PNEUMATIC CONVEYING SYSTEMS AND STORAGE … · Solution A: Pneumatic conveying system of wood pellets with suction probe and local storage. Pag 4 [email protected] 1 1 Suction

PNEUMATIC CONVEYING SYSTEMSAND STORAGE PELLET

PRODUCTS LIST

V.01eng

Pag 2 www.denaspirazioni.com [email protected]

INDEX

POSSIBLE APPLICATIONS WITH THE WX

Solution A: System of pneumatic conveying of wood pellets with suction probe and localstorage. pag. 4

Solution B: System of pneumatic conveying of wood pellets with two suction probes andlocal storage. pag. 5

Solution C: System of pneumatic conveying of wood pellets for pellet stove or thermo fi-replace with silo. pag. 6

Solution D: System of pneumatic conveying of wood pellets with multiple suction probesand local storage. pag. 7

Solution E: System of pneumatic conveying of wood pellets with suction big-bag. pag. 8

Solution F: System of pneumatic conveying of wood pellets from underground storagetank. pag. 9

Solution G: System of pneumatic conveying of pellets from storage silo. pag. 10

Solution H: System of pneumatic conveying of wood for long distances pellets for highdistances. pag. 11

PRODUCTS AND ACCESSORIES

PNEUMATIC CONVEYOR WX5 pag. 12



PNEUMATIC CONVEYOR WX50-55 pag. 15

GALVANIZED STEEL SILO pag. 16

INDOOR SACK SILO pag. 17

SPARE PARTS pag. 18

.


The pneumatic conveyors Dena series WX offer significant advantages over traditional power systems, the mostadvantageous is on the possibility to exploit the return air of the turbine that is conveyed inside the suctionprobe so it happens a gradual and continuous distribution of pellets in the intake circuit, it is possible to com-bine the WX to any type of silos or storage warehouse with flat bottom without the aid of mechanical systemsof extraction.

ADVANTAGES OF THE SYSTEM PNEUMATIC WX

Economic

With the WX can build a metal container, wood or masonry elementary buildingsaving the cost of purchasing the storage silos.

Pneumatic conveying suction

Among the numerous advantages the ability to perform, complex paths, the ab-sence of leaks or spills of material and the simplicity of the system

Automatic operation

The functioning of WX is fully automatic.

Quick and easy installation

The installation and commissioning are carried out quickly and easily.

Compatible with all boilers and pellet stoves

The available versions allow the application of any boiler or pellet stove on themarket and any silo interior, exterior or basement.

Gentle treatment

During the pneumatic transport the pellets is unloaded at destination clean andperfectly intact

Solution A: Pneumatic conveying system of wood pellets with suction probe and local storage.


1

1 Suction probe art n° PR0001

2 Discharge hopper WX10 art n° WX1001

3 Suction motor WX10 art n° WX1002

4 Hose pneumatic conveying pellets art n° TB0001

5 Return air hose art n° TB0001

6 Storage room

3

2


Solution B: Pneumatic conveying system of wood pellets with two suction probes andlocal storage

1






6 Storage room

3

2


Solution C: Pneumatic conveying system of wood pellets for pellet stove or thermo fire-place with silo.

1


2 Storage silo of 1 m3 art n° SL001M



5 Connection module for the suction system art n° PR00ES


6

5


Solution D: Pneumatic conveying system of wood pellets with multiple suction probes andlocal storage.

1





5 Manual changeover unit art n° PR0011


3

2 5


Solution E: Pneumatic conveying system of wood pellets with suction big-bag.

1

1 Suction probe big-bag art n° PR3669

2 Pneumatic conveyor WX15 art n° WX1015



2


Solution F: Pneumatic conveying system of wood pellets from underground storage tank.

1

1 Pneumatic conveyor WX15 art n° WX1015




Solution G: Pneumatic conveying system of pellets from storage silo.

1 Connection module for the suction system art n° PR00ES






2

3 1


Solution H: Pneumatic conveying system of wood for long distances pellets for long distances.

