STRONG PARTNERS. TOUGH TRUCKS.

Powered Stacker with Folding PlatformS1.5S, S1.5Sil, S1.5Ssl

S1.5S, S1.5Sil, S1.5Ssl

Equipment and weight:Weights (line) are based on the following specifications:Complete truck with 180 mm wide forks (S1.5S) or 193 mm wide forks (S1.5 IL)or 100 mm forks (Straddle leg SL), polyurethane drive/steer tyre, and 2-Stage 2 965 mm mast

Forks:S1.5S: 65 x 180 x 1 160 mm longS1.5S IL: 65 x 193 x 1 160 mm longS1.5S SL: 35 x 100 x 1 200 mm long

Specification Data is based on VDI 2198

Mast and capacity informationValues shown are for standard equipment. When using non-standard equipment, these values may change. Please contact your Hyster dealer for information.

The rated capacities shown are for masts in a vertical position on trucks equipped with standard or sideshift carriage, and nominal lengthforks. Masts above the maximum fork heights shown in the mast table are classified as high lift, and depending on the tyre/treadconfiguration may require reduced capacity, restricted back tilt or wide tread.

Forks spacing:Inside to inside: 210mm (S1.5S) 184mm (S1.5S IL)Outside to outside: 570 mm (1.5S) 570 mm (S1.5S IL)

800 mm, 1 000 mm, 1 200 mm adjustable (S1.5S SL)

NOTE:

Specifications are affected by the condition

of the vehicle and how it is equipped, as well

as the nature and condition of the operating

area. If these specifications are critical, the

proposed application should be discussed

with your dealer.

Traction, lift, and lower speeds may

vary with alternative lift height

Values determined by wheel friction, if

climbing ramps frequently (within 1h),

consult your salesman

() Value or text in brackets are referred

to truck fitted out with side fix

protection (biga) or rear fix protection

(bob)

Values are referred to a 2-stg mast

HiVi, h3=2 968 mm

If truck fitted out with three stage FFL

mast,h3=4 628 mm add 172 kg

Values referred to truck equipped with

2-stg mast, and battery at row 6.4,

add 50 Kg when fitted out with side

fix protection (biga) or rear fix

protection (bob)

+ 61 with fixed lateral protections

(Biga), + 110 with Rear protections

(Bob)

¶ + 75 with fixed lateral protections

(Biga), + 114 with Rear protections

(Bob)

† Values + 18 mm with 3-stg mast

Values + 12 mm with 3-stg mast

Values - 18 mm with 3-stg mast

Mast tables:

h1 with 100 mm free lift

h4 with load backrest add 528 mm

When initial lift is lifted add 130 mm

Notice

Care must be exercised when handling

elevated loads. When the carriage

and/or load is elevated, truck stability

is reduced. It is important that mast tilt

in either direction be kept to a

minimum when loads are elevated.

Operators must be trained and adhere

to the instructions contained in the

Operating Manual.

Safety:

This truck conforms to the current EU requirements.

Hyster products are subject to change without notice.

Lift trucks illustrated may feature optional equipment.

■ S1.5S Powered stacker with folding platform

■ S1.5Sil Powered stacker with folding platform, initial lift

■ S1.5Ssl Powered stacker with folding platform, straddle legs

Also available with tandem load wheels

Dependability

■ MOSFET high frequency Combi controller for traction and hydraulic controls.

■ Welded fork construction makes them highly resistant to torsion and heavy loads.

■ Hour meter and battery discharge indicator with lift interrupt fitted as standard.

■ Cold store protection for application to -30 C.

■ Specific 'initial lift' and 'straddle legs' models provide the right answer to any application.

■ High visibility and full free lift 2 and 3-stage masts availability.

Productivity

■ Operator-friendly tiller head controls for productive load handling.

■ Regenerative braking and anti-rollback both available as standard.

■ Pedestrian or stand-on operation, with or without side arms raised for improved poductivity.

■ Progressive speed control and steering system ensure optimum performance levels.

■ Tandem load wheels and exit/entry rollers as standard.

■ Key-pad with PIN code for enhanced fleet management.

■ Power steering makes truck highly manoeuvrable.

Ergonomics

■ Ergonomically designed tiller head for maximum operator comfort.

■ Low effort controls ergonomically positioned to reduce operator fatigue.

■ Dual lift/lower controls allow operation using either hand.

■ 'Corner control' system reduces speed automatically when cornering.

■ 5-point wheel layout, with fixed stabilizer wheels, provides enhanced stability.

■ Adjustable performance settings to suit specific operating conditions.

Cost of ownership

■ AC drive motor provides superior performance and reduced operation costs.

■ Power transmission supplied via helicoidal gears, running in oil bath.

■ IP54 standards control for protection against dust and water.

■ Optimum component reliability permit the extension of service materials.

Serviceability

■ AC drive motor and brushless lift motor construction ensures low maintenance requirements.

■ Built-in diagnostic system for preventative maintenance communication reduces downtime.

■ Driver Diagnostic Interface (DDI) allows selection of appropriate performance settings for specific applications.

■ CANbus technology for increased functionality, reliability and servicing.

Product Features

Hyster Europe, Flagship House, Reading Road North, Fleet, Hants GU51 4WD, England.

Tel: +44 (0) 1252 810261 Fax: +44 (0) 1252 770702

Email: info@hyster.co.uk http://www.hyster.co.uk

A division of NACCO Materials Handling Limited.

02/08/TLC Printed in EnglandForm No. 901299/0

Hyster®, ®, Vista® and Monotrol® are registered trademarks of Hyster Company in the United States and in certain other countries.TM, FortensTM, Pacesetter VSMTM, DuraMatchTM, DuraMatch PlusTM, TouchPointTM, TouchControlTM, EZXchange & HSMTM are trademarks

of Hyster Company in the United States and in certain other countries. TM

Strong Partners, Tough Trucks,

for Demanding Operations Everywhere.

Hyster supplies a complete product range,

including Warehouse trucks, IC and Electric

Counterbalanced trucks, Container Handlers

and Reach Stackers.

Hyster is committed to being much more than a

lift truck supplier. Our aim is to offer a complete

partnership capable of responding to the full

spectrum of materials handling issues:

Whether you need professional consultancy on

your fleet management, fully qualified service

support, or reliable parts supply, you can

depend on Hyster.

Our network of highly trained dealers provides

expert, responsive local support. They can offer

cost-effective finance packages and introduce

effectively managed maintenance programmes

to ensure that you get the best possible value.

Our business is dealing with your materials

handling needs so you can focus on the

success of your business today and in the

future.