UTC2000 Evaluation Kit User’s Guide - Microchip Technologyww1.microchip.com/downloads/en/DeviceDoc/50002399B.pdf · UTC2000 EVALUATION KIT USER’S GUIDE 2015 Microchip Technology

2015 Microchip Technology Inc. DS50002399B

UTC2000Evaluation Kit

User’s Guide

DS50002399B-page 2 2015 Microchip Technology Inc.

Information contained in this publication regarding device applications and the like is provided only for your convenience and may besuperseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NOREPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OROTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE,MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Micro-chip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and holdharmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly orotherwise, under any Microchip intellectual property rights unless otherwise stated.

Trademarks

The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

The Embedded Control Solutions Company and mTouch are registered trademarks of Microchip Technology Incorporated in the U.S.A.

Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet, KleerNet logo, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.

Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.

GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.

All other trademarks mentioned herein are property of their respective companies.

© 2015, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.

ISBN: 978-1-5224-0025-7

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of ourproducts. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such actsallow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified.

QUALITYMANAGEMENTSYSTEMCERTIFIEDBYDNV

== ISO/TS16949==

Object of Declaration: UTC2000

2015 Microchip Technology Inc. DS50002399B-page 3

UTC2000 Evaluation Kit User’s Guide

NOTES:


UTC2000EVALUATION KIT

USER’S GUIDE

Table of Contents

Preface ........................................................................................................................... 7Introduction............................................................................................................ 7

Document Layout EVK-UTC2000 ......................................................................... 7

Conventions Used in this Guide ............................................................................ 8

Warranty Registration............................................................................................ 9

The Microchip Website.......................................................................................... 9

Customer Support ................................................................................................. 9

Document Revision History ................................................................................. 10

Chapter 1. Overview1.1 UTC2000 Evaluation Kit Overview and Features ......................................... 111.2 Features ....................................................................................................... 111.3 General Description ...................................................................................... 121.4 References ................................................................................................... 131.5 Definition ...................................................................................................... 13

Chapter 2. Getting Started2.1 Contents of the Kit ........................................................................................ 152.2 Bring-Up and Testing ................................................................................... 15

2.2.1 Setup and Requirements ........................................................................... 152.2.2 EVB-UTC2000-DFP Legacy Charging Operation ..................................... 152.2.3 1.5A Charging Operation ........................................................................... 152.2.4 3.0A Charging Operation ........................................................................... 16

Chapter 3. Hardware Configuration3.1 Hardware Description ................................................................................... 17

3.1.1 Power Source ............................................................................................ 173.1.2 LED Indicators for EVB-UTC2000-DFP ..................................................... 183.1.3 Switches on EVB-UTC2000-DFP .............................................................. 193.1.4 Connector Descriptions for EVB-UTC2000-DFP ....................................... 203.1.5 Test Points on EVB-UTC2000-DFP .......................................................... 203.1.6 LED Indicators for EVB-UTC2000-UFP ..................................................... 203.1.7 Switches on EVB-UTC2000-UFP .............................................................. 213.1.8 Connector Descriptions for EVB-UTC2000-UFP ....................................... 213.1.9 Test Points on EVB-UTC2000-UFP .......................................................... 22

Appendix A. UTC2000 SchematicsA.1 Introduction .................................................................................................. 23

Appendix B. EVK-UTC2000 BOMB.1 Introduction .................................................................................................. 27

Appendix C. EVK-UTC2000 PCB Silk Screens



C.1 Introduction .................................................................................................. 31

Worldwide Sales and Service .....................................................................................34



USER’S GUIDE

Preface

INTRODUCTION

This chapter contains general information that will be useful to know before using the UTC2000 Evaluation Kit User’s Guide. Items discussed in this chapter include:

• Document Layout EVK-UTC2000

• Conventions Used in this Guide

• Warranty Registration

• The Microchip Website

• Customer Support

• Document Revision History

DOCUMENT LAYOUT EVK-UTC2000

This document describes how to use the UTC2000 Evaluation Kit as a demonstration platform optimized for portable applications. The manual layout is as follows:

• Chapter 1. “Overview” – Shows a brief description of the UTC2000 Evaluation Kit

• Chapter 2. “Getting Started” – Provides information about set-up and operation of the UTC2000 Evaluation Kit.

• Chapter 3. “Hardware Configuration” – Includes information about the hardware configuration of the UTC2000 Evaluation Kit.

• Appendix A. “UTC2000 Schematics”

• Appendix B. “EVK-UTC2000 BOM”

• Appendix C. “EVK-UTC2000 PCB Silk Screens”

NOTICE TO CUSTOMERS

All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so some actual dialogs and/or tool descriptions may differ from those in this document. Please refer to our website (www.microchip.com) to obtain the latest documentation available.

Documents are identified with a “DS” number. This number is located on the bottom of each page, in front of the page number. The numbering convention for the DS number is “DSXXXXXA”, where “XXXXX” is the document number and “A” is the revision level of the document.

For the most up-to-date information on development tools, see the MPLAB® IDE online help. Select the Help menu, and then Topics to open a list of available online help files.

Note: USB Type-C™ USB-C™ are trademarks of USB Implementation Forum.



CONVENTIONS USED IN THIS GUIDE

This manual uses the following documentation conventions:

DOCUMENTATION CONVENTIONS

Description Represents Examples

Arial font:

Italic characters Referenced books MPLAB® IDE User’s Guide

Emphasized text ...is the only compiler...

Initial caps A window the Output window

A dialog the Settings dialog

A menu selection select Enable Programmer

Quotes A field name in a window or dialog

“Save project before build”

Underlined, italic text with right angle bracket

A menu path File>Save

Bold characters A dialog button Click OK

A tab Click the Power tab

N‘Rnnnn A number in verilog format, where N is the total number of digits, R is the radix and n is a digit.

