427-3:2003)

I.S. EN ISO 10432:2005

Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment (ISO 10432:2004)

I.S. EN ISO 11960:2014

Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells (ISO 11960:2014)

I.S. EN ISO 11961:2008

Petroleum and natural gas industries - Steel drill pipe (ISO 11961:2008)

ISO/PAS 12835:2013

Qualification of casing connections for thermal wells

I.S. EN ISO 13085:2014

Petroleum and Natural gas Industries - Aluminium Alloy Pipe for use as Tubing for Wells (ISO 13085:2014)

I.S. EN ISO 13500:2008+A1:2010

Petroleum and natural gas industries - Drilling fluid materials - Specifications and tests (ISO 13500:2008)

I.S. EN ISO 13501:2011

Petroleum and natural gas industries - Drilling fluids - Processing equipment evaluation (ISO 13501:2011)

I.S. EN ISO 13503-1:2011

Petroleum and natural gas industries - Completion fluids and materials - Part 1: Measurement of viscous properties of

completion fluids (ISO 13503-1:2011)

I.S. EN ISO 13503-2:2006+A1:2009

Petroleum and natural gas industries - Completion fluids and materials - Part 2: Measurement of properties of proppants

used in hydraulic fracturing and gravel-packing operations (ISO 13503-2:2006)

I.S. EN ISO 13503-3:2005

Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines

(ISO 13503-3:2005)

I.S. EN ISO 13503-4:2006

Petroleum and natural gas industries - Completion fluids and materials - Part 4: Procedure for measuring stimulation and

gravel-pack fluid leakoff under static conditions (ISO 13503-4:2006)

I.S. EN ISO 13503-5:2006

Petroleum and natural gas industries - Completion fluids and materials - Part 5: Procedures for measuring the long-term

conductivity of proppants (ISO 13503-5:2006)

I.S. EN ISO 13503-6:2014

Petroleum and Natural gas Industries - Completion Fluides and Materials - Part 6: Procedure for Measuring Leakoff of

Completion Fluids Under Dynamic Conditions (ISO 13503-6:2014)

I.S. EN ISO 13678:2012

Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing, line pipe

and drill stem elements (ISO 13678:2010)

I.S. EN ISO 13679:2006

Petroleum and natural gas industries - Procedures for testing casing and tubing connections (ISO 13679:2002)


12

I.S. EN ISO 13680:2010

Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling

stock - Technical delivery conditions (ISO 13680:2010)

I.S. EN ISO 14310:2008

Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2008)

I.S. EN ISO 14998:2013

Petroleum and Natural gas Industries - Downhole Equipment - Completion Accessories (ISO 14998:2013)

I.S. EN ISO 15136-1:2009

Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps

(ISO 15136-1:2009)

I.S. EN ISO 15136-2:2006

Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems

(ISO 15136-2:2006)

I.S. EN ISO 15463:2004

Petroleum and natural gas industries - Field inspection of new casing, tubing and plain-end drill pipe (ISO 15463:2003)

I.S. EN ISO 15546:2011

Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2011)

I.S. EN ISO 16070:2006

Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005)

ISO/TS 16530-2:2014

Well integrity - Part 2: Well integrity for the operational phase

I.S. EN ISO 17078-1:2005+A1:2010

Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels

(ISO 17078-1:2004)

I.S. EN ISO 17078-2:2007

Petroleum and natural gas industries - Drilling and production equipment - Part 2: Flow-control devices for side-pocket

mandrels (ISO 17078-2:2007)

I.S. EN ISO 17078-3:2009

Petroleum and natural gas industries - Drilling and production equipment - Part 3: Running tools, pulling tools and kick-

over tools and latches for side-pocket mandrels (ISO 17078-3:2009)

I.S. EN ISO 17078-4:2010

Petroleum and natural gas industries - Drilling and production equipment - Part 4: Practices for side-pocket mandrels and

related equipment (ISO 17078-4:2010)

I.S. EN ISO 17824:2014

Petroleum and Natural gas Industries - Downhole Equipment - Sand Screens (ISO 17824:2009)

I.S. EN ISO 27627:2014

Petroleum and Natural gas Industries - Aluminium Alloy Drill Pipe Thread Connection Gauging (ISO 27627:2014)

I.S. EN ISO 28781:2010

Petroleum and natural gas industries - Drilling and production equipment - Subsurface barrier valves and related

equipment (ISO 28781:2010)


13

8.2 Subsea drilling and production equipment

Standards listed are from:


Standards applicable to subsea drilling and production equipment

I.S. EN ISO 13628-1:2006+A1:2010

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General

requirements and recommendations (ISO 13628-1:2005)

I.S. EN ISO 13628-2:2006

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible

pipe systems for subsea and marine applications (ISO 13628-2:2006)

I.S. EN ISO 13628-3:2001

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 3: Through flowline

(TFL) systems (ISO 13628-3:2000)

I.S. EN ISO 13628-4:2010

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 4: Subsea wellhead

and tree equipment (ISO 13628-4:2010)

I.S. EN ISO 13628-5:2009

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals

(ISO 13628-5:2009)

I.S. EN ISO 13628-6:2006

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 6: Subsea production

control systems (ISO 13628-6:2006)

I.S. EN ISO 13628-7:2006

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 7: Completion/workover

riser systems (ISO 13628-7:2005)

I.S. EN ISO 13628-8:2006

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated

Vehicle (ROV) interfaces on subsea production systems (ISO 13628-8:2002)

I.S. EN ISO 13628-9:2006

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 9: Remotely Operated

Tool (ROT) intervention systems (ISO 13628-9:2000)

I.S. EN ISO 13628-10:2006

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for

bonded flexible pipe (ISO 13628-10:2006)

I.S. EN ISO 13628-11:2008

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe

systems for subsea and marine applications (ISO 13628-11:2007)

I.S. EN ISO 13628-15:2011

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 15: Subsea structures

and manifolds (ISO 13628-15:2011)


14

8.3 Surface drilling, production and processing equipment and systems


ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries


ISO/TC 67/SC 6 - Processing equipment and systems

Standards applicable to surface drilling, production and processing equipment and systems

I.S. EN ISO 10418:2003

Petroleum and natural gas industries - Offshore production installations - Basic surface process safety systems (ISO

10418:2003)

I.S. EN ISO 10423:2009

Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO

10423:2009)

I.S. EN ISO 13533:2002

Petroleum and natural gas industries - Drilling and production equipment - Drill-through equipment (ISO 13533:2001)

I.S. EN ISO 13534:2000

Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and

remanufacture of hoisting equipment (ISO 13534:2000)

I.S. EN ISO 13535:2000

Petroleum and natural gas industries - Drilling and production equipment - Hoisting equipment (ISO 13535:2000)

I.S. EN ISO 13626:2004

Petroleum and natural gas industries - Drilling and production equipment - Drilling and well-servicing structures (ISO

13626:2003)

I.S. EN ISO 13702:2015

Petroleum and natural gas industries - Control and migration of fires and explosions on offshore production installations

- Requirements and guidelines (ISO 13702:2015)

I.S. EN ISO 13703:2000

Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO

13703:2000)

I.S. EN ISO 14224:2006

Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for

equipment (ISO 14224:2006)

I.S. EN ISO 14692-1:2002

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols,

applications and materials (ISO 14692-1:2002)

I.S. EN ISO 14692-2:2002

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture

(ISO 14692-2:2002)

I.S. EN ISO 14692-3:2002

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-

3:2002)

I.S. EN ISO 14692-4:2002

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and

operation (ISO 14692-4:2002)


15

I.S. EN ISO 14693:2003

Petroleum and natural gas industries - Drilling and well-servicing equipment (ISO 14693:2003)

I.S. EN ISO 15138:2007

Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning (ISO

15138:2007)

I.S. EN ISO 15156-1:2015

Petroleum and natural gas industries - Materials for use in H[2]S-containing environments in oil and gas production -

Part 1: General principles for selection of cracking-resistant materials (ISO 15156-1:2015)

I.S. EN ISO 15156-2:2015


Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons (ISO 15156-2:2015)

I.S. EN ISO 15156-3:2015


Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2015)

I.S. EN ISO 15544:2010

Petroleum and natural gas industries - Offshore production installations - Requirements and guidelines for emergency

response (ISO 15544:2000, including Amd 1:2009)

I.S. EN ISO 15663-1:2006

Petroleum and natural gas industries - Life cycle costing - Part 1: Methodology (ISO 15663-1:2000)

ISO 15663-2:2001

Petroleum and natural gas industries -- Life-cycle costing -- Part 2: Guidance on application of methodology and

calculation methods

ISO 15663-3:2001

Petroleum and natural gas industries -- Life-cycle costing -- Part 3: Implementation guidelines

I.S. EN ISO 17776:2002

Petroleum and natural gas industries - Offshore production installations - Guidelines on tools and techniques for hazard

identification and risk assessment (ISO 17776:2000)

I.S. EN ISO 20815:2010

Petroleum, petrochemical and natural gas industries - Production assurance and reliability management (ISO

20815:2008, Corrected version 2009-06-15)

I.S. EN ISO 21457:2010

Petroleum, petrochemical and natural gas industries -- Materials selection and corrosion control for oil and gas

production systems

I.S. EN ISO 23936-1:2009

Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and

gas production - Part 1: Thermoplastics (ISO 23936-1:2009)

I.S. EN ISO 23936-2:2011

Petroleum, Petrochemical and Natural gas Industries - Non-metallic Materials in Contact With Media Related to oil and

gas Production - Part 2: Elastomers (ISO 23936-2:2011)

S.R. CEN ISO/TS 27469:2011

Petroleum, petrochemical and natural gas industries - Method of test for fire dampers (ISO/TS 27469:2010)

I.S. EN ISO 27509:2012

Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2012)

S.R. CEN ISO/TS 29001:2011

Petroleum, petrochemical and natural gas industries - Sector-specific quality management systems - Requirements for

product and service supply organizations (ISO/TS 29001:2010)


16

8.4 Offshore structures (Semi submersibles)



ISO/TC 67/SC 7 – Offshore structures

Standards applicable to semi submersibles offshore structures

I.S. EN ISO 13624-1:2009

Petroleum and natural gas industries - Drilling and production equipment - Part 1: Design and operation of marine drilling

riser equipment (ISO 13624-1:2009)

