RE 17334 2007-10 PDFs/BRH CYL/Rexroth...Hydraulic cylinder 1/44 Mill type Series CDH2 / CGH2 Component series 1X Nominal pressure 250 bar (25 MPa) RE 17334/10.07 Replaces: 09.05 Overview

1/44Hydraulic cylinderMill type

Series CDH2 / CGH2

Component series 1X Nominal pressure 250 bar (25 MPa)

RE 17334/10.07Replaces: 09.05

Overview of contents

Contents Page

Technical data 2

Diameter, weights 2

Areas, forces, flows 3

Tolerances 3

IHC-Designer: Engineering software 4

Mounting style overview 4

Ordering details 4

Plain clevis at base MP3 6

Self-aligning clevis at base MP5 8

Round flange at head MF3 10

Round flange at base MF4 12

Trunnions MT4 14

Foot mounting MS2 16

H4652_d

Features

– Standards: DIN 24333, ISO 6022 and VW 39 D 921

– 6 mounting styles

– Piston Ø: 40 to 320 mm

– Piston rod Ø: 25 to 220 mm

– Stroke length up to 6 m

Contents Page

Flange connections 18

Position measuring system 20

Proximity switch 24

Screwed coupling 26

Self-aligning clevis 27

Fork clevis 28

Mounting block 29

Buckling 32

End position cushioning 35

Spare parts 38

Tightening torques 40

Seal kits 41

Engineering software Interactive Catalog System

Download of brochures

www.boschrexroth.com/ics

www.boschrexroth.com/ business_units/bri/de/downloads/ihc

Online

Features 1

Technical data (for applications outside these parameters, please consult us!) 2

Diameter, weights 2

Areas, forces, flows 3

Tolerances to ISO 8135: 1999E 3

Engineering software ICS (Interactive Catalog System) 4

Mounting style overview 4

Ordering details 4

Plain clevis at base MP3 6

Self-aligning clevis at base MP5 8

Round flange at head MF3 10

Round flange at base MF4 12

Trunnions MT4 14

Foot mounting MS2 16

Flange connections 18

Position measuring system 20

Proximity switch 24

Coupling (dimensions in mm) 26

Self-aligning clevis CGKD (dimensions in mm) 27

Fork clevis CCKB (dimensions in mm) 28

Trunnion bracket CLTB (dimensions in mm) 29

Clevis bracket CLCA (dimensions in mm) 30

Clevis bracket CLCD (dimensions in mm) 31

Buckling 32

Permissible stroke lengths (dimensions in mm) 32

End position cushioning 35

Spare parts 38

Tightening torque 40

Seal kits1) 41

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

2/44 Bosch Rexroth AG Hydraulics CDH2 / CGH2 RE 17334/10.07

Technical data (for applications outside these parameters, please consult us!)

Standards: The installation dimensions of the cylinders and mounting styles meet the requirements of DIN 24333 and ISO 6022.Nominal pressure: 250 bar Static proof pressure: 375 bar Higher operating pressures on request.The specified operating pressures are only valid for applications with shock-free operation. If extreme loads occur, e.g. as happens in high sequence cycles, the fixings and piston rod thread connections need to be designed for durability (fatigue strength).Installation: OptionalPressure fluid / pressure fluid temperature range: HL, HLP, HFD-R: –20 °C to +80 °C HFA: +5 °C to +55 °C Water glycole HFC on requestViscosity range: 2.8 to 380 mm2/sISO cleanliness class Maximum permissible degree of pressure fluid contamination is to ISO 4406 (c) class 20/18/15.Stroke velocity: Up to 0.5 m/s (depending on the connection

ports), higher stroke velocities on requestBleed screw as standard: Secured against unscrewingUndercoat: The hydraulic cylinders are, as standard, painted (colour tone gentian blue RAL 5010) with a max. thickness of 80 μm. Other colour tones on request.Acceptance: Each cylinder is tested to Bosch Rexroth standards.Safety notes:For assembly, commissioning and maintenance cylinders, please take the operating guidelines stated in RE 07100-B into account!Service and repair work may only be carried out by Bosch Rex-roth AG and specifically trained personnel. No warranty claims will be accepted for damage resulting from assembly, mainte-nance and repair work not carried out by Bosch Rexroth AG.Checklists for hydraulic cylinders:Cylinders, the technical and/or operating data of which differ from the paramters given in the data sheet, can only be offered as special variants on request. For the preparation of offers, de-viations of technical data and/or operating data must be descri-bed in the checklists for hydraulic cylinders (RE 07200).

Diameter, weights

1) Weight without position measuring system

Piston Piston rod

CD cylinder at 0 mm stroke length

Per 100 mm stroke length

CG cylinder at 0 mm stroke length

Per100 mm stroke length

AL Ø

mm

MM Ø

mm

MP3 1) MP5 1)

kg

MP3 2) MP5 2)

kg

MF3 MF4 kg

MT4

kg

MS2

kg

kg

MF3

kg

MT4

kg

MS2

kg

kg

40 25 7 12 9 9 9 0.9 10 10 10 1.328 7 12 9 9 9 1.0 10 10 10 1.5

50 32 12 19.5 14 13 13 1.3 16 16 16 1.936 12 19.5 14 13 14 1.5 16 16 16 2.3

63 40 20 29.5 21 21 21 2.3 25 25 25 3.345 20 29.5 21 21 21 2.6 25 25 25 3.8

80 50 32 42.5 35 34 35 3.2 41 40 41 4.756 32 42.5 35 34 36 3.6 41 40 42 5.5

100 63 51 64.5 54 54 55 5.2 63 63 64 7.670 51 64.5 55 54 56 5.7 64 64 65 8.8

125 80 95 114 96 99 98 8.2 113 115 114 12.190 96 115 97 100 99 9.2 115 117 116 14.2

140 90 131 157 132 136 137 10.7 155 158 159 15.7100 132 158 133 137 138 11.9 156 160 161 18.1

160 100 185 220 184 197 206 12.6 217 231 239 18.8110 186 221 186 199 207 13.9 220 233 242 21.4

180 110 255 303 253 264 274 14.7 294 305 314 22.1125 258 304 256 267 277 16.8 300 311 320 26.5

200 125 349 405 332 350 363 19.0 359 377 389 28.6140 352 406 335 353 366 21.5 365 383 396 33.5

220 140 527 625 512 546 518 27.1 604 638 610 39.1160 30.9 46.7

250 160 673 795 640 677 650 32.7 761 798 772 48.5180 36.9 56.9

280 180 976 1192 966 1020 918 44.2 1130 1183 1081 64.2200 48.8 73.4

320 200 1251 1512 1172 1223 1174 55.2 1354 1405 1356 79.8220 60.4 90.2

2) Weigth with position measuring system

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

F1

F3 qV3

A3 A1

qV1

F2 A2

qV2

Hydraulics Bosch Rexroth AGRE 17334/10.07 CDH2 / CGH2 3/44

Areas, forces, flows

Piston Piston Area Areas Force at 250 bar 1) Flow at 0.1 m/s 2)

rod ratio Piston Rod Annulus Pressure Diff. Pulling Out Diff. In

ALØ mm

MMØ mm

ϕ A1/A3

A1cm2

A2cm2

A3cm2

F1kN

F2kN

F3kN

qV1l/min

qV2l/min

qV3l/min

40 25 28

1.64 1.96

12.564.90 6.16

7.65 6.40

31.4012.25 15.40

19.12 16.00

7.52.9 3.7

4.6 3.8

50 32 36

1.69 2.08

19.638.04 10.18

11.59 9.45

49.1020.12 25.45

28.98 23.65

11.84.8 6.1

7.0 5.7

63 40 45

1.67 2.04

31.1712.56 15.90

18.61 15.27

77.9031.38 39.75

46.52 38.15

18.77.5 9.5

11.2 9.2

80 50 56

1.66 1.96

50.2619.63 24.63

30.63 25.63

125.6549.07 61.55

76.58 64.10

30.211.8 14.8

18.4 15.4

100 63 70

1.66 1.96

78.5431.16 38.48

47.38 40.06

196.3577.93 96.20

118.42 100.15

47.118.7 23.1

28.4 24.0

125 80 90

1.69 2.08

122.7250.24 63.62

72.48 59.10

306.75125.62 159.05

181.13 147.70

73.630.14 38.2

43.46 35.4

140 90 100

1.70 2.04

153.9463.62 78.54

90.32 75.40

384.75159.05 196.35

225.70 188.40

92.438.2 47.1

54.2 45.3

160 100 110

1.64 1.90

201.0678.54 95.06

122.50 106.00

502.50196.35 237.65

306.15 264.85

120.647.1 57.0

73.5 63.6

180 110 125

1.60 1.93

254.4795.06 122.72

159.43 131.75

636.17237.65 306.80

398.52 329.37

152.757.0 73.6

95.7 79.1

200 125 140

1.64 1.96

314.16122.72 153.96

191.44 160.20

785.25306.80 384.90

478.45 400.35

188.573.6 92.4

114.9 96.1

220 140 160

1.68 2.12

380.1153.96 201.0

226.2 179.1

950.3384.9 502.6

565.5 447.7

228.192.4 120.7

135.7 107.4

250 160 180

1.69 2.08

490.8201.0 254.4

289.8 236.4

1227.2502.6 636.2

724.5 590.0

294.5120.7 152.7

173.8 141.8

280 180 200

1.70 2.04

615.7254.4 314.1

361.3 301.6

1539.4636.2 785.4

903.2 753.9

369.4152.7 188.5

216.7 180.9

320 200 220

1.64 1.90 804.2 314.1

380.1490.1 424.2 2010.6 785.4

950.31225.2 1060.3 482.5 188.5

228.1294.0 254.4

1) Theoretical force (efficiency not taken into account)

Tolerances to ISO 8135: 1999E

1) Not standardised

2) Stroke velocity

2) Including the stroke length

Installation dimensions Y PJ WC XC2) XO2) XS1), 2) SS XV2) ZP2) Stroke tolerancesMounting style all all MF3 MP3 MP5 MS2 MS2 MT4 MF4

Stroke length Tolerances

≤ 1250 ± 2 ± 1,5 ± 2 ± 1,5 ± 1,5 ± 2 ± 1,5 ± 2 ± 1,5 + 2

> 1250 – ≤ 3150 ± 4 ± 3 ± 4 ± 3 ± 3 ± 4 ± 3 ± 4 ± 3 + 5

> 3150 – ≤ 8000 ± 8 ± 5 ± 8 ± 5 ± 5 ± 8 ± 5 ± 8 ± 5 + 8

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Ordering details

CDH2 MT4See pages 14, 15

CGH2 MT4See pages 14, 15

CDH2 MS2See pages 16, 17

CGH2 MS2See pages 16, 17

CDH2 MP5See pages 8, 9

CDH2 MF3See pages 10, 11

CGH2 MF3See pages 10, 11

CDH2 MP3See pages 6, 7

CDH2 MF4See pages 12, 13

Mounting style overview

1) = Only piston rod Ø 25 to 110 mm2) = Only piston rod Ø 25 to 140 mm3) = The trunnion can be located as required. Dim. „XV” must always be stated in clear text

in mm in case of an order.4) = Only piston Ø 40 to 200 mm5) = Only possible in conjuction with position

measuring system „T“ 6) = Only piston Ø 63 to 200 mm7) = Only MF3; MT4; MS2; not standardised8) = Seal versions A, B is not possible Piston rod version „H“ is not possible

End position damping possible from piston rod Ø 45 mm CG version is not possible

Piston rod Ø 25 mm is not possible Take the max. stroke lengths on page 21 into account

9) = Only piston Ø 80 to 320 mm 10) = Not possible for version MF4 11) = Standard for seal versions M, T, S and piston Ø 220 to

320 mm Not possible for seal versions A, B 12) = For the CG version only one self-aligning clevis is fitted13) = For the CG version only one one rod end14) = Not standardised15) = Take the permissible stroke lengths on pages 32 to 34

into account

Engineering software ICS (Interactive Catalog System)

The ICS (Interactive Catalog System) is a selection and engi-neering aid for hydraulic cylinders. With the help of the ICS, designers of plant and machinery can quickly and reliably find the optimum hydraulic cylinder solution through logic-guided type code queries. This software helps to solve design and en-gineering tasks more quickly and efficient. After having been

guided through the product selection, the user gets the exact technical data of the selected components as well as 2D and 3D CAD data in the correct file format for all common CAD systems quickly and reliably.