4‘b0010, 2‘hF1

Text in angle brackets < > A key on the keyboard Press <Enter>, <F1>

Courier New font:

Plain Courier New Sample source code #define START

Filenames autoexec.bat

File paths c:\mcc18\h

Keywords _asm, _endasm, static

Command-line options -Opa+, -Opa-

Bit values 0, 1

Constants 0xFF, ‘A’

Italic Courier New A variable argument file.o, where file can be any valid filename

Square brackets [ ] Optional arguments mcc18 [options] file [options]

Curly brackets and pipe character: |

Choice of mutually exclusive arguments; an OR selection

errorlevel 0|1

Ellipses... Replaces repeated text var_name [, var_name...]

Represents code supplied by user

void main (void) ...


Preface

WARRANTY REGISTRATION

Please complete the enclosed Warranty Registration Card and mail it promptly. Sending the Warranty Registration Card entitles users to receive new product updates. Interim software releases are available at the Microchip website.

THE MICROCHIP WEBSITE

Microchip provides online support via our website at www.microchip.com. This website is used as a means to make files and information easily available to customers. Acces-sible by using your favorite Internet browser, the website contains the following infor-mation:

• Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software

• General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip consultant program member listing

• Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives

CUSTOMER SUPPORT

Users of Microchip products can receive assistance through several channels:

• Distributor or Representative

• Local Sales Office

• Field Application Engineer (FAE)

• Technical Support

Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document.

Technical support is available through the website at: http://www.microchip.com/support


www.microchip.com

http://www.microchip.com/support

http://www.microchip.com/support


DOCUMENT REVISION HISTORY

Revision Section/Figure/Entry Correction

DS50002399A (07-30-15) Initial Release of Document

DS50002399B (11-20-15) Section 2.1 “Contents of the Kit”

Updated grammar.

Section 2.2.2 “EVB-UTC2000-DFP Legacy Charging

Operation”

Updated first paragraph to replace 56 k? with 56 kΩ.

Section 2.2.4 “3.0A Charging Operation”

Updated steps to reflect correct information.

Figure 3-3 Updated image to remove black square in middle of the diagram.

Figure 3-6 Added trademark symbol to USB Type-C™.

Figure 3-7 Replaced incorrect image.

Figure 3-8 Added trademark symbol to USB Type-C™.

Appendix A. “UTC2000 Schematics”

Updated all images to remove extraneous informa-tion.

Appendix B. “EVK-UTC2000 BOM”

Fixed inconsistent text size.



USER’S GUIDE

Chapter 1. Overview

1.1 UTC2000 EVALUATION KIT OVERVIEW AND FEATURES

The UTC2000 Evaluation Kit is intended to demonstrate the form factor and reversibil-ity of the USB Type-C™ cable operation as enabled by the UTC2000 basic Type-C controller. The kit includes a downstream facing port board, an upstream facing port board, and a USB Type-C cable, as shown in Figure 1-1. A basic USB Type-C connec-tion can be demonstrated with a standard USB 2.0 or USB 3.1* host port, the UTC2000 EVK and any USB 2.0 or USB 3.1 device. See Section 1.2 “Features” for more infor-mation.

1.2 FEATURES

• EVB-UTC2000-DFP converts any USB Type-A port to a USB Type-C port

• EVB-UTC2000-UFP converts any USB device to a USB Type-C device

• Compatible with USB 2.0 and USB 3.1 host ports and devices

• Supports basic USB Type-C 5V charging at:

- Legacy 500mA (USB 2.0)/900mA (USB 3.1)

- 1.5A

- 3.0A

• LED status indicators on the downstream facing port (DFP) board include:

- 5V board supply indicators

- “Overcurrent” and “Fault” indicators

- Plug orientation

Note: EVK-UTC2000 is enabled with a USB 3.1 Gen 1 switch. USB 3.1 Gen 2 can be supported by using a compliant USB 3.1 Gen 2 switch.

FIGURE 1-1: UTC2000 EVALUATION KIT



• LED status indicators on the upstream facing port (UFP) board include:

- 5 V board supply indicator

- Legacy, 1.5A, 3.0A charging detecting indicators

• DP3T switch on DFP board for legacy, 1.5A, 3.0A charging mode selection

• Reversible USB Type-C receptacle

• USB 3.1 passive Type-C Cable

1.3 GENERAL DESCRIPTION

FIGURE 1-2: EVB-UTC2000-DFP BLOCK DIAGRAM

UTC2000(DFP Mode)

USB Type-C

TMConnector

5V@4A Port Power Controller

VBUS

USB 3.1 Gen 1Switch

PLUG_ORIENTATION#

USB

PPC_EN

USB

USB

CC1

CC2

VCONN2_OUT#

VCONN1_OUT#5V

5V

RpRp

OCS#

USB 3.1 Gen 1Type-A Plug

ENABLE

5V

5V

VMON

5V 3.3V

5V to 3.3VRegulator

3.3V

VDD

5V

VDD

5V

VDD

VBUS

5V

0


Overview

1.4 REFERENCES

• USB Type-C™ Specification

• UTC2000 Data Sheet

• Introduction to USB Type-C™ Application Note(http://ww1.microchip.com/downloads/en/AppNotes/00001953A.pdf)

• Basic USB Type-C™ Upstream Facing Port Implementation(http://ww1.microchip.com/downloads/jp/AppNotes/jp574170.pdf)

1.5 DEFINITION

• DFP - Downstream Facing Port

• EVB - Evaluation Board

• EVK - Evaluation Kit

• UFP - Upstream Facing Port

FIGURE 1-3: EVB-UTC2000-UFP BLOCK DIAGRAM

UTC2000(UFP Mode)

USB 3.1 Gen 1Switch

USB

USB

CC1

CC2

RpRp

USB

CONNECTED#

VBUS VBUS

LEGACY_IND#

1.5A_IND#

3.0A_IND#

VMON

PLUG_ORIENTATION#

Type‐A Receptacle

5V 3.3V

5V to 3.3VRegulator

5V

VDD

3.3V

VDD


http://ww1.microchip.com/downloads/en/AppNotes/00001953A.pdf

http://ww1.microchip.com/downloads/jp/AppNotes/jp574170.pdf


NOTES:



Chapter 2. Getting Started

2.1 CONTENTS OF THE KIT

The UTC2000 Evaluation kit includes the basic equipment necessary for evaluation. The items included in the kit are:

1. EVB-UTC2000-DFP Evaluation Board

2. EVB-UTC2000-UFP Evaluation Board

3. USB Type-C Cable

2.2 BRING-UP AND TESTING

2.2.1 Setup and Requirements

• EVB-UTC2000-DFP: Before use, slide SW1 to the legacy charging mode. To use, simply insert the device into any USB Type-A USB 2.0 or USB 3.1 host port. Any USB Type-C device may now be connected to the USB Type-C port. The revers-ibility of the USB Type-C cable can be demonstrated by connecting it in the oppo-site direction.

