Genex assistant operation guide (lte)

内部公开华为机密，未经许可不许扩散

GENEX Assistant Operation Guide (LTE)

Shui Chenglin/00133924July 08, 2009


Contents

GENEX Assistant IntroductionGENEX Assistant Introduction

GENEX Assistant Installation GuideGENEX Assistant Installation Guide

GENEX Assistant License ManagementGENEX Assistant License Management

GENEX Assistant Project ManagementGENEX Assistant Project Management

GENEX Assistant Data ImportGENEX Assistant Data Import

GENEX Assistant View of Test ResultsGENEX Assistant View of Test Results

GENEX Assistant Geographic DisplayGENEX Assistant Geographic Display


Contents









GENEX Assistant Introduction

The GENEX Assistant (hereafter referred to as Assistant) is an expert radio test data post-processing software. It is used for analyzing and processing the test data (both drive test data and RNC data) of radio network air interfaces. The Assistant can also generate analysis reports. The Assistant helps network planning and network optimization engineers learn about network performance and efficiently analyze network problems. This helps improve their work efficiency. The Assistant benefits customers with respect to the following aspects:

Quickly and efficiently obtaining the QoS of the entire network Reducing the test workload required by network adjustment Providing profound and effective problem location information. Providing sharable analysis methods, and thus reducing the requirements for t

he skills of network optimization personnel

Contents


The GENEX Shared must be installed before you install the GENEX Assistant. The GENEX Shared is a common component of Huawei GENEX network planning and network optimization solution software.

After the Assistant is installed, you must apply for a license. If the license expires, you must reapply for the license.

When performing tests, the projects that are created in the current version of the Assistant must be used. Otherwise, unexpected problems may occur.

The Windows XP operating system must be used. Otherwise, unknown problems may occur.

Precautions to be Taken When installing the GENEX Assistant

Contents


Contents









The running of the Assistant needs the support of the GENEX Shared.When you uninstall the Assistant main program, the GENEX Shared is not uninstalled accordingly. This ensures that the other products of the GENEX series run normally.If you have installed the Assistant on your PC, you can ignore the installation of the GENEX Shared when you reinstall the Assistant.

To install the GENEX Shared, perform the following steps:Open the installation CD of the GENEX Shared, and then double-click setup.exe to display the installation interface.Click Next.In the agreement dialog box, click Yes.After the installation is complete, click Finish.

After you install the GENEX Shared, the following components are installed:

MapX component: used for processing maps.TeeChart component: a control used for developing icon interfaces.OWC component: a series of controls used for issuing electronic tables, charts, and database to Web.Dongle lock driver: used for maintaining version authorization.

GENEX Shared Installation (I)


GENEX Shared Installation (II)

Double-click Setup.exe that is in the installation folder of the GENEX Shared.

Contents


GENEX Shared Installation (III)GENEX Shared Installation (III)

The window will appear for about one to two minutes. Please wait until it disappears.

Contents


GENEX Shared Installation (IV)GENEX Shared Installation (IV)

Click Next to continue.

Contents


GENEX Shared Installation (V)GENEX Shared Installation (V)

Click Yes to continue.

Contents


GENEX Shared Installation (VI)GENEX Shared Installation (VI)

The installation is in progress.

The window will appear for about one to two minutes. Please wait until it disappears.

Contents


GENEX Shared Installation (VII)GENEX Shared Installation (VII)

The installation is complete.

Click Finish to exit.

Contents


GENEX Assistant InstallationGENEX Assistant Installation

To install the main program of the Assistant, perform the following steps:

Open the installation CD of the software, and then double-click setup.exe to display the installation window.

Click Next.

In the agreement dialog box, click I accept the terms of the license agreement.

Click Next.

In the displayed dialog box, set User Name and Company Name.

Click Next.

In the displayed dialog box, click Change to set the installation path.

After the installation path is set, click Next.

Click Install. The installation starts.

Click Finish. The Assistant is installed successfully.

Contents


Contents









Applying for and Importing a LicenseApplying for and Importing a License

Start the Assistant when no license is installed.

The following window is displayed.

Record the ESN in the window. Then, fill in the License Application Template and send a mail to liufengzhen 00126279/huawei to apply for a license.

After the license file is obtained, click Update License to import it.

Contents

License Application Template


Viewing License InformationViewing License Information

Choose Help > View License.

Contents


Contents









GENEX Assistant Main Window

Contents


Project Management ---- Creating a ProjectProject Management ---- Creating a Project

Choose Project > New Project.

Set the path of the map. After this path is set, all the datasets of this project can share this map. You can also set this path after the project is created.

Contents


Project Management ---- Creating a DatasetProject Management ---- Creating a Dataset

Choose Dataset > New Dataset.