1

1 Connection module with extraction screw art n° CE00WX

2 Discharge hopper WX15G art n° WXG115

3 Steel pipe pneumatic conveying pellets art n° TB0002

4 Steel pipe in depression art n° TB0002



5

2


The pneumatic conveyor WX5 is ideal for dosing granular pro-ducts to automate your system with minimal expense and main-tenance.

� IDEAL FOR PELLET STOVES AND BIOMASS BOILERS� AUTOMATIC OPERATION� ADAPTABLE FOR ANY SYSTEM� PROGRAMMABLE BAND

MODEL Unit of measure WX5 WX5-S

Power W 1500 1500

Voltage V 230 230

Frequency Hz 50 50

Hopper capacity internal lt 3 3

Max. vacuum rate Mbar 2200 2200

Filter cleaning system / Manual Automatic

Pressure cleanig system Air - 6 bar

Structure Material Steel Steel

Total weight kg 22 22

Dimensions motor mm 270 x 210 x H 420 270 x 210 x H 420

Suction inlet mm Ø 50 Ø 50

Dimensions hopper mm 153 x 273 x H 250 153 x 273 x H 250

STANDARD EQUIPMENT

� Lcd control panel� Cartridge filter in polyester� Level sensor � Exhaust valve product� Cable alimentation shuko of 3 mt� Cable alimentation sensor of 2 mt

PNEUMATIC CONVEYOR WX5

ACCESSORIES

Suction probe

Article n°

PR0001Antistatic hose Ø 50

(min. 20mt)

Article n°

TB0001

Galvanized steelpipe Ø 50

Article n°

TB0002Support bracket for

motor WX10

Article n°

STWX01

90° bend steel

Article n°

CA5001Hose clamp to article

n° TB0001

Article n°

FS0001



� IDEAL FOR PELLET STOVES AND BIOMASS BOILERS� AUTOMATIC OPERATION� ADAPTABLE FOR ANY SYSTEM� PROGRAMMABLE BAND


Power W 1500 1500

Voltage V 230 230

Frequency Hz 50 50







Dimensions motor mm 270 x 210 x H 420 270 x 210 x H 420


Dimensions hopper mm 280 x H 270 280 x H 270

STANDARD EQUIPMENT

� Lcd control panel� Cartridge filter in polyester� Level sensor � Exhaust valve product� Cable alimentation shuko of 3 mt� Cable alimentation sensor da 2 mt


ACCESSORIES

Suction probe

Article n°


(min. 20mt)

Article n°

TB0001


Article n°

TB0002Support bracket for

motor WX10

Article n°

STWX01

90° bend steel

Article n°


n° TB0001

Article n°

FS0001



� IDEAL FOR PELLET BOILERS AND BIOMASS� AUTOMATIC OPERATION� ADAPTABLE FOR ANY SYSTEM� PROGRAMMABLE BAND


Power W 1500 1500

Voltage V 230 230

Frequency Hz 50 50







Ingombro mm 330 x H700 330 x H700


STANDARD EQUIPMENT

� Lcd control panel� Cartridge filter in polyester� Level sensor � Exhaust valve product� Cable alimentation shuko of 3 mt


ACCESSORIES

Suction probe

Article n°


(min. 20mt)

Article n°

TB0001


Article n°

TB0002Hose clamp to article

n° TB0002

Article n°

FS0002

Manual changeoverunit

Article n°

PR0011Hose clamp to article

n° TB0001

Article n°

FS0001


The pneumatic conveyor WX50 can pneumatically convey thegranules at long distances and with the flow of material up to400 kg/h.