• EVB-UTC2000-UFP: To use, connect to any USB Type-C host or hub port. If there is no native USB Type-C host available, the EVB-UTC2000-DFP board may be used. Insert a USB 2.0 or USB 3.1 device into the Type-A receptacle (J2) of the EVB-UTC2000-UFP. The device may then be used normally.

2.2.2 EVB-UTC2000-DFP Legacy Charging Operation

The EVB-UTC2000-DFP board is configured to Legacy 500mA (USB2.0)/900mA (USB3.1 Gen1) charging mode by default. Ensure that SW1 is in the “Lgcy” position. The switch will select 56 kΩ CC1/CC2 Rp pull-up resistors and set the CFG_SEL volt-age to the appropriate level.

When connecting the EVB-UTC2000-DFP board to the EVB-UTC2000-UFP while in Legacy charging mode, the “Legacy” charging capability LED indicator (D4) on the EVB-UTC2000-UFP will be illuminated.

2.2.3 1.5A Charging Operation

The EVB-UTC2000-DFP is designed to plug in and operate from any legacy USB Type-A port. To protect your computer from possible overcurrent issues, 1.5A and 3.0A modes have been disabled by default.

To test 1.5A charging mode, perform the following steps:

1. Remove R15 and R17 56k Rp pull-up resistors.

2. Populate R18 and R23 with 22k, 0402 footprint resistors.

3. Set SW1 to the “1.5A” position.

4. Remove R3 to isolate the 5V domain on the EVB-UTC200-DFP from the 5V domain on your host PC.

5. Connect an external power supply as shown in Section 3.1.1 “Power Source”.



When connecting the EVB-UTC2000-DFP board to the EVB-UTC2000-UFP while in 1.5A charging mode, the “1.5A” charging capability LED (D3) indicator on the EVB-UTC2000-UFP will be illuminated.

2.2.4 3.0A Charging Operation

The EVB-UTC2000-DFP is designed to plug in and operate from any legacy USB Type-A port. To protect your computer from possible overcurrent issues, 1.5A and 3.0A modes have been disabled by default.

To test 3.0A charging mode, perform the following steps:

1. Remove R15 and R17 56k Rp pull-up resistors.

2. Populate R24 and R27 with 10k, 0402 footprint resistors.

3. Set SW1 to the “3.0A” position.

4. Remove R3 to isolate the 5V domain on the EVB-UTC200-DFP from the 5V domain on your host PC.

5. Connect an external power supply as shown in Section 3.1.1 “Power Source”.

When connecting the EVB-UTC2000-DFP board to the EVB-UTC2000-UFP while in 3.0A charging mode, the “3.0A” charging capability LED indicator (D2) on the EVB-UTC2000-UFP will be illuminated.



USER’S GUIDE

Chapter 3. Hardware Configuration

3.1 HARDWARE DESCRIPTION

3.1.1 Power Source

The EVB-UTC2000-DFP can be powered in one of two ways:

1. Host/Hub Port VBUS: The board can be powered by 5V VBUS sourced from the connected host port. Do not operate with SW1 in the 1.5A or 3.0A modes and attempt to draw 1.5A or 3.0A when connected in this way, as Legacy USB Type-A host ports typically cannot support this amount of current draw.

2. External 5V Supply: An external 5V supply may be connected to TP1 to test 1.5A and 3.0A charging. Be sure to remove the R3 zero-ohm resistor to prevent voltage back drive to the host/hub port, as shown in Figure 3-3.

FIGURE 3-1: EVB-UTC2000-UFP (TOP-SIDE)

FIGURE 3-2: EVB-UTC2000-DFP (TOP-SIDE)



The EVB-UTC2000-UFP is always powered from VBUS supplied by the downstream facing port it is attached to.

3.1.2 LED Indicators for EVB-UTC2000-DFP

Table 3-1 describes the LED indicators included on the EVB-UTC2000-DFP.

FIGURE 3-3: EVB-UTC2000-DFP EXTERNAL 5V SUPPLY

EVB-UTC2000-DFP

Type-APlug TP2

GND

TP1

EXT5VR3

Type-CReceptacle

HostPort

Type-CDevice

Bench Voltage Supply

V+ V-

EVB UTC2000 DFP

TP2

GNDNDNDNDDNDNNDND

TP1

EXT5V5V

V+R3 Removed

TABLE 3-1: LED INDICATOR DESCRIPTIONS

REF.DES.

LABEL DESCRIPTION

D2 “VBUS IN” Indicates that 5V board power is present.

D3 “VBUS ON” Indicates 5V is being supplied to VBUS on the Type-C port.

D4 “FAULT” Indicates an overvoltage or overcurrent event has occurred. This indicator will reset with a power cycle of the board.

D5 “OVRCUR” Indicates an overcurrent event is occurring. This signal is driven by the 5V port power controller.

D6 “PLUG ORIENT” Indicates the state of the PLUG_ORIENTATION# signal. When illu-minated, PLUG_ORIENTATION is being driven low by the UTC2000.


Hardware Configuration

Figure 3-4 shows their location on the PCB.

3.1.3 Switches on EVB-UTC2000-DFP

Table 3-2 describes the switches included on the EVB-UTC2000-DFP.


