PL 008-748June 2001

Parts List

9100A and 9200A SeriesFlanged Magnetic Flowtubes

9100A Serieswith Neoprene or EPDM Liners

1 to 78 in (25 to 2000 mm) Nominal Flowtube SizesStyle A

and

9200A Serieswith Neoprene, EPDM, Linatex, Ebonite, or ptfe Liners 8 to 48 in (200 to 1200 mm) Nominal Flowtube Sizes

Style A

*Parts preceded by an asterisk are recommended spare parts.Give instrument Model Number and Style when ordering.

See Recommended Spare Parts Summary section for quantities.

TO ORDER PARTS, CALL FOXBORO AT 1-888-FOXBORO (1-888-369-2676).

®

PL 008-748Page 2

(a) See “End Connection” selections further in Code to determine ANSI, AWWA, and BS (DIN) flanges applicable to each flowtube size.

MODEL CODE

9100A Series Magnetic FlowtubesNominal Flowtube Size (a) Model

DN Flange Size Inch Flange Size25 mm 1 in 9101A40 mm 1 1/2 in 911HA50 mm 2 in 9102A65 mm 2 1/2 in 912HA

80 mm 3 in 9103A100 mm 4 in 9104A125 mm 5 in 9105A150 mm 6 in 9106A200 mm 8 in 9108A

250 mm 10 in 9110A300 mm 12 in 9112A350 mm 14 in 9114A400 mm 16 in 9116A450 mm 18 in 9118A

500 mm 20 in 9120A600 mm 24 in 9124A700 mm 28 in 9128A

– 30 in 9130A800 mm 32 in 9132A

900 mm 36 in 9136A1000 mm 40 in 9140A

– 42 in 9142A– 44 in 9144A

1200 mm 48 in 9148A

1400 mm 54 in 9154A– 60 in 9160A

1600 mm 66 in 9166A1800 mm 72 in 9172A2000 mm 78 in 9178A

Tube ConstructionAISI Type 304 Stainless Steel Tube (304 ss) –SI

End ConnectionsANSI Class 150, Carbon Steel Flange - 1 to 24 in Line Sizes BAAWWA C-207, Class D, Carbon Steel Flange - 28 to 78 in Line Sizes WBPN 6, BS 4504 (DIN 2501), Carbon Steel Flange - 1400 to 2000 mm Line Sizes ZZPN 10, BS 4504 (DIN 2501), Carbon Steel Flange - 200 to 2000 mm Line Sizes ZDPN 16, BS 4504 (DIN 2501), Carbon Steel Flange - 65 to 2000 mm Line Sizes ZEPN 40, BS 4504 (DIN 2501), Carbon Steel Flange - 25 to 50 mm Line Sizes ZG

PL 008-748Page 3

MODEL CODE (Cont.)

9100A Series Magnetic Flowtubes (Cont.)

Liner MaterialNeoprene -NEPDM (an Ethylene Propylene Terpolymer) -E

ElectrodesAISI Type 316Ti Stainless Steel (316Ti ss) - Fluid Reference Electrode Included S

Coil DrivePulsed dc J

Housing Construction/Transmitter MountingCoated Carbon Steel Housing with Aluminum Terminal Box

– Terminal Box has 1/2 inch Conduit Threads– Remote Mounted Transmitter

-G

Coated Carbon Steel Housing with Polyamide Terminal Box– Terminal Box has PG13.5 Conduit Threads with Cable Glands– Remote Mounted Transmitter

-P

Electrical Safety (Also see Electrical Safety Specifications section)CSA, General Purpose (Ordinary) Locations KFM, General Purpose (Ordinary) Locations MNo Approvals - Flowtube Marked with “CE” Logo Z

Example: 9116A-SIBA-ESJ-PM

PL 008-748Page 4

MODEL CODE

9200A Series Magnetic FlowtubesNominal Flowtube Size (a) Model

DN Flange Size Inch Flange Size200 mm 8 in 9208A250 mm 10 in 9210A300 mm 12 in 9212A350 mm 14 in 9214A400 mm 16 in 9216A

