samsung_cs3339z6x_cs3366z6x_cs5039z6x_chassis_s15a.pdf

COLOR TELEVISION RECEIVERChassis : S15AModel : CS3339Z6X/TAW CS3366Z6X/AWE

CS5039Z6X/AWE

COLOR TELEVISION RECEIVER CONTENTS

Precautions

Reference Information

Specifications

Alignment and Adjustments

Troubleshooting

Exploded Views and Parts List

Electrical Parts List

Block Diagrams

Wiring Diagram

Schematic Diagrams

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

ELECTRONICS

Samsung Electronics Co., Ltd. MAR. 2001Printed in Korea3S15A-SIA3339-01

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protectivedevices are replaced. Restore any missingprotective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protectivedevices, including: nonmetallic control knobsand compartment covers.

3. Make sure that there are no cabinet openingsthrough which peopleparticularly childrenmight insert fingers and contactdangerous voltages. Such openings includethe spacing between the picture tube and thecabinet mask, excessively wide cabinetventilation slots, and improperly fitted back

covers.

If the measured resistance is less than 1.0megohm or greater than 5.2 megohms, anabnormality exists that must be correctedbefore the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):Warning: Do not use an isolation transformer during this test. Use a leakage-current tester or a metering system that complies with American National StandardsInstitute (ANIS C101.1, Leakage Current forAppliances), and Underwriters Laboratories(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plugthe AC line cord directly into the power outlet. With the units AC switch first in theON position and then OFF, measure the current between a known earth ground (metalwater pipe, conduit, etc.) and all exposedmetal parts, including: antennas, handlebrackets, metal cabinets, screwheads and control shafts. The current measured shouldnot exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat thetest.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check: With the units AC plug disconnected from theAC source, connect an electrical jumper acrossthe two AC prongs. Connect one lead of theohmmeter to an AC prong. Connect the otherlead to the coaxial connector.

7. X-ray Limits:The picture tube is especially designed to pro-hibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube onlywith one that is the same type as the original.Carefully reinstall the picture tube shields andmounting hardware; these also provide X-rayprotection.

8. High Voltage Limits:High voltage must be measured each time ser-vicing is done on the B+, horizontal deflectionor high voltage circuits. Correct operation ofthe X-ray protection circuits must be reconfirmed whenever they are serviced.(X-ray protection circuits also may be called

horizontal disable or hold-down.)

Heed the high voltage limits. These includethe Xray Protection Specifications Label, andthe Product Safety and X-ray Warning Note onthe service data schematic.

Precautions

Samsung Electronics 1-1

LEAKAGECURRENTTESTER

DEVICEUNDERTEST

TEST ALLEXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITHPLUG REVERSED

(USING AC ADAPTERPLUG AS REQUIRED)

EARTHGROUND

(READING SHOULDNOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potentialhazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specifiedlimits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, checkeach of the special components.

10. Design Alteration Warning:Never alter or add to the mechanical or electrical design of this unit. Example: Do notadd auxiliary audio or video connectors. Suchalterations might create a safety hazard. Also,any design changes or additions will void themanufacturers warranty.

11. Hot Chassis Warning:Some TV receiver chassis are electrically connected directly to one conductor of the ACpower cord. If an isolation transformer is notused, these units may be safely serviced onlyif the AC power plug is inserted so that thechassis is connected to the ground side of theAC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the ACpower plug, reverse its polarity and reinsert.Re-measure the voltage between the chassisand ground.

12. Some TV chassis are designed to operate with85 volts AC between chassis and ground,regardless of the AC plug polarity. These unitscan be safely serviced only if an isolationtransformer inserted between the receiver andthe power source.

13. Some TV chassis have a secondary groundsystem in addition to the main chassis ground.This secondary ground system is not isolated from the AC power line. The twoground systems are electrically separated byinsulating material that must not be defeatedor altered.

14. Components, parts and wiring that appear tohave overheated or that are otherwise damaged should be replaced with parts thatmeet the original specifications. Always determine the cause of damage or overheat-ing, and correct any potential hazards.

15. Observe the original lead dress, especiallynear the following areas: Antenna wiring,sharp edges, and especially the AC and highvoltage power supplies. Always inspect forpinched, out-of-place, or frayed wiring. Donot change the spacing between componentsand the printed circuit board. Check the ACpower cord for damage. Make sure that leadsand components do not touch thermally hotparts.

16. Picture Tube Implosion Warning:The picture tube in this receiver employsintegral implosion protection. To ensurecontinued implosion protection, make surethat the replacement picture tube is the sameas the original.

17. Do not remove, install or handle the picturetube without first putting on shatterproofgoggles equipped with side shields. Neverhandle the picture tube by its neck. Some in-line picture tubes are equipped with a permanently attached deflection yoke; do nottry to remove such permanently attachedyokes from the picture tube.

18. Product Safety Notice: Some electrical and mechanical parts havespecial safety-related characteristics whichmight not be obvious from visual inspection.These safety features and the protection theygive might be lost if the replacement compo-nent differs from the originaleven if thereplacement is rated for higher voltage,wattage, etc.

Components that are critical for safety areindicated in the circuit diagram by shading, ( ) or ( ).

Use replacement components that have thesame ratings, especially for flame resistanceand dielectric strength specifications. A replacement part that does not have thesame safety characteristics as the originalmight create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

!

1-2 Servicing Precautions

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the units AC power cord fromthe AC power source before attempting to: (a)Remove or reinstall any component or assembly, (b) Disconnect an electrical plug orconnector, (c) Connect a test component inparallel with an electrolytic capacitor.

3. Some components are raised above the printedcircuit board for safety. An insulation tube ortape is sometimes used. The internal wiring issometimes clamped to prevent contact withthermally hot components. Reinstall all suchelements to their original position.

4. After servicing, always check that the screws,components and wiring have been correctlyreinstalled. Make sure that the portion aroundthe serviced part has not been damaged.

5. Check the insulation between the blades of theAC plug and accessible conductive parts(examples: metal panels, input terminals andearphone jacks).

6. Insulation Checking Procedure: Disconnect thepower cord from the AC source and turn thepower switch ON. Connect an insulationresistance meter (500V) to the blades of the ACplug.

The insulation resistance between each bladeof the AC plug and accessible conductive parts(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.Do not apply AC power to the unit (or any ofits assemblies) unless all solid-state heat sinksare correctly installed.

8. Always connect a test instruments groundlead to the instrument chassis ground beforeconnecting the positive lead; always removethe instruments ground lead last.

Precautions


Warning1: First read the Safety Precautions section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Some semiconductor (solid state) devicesare easily damaged by static electricity. Suchcomponents are called ElectrostaticallySensitive Devices (ESDs); examples includeintegrated circuits and some field-effect transistors. The following techniques willreduce the occurrence of component damagecaused by static electricity.

2. Immediately before handling any semiconductor components or assemblies, drain theelectrostatic charge from your body by touching a known earth ground. Alternatively,wear a discharging wrist-strap device. (Besure to remove it prior to applying powerthis is an electric shock precaution.)

3. After removing an ESD-equipped assembly,place it on a conductive surface such as aluminum foil to prevent accumulation ofelectrostatic charge.

4. Do not use freon-propelled chemicals. Thesecan generate electrical charges that damageESDs.

5. Use only a grounded-tip soldering iron whensoldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.Many solder removal devices are not rated asanti-static; these can accumulate sufficientelectrical charge to damage ESDs.

7. Do not remove a replacement ESD from itsprotective package until you are ready toinstall it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protectivematerial from the leads of a replacement ESD,touch the protective material to the chassis orcircuit assembly into which the device will beinstalled.

9. Minimize body motions when handlingunpackaged replacement ESDs. Motions suchas brushing clothes together, or lifting a footfrom a carpeted floor can generate enough static electricity to damage an ESD.

Precautions


1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

Specifications and IC Data


2. Specifications and IC Data

2-1 Specifications

Television System:

Channels:

Intermediate Frequencies (MHz) :

Picture Tube:

Power Requirements:

Antenna Input Impedance:

Speaker Impedance

NTSC - M

2 - 13

14-69

NTSC - M

38.90

34.40

35.32

PAL/SECAM-B/G,I

2 - 12

21 - 69

PAL/SECAM- B/G

38.90

33.40

34.47

SystemBand

VHF

UHF

SYSTEMIF Carrier Frequency

Picture IF Carrier

Sound IF Carrier

Color Sub Carrier

PAL,SECAM- D/K

1 - 13

21 - 69

PAL/SECAM-D/K,SECAM-K1

38.90

32.40

34.47

SECAM-K1,PAL-D

2 - 9

13 - 57

PAL - I

38.90

32.90

34.47

MODEL

CI

CII

CX

CK

CW

CS

14 Inch

20 Inch

21 Inch

AC 100~260V, 50/60Hz

VHF, UHF : Telescopic dipole antenna (75 ohm unbalanced type )

8 ohm, 5W+5W (Dual Type)16 ohm, 3W (Monitor Type & Dual Type)

SYSTEM

PAL-I (UHF)

PAL-I (VHF/UHF)

PAL-B/G, SECAM-B/G

PAL-B/G, D/K, SECAM-B/G, D/K

PAL-B/G, D/K, SECAM-B/G, D/K, NT 4.43

PAL-B/G, D/K, SECAM-B/G, D/K, NT4.43, NT3.58

A34KQV42X

A48KRD82X(H)