FIGURE 3-4: EVB-UTC2000-DFP LED INDICATOR LOCATIONS

VBUS ONVBUS IN

Fault Indicator

Over-currentIndicator

Plug OrientationIndicator

TABLE 3-2: SWITCH DESCRIPTIONS

REF. DES. LABEL DESCRIPTION

SW1 “Lgcy -- 1.5A -- 3A”

Selects between the DFP modes of operation: “Lgcy”, “1.5A”, “3.0A”

Note: The EVB-UTC2000-DFP is configured for Legacy mode of operation by default. See Section 2.2.3 “1.5A Charging Operation”/Section 2.2.4 “3.0A Charging Operation” for information on testing 1.5A/3.0A modes respectively.

FIGURE 3-5: EVB-UTC2000-DFP SWITCH LOCATIONS

SW1



3.1.4 Connector Descriptions for EVB-UTC2000-DFP

Table 3-3 describes the connectors included on the EVB-UTC2000-DFP.

3.1.5 Test Points on EVB-UTC2000-DFP

Table 3-4 describes the test points included on the EVB-UTC2000-DFP. A header may be permanently installed on the through-hole test points if needed.

3.1.6 LED Indicators for EVB-UTC2000-UFP

Table 3-5 describes the LED indicators included on the EVB-UTC2000-UFP.

TABLE 3-3: CONNECTOR DESCRIPTIONS

REF. DES. TYPE LABEL DESCRIPTION

J1 1x5 Header - 5-pin debug header (internal MCHP use only)

J2 USB 3.1 Type-A Plug

- Type-A male plug

J3 USB 3.1 Type-C

Receptacle

- Type-C receptacle

FIGURE 3-6: EVB-UTC2000-DFP CONNECTOR LOCATIONS

USB Type-A PlugUSB Type-A Plug

USBType-C™

USBType-C™

1x5 Debug Header1x5 Debug Header

TABLE 3-4: EVB-UTC2000-DFP TEST POINT DESCRIPTIONS

REF. DES. TYPE DESCRIPTION

TP1 Thru-Hole 5V probe point or external 5V supply point

TP2 Thru-Hole GND

TABLE 3-5: EVB-UTC2000-UFP LED INDICATOR DESCRIPTIONS

REF.DES.

LABEL DESCRIPTION

D1 “VBUS IN” Indicates that a valid VBUS (5.5V-4.0V) is being supplied to the EVB-UTC2000-UFP from the USB Type-C™ connection and that 5V is being passed to the USB Type-A receptacle.

D2 “3A” Indicates when a 3.0 A capable DFP connection is detected.

D3 “1.5A” Indicates when a 1.5 A capable DFP connection is detected.

D4 “Legacy” Indicates when legacy 500 mA (USB 2.0)/900 mA (USB 3.1) capa-ble DFP connection is detected.


Hardware Configuration


3.1.7 Switches on EVB-UTC2000-UFP

There are no switches present on the EVB-UTC2000-UFP.

3.1.8 Connector Descriptions for EVB-UTC2000-UFP

Table 3-6 describes the connectors included on the EVB-UTC2000-UFP.

FIGURE 3-7: EVB-UTC2000-UFP LED INDICATOR LOCATIONS

Legacy

VBUS IN

1.5A

3.0A

TABLE 3-6: EVB-UTC2000-UFP CONNECTOR DESCRIPTIONS

REF. DES. TYPE LABEL DESCRIPTION

J1 1x5 Header - 5-pin debug header (internal Microchip use only)

J2 USB 3.1 Type-A Plug

- USB Type-A receptacle

J3 USB 3.1 Type-C

Receptacle

- USB Type-C™ receptacle

J4 Load Loop - An external load may be connected between this load loop and GND (pin 3 of J1)



3.1.9 Test Points on EVB-UTC2000-UFP

There are no test points available on the EVB-UTC2000-UFP.

FIGURE 3-8: EVB-UTC2000-UFP CONNECTOR LOCATIONS

USBType‐C™USB

Type‐C™

USBType‐A

Receptacle

USBType‐A

Receptacle

1x5 Debug Header1x5 Debug Header

External Load LoopExternal Load Loop



USER’S GUIDE

Appendix A. UTC2000 Schematics

A.1 INTRODUCTION

This appendix shows the UTC2000 Evaluation Kit Schematic.


UT

C2000 E

valuatio

n K

it User’s G

uid

e

DS

50002399B

-page 24

2015 M

icrochip Technolo

gy Inc.

CC2CC1

D_ND_P

RXM_A_NRXM_A_P

TXM_A_NTXM_A_P

RXM_B_NRXM_B_P

TXM_B_NTXM_B_P

BUS_C

330RR12

"

0.1uF16V0402

C12

pped

GNDA1

TX1+A2TX1-A3

VBUSA4

CC1A5

D+A6D-A7

RFU1A8

VBUSA9

RX2-A10

RX2+A11

GNDA12GNDB1

TX2+B2

TX2-B3

VBUSB4

CC2B5

D+B6D-B7

RFU2B8

VBUSB9

RX1-B10 RX1+B11

GNDB12 SHLD

0

J3

USB

Typ

e-C_A

CON_H

ybrid

F

FIGURE A-1: UTC2000 EVALUATION KIT SCHEMATICS

A Plug

C Connector

PLUG_ORIENTATION#3.3V

RXM_A_NRXM_A_P

TXM_A_NTXM_A_P

RXM_B_NRXM_B_P

TXM_B_NTXM_B_P

V

5V PPC

VBUS_C

PPC_EN

OCS#

3.3V

"VBUS In"