� IDEAL FOR PELLET BOILERS AND BIOMASS� AUTOMATIC OPERATION� ADAPTABLE FOR ANY SYSTEM� PROGRAMMABLE BAND

MODEL Unit of measure WX50 WX55

Power kW 2,2 3

Voltage V 230-380 230-380

Frequency Hz 50 50



Filter cleaning system / Cartuccia autopulente Automatic

Pressure cleanig system Air 6 bar 6 bar



Dimensions motor mm 600x 600 x H 1300 600x 600 x H 1300


Dimensions hopper mm Ø 280 x H 700 Ø 280 x H 700

STANDARD EQUIPMENT

� Electrical panel installed on the vacuum motor� Filter cleaning system� Level sensor � Exhaust valve product� Vacuum motor remote

PNEUMATIC CONVEYOR WX50-WX55

ACCESSORIES

Suction probe

Article n°


(min. 20mt)

Article n°

TB0001


Article n°

TB0002Hose clamp to article

n° TB0002

Article n°

FS0002

90° bend steel

Article n°


n° TB0001

Article n°

FS0001


The storage silo SUM is ideal to complement all air extraction sy-stems.

� QUICK CONNECTION SUCTION PROBE� CONSTRUCTION GALVANIZED STEEL� SUITABLE FOR ANY SYSTEM WX� MANUAL FILLING WITH BAGS� SUPERIOR PROTECTION

Article n° Volume (m3) Tonnage Height A (cm) Dimensions BxC (cm) Extraction system

SL0001M 1 0,65 140 103x103 pneumatic

SL0001M 1 0,65 140 103x103 screw (0,18kw)

SL0015M 1.5 0,975 190 103x103 pneumatic

SL0015M 1.5 0,975 190 103x103 screw (0,18kw)

SL0003M 3 1,95 190 103x206 pneumatic

SL0003M 3 1,95 190 103x206 screw (0,18kw)

SL0005M 5 3,20 250 170x170 pneumatic

SL0005M 5 3,20 250 170x170 screw (0,18kw)

STORAGE SILO STEEL

ACCESSORIES

Module withpneumaticextraction

Article n°

PR00ESModule extension

by 0,5 m3

Article n°

ES0050

Module with extraction

screw

Article n°

PRCL01

Filler neck forpneumatic truck

storz 4”

Article n°

BR0004

90° bend steel

Article n°


n° TB0001

Article n°

FS0001

Assembly in series


The flexible pellet silo model SIT is fitted with an auger deliverysystem and suction adapter. The method of construction allowsit to be taken into any room in single parts and put together.Sides and cover of the pellet store are made of flexible and du-rable antistatic textile material. A compact steel frame, conicalbase and special delivery system provide optimal and reliableconveying of pellets.

� QUICK CONNECTION SUCTION PROBE� GALVANIZED STEEL FRAME� SUITABLE FOR ANY SYSTEM WX� PNEUMATIC FILLING SYSTEM� MADE OUT OF ANTI-STATIC, HIGH-RESISTANCE POLYESTER

STORAGE SILO TEXTILE

ACCESSORIES

90° bend steel

Article n°


n° TB0001

Article n°

FS0001

Article n° Volume (m3) Tonnage Height A (cm) Dimensions BxC (cm) Height D (cm) Extraction system

SIT5 5 3.2 204 206x206 225 pneumatic

SIT5-C 5 3.2 204 206x206 225 screw (0,18kw)

SIT8 8 5.2 204 256x256 225 pneumatic

SIT8-C 8 5.2 204 256x256 225 screw (0,18kw)

SIT10 10 6.4 204 306x306 225 pneumatic

SIT10-C 10 6.4 204 306x306 225 screw (0,18kw)

Module with pneumaticextraction

Articolo n°

PR00ESModule extension

by 0,5 m3

Articolo n°

ES0050

Module with extraction

screw

Articolo n°

PRCL01

Filler neck forpneumatic truck

storz 4”

Articolo n°

BR0004


SPARE PARTS

Single-phase motor

Article n°

MBP015Cartridge filter

Article n°

CAR150

Selenoid valve

Article n°

ELE001Sensor

Article n°

SENSO1

Kit motor brushes

Article n°

MSP015Lcd control panel

Article n°

CEQ001

Documents

PNEUMATIC CONVEYING SYSTEMS AND STORAGE … · Solution A: Pneumatic conveying system of wood pellets with suction probe and local storage. Pag 4 [email protected] 1 1 Suction