ZTE Narrow Band Data Configuration

8/10/2019 ZTE Narrow Band Data Configuration

1/20


2/20

2

Objectives:

1. master narrow band data configuration

2. Master H.248 protocol


3/20

3

Delete original data

The rack maybe have some original data, so we need to delete them .allsystem data is backup on floder E: \DATA\V0100 and V0101.

1. telnet 129.0.52.51 8888 (129.0.52.51 is the outband IP address)

2. passwordzxmg

3. change the data attribute into read and write r06_attr E:/DATA/V0100/*.* -R

r06_attr E:/DATA/V0101/*.* -R

4. delete data: r06_del E:/DATA/V0100/*.*

r06_del E:/DATA/V0101/*.*

r06_del D:/durable

r06_del D:/persist

5. comfirm all data is empty. ftp 129.0.52.51

user name and password are root CD E:\DATA\V0100

LS

CD E:\DATA\V0101

LS

Then all data should be empty.
ftp://ftp%20129.0.52.51/ftp://ftp%20129.0.52.51/ftp://ftp%20129.0.52.51/ftp://ftp%20129.0.52.51/


4/20

4

Contents:

Lab equipment allocation

Data preparation

Data configuration

Check MSAG running status


5/20

5


SUN server :168.2.16.1

129.0.22.1

26NIC

10.66.22.1

28NIC SSNI

COL-

ACT-

STA-

1 2 34 5 6 7 8 9101112

HS1 HS2 OK1 OK2 PSCONSOLE

COL-

ACT-

STA-

1 2 3 4 5 6 7 8 9101112

HS1 HS2 OK1 OK2 PSCONSOLE

129.0.100.1

10.76.100.1

129.0.100.5

10.76.100.5

1 5200 port

of backboard

10.76.52.51

7 5200 port of

backboard

10.76.52.57

1 5200 port of

front board

129.0.52.51

7 5200 port

of front board

129.0.52.57

GW:10.66.25

4.254

GW

10.76.254.253


6/20

6

Data configure interface

interface function notes Switch

SHELL debugging Only two

command can

be supported:

routeShow and

sysReboot

exit

MSAG# Can use

show

command

Config switch to MSAG(config)#

Ag switch to MSAG(ag)#

MSAG(config-a

g)#

Or

MSAG(ag)#

Hardware

and

narrowban

d data

configurati

on

Exit switch to MSAG#

MSAG(config)# Board band

data

configurati

on

Ag switch to MSAG(config-ag)#;

Epon switch to PON configuration interface

.

Logout to exit the configuration

end exit to MSAG#;


7/207

Contents:


Data preparation

Data configuration



8/208

Data preparation

SS typeZXSS10 or other SS;

SS IP address

MSAG IP address and mask

MSAG next hop

The VLAN of Uplink exchange port (tagged or untagged and

VLANID)

Protocol type (H.248) and port (2944)

Terminal ID and RTP resources


9/209

Data configuration

Enter 1123 port


10/2010

Configure physical location

Add rack

MSAG(ag)# add-rack rack 1 type 1

Add shelf

MSAG(ag)# add-shelf rack 1 physhf 0 type 6 Configure control board (Add main shelfs ICS)

MSAG(ag)# add-board-mics slot 9 type 1


11/2011

Configure physical location

Configure MGC

MSAG(ag)# add-mgc mgcid 1 mgctype 1 mgcip 10.61.252.100 mgcport2944

MSAG (ag)# mod-call subpriority 2

Configure media, control and management IP address

Plan 1: 5200 only have one IP address.media, control and managementIP is the same IP address

Plan 25200 configure 2 IP address, control and media IP address is thesame ip address, and management IP address is the other IP address.

Plan 3:5200 configure 2 IP address, media IP address uses one IP

address, but control and management IP address is different IP address. Plan 4:5200 configure 3 IP address respectively.

Plan 5: 5200 configure one management IP address. It have not narrowband functions.


12/2012

Plan 1: one IP

1. configure media IP

MSAG(ag)# add-voip-interface type 1 ipaddr 10.61.252.55

submask 255.255.252.0

2. configure media gateway

MSAG(ag)# add-voip-route nexthop 10.61.252.254

MSAG(config)# vlan add 120

MSAG(config)# vlan add-port 120 port 0/9/0 untagged

MSAG(config)# vlan voipmed add 120

3. configure protocol and ports

MSAG(ag)# add-mg mgport 2944 mgcid1 1


13/2013

Uplink interface enable

MSAG(config)# port enable 0/9/0

Add AG protocol capability

MSAG(ag)# add-mgcapabili faxpri1 faxpri2


14/2014

Configure subscriber resources

Add ALC

MSAG(ag)# add-board-slc slot 3 type 26

Add TERMINATION ID

Type one: zte SS type

MSAG(ag)# add-slctermid rack 1 shelf 0 beginslot 3 beginindex 0

num 32 tmidfix USER type 1

Type two: huawei ss type

MSAG(ag)# add-slctermid rack 1 shelf 0 beginslot 3 beginindex 0num 32 tmidfix A type 2 begno 0

Type three: length is fixed and configurable.

MSAG(ag)# add-slctermid rack 1 shelf 0 beginslot 3 beginindex 0num 32 tmidfix USER type 3 digitlen 4 begno 0

Configure VOIP resources

MSAG(ag)# add-board-mpr slot 11

MSAG(ag)# add-board-mprb slot 12


15/2015

Add VOIP TERMINATION ID

Type 1:

MSAG(ag)# add-ipstermid slot 11 subcard 1 tmidfix RTP

Type 2:

MSAG(ag)# add-ipstermid slot 11 subcard 1 tmidfix RTP type

2 begno 0

Type 3:

MSAG(ag)# add-ipstermid slot 11 subcard 1 tmidfix RTP type

3 digitlen 3 begno 0


16/2016

Add media route configuration

MSAG(ag)# add-mednat mprslot 11 mprsubcard 1 nicslot 9

inphyport 5 exphyport 5 exipaddr 10.61.252.201 udpport 6000

MSAG(ag)# add-mednat mprslot 11 mprsubcard 2 nicslot 9

inphyport 5 exphyport 5 exipaddr 10.61.252.201 udpport 8000

the IP address is media IP address.

The minmam value of UDPPORT is 6000. every subcard needs 2000 ports.


17/2017

Configure jiter of MPRB

MSAG(ag)#mod-rtppar-mprb parid 1 mindelay 20 maxdelay 120

nomdelay 20

SAVE DATA

MSAG(config)# save


18/2018

Contents:


Data preparation

Data configuration



19/2019

telnet 129.0.52.1 8888 password: zxmg

1. 0x1389>pe

Cards on Slot 9,11 and 12 are active.

The last row has 0x1309 item, which means NIC is normal.

2. 0x1389>unit 1

3. 0x1389>h248s link OK means H248 link OK.

4. r07_vershow

Check different card version.

5. cpu

6. cpuclear 7. ppreset

8. changeover querystate


20/20

univ.zte.com.cn

Documents

ZTE Narrow Band Data Configuration