This allows users to reduce costs while increasing their com-petitiveness.

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Ordering details

Differential cylinder = CD Double rod cylinder 7) = CG

Series = H2

Mounting stylesPlain clevis at base = MP3 Self-aligning clevis at base = MP5 Round flange at head = MF3 Round flange at base = MF4 Trunnions 3) = MT4 Foot mounting 14) = MS2

Piston Ø (40 to 320 mm) See page 2

Piston rod Ø (25 to 220 mm) See page 2

Stroke length in mm 15)

Design principle Head and base flanged = A

Component series10 to 19 unchanged installation and connection dimensions = 1X

Connection ports/versionPipe thread to ISO 228/1 Metric ISO thread Flange porting pattern to ISO 6162 Tab.1 (=̂SAE 3000 PSI) Flange porting pattern to ISO 6162 Tab.2 (=̂SAE 6000 PSI) Flange porting pattern to ISO 6164 Tab.1 Flange porting pattern to ISO 6164 Tab.2 Pipe thread to ISO 228/1 with a ring flange that has a machined flat

6), 10)

9), 10)

4), 10)

10)

= = = = = = =

B M F D K H C

Connection port/position at head and base = 1

1

2

3

4

Viewed on the piston rod

= 2= 3= 4

Piston rod versionHard chromium plated = C Hardened and hard chromium plated 1) = HNickel plated and hard chromium plated 2) = N

Option 2 B = Flange grease nipple C = 5) Analogue output

4-20 mA F = 5) Analogue output

0-10 V D = 5) Digital output SSI Y = 13) Enter piston rod

extention LY in clear text

in mm W = Without option

Option 1A = Screwed coupling,

both sides F = 11) Guide rings E = Inductive proximity

switch without plug-in connector

Plug-in connector – separate order, see page 24

T = 8) Position measuring system (magnetostrictive) without plug-in connector

Plug-in connector – separate order, see page 23

W = Without option

Seal versionSuitable for mineral oil

to DIN 51524 HL, HLP and HFA

M = Standard seal system T = Servo quality/reduced friction A = Chevron seal kits

Suitable for phosphate ester HFD-R

S = Servo quality/reduced friction B = Chevron seal kits

End position cushioningU = Without D = 4) Both sides, self adjusting E = Both sides, adjustable

Piston rod endH = Thread for self-aligning clevis CGKD F = 12) With mounted self-aligning clevis

CGKD

H2 A 1X

Ordering examples:

CDH2 MT4/63/45/350A1X/B1CHDMWW, XV = 300 mm

CDH2 MP5/80/56/500A1X/B1CHDMWW

CGH2 MF3/100/70/500A1X/B1CHUMWW

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

5)

EE

Ø D

A

KK

Ø M

M

Ø D

WA

A XC + X*

PJ + X*Y

Ø D42)

EENV

G 1

/41)

Ø D42)

Ø R

A

VE

X1 X1

MR

10)

LM1

"A"

"A"L1

Ø C

D

EW

"A-A"

Ø R

A

VE


Plain clevis at base MP3

CDH2 MP3

CDH2 MP3: for seal versions „A”, „B” and AL-Ø 160 - 320 mm

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Dimensions MP3 (dimensions in mm)

AL Ø

MM Ø

KK A NV D DA D4 2)

EE 4)

EE 4)

Y PJ X1 WA XC

40 6) 25/28 M20x1.5 28 19/22 88 50 34 G1/2 M22x1.5 83 120 41 18 282

50 32/36 M27x2 36 27/30 102 60 34 G1/2 M22x1.5 98 120 48.5 18 305

63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21 348

80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24 395

100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27 442

125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31 520

140 6) 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31 580

160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35 617

180 6) 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40 690

200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40 756

220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42 890

250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42 903

280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48 1072

320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48 1080

AL = Piston Ø

MM = Piston rod Ø

X* = Stroke length Stroke and overall length tolerances to ISO 8135

1) = Bleeding: When viewed on the piston rod, the orientation is always offset by 90° to the pipe connection (in a clockwise direction)

2) = Ø D4 max. 0.5 mm deep3) = M50 x 2 available on request4) = For flange connections see separate table on

pages 18 and 19

AL Ø

MM Ø

L L1 MR M1 CD H9

EW h12

RA7)

f8VE7) RA8) VE8)

40 6) 25/28 53 8 32 32 25 25 52 29 88 –

50 32/36 61 8 40 40 32 32 63 29 102 –

63 40/45 74 8 50 50 40 40 75 32 120 –

80 50/56 90 10 63 63 50 50 90 36 145 –

100 63/70 102 12 71 71 63 63 110 41 170 –

125 80/90 124 16 90 90 80 80 132 45 206 –

140 6) 90/100 149 16 100 100 90 90 145 45 226 –

160 100/110 150 16 112 112 100 100 160 50 200 9) 50

180 6) 110/125 180 20 129 129 110 110 185 55 220 9) 55

200 125/140 206 20 145 145 125 125 200 61 235 9) 61

220 6) 140/160 253 20 170 178 160 160 235 71 270 71

250 160/180 253 24 170 178 160 160 250 71 300 9) 71

280 6) 180/200 320 30 220 230 200 200 295 88 325 88

320 200/220 320 30 220 230 200 200 320 88 365 9) 88

5) = Throttle valve only with end position damping "E" (180° to the bleed point)

6) = Piston Ø not standardised7) = Dimensions for cylinder with seal versions M, T and S8) = Dimensions for cylinder with seal versions A and B9) = Tolerance: f810) = Grease nipple; cone head form A to DIN 7141211) = Associated pin Ø r6

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

5)

EE

Ø D

A

KK

Ø M

M

Ø D

WA

A XO + X*

PJ + X*Y

Ø D42)

EENV

G 1

/41)

Ø D42)

Ø R

A

VE

X1 X1

MS

10)

LTM1

"A"

"A"L1

EP

EX

Ø C

X11)

ZZ

"A-A"

Ø R

A

VE


Self-aligning clevis at base MP5

CDH2 MP5

CDH2 MP5: for seal versions „A”, „B” and AL-Ø 160 - 320 mm

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Dimensions MP5 (dimensions in mm)

AL = Piston Ø

MM = Piston rod Ø


1) = Bleeding: When viewed on the piston rod, the orientation always offset by 90° to the pipe connection (in a clockwise direction)


pages 18 and 19

5) = Throttle valve only with end position cushioning "E" (180° to the bleed point)

6) = Piston Ø not standardised7) = Dimensions for cylinder with seal versions M, T and S8) = Dimensions for cylinder with seal versions A and B9) = Tolerance: f810) = Grease nipple; cone head form A to DIN 7141211) = Associated pin Ø r6

AL Ø

MM Ø

KK A NV D DA D4 2)

EE 4)

EE 4)

Y PJ X1 WA XO

40 6) 25/28 M20x1.5 28 19/22 88 50 34 G1/2 M22x1.5 83 120 41 18 282

50 32/36 M27x2 36 27/30 102 60 34 G1/2 M22x1.5 98 120 48.5 18 305

63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21 348

80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24 395

100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27 442

125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31 520

140 6) 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31 580

160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35 617

180 6) 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40 690

200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40 756

220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42 890

250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42 903

280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48 1072

320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48 1080

AL Ø

MM LT L1 MS M1 CX11)

H7EP EX

h12RA7)

f8VE7) RA8) VE8) Z

40 6) 25/28 53 8 32 32 25 22 25 52 29 88 – 2°

50 32/36 61 8 40 40 32 27 32 63 29 102 – 4°

63 40/45 74 8 50 50 40 32 40 75 32 120 – 4°

80 50/56 90 10 63 63 50 40 50 90 36 145 – 4°

100 63/70 102 12 71 71 63 52 63 110 41 170 – 4°

125 80/90 124 16 90 90 80 66 80 132 45 206 – 4°

140 6) 90/100 149 16 100 100 90 72 90 145 45 226 – 4°

160 100/110 150 16 112 112 100 84 100 160 50 200 9) 50 4°

180 6) 110/125 180 20 129 129 110 88 110 185 55 220 9) 55 4°

200 125/140 206 20 145 145 125 102 125 200 61 235 9) 61 4°

220 6) 140/160 253 20 170 178 160 130 160 235 71 270 71 4°

250 160/180 253 24 170 178 160 130 160 250 71 300 9) 71 4°

280 6)) 180/200 320 30 220 230 200 138 200 295 88 325 88 4°

320 200/220 320 30 220 230 200 162 200 320 88 365 9) 88 4°

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

VE

Ø R

A

5)EE

Ø D

A

KK

Ø M

M

Ø D

A

PJ + X*Y

Ø D42)

EENV

G 1

/41)

Ø D42)

Ø R

D

X1 X1FC

UC

FB

ZB + X*

VD

WC NF

45ϒ

22,5ϒ 22,5ϒ

5)EE

Ø D

A

KK

Ø M

M

Ø D

A

PK + X*Y

Ø D42)

EENV

G 1

/41)

Ø D42)

Ø R

D

X1 X1

FC

UC

FB

ZM + 2 x X*

VD

WC NF

45ϒ

22,5ϒ 22,5ϒ

WA + X*

VE

Ø R

A


Round flange at head MF3

CDH2 MF3

CGH2 MF310): for seal versions „A”, „B” and AL-Ø 160 - 320 mm

CGH2 MF310)

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Dimensions MF3 (dimensions in mm)

AL = Piston Ø

MM = Piston rod Ø



2) = Ø D4 max. 0.5 mm deep3) = M50 x 2 available on request

4) = For flange connections see separate table on pages 18 and 19


6) = Piston Ø not standardised7) = Dimensions for cylinder with seal versions M, T and S8) = Dimensions for cylinder with seal versions A and B9) = Tolerance: f810) = Double roded cylinders are not standardised

AL Ø

MM Ø

KK A NV D DA D4 2)

EE 4)

EE 4)

Y PJ X1 WA

40 6) 25/28 M20x1.5 28 19/22 88 50 34 G1/2 M22x1.5 83 120 41 18

50 32/36 M27x2 36 27/30 102 60 34 G1/2 M22x1.5 98 120 48.5 18

63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21

80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24

100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27

125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31

140 6) 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31

160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35

180 6) 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40

200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40

220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42

250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42

280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48

320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48

AL Ø

MM Ø

RD f8

WC VD NF js13

PK ZB max.