SR CEN ISO/TR 13624-2:2013

Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Deepwater drilling riser

methodologies, operations, and integrity technical report (ISO/TR 13624-2:2009)

I.S. EN ISO 13625:2002

Petroleum and natural gas industries - Drilling and production equipment - Marine drilling riser couplings

(ISO 13625:2002)

I.S. EN ISO 19901-7:2013

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for

floating offshore structures and mobile offshore units (ISO 19901-7:2013)

I.S. EN ISO 19904-1:2006

Petroleum and natural gas industries - Floating offshore structures - Part 1: Monohulls, semi-submersibles and spars

(ISO 19904-1:2006)


17

8.5 Offshore structures (Platforms, jackets and jack-ups)



ISO/TC 67/SC 7 – Offshore structures

Standards applicable to Offshore structures (Platforms, jackets and jack-ups)

I.S. EN ISO 19900:2013

Petroleum and natural gas industries - General requirements for offshore structures (ISO 19900:2013)

I.S. EN ISO 19901-1:2006

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design and operating

considerations (ISO 19901-1:2005)

I.S. EN ISO 19901-2:2005

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 2: Seismic design procedures and

criteria (ISO 19901-2:2004)

I.S. EN ISO 19901-3:2014

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure

(ISO 19901-3:2014)

I.S. EN ISO 19901-4:2003

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 4: Geotechnical and foundation design

considerations (ISO 19901-4:2003)

I.S. EN ISO 19901-5:2003

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 5: Weight control during engineering

and construction (ISO 19901-5:2003)

I.S. EN ISO 19901-6:2009

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 6: Marine operations

(ISO 19901-6:2009)

I.S. EN ISO 19901-8:2015

Petroleum and Natural gas Industries - Specific Requirements for Offshore Structures - Part 8: Marine Soil Investigations

(ISO 19901-8:2014)

I.S. EN ISO 19902:2007+A1:2013

Petroleum and natural gas industries - Fixed steel offshore structures (ISO 19902:2007)

I.S. EN ISO 19903:2006

Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006)

I.S. EN ISO 19905-1:2012

Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 1: Jack-ups (ISO 19905-1:2012)

SR CEN ISO/TR 19905-2:2013

Petroleum and Natural gas Industries - Sitespecific Assessment of Mobile Offshore Units - Part 2: Jack-ups Commentary and

Detailed Sample Calculation (ISO/TR 19905-2:2012)

I.S. EN ISO 19906:2010

Petroleum and natural gas industries - Arctic offshore structures (ISO 19906:2010)


18

8.6 Pipeline transportation systems


CEN ECISS/TC 110 - Steel tubes, and iron and steel fittings

CEN/TC 12 - Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries

ISO/TC 67/SC 2 - Pipeline transportation systems

Standards applicable to pipeline transportation systems

I.S. EN ISO 3183:2012

Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2012)

ISO 12490:2011

Petroleum and natural gas industries -- Mechanical integrity and sizing of actuators and mounting kits for pipeline valves

I.S. EN ISO 12736:2014

Petroleum and Natural gas Industries - wet Thermal Insulation Coatings for Pipelines, Flow Lines, Equipment and Subsea

Structures (ISO 12736:2014)

SR CEN ISO/TS 12747:2013

Petroleum and natural gas industries -- Pipeline transportation systems -- Recommended practice for pipeline life extension

(ISO/TS 12747:2011)

I.S. EN 13942:2009

Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified)

I.S. EN 14161:2011+A1:2015

Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2009 modified)

I.S. EN 14163:2001

Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000 modified)

I.S. EN 14870-1:2011

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction

bends (ISO 15590-1:2009 modified)

I.S. EN 14870-2:2004

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings

(ISO 15590-2:2003 modified)

I.S. EN 14870-3:2006

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges

(ISO 15590-3:2004, modified)

I.S. EN ISO 14723:2009

Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2009)

ISO 15589-1:2015

Petroleum and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 1: On-land pipelines

I.S. EN ISO 15589-2:2014

Petroleum, petrochemical and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 2: Offshore

pipelines (ISO 15589-2:2012)

I.S. EN ISO 16708:2006

Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods (ISO 16708:2006)

I.S. EN ISO 21329:2004

Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors

(ISO 21329:2004)


19

I.S. EN ISO 21809-2:2014

Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems

- Part 2: Fusion-bonded epoxy coatings (ISO 21809-2:2014)

ISO 21809-3:2008+A1:2011

Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation

systems -- Part 3: Field joint coatings

ISO 21809-4:2009

Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation

systems -- Part 4: Polyethylene coatings (2-layer PE)

I.S. EN ISO 21809-5:2010

Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems

- Part 5: External concrete coatings (ISO 21809-5:2010)

8.7 Onshore processing

Standards listed have been developed:

CEN/TC 12 - Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries

CEN/TC 69 – Industrial valves ISO/TC 60/SC 2 – Gears - Gear capacity calculation


ISO/TC 67/SC 6 – Processing equipment and systems

ISO/TC 115/SC 3 – Pumps - Installation and special application

ISO/TC 118/SC 1 – Compressors and pneumatic tools, machines and equipment- Process compressors

ISO/TC 153 – Valves

ISO/TC 192 – Gas turbines

Standards applicable to onshore processing

I.S. EN ISO 3977-5:2003

Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries (ISO 3977-5:2001)

ISO 10428:1993

Petroleum and natural gas industries -- Sucker rods (pony rods, polished rods, couplings and sub-couplings) --

Specification

ISO 10431:1993

Petroleum and natural gas industries -- Pumping units -- Specification

I.S. EN ISO 10434:2004

Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries (ISO 10434:2004)

I.S. EN ISO 10437:2003

Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications (ISO 10437:2003)

I.S. EN ISO 10438-1:2007

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries -

Part 1: General requirements (ISO 10438-1:2007)


20

I.S. EN ISO 10438-2:2007


Part 2: Special-purpose oil systems (ISO 10438-2:2007)

I.S. EN ISO 10438-3:2007


Part 3: General-purpose oil systems (ISO 10438-3:2007)

I.S. EN ISO 10438-4:2007


Part 4: Self-acting gas seal support systems (ISO 10438-4:2007)

I.S. EN ISO 10439-1:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors -

Part 1: General requirements (ISO 10439-1:2015)

I.S. EN ISO 10439-2:2015

Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors -

Part 2: Non-integrally geared centrifugal and axial compressors (ISO 10439-2:2015)

I.S. EN ISO 10439-3:2015

Petroleum, petrochemical and natural gas industries - axial and centrifugal compressors and expander-compressors -

Part 3: Integrally geared centrifugal compressors (ISO 10439-3:2015)

I.S. EN ISO 10439-4:2015

Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors -

Part 4: Expander-compressors (ISO 10439-4:2015)

I.S. EN ISO 10440-1:2007

Petroleum, petrochemical and natural gas industries - Rotary-type positive-displacement compressors - Part 1: Process

compressors (ISO 10440-1:2007)

I.S. EN ISO 10440-2:2001

Petroleum and natural gas industries - Rotary-type positive-displacement compressors - Part 2: Packaged air

compressors (oil-free) (ISO 10440-2:2001)

I.S. EN ISO 10441:2007

Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-

purpose applications (ISO 10441:2007)

I.S. EN ISO 10442:2002

Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors

(ISO 10442:2002)

I.S. EN ISO 12211:2012

Petroleum, Petrochemical and Natural gas Industries - Spiral Plate Heat Exchangers (ISO 12211:2012)

I.S. EN ISO 12212:2012

Petroleum, Petrochemical and Natural gas Industries - Hairpin-type Heat Exchangers (ISO 12212:2012)

I.S. EN ISO 13631:2002

Petroleum and natural gas industries - Packaged reciprocating gas compressors (ISO 13631:2002)

I.S. EN ISO 13691:2002

Petroleum and natural gas industries - High-speed special-purpose gear units (ISO 13691:2001)

I.S. EN ISO 13704:2007

Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries

(ISO 13704:2007)

I.S. EN ISO 13705:2012

Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service (ISO 13705:2012)

I.S. EN ISO 13706:2011

Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2011)


21

ISO 13707:2000

Petroleum and natural gas industries -- Reciprocating compressors

I.S. EN ISO 13709:2009

Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009)

I.S. EN ISO 13710:2004

Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps (ISO 13710:2004)

I.S. EN ISO 14691:2008

Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-

purpose applications (ISO 14691:2008)

I.S. EN ISO 15547-1:2005

Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat

exchangers (ISO 15547-1:2005)

I.S. EN ISO 15547-2:2005

Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin

heat exchangers (ISO 15547-2:2005)

S.R. CEN/TR 14549:2004

Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment

Directive

I.S. EN ISO 15761:2002

Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries

(ISO 15761:2002)

I.S. EN ISO 16812:2007

Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers (ISO 16812:2007)

I.S. EN ISO 16961:2015

Petroleum, Petrochemical and Natural gas Industries - Internal Coating and Lining of Steel Storage Tanks

(ISO 16961:2015)

I.S. EN ISO 17292:2015

Metal ball valves for petroleum, petrochemical and allied industries (ISO 17292:2015)

I.S. EN ISO 21049:2004

Pumps - Shaft sealing systems for centrifugal and rotary pumps (ISO 21049:2004)

I.S. EN ISO 23251:2007+A1:2008

Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems (ISO 23251:2006)

I.S. EN ISO 24817:2015

Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design,

installation, testing and inspection (ISO 24817:2015)

I.S. EN ISO 25457:2008

Petroleum, petrochemical and natural gas industries - Flare details for general refinery and petrochemical service

(ISO 25457:2008)

I.S. EN ISO 28300:2008

Petroleum, petrochemical and natural gas industries - Venting of atmospheric and low-pressure storage tanks

(ISO 28300:2008)


22

9 Information on each Technical Committee

The information in this section is for reference only. The Standards listed are those published by the Technical Committee and are not all utilised in the undertakings within the scope of work of the PEETSC.

9.1 ISO/TC 67 - Structure

ISO Technical Committee 67 is a large TC with a structure more complicated than other TC's due to the large scope of work and Standards covering this area. Each relevant part of the TC is addressed within this section 9.1.