450 mm 18 in 9218A500 mm 20 in 9220A600 mm 24 in 9224A700 mm 28 in 9228A

– 30 in 9230A

800 mm 32 in 9232A900 mm 36 in 9236A1000 mm 40 in 9240A

– 42 in 9242A– 44 in 9244A

1200 mm 48 in 9248A

Tube ConstructionAISI Type 304 Stainless Steel Tube (304 ss) –SI

End ConnectionsANSI Class 150, Carbon Steel Flange - 8 to 24 in Line Sizes BAANSI Class 150, Stainless Steel Flange - 8 to 24 in Line Sizes BBANSI Class 300, Carbon Steel Flange - 8 to 24 in Line Sizes BDAWWA C-207, Class D Carbon Steel Flange - 28 to 48 in Line Sizes WBAS 2129, Table E, Carbon Steel Flange - 200 to 1200 mm Line Sizes YABS 4505 (DIN 2501), PN 6, Carbon Steel Flange - 200 to 1200 mm Line Sizes ZZBS 4505 (DIN 2501), PN 6, Stainless Steel Flange - 200 to 600 mm Line Sizes ZKBS 4505 (DIN 2501), PN 10, Carbon Steel Flange - 200 to 1200 mm Line Sizes ZDBS 4505 (DIN 2501), PN 10, Stainless Steel Flange - 200 to 600 mm Line Sizes ZLBS 4505 (DIN 2501), PN 16, Carbon Steel Flange - 200 to 1200 mm Line Sizes ZEBS 4505 (DIN 2501), PN 16, Stainless Steel Flange - 200 to 600 mm Line Sizes ZMBS 4505 (DIN 2501), PN 25, Carbon Steel Flange - 200 to 600 mm Line Sizes ZFBS 4505 (DIN 2501), PN 40, Carbon Steel Flange - 200 to 600 mm Line Sizes ZG

Liner MaterialNeoprene -NEPDM (an Ethylene Propylene Terpolymer) -Eptfe High Temperature - 180°C (350°F) Limit; Includes Two Type “E” Liner Protection Rings -Hptfe - 120°C (250°F) Limit -TEbonite -BLinatex -L

(a) See “End Connection” selections further in Code for ANSI, AWWA, AS, and DIN flanges applicable to each flowtube size.

PL 008-748Page 5

(a) Fluid reference electrode included, except for flowtubes with a ptfe liner.

Electrodes(a)AISI Type 316Ti Stainless Steel (316Ti ss) S316 ss, Ceramic Coated GHastelloy C-276 HPlatinum-Iridium PTitanium TMonel MTantalum B

Coil DrivePulsed dc J

Housing Construction/Transmitter MountingCoated Carbon Steel Housing with Aluminum Terminal Box

– Terminal Box has 1/2 inch Conduit Threads– Remote Mounted Transmitter

-G

Coated Carbon Steel Housing with Polyamide Terminal Box– Terminal Box has PG13.5 Conduit Threads with Cable Glands– Remote Mounted Transmitter

-P

Electrical Safety (Also see Electrical Safety Specifications section)CSA, General Purpose (Ordinary) Locations KCSA, Class I, Division 2 LFM, General Purpose (Ordinary) Locations MFM, Nonincendive, Class I, Division 2 NCENELEC, EEx e ia, IIC SNo Approvals or Certifications - Flowtube Marked with ”CE” Logo Z

Example: 9216A-SIBA-NSJ-PM

MODEL CODE (Cont.)

9200A Series Magnetic Flowtubes (Cont.)

PL 008-748Page 6

FIGURE 19100A or 9200A Flanged Magnetic Flowtube Assembly

with Plastic Terminal Box Assembly

NOTE1. The flowtube itself has no replaceable parts and must be ordered as a complete assembly with the terminal box assembled to it. The Model Number of the complete assembly can be taken from the data plate, or created using the Model Codes shown in this Parts List.2. Type “E” 316 ss rings for liner protection and grounding are provided with each flowtube lined with high temperature ptfe. Refer to Figure 4 and Table 2.

Item Part No. Qty. Part Name

1 083B0070 1 Base Assembly, Plastic (Polyamide) Terminal Box Includes Terminals, but not Cover or Gasket

*2 083B0069 1 Terminal Box Cover, Plastic (Polyamide) - Includes Gasket3 083G0228 2 Cable Gland, PG 13.5; Black Polyamide

TERMINAL BOXMOUNTING PLATE,REFERENCE

FLOWTUBEASSEMBLY,SEE NOTEBELOW.

