SPECIFIERS GUIDE

Vector F40

2

Key Features ≤ 588lm/m 179lm/ft

≤ 9.36w/m 2.85w/ft

≤ 63lm/w

≤ 88 CRI

≤ 6m (19.5ft)

2600 / 2900 / 3300K CCT

PowerTHRU

12VDC CV

IP67

Overview

Vector F40

Cost effective IP67 lighting solution for linear or curved, wet or dry concealed lighting applications such as coving, backlighting, signage panels or illuminated stretch ceilings. Dimmable White Spectrum™ twin LED modules are spaced with exactly 40mm between each LED to provide a consistent line of light.

F40 can be specified ‘per metre’ in lengths of up to 6m (19.5ft) in series or longer lengths wired in parallel at 12VDC. Fixing via self-adhesive 3M mounting pads or mounting clips. Note: F40 is not suitable for exterior use when mounted in direct sunlight.

3

Applications

Images clockwise from top:

1. Oval concealed cove Corinthia Hotel London 2. Bar backlighting Ormer Restaurant Jersey 3. Concealed stairs Cultural Centre Baku 4. Bar underlighting Annabel’s Club London

F40 is ideally suited to concealed lighting applications such as coving, backlighting for stretched ceilings.

4

Performance

Performance Table 9.36W /m

CCT lumens /m lumens /w watts /m CRI R9

2600K 479 51 9.36 88 +56

2900K 588 63 9.36 60 -49

3300K 561 60 9.36 81 +30

Power rated at 12vdc. Data @25°C Ta

LED

3-Chip 5450 SMT package40.0mm mounting pitch

Light output ratio

1.00 LOR 115º beam angle

5

F40 module lumen output testing and photometric data conducted by independent UKAS accredited test laboratory, LUX-TSI. Test duration approx 20 minutes at ambient temperature of 24.4C with 24hr burn-in time. Stabilisation period, approx. 60 minutes. Humidity <65% RH.

0° 30°30°

60°

90°

120°

0° 30°30°

60°

90°

120°

C90°C0°

Polar DistributionCIE 1931 X & Y Chromaticity

y

4.15

4.05

4.10

4.70 4.804.75x

2600K

2 SDCM

dv

dh

1.0

2.0

3.0

5.0

4.0

6.0

m

216

54

24

9

14

6

lx

3.2

6.3

9.5

15.8

12.6

19.0

dv

3.1

6.2

9.3

15.4

12.3

18.5

dh

Illuminance at a distanceLumen maintenence @25°C Ta

10,000 50,00030,000hrs

120

100

80

60

40

20

lm%

L70

49,500hrs

Photometric Data

150cd

250cd

6

Dimensions

~130g per metre

40.0

0

10.00

12.00

22.0

058

.00

40.0

0

9.50

7

IDC Dimensions

Accessories

6.8

0

97. 9

15.3

2.65

2.65

OPEN - 8.75

CLOSED - 6.5

Water Resistant Connectors

VECA-CA901-R1 Twin pack IDC Sealant Connector

Discreet IDC connectors are used to join two wires together while maintaining a water resistant seal. The principle used is the insulation displacement technique while the silicon sealant used in the connector provides effective wa-ter & moisture protection, no wire stripping is required. Robust hand pliers can be used to crimp the connectors, however we recommend the use of Scotchlok™ Hand Crimping Tool E-9Y.

8

Drivers & Dimming

Dimming with 1-10V / DALI / DMX

F40 is ideally suited to dimming with 1-10V control signal using the Vector P12-100/180-D10 dim-mable driver. Alternatively a non-dimmable driver can be combined with a PWM interface suitable for 1-10V, DALI or DMX control.

12VDC

Wiring

F40 can be installed in power-through configuration lengths up to 6 metres subject to maximum ca-ble size and length. Longer lengths can easily be achieved by running parallel feeds as shown in the 10m (2 x 5m) example below.

12VDC

6m example

12VDC Driver Interface

max. 2m

Dim Signal

230VAC

VECTOR DIMMABLE DRIVER

230VAC

Dim Signal

10m (2x5m) example

9

Installation Notes

12VDC power supplies and dimming interfaces are often tested and verified to be EMI compliant with secondary cable lengths of up to 10m (shorter lengths on some devices). For cable lengths exceeding 10m, EMI emissions should be verified in the application. When EMI emissions exceed the allowed levels it may be possible to reduce them by using ferrite cores (not supplied).