9.1.1 ISO/TC 67

Title: Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries

Secretariat: NEN (Dutch National Standards Body) Secretary: Mrs. Jeannette Hofman Chairperson: Vacant ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager: Mrs. Laura Mathew Creation date: 1947

The scope of ISO/TC 67 is the standardization of the materials, equipment and offshore structures used in the drilling, production, transport by pipelines and processing of liquid and gaseous hydrocarbons within the petroleum, petrochemical and natural gas industries.

Excluded from the scope are aspects of offshore structures subject to International Maritime Organization (IMO) requirements which are covered by ISO/TC 8 Ships and marine technology.

Total number of published ISO standards related to the TC and its SCs (number includes updates):

198

Number of published ISO standards under the direct responsibility of TC 67 (number includes updates):

23

(P) Participating countries: 33

(O) Observing countries: 33

Irelands membership status O- member

Sub-Committees of ISO/TC 67

TC Sub-Committee SC Title Irelands membership status

ISO/TC 67/SC 2 Pipeline transportation systems P

ISO/TC 67/SC 3 Drilling and completion fluids, and well cements -

http://www.iso.org/iso/home/standards_development/list_of_iso_technical_committees/technical_committee_contact.htm?commid=49506

mailto:[email protected]


http://www.iso.org/iso/home/standards_development/list_of_iso_technical_committees/iso_technical_committee.htm?commid=49532



23

ISO/TC 67/SC 4 Drilling and production equipment -

ISO/TC 67/SC 5 Casing, tubing and drill pipe -

ISO/TC 67/SC 6 Processing equipment and systems -

ISO/TC 67/SC 7 Offshore structures -

ISO/TC 67/SC 8 Arctic operations -

ISO/TC 67/SC 9 Liquefied natural gas installations and equipment -

Working Groups of ISO/TC 67

ISO/TC 67/EC/MC Executive committee and Management committee

ISO/TC 67/WG 2 Conformity assessment

TC 67/WG 4 Reliability Engineering and technology

TC 67/WG 5 Aluminium alloy pipes

TC 67/WG 7 Corrosion resistant materials

TC 67/WG 8 Materials, corrosion control, welding and jointing, and non-destructive examination (NDE)

TC 67/WG 10 Liquefied Natural Gas (LNG) installations and equipment

TC 67/WG 11 Coating and lining of structures and equipment

TC 67/WG 12 CO2 aspects

TC 67/JWG 13 Joint ISO/TC 67 - ISO TC 8/SC8 WG; Cryogenic spillage

Standards published by ISO /TC 67

ISO/TR 12489:2013 Petroleum, petrochemical and natural gas industries -- Reliability modelling and calculation of safety systems

ISO 13085:2014 Petroleum and natural gas industries -- Aluminium alloy pipe for use as tubing for wells

ISO 13879:1999 Petroleum and natural gas industries -- Content and drafting of a functional specification

ISO 13880:1999 Petroleum and natural gas industries -- Content and drafting of a technical specification

ISO/TR 13881:2000 Petroleum and natural gas industries -- Classification and conformity assessment of products, processes and services

ISO 14224:2006 Petroleum, petrochemical and natural gas industries -- Collection and exchange of reliability and maintenance data for







24

equipment

ISO 15156-1:2015 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 1: General principles for selection of cracking-resistant materials

ISO 15156-2:2015 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons

ISO 15156-3:2015 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys

ISO 15546:2011 Petroleum and natural gas industries -- Aluminium alloy drill pipe

ISO 15663-1:2000 Petroleum and natural gas industries -- Life cycle costing -- Part 1: Methodology

ISO 15663-2:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 2: Guidance on application of methodology and calculation methods

ISO 15663-3:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 3: Implementation guidelines

ISO 16961:2015 Petroleum, petrochemical and natural gas industries -- Internal coating and lining of steel storage tanks

ISO 17945:2015 Petroleum, petrochemical and natural gas industries -- Metallic materials resistant to sulfide stress cracking in corrosive petroleum refining environments

ISO/TS 17969:2015 Petroleum, petrochemical and natural gas industries -- Guidelines on competency for personnel

ISO 20312:2011 Petroleum and natural gas industries -- Design and operating limits of drill strings with aluminium alloy components

ISO 20815:2008 Petroleum, petrochemical and natural gas industries -- Production assurance and reliability management

ISO 21457:2010 Petroleum, petrochemical and natural gas industries -- Materials selection and corrosion control for oil and gas production systems

ISO 23936-1:2009 Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 1: Thermoplastics

ISO 23936-2:2011 Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 2: Elastomers

ISO 27627:2014 Petroleum and natural gas industries -- Aluminium alloy drill pipe thread connection gauging

ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries -- Sector-specific quality management systems -- Requirements for product and service supply organizations


25

9.1.2 ISO/TC 67/SC 2

Title: Pipeline transportation systems

Secretariat: UNI (Italian National Standards Body) Twinned secretariat: SAC Secretary: Mr Giuliano Corbella Twinned secretary: Mr. Changyi Qin Chairperson: Mr. Denis Tikhomirov until end 2015 ISO Central Secretariat contact: Mrs. Kirsi Silander Editorial Programme Manager(s): Mrs. Laura Mathew

Number of published ISO standards under the direct responsibility of TC 67/SC 2 (number includes updates):

22



Irelands membership status P

Standards published by ISO/TC 67/SC 2

ISO 3183:2012 Petroleum and natural gas industries -- Steel pipe for pipeline transportation systems

ISO 12490:2011 Petroleum and natural gas industries -- Mechanical integrity and sizing of actuators and mounting kits for pipeline valves

ISO 12736:2014 Petroleum and natural gas industries -- Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures

ISO/TS 12747:2011 Petroleum and natural gas industries -- Pipeline transportation systems -- Recommended practice for pipeline life extension

ISO 13623:2009 Petroleum and natural gas industries -- Pipeline transportation systems

ISO 13847:2013 Petroleum and natural gas industries -- Pipeline transportation systems -- Welding of pipelines

ISO 14313:2007 Petroleum and natural gas industries -- Pipeline transportation systems -- Pipeline valves

ISO 14313:2007/Cor 1:2009

ISO 14723:2009 Petroleum and natural gas industries -- Pipeline transportation systems -- Subsea pipeline valves

ISO 15589-1:2015 Petroleum and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 1: On-land pipelines

ISO 15589-2:2012 Petroleum, petrochemical and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 2: Offshore pipelines

ISO 15590-1:2009 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 1: Induction bends


26

ISO 15590-2:2003 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 2: Fittings

ISO 15590-3:2004 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 3: Flanges

ISO 16708:2006 Petroleum and natural gas industries -- Pipeline transportation systems -- Reliability-based limit state methods

ISO 21329:2004 Petroleum and natural gas industries -- Pipeline transportation systems -- Test procedures for mechanical connectors

ISO 21809-1:2011 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 1: Polyolefin coatings (3-layer PE and 3-layer PP)

ISO 21809-2:2014 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 2: Fusion-bonded epoxy coatings

ISO 21809-3:2008 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 3: Field joint coatings

ISO 21809-3:2008/Amd 1:2011

ISO 21809-4:2009 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 4: Polyethylene coatings (2-layer PE)

ISO 21809-5:2010 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 5: External concrete coatings

9.1.3 ISO/TC 67/SC 3

Title: Drilling and completion fluids, and well cements

Secretariat: SN (Norwegian National Standards Body) Secretary: Ms Inghild Kaarstad Chairperson: Vacant ISO Central Secretariat contact: Mrs. Kirsi Silander - van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew


28



Irelands membership status -


ISO 10414-1:2008 Petroleum and natural gas industries -- Field testing of drilling fluids -- Part 1: Water-based fluids


27

ISO 10414-2:2011 Petroleum and natural gas industries -- Field testing of drilling fluids -- Part 2: Oil-based fluids

ISO 10416:2008 Petroleum and natural gas industries -- Drilling fluids -- Laboratory testing

ISO 10426-1:2009 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 1: Specification

ISO 10426-1:2009/Cor 1:2010

ISO 10426-1:2009/Cor 2:2012

ISO 10426-2:2003 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 2: Testing of well cements

ISO 10426-2:2003/Cor 1:2006

ISO 10426-2:2003/Amd 1:2005 Water-wetting capability testing

ISO 10426-3:2003 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 3: Testing of deepwater well cement formulations

ISO 10426-4:2004 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure

ISO 10426-5:2004 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure

ISO 10426-6:2008 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 6: Methods for determining the static gel strength of cement formulations

ISO 10427-1:2001 Petroleum and natural gas industries -- Equipment for well cementing -- Part 1: Casing bow-spring centralizers

ISO 10427-2:2004 Petroleum and natural gas industries -- Equipment for well cementing -- Part 2: Centralizer placement and stop-collar testing

ISO 10427-3:2003 Petroleum and natural gas industries -- Equipment for well cementing -- Part 3: Performance testing of cementing float equipment

ISO 13500:2008 Petroleum and natural gas industries -- Drilling fluid materials -- Specifications and tests

ISO 13500:2008/Cor 1:2009

ISO 13500:2008/Amd 1:2010 Barite 4,1

ISO 13501:2011 Petroleum and natural gas industries -- Drilling fluids -- Processing equipment evaluation

ISO 13503-1:2011 Petroleum and natural gas industries -- Completion fluids and materials -- Part 1: Measurement of viscous properties of completion fluids

ISO 13503-2:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations

ISO 13503-2:2006/Amd 1:2009 Addition of Annex B: Proppand specification

ISO 13503-3:2005 Petroleum and natural gas industries -- Completion fluids and materials -- Part 3: Testing of heavy brines


28

ISO 13503-3:2005/Cor 1:2006

ISO 13503-4:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 4: Procedure for measuring stimulation and gravel-pack fluid leak off under static conditions

ISO 13503-5:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 5: Procedures for measuring the long-term conductivity of proppants

ISO 13503-6:2014 Petroleum and natural gas industries -- Completion fluids and materials -- Part 6: Procedure for measuring leakoff of completion fluids under dynamic conditions

9.1.4 ISO/TC 67/SC 4

Title: Drilling and production equipment

Secretariat: ANSI Secretary: Mr. Ed Barrett Chairperson: Mr Oliver C. Moghissi until end 2016 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew


