Upload
glyn
View
38
Download
1
Tags:
Embed Size (px)
DESCRIPTION
Vertical Alignment, Templates Cut / Fills Volume Table. Productive Lands -- Healthy Environment. Agenda Items. Horizontal Alignments Profiles Vertical Alignments Templates Profiles in Paper Space. Once you have your surface done and you have your contours lines. - PowerPoint PPT Presentation
Citation preview
Vertical Alignment, Templates Vertical Alignment, Templates Cut / Fills Volume TableCut / Fills Volume Table
Productive Lands -- Healthy Environment
Agenda ItemsAgenda Items
Horizontal AlignmentsHorizontal Alignments Profiles Profiles Vertical AlignmentsVertical Alignments TemplatesTemplates Profiles in Paper SpaceProfiles in Paper Space
Once you have your surface done and you have your contours Once you have your surface done and you have your contours lines.lines.
Draw a Polyline where your CL is going to be from node to Draw a Polyline where your CL is going to be from node to node starting at the upstream station.node starting at the upstream station.
Civil Design – Alignments - Civil Design – Alignments -
Station Label SettingsStation Label Settings
Civil Design – Alignments - Define from polylineCivil Design – Alignments - Define from polyline
Pick your Pline
Note: Make sure the first three boxes are checked, you can also check ‘Perpendicular labels” ; “Station read along road” and “Plus sign location” if you want, this will only change the appearance.
Civil Design – Alignments - Create Station Labels Civil Design – Alignments - Create Station Labels
If text is too small or too large, “rescale” itIf text is too small or too large, “rescale” itthrough; Utilities – Rescale - Block/textthrough; Utilities – Rescale - Block/text
Civil design – Profile - Civil design – Profile - Existing Ground -Existing Ground - Sample From SurfaceSample From Surface
Civil design – Profile - Civil design – Profile - Profile Settings - ValuesProfile Settings - Values
You will get a messageYou will get a message
****If you do not get this message you might have to start over**If you do not get this message you might have to start over**
Civil design – Profile - Civil design – Profile - Create Profile - Full ProfileCreate Profile - Full Profile
Civil design - Profile - FG Centerline Tangents - Civil design - Profile - FG Centerline Tangents - Create TangentsCreate Tangents
Vertical Alignment
Civil design – Profile - FG Vertical Alignment – Civil design – Profile - FG Vertical Alignment – Define FG CenterlineDefine FG Centerline
Civil design – Profile - Civil design – Profile - FG Vertical Alignment - FG Vertical Alignment - ImportImport
It will ask you to pick your profile and everything will disappear. Pick your Vertical Alignment. Hit enter and everything will show up again.
Your grades, PVI’s (Point of Vertical Inflection) and their elevations will now be labeled.
Civil Design - Cross Sections - Existing Ground - Sample Civil Design - Cross Sections - Existing Ground - Sample from Surfacefrom Surface
Civil Design - Cross Sections Civil Design - Cross Sections - View/Edit Sections- View/Edit Sections
Click ok
Click enter for all the values, enter a critical station you might want,
You will get a message that “You have sampled sections for 2207.8720 feet of alignment”.
After this you can plot the sections. Follow set of instructions attached.
Template for WaterwaysTemplate for Waterways
Civil Design - Cross Sections - Draw TemplateCivil Design - Cross Sections - Draw Template
CL AB
10’
Fig. 1 Template of 20’ waterway
Command Line
• Starting Point – Point A on Fig 1
• Select Point (Relative/Grade/Slope/Close/Undo/eXit) We’re selecting R
• Change in Offset (Grade/Slope/Close/Points/Undo/eXit) For our 20’ waterway template, type “-10”. Note: Be aware of the minus sign
• Change in elevation - Type “0”
• Type “C” for Close
Civil Design - Cross Sections – Templates - Civil Design - Cross Sections – Templates - Define TemplateDefine Template
Command Line
• Pick finish Ground reference Point - That would be the point attached to the center line of your profile, that would be point A in Fig. 1 Using osnaps, pick point A
• Is Template Symmetrical - Default “Yes”
•Select Objects - Pick your horizontal template line.
• You’ll get to the Surface Materials Names - Click ok
•Pick Connection point out – This will be point B in Fig. 1
• Pick Datum points (left to Right) - Pick first point B and then point A
• Hit “Enter”
• Save Template – Default “Yes” - “20’ww”
• Define another template (Yes/No) Type N and “Enter”
When you import the template, it will be applied to your finished ground profile at the grades you designed.
CL AB
10’
Fig. 1 Template of 20’ waterway
Civil Design - Cross Sections - Design Control - Civil Design - Cross Sections - Design Control - Edit Design ControlEdit Design Control
Continuation
Civil Design - Cross Sections - View/Edit SectionsCivil Design - Cross Sections - View/Edit Sections
Civil Design - Cross Sections - Point Output – Civil Design - Cross Sections - Point Output – Catch Points To DWGCatch Points To DWG
Command Line
• Import Catch Points (Y/N) – Type N “This will put actual datum points representing daylight lines on your drawing.
• Import daylight line (Y/N) – enter default “Yes”
Civil Design - Cross Sections - Total Volume Output -Civil Design - Cross Sections - Total Volume Output -Volume TableVolume Table
Command Line
• Volume Computation Type (Prismoidal/Avgendarea) – Enter default “Avgendarea”
• Use of Curve Correction (Y/N) Enter default “Yes”
•Leave the cut/fill adjustment factors at <1.00>. Pick an insertion point off your work space.
This will show up on your screen. Congrats!
Profiles in Paper SpaceProfiles in Paper Space
In our profile paper we will have a 2.5” by 2.5” main grid. We have to accommodate our profile length and height in this grid.
In our example it will be 2000 ft. of length and almost 50 ft. of height.
We will say 2000 ft. divided by 5 main grid spaces equals 400 ft.
Since each 2.5 by 2.5 square is divided into ten vertical strips, we will say that 1” = 160 ft. This is our horizontal scale.
Now, for the vertical part is the same, we have 50 ft. in three main grid spaces. That will lead us to use each square equals 20 ft. And since each square is divided also into ten horizontal strips, we will say that 1” = 8 ft. This is our vertical scale.
Now, we go back to model space and go to Project – Drawing Set up – Scale – Horizontal – Custom and type 160.0. We could change also the vertical scale here, but for this example we won’t. Also, if you go to Format – Text Style – Height – Type “your horizontal scale multiplied by the standard text height 0.0781”
When the Profile Generator prompts, we will change four things. The Datum, we will change it to something close to the minimum. Also here is where we are going to change the vertical scale to 8.0 Horizontal spacing will be whatever number you came up for the horizontal main grid divided by 10. And the vertical spacing will be 1.
QuestionsQuestions