A51KQJ63X

Quick start, in-line-gun,

Black stripe, 90 degree deflection

2-2 IC Line Up



Loc. No Specification Description Remark

HC101 PAP103 IF PRE-AMP

IC201 TDA8842 PAL/SECAM-B/G, D/K, NTSC Philips TDA8841 PAL-B/G, D/K, NTSC

IC301 TDA8356 VERTICAL OUTPUT

IC501 TDA6107Q RGB DRIVE AMP

IC601 TDA7056B SOUND-AMP (3W x 1CH or 3W x 2CH)

IC602 TDA7057AQ SOUND-AMP (5W x 2CH)

IC801 KA3S0680RF POWER IC (STR)

IC802 KA7630 CUSTOM REGULATOR (5V, 8V)

Table 2-1 IC Line-Up

SZM173EA W/O TTX, English/French/Arabian

SZM173EC W/O TTX, English/Chinese

SZM173ET W/O TTX, English/Thai

SZM173EW W/O TTX, English/German/French/Dutch/Italian/Spanish, Swedish/Yugo/Greek/Croatian

SZM173EE W/O TTX,English/Romanian/Hungarian/Polish/Czech/Bulgarian SZM173ER W/O TTX, English/Russian

SPM175EE TTX, West : English/German/French/Dutch/Italian/Spanish/Swedish East : English/Czech/Croatian/Romanian/Hungarian/Polish

SZM173EV W/O TTX, English/Vietnamese/Indonesian/Malay

IC902 24C04/KS24C040 EEPROM

PC801 TCET1108 / LTV817B PHOTO COUPLER

SPM175ER TTX, English/Russian/Bulgarian

SPM175EP TTX, English/Iranian

SPM175EA TTX, English/French/Arabian

SPM175EG TTX, English/Greek/Yugo

Dual Type

Zilog(Non TTX)

Philips(TTX)

IC901

SZM173AR W/O TTX, English/Arabian

SPM175E TTX, English/French/Swiss

2-3 Semiconductor Base Diagrams



ELECTROLYTIC-CONDENSER

ICDIODE

TDA884X(Pin 56)Z8933112PSC(Pin 42)X24CO4P(Pin 8)SAA5291(Pin 52)TDA9859(Pin 32)KS24C040(Pin 8)

IC TRANSISTOR

TDA8133TDA8356TDA6101QKA7630

TRANSISTORTRANSISTOR

2SD16512SD1650KSD5072KSD5071KSD1711KSC5386

BC

E E B C

KSC815-YKSA539-YBC548KTC9014

IC

UPC574Jor

KA33V

SAW-FILTER

E C B

KSR1012KSR1010KSR2010KTD863-Y

111

K2971MK7252M

Fig. 2-1 Semiconductor Base Diagrams


MEMO

Disassembly and reassembly


3. Disassembly and Reassembly

3-1 Back Cover Removal

1. After removing the screws, press the tension rib and pull the cabinet backwards.

2. To reassemble, press the tension rib (see diagram).

3-2 Main Board Removal



1. Separate the socket board from the CRT neck.

2. Remove the Anode Cap from the CRT.

3. Remove the main board by pulling it with both hands.

Warning: The FBT is charged with high voltage. Before removing the Anode Cap, discharge the voltage through one of the heat sinks on the main board.

3-3 Speaker Removal



1. Remove the speaker bypressing the tension rib.

1. Remove the screws.

2. Remove the speaker bypressing the tension rib.



3-4 CRT Removal

1. Spread a soft mat on the floor. Place the TV set facedown.

2. Remove the 4 nuts mounting the CRT to the front cabi-net. Lift the CRT.

3. Caution: Because of the high vacuum and large surfacearea of the picture tube, be careful while handling it: (1)Always lift the picture tube by grasping it firmly aroundthe faceplate, (2) Never lift the tube by its neck. (3) Donot scratch the picture tube or apply excessive pressure.Fractures of the glass may cause an implosion.



4. Alignment and Adjustments

4-1 Preadjustment

4-1-1 Factory Mode

1. Do not attempt these adjustments in the VideoMode.

2. The Factory Mode adjustments are necessarywhen either the EEPROM (IC902) or the CRTis replaced.

3. Do not tamper with the Adjustment screenof the Factory Mode menu. This screen isintended only for factory use.

4-1-2 When EEPROM (IC902) Is Replaced

1. When IC902 is replaced all adjustment datarevert to initial values. It is necessary tore-program this data.

2. After IC902 is replaced, warm up the TV for10 seconds.

4-1-3 When CRT Is Replaced

1. Make the following adjustments AFTER set-ting up after setting up purity and conver-gence :

White Balance Sub-Brightness Vertical Center Vertical SizeHorizontal Size Fail Safe (This adjustment must be the laststep).

2. If the EEPROM or CRT is replaced, set PVA to45 (factory mode) and set SC as follows.

14, 16 inch : 020 inch : 1021 inch : 12

4-2 Factory/Service Mode

4-2-1 Procedure for the Adjustment Mode

1. This mode uses the standard remote control.The Service Mode is activated by entering thefollowing remote-control sequence :

(1) SLEEPFACTORY.

(2) STAND-BY DISPLAY P.STD MUTEPOWER ON.

2. The SERVICE (FACTORY) message will bedisplayed. The Service Mode has four compo-nents: Adjustment, Test Pattern, Option Bytesand Reset.

3. Access the Adjustment Mode by pressing theVOLUME keys ( Up or Down). The adjust-ment parameters are listed in the accompany-ing table, and selected by pressing the CHAN-NEL keys ( ,).

4. Selection sequences for the all system:

DOWN or UP key:AGC>VCO>SBT>SCT>SCR>SC>RG>GG>BG>CDL>BLU>PSL>PVS>PVA>PHS>NSR>STT

5. The VOLUME keys increase or decrease theadjustment values (stored in the non-volatile memory) when Adjustment Modeis cancelled.

6. Cancel the Adjustment Mode by re-pressingthe FACTORY or Power OFF keys.

4-2-2 Main Adjustment Parameter

NOTE : PVS,PVA, PHS, parameters must be aligned using the 50Hz vertical-field rates.



INITIAL DATA

10

8

10

10

47

32

34

32

32

42

40

7

0

80

12

4

0

REMARK

TDA8842TDA8841

RANGE

0 ~ 63 STEP

0 ~ 23 STEP

0 ~ 23 STEP

0 ~ 23 STEP

0 ~ 63 STEP

0 ~ 63 STEP

0 ~ 63 STEP

0 ~ 63 STEP

0 ~ 63 STEP

0 ~ 63 STEP

0 ~ 63 STEP

0 ~ 23 STEP

1 ~ 13 STEP

0 ~ 128 STEP0 ~ 1 STEP 1 (For East Europe)

0 ~ 63 STEP

0 ~ 63 STEP 16 (Only TTX Model)

0 ~ 7 STEP

0 ~ 3 STEP

OSD ABBREVIATION

AGC

SBT

SCT

SCR

RG

GG

BG

PSL

PVS

PVA

PHS

NSR

STT

VCO

SC

TSS

CDL

BLU

FUNCTION

AUTO GAIN CONTROL

SUB BRIGHT

SUB CONTRAST

SUB COLOR

RED DRIVE GAIN

GREEN DRIVE GAIN

BLUE DRIVE GAIN

PAL VERTICAL SLOPE

PAL VERTICAL SHIFT

PAL VERTICAL AMPLITUDE

PAL HORIZONTAL SHIFT

NTSC SUB COLOR

SUB TINT

VOLTAGE CONTROL OSCILLATOR

S-CORRECTION

TTX SUB-CONTRAST

CATHODE DRIVE LEVEL

BLUE STRETCH MODE

Table 4-1 Main Adjustment Parameter (Zilog, Phlips -com)



4-2-3 Test Pattern (Aging Mode)

1. This mode can be used during servicing, or for confirming that the convergence andpurity adjustments are correct.

2. Access the Test Pattern parameters by pressing a CHANNEL keys ( ,) while theService Mode is on. The cursor will move to the test pattern. Press the VOLUMEkeys. On-screen display:

WHITE

AGING

3. AGING Mode (Reference Only)

This pattern is used for pre-heating the CRT during manufacturingit is accessed in the factory by twice pressing the SLEEP FACTORYFACTORY key, then white pattern will be displayed.

Even if the TV power is cut off, the Aging Mode is not cancelled, The aging mode iscancelled by repressing the FACTORY key or pressing the local CH UP/DOWNkeys.