VBUS 1

SSRX- 5

D- 2D+ 3

VBUS

SSRX-

D-D+

Shield

0

SSRX+ 6

GND_D 7SSTX- 8

SSTX+ 9

GND 4

USB 3.0 A PLUGJ2

330R

R13

D_ND_P

RXM_NRXM_P

TXM_NTXM_P

SS Mux

"VBUS Out

TP LOOP Red

DNPTP1

TP LOOP Black

DNPTP2

[Pos 1] VBUS Pass Thru[Pos 2] External 5V

5V Source Selector5Vin

5Vin

5V

1k0402

R2

1k0402

R4

100k04021%

R22

0.1uF16V0402

C9

0.1uF16V0402

C80.1uF16V0402

C6

0.1uF16V0402

C10

10uF6.3V0603

DNP

C7

MAX1563ETC+

FAULT 5

OUT 10OUT 1

IN9

IN12

SEL3

NC8 NC2

NC11

ON4

GND

6

ISET7

EP13

U3

MAX1563ETC+

35.7K04021%

R1

VMON

5V

0.1uF16V0402

C2

1%5.1kR6

1%5.1kR5

4.7uF10V0603

C11

ISET is configured for >3.35A Overcurrent

D+6

VDD3

VDD12

HS_SEL32

OE11

GNDFLAG33

D-7

TX-2

VDD16

VDD9

D+B 15

RX+4

SS_SEL10 D-B 14

USB-IDA 17

D+A 19

GND21

USB_ID8

USB_IDB 13

D-A 18

VDD20

TX-A 30

RX-5

TX+A 31

GND28

VDD29

RX-A 26RX+A 27

TX+B 25TX-B 24

RX-B 22

RX+B 23

TX+1

PI3USB3102ZLE

U4

**Note: CC1/CC2 intentionally swato facilitate cleaner USB3.0signal routing

1.0μF

C13

Br Grn

D2

Br GrnD3

**Note: Route CC traces50Ohm Single-Ended

1

23

BAV99

D1

0R0805

R3

+/- are intentionally

47μ16V

C1

swapped forsimplified routing

UT

C2000 S

chem

atics

2015

Microchip T

echnology Inc.D

S5

0002399B-p

age 25

FIG

5V

ug Header

ENABLE

(Internal Use Only)

MCP1755T-3302E/OT

SHDN3

VOUT 5

GND

2

VIN1

PWRGD 4

U13.3V

0.1uF16V

C31.0μF

C4

VMONPLUG_ORIENTATION#

URE A-1: UTC2000 EVALUATION KIT SCHEMATICS (CONTINUED)

UTC2000

CC1CC2

5V 12

34

5

DNP

J1

Deb

ENABLE

VCONN1#VCONN2#

CC2

CC1

Debug Header

5V 5VCC Pins

PPC_EN

OCS#

"OverCurrent"

Current Capability Marker SelectorPos 1 - Legacy USB (900mA)Pos 2 - 1.5A CapablePos 3 - 3.0A Capable

YELLOWD6

"Plug Orientation"

5V

5V

3.3V

3.3V Supply

5V

CFG_SEL

PLUG_ORIENTATION#

"Fault"

1k04021%

R11

1k0402R10

1k0402

R9

100k0402

R7100k0402

R8

0.1uF16V0402

C14

1

2

C1

C1

3

4

5

C2

C2

6

SW1

AYZ0203AGRLC

10k04021%

DNPR27

10k04021%

DNPR24

10k0402

R14

1.0μF

C5

22k04021%

DNPR23

22k04021%

DNPR1856k

04021%

R1756k04021%

R15

CFG_SEL

56k04021%

R21

CFG_SEL = 1.25V : 3.0A ModeCFG_SEL = 0.75V : 1.5A Mode

Configuration Selection

10k04021%

R28

1%040230kR25

5V

CFG_SEL = 0.00V : Legacy 500mA/900mA Mode

VMON

3

5

4

PMDXB600UNEQ5B

PMDXB600UNE6

2

1

Q5A

5V

1.5A_SEL

3A_SEL

1.5A_SEL 3A_SEL

100k04021%

R29100k04021%

R19

PMDXB600U

NE6

2

1 Q6A

3

5

4

PMDXB600U

NE

Q6B

5V CC1 7

VDD16

VSS13EPAD17 CC2 6

VCONN1_OUT#/1.5A_IND# 9

VCONN2_OUT#/LEGACY_IND# 8

OCS# 1

AUDIO_ADPT/CONNECTED# 5

FAULT_IND 4

CFG_SEL2

ENABLE3

PLUG_ORIENTATION# 11

PPC_EN/3.0A_IND# 10

VMON 12

NC15NC14

U2

UTC2000PLUG_ORIENTATION# indicates the Type-C cable.insertion orientation.

HIGH = not connected or connected or unflippedi.e.: CC >> CC1

LOW = connected and flippedi.e.: CC >> CC2

Br RedD5

Br Red

D4

10k0402

R30

3.3V

5V

100k04021%

R26PMDXB600U

NE6

2

1 Q4A

3

5

4

PMDXB600U

NE

Q4B

100k04021%

R20

PMDXB600U

NE6

2

1 Q3A

3

5

4

PMDXB600U

NE

Q3B

100k04021%

R16

CC2

CC1

VCONN1#VCONN2#

4

5

3

Q2ACMLDM8005

1

2

6

Q2BCMLDM8005

4

5

3

Q1ACMLDM8005

1

2

6

Q1BCMLDM8005

PLUG_ORIENTATION#

R18/R23, R24/R27 are not populated by default because

In order to test higher current modes, ensure to do the following:this EVB is designed to plug into any legacy USB port.

1. Remove R15 and R172. Populate R18/R23 for 1.5A mode, or R24/R27 for 3.0A3. Set SW1 in the corresponding position4. Remove R3 to isolate 5V from the host PC5. Connect an external high currect bench supply to TP1/TP2

> 5.5V is recommended if testing 3A mode

UT

C2000 E

valuatio

n K

it User’s G

uid

e

DS

50002399B

-page 26

2015 M

icrochip Technolo

gy Inc.