ZM FB H13

FC js13

UC Ø-1

RA7)

f8VE7) RA8) VE8)

40 6) 25/28 52 22 4 25 120 230 286 11 115 138 52 29 88 –

50 32/36 63 22 4 25 120 244 316 13.5 132 155 63 29 102 –

63 40/45 75 25 4 28 133 274 357 13.5 150 175 75 32 120 –

80 50/56 90 28 4 32 155 305 395 17.5 180 210 90 36 145 –

100 63/70 110 32 5 36 171 340 439 22 212 250 110 41 170 –

125 80/90 132 36 5 40 205 396 511 22 250 290 132 45 206 –

140 6) 90/100 145 36 5 40 219 430 551 26 280 325 145 45 226 –

160 100/110 160 40 5 45 235 467 605 26 315 360 160 50 200 9) 50

180 6) 110/125 185 45 5 50 264 510 652 33 350 405 185 55 220 9) 55

200 125/140 200 45 5 56 278 550 718 33 385 440 200 61 235 9) 61

220 6) 140/160 235 50 8 63 326 637 814 39 435 500 235 71 270 71

250 160/180 250 50 8 63 326 650 840 39 475 540 250 71 300 9) 71

280 6) 180/200 295 56 8 80 375 752 955 45 555 630 295 88 325 88

320 200/220 320 56 8 80 391 760 955 45 600 675 320 88 365 9) 88

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

Ø R

A

VE

EE

Ø D

A

KK

Ø M

M

Ø D

WA

A ZP + X*

PJ + X*Y

Ø D42)

EENVØ D42)

Ø R

A

VEX1 X1

VA

Ø B

A

NF

FC

UC

5)

G 1

/41)FB

45ϒ

22,5ϒ 22,5ϒ


Round flange at base MF4

CDH2 MF4

CDH2 MF4: for seal versions „A”, „B” and AL-Ø 160 - 320 mm

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Dimensions MF4 (dimensions in mm)

AL = Piston Ø

MM = Piston rod Ø



2) = Ø D4 max. 0.5 mm deep3) = M50 x 2 available on request

4) = For flange connections see separate table on pages 18 and 19


6) = Piston Ø not standardised7) = Dimensions for cylinder with seal versions M, T and S8) = Dimensions for cylinder with seal versions A and B9) = Tolerance: f8

AL Ø

MM Ø

KK A NV D DA D4 2)

EE 4)

EE 4)

Y PJ X1 WA

40 6) 25/28 M20x1.5 28 19/22 88 50 34 G1/2 M22x1.5 83 120 41 18

50 32/36 M27x2 36 27/30 102 60 34 G1/2 M22x1.5 98 120 48.5 18

63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21

80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24

100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27

125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31

140 6) 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31

160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35

180 6) 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40

200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40

220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42

250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42

280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48

320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48

AL Ø

MM Ø

ZP NF js13

VA BA H8

FB H13

FC js13

UC Ø-1

RA7)

f8VE7) RA8) VE8)

40 6) 25/28 250 25 5 52 11 115 138 52 29 88 –

50 32/36 265 25 4 63 13.5 132 155 63 29 102 –

63 40/45 298 28 4 75 13.5 150 175 75 32 120 –

80 50/56 332 32 5 90 17.5 180 210 90 36 145 –

100 63/70 371 36 5 110 22 212 250 110 41 170 –

125 80/90 430 40 6 132 22 250 290 132 45 206 –

140 6) 90/100 465 40 5 145 26 280 325 145 45 226 –

160 100/110 505 45 7 160 26 315 360 160 50 200 9) 50

180 6) 110/125 550 50 10 185 33 350 405 185 55 220 9) 55

200 125/140 596 56 10 200 33 385 440 200 61 235 9) 61

220 6) 140/160 690 63 10 235 39 435 500 235 71 270 71

250 160/180 703 63 10 250 39 475 540 250 71 300 9) 71

280 6) 180/200 822 80 10 295 45 555 630 295 88 325 88

320 200/220 830 80 10 320 45 600 675 320 88 365 9) 88

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

5)EE

Ø D

A

KK

Ø M

M

Ø D

WAA

PK + X*10)Y

Ø D42)

EENV

G 1

/41)

Ø D42)

Ø R

A

VE

X1 X1

UV

TL TM

r

Ø T

D

TLXV12)

ZM + 2 x X*10)

BD

WA + X*

VE

Ø R

A

5)EE

Ø D

A

KK

Ø M

M

Ø D

WAA

PJ + X*10)Y

Ø D42)

EENV

G 1

/41)

Ø D42)

Ø R

A

VE

X1 X1

UV

TL TM

r

Ø T

D

TLXV12)

ZB + X*10)

BD

Ø R

A

Ø R

A

VE VE

Ø R

A

VE

XVLY


Trunnions MT4

CDH2 MT4

CGH2 MT411): for seal versions „A”, „B” und AL-Ø 160 - 320 mm

CGH2 MT411)

CDH2 MT4: for seal versions „A”, „B” und AL-Ø 160 - 320 mm Dimensions for a cylinder with a rod extension „LY“ in the retracted condition

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Dimensions MT4 (dimensions in mm)

AL = Piston Ø

MM = Piston rod Ø




pages 18 and 195) = Throttle valve only with end position damping "E"

(180° to the bleed point)

6) = Piston Ø not standardised7) = Dimensions for cylinder with seal versions M, T and S8) = Dimensions for cylinder with seal versions A and B9) = Tolerance: f810) = Take the minimum stroke length „X*min.” into account11) = Double roded cylinders are not standardised12) = The trunnions can be located as required.

Dim. „XV” must always be stated in clear text, in the case of an order, in mm. Take „XVmin.” and „XVmax.” into account.

13) = XVmid. recommendation: The trunnions are located in the middle of the cylinder

14) = Tolerances according to EN ISO 9013: Thermal Cutting

AL Ø

MM Ø

KK A NV D DA D4 2)

EE 4)

EE 4)

Y PJ X1 WA

40 6) 25/28 M20x1.5 28 19/22 88 50 34 G1/2 M22x1.5 83 120 41 18

50 32/36 M27x2 36 27/30 102 60 34 G1/2 M22x1.5 98 120 48.5 18

63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21

80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24

100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27

125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31

140 6) 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31

160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35

180 6) 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40

200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40

220 6) 140/160 M125x4 125 120/140 355 273 65 G1 1/2 M48x2 3) 244 326 174 42

250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42

280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48

320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48

AL Ø

MM Ø

PK ZB max.

ZM X* min.

XV13)

mittXV12)

min.XV12)

max.BD UV

14)TD f8

TL js16

TM h13

r RA7)

f8VE7) RA8) VE8)

40 6) 25/28 120 230 286 22 143+X*/2 154 140+X* 38 88 25 20 95 0.8 52 29 88 –

50 32/36 120 244 316 32 158+X*/2 174 151+X* 38 102 32 25 112 0.8 63 29 102 –

63 40/45 133 274 357 47 178.5+X*/2 202 167+X* 48 120 40 32 125 1 75 32 120 –

80 50/56 155 305 395 58 197.5+X*/2 226,5 180,5+X* 58 150 50 40 150 1 90 36 145 –

100 63/70 171 340 439 79 219.5+X*/2 259 195+X* 78 175 63 50 180 1.2 110 41 170 –

125 80/90 205 396 511 91 255.5+X*/2 301 225+X* 98 220 80 63 224 1.2 132 45 206 –

140 6) 90/100 219 430 551 121 275.5+X*/2 336 230+X* 118 240 90 70 265 1.5 145 45 226 –

160 100/110 235 467 605 142 302.5+X*/2 373.5 251.5+X* 128 270 100 80 280 1.5 160 50 200 9) 50

180 6) 110/125 264 510 652 158 326+X*/2 405 267+X* 138 310 110 90 320 1.5 185 55 220 9) 55

200 125/140 278 550 718 204 359+X*/2 461 277+X* 178 320 125 100 335 1.5 200 61 235 9) 61

220 6) 140/160 326 637 814 200 407+X*/2 507 307+X* 180 370 160 125 385 1.5 235 71 270 71

250 160/180 326 650 840 210 420+X*/2 525 315+X* 180 410 160 125 425 1.5 250 71 300 9) 71

280 6) 180/200 375 752 955 241 477.5+X*/2 598 357+X* 220 460 200 160 480 2 295 88 325 88

320 200/220 391 760 955 245 477.5+X*/2 600 355+X* 220 510 200 160 530 2 320 88 365 9) 88

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

Ø R

A

VE

5)EE

Ø D

A

KK

Ø M

M

Ø D

WA

A

PJ + X*10)Y

Ø D42)

EENV

G 1

/41)

Ø D42)

Ø R

A

VE

X1 X1

US

Ø SB

LHL1

TS

ST

XS

ZB + X*10)

SS + X*10)

S1

S S

S1

12)

5)EE

Ø D

A

KK

Ø M

M

Ø D

WA

A

PK + X*10)Y

Ø D42)

EENV

G 1

/41)

Ø D42)

Ø R

A

VE

X1 X1

WA + X*

VE

Ø R

A

US

Ø SB

LHL1

TS

ST

XS

ZM + 2 x X*10)

SS + X*10)

S1

S S

S1

12)

Ø R

A

Ø R

A

VE VE


Foot mounting MS2

CGH2 MS211): for seal versions „A”, „B” and AL-Ø 160 - 320 mm

CDH2 MS211): for seal versions „A”, „B” and AL-Ø 160 - 320 mm

CDH2 MS22), 11)

CGH2 MS211)

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Dimensions MS2 (dimensions in mm)

AL = Piston Ø

MM = Piston rod Ø




pages 18 and 19

5) = Throttle valve only for end position cushioning "E" (180° to the bleed point)

6) = Piston Ø not standardised7) = Dimensions for cylinder with seal versions M, T and S8) = Dimensions for cylinder with seal versions A and B9) = Tolerance: f810) = Take the minimum stroke length „X*min.” into account11) = Not standardised12) = 2 mm deep counter bore for the DIN 912 S.H.C.S.

The screws must not be subjected to shear loads. The forces have to be distributed by keys

AL Ø

MM Ø

KK A NV D DA D4 2)

EE 7)

EE 7)

Y PJ X1 WA

40 6) 25/28 M20x1.5 28 19/22 88 50 34 G1/2 M22x1.5 83 120 41 18

50 32/36 M27x2 36 27/30 102 60 34 G1/2 M22x1.5 98 120 48.5 18

63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21

80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24

100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27

125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31

140 6) 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31

160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35

180 6) 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40

200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40

220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42

250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42

280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48

320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48

AL Ø

MM Ø

PK XS ZB max.