4-2-4 Option Bytes

In the Service Mode, various can be selected via the Option Bytes (8 bits each). Example:

NON -TTX MICOM ONLY

TTX MICOM

SYSTEM OSD DISPLAY BIT 6

L (BIT :0)

BIT 5

L (BIT : 0)

BIT 4L (BIT : 0)L (BIT : 0)

BIT 3H (BIT : 8)L (BIT : 0)




BYTE 0 : 8 -BYTE 1 : 0 -

TDA8842, CK SYSTEM, RCA JACK SYSTEM OSD DISPLAY

L (BIT : 1) H (BIT : 0) L (BIT : 0) H (BIT : 0) L (BIT : 1)BYTE 0 : 11



4-2-4 (A) NON-TTX MICOM (SZM-173EC) OPTION BYTE (FOR CHINA/SINGAPORE/GERMAN ARMY)

BYTE BIT LOW (0) HIGH (1) Application MICOM

B

Y

T

E

0

D7 NOT USED MUST LOW

D6TV : NORMAL ZOOM

A/V :NORMAL ZOOM

TV: NORMAL ZOOM 16:9

A/V : NORMAL ZOOM

D5 NOT USED MUST = LOW

D4CH Up/down functional in

the A/V Mode (SCART Jack)

CH Up/down not functional in

the A/V Mode (RCA Jack)

D3 Sound-I System Used Sound-I System Not Used

D 2

D 1

D0 TDA8374A TDA8842 IC201 (ONE-CHIP) OPTION

B

Y

T

E

1

D7 TV OUT MONITOR OUT

D6 English ONLY English/Chinese

D5 AFT ON (always) AFT OFF (after fine tuning) BASIC = LOW

D4

Existing Sharpness level

(when using the TDA6108

RGB AMP)

Sharpness level up

(when using the TDA6107Q

RGB AMP)

D3 No Auto Power On Auto Power On

D2NT SC : 25K H z (NTSC TABLE)

P A L : 50K H z (PA L TABLE)NTSC : 25KHz (NTSC TABLE)

PAL : 27KHz (NTSC TABLE)

D1

NOT USED MUST LOWD0

D2 D1 COLOR SYSTEM SOUND SYSTEM Remark0 0 CB : NO OSD

German Army : CS

0 1CW : RF : AUTO PAL SECAM NT4.43

A/V : AUTO PAL SECAM NT4.43 NT3.58B/G D/K I

1 0CD : RF : AUTO PAL NT4.43

A/V : AUTO PAL NT4.43 NT3.58D/K I

1 1CS : RF: AUTO PAL SECAM NT4.43 NT3.58

A/V: AUTO PAL SECAM NT4.43 NT3.58B/G D/K (I)NT- M

D3 BITOPTION

Function Required : 1. PICTURE OFF (after 15 minutes) during no signal

2. AUDIO MUTE during no signal

3. BLUE SCREEN ON/OFF

4. TIMER CLOCK ON/OFF

5. No CHILD LOCK

Destination BYTE 0 BYTE 1

MP (Massproduction)

OPTION BYTE

China 15 58

Singapore 57 58

German Army

59

57 18

MUST = LOW : China (only) 16 : 9 (Delete)

MUST = HIGH

China MP : CD"?"

"?"

"?"

MUST = HIGH

BASIC = HIGH

BASIC = HIGH

Hotel ( CB ) 59 1A

Others HOTEL

Austaralia 18



4-2-4 (B) NON-TTX MICOM (SZM-173EW/EE) OPTION BYTE (FOR EUROPE)

BYTE BIT LOW(0) HIGH(1) Remark

BYTE

0

D7 3 BAND UHF ONLY HIGH (UK only)

D6TV : NORMAL ZOOM

A/ : NORMAL ZOOM

TV : NORMAL ZOOM 16:9

A/V : NORMAL ZOOMMUST = HIGH

D5 MUST LOW - R 913 : 680 added

- J901 :

D4CH Up/down functional in the

A/V Mode (SCART Jack)


the A/V Mode (RCA Jack)MUST = LOW

D3 NOT USED MUST = LOW

D2

D1


BYTE

1

D7English/German/Dutch/Italian/Spnish/

Swedish/Croatian/Yugo/Greek/French

W ester n E urope

(SZM-173EW/EW1)

D6E nglish/R om anian/H ungarian/Polish/

C zech /B ulgarianEastern Europe (SZM-173EE)

D5 AFT ON (always) AFT OFF (after fine tuning) MUST = LOW

D4 Existing sharpness level : TDA6108 Sharpness level up : TDA6107Q MUST = HIGH


D2NTSC : 25 KHz (NTSC TABLE)

PAL : 50 KHz (PAL TABLE)

NTSC : 25KHz(NTSC TABLE)

PAL : 27KHz(NTSC TABLE)

D1 PAL / SECAM SECAM - L - France/Swiss (only) : HIGH

D0 MUST : LOW

D2 D1 SOUND SYSTEM COLOR SYSTEM Destination

0 0 "?" B/G D/K : CK MODEL

AUTO : NO OSD

Eastern Europe/France/Swiss

0 1 I ONLY ( NO OSD ) : CI,CII MDL United Kingdom

1 0 B/G ONLY (NO OSD ) : CB,CX MDL Western Europe

1 1 NOT USED


MP OPTION

BYTE

United Kingdom C3 98

France/Swiss 45 9A

Western Europe (except UK) 45 98

Eastern Europe 41 58

P-STD Classification ( CON./BRI./SHAR./COL )

STANDARD

MODE

DYNAMIC

MODEMOVIE MODE MILD MODE CUSTOM MODE

90/50/50/50 100/50/75/50 90/50/75/50 60/50/50/50 90/50/50/50

Function Required: 1. PICTURE OFF (after 15 minutes) during no signal. 2. AUDIO MUTE during no3. No BLUE SCREEN during no RF signal (Blue Screen during AV).4. No TIMER. 5. No CHILD LOCK. 6. See "Detailed functions of CF".

signal.

MUST = HIGH

delete

POLAND OPTION

Ireland (CII) 43 98



4-2-4 C) NON-TTX MICOM (SZM-173ER) OPTION BYTE (FOR RUSSIA)


Russia,CIS 49 58

Australia 5D 18


BYTE

0

D7

D6TV : NORMAL ZOOM

A/V : NORMAL ZOOM


A/V : NORMAL ZOOM

D 5




the A/V Model (RCA Jack)

D3 PAL-I Used PAL-I Not Used

D2

D1


BYTE

1

D7

D6 English English/Russian

D5 AFT ON (always) AFT OFF (after fine tuning)

D4Existing sharpness level

(when using the TDA6108 RGB AMP)

Sharpness level up

(when using the TDA6107Q AMP)


D2NTSC: 25 KHz (NTSC TABLE)


NTSC : 25 KHz (NTSC TABLE)PAL : 27 KHz (NTSC TABLE)

D1

D0

Function Required : 1. PICTURE OFF (after 15 minutes) during no signal

2. AUDIO MUTE during no signalSCREEN available

4. TIMER available5.

P-STD Classification ( CON/BRI/SHAR/COL )

STANDARD

MODE

DYNAMIC

MODEMOVIE MODE MILD MODE CUSTOM MODE

90/50/50/50 100/50/75/50 90/50/75/50 60/50/50/50 90/50/50/50

D2 D1 SOUND SYSTEM COLOR SYSTEM

0 0 "?" B/G D/K : CK MODEL AUTO : NO OSD

0 1 I ONLY (NO OSD ) : CI,CII MDL

1 0 B/G ONLY (NO OSD ) : CB,CX MDL

1 1 NOT USED

3. BLUE

MUST = LOW

MUST = HIGH

MUST = LOW

MUST = HIGH

MUST = LOW

MUST = HIGH

BASIC = HIGH

NOT USED (MUST = LOW)

No CHILD LOCK

India (CB MONO MODEL) 38

5D

BASIC = LOW ( India HIGH )

Remark

Russia 59 58

Scart - 21 pin

Rca - 4 pin



4-2-4 (D) NON-TTX MICOM (SZM-173AR/EA) OPTION BYTE (FOR MIDDLE EAST/AFRICA)

BYTE BIT LOW (0) HIGH (1) Remark

BYTE

0

D7

D6TV : NORMAL ZOOM

A/V : NORMAL ZOOM


A/V : NORMAL ZOOM

D5 NOT USED CHILD LOCK ON



CH Up/down not functional in the

A/V Model (RCA Jack)

Middle East : HIGH

Africa : LOW


D2

D1


BYTE1

D7

D6

D5 AFT ON (always) AFT OFF after fine tuning

D4Existing sharpness level (when

using the TDA6108 RGB AMP)

Sharpness level up (when using the

TDA6107Q RGB AMP)


D2NT SC : 25 KH z ( NTSC T A B L E )

P A L : 50 KH z ( PAL T A B L E )

NTSC : 25 KHz (NTSC TABLE)

PAL : 27 KHz (NTSC TABLE)

D1

D0

D2 D1 COLOR SYSTEM SOUND SYSTEM

0 0 CK : AUTO (NO OSD ) "?" B/G D/K

0 1CW : -. RF : AUTO PAL SECAM NT4.43

-. A/V : AUTO PAL SECAM NT4.43 NT3.58"?" B/G D/K I

1 0CB : - RF : PAL ONLY

- A/V : AUTO PAL NT4.43 NT3.58B/G ONLY (NO OSD)

1 1CS : -. RF : AUTO PAL SECAM NT4.43 NT3.58

-. A/V : AUTO PAL SECAM NT4.43 NT3.58

"?" B/G D/K I

NT- M


MP OPTION

BYTE

Middle East (EA or AR) 7F 58

Africa (EA) 67 D8

D7 D6 LANGUAGE Remark

0 0 - NOT USED

0 1 ENG / ARAB Middle East

1 0 - NOT USED

1 1 ENG / ARAB / FRENCH EA VERSION (Africa ONLY)

Function Required : 1. PICTURE OFF (after 15 minutes) during no signal2. AUDIO MUTE during no signal.