FOUR SCREWS ON SQUARE HOLE PATTERN ALLOWTERMINAL BOX TOBE ROTATED 90˚ IN EITHER DIRECTION

PG13.5 THREADS FOR CONDUIT, CABLE GLANDS, OR NEMA 4X METAL PLUGS

2

13

TOP INTERNALVIEW

TERMINAL BOXBASE ASSEMBLYGASKET(REFERENCE)

CABLE GLANDS(TWO PLACES)

PLASTIC CAP PLUGS FORSHIPMENT ONLY. REMOVEAND REPLACE UNUSEDHOLES WITH NEMA 4X PLUGS

NUTS, PART OF ITEM 1

CAPTIVESCREWS,PART OFITEM 1

GASKET, PARTOF ITEM 2

PL 008-748Page 7

FIGURE 29100A or 9200A Flanged Magnetic Flowtube Assembly

with Aluminum Terminal Box Assembly

NOTEThe flowtube itself has no replaceable parts and must be ordered as a complete assembly with the terminal box assembled to it. The Model Number of the complete assembly can be taken from the data plate, or created using the Model Codes shown in this Parts List.

Item Part No. Qty. Part Name

1 D0164XB 1 Base, Aluminum Terminal BoxExcludes Terminal Blocks, Cover, and Gasket

2 D0164XQ 1 Terminal Box Cover, Aluminum*3 D0164XG 1 Gasket, Terminal Box Cover4 X7000BA 4 Screw, Captive; Cross-Recessed Panhead; ss, 0.194-32 x 0.750

FLOWTUBEASSEMBLY,SEE NOTEBELOW

1

3

2

4

FOUR SCREWS ON SQUARE HOLE PATTERN ALLOW TERMINAL BOX TO BE ROTATED 90˚ IN EITHER DIRECTION

TWO CABLE ENTRY HOLES, 0.500-14 NPT THREADS. FOR CONDUIT OR CABLE GLANDS.REMOVE AND DISCARD PLASTIC CAP PLUGS PRIOR TO INSTALLATION. UNUSED HOLE, IF APPLICABLE MUST BE CLOSED WITH NEMA 4X PLUGS.

TOP INTERNALVIEW

1

TERMINAL BOXBASE ASSEMBLYGASKET(REFERENCE)

TERMINAL BLOCK,TWO PLACES

PL 008-748Page 8

FIGURE 3Optional Type “C” Liner Protection (Grounding) Rings

with Flowtubes having Neoprene, EPDM, Linatex, or Ebonite Liners

Table 1. Part Numbers for Type “C” 304 ss Liner Protection Rings(a)

Flowtube Size Flange Type with Type “C” 304 ss Liner Protection Ring - Part Numbers

DNFlange

Size

InchFlange

SizeDINPN 6

DINPN 10

DINPN 16

DINPN 25

DINPN 40

ANSICl. 150

ANSICl. 300

AWWAClass D

AS 2129Tbl. E

25 mm 1 in – – – – 083N8361 083N8361 – – –40 mm 1 1/2 in – – – – 083N8362 083N8362 – – –50 mm 2 in – – – – 083N8344 083N8344 – – –65 mm 2 1/2 in – – 083N8345 – – 083N8345 – – –80 mm 3 in – – 083N8347 – – 083N8347 – – –100 mm 4 in – – 083N8025 – – 083N8025 – – –125 mm 5 in – – 083N8071 – – 083N8071 – – –150 mm 6 in – – 083N8008 – – 083N8008 – – –200 mm 8 in 083N8074 083N8011 083N8011 083N8011 083N8075 083N8011 083N8076 – 083N8011250 mm 10 in 083N8078 083N8013 083N8013 083N8013 083N8073 083N8013 083N8079 – 083N8013300 mm 12 in 083N8080 083N8012 083N8012 083N8081 083N8082 083N8012 083N8082 – 083N8012350 mm 14 in 083N8083 083N8039 083N8039 083N8084 083N8085 083N8039 083N8085 – 083N8039400 mm 16 in 083N8099 083N8100 083N8100 083N8101 083N8102 083N8100 083N8102 – 083N8100450 mm 18 in 083N8103 083N8103 083N8104 083N8104 083N8105 083N8104 083N8106 – 083N8104500 mm 20 in 083N8107 083N8107 083N8108 083N8108 083N8109 083N8107 083N8110 – 083N8108600 mm 24 in 083N8111 083N8111 083N8112 083N8112 – 083N8113 083N8114 – 083N8113700 mm 28 in 083N8300 083N8294 083N8294 – – – – (b) (b)

– 30 in – – – – – – – (b) (b)800 mm 32 in 083N8303 083N8304 083N8304 – – – – (b) (b)900 mm 36 in 083N8306 083N8307 083N8307 – – – – (b) (b)1000 mm 40 in 083N8309 083N8310 083N8310 – – – – (b) (b)

– 42 in – – – – – – – (b) (b)– 44 in – – – – – – – (b) (b)

1200 mm 48 in 083N8312 083N8313 083N8313 – – – – (b) (b)1400 mm 54 in 083N8349 083N8353 083N8357 – – – – (b) –

– 60 in – – – – – – – (b) –1600 mm 66 in 083N8350 083N8354 083N8358 – – – – (b) –1800 mm 72 in 083N8351 083N8355 083N8359 – – – – (b) –2000 mm 78 in 083N8352 083N8356 083N8360 – – – – (b) –(a) Type “C” 304 ss rings are used with Neoprene, EPDM, Linatex, and Ebonite lined flowtubes. Rings are not needed for fluid reference

ground because flowtube includes grounding electrodes.(b) Contact Foxboro.