ZM SS X*10)

min.S S1 SB

H13ST TS

js13US Ø-1

LH L1 RA7) f8

VE7) RA8) VE8)

40 6) 25/28 120 118 230 286 50 1 30 15 11 32 110 135 45 89 52 29 88 –

50 32/36 120 135.5 244 316 45 1 35 17.5 11 37 130 155 55 106 63 29 102 –

63 40/45 133 154 274 357 49 1 40 20 13.5 42 150 180 65 125 75 32 120 –

80 50/56 155 171.5 305 395 52 2 50 25 17.5 47 180 220 75 147.5 90 36 145 –

100 63/70 171 189 340 439 61 3 60 30 22 57 210 255 90 175 110 41 170 –

125 80/90 205 218 396 511 75 1 70 35 26 67 255 305 105 208 132 45 206 –

140 6) 90/100 219 240.5 430 551 70 19 85 42.5 30 72 290 350 115 228 145 45 226 –

160 100/110 235 270 467 605 65 44 105 52.5 33 77 330 400 135 267.5 160 50 200 9) 50

180 6) 110/125 264 291.5 510 652 69 50 115 57.5 40 92 360 440 150 296 185 55 220 9) 55

200 125/140 278 322.5 550 718 73 56 125 62.5 40 97 385 465 160 313 200 61 235 9) 61

220 6) 140/160 326 369.5 637 814 75 100 155 77.5 45 102 445 530 185 362.5 235 71 270 71

250 160/180 326 382.5 650 840 75 100 155 77.5 52 112 500 600 205 402.5 250 71 300 9) 71

280 6) 180/200 375 415.5 752 955 124 51 155 77.5 52 142 550 650 235 457.5 295 88 325 88

320 200/220 391 435 760 955 85 125 190 95 62 142 610 730 255 500 320 88 365 9) 88

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

PJ + X*

X1

YX1

X1 X1

Y PK + X*

w

c Ød 3

d1

w

w Ød 3

d1


Flange connections

CDH2

CGH2

Porting pattern for rectangular flanges to ISO 6162 table 1 (=̂ SAE 3000 PSI) and table 2 (=̂ SAE 6000 PSI)

Porting pattern for square flanges to ISO 6164 tables 1 and 2

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Flange connections (dimensions in mm)

For main dimensions see pages 6 to 17

AL = Piston Ø

X* = Stroke length1) = Thread depth for seal versions M, T and S2) = Thread depth for seal versions A and B3) = Max. operating pressure for associated flanges in bar4) = Flange porting pattern to ISO 6162 Tab.1 relates to a

flange porting pattern to SAE 3000 PSI5) = Flange porting pattern to ISO 6162 Tab.2 relates to a

flange porting pattern to SAE 6000 PSI

AL Version „F“

ISO 6162 Tab.1 (200 - 350 bar) (=̂ SAE 3000 PSI)

Version „K“

ISO 6164 Tab.1 (250 bar)

Ø Y PJ PK

X1 d3 Ø

d34)

Øc

±0.25

w ±0.25

d1 t11) t1

2) p3) Y PJ PK

X1 d3 Ø

w ±0.25

d1 t11) t1

2) p3)

40 – – – – – – – – – – – 82 122 40.5 10 24.7 M6 12.5 10 250

50 – – – – – – – – – – – 97 122 48 10 24.7 M6 12.5 12.5 250

63 111 135 55 13 1/2“ 38.1 17.5 M8 16 16 350 111 135 57 13 29.7 M8 16 16 250

80 123.5 148 68 13 1/2“ 38.1 17.5 M8 16 16 350 123.5 148 69.5 13 29.7 M8 16 16 250

100 133 173 79 19 3/4“ 47.6 22.3 M10 20 20 350 133 173 81,5 19 35.4 M8 16 16 250

125 153 205 98 25 1“ 52.4 26.2 M10 20 20 350 157 197 100 19 35.4 M8 16 16 250

140 162 227 107 32 1 1/4“ 58.7 30.2 M10 20 20 250 162 227 109 25 43.8 M10 20 20 250

160 181.5 242 127 32 1 1/4“ 58.7 30.2 M10 20 20 250 181.5 242 128.5 25 43.8 M10 20 20 250

180 193 266 139 38 1 1/2“ 69.9 35.7 M12 24 24 200 194 264 142 32 51.6 M12 24 24 250

200 219 280 146,5 38 1 1/2“ 69.9 35.7 M12 24 24 200 220 278 148.5 32 51.6 M12 24 24 250

AL Version „D“

ISO 6162 Tab.2 (400 bar) (=̂ SAE 6000 PSI)

Version „H“

ISO 6164 Tab.2 (400 bar)

Ø Y PJ PK

X1 d3 Ø

d35)

Øc

±0.25

w ±0.25

d1 t11) t1

2) p3) Y PJ PK

X1 d3 Ø

w ±0.25

d1 t11) t1

2) p3)

40 – – – – – – – – – – – 82 122 40.5 10 24.7 M6 12.5 10 400

50 – – – – – – – – – – – 97 122 48 10 24.7 M6 12.5 12.5 400

63 – – – – – – – – – – – 111 135 57 13 29.7 M8 16 16 400

80 120 155 67 13 1/2“ 40.5 18.2 M8 16 14 400 123.5 148 69.5 13 29.7 M8 16 16 400

100 134 171 80.5 13 1/2“ 40.5 18.2 M8 16 16 400 133 173 81.5 19 35.4 M8 16 16 400

125 153 205 97 19 3/4“ 50.8 23.8 M10 20 20 400 157 197 100 19 35.4 M8 16 16 400

140 162 227 107 25 1“ 57.2 27.8 M12 24 24 400 162 227 109 25 43.8 M10 20 20 400

160 181.5 242 127 25 1“ 57.2 27.8 M12 24 24 400 181.5 242 128.5 25 43.8 M10 20 20 400

180 194 264 139.5 32 1 1/4“ 66.6 31.8 M14 26 26 400 194 264 142 32 51.6 M12 24 24 400

200 220 278 147 32 1 1/4“ 66.6 31.8 M14 26 26 400 220 278 148.5 32 51.6 M12 24 24 400

220 244 326 168 38 1 1/2“ 79.3 36.5 M16 30 30 400 244 326 171 38 60.1 M16 30 30 400

250 257 326 189 38 1 1/2“ 79.3 36.5 M16 30 30 400 257 326 192 38 60.1 M16 30 30 400

280 290 375 215 38 1 1/2“ 79.3 36.5 M16 30 30 400 290 375 218 38 60.1 M16 30 30 400

320 282 391 236 51 2“ 96.8 44.5 M20 36 36 400 282 391 240 51 69.3 M16 30 30 400

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

L5ZB + X*

D1

ØD

2

L4ZP + X*

NFL6

ØD

2

L6

L4

D1

D1

L3

L5ZB + X*

D1

L5ZB + X*

D1

XC / XO + X*

L2

H


MP3, MP5

MF3

MF4: AL-Ø 40 - 80 mm MF4: AL-Ø 100 - 320 mm

MT4

MS2

Position measuring system

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om



AL = Piston Ø

MM = Piston rod Ø

X* = Stroke length

X*max = Max. stroke length1) = Centering ring BA cannot be used

Position measuring system (dimensions in mm)

AL Ø

MM Ø

X*max XC XO H ZB ZP NF js13

L2 L3 L4 L5 L6 D1 max

D2 Ø

40 – 28

1400 447 447 115 239 262 28 124 – 3 166 166 80 18

50 32 36

1400 470 470 120 254 278 28 132 – 3 166 166 96 20

63 40 45

2000 526 526 130 299 313 28 150 – 0 166 166 96 0

80 50 56

2000 580 580 125 332,5 350 32 176.5 – 0 166 166 96 0

100 63 70

3000 617 617 135 362 390 36 192 8 0 166 138 96 0

125 80 90

3000 693 693 145 410 445 55 227 20 21.5 166 131 96 33

140 90 100

3000 755 755 155 440 485 60 262 15 25.5 166 121 96 40

160 100 110

3000 787 787 165 472.5 525 65 269.5 12.5 25.5 166 113.5 96 40

180 110 125

3000 855 855 175 510 570 70 307 10 32 166 106 96 48

200 125 140

3000 926 926 190 550 616 76 333 10 32 166 100 96 48

220 140 160

3000 1100 1100 205 637 715 88 418 10 38 166 88 96 57

250 160 180

3000 1115 1115 220 650 730 90 420 10 38 166 86 96 57

280 180 200

3000 1295 1295 280 752 857 115 510 10 44 166 61 96 66

320 200 220

3000 1300 1300 300 760 865 115 520 10 44 166 61 96 66

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om



The contactless, absolute position measuring system is rated up to 500 bar. Its function principle is based on the magneto-strictive effect. In connection with this, a torsion impulse is triggered off when two magnetic fields meet. This impulse is directed from the point of measurement via the wave guide inside the measuring scale to the sensor head. The transmission time is constant and virtually independent of temperature. It is proportional to the position of the magnet and can therefore be used as a reference for the actual position value and is converted into a direct analogue of digital output in the sensor head.

Technical data (for applications outside these parameters, please consult us!)

Operating pressure bar 250

Analogue output V 0 to 10

Load resistance kΩ ≥ 5

Resolution Infinite

Analogue output mA 4 to 20

Load resistance Ω 0 to 500

Resolution Infinite

Digital output SSI 24 Bit grey coded

Resolution μm 5

Measuring direction Forwards

Linearity (absolute accuracy)

Analogue % mm

≤ ±0.02 % (with reference to the measurement length) min. ±0.05

Digital % mm

≤ ±0.01 % (with reference to the measurement length) min. ±0.04

Repeatability % mm

±0.001 (with reference to the measurement length) min. ±0.0025

Hysteresis mm ≤ 0.004

Supply voltage V DC 24 (± 10 % with an analogue output)

Current consumption mA 100

Residual ripple % s-s ≤ 1

Current consumption

V DC mA

24 (+ 20 %/– 15 % with a digital output) 70

Residual ripple % s-s ≤ 1

Protection Tube and flange IP 67

Sensor electronics IP 65

Operating temperture Sensor electronics °C – 40 to + 75

Temperature co-efficient Voltage ppm/°C 70

Current ppm/°C 90

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

2 1

3 6

4 5

6

14

2

7

35

1)

1)



MF3, MF4, MT4, MS2

1) For analogue output: 6-pin Amphenol - Plug-in connector Material No. R900072231 (plug-in connector is not included within the scope of supply, it must be ordered separately)

Position measuring system (analogue output) Component plug (viewed on the pin side)

Position measuring system (digital output) Component plug (viewed on the pin side)

Mounting style

1) For digital output: 7-pin Amphenol - Plug-in connector Material No. R900079551 (plug-in connector is not included within the scope of supply, it must be ordered separately)

Connection allocation

Pin Cable Signal / current Signal / voltage

1 grey 4...20 mA 0 - 10 V

2 pink Gnd Gnd

3 yellow n. c. 10 - 0 V

4 green n. c. Gnd

5 brown +24 V DC (±10%) +24 V DC (±10%)

6 white Gnd Gnd

Pin Cable Signal / SSi

1 grey data (–)

2 pink data(+)

3 yellow tact (+)

4 green tact (–)

5 brown +24 V DC (+20%/–15%)

6 white 0 V

7 – n. c.