52





ISO 10407:1993 Petroleum and natural gas industries -- Drilling and production equipment -- Drill stem design and operating limits

ISO 10407-2:2008 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 2: Inspection and classification of used drill stem elements

ISO 10407-2:2008/Cor 1:2009

ISO 10417:2004 Petroleum and natural gas industries -- Subsurface safety valve systems -- Design, installation, operation and redress

ISO 10423:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Wellhead and christmas tree equipment

ISO 10424-1:2004 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 1: Rotary drill stem elements

ISO 10424-2:2007 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 2: Threading and gauging of rotary shouldered thread connections

ISO 10428:1993 Petroleum and natural gas industries -- Sucker rods (pony rods, polished rods, couplings and sub-couplings) --


29

Specification

ISO 10431:1993 Petroleum and natural gas industries -- Pumping units -- Specification

ISO 10432:2004 Petroleum and natural gas industries -- Downhole equipment -- Subsurface safety valve equipment

ISO 13354:2014 Petroleum and natural gas industries -- Drilling and production equipment -- Shallow gas diverter equipment

ISO 13533:2001 Petroleum and natural gas industries -- Drilling and production equipment -- Drill-through equipment

ISO 13533:2001/Cor 1:2005

ISO 13534:2000 Petroleum and natural gas industries -- Drilling and production equipment -- Inspection, maintenance, repair and remanufacture of hoisting equipment

ISO 13535:2000 Petroleum and natural gas industries -- Drilling and production equipment -- Hoisting equipment

ISO 13624-1:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 1: Design and operation of marine drilling riser equipment

ISO/TR 13624-2:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Deepwater drilling riser methodologies, operations, and integrity technical report

ISO 13625:2002 Petroleum and natural gas industries -- Drilling and production equipment -- Marine drilling riser couplings

ISO 13626:2003 Petroleum and natural gas industries -- Drilling and production equipment -- Drilling and well-servicing structures

ISO 13628-1:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 1: General requirements and recommendations

ISO 13628-1:2005/Amd 1:2010 Revised Clause 6

ISO 13628-2:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 2: Unbonded flexible pipe systems for subsea and marine applications

ISO 13628-2:2006/Cor 1:2009

ISO 13628-3:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 3: Through flowline (TFL) systems

ISO 13628-4:2010 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 4: Subsea wellhead and tree equipment

ISO 13628-4:2010/Cor 1:2011

ISO 13628-5:2009 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 5: Subsea umbilicals

ISO 13628-6:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 6: Subsea production control systems

ISO 13628-7:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 7: Completion/workover riser systems

ISO 13628-8:2002 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 8: Remotely Operated


30

Vehicle (ROV) interfaces on subsea production systems

ISO 13628-8:2002/Cor 1:2005

ISO 13628-9:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 9: Remotely Operated Tool (ROT) intervention systems

ISO 13628-10:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 10: Specification for bonded flexible pipe

ISO 13628-11:2007 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 11: Flexible pipe systems for subsea and marine applications

ISO 13628-11:2007/Cor 1:2008

ISO 13628-15:2011 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 15: Subsea structures and manifolds

ISO 14310:2008 Petroleum and natural gas industries -- Downhole equipment -- Packers and bridge plugs

ISO 14693:2003 Petroleum and natural gas industries -- Drilling and well-servicing equipment

ISO 15136-1:2009 Petroleum and natural gas industries -- Progressing cavity pump systems for artificial lift -- Part 1: Pumps

ISO 15136-2:2006 Petroleum and natural gas industries -- Progressing cavity pump systems for artificial lift -- Part 2: Surface-drive systems

ISO 16070:2005 Petroleum and natural gas industries -- Downhole equipment -- Lock mandrels and landing nipples

ISO/TS 16530-2:2014 Well integrity -- Part 2: Well integrity for the operational phase

ISO 17078-1:2004 Petroleum and natural gas industries -- Drilling and production equipment -- Part 1: Side-pocket mandrels

ISO 17078-1:2004/Amd 1:2010

ISO 17078-2:2007 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Flow-control devices for side-pocket mandrels

ISO 17078-2:2007/Cor 1:2009

ISO 17078-3:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels

ISO 17078-4:2010 Petroleum and natural gas industries -- Drilling and production equipment -- Part 4: Practices for side-pocket mandrels and related equipment

ISO 17824:2009 Petroleum and natural gas industries -- Downhole equipment -- Sand screens

ISO 28781:2010 Petroleum and natural gas industries -- Drilling and production equipment --Subsurface barrier valves and related equipment


31

9.1.5 ISO/TC 67/SC 5

Title: Casing, tubing and drill pipe

Secretariat: JISC (Japan Iron and Steel Federation) Secretary: Mr. Tsunehiro Ise Chairperson: Mr Tsuneo Murase until end 2019 ISO Central Secretariat contact: Mrs. Kirsi Silander -van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew


11





ISO/TR 10400:2007 Petroleum and natural gas industries -- Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing

ISO 10405:2000 Petroleum and natural gas industries -- Care and use of casing and tubing

ISO 11960:2014 Petroleum and natural gas industries -- Steel pipes for use as casing or tubing for wells

ISO 11961:2008 Petroleum and natural gas industries -- Steel drill pipe

ISO 11961:2008/Cor 1:2009

ISO/PAS 12835:2013 Qualification of casing connections for thermal wells

ISO 13678:2010 Petroleum and natural gas industries -- Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements

ISO 13679:2002 Petroleum and natural gas industries -- Procedures for testing casing and tubing connections

ISO 13680:2010 Petroleum and natural gas industries -- Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock -- Technical delivery conditions

ISO 15463:2003 Petroleum and natural gas industries -- Field inspection of new casing, tubing and plain-end drill pipe

ISO 15463:2003/Cor 1:2009


32

9.1.6 ISO/TC 67/SC 6

Title: Processing equipment and systems

Secretariat: AFNOR (French National Standards Body) Secretary: M Nicolas Marcq Chairperson: M. Joël Fort (France) until end 2017 ISO Central Secretariat contact: Mrs. Kirsi Silander -van Hunen


40





ISO 10418:2003 Petroleum and natural gas industries -- Offshore production installations -- Analysis, design, installation and testing of basic surface process safety systems

ISO 10418:2003/Cor 1:2008

ISO 10437:2003 Petroleum, petrochemical and natural gas industries -- Steam turbines -- Special-purpose applications

ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 1: General requirements

ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 2: Special-purpose oil systems

ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 3: General-purpose oil systems

ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 4: Self-acting gas seal support systems

ISO 10441:2007 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- Special-purpose applications

ISO 12211:2012 Petroleum, petrochemical and natural gas industries -- Spiral plate heat exchangers

ISO 12212:2012 Petroleum, petrochemical and natural gas industries -- Hairpin-type heat exchangers

ISO 13702:2015 Petroleum and natural gas industries -- Control and mitigation of fires and explosions on offshore production installations -- Requirements and guidelines

ISO 13703:2000 Petroleum and natural gas industries -- Design and installation of piping systems on offshore production platforms

ISO 13703:2000/Cor 1:2002


33

ISO 13704:2007 Petroleum, petrochemical and natural gas industries -- Calculation of heater-tube thickness in petroleum refineries

ISO 13704:2007/Cor 1:2008

ISO 13705:2012 Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service

ISO 13706:2011 Petroleum, petrochemical and natural gas industries -- Air-cooled heat exchangers

ISO 14691:2008 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- General-purpose applications

ISO 14692-1:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 1: Vocabulary, symbols, applications and materials

ISO 14692-2:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 2: Qualification and manufacture

ISO 14692-2:2002/Cor 1:2005

ISO 14692-3:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 3: System design

ISO 14692-3:2002/Cor 1:2005

ISO 14692-4:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 4: Fabrication, installation and operation

ISO 14692-4:2002/Cor 1:2006

ISO 15138:2007 Petroleum and natural gas industries -- Offshore production installations -- Heating, ventilation and air-conditioning

ISO 15544:2000/Amd 1:2009 Petroleum and natural gas industries -- Offshore production installations -- Requirements and guidelines for emergency response

ISO 15547-1:2005 Petroleum, petrochemical and natural gas industries -- Plate-type heat exchangers -- Part 1: Plate-and-frame heat exchangers

ISO 15547-2:2005 Petroleum, petrochemical and natural gas industries -- Plate-type heat exchangers -- Part 2: Brazed aluminium plate-fin heat exchangers

ISO 15649:2001 Petroleum and natural gas industries -- Piping

ISO 16812:2007 Petroleum, petrochemical and natural gas industries -- Shell-and-tube heat exchangers

ISO 17776:2000 Petroleum and natural gas industries -- Offshore production installations -- Guidelines on tools and techniques for hazard identification and risk assessment

ISO/TS 24817:2015 Petroleum, petrochemical and natural gas industries -- Composite repairs for pipework -- Qualification and design, installation, testing and inspection

ISO 25457:2008 Petroleum, petrochemical and natural gas industries -- Flare details for general refinery and petrochemical service

ISO/TS 27469:2010 Petroleum, petrochemical and natural gas industries - Method of test for fire dampers

ISO 27509:2012 Petroleum and natural gas industries -- Compact flanged connections with IX seal ring


34

ISO 28300:2008 Petroleum, petrochemical and natural gas industries -- Venting of atmospheric and low-pressure storage tanks

ISO 28300:2008/Cor 1:2009

9.1.7 ISO/TC 67/SC 7

Title: Offshore structures

Secretariat: BSI (UK National Standards Body) Secretary: Dr. Charles A. Whitlock Chairperson: Mr. Philip Smedley (United Kingdom) until end 2016 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew


17





ISO 19900:2013 Petroleum and natural gas industries -- General requirements for offshore structures

ISO 19901-1:2015 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 1: Metocean design and operating considerations

ISO 19901-2:2004 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 2: Seismic design procedures and criteria

ISO 19901-3:2014 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 3: Topsides structure

ISO 19901-4:2003 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 4: Geotechnical and foundation design considerations

ISO 19901-5:2003 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 5: Weight control during engineering and construction

ISO 19901-6:2009 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 6: Marine operations

ISO 19901-6:2009/Cor 1:2011

ISO 19901-7:2005 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units

ISO 19901-8:2014 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 8: Marine soil investigations

ISO 19902:2007


35

Petroleum and natural gas industries -- Fixed steel offshore structures

ISO 19902:2007/Amd 1:2013

ISO 19903:2006 Petroleum and natural gas industries -- Fixed concrete offshore structures

ISO 19904-1:2006 Petroleum and natural gas industries -- Floating offshore structures -- Part 1: Monohulls, semi-submersibles and spars

ISO 19905-1:2012 Petroleum and natural gas industries -- Site-specific assessment of mobile offshore units -- Part 1: Jack-ups

ISO/TR 19905-2:2012 Petroleum and natural gas industries -- Site-specific assessment of mobile offshore units -- Part 2: Jack-ups commentary and detailed sample calculation

ISO 19906:2010 Petroleum and natural gas industries -- Arctic offshore structures

9.1.8 ISO/TC 67/SC 8

Title: Arctic operations

Secretariat: GOST R (Russian Federation National Standards Body) Secretary: Mrs. Liudmila Zalevskaya Chairperson: Mr. Mikhail Rusakov until end 2017 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew Creation date: 2011


0




This Sub-Committee has not yet published any standards.