Reg

BLUED4

"Legacy"

"1.5A"

"3.0A"

BLUED3

BLUED2

1k0402

R7

1k0402

R3

1k0402

R1

LEGACY_IND#

1.5A_IND#

3.0A_IND#

5V

1uF10V0402

C51uF10V0402

C7

MCP1755T-3302E/OT

SHDN3

VOUT 5

GND

2

VIN1

PWRGD 4

U1 3.3V

5V

5V

0.1uFC6

0.1uFC8

FIGURE A-1: UTC2000 EVALUATION KIT SCHEMATICS (CONTINUED)

SS MuxC Connector

RXM_A_NRXM_A_P

TXM_A_NTXM_A_P

RXM_B_NRXM_B_P

TXM_B_P

RXM_A_NRXM_A_P

TXM_A_NTXM_A_P

RXM_B_NRXM_B_P

TXM_B_NTXM_B_P

330RR16

"VBUS In"

330R

R15

VBUS1

SSRX-5

D-2D+3VBUS

SSRX-

D-D+

Shield

0

SSRX+6

GND_D7SSTX-8

SSTX+9

GND4

USB 3.0 A RCPTJ2

0RDNPR14

5V_OUT

A Receptacle

CC1CC2

3.3V

**Note: Route CC traces50Ohm Single-Ended

0.1uF10V0402

C30.1uF10V0402

C4

0.1uF10V

C9

1k0402

R2

D_ND_P

RXM_NRXM_P

TXM_NTXM_P

TXM_B_N

D_ND_P

UTC20005V

ENABLE

PLUG_ORIENTATION#

LEGACY_IND#1.5A_IND#

YELLOWD6

"Plug Orientation"

3.3V

CFG_SEL

"Fault"

1k0402

R131k

0402R12

10k0402

R6

CC1 7

VDD16

VSS13

EPAD17 CC2 6

VCONN1_OUT#/1.5A_IND# 9

VCONN2_OUT#/LEGACY_IND# 8

OCS# 1

AUDIO_ADPT/CONNECTED# 5

FAULT_IND 4

CFG_SEL2

ENABLE3

PLUG_ORIENTATION# 11

PPC_EN/3.0A_IND# 10

VMON 12

NC15

NC14

U2

UTC2000

5V

3.3V

3.0A_IND#

12

34

5

DNP

J1

5V

Debug Header

ENABLE

PLUG_ORIENTATION#

VMON

VMON

35.7K04021%

R4

1

23

BAV99

D7

5V

5V

VMON

5V

CFG_SEL = VDDProfile: UFP

BSO080P03NS3E G

41,2

,3

5,6,7,8Q1

CONNECTED#

CONNECTED#100k

0603R17

PLUG_ORIENTATION#

1%5.1kR5

1%5.1kR10

1%5.1kR11

PI3USB3102ZLE

D+ 6

VDD 3

VDD 12

HS_SEL 32

OE 11

GNDFLAG 33

D- 7

TX- 2

VDD 16

VDD 9

D+B15

RX+ 4

SS_SEL 10D-B14

USB-IDA17

D+A19

GND 21

USB_ID 8

USB_IDB13

D-A18

VDD 20

TX-A30

RX- 5

TX+A31

GND 28

VDD 29

RX-A26

RX+A27

TX+B25 TX-B24

RX-B22RX+B23

TX+ 1

U3

PI3USB3102

PLUG_ORIENTATION# indicates the Type-C cable.insertion orientation.

HIGH = not connected or connected or unflippedi.e.: CC >> CC1

LOW = connected and flippedi.e.: CC >> CC2

**Note: CC1/CC2 intentionally swappedto facilitate cleaner USB3.0signal routing

Br Grn

D1

Br Red

D5

0.1uF10V0402

C1

10k0402

R18

3.3V

GND A1

TX1+ A2

TX1- A3

VBUS A4

CC1 A5

D+ A6

D- A7

RFU1 A8

VBUS A9

RX2- A10RX2+ A11

GND A12

GND B1

TX2+ B2

TX2- B3

VBUS B4

CC2 B5

D+ B6

D- B7

RFU2 B8

VBUS B9

RX1- B10RX1+ B11

GND B12SHLD

0

J3

USB

Typ

e-C_A

CON_H

ybrid

1

TP LOOP Tin

J4

10kR19

10kR20

CC1

CC2

0.1uF

C11

0.1uF

C12

0.1uFC10

0.1uFC2

0R0402

DNP R9

1k0603

R8


USER’S GUIDE

Appendix B. EVK-UTC2000 BOM

B.1 INTRODUCTION

This appendix shows the EVK-UTC2000 Evaluation Bill of Materials.


UT

C2000 E

valuatio

n K

it User’s G

uid

e

DS

50002399B

-page 28

2015 M

icrochip Technolo

gy Inc.

