Upload
lisette-marchant
View
218
Download
0
Embed Size (px)
Citation preview
8/12/2019 skyarm_i_e_ltr
1/9
Special Vehicle Series : 05
AssemblyInstructionsArticulated Ladder Truck
Canon Inc. Keisuke Saka+Kohei Masukawa
Tools Assembly tip
Key to symbols
Scissors
Ruler, set square
Glue (Wood glue or craft glue recommend)
Exhausted ballpoint pen (out of ink)
Toothpicks (for use in applying glue)
Tweezers (useful for handling small parts)
Pencil
Glue, scissors and other tools may be dangerous to young childrenso be sure to keep them out of the reach of young children.
Assembly Instructions: Nine US letter sheets (No. 1 to No. 9)Build this model with careful reference to the Assembly Instructions.
Write the number of each part on the reverse side of the part in pencil
upon cutting it out, to be sure you can tell which part is which later.
Before gluing, crease the paper along
mountain and valley fold lines. Trace along
the folds with a ruler and an exhausted
ballpoint pen (out of ink) to get a sharper fold.
Make sure rounded sections are nice and stiff.
Key to symbols
Pattern
Red dot
Green dot
Blue dot
Assembly instructions
Solid line
Dashed anddotted line
Dotted line
Solid blue line
Diagonalgrey lines
Mountain foldFold so that the printedpattern faces outside.
Fold so that the printedpattern faces inside.
Valley fold
Cut parts outalong this line.
Cut a notchalong this line.
Cut these areasout.
Glue parts with the samenumber together. (Numbers arenot printed on very small parts.)
Glue areas within the samepart together.
Glue
Insert
Glue tab
Reverse side ofpaper
(without gluing)
Red arrow
Blue arrow
Light blue
Light grey
Glue to the reverse side of thespecified part.
The dots show where to gluethe pieces together. Glue thepieces together as shown in thefollowing examples.Some parts must be gluedtogether along the cut surfaces.
This denotes a partthat must be able tomove after the modelis completed.Be sureto crease these partssufficiently.
Movable part
* This model was designed forPapercraft and may differ fromthe original in some respects.
View of completed model
8/12/2019 skyarm_i_e_ltr
2/9
Canon Inc. Keisuke Saka+Kohei MasukawaArticulated Ladder Truck
AssemblyInstructions
Assemble the cab.Glue flaps a, b, c, and d in order.
Do not fold these sections.
Do not fold these sections.
Attach parts 5 & 6 to part 4,
and parts 8 & 9 to part 7, and assemble.
After gluing parts 11 & 12 to the respectiveopenings, assemble by folding over left, right,and front sections.
8/12/2019 skyarm_i_e_ltr
3/9
Canon Inc. Keisuke Saka+Kohei MasukawaArticulated Ladder Truck
AssemblyInstructions
Assemble part 13, glue to ,and fold sections a, b, and c in order.
Glue flaps a, b, c, and d in order.
Glue the reversesurfaces together.
Insert part 18 through from the reverseof part 17 and glue in place.
Glue part 23 to the reverseof part 24 and assemble.
Glue the wings of part 27in place before assembling.
Glue a portionof part 26.
8/12/2019 skyarm_i_e_ltr
4/9
Canon Inc. Keisuke Saka+Kohei MasukawaArticulated Ladder Truck
AssemblyInstructions
Insert part 33 into part 34;do not glue.
Follow illustrations carefullywhen gluing the reverse side.
Side view
Glue reverse sidesof two forehand andinner units together.
This section is gluedin the next panel.
Insert part 40 into , sandwich between parts 31 and 32,then glue with part 39, confirming the width as you fix the parts in place.
Apply glue to fastener flap section of ,insert into part 38 and fix in place.
After gluing part 35 to part 41, insert into opening inand glue to part 36.
8/12/2019 skyarm_i_e_ltr
5/9
Canon Inc. Keisuke Saka+Kohei MasukawaArticulated Ladder Truck
AssemblyInstructions
Assemble parts and insert in order.Don't forget to cut the slit and holefor the telescopic stopper.
With the blue lines to rightand left, insert the stopperwith the hole facing down.
8/12/2019 skyarm_i_e_ltr
6/9
Canon Inc. Keisuke Saka+Kohei MasukawaArticulated Ladder Truck
AssemblyInstructions
Assemble part 50 with the patternedsurface to the inside,and insert into part 49.
Glue parts with no gluetabs to the areas cut outof the paper parts.
Reinforcement for moving parts;glue to inner surface.
Extend the moving telescopicsection and apply glue.
Glue flaps a and b in order.Insert part 47 and glueto base.
8/12/2019 skyarm_i_e_ltr
7/9
Canon Inc. Keisuke Saka+Kohei MasukawaArticulated Ladder Truck
AssemblyInstructions
Assemble front tires.
Attach the tires according to the diagram below.
Assemble outer rear tires. Assemble inner rear tires.
Front
Rear
8/12/2019 skyarm_i_e_ltr
8/9
Canon Inc. Keisuke Saka+Kohei MasukawaArticulated Ladder Truck
AssemblyInstructions
Align the holes and glue carefully,checking to ensure left and rightsides do not warp.
Glue to the underside.Don't forget to glueopposite piece too.
8/12/2019 skyarm_i_e_ltr
9/9
Canon Inc. Keisuke Saka+Kohei MasukawaArticulated Ladder Truck
AssemblyInstructions
ArticulatedLadderTruck
SpecialVehicleSeries
Finished!
Last, assemble the nameplate anddisplay it together with your model.
Insert the ladder assembly into
the hole but do not glue.The ladder should revolve freely.
Refer to the finished photoand attach small parts.