36

9.1.9 ISO/TC 67/SC 9

Title: Liquefied natural gas installations and equipment

Secretariat: AFNOR (French National Standards Body) Secretary: M. Christophe Erhel Chairperson: M. Max Nussbaum until end 2020 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew Creation date: 2015


5





ISO/TS 16901:2015 Guidance on performing risk assessment in the design of onshore LNG installations including the ship/shore interface

ISO 16903:2015 Petroleum and natural gas industries -- Characteristics of LNG, influencing the design, and material selection

ISO/TR 17177:2015 Petroleum and natural gas industries -- Guidelines for the marine interfaces of hybrid LNG terminals

ISO/TS 18683:2015 Guidelines for systems and installations for supply of LNG as fuel to ships

ISO 28460:2010 Petroleum and natural gas industries -- Installation and equipment for liquefied natural gas -- Ship-to-shore interface and port operations

9.2 ISO/TC 60

Title: Gears

Secretariat: ANSI Secretary: Mr. Amir Aboutaleb Chairperson: Mr. Jens Demtröder ISO Central Secretariat contact: M. Pierre-Charles Bazin de Caix Creation date: 1947

The Scope ISO/TC 60 is the standardization in the field of gears, including terminology, nominal dimensions, tolerances, and tools for manufacturing and control.


63


37


25




Subcommittees of ISO/TC 60

ISO/TC 60/SC 1 Nomenclature and wormgearing

ISO/TC 60/SC 2 Gear capacity calculation

Working Groups of ISO/TC 60

ISO/TC 60/JWG 1 Joint ISO/TC 60-IEC/TC 88 WG: Wind turbine gearboxes

ISO/TC 60/WG 2 Accuracy of gears


ISO 6336-1:2006

Calculation of load capacity of spur and helical gears -- Part 1: Basic principles, introduction and general influence factors

ISO 6336-1:2006/Cor 1:2008

ISO 6336-2:2006

Calculation of load capacity of spur and helical gears -- Part 2: Calculation of surface durability (pitting)

ISO 6336-2:2006/Cor 1:2008

ISO 6336-3:2006

Calculation of load capacity of spur and helical gears -- Part 3: Calculation of tooth bending strength

ISO 6336-3:2006/Cor 1:2008

ISO 6336-5:2003

Calculation of load capacity of spur and helical gears -- Part 5: Strength and quality of materials

ISO 6336-6:2006

Calculation of load capacity of spur and helical gears -- Part 6: Calculation of service life under variable load

ISO 6336-6:2006/Cor 1:2007

ISO 9083:2001

Calculation of load capacity of spur and helical gears -- Application to marine gears

ISO 9085:2002

Calculation of load capacity of spur and helical gears -- Application for industrial gears

ISO 10300-1:2014

Calculation of load capacity of bevel gears -- Part 1: Introduction and general influence factors

ISO 10300-2:2014


38

Calculation of load capacity of bevel gears -- Part 2: Calculation of surface durability (pitting)

ISO 10300-3:2014

Calculation of load capacity of bevel gears -- Part 3: Calculation of tooth root strength

ISO 13691:2001

Petroleum and natural gas industries -- High-speed special-purpose gear units

ISO 14104:2014

Gears -- Surface temper etch inspection after grinding, chemical method

ISO/TR 14179-1:2001

Gears -- Thermal capacity -- Part 1: Rating gear drives with thermal equilibrium at 95 °C sump temperature

ISO/TR 14179-2:2001

Gears -- Thermal capacity -- Part 2: Thermal load-carrying capacity

ISO 14635-1:2000

Gears -- FZG test procedures -- Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils

ISO 14635-2:2004

Gears -- FZG test procedures -- Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of

high EP oils

ISO 14635-3:2005

Gears -- FZG test procedures -- Part 3: FZG test method A/2, 8/50 for relative scuffing load-carrying capacity and wear

characteristics of semifluid gear greases

ISO/TR 15144-1:2014

Calculation of micropitting load capacity of cylindrical spur and helical gears -- Part 1: Introduction and basic principles

ISO/TR 15144-2:2014

Calculation of micropitting load capacity of cylindrical spur and helical gears -- Part 2: Examples of calculation for

micropitting

ISO/TR 18792:2008

Lubrication of industrial gear drives

ISO/TR 22849:2011

Design recommendations for bevel gears

ISO 23509:2006

Bevel and hypoid gear geometry

http://www.iso.org/iso/home/store/catalogue_tc/catalogue_detail.htm?csnumber=29603


39

9.3 ISO/TC 115

Title: Pumps

Secretariat: AFNOR (French National Standards Body) Secretary: Mme. Sara Mélique Chairperson: M. Robert Dodane until end 2016 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura MathewCreation date: 1964

The scope of ISO/TC 115 is the standardization in the field of pumps; including:

dimensions and technical specifications,

test methods and conditions of acceptance for rotodynamic and positive displacement pumps for

all liquids, including complete pumping installations,

installations and special applications, as well as rotodynamic mixers for waste water


25


5





Subcommittee Subcommittee title Irelands membership status

TC 115/SC 1 Dimensions and technical specifications of pumps -

TC 115/SC 2 Methods of measurement and testing -

TC 115/SC 3 Installation and special application -


ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries

ISO 13710:2004 Petroleum, petrochemical and natural gas industries -- Reciprocating positive displacement pumps

ISO/TR 17766:2005 Centrifugal pumps handling viscous liquids -- Performance corrections

ISO 21049:2004 Pumps -- Shaft sealing systems for centrifugal and rotary pumps


40

9.4 ISO/TC 118

Title: Compressors and pneumatic tools, machines and equipment

Secretariat: SIS Secretary: Ms Lena Fagervall Chairperson: Mrs. Jenny Buck (United Kingdom) until end 2016 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew Creation date: 1965

Scope of ISO/TC 118:

Standardization in the field of:

air compressors;

compressors for the process, petroleum, chemical and gas industry services;

pneumatic tools and machines;

compressed air purity specification and compressed air treatment equipment.

Excluded from the scope are pneumatic tool shanks and tool fitting dimensions, as they fall within the scope of ISO/TC 29 Small tools.


73






Subcommittee title Irelands membership status

TC 118/SC 1 Process compressors -

TC 118/SC 3 Pneumatic tools and machines -

TC 118/SC 4 Compressed air purity specification and compressed air treatment equipment

-

TC 118/SC 6 Air compressors and compressed air systems -

There are no Working Groups within ISO/TC 118.


ISO 5389:2005


41

Turbocompressors -- Performance test code

ISO 10439-1:2015 Petroleum, petrochemical and natural gas industries -- Axial and centrifugal compressors and expander-compressors -- Part 1: General requirements

ISO 10439-2:2015 Petroleum, petrochemical and natural gas industries -- Axial and centrifugal compressors and expander-compressors -- Part 2: Non-integrally geared centrifugal and axial compressors

ISO 10439-3:2015 Petroleum, petrochemical and natural gas industries -- Axial and centrifugal compressors and expander-compressors -- Part 3: Integrally geared centrifugal compressors

ISO 10439-4:2015 Petroleum, petrochemical and natural gas industries -- Axial and centrifugal compressors and expander-compressors -- Part 4: Expander-compressors

ISO 10440-1:2007 Petroleum, petrochemical and natural gas industries -- Rotary-type positive-displacement compressors -- Part 1: Process compressors

ISO 10440-2:2001 Petroleum and natural gas industries -- Rotary-type positive-displacement compressors -- Part 2: Packaged air compressors (oil-free)

ISO 10442:2002 Petroleum, chemical and gas service industries -- Packaged, integrally geared centrifugal air compressors

ISO 13631:2002 Petroleum and natural gas industries -- Packaged reciprocating gas compressors

9.5 ISO/TC 153

Title: Valves

Secretariat: AFNOR (French National Standards Body) Secretary: Mme Hélène Cros Chairperson: M. Alexandre Popa until end 2016 ISO Central Secretariat contact: Mme Hélène Cros Editorial Programme Manager(s): Ms Nicola Perou Creation date: 1971

The scope of work for ISO/TC 153 is the standardization in the field of industrial valves and steam traps. The standardization to include parameters covering interchangeability, valve mating details for actuator mounting, testing, marking, quality requirements, terminology and other relevant parameters.