turerManufacturerPart Number

oration C3216X5R1C476M160AB

o CC0402ZRY5V7BB104

oration C1005X5R1C105K050BC

06036D106MAT2A

uden LMK107BJ475KA-T

ild BAV99

n LTST-C191KGKT

n LTST-C191KRKT

M LY Q976-P1S2-36

ec TSW-105-07-S-S

ronics Inc 692112030100

N

iconductor CMLDM8005 TR

nductors PMDXB600UNE

onic ERJ-2RKF3572X

onic ERJ-2RKF1001X

onic ERJ-6GEY0R00V

onic ERJ-2RKF5101X

onic ERJ-2RKF1003X

M MCR03EZPFX3300

onic ERJ-2RKF1002X

M MCR01MZPF5602

onic ERJ-2RKF3002X

ponents AYZ0203AGRLC

TABLE B-1: EVK-UTC2000-DFP BILL OF MATERIALS

Item QtyQty

Pop'dReference

Designator(s)Description Manufac

1 1 1 C1 CAP CER, 47uF, 16V, 20%, X5R, 1206 TDK Corp

2 8 8 C2, C3, C6, C8, C9, C10, C12,

C14

CAP CER, 0.1uF, 16V, 80%, SMD, 0402 Yage

3 3 3 C4, C5, C13 CAP CER, 1uF, 16V, 10%, X5R, 0402 TDK Corp

4 1 1 C7 CAP CER, 10uF, 6.3V, 20%, X5R SMD, 0603 AVX

5 1 1 C11 CAP CER, 4.7uF, 10V, 10%, X5R SMD, 0603 Taiyo Y

6 1 1 D1 DIO RECTARR, BAV99, 1.25V, 200mA, 70V, SOT-23-3 Fairch

7 2 2 D2, D3 LED, Bright Green, 0603 Lite-O

8 2 2 D4, D5 LED, Bright Red, 0603 Lite-O

9 1 1 D6 DIO LED YELLOW 2V 25mA 162.5mcd Diffuse SMD 0603 OSRA

10 1 1 J1 CON HDR-2.54 Male 1x5 Gold 5.84MH TH VERT Samt

11 1 1 J2 CON USB 3.1 Gen 1 STD-A PLUG SMD R/A Wurth Elect

12 1 1 J3 CON USB 3.1 Gen 1 Hybrid Type-C ACO

13 2 2 Q1, Q2 MOSFET SMD- Small Signal P-Channel Mosfet Central Sem

14 4 4 Q3, Q4, Q5, Q6 MOSFET TRENCH 2N-CH 20V 600MA SOT-1216 NXP Semico

15 1 1 R1 RES SMD 35.7K OHM 1% 1/10W 0402 Panas

16 5 5 R2, R4, R9, R10, R11

RES TKF 1k 1% 1/10W SMD 0402 Panas

17 1 1 R3 RES TKF 0R 1/8W SMD 0805 Panas

18 2 2 R5, R6 RES SMD 5.1K OHM 1% 1/10W 0402 Panas

19 8 8 R7, R8, R16, R19, R20, R22,

R26, R29

RES TKF 100k 1% 1/10W SMD 0402 Panas

20 2 2 R12, R13 RES TKF 330R 1% 1/10W SMD 0603 ROH

21 3 3 R14, R28, R30 RES TKF 10k 1% 1/10W SMD 0402 Panas

22 3 3 R15, R17, R21 RES TKF 56k 1% 1/16W SMD 0402 ROH

23 1 1 R25 RES SMD 30K OHM 1% 1/10W 0402 Panas

24 1 1 SW1 SW SLIDE DP3T 12VDC 100MA SMT C&K Com

EV

K-U

TC

2000 BO

M

2015

Microchip T

echnology Inc.D

S5

0002399B-p

age 29

2 5000

2 5001

2 logy MCP1755T-3302E/OT

2 logy UTC2000/MG

2 ted MAX1563ETC+

3 PI3USB3102ZLE

TA

It rManufacturerPart Number

C0402C104K8PACTU

s North GRM155R61A105KE15D

LTST-C191KGKT

LTST-C193TBKT-5A

LTST-C191KRKT

LY Q976-P1S2-36

BAV99

TSW-105-07-S-S

s Inc 692121030100

1

1 S1751-46R

1 ogies BSO080P03NS3E G

1 ERJ-2RKF1001X

1 ERJ-2RKF3572X

1 ERJ-2RKF5101X

1 ERJ-2RKF1002X

1 RC0603FR-071KL

TA

It rManufacturerPart Number

5 1 1 TP1 MISC, TEST POINT MULTI PURPOSE MINI RED Keystone

6 1 1 TP2 MISC, TEST POINT MULTI PURPOSE MINI BLACK Keystone

7 1 1 U1 IC REG LDO 3.3V 0.3A SOT23-5 Microchip Techno

8 1 1 U2 UTC2000 TYPEC CONTROLLER 16QFN Microchip Techno

9 1 1 U3 IC CURR-LIM SW SNGL PROG 12-TQFN Maxim Integra

0 1 1 U4 IC USB 3.1 Gen 1 & USB 2.0 SWITCH 32TQFN Pericom

BLE B-2: EVK-UTC2000-UFP BILL OF MATERIALS

em QtyQty

Pop'dReference

Designator(s)Description Manufacture

1 8 8 C1, C2, C3, C4, C6, C8, C9, C10

CAP CER 0.1uF 10V 10% X5R SMD 0402 KEMET

2 2 2 C5, C7 CAP CER 1uF 10V 10% X5R 0402 Murata ElectronicAmerica

3 1 1 D1 LED, Bright Green, 0603 Lite-On

4 3 3 D2, D3, D4 DIO LED BLUE 2.8V 20mA 15mcd Clear SMD 0603 Lite-On

5 1 1 D5 LED, Bright Red, 0603 Lite-On

6 1 1 D6 DIO LED YELLOW 2V 25mA 162.5mcd Diffuse SMD 0603 OSRAM

7 1 1 D7 DIO RECTARR BAV99 1.25V 200mA 70V SOT-23-3 Fairchild

8 1 1 J1 CON HDR-2.54 Male 1x5 Gold 5.84MH TH VERT Samtec

9 1 1 J2 CON USB 3.1 Gen 1 STD-A RCPT TH R/A Wurth Electronic

0 1 1 J3 CON USB 3.1 Gen 1 Hybrid Type-C ACON

1 1 1 J4 CON TP LOOP Tin SMD Harwin Inc

2 1 1 Q1 MOSFET P-CH 30V 12A 8DSO Infineon Technol

3 6 6 R1, R2, R3, R7, R12, R13

RES TKF 1k 1% 1/10W SMD 0402 Panasonic

4 1 1 R4 RES SMD 35.7K OHM 1% 1/10W 0402 Panasonic

5 3 3 R5, R10, R11 RES SMD 5.1K OHM 1% 1/10W 0402 Panasonic

6 2 2 R6, R18 RES TKF 10k 1% 1/10W SMD 0402 Panasonic

7 1 1 R8 RES TKF 1k 1% 1/10W SMD 0603 Yageo

BLE B-1: EVK-UTC2000-DFP BILL OF MATERIALS (CONTINUED)

em QtyQty

Pop'dReference

Designator(s)Description Manufacture

UT

C2000 E

valuatio

n K

it User’s G

uid

e

DS

50002399B

-page 30

2015 M

icrochip Technolo

gy Inc.

ay CRCW12100000Z0EA

M MCR03EZPFX3300

onic ERJ-3EKF1003V

echnology MCP1755T-3302E/OT

chnology EVK-UTC2000-UFP

om PI3USB3102ZLE

cturerManufacturerPart Number

18 1 1 R14 RES TKF 0R 1/3W SMD 1210 Vish

19 2 2 R15, R16 RES TKF 330R 1% 1/10W SMD 0603 ROH

20 1 1 R17 RES TKF 100k 1% 1/10W SMD 0603 Panas

21 1 1 U1 IC REG LDO 3.3V 0.3A SOT23-5 Microchip T

22 1 1 U2 UTC2000 TYPEC CONTROLLER 16QFN Microchip Te

23 1 1 U3 IC USB 3.1 Gen 1 & USB 2.0 SWITCH 32TQFN Peric

TABLE B-2: EVK-UTC2000-UFP BILL OF MATERIALS (CONTINUED)

Item QtyQty

Pop'dReference

Designator(s)Description Manufa


USER’S GUIDE

Appendix C. EVK-UTC2000 PCB Silk Screens

C.1 INTRODUCTION

This appendix shows the EVK-UTC2000 Top and Bottom Silk Screen Images.