SCREEN ON/OFF4. TIMER (CLOCK ON/OFF)5. (always)

3. BLUE

MUST = LOW

MUST = HIGH

MUST = HIGH

MUST = HIGH

MUST = LOW

MUST = HIGH

CHILD LOCK ON

GAME (Middle East) 7F 5A

Others GAME

MUST = LOW



4-2-4 (E) NON-TTX MICOM (SZM-173EV/ET) OPTION BYTE (FOR ASIA)

BYTE BIT LOW (0) HIGH (1) Remark

BYTE

0

D7 LINE STEREO OFF LINE STEREO ON SZM-173EV (only)

D6TV : NORMAL ZOOM

A/V : NORMAL ZOOM


A/V : NORMAL ZOOM

D5 MUST = LOW






D 2

D 1


BYTE

1

D7 TV OUT MONITOR OUT

D6 E nglish O NL YE nglish/V ietnamese/Indonesian/Malay SZM-173EV

English/Thai SZM-173ET

D5 AFT ON (always) AFT OFF (after fine tuning)

D4


D2

D1

D0 MUST = LOW

D2 D1 COLOR SYSTEM SOUND SYSTEM Destination

0 0 CK :AUTO (NO OSD) "?" B/G D/K

0 1CW : -. RF : AUTO PAL SECAM NT4.43

-. A/V : AUTO PAL SECAM NT4.43 NT3.58"?" B/G D/K I

1 0CB : - RF : PAL ONLY

- A/V : AUTO PAL NT4.43 NT3.58B/G ONLY (NO OSD)

Indonesia/Thailand/

India

1 1CS: - RF : AUTO PAL SECAM NT4.43 NT3.58

-A/V : AUTO PAL SECAM NT4.43 NT3.58

"?" B/G D/K I

NT- M

Vietnam

Malaysia

SZM -173ET (16K) : Z90203 WITHOUT LINE STEREO

SZM -173EV (24K) : Z90234 WITH LINE STEREO

Function Required : 1. PICTURE OFF (after 15 minutes) during no signal. 2. AUDIO MUTE during no signal.

BLUE SCREEN ON/OFF. 4. TIMER (CLOCK ON/OFF). 5. No CHILD LOCK

3.

Existing sharpness level(when using the TDA6108 RGB AMP)

Sharpness level up (when using theTDA6107Q RGB AMP) MUST = HIGH

CLOCK DISPLAY OFF CLOCK DISPLAY ON Indonesia ONLY : HIGH

MUST = HIGH

BASIC = HIGH

BASIC = HIGH

MUST = LOW

DESTINATION LINE-STREEO MONO(TV-OUT) MONO(MONO-OUT)

OPTION-

BYTE

Vietnam / Malaysia

Indonesia (CB MODEL CLOCK ON)

Thailand (CB MODEL)

India (CB MODEL AFT OFF)

India (CS MODEL AFT OFF)

BYTE 0 BYTE 1 BYTE 0 BYTE 1 BYTE 0 BYTE 1

DF

DF

DD

DD

D8

DA

B8

B8

5F

5D

5D

_ _ _ _

58

5A

58

385F

5F

5D

5D

5F B8

D8

DA

D8

NTSC : 25KHz (NTSC TABLE)PAL : 50KHz (PAL TABLE)

NTSC : 25KHz (NTSC TABLE)PAL : 27KHz (PAL TABLE)

_



4-2-4 (F) TTX MICOM (SZM-175EA/EP) OPTION BYTE (FOR MIDDLE EAST ASIA)

BYTE BIT LOW (0) HIGH (1) Application MICOM

BYTE

0

D7 NOT USED ALL = LOW

D6TV : NORMAL ZOOM 16:9

A/V : NORMAL ZOOM


A/V : NORMAL ZOOM 16:9MUST = LOW

D5 NOT USED ALL = LOW

D4CH Up/down functional in

the A/V Mode (SCART Jack)



Africa : SCART

Others : RCA


D 2

D 1

D0 TDA8374A T D A 8842

BYTE

1

D7

NOT USED ALL (FIX = LOW)D6

D5

D4

Existing sharpness level

(when using the TDA6108

RGB AMP)

Sharpness level up

(when using the TDA6107Q RGB

AMP)

ALL (BASIC = HIGH)

TEST Unnecessary

D3 No Auto Power On Auto Power On ALL (BASIC = HIGH)

D2NTSC : 25 KHz (NTSC TABLE)


NTSC : 25 KHz (NTSC TABLE)

PAL : 27 KHz (NTSC TABLE)

D1MUST = HIGH

D0

D2 D1 COLOR SYSTEM S O U N D S Y ST E M R emar k

0 0 CK : AUTO (NO OSD) B /G D /K

N o sou nd

system in the A/V

M O D E

0 1CW : RF : AUTO PAL SECAM NT4.43

A/V : AUTO PAL SECAM NT4.43 NT3.58B /G D /K I

1 0CB : RF : PAL ONLY (NO OSD)

A/V : AUTO PAL NT4.43 NT3.58B /G O N L Y ( N O O S D)

1 1CS : RF : AUTO PAL SECAM NT4.43 NT3.58

A/V : AUTO PAL SECAM NT4.43 NT3.58

B /G D /K I

N T M

Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 2. AUDIO MUTE (during no signal) 3. No BLUE SCREEN

4. No TIMER 5. No CHILD LOCK

OSD language by micom

1. Persian (for Iran) : SPM-175EP : English/Persian (Iranian)

2. Arab (Middle East, Africa) : SPM-175EA : English/French/Arabian

MP

OPTION

BYTE

Destination Application MICOM BYTE0 BYTE1

Iran (Persian TTX) SPM-175EP 1F 1B

Middle East (except Iran)

SPM-175EA

1F 1B

Africa 07

"?"

"?"

"?"

D1 D0 00 01 10 11

B/G D/K I ?

Singapore 17

1B

1B

Australia / Newzealand 1D 18



4-2-4 (G) TTX MICOM (SPM-175EE/ER/EG/EU) OPTION BYTE (FOR EUROPE)


BYTE

0

D7 3 BAND UHF DNLY (UK only)

D6TV : NORMAL ZOOM 16:9

A/V : NORMAL ZOOM


A/V : NORMAL ZOOM 16:9

D5< P O L A N D O P TIO N >

R 913 : 680 added. J901 : D elete

D4CH Up/Down functional in the


CH Up/Down not functional in

the A/V Model (RCA Jack)MUST = LOW

D3 P-STD NORMAL P-STD MAX MUST = LOW

D 2

D 1

D0 TDA8374A TDA8842

BYTE

1

D7 NOT USED

D6 PAL/SECAM SECAM - L HIGH (CF only)

D5E nglish/G er m an/F rench/D utch/

Italian/Spanish/Swedish

English/Croatian/Romanian/

Hungarian/Polish/Czech

This bit is only applied to

SPM-175EE

D4

Existing sharpness level

(when using the TDA6108RGB AMP)

Sharpness level up

(when using the TDA6107Q AMP)TEST Unnecessary


D2NT SC : 25K H z (NT SC T A B LE )

P A L : 50K H z (P A L T A B LE )

NT SC : 25K H z (NT SC T A B LE )

P A L : 27K H z (NT SC T A B L E )ALL (RF VOL. CURVE) BASIC = LOW

D1 MUST = LOW

D0

D2 D1 SOUND SYSTEM COLOR SYSTEM Remark

0 0 "?" B/G D/K : CK MODEL

AUTO

(NO OSD)

No SOUND SYSTEM

in the A/V Mode

0 1 I ONLY (NO OSD) : CI,CII MODEL

1 0 B/G ONLY (NO OSD): CB,CX MODEL

1 1 NOT USED

Destination Application MICOM BYTE 0 BYTE 1 LANGUAGE

MP

OPTION

BYTE

United Kingdom (CI)

SPM-175EE

83 18

See BYTE 1 D5Other Western Europe (CB) 05 18

Eastern Europe (CK) 01 38

France/Swiss SPM-175EU 05 58

Yugo/Greece SPM-175EG 05 18 English/Yugo/Greek

Russia/BulgariaSPM-175ER

01 19 English/Russian/Bulgarian

P-STD Classification (CON/BRI/SHRP/COL)

D3 BIT STANDARD MODE DYNAMIC MODE MOVIE MODE MILD MODE CUSTOM MODE

0 90/50/50/50 100/50/50/50 75/55/50/50 60/50/50/50 90/55/25/50

Function Required :1. PICTURE OFF (after 15 minutes) during no signal. 2. AUDIO MUTE (during no

3. No BLUE SCREEN. 4. No TIMER (CLOCK /OFF). 5. No CHILD LOCK

signal).