RING

GASKETBY USER

LINER

FLOWTUBE FLANGEBOLTS BY USER

PIPELINEFLANGE

FLOW

RELATIONSHIPOF PARTS

GASKETBY USER

PIPELINEFLANGE

FLOWTUBEFLANGE

RINGSEE TABLE 1

RINGASSEMBLY

BOLTHOLE FORSTRAP

RINGCONFIGURATION

PL 008-748Page 9

FIGURE 4Optional Type “E” Liner Protection (Grounding) Rings

Used for both Liner Protection and Process Fluid Groundingwith Flowtubes having ptfe Liners Only

Table 2. Part Numbers for Type “E” 316 ss Rings used for Liner Protection and Process Fluid Grounding(a)

Flowtube Size Flange Type with Type “E” 316 ss Ring - Part Numbers

DNFlange Size

InchFlange Size

DINPN 6

DINPN 10

DINPN 16

DINPN 25

DINPN 40

ANSICl. 150

ANSICl. 300

AS 2129Tbl. E

200 mm 8 in 083N8129 083N8130 083N8130 083N8131 083N8132 083N8370 083N8133 083N8134250 mm 10 in 083N8135 083N8136 083N8137 083N8138 083N8139 083N8140 083N8141 083N8143300 mm 12 in 083N8144 083N8144 083N8145 083N8146 083N8147 083N8148 083N8149 083N8151350 mm 14 in 083N8152 083N8153 083N8154 083N8155 083N8156 083N8157 083N8158 083N8153400 mm 16 in 083N8160 083N8161 083N8162 083N8163 083N8164 083N8165 083N8166 083N8161450 mm 18 in 083N8168 083N8169 083N8170 083N8171 083N8172 083N8173 083N8174 083N8176500 mm 20 in 083N8177 083N8178 083N8179 083N8180 083N8181 083N8182 083N8183 083N8185600 mm 24 in 083N8186 083N8187 083N8188 083N8189 – 083N8190 083N8191 083N8193

(a) Type “E” 316 ss rings are used with ptfe-lined flowtubes only. For flowtubes with a high temperature ptfe liner, two rings are provided as standard.

RING

GASKETBY USER

ptfeLINER

RING BOLT (4) BY USR

FLOWTUBE FLANGEBOLTS BY USER

GASKET BY USER

PIPELINE FLANGE

FLANGE BOLT HOLES

RING WITH FOURBOLT HOLES, SEE TABLE 2

RINGASSEMBLY

RELATIONSHIPOF PARTS

RINGCONFIGURATION

FOUR BOLT HOLES FOR BOLTING RINGTO FLOWTUBE FLANGE, BY USER

FOUR BOLT HOLESFOR BOLTING RING TO FLOWTUBE FLANGE, BY USER

FLOW

PL 008-748Page 10

RECOMMENDED SPARE PARTS SUMMARY

FigureNumber

ItemNumber

PartNumber Part Name

Number of Parts Recommended for

1 Inst.

5 Inst.

20 Inst.

1 2 083B0069 Plastic Terminal Box Cover and Gasket 1 1 22 3 D0164XG Gasket, Aluminum Terminal Box Cover 1 1 2

The Foxboro Company33 Commercial StreetFoxboro, MA 02035-2099United States of Americahttp://www.foxboro.comInside U.S.: 1-888-FOXBORO

(1-888-369-2676)Outside U.S.: Contact your local Foxboro representative.Facsimile (508) 549-4492

An Invensys company

Foxboro is a registered trademark of The Foxboro Company.Invensys is a trademark of Invensys plc.Hastelloy is a trademark of Haynes International.Linatex is a trademark of Wilkinson Process Rubber, Ltd.Monel is a trademark of Inco Alloys International, Inc.Neoprene is a trademark of E. I. duPont de Nemours & Company.All other brand names may be trademarks of their respective companies.

Copyright 2001 The Foxboro CompanyAll rights reserved

MB 150 Printed in U.S.A. 0601