FIGURE C-1: EVB-UTC2000-DFP TOP AND BOTTOM SILK SCREEN IMAGES



FIGURE C-2: EVB-UTC2000-UFP TOP AND BOTTOM SILK SCREEN IMAGES


EVK-UTC2000 PCB Silk Screens

NOTES:



AMERICASCorporate Office2355 West Chandler Blvd.Chandler, AZ 85224-6199Tel: 480-792-7200 Fax: 480-792-7277Technical Support: http://www.microchip.com/supportWeb Address: www.microchip.com

AtlantaDuluth, GA Tel: 678-957-9614 Fax: 678-957-1455

Austin, TXTel: 512-257-3370

BostonWestborough, MA Tel: 774-760-0087 Fax: 774-760-0088

ChicagoItasca, IL Tel: 630-285-0071 Fax: 630-285-0075

ClevelandIndependence, OH Tel: 216-447-0464 Fax: 216-447-0643

DallasAddison, TX Tel: 972-818-7423 Fax: 972-818-2924

DetroitNovi, MI Tel: 248-848-4000

Houston, TX Tel: 281-894-5983

IndianapolisNoblesville, IN Tel: 317-773-8323Fax: 317-773-5453

Los AngelesMission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608

New York, NY Tel: 631-435-6000

San Jose, CA Tel: 408-735-9110

Canada - TorontoTel: 905-673-0699 Fax: 905-673-6509

ASIA/PACIFICAsia Pacific OfficeSuites 3707-14, 37th FloorTower 6, The GatewayHarbour City, Kowloon

Hong KongTel: 852-2943-5100Fax: 852-2401-3431

Australia - SydneyTel: 61-2-9868-6733Fax: 61-2-9868-6755

China - BeijingTel: 86-10-8569-7000 Fax: 86-10-8528-2104

China - ChengduTel: 86-28-8665-5511Fax: 86-28-8665-7889

China - ChongqingTel: 86-23-8980-9588Fax: 86-23-8980-9500

China - DongguanTel: 86-769-8702-9880

China - HangzhouTel: 86-571-8792-8115 Fax: 86-571-8792-8116

China - Hong Kong SARTel: 852-2943-5100 Fax: 852-2401-3431

China - NanjingTel: 86-25-8473-2460Fax: 86-25-8473-2470

China - QingdaoTel: 86-532-8502-7355Fax: 86-532-8502-7205

China - ShanghaiTel: 86-21-5407-5533 Fax: 86-21-5407-5066

China - ShenyangTel: 86-24-2334-2829Fax: 86-24-2334-2393

China - ShenzhenTel: 86-755-8864-2200 Fax: 86-755-8203-1760

China - WuhanTel: 86-27-5980-5300Fax: 86-27-5980-5118

China - XianTel: 86-29-8833-7252Fax: 86-29-8833-7256

ASIA/PACIFICChina - XiamenTel: 86-592-2388138 Fax: 86-592-2388130

China - ZhuhaiTel: 86-756-3210040 Fax: 86-756-3210049

India - BangaloreTel: 91-80-3090-4444 Fax: 91-80-3090-4123

India - New DelhiTel: 91-11-4160-8631Fax: 91-11-4160-8632

India - PuneTel: 91-20-3019-1500

Japan - OsakaTel: 81-6-6152-7160 Fax: 81-6-6152-9310

Japan - TokyoTel: 81-3-6880- 3770 Fax: 81-3-6880-3771

Korea - DaeguTel: 82-53-744-4301Fax: 82-53-744-4302

Korea - SeoulTel: 82-2-554-7200Fax: 82-2-558-5932 or 82-2-558-5934

Malaysia - Kuala LumpurTel: 60-3-6201-9857Fax: 60-3-6201-9859

Malaysia - PenangTel: 60-4-227-8870Fax: 60-4-227-4068

Philippines - ManilaTel: 63-2-634-9065Fax: 63-2-634-9069

SingaporeTel: 65-6334-8870Fax: 65-6334-8850

Taiwan - Hsin ChuTel: 886-3-5778-366Fax: 886-3-5770-955

Taiwan - KaohsiungTel: 886-7-213-7828

Taiwan - TaipeiTel: 886-2-2508-8600 Fax: 886-2-2508-0102

Thailand - BangkokTel: 66-2-694-1351Fax: 66-2-694-1350

EUROPEAustria - WelsTel: 43-7242-2244-39Fax: 43-7242-2244-393

Denmark - CopenhagenTel: 45-4450-2828 Fax: 45-4485-2829

France - ParisTel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79

Germany - DusseldorfTel: 49-2129-3766400

Germany - KarlsruheTel: 49-721-625370

Germany - MunichTel: 49-89-627-144-0 Fax: 49-89-627-144-44

Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781

Italy - VeniceTel: 39-049-7625286

Netherlands - DrunenTel: 31-416-690399 Fax: 31-416-690340

Poland - WarsawTel: 48-22-3325737

Spain - MadridTel: 34-91-708-08-90Fax: 34-91-708-08-91

Sweden - StockholmTel: 46-8-5090-4654

UK - WokinghamTel: 44-118-921-5800Fax: 44-118-921-5820

Worldwide Sales and Service

07/14/15

http://support.microchip.com

http://www.microchip.com