MUST = LOW

ALL BASIC = HIGH

ALL BASIC = HIGH

Ireland (CII) 03 18

FIX = LOW

B/G D/K 175ER is only applied (Others = LOW)

Russia 11 19 Russian (Rca - 4pin)


No 1 2 3 4 5 6 7 8

OPTI

ON

Fact

ory

Mod

e Li

st

ZOOM

MOD

E

LAN

GUAG

E

AREA

POW

ER

SYST

EM(S

OUN

D)

AV-IN

/OUT

VOLU

ME

TBL

AFT

Opt

ion

Sele

te

16:9

OFF

16:9

ON

EURO

P

RUSS

IA

GREE

K

WES

T

EAST

ON OFF

CF CI CK CX CB CII

SCAR

T

RCA

PAL

NTS

C

ON OFF

Func

tion

NOR

MAL

Z

OOM

NOR

MAL

ZOOM

16:

9

WES

T : E

nglis

h/Ge

rman

y/Fr

ench

/Dut

ch/S

pani

sh/It

aly/

Swed

ish

EAST

: E

nglis

h/Cz

echo

/Cro

/Rom

ania

/Hun

gary

/Pol

and

Engl

ish

R

ussi

an

Bu

lgar

ia (M

ust A

rea

Optio

n W

est)

Engl

ish

Y

ugos

lavi

a

Gr

eek(

Mus

t Are

a Op

tion

Wes

t)

Engl

ish

G

erm

any

Fren

ch

Du

tch

S

pani

sh

Ita

ly

Sw

edis

h

Engl

ish

C

zech

o

Cro

Rom

ania

Hung

ary

P

olan

d

Dire

ct P

ictu

re O

n

Pict

ure

Stan

d By

Mod

e

OSD

N

o Di

spla

y

OSD

N

o Di

spla

y(PA

L-I,N

T4.4

3,N

TPB,

UHF

Only,

Engl

and

Only

)

?

B/G

D/K(

PAL,

SECA

M-B

/G,D

/K,N

T4.4

3,N

TPB)

OSD

N

o Di

spla

y

OSD

N

o Di

spla

y(PA

L0B/

G,N

T4.4

3,N

TPB)

OSD

N

o Di

spla

y

A/V

Mod

e CH

-Up/

dow

n Po

ssib

iliy(

SCAR

T Ja

ck)

A/V

Mod

e CH

-Up/

dow

n Im

poss

ibili

ty(R

CA J

ack)

NTS

C: 2

5KHz

(NTS

C Ta

ble)

, PAL

: 27K

Hz (N

TSC

Tabl

e)

NTS

C: 2

5KHz

(NTS

C Ta

ble)

, PAL

:50K

Hz(P

AL T

able

)

Alw

ays

AFT

OnAf

ter F

ine

Tune

ing

AFT

Off

Rem

arks

M

ust O

n (Tr

ansm

itter

P.SI

ZE O

ptio

n)

De

stin

atio

n Op

tion

W

este

rn E

urop

e De

stin

atio

n

Ea

ster

n Eu

rope

Des

tinat

ion

M

ust O

n (M

aste

r Sw

itch

Optio

n)

Fr

ance

, Sw

itzer

land

En

glan

d

Eu

rope

, Rus

sia

N

ot U

sed

W

este

rn E

urop

e

Ire

land

M

ust S

cart

M

ust P

AL

M

ust O

n(Ch

anne

l Cha

nge

& P

ictu

re O

ff/On

)

1. N

o Si

gnal

AFT

ER 1

5-M

in P

ictu

re O

ff

2. N

o Si

gnal

Aud

io M

ute

3. W

ithou

t Blu

e Sc

reen

4. W

ithou

t Tim

er

5. W

ithou

t Chi

ld L

ock

6. M

ust

Help

Fu

nctio

n

4-2-4 (H) SPM-515XX PAINTER MICOM



No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Loc.

C806

C813

C816

C905

C919

C922

C926

C928

CP01

CP02

CT04

CT06

CT07

D908

D909

D910

DT01

DT02

DT03

DZ90

8

DZ80

6

DZP0

1

2201

-000

446

PHIL

IPS

ETT(

OTP

/MA

SK )

Part

No

Des

crip

tion;

Spec

ifica

tion

C-CE

RA,D

ISC:

332,

400

V

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

2401

-000

603

2401

-001

333

C-AL

;1uF

,50V

C-AL

;470

nF,2

0%,5

0V

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

2202

-000

796

2305

-000

412

C-CE

RA,A

XIAL

;102

,50V

C-CE

RA,A

XIAL

;104

,50V

2202

-002

037

2202

-002

037

C-CE

RA,A

XIAL

;100

nF,5

0V

C-CE

RA,A

XIAL

;104

,50V

2401

-002

144

C-AL

;47u

F,16V

* *

* *

* *

* *

* *

3812

-000

219

0401

-000

005

WIR

E-N

O SH

EATH

;JUM

PER

DIOD

E-SW

ITCH

ING;

1N41

48

2001

-000

252

R-CA

;1.6

Kohm

,1/8

W,A

A

2001

-000

252

R-CA

;1.6

Kohm

,1/8

W,A

A

2001

-000

252

R-CA

;1.6

Kohm

,1/8

w,A

A

* *

* *

* *

* *

* *

0403

-000

355

DIOD

E-ZE

NER

;UZB

5.1B

* *

* *

* *

* *

* *

2201

-000

446

PHIL

IPS

PAIN

TER(

OTP

/MA

SK )

Part

No

Des

crip

tion;

Spec

ifica

tion

C-CE

RA,D

ISC:

332,

400

V

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

2202

-000

796

2401

-002

144

C-CE

RA,A

XIAL

;102

,50V

C-AL

;47u

F,16V

2202

-002

037

2401

-001

914

C-CE

RA,A

XIAL

;104

,50V

C-AL

;1uF

,50V

,NP

2401

-002

235

C-AL

;10u

F,16V

* *

* *

* *

* *

* *

0401

-000

05DI

ODE-

SWIT

CHIN

G;1N

4148

2001

-000

281

R-CA

;1.6

Kohm

,1/8

W,A

A

2001

-000

281

R-CA

;1.6

Kohm

,1/8

W,A

A

2001

-000

81R-

CA;1

.6Ko

hm,1

/8w

,AA

* *

* *

* *

* *

* *

2202

-000

127

C-C,

AXIA

L;10

3(10

nF),2

5V

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

0403

-002

96DI

ODE-

ZEN

ER;M

TZ5.

6B

* *

* *

* *

* *

* *

0403

-000

563

DIOD

E-ZE

NER

;MTZ

9.1B

0403

-000

296

DIOD

E-ZE

NER

;MTZ

5.6B

Rem

ark

In

serte

d in

the

oppo

site

pol

arity

: To

avoi

d 1-

chip

IC o

ut w

hen

perfo

rmin

ga

forc

ed d

isch

arge

test

on

1091

5D

Sa

me

as D

ZP01

(109

15D

UP-V

ERSI

ON P

CB)

On

ly 1

0915

E PC

B ap

plie

s

4-2-4 (I) DIFFERENCE WHEN APPLYING PHILIPS PAINT MICOM



No 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Loc.

IC90

1

J149

J175

J176

J178

J182

J190

J194

J273

J274

J802

JP01

JP02

JP03

JP04

JP05

JT01

L904

LT01

LT02

PHIL

IPS

ETT(

OTP

/MA

SK )

Part

No

Des

crip

tion;

Spec

ifica

tion

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

2001

-000

857

R-CA

;560

0HM

,1/8

W,A

A

* *

* *

* *

* *

* *

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

* *

* *

* *

* *

* *

2901

-000

297

FILT

ER-E

MI O

N B

OARD

;3A

2001

-000

793

PHIL

IPS

PAIN

TER(

OTP

/MA

SK )

Part

No

Des

crip

tion;

Spec

ifica

tion

R-CA

;47o

hm,1

/8W

,AA

2701

-000

211

INDU

CTOR

-AXI

AL;6

8uH

2001

-000

734

R-CA

;4.7

Kohm

,1/8

W,A

A

* *

* *

* *

* *

* *

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

2202

-002

037

C-CE

RA,A

XIAL

;104

,50V

Rem

ark

See

Diff

eren

ce in

S15

A M

icom

Tab

le

See

Diff

eren

ce in

S15

A M

icom

Tab

le

2001

-000

857

R-CA

;560

0HM

,1/8

W,A

A

2001

-000

857

R-CA

;560

0HM

,1/8

W,A

A

2001

-000

869

R-CA

;56o

hm,1

/8W

,AA

2001

-000

793

R-CA

;47o

hm,1

/8W

,AA

2001

-000

869

R-CA

;56o

hm,1

/8W

,AA

2001

-000

793

R-CA

;47o

hm,1

/8W

,AA

2001

-000

869

R-CA

;56o

hm,1

/8W

,AA

2701

-000

114

INDU

CTOR

-AXI

AL;1

0uH

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

2901

-000

297

FILT

ER-E

MI O

N B

OARD

;3A

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

* *

* *

* *

* *

* *

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

2306

-000

122

C-FI

LM,M

PPF;

100N

F,50V

4-2-4 (J) DIFFERENCE WHEN APPLYING PHILIPS PAINT MICOM



No 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

Loc.