Excluded from the scope are:

safety and relief valves and other pressure relief devices which are the responsibility of ISO/TC 185

Safety devices for protection against excessive pressure;

production valves for wellhead equipment and valves for cross country pipelines for the petroleum

and natural gas industries which are the responsibility of ISO/TC 67 Materials, equipment and

offshore structures for petroleum, petrochemical and natural gas industries;

valves forming the final control element used for industrial process control systems which are the

responsibility of IEC/TC 65 Industrial-process measurement, control and automation;

valves having an envelope predominantly made of plastics which are the responsibility of

ISO/TC 138 Plastics pipes, fittings and valves for the transport of fluids;


42

valves for sanitary use;

solenoids


24


11




Standards published by ISO/TC 153

ISO 5208:2015 Industrial valves -- Pressure testing of metallic valves

ISO 5209:1977 General purpose industrial valves – Marking

ISO 5210:1991 Industrial valves -- Multi-turn valve actuator attachments

ISO 5211:2001 Industrial valves -- Part-turn actuator attachments

ISO 5752:1982 Metal valves for use in flanged pipe systems -- Face-to-face and centre-to-face dimensions

ISO 6002:1992 Bolted bonnet steel gate valves

ISO 6552:1980 Automatic steam traps -- Definition of technical terms

ISO 6552:1980/Cor 1:2009

ISO 6553:1980 Automatic steam traps – Marking

ISO 6552:1980/Cor 1:2009

ISO 6553:1980 Automatic steam traps – Marking

ISO 6554:1980 Flanged automatic steam traps -- Face-to-face dimensions

ISO 6704:1982 Automatic steam traps – Classification

ISO 6948:1981 Automatic steam traps -- Production and performance characteristic tests

ISO 7121:2006 Steel ball valves for general-purpose industrial applications

ISO 7841:1988 Automatic steam traps -- Determination of steam loss -- Test methods

ISO 7842:1988


43

Automatic steam traps -- Determination of discharge capacity -- Test methods

ISO 10434:2004 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries

ISO 10497:2010 Testing of valves -- Fire type-testing requirements

ISO 10631:2013 Metallic butterfly valves for general purposes

ISO 12149:1999 Bolted bonnet steel globe valves for general-purpose applications

ISO 15761:2002 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries

ISO 15848-1:2015 Industrial valves -- Measurement, test and qualification procedures for fugitive emissions -- Part 1: Classification system and qualification procedures for type testing of valves

ISO 15848-2:2015 Industrial valves -- Measurement, test and qualification procedures for fugitive emissions -- Part 2: Production acceptance test of valves

ISO 17292:2015 Metal ball valves for petroleum, petrochemical and allied industries

ISO 28921-1:2013 Industrial valves -- Isolating valves for low-temperature applications -- Part 1: Design, manufacturing and production testing

ISO 28921-2:2015 Industrial valves -- Isolating valves for low-temperature applications -- Part 2: Type testing

9.6 ISO/TC 192 - Gas turbines

Secretariat: ANSI Secretary: Mr. Robin Proctor Chairperson: Mr. Benjamin Wiant (USA) until end 2016 ISO Central Secretariat contact: M. Charles-Pierre Bazin de Caix Editorial Programme Manager(s): Ms Nicola Perou Creation date: 1988

The scope of work of ISO/TC 192 is the standardization in the field of all aspects of gas turbine design, application, installation, operation and maintenance, including simple turbine cycles, combined cycle systems, definitions, procurement, acceptance, performance, environment (on the gas turbine itself and the external environment) and methods of test.

ISO/TC 192 is responsible for preparing horizontal standards for all types of gas turbines. Work on aero gas turbine engines shall be undertaken in liaison with those technique committees having the primary responsibility.

Note: ISO/TC 20 Aircraft and space vehicles, has the primary responsibility of preparing standards relative to the specific application of gas turbines to aerospace.


17


17


44

Participating countries: 15

Observing countries: 11


Standards published by ISO/TC 192

ISO 2314:2009 Gas turbines -- Acceptance tests

ISO 3977-1:1997 Gas turbines -- Procurement -- Part 1: General introduction and definitions

ISO 3977-2:1997 Gas turbines -- Procurement -- Part 2: Standard reference conditions and ratings

ISO 3977-3:2004 Gas turbines -- Procurement -- Part 3: Design requirements

ISO 3977-4:2002 Gas turbines -- Procurement -- Part 4: Fuels and environment

ISO 3977-5:2001 Gas turbines -- Procurement -- Part 5: Applications for petroleum and natural gas industries

ISO 3977-7:2002 Gas turbines -- Procurement -- Part 7: Technical information

ISO 3977-8:2002 Gas turbines -- Procurement -- Part 8: Inspection, testing, installation and commissioning

ISO 3977-9:1999 Gas turbines -- Procurement -- Part 9: Reliability, availability, maintainability and safety

ISO 10494:1993 Gas turbines and gas turbine sets -- Measurement of emitted airborne noise -- Engineering/survey method

ISO 11042-1:1996 Gas turbines -- Exhaust gas emission -- Part 1: Measurement and evaluation

ISO 11042-2:1996 Gas turbines -- Exhaust gas emission -- Part 2: Automated emission monitoring

ISO 11086:1996 Gas turbines – Vocabulary

ISO 19372:2015 Microturbines applications – Safety

ISO 19860:2005 Gas turbines -- Data acquisition and trend monitoring system requirements for gas turbine installations

ISO 21789:2009 Gas turbine applications -- Safety

ISO 26382:2010 Cogeneration systems -- Technical declarations for planning, evaluation and procurement


45

9.7 CEN/TC 12

Title: Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries

Status: Active Secretariat: NEN (Dutch National Standards Body) Secretary: Mr. J. Darkhorst([email protected])) Chairperson: CCMC PM: Mrs J. Frankowska

There are no Working Groups in this Technical Committee.

This Technical Committee mirrors the work of ISO/TC 67 at a European level and adopts, where appropriate, ISO Standards as European Standards.

Where modifications have been made to ISO Standards they have been published by the Technical Committee as separate European Standards.

All Standards published by this CEN Technical Committee are adopted as Irish Standards.

Standards published by CEN/TC 12

CEN ISO/TR 10400:2011 Petroleum and natural gas industries - Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing (ISO/TR 10400:2007)

CEN ISO/TR 13624-2:2013 Petroleum and natural gas industries - Drilling and production equipment - Part 2: Deepwater drilling riser methodologies, operations, and integrity technical report (ISO/TR 13624-2:2009)

CEN ISO/TR 13881:2011 Petroleum and natural gas industries - Classification and conformity assessment of products, processes and services (ISO/TR 13881:2000)

CEN ISO/TR 19905-2:2013 Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 2: Jack-ups commentary and detailed sample calculation (ISO/TR 19905-2:2012)

CEN ISO/TS 12747:2013 Petroleum and natural gas industries - Pipeline transportation systems - Recommended practice for pipeline life extension (ISO/TS 12747:2011)

CEN ISO/TS 17969:2015 Petroleum, petrochemical and natural gas industries - Guidelines on competency for personnel (ISO/TS 17969:2015)

CEN ISO/TS 27469:2011 Petroleum, petrochemical and natural gas industries - Method of test for fire dampers (ISO/TS 27469:2010)

CEN ISO/TS 29001:2011 Petroleum, petrochemical and natural gas industries - Sector-specific quality management systems - Requirements for product and service supply organizations (ISO/TS 29001:2010)

CEN/TR 14549:2004 Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment Directive

EN 13942:2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified)

EN 13942:2009/AC:2009


46

EN 14161:2011+A1:2015 Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2009 modified)

EN 14163:2001 Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000 modified)

EN 14163:2001/AC:2006

EN 14870-1:2011 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2009 modified)

EN 14870-2:2004 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings (ISO 15590-2:2003 modified)

EN 14870-3:2006 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004, modified)

EN ISO 10405:2006 Petroleum and natural gas industries - Care and use of casing and tubing (ISO 10405:2006)

EN ISO 10407-2:2008 Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Inspection and classification of used drill stem elements (ISO 10407-2:2008)

EN ISO 10407-2:2008/AC:2009

EN ISO 10414-1:2008 Petroleum and natural gas industries - Field testing of drilling fluids - Part 1: Water-based fluids (ISO 10414-1:2008)

EN ISO 10414-2:2011 Petroleum and natural gas industries - Field testing of drilling fluids - Part 2: Oil-based fluids (ISO 10414-2:2011)

EN ISO 10416:2009 Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008)

EN ISO 10417:2004 Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress (ISO 10417:2004)

EN ISO 10418:2003 Petroleum and natural gas industries - Offshore production installations - Basic surface process safety systems (ISO 10418:2003)

EN ISO 10418:2003/AC:2009

EN ISO 10423:2009 Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO 10423:2009)

EN ISO 10424-1:2004 Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (ISO 10424-1:2004)

EN ISO 10424-2:2007 Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Threading and gauging of rotary shouldered thread connections (ISO 10424-2:2007)

EN ISO 10426-1:2009 Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification (ISO 10426-1:2009)

EN ISO 10426-1:2009/AC:2010

EN ISO 10426-2:2003+A1:2005 Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well


47

cements - Amendment 1: Water-wetting capability testing (ISO 10426-2:2003+A1:2005)

EN ISO 10426-2:2003/AC:2007

EN ISO 10426-3:2004 Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations (ISO 10426-3:2003)

EN ISO 10426-4:2004 Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure (ISO 10426-4:2004)

EN ISO 10426-5:2005 Petroleum and natural gas industries - Cements and materials for well cementing - Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure (ISO 10426-5:2004)

EN ISO 10426-6:2008 Petroleum and natural gas industries - Cements and materials for well cementing - Part 6: Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008)

EN ISO 10427-1:2001 Petroleum and natural gas industries - Casing centralizers - Part 1: Bow-spring casing centralizers (ISO 10427-1:2001)

EN ISO 10427-2:2004 Petroleum and natural gas industries - Equipment for well cementing - Part 2: Centralizer placement and stop-collar testing (ISO 10427-2:2004)

EN ISO 10427-3:2004 Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float equipment (ISO 10427-3:2003)

EN ISO 10432:2004 Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment (ISO 10432:2004)

EN ISO 10437:2003 Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications (ISO 10437:2003)

EN ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements (ISO 10438-1:2007)

EN ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems (ISO 10438-2:2007)

EN ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2007)

EN ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 4: Self-acting gas seal support systems (ISO 10438-4:2007)

EN ISO 10439-1:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 1: General requirements (ISO 10439-1:2015)

EN ISO 10439-2:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 2: Non-integrally geared centrifugal and axial compressors (ISO 10439-2:2015)

EN ISO 10439-3:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 3: Integrally geared centrifugal compressors (ISO 10439-3:2015)

EN ISO 10439-4:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-


48

compressors - Part 4: Expander-compressors(ISO 10439-4:2015)

EN ISO 10440-1:2007 Petroleum, petrochemical and natural gas industries - Rotary-type positive-displacement compressors - Part 1: Process compressors (ISO 10440-1:2007)

