UNIVERSAL EDGE GUIDE

When using the EZ SMART Universal Edge Guide with any power tool, be sure you have read and understand the operating manual for the tool before operation. Be sure to use the tool safely. Do not disable any built-in safety features. Be sure to follow safe practices when using the EZ SMART Universal Edge Guide with your power tools. If a task seems like it might be potentially unsafe, do not attempt. Do not operate any tool with the EZ SMART Universal Edge Guide if you are tired or distracted in any way.

The EZ SMART Universal Edge Guide (UEG) turns your circular saw into a versatile cutting tool that can handle ripping procedures in a variety of materials, including dimensional lumber and large panels. The UEG can be used on vertical or horizontal workpieces. The EZ SMART Saw Base ensures safe, accurate, and chip-free cuts.

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (877) 681-7955 Fax (352) 620-2576 techsupport@eurekazone.com www.eurekazone.com

Parts

Frame(2) Arms with measurements(1) 24” Fence

Handle Assembly(1) Tubular handle(2) Black handle caps(2) T-nuts(2) 3/4” screws(2) Washers

Fence Hardware(2) Pre-tapped EZ Connectors(4) 5/8” screws(4) Washers(2) Locking hex nuts

Smart Base Assembly*(2) Studded EZ Connectors(4) Knobs(4) Washers(1) Smart Saw Base(1) Off-Rail Insert(2) On-Rail Inserts (Left and Right)(1) Fin Insert with (1) Fin * Smart Base Assembly is an optional component

v14-01Page 1

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (877) 681-7955 Fax (352) 620-2576 techsupport@eurekazone.com www.eurekazone.com

ASSEMBLING THE FRAME

Step 1

Insert a 5/8” screw into the third hole from end of the Arm. The washer is placed between the screw and the Arm. Repeat for the other Arm. Slide Fence over the connectors. Do not fully tighten the screws at this time.

Step 2

Line up the second hole in the Arm to the hole in the lip of the Fence. Insert screw and washer as shown at right. Repeat for the other Arm. Do not fully tighten the screws at this time.

Step 3

Square the Arm to the Fence and tighten the screws. Minor adjustments may be needed as the Handle and the Smart Saw Base are attached. The completed frame at this point is shown at the right.

v14-01Page 2

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (877) 681-7955 Fax (352) 620-2576 techsupport@eurekazone.com www.eurekazone.com

ATTACHING THE HANDLE

USING THE MARKS

Insert the T-nut through the hole in the Handle. Insert the screw with the washer through the first hole of the Arm, as shown, and into the end of the T-nut. Before fully tightening the screw, place the black end cap over the end of the Handle. Verify that the UEG frame is square, then tighten the screws.

The embossed marks on the EZ SMART Saw Base are used to line up the saw to the desired measurement on the UEG Arms. The embossed marks correspond to the inside edge of the saw blade.

FRONT EDGE OF SAW BASE BACK EDGE OF SAW BASE

Example:Cut set for 22”

ATTACHING THE SMART BASE

Slide studded EZ connectors into Arms. Place EZ SMART Saw Base on to studs as shown at right. Secure with washers and knobs.

Note: The Saw Base can be used to ensure that the UEG frame is square.

v14-01Page 3

Rip along the length of dimensional lumber or other long stock

Rip narrow strips from material

Rip irregular boards using a straight edge

Cut down large panels

Narrow Stock

Thin Strips Wide Boards

Straight-Line Rip

USING THE UEG

CAPACITY: 0-24” width of cut (markings for 0-24” on arms); unlimited workpiece length

● Keep Fence against the workpiece. Apply pressure using the Handle as the UEG is moved along the workpiece

● The long Fence can compensate for irregularities of the edge of the workpiece● The examples below show the workpiece laying in the horizontal position, but the UEG can also be used

with the workpiece in the vertical position.

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (877) 681-7955 Fax (352) 620-2576 techsupport@eurekazone.com www.eurekazone.com

Rip thin strips for larger stock

v14-01Page 4