LT03

QP01

R820

R821

R907

R908

R909

R933

R936

R938

R940

R944

R948

R957

R959

RP01

RP02

RT01

RT02

RT03

RT04

PHIL

IPS

ETT(

OTP

/MA

SK )

Part

No

Des

crip

tion;

Spec

ifica

tion

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

2001

-000

252

R-CA

;1.6

KOHM

,1/8

W,A

A

2008

-001

013

PHIL

IPS

PAIN

TER(

OTP

/MA

SK )

Part

No

Des

crip

tion;

Spec

ifica

tion

R-FU

S(S)

;1.2

OHM

,2W

,AF

2001

-000

290

R-CA

;10K

ohm

,1/8

W,A

A

2701

-000

114

INDU

CTOR

-AXI

AL;1

0uH

Rem

ark

2001

-000

857

R-CA

;560

0HM

,1/8

W,A

A

2001

-000

449

R-CA

;2.2

KOHM

,1/8

W,A

A

1203

-001

752

IC-R

EG;L

F33C

V

2001

-000

221

R-CA

;1.2

Kohm

,1/8

W,A

A

2001

-000

006

R-CA

;2.4

Kohm

,1/8

W,A

A

2001

-000

613

R-CA

;3.9

Kohm

,1/8

W,A

A

2001

-000

290

R-CA

;10K

ohm

,1/8

W,A

A

2001

-000

734

R-CA

;4.7

KOHM

,1/8

W,A

A

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

2001

-000

007

R-CA

;3Ko

hm,1

/8W

,AA

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

0403

-000

296

DIOD

E-ZE

NER

;MTZ

5.6B

0403

-000

296

DIOD

E-ZE

NER

;MTZ

5.6B

2001

-000

539

R-CA

;24K

ohm

,1/8

W,A

A

* *

* *

* *

* *

* *

2701

-000

114

INDU

CTOR

-AXI

AL;1

0uH

* *

* *

* *

* *

* *

2001

-000

449

R-CA

;2.2

KOHM

,1/8

W,A

A

2001

-000

591

R-CA

;3.3

KOHM

,1/8

W,A

A

2001

-000

786

R-CA

;47K

OHM

.1/8

W,A

A

2001

-000

006

R-CA

;2.4

KOHM

,1/8

W,A

A

2001

-000

660

R-CA

;33K

OHM

,1/8

W,A

A

2001

-000

800

R-CA

;5.1

KOHM

,1/8

W,A

A

2001

-000

563

R-CA

;27K

OHM

,1/8

W,A

A

2001

-000

577

R-CA

;2KO

HM,1

/8W

,AA

2008

-001

062

R-FU

S(S)

;390

HM,2

W,A

F*

* *

* *

* *

* *

*

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

0403

-000

551

DIOD

E-ZE

NER

;MTZ

3.9B

2001

-000

241

R-CA

;1.5

Kohm

,1/8

W,A

A

* *

* *

* *

* *

* *

4-2-4 (K) DIFFERENCE WHEN APPLYING PHILIPS PAINT MICOM



Loc.

Part

No

Loc.

Part

No

1C4

0923

06-0

0032

7C-

F,M

PPF;

6.3n

F,1.

6KV,

TPCR

402S

2306

-000

327

C-F,

MPP

F;6.

3nF,

1.6K

V,TP

LOC.

NO

2C4

1022

01-0

0098

4C-

C,DI

SC;0

.68n

F,2k

V CR

401S

2201

-000

984

C-C,

DISC

;0.6

8nF,

2kV,

TPLO

C.N

O 3

C413

2305

-000

382

C-F,

MPE

F;4.

7nF,

400V

,TP

CR40

4S23

05-0

0038

2C-

MPE

F;4.

7nF,

400V

,TP

LOC.

NO

4C4

1623

06-0

0019

5C-

F,M

PPF;

360n

F,40

0V,T

PCR

405S

LOC.

NO

5C4

20CR

406S

2306

-000

193

C-M

PPF;

360n

F,20

0V,T

PLO

C.N

O &

SPE

C ch

ange

6C4

1922

01-0

0098

4C-

C,DI

SC;0

.68n

F,2k

V,TP

CR40

3S22

01-0

0098

4C-

C,DI

SC;0

.68n

F,2k

V,TP

LOC.

NO

Chan

ge

7C6

0224

01-0

0003

0C-

AL;2

2uF,

25V,

GP,T

PC6

0224

01-0

0066

0C-

AL;2

.2uF

,50V

,TP

8C6

05C6

0523

01-0

0019

2C-

PEF;

1nF,

50V,

TP

9C8

0023

06-0

0032

1C-

F,M

PPF;

470N

F,27

5V,T

P CX

801S

2306

-000

321

C-M

PPF;

470N

F,27

5V,T

PLO

C.N

O

10C8

0323

01-0

0022

4C-

F,PE

F;22

nF,5

0V,T

P C8

0623

01-0

0022

4C-

FILM

,PEF

;22n

F,5%

,50V

,TP

LOC.

NO

11C8

0422

01-0

0014

4C-

C,DI

SC;0

.1nF

,50V

,TP

C804

2301

-000

235

C-PE

F;3.

9nF,

5%,5

0V,T

P

12C8

0523

03-0

0016

3C-

F,PP

F;2.

2nF,

800V

,TP

C805

2301

-001

342

C-PP

F;1.

5nF,

5%,8

00V,

TP

13C8

0622

01-0

0044

6C-

C,DI

SC;3

.3nF

,400

V TP

CY80

4S22

01-0

0044

6C-

C,DI

SC;3

.3nF

,20%

,400

V,TP

14C8

03C8

0323

01-0

0066

5C-

PEF;

100n

F,5%

,63V

,TP

15C8

1124

01-0

0314

1C-

AL;2

200u

F,25

V,W

T,TP

C8

1124

01-0

0221

5C-

AL;2

200u

F,20

%,2

5V,T

P

16C8

12C8

1222

01-0

0037

6C-

C,DI

SC;0

.22n

F,5%

,50V

,TP

17CN

501

AA39

-201

09B

L,C-

ASSY

;YBN

H025

-08,

8P,5

00CN

501A

AA39

-201

09B

L,C-

ASSY

;YBN

H025

-08,

S,8P

,500

LOC.

NO

18CN

602

3711

-002

643

C-HE

ADER

;BOX

,4P,

SNCN

602

3711

-000

963

C-HE

ADER

;BOX

,4P,

STRA

IGHT

,SN

ONLY

S4 M

ODEL

19CN

802

AA27

-200

04A

COIL

-DEG

AUSS

ING;

LC80

1SAA

27-2

0003

ZC-

DEGA

USSI

NG;

21,1

3.5o

hm,E

20D4

0704

02-0

0013

2D-

REC;

1N40

04,4

00V,

TP

21D6

0104

01-0

0000

5D-

SW;1

N41

48,1

00V,

200M

A,TP

ONLY

TDA7

266S

S-AM

P22

D602

0401

-000

005

D-SW

;1N

4148

,100

V,20

0MA,

TPON

LY T

DA72

66S

S-AM

P23

D800

1405

-000

187

VARI

STOR

;750

V,12

50A,

TPVX

801S

1405

-000

187

VARI

STOR

;750

V,12

50A,

TPLO

C.N

O 24

D801

S04

02-0

0111

1D-

REC;

1N53

97GP

,600

V,TP

25D8

02S

0402

-001

111

D-RE

C;1N

5397

GP,6

00V,

TP

26D8

03S

0402

-001

111

D-RE

C;1N

5397

GP,6

00V,

TP

27D8

04S

0402

-001

111

D-RE

C;1N

5397

GP,6

00V,

TP

28D8

0204

02-0

0054

0D-

REC;

RU20

A,60

0V,1

.5A

D807

0402

-000

540

D-RE

C;RU

20A,

600V

,TP

LOC.

NO

29D8

03AA

96-0

0111

GAS

SY-H

/S;A

A62-

3001

3L,F

ML-

G02S

D811

AA96

-002

43A

ASSY

H/S;

YG91

1S2R

LOC.

&Pa

rtsCh

ange

d30

D804

0402

-001

111

D-RE

C;1N

5397

GP,6

00V,

TPD8

0604

02-0

0111

1D-

REC;

1N53

97GP

,600

VLO

C.N

O

31D8

0804

01-0

0000

5D-

SW;1

N41

48,1

00V,

200M

A

32DZ

303

0403

-000

699

D-ZE

NER

;TZP

27B,

27V

OPTI

ON

1091

5C PC

B VER

SION

1091

5E PC

B VER

SION

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

0402

-000

102

D-BR

IDGE

;D2S

B60,

600V

,1.5

A

* * * *

* * * *

* * * *

No

* * * *

* * * *

* * * *

* * * *

* * * *

* * * *

D801

Rem

ark

Des c

riptio

nDe

s crip

tion

Sect

ion

Chan

ge o

nly

whe

n TD

A726

6S is

used

.Ad

d on

ly w

hen

TDA7

266S

is us

ed.

Chan

ge

LOC.

NO

Chan

ge

Chan

ge

Chan

ge

Chan

ge

LOC.

NO

Chan

ge

Chan

ge

LOC.

NO

Chan

ge

Chan

ge

Chan

ge

Chan

ge

Chan

geCh

ange

Sigu

lariz

e th

e po

wer

supp

ly

Add

coun

term

easu

res

on S

URGE

Add

coun

term

easu

res

on S

URGE

Sche

mat

icch

ange

sm

ade

New

Part

New

Part(

Dula

izeth

eex

istin

gdi

ode)

4-2-4 (L) 915C VS 915E PCB DIFFERENCE LIST



Loc.

Part

NoLo

c.Pa

rt No

1091

5C P

CB V

ERSI

ON10

915E

PCB

VER

SION

No 33DZ

602

0403

-000

508

D-ZE

NER

;MTZ

J5.6

BON

LY T

DA72

66S

S-AM

P34

DZ80

804

03-0

0030

0D-

ZEN

ER;M

TZ8.