EN ISO 10440-2:2001 Petroleum and natural gas industries - Rotary-type positive-displacement compressors - Part 2: Packaged air compressors (oil-free) (ISO 10440-2:2001)

EN ISO 10441:2007 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007)

EN ISO 10442:2002 Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002)

EN ISO 11960:2014 Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells (ISO 11960:2014)

EN ISO 11961:2008 Petroleum and natural gas industries - Steel drill pipe (ISO 11961:2008)

EN ISO 11961:2008/AC:2009

EN ISO 12211:2012 Petroleum, petrochemical and natural gas industries - Spiral plate heat exchangers (ISO 12211:2012)

EN ISO 12212:2012 Petroleum, petrochemical and natural gas industries - Hairpin-type heat exchangers (ISO 12212:2012)

EN ISO 12736:2014 Petroleum and natural gas industries - Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures (ISO 12736:2014)

EN ISO 13085:2014 Petroleum and natural gas industries - Aluminium alloy pipe for use as tubing for wells (ISO 13085:2014)

EN ISO 13354:2014 Petroleum and natural gas industries - Drilling and production equipment - Shallow gas diverter equipment (ISO 13354:2014)

EN ISO 13500:2008+A1:2010 Petroleum and natural gas industries - Drilling fluid materials - Specifications and tests - Amendment 1: Barite 4,1 (ISO 13500:2008+AMD 1:2010)

EN ISO 13501:2011 Petroleum and natural gas industries - Drilling fluids - Processing equipment evaluation (ISO 13501:2011)

EN ISO 13503-1:2011 Petroleum and natural gas industries - Completion fluids and materials - Part 1: Measurement of viscous properties of completion fluids (ISO 13503-1:2011)

EN ISO 13503-2:2006+A1:2009 Petroleum and natural gas industries - Completion fluids and materials - Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations - Amendment 1: Addition of Annex B: Proppand specification (ISO 13503-2:2006+Amd 1:2009)

EN ISO 13503-3:2005 Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines (ISO 13503-3:2005)

EN ISO 13503-3:2005/AC:2007

EN ISO 13503-4:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 4: Procedure for measuring stimulation and gravel-pack fluid leakoff under static conditions (ISO 13503-4:2006)

EN ISO 13503-5:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 5: Procedures for measuring the


49

long-term conductivity of proppants (ISO 13503-5:2006)

EN ISO 13503-6:2014 Petroleum and natural gas industries - Completion fluides and materials - Part 6: Procedure for measuring leakoff of completion fluids under dynamic conditions (ISO 13503-6:2014)

EN ISO 13533:2001 Petroleum and natural gas industries - Drilling and production equipment - Drill-through equipment (ISO 13533:2001)

EN ISO 13533:2001/AC:2006

EN ISO 13534:2000 Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and remanufacture of hoisting equipment (ISO 13534:2000)

EN ISO 13535:2000 Petroleum and natural gas industries - Drilling and production equipment - Hoisting equipment (ISO 13535:2000)

EN ISO 13624-1:2009 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Design and operation of marine drilling riser equipment (ISO 13624-1:2009)

EN ISO 13625:2002 Petroleum and natural gas industries - Drilling and production equipment - Marine drilling riser couplings (ISO 13625:2002)

EN ISO 13626:2004 Petroleum and natural gas industries - Drilling and production equipment - Drilling and well-servicing structures (ISO 13626:2003)

EN ISO 13628-1:2005+A1:2010 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations - Amendment 1: Revised Clause 6 (ISO 13628-1:2005+Amd 1:2010)

EN ISO 13628-10:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe (ISO 13628-10:2006)

EN ISO 13628-11:2008 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe systems for subsea and marine applications (ISO 13628-11:2007)

EN ISO 13628-11:2008/AC:2009

EN ISO 13628-15:2011 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 15: Subsea structures and manifolds (ISO 13628-15:2011)

EN ISO 13628-2:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible pipe systems for subsea and marine applications (ISO 13628-2:2006)

EN ISO 13628-2:2006/AC:2009

EN ISO 13628-3:2000 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 3: Through flowline (TFL) systems (ISO 13628-3:2000)

EN ISO 13628-4:2010 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 4: Subsea wellhead and tree equipment (ISO 13628-4:2010)

EN ISO 13628-4:2010/AC:2011

EN ISO 13628-5:2009 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals (ISO 13628-5:2009)


50

EN ISO 13628-6:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 6: Subsea production control systems (ISO 13628-6:2006)

EN ISO 13628-7:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 7: Completion/workover riser systems (ISO 13628-7:2005)

EN ISO 13628-8:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems (ISO 13628-8:2002)

EN ISO 13628-9:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 9: Remotely Operated Tool (ROT) intervention systems (ISO 13628-9:2000)

EN ISO 13631:2002 Petroleum and natural gas industries - Packaged reciprocating gas compressors (ISO 13631:2002)

EN ISO 13678:2012 Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements (ISO 13678:2010)

EN ISO 13679:2006 Petroleum and natural gas industries - Procedures for testing casing and tubing connections (ISO 13679:2002)

EN ISO 13680:2010 Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)

EN ISO 13691:2002 Petroleum and natural gas industries - High-speed special-purpose gear units (ISO 13691:2001)

EN ISO 13702:2015 Petroleum and natural gas industries - Control and mitigation of fires and explosions on offshore production installations - Requirements and guidelines (ISO 13702:2015)

EN ISO 13703:2000 Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000)

EN ISO 13703:2000/AC:2007

EN ISO 13704:2007 Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries (ISO 13704:2007)

EN ISO 13704:2007/AC:2009

EN ISO 13705:2012 Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service (ISO 13705:2012)

EN ISO 13706:2011 Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2011)

EN ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009)

EN ISO 13710:2004 Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps (ISO 13710:2004)

EN ISO 14224:2006 Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment (ISO 14224:2006)

EN ISO 14310:2008 Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2008)


51

EN ISO 14691:2008 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-purpose applications (ISO 14691:2008)

EN ISO 14692-1:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2002)

EN ISO 14692-2:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002)

EN ISO 14692-2:2002/AC:2006

EN ISO 14692-3:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2002)

EN ISO 14692-3:2002/AC:2006

EN ISO 14692-4:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2002)

EN ISO 14692-4:2002/AC:2007

EN ISO 14693:2003 Petroleum and natural gas industries - Drilling and well-servicing equipment (ISO 14693:2003)

EN ISO 14723:2009 Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2009)

EN ISO 14998:2013 Petroleum and natural gas industries - Downhole equipment - Completion accessories (ISO 14998:2013)

EN ISO 15136-1:2009 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps (ISO 15136-1:2009)

EN ISO 15136-2:2006 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems (ISO 15136-2:2006)

EN ISO 15138:2007 Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning (ISO 15138:2007)

EN ISO 15156-1:2015 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials (ISO 15156-1:2015)

EN ISO 15156-2:2015 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons (ISO 15156-2:2015)

EN ISO 15156-3:2015 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2015)

EN ISO 15463:2003 Petroleum and natural gas industries - Field inspection of new casing, tubing and plain-end drill pipe (ISO 15463:2003)

EN ISO 15463:2003/AC:2009

EN ISO 15544:2010 Petroleum and natural gas industries - Offshore production installations - Requirements and guidelines for emergency response (ISO 15544:2000, including Amd 1:2009)


52

EN ISO 15546:2011 Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2011)

EN ISO 15547-1:2005 Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat exchangers (ISO 15547-1:2005)

EN ISO 15547-2:2005 Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin heat exchangers (ISO 15547-2:2005)

EN ISO 15551-1:2015 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Electric submersible pump systems for artificial lift (ISO 15551-1:2015)

EN ISO 15663-1:2006 Petroleum and natural gas industries - Life cycle costing - Part 1: Methodology (ISO 15663-1:2000)

EN ISO 15761:2002 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries (ISO 15761:2002)

EN ISO 16070:2005 Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005)

EN ISO 16708:2006 Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods (ISO 16708:2006)

EN ISO 16812:2007 Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers (ISO 16812:2007)

EN ISO 16961:2015 Petroleum, petrochemical and natural gas industries - Internal coating and lining of steel storage tanks (ISO 16961:2015)

EN ISO 17078-1:2004+A1:2010 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels - Amendment 1 (ISO 17078-1:2004+Amd 1:2010)

EN ISO 17078-2:2007 Petroleum and natural gas industries - Drilling and production equipment - Part 2: Flow-control devices for side-pocket mandrels (ISO 17078-2:2007)

EN ISO 17078-2:2007/AC:2009

EN ISO 17078-3:2009 Petroleum and natural gas industries - Drilling and production equipment - Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels (ISO 17078-3:2009)

EN ISO 17078-4:2010 Petroleum and natural gas industries - Drilling and production equipment - Part 4: Practices for side-pocket mandrels and related equipment (ISO 17078-4:2010)

EN ISO 17776:2002 Petroleum and natural gas industries - Offshore production installations - Guidelines on tools and techniques for hazard identification and risk assessment (ISO 17776:2000)

EN ISO 17824:2014 Petroleum and natural gas industries - Downhole equipment - Sand screens (ISO 17824:2009)

EN ISO 17945:2015 Petroleum, petrochemical and natural gas industries - Metallic materials resistant to sulfide stress cracking in corrosive petroleum refining environments (ISO 17945:2015)

EN ISO 19900:2013 Petroleum and natural gas industries - General requirements for offshore structures (ISO 19900:2013)

EN ISO 19901-1:2015 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design


53

and operating considerations (ISO 19901-1:2015)

EN ISO 19901-2:2004 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 2: Seismic design procedures and criteria (ISO 19901-2:2004)

EN ISO 19901-3:2014 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure (ISO 19901-3:2014)

EN ISO 19901-4:2003 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 4: Geotechnical and foundation design considerations (ISO 19901-4:2003)

EN ISO 19901-5:2003 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 5: Weight control during engineering and construction (ISO 19901-5:2003)

EN ISO 19901-6:2009 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 6: Marine operations (ISO 19901-6:2009)

EN ISO 19901-6:2009/AC:2011

EN ISO 19901-7:2013 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units (ISO 19901-7:2013)

EN ISO 19901-8:2015 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 8: Marine soil investigations (ISO 19901-8:2014)