MP3, MP5

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

X4

L7

X3

PL + X*

1) 1)

L7

X3

PM + X*

1) 1)

X5 3)


Proximity switch

CDH2

CGH2

Plug-in connector with a 5 m cable Material No. R900026512 (plug-in connector is not included with the scope of supply, it must be ordered separately)

Plug-in connector, angled with a 5 m cable (the orientation of the cable exit is not definable) Material No. R900021404 (plug-in connector is not included with the scope of supply, it must be ordered separately)

Mounting styles

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Proximity switch (dimensions in mm)


AL = Piston Ø

MM = Piston rod Ø

X* = Stroke length1) = The proximity switch is always located

opposite to the pipe connection2) = Piston Ø 220 - 320 mm,

the proximity switch does not overhang3) = Piston Ø 220 - 320 mm,

the angled plug-in connector is not possible

AL Ø

MM Ø

PL PM L7 X3 X4 X5

40 25 28

112 112 87 94 170 125

50 32 36

110 110 103 98 175 130

63 40 45

125 125 116 103 180 135

80 50 56

138 138 128,5 108 185 140

100 63 70

161 161 139 116 195 150

125 80 90

189 189 161 126 205 160

140 90 100

209 209 171 146 225 180

160 100 110

228 228 188,5 151 230 185

180 110 125

254 254 199 159 235 190

200 125 140

264 264 227 166 245 200

220 140 160

310 310 252 177 2) 255 – 3)

250 160 180

310 310 265 187 2) 265 – 3)

280 180 200

369 369 293 199 2) 275 – 3)

320 200 220

375 375 290 209 2) 285 – 3)

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

+

–

1

4

3

12

34

G1/4

38

Ø 20

M16x2

SW19


Technical data (for applications outside these parameters, please consult us!)Function PNP N/O

Permissible pressure bar 500

Operating pressure V DC 10 … 30

Including the residual ripple % ≤ 15

Voltage drop V ≤ 1.5

Rated operating voltage V DC 24

Rated operating current mA 200

No load current mA ≤ 8

Residual current μA ≤ 10

Repeatability % ≤ 5

Hysteresis % ≤ 15

Ambient temperture range °C – 25 … + 80

Temperature drift % ≤ 10

Switching frequency Hz 1000

Protection Active area IP 68 to DIN 40050

Proximity switch IP 67 to DIN 40050

Housing material Material No. 1.4104

Proximity switch

Inductive proximity switches are used as a reliable end position control for hydraulic cylinders. They are an important element, in providing safety systems, interlocks and/or other machine functions where signals safely and exactly monitor the end position. The up to 500 bar rated high pressure proximity switches operate without contact and contacts and are, there-

Connection allocation2)

1)

3)

1) Brown2) Black3) Blue

For pressure measurement or bleeding. For installation in the bleed/measuring port. Coupling with check valve function, i.e. it can also be connected when pressure is present.

Scope of supply:

Coupling AB 20-11/K1 with NBR seal Material No. R900009090 Coupling AB 20-11/K1 V with FKM seal Material No. R900001264

Coupling (dimensions in mm)

fore wear-free. Due to safety reasons the proximity switch is protected against being screwed in too deep. The switching distance can, therefore not be adjusted. For the version with proximity switches (Option 1 „E“), the cylinders are fitted with proximity switches on each end.

A/F

19

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

EN

EU

CHLF

1)

3)KK

AV

N

Z

ØCN

Z

2)

EF

MA


Self-aligning clevis CGKD (dimensions in mm)

ISO 6982

DIN 24338

ISO 8132

Series CDH2 Type Material no. Nominal force

N

AV

min.

N

max.

CH

js13

EF

max.

CN

H7

EN

h12

EU

max.AL Ø

MM Ø

40 25 / 28 CGKD 25 R900323332 32.000 29 31 65 32 25 25 2250 32 / 36 CGKD 32 R900322049 50.000 37 38 80 40 32 32 2863 40 / 45 CGKD 40 R900322029 80.000 46 47 97 50 40 40 3480 50 / 56 CGKD 50 R900322719 125.000 57 58 120 63 50 50 42100 63 / 70 CGKD 63 R900322028 200.000 64 70 140 72,5 63 63 53,5125 80 / 90 CGKD 80 R900322700 320.000 86 91 180 92 80 80 68140 90 / 100 CGKD 90 R900325702 400.000 91 100 195 101 90 90 72160 100 / 110 CGKD 100 R900322030 500.000 96 110 210 114 100 100 85,5180 110 / 125 CGKD 110 R900308153 635.000 106 125 235 129 110 110 88200 125 / 140 CGKD 125 R900322026 800.000 113 135 260 160 125 125 105220 140 / 160 CGKD 160 R900300718 1.520.000 126 165 310 200 160 160 133250 160 / 180 CGKD 160 R900300718 1.520.000 126 165 310 200 160 160 133280 180 / 200 CGKD 200 R900324814 2.000.000 161 215 390 250 200 200 165320 200 / 220 CGKD 200 R900324814 2.000.000 161 215 390 250 200 200 165

Series CDH2 Type KK LF

min.

Z Clamping screw

ISO 4762-10.9

MA3)

Nm

m 4)

kgAL Ø

MM Ø

40 25 / 28 CGKD 25 M20 x 1,5 25,5 2° M8 x 20 25 0,6550 32 / 36 CGKD 32 M27 x 2 30 4° M10 x 25 49 1,1563 40 / 45 CGKD 40 M33 x 2 39 4° M10 x 30 49 2,180 50 / 56 CGKD 50 M42 x 2 47 4° M12 x 35 86 4100 63 / 70 CGKD 63 M48 x 2 58 4° M16 x 40 210 7,2125 80 / 90 CGKD 80 M64 x 3 74 4° M20 x 50 410 15140 90 / 100 CGKD 90 M72 x 3 85 4° M20 x 60 410 19160 100 / 110 CGKD 100 M80 x 3 94 4° M24 x 60 710 25,5180 110 / 125 CGKD 110 M90 x 3 105 4° M24 x 60 710 36,5200 125 / 140 CGKD 125 M100 x 3 116 4° M24 x 70 710 52,5220 140 / 160 CGKD 160 M125 x 4 145 4° M 24 x 80 710 82,5250 160 / 180 CGKD 160 M125 x 4 145 4° M 24 x 80 710 82,5280 180 / 200 CGKD 200 M160 x 4 190 4° M30 x 100 1500 168320 200 / 220 CGKD 200 M160 x 4 190 4° M30 x 100 1500 168

AL = Piston Ø

MM = Piston rod Ø1) = Grease nipple, cone head form A according to

DIN 714122) = Associated pin Ø r6

Note:

The geometry and dimensions may vary depending on the make.

For combination with other mounting elements, the usability must be verified.

3) = The self-aligning clevis must always be screwed to the piston rod thread stop. Subsequently, the clamping screws have to be tight-ened to the specified torque.

4) = Weight of the self-aligning clevis

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

1); 5)

CL2

CL1

CM

KK

LE

CE

Ø C

K

3)MAb

2)

ER

CV


Fork clevis CCKB (dimensions in mm)

ISO 8132


N

b

max.

CE

js13

CK

H9

CL1

h16

CL2

max.

CM

A13

ER

max.

AL

Ø

MM

Ø

40 25 / 28 CCKB 25 R900542845 32.000 50 65 25 56 84 25 32

50 32 / 36 CCKB 32 R900542846 50.000 65 80 32 70 105 32 40

63 40 / 45 CCKB 40 R900542847 80.000 80 97 40 90 133 40 50

80 50 / 56 CCKB 50 R900542848 125.000 100 120 50 110 165 50 63

100 63 / 70 CCKB 63 R900542849 200.000 140 140 63 140 185 63 71

125 80 / 90 CCKB 80 R900542850 320.000 180 180 80 170 225 80 90

140 90 / 100 CCKB 90 8) 400.000 200 195 90 190 8) 90 100

160 100 / 110 CCKB 100 8) 500.000 220 210 100 210 8) 100 110

Series CDH2 Type KK LE

min.

CV

max.

Clamping screw

ISO 4762-10.9

MA3)

Nm

m 4)

kg

AL

Ø

MM

Ø

40 25 / 28 CCKB 25 M20 x 1,5 34 32 M10 x 35 49 1,4

50 32 / 36 CCKB 32 M27x 2 42 40 M12 x 40 85 2,8

63 40 / 45 CCKB 40 M33 x 2 52 50 M16 x 50 210 5,2

80 50 / 56 CCKB 50 M42 x 2 64 63 M20 x 60 425 9,5

100 63 / 70 CCKB 63 M48 x 2 75 71 M24 x 80 730 21,5

125 80 / 90 CCKB 80 M64 x 3 94 90 M30 x 100 1450 38,2

140 90 / 100 CCKB 90 M72 x 3 109 100 M36 x 120 2480 8)

160 100 / 110 CCKB 100 M80 x 3 120 110 M36 x 130 2480 8)

AL = Piston Ø

MM = Piston rod Ø1) = Grease nipple, cone head form A according to

DIN 714122) = Associated pin Ø m6

(pins and pin securing rings are included within the scope of supply and not mounted at the point in time of the supply)

3) MA = Tightening torque The fork clevis must always be screwed to the piston rod thread stop. Subsequently, the clamping screws have to be tightened to the specified torque.

4) m = Weight of the fork clevis8) = Upon request

Note:

The geometry and dimensi-ons may vary depending on the make.

For combination with other mounting elements, the usabili-ty must be verified.

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

3)

l3 x

45ϒ

FSN

H

"A"

"A"

l1

CR

Ø HB

KC

CO

TH

UL

FNFK

l2

A0,05

A

1)


ISO 8132

Series CDH2

Type Material no. Nominal force

N

CR

H7

CO

N9

FK

js12

FN

max.

FS

js14

HB

H13

KC

+0,3

AL Ø

40 CLTB 25 R900772610 4) 32.000 25 25 55 80 12 13,5 5,4

50 CLTB 32 R900772611 4) 50.000 32 25 65 100 15 17,5 5,4

63 CLTB 40 R900772612 4) 80.000 40 36 76 120 16 22 8,4

80 CLTB 50 R900772613 4) 125.000 50 36 95 140 20 26 8,4

100 CLTB 63 R900772614 4) 200.000 63 50 112 180 25 33 11,4

125 CLTB 80 R900772615 4) 320.000 80 50 140 220 31 39 11,4

140 CLTB 90 8); 4) 385.000 90 63 160 250 40 45 12,4

160 CLTB 100 8); 4) 500.000 100 63 180 280 45 52 12,4

180 CLTB 110 8); 4) 630.000 110 80 200 310 50 52 15,4

200 CLTB 125 8); 4) 785.000 125 80 220 345 56 45 15,4

Series CDH2

Type l1

l2

l3

NH

max.