Contents


Contents









Data Import ---- GENTo import the data of the GENEX Probe into the Assistant, perform the following

steps:

Click the Project tab in the navigation pane, and then right-click a dataset.

Choose Import Test Data > Import GENEX Probe from the shortcut menu. The Import GENEX Probe File dialog box is displayed.

In the dialog box, perform the following operations:

Click Browse to select one or more test files of the GENEX Probe.

Select Automatic Combine By Comport to combine the test data of the same port together.

Click Import and wait until importing the data is complete.

Contents


Data Import ---- LMTTo import the data of the LTE LMT into the Assistant, perform the following steps:

Click the Project tab in the navigation pane, and then right-click a dataset.

Choose Import Test Data > Import LTE LMT. The Import LMT File dialog box is displayed.

In the dialog box, perform the following operations:

Click Browse to select a .txt file.

From the Indicator Name drop-down list box, select a counter name.

From the Merge Stream dialog box, select the LTE terminals to be analyzed together.

From the Import UE ID drop-down list box, select the terminal IDs to be imported.

Click Import and wait until importing the IDs is complete.

Contents


Contents









After the data of the LTE is imported, the counters in the projects are displayed as follows:

View of Test Results ---- Navigation Tree

Contents


View of Test Results ---- View

The Assistant provides six data display modes. See the figure on the right.You can right-click a counter in the navigation tree and then select the display mode of the data corresponding to the counter.

In each display mode, data can be displayed in two ways:In a new window: Used to display data sepa

rately.In the active window: Used for data compar

ison. For example, displaying the Serving_RSRP counter on the active sheet.

Contents


View of Test Results ----View

Option Function

Display on Map Display data on a map.

Display on Chart Display data in a chart where x axis represents time and y axis represents values.

Display on Caky Display statistical data in a pie chart.

Display on Histogram Display statistical data in a column chart.

Custom Display on Chart Display data in a chart where x axis and y axis are self-defined. You can select the corresponding submenus to define x axis and y axis. Then, the Assistant displays a window containing the defined chart.

Display on Active Sheet Display data in the active window.

Compare with Local A or Compare with Local B

Used to compare the counters of two datasets in a project.

Contents


View of Test Results ---- Map

Displaying counter values geographically

Contents


View of Test Results ---- Sheet

Displaying counter values in a list

Contents


View of Test Results ---- Chart

Displaying counter values in a curve chart

Contents


View of Test Results ---- Caky

Displaying counter values in a pie chart

Contents


View of Test Results ---- Histogram

Displaying counter values in a column chart

Contents


View of Test Results ---- Scatter ChartDisplaying counter values in a scatter chart

You can define the X axis and Y axis as required.

Contents


View of Test Results ---- Comparison ChartIn the Assistant, you can display the values of different counters in one chart. You can also display the values of one counter in different test data in a chart for comparison.

Contents


Contents









To import a map, choose Project > Set Map Path.

Before changing a map, you must remove the original map. To remove an original map, choose Project > Remove Map Path.

After you import a map, the map window is not automatically displayed if the following dialog box is displayed. To view the map, you need to import the corresponding data. Then, select a counter to view the geographic display results of the counter. For details, see View of Test Results ---- Map.

Geographic Display ---- Map Import

Contents


In the navigation tree, select a dataset. Choose Dataset > Engineering Parameter Management > LTE.

Geographic Display ---- Engineering Parameter Import (I)

Contents


The column headings in the engineering parameter file may be different from the default column headings in the Assistant. The Assistant cannot automatically match the different column headings, for example, PCI in the following figure. In this case, you need to manually match them.After all required column headings are matched, click Importing the Execute Data to complete the import. For details, see the following figure.

Geographic Display ---- Engineering Parameter Import (II)

Contents


For details, see View of Test Results ---- Map.

Result Display

Contents


In the Assistant, you can determine whether to display counter values on maps. By default, counter values are not displayed on maps. On the toolbar in the map window, click . Alternatively, right-click any area in the map window, and then choose Layer Control from the shortcut menu.

Result Display ---- Layer Control (I)

Contents


You can define the labels of BTSs. For example, change the label of a BTS to any entry in the engineering parameter file. The default value of a BTS label is Cell ID.

Result Display ---- Layer Control (II)

Contents


After engineering parameters are imported, display them geographically. Then, you can view the serving cell corresponding to a counter dot. After selecting a dot, the Assistant connects the dot and the serving cell corresponding to it.

Result Display ---- Cell Connection

Contents


The data in different windows of the Assistant can be co-activated. When you select a data item in one window, the values of the same item at the same time in other windows are highlighted simultaneously.

Result Display ---- Cooperation

Contents


Legend Modification (I)

The Assistant provides the function of modifying the default legend.

Contents


Legend Modification (II)

If the modified legend does not meet your requirements, you can reset the legend in the following way:

Contents


Technology

Genex assistant operation guide (lte)