2BDZ

801

0403

-000

658

D-ZE

NER

;MTZ

18A,

18V

35DZ

804

2001

-001

170

R-CA

(S);6

.8OH

M,1

/2W

,AA

DZ80

404

03-0

0069

9D-

ZEN

ER;T

ZP27

B,27

V

36DZ

805

0403

-000

563

D-ZE

NER

;MTZ

9.1B

,9.1

V

37DZ

809

DZ80

904

03-0

0029

4D-

ZEN

ER;M

TZ4.

7B,4

.7V

38DZ

904

0403

-000

508

D-ZE

NER

;MTZ

J5.6

B,5.

6V

39EL

601

EL60

3AA

60-4

0011

BEY

ELET

;ID2.

2,OD

3.2,

BSP

40EL

602

EL60

4AA

60-4

0011

BEY

ELET

;ID2.

2,OD

3.2,

BSP

41EY

303

AA60

-400

11A

EYEL

ET;ID

2.0,

OD2.

8EL

601

AA60

-400

11B

EYEL

ET;ID

2.2,

OD3.

2,BS

P

42EY

304

AA60

-400

11A

EYEL

ET;ID

2.0,

OD2.

8EL

602

AA60

-400

11B

EYEL

ET;ID

2.2,

OD3.

2,BS

P

43EY

804

AA60

-400

11A

EYEL

ET;ID

2.0,

OD2.

8

44EY

816

AA60

-400

11A

EYEL

ET;ID

2.0,

OD2.

8

45EY

817

AA60

-400

11A

EYEL

ET;ID

2.0,

OD2.

8

46EY

818

AA60

-400

11A

EYEL

ET;ID

2.0,

OD2.

8

47EY

820

AA60

-400

11A

EYEL

ET;ID

2.0,

OD2.

8

48EY

821

AA60

-400

11A

EYEL

ET;ID

2.0,

OD2.

8

49F8

0136

01-0

0026

1FU

SE-C

ARTR

IDGE

;250

V,3.

15A

FP80

1S36

01-0

0026

1FU

SE-C

ARTR

IDGE

;250

V,3.

15A

LOC.

NO

Chan

ge50

F802

3601

-001

086

FUSE

-AXI

AL L

EAD;

125V

,5A

RF80

036

01-0

0108

6FU

SE-A

XIAL

LEA

D;12

5V,5

ALO

C.N

O Ch

ange

51HC

101

AA13

-200

04W

IC-H

YBRI

D;PA

P103

T,SI

P,6P

HC10

1SAA

13-2

0004

WIC

-HYB

RID;

PAP1

03T,

SIP,

6P,T

PLO

C.N

O Ch

ange

52IC

201

1204

-001

440

IC-V

IDEO

;TDA

8842

,DIP

,56P

IC20

1S12

04-0

0144

0IC

-VID

EO;T

DA88

42,D

IP,5

6PLO

C.N

O Ch

ange

53IC

602

AA96

-503

07A

ASSY

-H/S

;SOU

ND,

TDA7

057A

QIC

602

AA96

-002

44B

ASSY

H/S

;TDA

7266

SAM

P C

hang

ed54

IC80

1AA

96-5

0298

CAS

SY-H

/S;P

OWER

,KA3

S068

0IC

801S

AA96

-002

42A

ASSY

H/S

;KA5

Q076

5RLO

C. &

Par

ts c

hang

ed

New

Par

t55

J111

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

J111

2001

-000

969

R-CA

;75O

HM,1

/8W

,AA

OPTI

ON56

J143

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

57J1

49J1

4938

12-0

0021

9W

IRE-

NO

SHEA

TH;J

UMPE

R

58J1

6320

01-0

0001

9R-

CA(S

);10O

HM,1

/2W

,AA,

TPJ1

6338

12-0

0021

9W

IRE-

NO

SHEA

TH;J

UMPE

R

59J1

6838

12-0

0021

9W

IRE-

NO

SHEA

TH;J

UMPE

R

60J1

7138

12-0

0021

9W

IRE-

NO

SHEA

TH;J

UMPE

R

61J1

8920

01-0

0001

9R-

CA(S

);10O

HM,1

/2W

,AA,

TP

62J2

22J2

2638

12-0

0021

9W

IRE-

NO

SHEA

TH;J

UMPE

R

63J2

7138

12-0

0021

9W

IRE-

NO

SHEA

TH;J

UMPE

R

64J2

7238

12-0

0021

9W

IRE-

NO

SHEA

TH;J

UMPE

R

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

NT8

01S

EYEL

ET

D801

BRI

DGE

DIOD

E DE

L

ONLY

TDA

7056

B S-

AMP

TDA7

057A

Q TD

A726

6S

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

Sect

ion

Des c

riptio

nRe

mar

k

Sigu

lariz

e th

e po

wer

sup

ply

Des c

riptio

n

4-2-4 (M) 915C VS 915E PCB DIFFERENCE LIST



Loc.

Part

NoLo

c.Pa

rt No

1091

5C P

CB V

ERSI

ON10

915E

PCB

VER

SION

No 65J2

7338

12-0

0021

9W

IRE-

NO

SHEA

TH;J

UMPE

R66

J274

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

67L1

0227

01-0

0021

2IN

DUCT

OR-A

XIAL

;68u

HL1

0227

01-0

0017

8IN

DUCT

OR-A

XIAL

;33u

H68

L401

AA27

-300

01B

C-LI

NEA

RLIT

Y;19

5uH,

QIC1

010

LR40

1SAA

27-3

0001

BC-

LIN

EARL

ITY;

195u

H,QI

C101

0LO

C.69

L801

AA29

-300

01D

F-LI

NE

NOI

SE;S

Q191

3,6.

0MH,

0.8A

LX80

1SAA

29-3

0001

DF-

LIN

E N

OISE

;SQ1

913,

6.0M

H,0.

8ALO

C.70

L804

3301

-000

287

C-F,

BEAD

;AA,

3.5x

1.0x

6.0m

mL8

0233

01-0

0122

3C-

F,BE

AD;A

B,3.

5X5X

0.8M

M71

L803

3301

-001

223

C-F,

BEAD

;AB,

3.5X

5X0.

8MM

72L9

03

73N

T801

1404

-001

075

THER

MIS

TOR-

NTC

;5oh

m,1

7mW

/C,T

PN

T801

S14

04-0

0107

5TH

ERM

ISTO

R-N

TC;5

ohm

,17m

W/C

,TP

LOC.

74P8

0114

04-0

0104

8T-

PTC;

7ohm

,200

/220

V,27

0Vac

P801

S14

04-0

0104

8T-

PTC;

7ohm

,200

/220

VLO

C.75

PC80

106

04-0

0103

8PH

OTO-

COUP

LER;

TR,1

30-2

60%

,200

mW

PC80

1S06

04-0

0103

8PH

OTO-

COUP

LER;

TR,1

30-2

60%

,200

mW

LOC.

76Q8

0105

01-0

0218

3TR

-SM

ALL

SIGN

AL;K

TC90

14,N

PN77

R240

2001

-000

832

R-CA

;510

OHM

,1/8

W,A

A,TP

R240

2001

-000

362

R-CA

;150

OHM

,1/8

W,A

A,TP

78R6

0420

01-0

0073

4R-

CA;4

.7KO

HM,1

/8W

,AA,

TPR6

0420

01-0

0086

4R-

CA;5

6KOH

M,1

/8W

,AA,

TP79

R605

2001

-000

563

R-CA

;27K

OHM

,1/8

W,A

A,TP

R605

2001

-000

734

R-CA

;4.7

KOHM

,1/8

W,A

A,TP

80R6

0620

01-0

0072

3R-

CA;4

.3KO

HM,1

/8W

,AA,

TPR6

0620

01-0

0000

8R-

CA;1

5KOH

M,1

/8W

,AA,

TP81

R610

2001

-000

563

R-CA

;27K

OHM

,1/8

W,A

A,TP

R610

2001

-000

734

R-CA

;4.7

KOHM

,1/8

W,A

A82

R611

2001

-000

723

R-CA

;4.3

KOHM

,1/8

W,A

A,TP

R611

2001

-000

008

R-CA

;15K

OHM

,1/8

W,A

A,TP

83R7

0720

01-0

0042

9R-

CA;1

KOHM

,1/8

W,A

A84

R803

2004

-001

373

R-M

FI;1

00Ko

hm,1

/2W

,AA,

TPR8

0320

01-0

0110

8R-

CA;2

2KOH

M,1

/2W

,AA,

TP85

R804

2001

-001

170

R-CA

;6.8

OHM

,1/2

W,A

A,TP

86R8

0520

04-0

0196

7R-

MFI

;68K

ohm

,1/2

W,A

A,TP

R805

2001

-001

170

R-CA

RBON

(S);6

.8OH

M,1

/2W

,AA

87R8

0620

02-0

0101

1R-

COM

P;3.

3Moh

m,1

/2W

,AA,

TPRY

802S

2002

-001

011

R-CO

MPO

SITI

ON;3

.3M

ohm

,1/2

W,A

ALO

C.88

R807

2002

-001

011

R-CO

MP;

3.3M

ohm

,1/2

W,A

A,TP

RY80

1S20

02-0

0101

1R-

COM

POSI

TION

;3.3

Moh

m,1

/2W

,AA

LOC.