TH

js14

UL

max.

m 2)

kgAL Ø

40 CLTB 25 56 45 1,5 26 80 110 2,1

50 CLTB 32 70 52 2 33 110 150 4,55

63 CLTB 40 88 60 2,5 41 125 170 7,3

80 CLTB 50 105 75 2,5 51 160 210 14,5

100 CLTB 63 130 85 3 61 200 265 23,1

125 CLTB 80 170 112 3,5 81 250 325 52,3

140 CLTB 90 8) 8) 3,5 91 265 345 8)

160 CLTB 100 215 8) 3,5 102 295 385 8)

180 CLTB 110 8) 8) 8) 112 320 410 8)

200 CLTB 125 8) 8) 8) 132 385 570 8)

AL = Piston Ø1) = Grease nipple, cone head form A ac-

cording to DIN 714122) m = Weight of the trunnion bracket (indica-

tion per pair) 3) = Contact surface of the trunnion (in-

side face)4) = Mounting blocks are always supplied

in pairs8) = Upon request

Trunnion bracket CLTB (dimensions in mm)

Note:



Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

3)

Ø S

Ø HB

COFOFGKC

RG

UX

MR

1

Ø C

K

SL

CL KL

CM

RF

UK

LE

FL


ISO 8132, Form B


N

CK

H9

CL

h16

CM

A12

CO

N9

FG

js14

FL

js12

FO

js14

HB

H13

KC

+0,3

KL LE

min.AL Ø

MM Ø

40 25 / 28 CLCA 25 R900542864 32.000 25 56 25 25 10 55 10 13,5 5,4 10 3750 32 / 36 CLCA 32 R900542865 50.000 32 70 32 25 14,5 65 6 17,5 5,4 13 4363 40 / 45 CLCA 40 R900542866 80.000 40 90 40 36 17,5 76 6 22 8,4 16 5280 50 / 56 CLCA 50 R900542867 125.000 50 110 50 36 25 95 0 26 8,4 19 65100 63 / 70 CLCA 63 R900542868 200.000 63 140 63 50 33 112 0 33 11,4 20 75125 80 / 90 CLCA 80 R900542869 320.000 80 170 80 50 45 140 0 39 11,4 26 95140 90 / 100 CLCA 90 8) 400.000 90 190 90 63 47,5 160 0 45 12,4 28 108160 100 / 110 CLCA 100 8) 500.000 100 210 100 63 52,5 180 0 52 12,4 30 120180 110 / 125 CLCA 110 8) 635.000 110 240 110 80 62,5 200 0 52 15,4 31 138200 125 / 140 CLCA 125 8) 800.000 125 270 125 80 75 230 0 52 15,4 32 170

Series CDH2 Type MR

max.

RF

js14

RG

js14

S SL UK

max.

UX

max.

m 4)

kgAL Ø

MM Ø

40 25 / 28 CLCA 25 25 90 85 20 69 120 115 350 32 / 36 CLCA 32 32 110 110 26 87 145 145 563 40 / 45 CLCA 40 40 140 125 33 110 185 170 9,680 50 / 56 CLCA 50 50 165 150 40 133 215 200 15,5100 63 / 70 CLCA 63 63 210 170 48 164 270 230 27,5125 80 / 90 CLCA 80 80 250 210 57 202 320 280 47140 90 / 100 CLCA 90 90 280 235 66 224 360 320 8)

160 100 / 110 CLCA 100 100 315 250 76 246 405 345 8)

180 110 / 125 CLCA 110 110 335 305 76 277 425 400 8)

200 125 / 140 CLCA 125 125 365 350 76 310 455 450 8)

AL = Piston Ø

MM = Piston rod Ø3) = Associated pin Ø m6

(pins and pin securing rings are included within the scope of supply and not mounted at the point in time of the supply)

4) m = Weight of the clevis bracket8) = Upon request

Clevis bracket CLCA (dimensions in mm)

Note:



Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

3)

SL

CL KL

CM

UR

RC

Ø C

K

FL

LE

UH

TB

Ø S

Ø HB

MR

1


ISO 8132, Form A


N

CK

H9

CL

h16

CM

A12

FL

js12

HB

H13

KL LE

min.

MR

max.

RC

js14

S

AL Ø

MM Ø

40 25 / 28 CLCD 25 R900542882 32.000 25 56 25 55 13,5 10 37 25 40 20

50 32 / 36 CLCD 32 R900542883 50.000 32 70 32 65 17,5 13 43 32 50 26

63 40 / 45 CLCD 40 R900542884 80.000 40 90 40 76 22 16 52 40 65 33

80 50 / 56 CLCD 50 R900542885 125.000 50 110 50 95 26 19 65 50 80 40

100 63 / 70 CLCD 63 R900542886 200.000 63 140 63 112 33 20 75 63 100 48

125 80 / 90 CLCD 80 R900542887 320.000 80 170 80 140 39 26 95 80 125 57

140 90 / 100 CLCD 90 8) 400.000 90 190 90 160 45 28 108 90 140 66

160 100 / 110 CLCD 100 8) 500.000 100 210 100 180 52 30 120 100 160 76

180 110 / 125 CLCD 110 8) 635.000 110 240 110 200 52 31 138 110 180 76

200 125 / 140 CLCD 125 8) 800.000 125 270 125 230 52 32 170 125 200 76

Series CDH2 Type SL TB

js14

UR

max.

UH

max.

m 4)

kgAL Ø

MM Ø

40 25 / 28 CLCD 25 69 85 70 113 1,9

50 32 / 36 CLCD 32 87 110 85 143 3

63 40 / 45 CLCD 40 110 130 108 170 5,5

80 50 / 56 CLCD 50 133 170 130 220 10,6

100 63 / 70 CLCD 63 164 210 160 270 17

125 80 / 90 CLCD 80 202 250 210 320 32

140 90 / 100 CLCD 90 224 290 230 370 8)

160 100 / 110 CLCD 100 246 315 260 400 8)

180 110 / 125 CLCD 110 277 350 290 445 8)

200 125 / 140 CLCD 125 310 385 320 470 8)

AL = Piston Ø

MM = Piston rod Ø3) = Associated pin Ø m6

(pins and pin securing rings are in-cluded within the scope of supply and not mounted at the point in time of the supply)

4) m = Weight of the clevis bracket8) = Upon request

Clevis bracket CLCD (dimensions in mm)

Note:



Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

1)

1)

1)

L

L

L L

L

L

L

L


The permissible stroke length with a flexibly guided load and a 3.5 safety factor against buckling can be obtained from the ap-propriate table. With a deviating cylinder installation, the per-missble stroke length has to be interpolated. Permissible stroke lengths for non-guided loads are available on request.

The calculation for buckling are carried out as follows:

1. Calculation according to Euler

2. Calculation according to Tetmajer

A

LK = 0,7 L

CB

LK = L LK = 2 L

π2 • E • IF = if λ > λg ν • LK

2

d2 • π (335–0.62 • λ)F = if λ ≤ λg 4 • ν

Buckling

The influence of the mounting style on the buckling length:

Permissible stroke lengths (dimensions in mm)

AL MM Permissible stroke lengths at Max. available

stroke lengthsInstallationØ Ø 100 bar 160 bar 250 bar

0° 45° 90° 0° 45° 90° 0° 45° 90°

40 25 28

195 385

200 400

215 445

130 295

135 300

140 320

40 215

45 220

55 225 0°

50 32 36

380 505

390 525

430 595

280 395

285 405

300 430

195 290

200 295

205 305

200063 40

45480 640

500 660

550 750

365 505

370 515

385 550

255 380

260 385

265 395

80 50 56

590 765

615 800

690 930

455 615

465 630

495 685

330 470

335 475

345 495

100 63 70

750 940

780 985

910 1195

595 775

610 800

660 885

445 605

455 615

470 650

125 80 90

970 1235

1015 1300

1200 1610

780 1030

805 1070

880 1200

595 825

605 840

635 895 45°

140 90 100

1075 1335

1130 1405

1360 1770

875 1120

905 1165

1000 1325

675 900

685 920

725 985

3000160 100

1101175 1430

1230 1500

1480 1875

955 1195

985 1240

1085 1400

735 955

750 975

785 1040

180 110 125

1250 1620

1310 1710

1570 2160

1010 1365

1045 1420

1150 1620

775 1100

790 1125

830 1205

200 125 140

1435 1795

1510 1900

1860 2450

1180 1525

1220 1590

1365 1840

915 1240

935 1270

990 1370

220 140 160

1620 2075

1710 2200

2180 3000

1360 1810

1415 1890

1630 2280

1090 1510

1120 1560

1200 1730 90°

250 160 180

1805 2250

1910 2395

2490 3300

1520 1960

1590 2060

1850 2500

1220 1630

1250 1690

1360 1880

6000280 180

2002075 2510

2200 2670

2900 3700

1775 2200

1880 2310

2170 2820

1450 1850

1490 1920

1620 2140

320 200 220

2135 2550

2270 2720

3030 3820

1820 2230

1900 2340

2260 2880

1470 1860

1510 1930

1660 2170

1) Perm. stroke length

Mounting styles MP3, MP5

Explanation:

E = Modulus of elasticity in N/mm2

= 2.1 x 105 for steell = Moment of inertia in mm4 for a circular cross- section area

ν = 3.5 (safety factor)LK = Free buckling length in mm (dependent on the mounting style, see sketches A, B, C)d = Piston rod Ø in mmλ = Slenderness ratio 4 • LK E = λg = π d 0.8 • ReRe = Yield strength of the piston rod material

d 4 • π = = 0.0491 • d 4 64

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

1)

1)

1)1)

1)

1)