12VDC cables should be shielded if longer than 10m total length. Recommended maximum cable lengths for dimmed circuits should be adjusted to allow a typical dimming interface voltage drop of 0.3V. Installers should check the specific voltage drop of the interface they are using and adjust cable length accordingly. A reduction of 10% in total cable length is normally sufficient.

*Recommended cable lengths shown are based on average resistance for typical copper solid core cables. Cable characteristics may vary acording to manufacturer, temperature, copper purity, connections etc. Installers must make their own checks to avoid voltage drop issues.

Drivers & Cabling

Drivers must be of constant voltage type providing 12VDC power supply. Recommended mini-mum driver wattage ratings are shown in the table below along with maximum recommended cable lengths. The performance of different cable types may vary and installers should check that at least 9.6V is maintained at the end of the F40 run.

It is recommended that only drivers with overload and short-circuit protection are used. Cable lengths should be reduced by 10% if dimming.

>1m>2m>3m>4m>5m>6m

0.781.562.343.123.904.68

F40 A

F40Length

9.3618.7228.0837.4446.8056.14

F40W

73m37m24m18m15m12m

117m59m39m29m23m20m

188m94m63m47m38m31m

300m150m100m75m60m50m

480m240m160m120m96m80m

0.5mm²20AWG

0.75mm²18AWG

1.0mm²17AWG

1.5mm²15AWG

2.5mm²13AWG

10

Wiring Examples

Switched

100W 12VDC DRIVER

Dim Signal

230VAC

100W P12-100-D10DIMMABLE DRIVER

230VAC

Dim Signal

Dimmed

230VAC

100W 12VDC DRIVER

12m max. [0.5mm² / 20AWG] 6m max.

6m max.

6m max.

Interface

10.8m max. [0.5mm² / 20AWG]

10.8m max. [0.5mm² / 20AWG]

11

Optional Double Fixing Mount

Optional Fixing Mount

Mounting Examples

Application Guide

150

50

170

F40S-MA520-R1 F40 Mount (x20) F40S-MA500-R1 F40 Mount (x100) F40S-MA800-R1 F40 Mount (x500) 11.50

13.7

5

Self-adhesive tape backing supplied as standard. Mounts are optional for additional security. Recommended quantity 6 per metre.

24

14.2

5

F40S-MA530-R1 F40 Twin Mount (x20) F40S-MA510-R1 F40 Twin Mount (x100) F40S-MA810-R1 F40 Twin Mount (x500)

Self-adhesive tape backing supplied as standard. Mounts are optional for additional security. Recommended quantity 6 per metre.

12

White Spectrum™ LED

Vector LEDs with White Spectrum™ technology benefit from ultra-fine LED x,y binning coordinates to precise specifications. Testing and control of these specifications gives very accurate control of correlated colour temperatures (CCT). White Spectrum™ technology also allows us to offer our high colour rendering index rating of 88 CRI (Ra) as standard for 2600K products.

Each 2600K Vector LED is ultra-fine binned from a defined x, y range bin area covering approximately 2 MacAdam steps. This is far smaller than the ANSI C78.377A Standard which equates to 7 Mac-Adam steps. This binning accuracy equates to a colour temperature precision of less than 2.0% tolerance giving approximately +/- 50K.

White Spectrum™ is one of the leading global LED technologies. A typical warm white fine-bin from another manufacturer is typically at least 40% larger than Lumino’s White Spectrum™ ultra-fine bin-ning.

0.39

0.43

0.41

0.41 0.490.470.450.43

2800K

VECTOR 2600K2-step MacAdam

ANSI C78.377A 2700K7-step MacAdam

2600K

LED Specification

13

Specification Codes

F 4 0 I E A-S 6 0 0 0 C- 1 AP A

LED CCT

CDF

2600K WS2900K WS3300K WS

Codes

14

Technology

Certification Standards

EN55015: 2006+A1 :2007

EN61547: 1995+A1 :2000

Following the provisions of EMC Directive 2004/108/EC

Material specifications

Injection moulded polycarbonate module housings PCB electroplated copper foil on FR4 substrate 20AWG wires stranded copper / PVC

Operating environment

Running Temperature (Tc): Ave. 17°C above Ta Ambient Temperature (Ta): -20 to +60°C Storage Temperature: -30 to +80°C Ingress Protection rating: IP67 IP67

15

The information in this document is subject to change without notice

Check for latest specifications at www.lumino.co.uk

Copyright © 2014 Lumino Limited

E&OE

Lumino Limited Lumino House, Lovet Road Harlow, Essex CM19 5TB United Kingdom

T +44 (0) 1279 635411 E info@lumino.co.uk

www.lumino.co.uk

Vector F40

SG-F40S-R1407