EN ISO 19902:2007+A1:2013 Petroleum and natural gas industries - Fixed steel offshore structures (ISO 19902:2007+Amd 1:2013)

EN ISO 19903:2006 Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006)

EN ISO 19904-1:2006 Petroleum and natural gas industries - Floating offshore structures - Part 1: Monohulls, semi-submersibles and spars (ISO 19904-1:2006)

EN ISO 19905-1:2012 Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 1: Jack-ups (ISO 19905-1:2012)

EN ISO 19906:2010 Petroleum and natural gas industries - Arctic offshore structures (ISO 19906:2010)

EN ISO 20312:2011 Petroleum and natural gas industries - Design and operating limits of drill strings with aluminium alloy components (ISO 20312:2011)

EN ISO 20815:2010 Petroleum, petrochemical and natural gas industries - Production assurance and reliability management (ISO 20815:2008, Corrected version 2009-06-15)

EN ISO 21049:2004 Pumps - Shaft sealing systems for centrifugal and rotary pumps (ISO 21049:2004)

EN ISO 21329:2004 Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors (ISO 21329:2004)

EN ISO 21457:2010 Petroleum, petrochemical and natural gas industries - Materials selection and corrosion control for oil and gas production systems (ISO 21457:2010)

EN ISO 23251:2007+A1:2008 Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems -


54

Amendment 1 (ISO 23251:2007+Amd 1:2008)

EN ISO 23251:2007/AC:2008

EN ISO 23936-1:2009 Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 1: Thermoplastics (ISO 23936-1:2009)

EN ISO 23936-2:2011 Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 2: Elastomers (ISO 23936-2:2011)

EN ISO 24817:2015 Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO 24817:2015)

EN ISO 25457:2008 Petroleum, petrochemical and natural gas industries - Flare details for general refinery and petrochemical service (ISO 25457:2008)

EN ISO 27509:2012 Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2012)

EN ISO 27509:2012/AC:2013

EN ISO 27627:2014 Petroleum and natural gas industries - Aluminium alloy drill pipe thread connection gauging (ISO 27627:2014)

EN ISO 28300:2008 Petroleum, petrochemical and natural gas industries - Venting of atmospheric and low-pressure storage tanks (ISO 28300:2008)

EN ISO 28300:2008/AC:2009

EN ISO 28781:2010 Petroleum and natural gas industries - Drilling and production equipment - Subsurface barrier valves and related equipment (ISO 28781:2010)

EN ISO 3977-5:2003 Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries (ISO 3977-5:2001)

EN ISO 3977-5:2003/AC:2007


55

9.8 CEN/TC 69

Title: Industrial valves

Status: Active Secretariat: AFNOR (French National Standards Body) Secretary: Ms H. Cros mailto... ( [email protected] ) Chairperson: Mr P. Vinzio (FR) CCMC PM: Mr T. Legrand mailto... ( [email protected] )

There are 18 Working Groups in this Technical Committee of which 6 are active.

This Technical Committee mirrors the relevant work of ISO/TC 138, ISO/TC 153 and ISO/TC 185 at a European level and adopts, where appropriate, ISO Standards as European Standards.

The scope of work covered by the Technical Committee includes the standardization of valves for all industrial applications and for all types of fluids, including steam traps; valve actuator interface; safety devices against excessive pressure (safety valves and bursting disks); control valves (excluding the actuator element and their interface); but excluding sanitary valves as defined by CEN/TC 164/WG 8.

Where modifications have been made to ISO Standards they have been published by the Technical Committee as separate European Standards.

All Standards published by this CEN Technical Committee are adopted as Irish Standards.

Standards published by CEN/TC 69

EN 1171:2015 Industrial valves - Cast iron gate valves

EN 12266-1:2012 Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements

EN 12266-2:2012 Industrial valves - Testing of metallic valves - Part 2: Tests, test procedures and acceptance criteria - Supplementary requirements

EN 12288:2010 Industrial valves - Copper alloy gate valves

EN 12334:2001 Industrial valves - Cast iron check valves

EN 12351:2010 Industrial valves - Protective caps for valves with flanged connections

EN 12516-1:2014 Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells

EN 12516-2:2014 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells

EN 12516-3:2002 Valves - Shell design strength - Part 3: Experimental method

EN 12516-4:2014 Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel


56

EN 12567:2000 Industrial valves - Isolating valves for LNG - Specification for suitability and appropriate verification tests

EN 12569:1999 Industrial valves - Valves for chemical and petrochemical process industry - Requirements and tests

EN 12570:2000 Industrial valves - Method for sizing the operating element

EN 12627:1999 Industrial valves - Butt welding ends for steel valves

EN 1267:2012 Industrial valves - Test of flow resistance using water as test fluid

EN 12760:1999 Valves - Socket welding ends for steel valves

EN 12982:2009 Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves

EN 13397:2001 Industrial valves - Diaphragm valves made of metallic materials

EN 1349:2009 Industrial process control valves

EN 13547:2013 Industrial valves - Copper alloy ball valves

EN 13709:2010 Industrial valves - Steel globe and globe stop and check valves

EN 13774:2013 Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar - Performance requirements

EN 13789:2010 Industrial valves - Cast iron globe valves

EN 14141:2013 Valves for natural gas transportation in pipelines - Performance requirements and tests

EN 14341:2006 Industrial valves - Steel check valves

EN 1503-4:2002 Valves - Materials for bodies, bonnets and covers - Part 4: Copper alloys specified in European Standards

EN 15081:2007 Industrial valves - Mounting kits for part-turn valve actuator attachment

EN 15714-1:2009 Industrial valves - Actuators - Part 1: Terminology and definitions

EN 15714-2:2009 Industrial valves - Actuators - Part 2: Electric actuators for industrial valves - Basic requirements

EN 15714-3:2009 Industrial valves - Actuators - Part 3: Pneumatic part-turn actuators for industrial valves - Basic requirements

EN 15714-4:2009 Industrial valves - Actuators - Part 4: Hydraulic part-turn actuators for industrial valves - Basic requirements

EN 16722:2015 Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends

EN 19:2002 Industrial valves - Marking of metallic valves

EN 1983:2013


57

Industrial valves - Steel ball valves

EN 1984:2010 Industrial valves - Steel gate valves

EN 26553:1991 Automatic steam traps - Marking (ISO 6553:1980)

EN 26554:1991 Flanged automatic steam traps - Face-to-face dimensions (ISO 6554:1980)

EN 26704:1991 Automatic steam traps - Classification (ISO 6704:1982)

EN 26948:1991 Automatic steam traps - Production and performance characteristic tests (ISO 6948:1981)

EN 27841:1991 Automatic steam traps - Determination of steam loss - Test methods (ISO 7841:1988)

EN 27842:1991 Automatic steam traps - Determination of discharge capacity - Test methods (ISO 7842:1988)

EN 28233:1990 Thermoplastics valves - Torque - Test method (ISO 8233:1988)

EN 28659:1990 Thermoplastics valves - Fatigue strength - Test method (ISO 8659:1989)

EN 558:2008+A1:2011 Industrial valves - Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems - PN and Class designated valves

EN 593:2009+A1:2011 Industrial valves - Metallic butterfly valves

EN 736-1:1995 Valves - Terminology - Part 1: Definition of types of valves

EN 736-2:1997 Valves - Terminology - Part 2: Definition of components of valves

EN 736-3:2008 Valves - Terminology - Part 3: Definition of terms

EN ISO 10434:2004 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries (ISO 10434:2004)

EN ISO 10497:2010 Testing of valves - Fire type-testing requirements (ISO 10497:2010)

EN ISO 15848-1:2015 Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves (ISO 15848-1:2015)

EN ISO 15848-2:2015 Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 2: Production acceptance test of valves (ISO 15848-2:2015)

EN ISO 17292:2015 Metal ball valves for petroleum, petrochemical and allied industries (ISO 17292:2015)

EN ISO 4126-1:2013 Safety devices for protection against excessive pressure - Part 1: Safety valves (ISO 4126-1:2013)

EN ISO 4126-2:2003 Safety devices for protection against excessive pressure - Part 2: Bursting disc safety devices (ISO 4126-2:2003)


58

EN ISO 4126-3:2006 Safety devices for protection against excessive pressure - Part 3: Safety valves and bursting disc safety devices in combination (ISO 4126-3:2006)

EN ISO 4126-4:2013 Safety devices for protection against excessive pressure - Part 4: Pilot-operated safety valves (ISO 4126-4:2013)

EN ISO 4126-5:2013 Safety devices for protection against excessive pressure - Part 5: Controlled safety pressure relief systems (CSPRS) (ISO 4126-5:2013)

EN ISO 4126-6:2014 Safety devices for protection against excessive pressure - Part 6: Application, selection and installation of bursting disc safety devices (ISO 4126-6:2014)

EN ISO 4126-7:2013 Safety devices for protection against excessive pressure - Part 7: Common data (ISO 4126-7:2013)

EN ISO 5210:1996 Industrial valves - Multi-turn valve actuator attachments (ISO 5210:1991)

EN ISO 5211:2001 Industrial valves - Part-turn actuator attachments (ISO 5211:2001)


59

Standards

Where do I get standards?All standards can be purchased in either hard or electronic form, visit www.standards.ie

A preview, scope and table of contents is available online, free-of charge, for many standards from NSAI. NSAI publish all EN and many ISO and IEC standards as equivalent Irish Standards.

Your Standards, Your SayTake an active role in how Standards can meet business needs.

NSAI has improved the opportunities for all interested parties to engage in the national standardization process. Your Standards, Your Say is where new and changing standards can be viewed and commented on, free of charge.

Visit NSAI Your Standards, Your Say at www.nsainep.ie

NSAI is the National Standards Body in Ireland.

Contact us

NSAI, 1 Swift Square, Northwood,

Santry, Dublin 9, Ireland. D09 A0E9

T +353 1 807 3800

E [email protected]

W www.nsai.ie

Follow us

Twitter @NSAI_Standards

Youtube www.youtube.com/user/NSAImedia

LinkedIn www.linkedin.com/company/national-standards-authority-of-ireland

Documents

Petroleum Exploration and Extraction Technical Standards ... · Petroleum Exploration and Extraction Technical Standards Committee 6 ISO/TC 185, Safety devices for protection against