Permissible stroke lengths (dimensions in mm)Mounting style: MF3

Mounting style: MF4



0° 45° 90° 0° 45° 90° 0° 45° 90°

40 25 28

895 1400

915 1415

980 1630

730 1180

735 1205

760 1275

440 970

450 980

510 1010 0°

50 32 36

1440 1760

1490 1830

1670 2000

1210 1510

1230 1545

1300 1675

985 1255

995 1270

1025 1320

200063 40

451735 2000

1800 2000

2000 2000

1475 1830

1510 1880

1620 2080

1215 1540

1230 1560

1270 1640

80 50 56

2000 2000

2000 2000

2000 2000

1810 2000

1850 2000

1995 2000

1495 1870

1515 1900

1570 2000

100 63 70

2580 3000

2690 3000

3000 3000

2235 2690

2300 2780

2550 3000

1875 2300

1910 2350

2010 2520

125 80 90

3000 3000

3000 3000

3000 3000

2840 3000

2930 3000

3000 3000

2400 3000

2450 3000

2590 3000 45°

140 90 100

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

2700 3000

2760 3000

2950 3000

3000160 100

1103000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

2920 3000

2980 3000

3000 3000

180 110 125

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

200 125 140

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

220 140 160

5400 6000

5680 6000

6000 6000

4800 5820

4980 6000

5780 6000

4120 5150

4220 5330

4560 6000 90°

250 160 180

5850 6000

6000 6000

6000 6000

5270 6000

5500 6000

6000 6000

4600 5650

4740 5850

5250 6000 6000

280 180 200

6000 6000

6000 6000

6000 6000

6000 6000

6000 6000

6000 6000

5270 6000

5420 6000

5970 6000

320 200 220

6000 6000

6000 6000

6000 6000

6000 6000

6000 6000

6000 6000

5950 6000

6000 6000

6000 6000


AL MM Permissible stroke lengths at Max. available stroke lengths

InstallationØ Ø 100 bar 160 bar 250 bar0° 45° 90° 0° 45° 90° 0° 45° 90°

40 25 28

325 565

340 590

370 695

245 465

250 475

260 520

105 365

110 370

140 385 0°

50 32 36

600 755

625 790

715 950

485 630

495 650

530 715

370 505

375 515

390 540

200063 40

45730 920

765 965

905 1190

600 780

615 805

675 905

470 630

480 645

500 685

80 50 56

910 1125

950 1185

1130 1470

750 960

775 990

845 1120

595 785

605 800

630 850

100 63 70

1120 1350

1175 1430

1460 1860

945 1175

980 1220

1105 1420

770 980

785 1000

835 1090

125 80 90

1430 1750

1510 1855

1910 2490

1225 1540

1270 1610

1450 1910

1000 1300

1025 1340

1100 1470 45°

140 90 100

1585 1895

1675 2010

2170 2750

1370 1675

1425 1755

1650 2110

1135 1425

1165 1470

1260 1630

3000160 100

1101725 2030

1820 2150

2340 2900

1490 1785

1545 1870

1780 2230

1230 1510

1260 1560

1360 1720

180 110 125

1855 2300

1960 2440

2510 3350

1595 2040

1660 2130

1910 2580

1315 1735

1350 1790

1450 1990

200 125 140

2105 2535

2230 2700

2950 3000

1830 2260

1910 2370

2250 2920

1530 1940

1570 2010

1715 2255

220 140 160

2250 2800

2400 2990

3350 4500

1990 2530

2090 2680

2550 3480

1685 2220

1740 2310

1950 2700 90°

250 160 180

2600 3130

2770 3350

3900 5050

2310 2840

2430 3000

3000 3910

1975 2500

2040 2600

2300 3040

6000280 180

2002850 3370

3050 3610

4400 5550

2550 3070

2680 3250

3370 4300

2190 2700

2270 2820

2600 3330

320 200 220

3070 3560

3270 3820

4750 5850

2750 3250

2890 3430

3650 4550

2150 2860

2460 2980

2810 3530


Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

1)

1)

1)

1)

1)

1)

1)

1) 1)


Permissible stroke lengths (dimensions in mm)Mounting style: MT4 (trunnion located in the middle of the cylinder)

Mounting style: MS2



0° 45° 90° 0° 45° 90° 0° 45° 90°

40 25 28

340 590

345 605

365 665

250 470

255 480

260 500

130 365

135 370

145 375 0°

50 32 36

600 770

615 795

670 890

470 625

480 635

495 670

355 485

360 490

365 505

200063 40

45740 940

765 975

845 1115

590 770

600 790

630 845

450 610

455 620

465 640

80 50 56

920 1155

950 1195

1055 1375

735 950

750 975

790 1045

570 755

575 765

590 790

100 63 70

1145 1400

1190 1460

1365 1740

940 1180

960 1210

1030 1330

740 955

750 970

775 1015

125 80 90

1470 1820

1530 1910

1780 2320

1220 1550

1250 1600

1350 1780

970 1275

985 1300

1020 1370 45°

140 90 100

1640 1980

1710 2080

2020 2570

1370 1700

1410 1755

1540 1970

1100 1400

1120 1430

1170 1515

3000160 100

1101780 2110

1850 2210

2180 2710

1485 1800

1520 1860

1660 2080

1190 1480

1210 1510

1260 1595

180 110 125

1910 2405

1990 2530

2340 3000

1590 2065

1635 2130

1780 2400

1275 1710

1295 1740

1350 1850

200 125 140

2180 2660

2280 2800

2740 3000

1840 2300

1890 2380

2090 2720

1490 1915

1510 1960

1590 2100

220 140 160

2490 3000

2510 3170

3150 4230

2050 2640

2120 2750

2400 3260

1685 2240

1720 2310

1835 2530 90°

250 160 180

2730 3320

2870 3520

3640 4720

2350 2940

2440 3060

2790 3650

1950 2500

1990 2570

2140 2830

6000280 180

2003040 3620

3210 3840

4140 5210

2640 3210

2750 3360

3170 4040

2210 2750

2260 2830

2440 3140

320 200 220

3250 3800

3430 4030

4455 5500

2820 3370

2930 3530

3410 4250

2360 2880

2420 2970

2620 3290




0° 45° 90° 0° 45° 90° 0° 45° 90°

40 25 28

825 1305

840 1350

885 1535

645 1085

650 1110

665 1180

370 875

375 885

410 910 0°

50 32 36

1330 1645

1375 1715

1560 2030

1095 1395

1120 1430

1190 1560

875 1140

885 1160

910 1210

200063 40

451610 1980

1670 2000

1950 2000

1345 1700

1380 1750

1490 1950

1085 1410

1100 1435

1145 1510

80 50 56

1980 2000

2000 2000

2000 2000

1665 2000

1710 2000

1850 2000

1350 1730

1370 1760

1425 1860

100 63 70

2420 2880

2535 3000

3000 3000

2080 2530

2140 2630

2390 3000

1720 2140

1750 2190

1850 2360

125 80 90

3000 3000

3000 3000

3000 3000

2660 3000

2750 3000

3000 3000

2220 2810

2270 2890

2410 3000 45°

140 90 100

3000 3000

3000 3000

3000 3000

2970 3000

3000 3000

3000 3000

2490 3000

2550 3000

2740 3000

3000160 100

1103000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

2690 3000

2750 3000

2950 3000

180 110 125

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

2890 3000

2960 3000

3000 3000

200 125 140

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

3000 3000

220 140 160

5090 6000

5370 6000

6000 6000

4490 5510

4670 5800

5470 6000

3820 4850

3910 5020

4260 5750 90°

250 160 180

5520 6000

5860 6000

6000 6000

4940 6000

5170 6000

6000 6000

4270 5320

4410 5520

4920 6000 6000

280 180 200

6000 6000

6000 6000

6000 6000

5700 6000

5960 6000

6000 6000

4930 6000

5070 6000

5630 6000

320 200 220

6000 6000

6000 6000

6000 6000

5890 6000

6000 6000

6000 6000

4750 6000

5310 6000

6000 6000


Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

M

m

ps

v

v1 v2

p

ssd

v1

v2

p

ssd

m

m

α α


Formulas: m = Moved mass in kg v = Stroke velocity in m/s kv = See table on page 36

Extending:

Extending:

pS = System pressure in bar A1 = Piston area in cm2 (see page 3) A3 = Annulus area in cm2 (see page 3) α = Angle in degrees with reference to the horizontal plain

End position cushioning: The objective is to reduce the speed of a moving mass, whose centre of gravity lies on the cylinder axis, to a level, at which neither the cylinder nor the machine, into whih the cylinder is installed, can be damaged. For speeds over 20 mm/s we recommend the use of end position cushioning so that the energy can be absorbed without the use of any additi-onal equipment. Checks must always be carried out whether, also at lower speeds, with high masses end position cushio-ning is required.

Cushioning capacity: When braking masses via the end position cushioning, the design constricted cushioning capacity must not be exceeded. Cylinders with end position cushioning can only utilise their full cushioning capacity when the entire stroke length is used.

With the adjustable end position cushioning „E“ an additional throttle valve is aded to the „D“ version. The end position cushioning „E“ makes it possible to optimise the cycle times. The maximum cushioning capacity can only be achieved when the throttle valve is fully closed.

The calculation depends on the factors of weight, velocity, system pressure and installation position. Therefore, the variable Dm is to be calculated from weight and speed, the variable Dp from system pressure and installation position. These variables are then used to verify the permissible

End position cushioning

cushioning performance in the „cushioning capacity“ diagram. The interception point of the variables Dm and Dp must always be below the cushioning capacity curve of the selected cylinder. The values in the diagram refer to an average oil temperature of + 45 to +65 °C and with a closed throttle valve.

For special applications with very short stroke times, high speeds or masses, special cylinders with special end position cushioning can be offered on request.

When fixed or adjustable end stops are used, then special measures have to be taken!

mDm = ; 10K K = kv (0.5–v)

m • 9.81 • sinαDp = pS – A1 • 10

m • 9.81 • sinαDp = pS + A3 • 10

Damping length

AL Ø mm 40 50 63 80 100 125 140 160 180 200 220 250 280 320

Head side 21 20 23 25 25 25 33 33 37 37 76 81 86 90

Base side 21 20 23 25 25 25 33 33 37 37 76 81 86 90

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

1000000

100000

10000

1000

100

100 20 40 60 80 100 120 140 160 180 200

Ø320Ø280Ø250Ø220Ø200Ø180Ø160Ø140

Ø125Ø100Ø80Ø63Ø50Ø40

1



AL Ø mm 40 50 63 80 100 125 140 160 180 200 220 250 280 320

kv 1 2.85 2.97 2.56 2.82 3.51 3.02 2.53 2.65 2.91 2.76 2.85 2.95 3.11 3.13

kv 2 3.1 3.25 2.85 2.85 3.52 2.91 2.53 2.93 2.95 2.95 2.93 3.1 3.12 3.07

kv 3 2.95 3.1 2.73 3.1 3.51 2.95 2.51 2.91 2.95 2.91 2.93 2.93 3.15 3.25

AL = Piston Ø1) If, for standard applications, the calculated interception point

from Dm and Dp is within the indicated area, then we recommend that a cylinder is used without end position cushioning.

Cushioning capacity: Extending

Dm

→

Dp →

1)

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

10000000

1000000

100000

10000

1000

100

1040 80 120 160 200 24020 60 100 140 180 220

2Ø320/200Ø280/180Ø250/160Ø220/140

Ø200/125Ø180/110Ø160/100Ø140/90

Ø125/80Ø100/63Ø80/50Ø60/40Ø50/32Ø40/25

10000000

1000000

100000

10000

1000

100

1040 80 120 160 200 24020 60 100 140 180 220

3

Ø125/90Ø100/70Ø80/56Ø63/45Ø50/36Ø40/28

Ø320/220Ø280/200Ø250/180Ø220/160

Ø200/140Ø180/125Ø160/110Ø140/100


1) If, for standard applicaions, the calculated interception point from Dm and Dp is within the indicated area, then we recommend that a cylinder is used without end position cushioning.