89R8

0720

01-0

0010

9R-

CARB

ON(S

);470

OHM

,1/2

W,A

A90

R810

2003

-000

527

R-M

OX(S

);18K

ohm

,2W

,AA,

TPR8

1020

03-0

0065

4R-

MOX

(S);3

3Koh

m,2

W,A

A91

R811

R811

2001

-000

019

R-CA

RBON

(S);1

0OHM

,1/2

W,A

A92

R812

2003

-000

455

R-M

OX;1

00oh

m,2

W,A

A,TP

R812

2003

-000

713

R-M

ETAL

OXI

DE(S

);47o

hm,2

W,A

F93

R813

R813

2001

-001

088

R-CA

RBON

(S);1

KOHM

,1/2

W,A

A,TP

94R8

1420

08-0

0107

3R-

FUS(

S);0

.68o

hm,2

W,A

A,TP

R814

2009

-001

011

R-M

ETAL

PLA

TE;0

.18o

hm,5

W,C

L,TP

95R8

1520

08-0

0107

3R-

FUS(

S);0

.68o

hm,2

W,A

A,TP

R815

2009

-001

011

R-M

ETAL

PLA

TE;0

.18o

hm,5

W,C

L,TP

96R8

24R8

2420

01-0

0119

2R-

CARB

ON(S

);820

OHM

,1/2

W,A

A

* *

* *

* *

* *

* *

* *

PAIN

TER:

10UH

, OTH

ERS

MIC

OM:J

UMPE

R

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

1/2W

360

OR

DELE

TE (O

PTIO

N)

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

1/2W

360

OR

DELE

TE (O

PTIO

N)

Sect

ion

Rem

ark

Chan

ged

Chan

ged

Chan

ged

Chan

ged

Chan

ged

Chan

ged

Chan

ged

Add

coun

term

easu

res

on S

URGE

Diffe

renc

e be

twee

n so

und

outp

uts

Appl

ied

to m

odel

S4

(onl

y)Ap

plie

d to

mod

el S

4 (o

nly)

Desc

riptio

nDe

scrip

tion

4-2-4 (N) 915C VS 915E PCB DIFFERENCE LIST



Loc.

Part

NoLo

c.Pa

rt No

1091

5C P

CB V

ERSI

ON10

915E

PCB

VER

SION

No 97

R826

2003

-000

713

R-M

ETAL

OXI

DE(S

);47o

hm,2

W,A

F

98R8

2720

04-0

0139

9R-

MET

AL(S

);5.1

Kohm

,1/2

W,A

A

99R8

2920

01-0

0073

4R-

CARB

ON;4

.7KO

HM,1

/8W

,AA

100

R910

2001

-000

290

R-CA

;10K

OHM

,1/8

W,A

A,TP

R910

2001

-000

429

R-CA

RBON

;1KO

HM,1

/8W

,AA

101

R944

3812

-000

219

WIR

E-N

O SH

EATH

;JUM

PER

102

R950

R950

2001

-000

429

R-CA

RBON

;1KO

HM,1

/8W

,AA

103

RW70

220

11-0

0109

8R-

NET

WOR

K;75

/75/

1K/7

5ohm

,1/8

W

104

RX80

120

02-0

0101

1R-

COM

P;3.

3Moh

m,1

/2W

,AA,

TPRX

801S

2002

-001

011

R-CO

MPO

SITI

ON;3

.3M

ohm

,1/2

W,A

ALO

C.10

5SF

N02

2904

-001

086

FILT

ER-S

AW A

V;38

.9M

HzSF

101S

2904

-001

086

F-SA

W A

V;38

.9M

Hz,S

IP5K

,TP,

18dB

LOC.

106

SW80

134

03-0

0017

9SW

ITCH

-PUS

H;25

0V,5

A,DP

STSW

801S

3403

-000

179

SWIT

CH-P

USH;

250V

,5A,

DPST

LOC.

107

T444

AA26

-300

01Y

T-FL

YBAC

K;FS

V-20

A001

,20,

125V

T444

SAA

26-3

0001

YT-

FLYB

ACK;

FSV-

20A0

01,2

0,12

5VLO

C.10

8T8

01AA

26-2

0006

UT-

SWIT

CHIN

G;90

-260

VT8

01S

AA26

-000

43A

T-SW

ITCH

ING;

AC90

~260

VLO

C.10

9TU

01AA

40-0

0007

ATU

NER

-V/S

;TEC

C094

9VG2

9A(S

)TU

01S

AA40

-000

36A

TUN

ER;T

AEC-

G723

D,PA

L,TR

,181

CHLO

C.11

0V9

9937

04-0

0109

0S-

CRT;

9P,1

5.24

PI,2

6.5P

I,SN

V999

S37

04-0

0110

5S-

CRT;

11P,

20PI

,26.

5PI,N

ILO

C.11

1X9

0128

01-0

0372

8CR

YSTA

L-UN

IT;6

MHz

,30p

pm,2

0pF

X901

2801

-000

724

CRYS

TAL;

6MHz

,50p

pm,2

8-AA

M,2

0pF

112

Z207

Z207

2903

-000

277

F-CE

RAM

IC;B

P,6.

0MHz

,60K

Hz

113

Z210

2903

-000

200

FILT

ER-C

ERAM

IC;B

P,6.

5MHz

TPZ2

10*

* *

* *

* *

* *

* *

*

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

OPTI

ON*

* *

* *

* *

* *

* *

*

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

* *

OPTI

ON

Sect

ion

Rem

ark

New

Par

t (Du

laize

the

exis

ting

diod

e)

Diffe

rent

as

com

pare

d to

PAL

-I

Chan

ged

Chan

ged

Chan

ged

Chan

ged

Chan

ged

Chan

ged

Chan

ged

Desc

riptio

nDe

scrip

tion

4-2-4 (O) 915C VS 915E PCB DIFFERENCE LIST


Samsung Electronics Samsung Electronics

4-3 Other Adjustments

4-3-1 General

1. Usually, a color TV needs only slight touch-up adjustment upon installation. Check thebasic characteristics such as height, horizontaland vertical sync and focus.

2. The picture should have good black and whitedetails. There should be no objectionablecolor shading; if color shading is present, per-form the purity and convergence adjustmentsdescribed below.

3. Use the specified test equipment or its equiva-lent.

4. Correct impedance matching is essential.

5. Avoid overload. Excessive signal from a sweepgenerator might overload the front-end of theTV. When inserting signal markers, do notallow the marker generator to distort testresults.

6. Connect the TV only to an AC power sourcewith voltage and frequency as specified on thebackcover nameplate.

7. Do not attempt to connect or disconnect anywires while the TV is turned on. Make surethat the power cord is disconnected beforereplacing any parts.

8. To protect against shock hazard, use an isola-tion transformer.

4-3-2 Automatic Degaussing

A degaussing coil is mounted around the pic-ture tube, so that external degaussing aftermoving the TV should be unnecessary. Butthe receiver must be properly degaussed uponinstallation.

The degaussing coil operates for about 1 sec-ond after the power is switched ON. If the sethas been moved or turned in a different direc-tion, disconnect its AC power for at least 30minutes.

If the chassis or parts of the cabinet becomemagnetized, poor color purity will result. Ifthis happens, use an external degaussing coil.Slowly move the degaussing coil around thefaceplate of the picture tube and the sides andfront of the receiver. Slowly withdraw the coilto a distance of about 6 feet before removingpower.

4-2-5 RESET

The Reset Mode is used during factory inspection. Function Reset:

1. Channels Add/Erase2. Sort Non3. System Auto 4. Timer off5. Blue Screen off6. Child Lock off7. Picture standard8. Volume 109. CH. Skip Erased


Samsung Electronics


Samsung Electronics

4-3-3 High Voltage Check

CAUTION: There is no high voltage adjustment on this chassis.The B+ power supply must be set to +125 volts (Full color bar inputand normal picture level).

1. Connect a digital voltmeter to the secondanode of the picture tube.

2. Turn on the TV. Set the Brightness andContrast controls to minimum (zero beam cur-rent).

3. The high voltage should not exceed 27.5KV.

4. Adjust the Brightness and contrast controls toboth extremes. Ensure that the high voltagedoes not exceed 27.5KV under any conditions.

4-3-4 FOCUS Adjustment

1. Input a black and white signal.

2. Adjust the tuning control for the clearest pic-ture.

3. Adjust the FOCUS control for well definedscanning lines in the center area of the screen.

4-3-5 Cathode Voltage Adjustment(Screen Adjustment)

1. Connect CRT socket pin GK to an oscilloscopeprobe.

2. Input a gray scale pattern. (Use a pattern gen-erator, PM5518)

3. Use the P mode key (on the remote control)for the STANDARD picture.

4. Adjust the Screen VR (on the FBT) so that thevoltage on the oscilloscope becomes 130+2.5V(See Fig. 4-1).

4-3-6 Purity Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Plug in the CRT deflection yoke and tightenthe clamp screw.

3. Plug the convergence yoke into the CRT andset in as shown in Fig. 4-2.

4. Input a black and white signal.

5. Fully demagnetize the receiver by applying anexternal degaussing coil.

6. Turn the CONTRAST and BRIGHTNESS con-trols to maximum.

7. Loosen the clamp screw holding the yoke.Slide the yoke backward or forward to pro-vide vertical green belt. (Fig. 4-3).

8. Tighten the convergence yoke.

9. Slowly move the deflection yoke forward,and adjust for the best overall green screen.

10. Temporarily tighten the deflection yoke.

11. Produce blue and red rasters by a

Documents

samsung_cs3339z6x_cs3366z6x_cs5039z6x_chassis_s15a.pdf