Cushioning capacity: RetractingD

m →

Dp →

Dm

→

Dp →

1)

1)

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

1184 7 3 18 5 7 2

61818618

10 12 16

11 14 1717


Spare parts

CDH2

Piston rod Piston"M"

"A / B"

"T / S "

"M / T / S"

"A / B"

1 Head

2 Base

3 Barrel

4 Piston rod

5 Piston

6 Cushioning bush

7 Flange

10 Base MP3

11 Base MP5

12 Round flange MF3

14 Round flange MF4

16 Trunnion MT4

17 Foot MS2

18 Seal kit: Wiper Rod seal Piston seal O-ring Guide bush

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

1184 7 3 18 5 7

61818618

181

12 16 1717


1 Head

3 Barrel

4 Piston rod

5 Piston

6 Cushioning bush

7 Flange

12 Round flange MF3

16 Trunnion MT4

17 Foot MS2

18 Seal kit: Wiper Rod seal Piston seal O-ring Guide bush

CGH2

Piston rod Piston

"M"

"A / B"

"T / S"

"M / T / S "

"A / B"

Spare parts

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Series Piston Ø Piston rod Ø Screw Quantity Grade Tightening torque

CDH2 / CGH2 160100

M10 16 10.9 60 Nm110

CDH2 / CGH2 180110

M12 16 10.9 80 Nm125

CDH2 / CGH2 200125

M12 16 10.9 90 Nm140

CDH2 / CGH2 220140

M1216

10.9 90 Nm160 24

CDH2 / CGH2 250160

M12 24 10.9 90 Nm180

CDH2 / CGH2 280180

M12 24 10.9 90 Nm200

CDH2 / CGH2 320200 M12 24

10.990 Nm

220 M16 16 230 Nm

Screws: Seal cover (Pos. 3) 3

Tightening torque

Series Piston Ø Screw Quantity Grade Tightening torque

CDH2 / CGH2 40 M8 4 10.9 23 Nm

CDH2 / CGH2 50 M8 8 10.9 20 Nm

CDH2 / CGH2 63 M8 8 10.9 30 Nm

CDH2 / CGH2 80 M10 8 10.9 55 Nm

CDH2 / CGH2 100 M12 8 10.9 100 Nm

CDH2 / CGH2 125 M16 8 10.9 200 Nm

CDH2 / CGH2 140 M16 12 10.9 170 Nm

CDH2 / CGH2 160 M16 12 10.9 220 Nm

CDH2 / CGH2 180 M20 12 10.9 350 Nm

CDH2 / CGH2 200 M20 12 10.9 410 Nm

CDH2 / CGH2 220 M20 16 10.9 460 Nm

CDH2 / CGH2 250 M24 16 10.9 700 Nm

CDH2 / CGH2 280 M30 12 10.9 1700 Nm

CDH2 / CGH2 320 M30 16 10.9 1500 Nm

Screws: Head and base (Pos. 1 and 2)

1 2

Only for seal versions "A" and "B"

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Seal kits1)

CDH2 – Standard

AL = Piston Ø in mm

MM = Piston rod Ø in mm1) = Seal kits for position measuring system and

proximity switches have separate Material Nos.

AL MM Material No. for seal version

Ø Ø M T A S B

4025 R901010141 R901010143 R901010145 R901010146 R901010147

28 R900851087 R900858841 R900859445 R900861001 R900859770

5032 R900860274 R900860275 R900860929 R900861003 R900860939

36 R900849392 R900860277 R900851515 R900861004 R900860940

6340 R900859509 R900860279 R900851637 R900861006 R900860941

45 R900847956 R900847855 R900851638 R900861007 R900859678

8050 R900857129 R900860281 R900856092 R900861009 R900860943

56 R900850905 R900856180 R900854718 R900861010 R900851205

10063 R900860283 R900860284 R900856093 R900861012 R900860945

70 R900853382 R900860285 R900856094 R900861013 R900860946

12580 R900860287 R900860288 R900860931 R900861015 R900860950

90 R900857949 R900856102 R900856095 R900861016 R900855464

14090 R900858281 R900860289 R900860932 R900861017 R900860951

100 R900853965 R900860290 R900856096 R900849080 R900860952

160100 R900855683 R900860291 R900860468 R900861018 R900860953

110 R900851146 R900857536 R900860933 R900861019 R900860954

180110 R900856497 R900852561 R900860934 R900861020 R900860955

125 R900848603 R900860292 R900860935 R900861021 R900860956

200125 R900860294 R900860295 R900860936 R900861022 R900860957

140 R900856431 R900860293 R900860937 R900861023 R900860958

220140 R900888100 R900888108 R900888116 R900888132 R900888140

160 R900888101 R900888109 R900888117 R900888133 R900888141

250160 R900888102 R900888110 R900888118 R900888134 R900888142

180 R900888103 R900888111 R900888119 R900888135 R900888143

280180 R900888104 R900888112 R900888120 R900888136 R900888144

200 R900888105 R900888113 R900888121 R900888137 R900888145

320200 R900888106 R900888114 R900888122 R900888138 R900888146

220 R900888107 R900888115 R900888123 R900888139 R900888147

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


CGH2 – Standard

Seal kits1)

AL = Piston Ø

MM = Piston rod Ø1) = Seal kits for proximity switches have separate Material Nos.

AL MM Material No. for seal versions

Ø Ø M T A S B

4025 R901010159 R901010161 R901010162 R901010169 R901010170

28 R900867252 R900868889 R900866747 R900868943 R900867133

5032 R900867254 R900868891 R900866749 R900868945 R900857135

36 R900864930 R900868892 R900866750 R900868946 R900867136

6340 R900867261 R900868894 R900866752 R900868948 R900867138

45 R900867262 R900868895 R900866753 R900868949 R900867139

8050 R900867264 R900868897 R900866755 R900868951 R900867141

56 R900867265 R900868898 R900866756 R900868952 R900867142

10063 R900867267 R900868900 R900866758 R900868954 R900867144

70 R900867268 R900868901 R900866759 R900868955 R900867146

12580 R900860730 R900868903 R900866761 R900868956 R900867148

90 R900867270 R900868904 R900866762 R900868957 R900867149

14090 R900867271 R900868905 R900866763 R900868958 R900867150

100 R900867272 R900868906 R900866764 R900868959 R900867151

160100 R900867273 R900868907 R900866765 R900868960 R900867152

110 R900867274 R900868908 R900866766 R900868961 R900867153

180110 R900867275 R900868909 R900866767 R900868962 R900867154

125 R900867276 R900868910 R900866768 R900868963 R900867155

200125 R900867277 R900868911 R900866769 R900868964 R900867156

140 R900867278 R900868912 R900866770 R900868965 R900867157

220140 R900888020 R900888028 R900888036 R900888052 R900888060

160 R900888021 R900888029 R900888037 R900888053 R900888061

250160 R900888022 R900888030 R900888038 R900888054 R900888062

180 R900888023 R900888031 R900888039 R900888055 R900888063

280180 R900888024 R900888032 R900888040 R900888056 R900888064

200 R900888025 R900888033 R900888041 R900888057 R900888065

320200 R900888026 R900888034 R900888042 R900888058 R900888066

220 R900888027 R900888035 R900888043 R900888059 R900888067

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


CDH2 – Standard + Option F

CGH2 – Standard + Option F

Seal kits1)

AL = Piston ØMM = Piston rod Ø

1) = Seal kits for proximity switches have separate Material Nos.


Ø Ø M+F T+F S+F

4025 R901010151 R901010154 R901010156

28 R900868999 R900869026 R900869093

5032 R900869001 R900869028 R900869095

36 R900869002 R900869029 R900869096

6340 R900869004 R900869031 R900869098

45 R900869005 R900869032 R900869099

8050 R900869007 R900869034 R900869101

56 R900869008 R900869035 R900869102

10063 R900869012 R900869037 R900869104

70 R900869013 R900869038 R900869105

12580 R900869015 R900869040 R900869107

90 R900869016 R900869041 R900869108

14090 R900869017 R900869042 R900869109

100 R900869018 R900869043 R900869110

160100 R900869019 R900869044 R900869111

110 R900869020 R900869045 R900869112

180110 R900869021 R900869046 R900869113

125 R900869022 R900869047 R900869114

200125 R900869023 R900869048 R900869115

140 R900869024 R900869049 R900869116


Ø Ø M+F T+F S+F

4025 R901010148 R901010149 R901010150

28 R900861025 R900861050 R900861100

5032 R900861027 R900861052 R900861102

36 R900861028 R900861053 R900861103

6340 R900861030 R900861055 R900861105

45 R900861031 R900861056 R900861106

8050 R900861033 R900861058 R900861108

56 R900861034 R900861059 R900861109

10063 R900861036 R900861061 R900861114

70 R900861037 R900861062 R900861115

12580 R900861039 R900861064 R900861120

90 R900861040 R900861065 R900861122

14090 R900861041 R900861066 R900861124

100 R900861042 R900861067 R900861126

160100 R900861043 R900861068 R900861128

110 R900861044 R900861069 R900861130

180110 R900861045 R900861070 R900861133

125 R900861046 R900861071 R900861135

200125 R900861047 R900861072 R900861142

140 R900861048 R900861073 R900861143

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om


Bosch Rexroth AG HydraulicsZum Eisengießer 197816 Lohr am Main, Germany Telefon +49 (0) 93 52 / 18-0 Telefax +49 (0) 93 52 / 18-23 [email protected] www.boschrexroth.de

© This document, as well as the data, specifications and other informations set forth in it, are the exclusive property of Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.The data specified above only serves to describe the product. No statements concerning a certain condition or suitability for a certain

application can be derived from our information. The details stated do not release you from the responsibility for carrying out your own assessment and verification. It must be remembered that our products are subject to a natural process of wear and ageing.

Bosch Rexroth Teknik AB Varuvägen 7, ÄlvsjöS-125 81 StockholmTelefon +46 (08) 72 79 20 0 Telefax +46 (08) 86 87 [email protected] www.boschrexroth.se

Bosch Rexroth SA BP 37 - Z.I. Les FourmisF-74131 Bonneville Cedex Telefon +33 (0) 4 50 25 35 45 Telefax +33 (0) 4 50 25 35 19www.boschrexroth.fr

Seal kits

Only for the position measuring system

Only for the proximity switches

AL Material No. for seal versions

Ø M / M+F T / T+F A S / S+F B

40 R900885935 – R900885937 –

50 R900894958 – R900894979 –

63 R900894959 – R900894980 –

80 R900894960 – R900894981 –

100 R900894961 – R900894982 –

125 R900894962 – R900894983 –

140 R900894963 – R900894985 –

160 R900894964 – R900894986 –

180 R900894973 – R900894987 –

200 R900894974 – R900894988 –

220 R900894975 – R900894989 –

250 R900894976 – R900894991 –

280 R900894977 – R900894993 –

320 R900894978 – R900894994 –

AL Material No. for seal versions

Ø M / M+F T / T+F A S / S+F B

40 bis 200

R900885938 R900885939

220 bis 320

R900894997 R900894998

AL = Piston Ø

Court

esy

of CM

A/F

lodyn

e/H

ydra

dyn

e ▪

Motion C

ontr

ol ▪

Hyd

raulic

▪ P

neu

mat

ic ▪

Ele

ctrica

l ▪

Mec

han

ical

▪ (

800)

426-5

480 ▪

ww

w.c

maf

h.c

om

Documents

RE 17334 2007-10 PDFs/BRH CYL/Rexroth...Hydraulic cylinder 1/44 Mill type Series CDH2 / CGH2 Component series 1X Nominal pressure 250 bar (25 MPa) RE 17334/10.07 Replaces: 09.05 Overview