Upload
khangminh22
View
1
Download
0
Embed Size (px)
Citation preview
High Speed Production + High Quality Tightening
yokota
Impulse wrenches
System wrenches
Poka Yoke+
(Non-) shut-off tools
Cordless impulse wrenches
Sleeve Drive sockets
Accessories
HIGH SPEED PRODUCTIONHIGH QUALITY TIGHTENING
yokota
www.rami-yokota.com
www.tid-extra.hr
WWW.RAMI-YOKOTA.COM 32 WWW.RAMI-YOKOTA.COM
High repeatabilityImpulse wrenches have a twin blade impulse mechanism for sealing oil which gives a high repeatability. The mechanism is designed so that the liner, rotated by the air motor gives an equal torque on both blades and instant rotation torque on the mainshaft (see figure below). A by-pass is designed in the liner so that the oil can escape from the area of high pressure to the area of low pressure at the moment of creating a pulse and the amount of oil flow can be adjusted by the relief valve to control the torque output. Depending on model and setting, the impulse wrenches give 10 - 40 impulses per second. The power is transmitted by oil pressure and therefore the impulse wrenches have a very low noise- and vibration level.
Double chamber air motor
The Yokota Y-, YLa, YLT, YED- and TKa-series impulse wrenches with double chamber air motor reach the required torque very quickly. The tools have a high number of impulses per second, and therefore very accurate torques can be realized, resulting in increased production speed.
Patented twin blade impulse unit. Yokota‘s unique
impulse mechanism reduces noise and vibration!
High impulse frequency.
Faster Yokota impulse wrenches are widely used for tightening jobs in the assembly industry, where accurate torque tolerances are necessary. Impulse tools are light, power-ful, small and very importantly, have no kick-back. The Yokota range of impulse tools is increasing fast, starting at 6 Nm to tighten small joints, and goes up to 600 Nm. Evaluation of tightening processes in car assembly shows that tightening joints uses 10% of the total assembly time. Working with faster tools therefore can speed up assembly lines substantially.
High accuracyProduct liability is essential to carmakers. All tighte ned joints have to be correct. For this reason critical joints must be counted, documented and, of course, tightened with the right clamping force. In order to do this, you need an impulse wrench (with a built-in transducer) con-nected to a controller. This system ensures that only OK joints are counted resulting in "Zero Fault Production". This
fail-safe system fits perfectly in the Poka Yoke Strategy.
Contents Joint Quality
In Out
Out In
Out
Out
DIN 267* 3.6 4.6 4.8 5.8 8.8 10.9 12.9
Bolt Socketsize
Torque Nm
Torque Nm
Torque Nm
Torque Nm
Torque Nm
Torque Nm
Torque Nm
M1,6 - 0,05 0,065 0,086 0,11 0,17 0,24 0,29
M2 - 0,10 0,13 0,17 0,22 0,35 0,49 0,58
M2,2 - 0,13 0,017 0,23 0,29 0,46 0,64 0,77
M2,5 - 0,20 0,26 0,35 0,44 0,70 0,98 1,20
M3 - 0,35 0,46 0,61 0,77 1,20 1,70 2,10
M3,5 - 0,55 0,73 0,97 1,20 1,90 2,70 3,30
M4 7 0,85 1,1 1,5 1,9 2,9 4,1 4,9
M5 9 1,7 2,2 3,0 3,7 6 8,5 10
M6 10 2,9 3,9 5,1 6,4 10 14 17
M8 13 7 9,3 12 16 25 35 41
M10 17 14 19 25 31 49 69 83
M12 19 24 32 43 54 86 120 145
M14 22 39 51 68 86 135 190 230
M16 24 59 79 105 130 210 295 355
M18 27 81 110 145 180 290 405 485
M20 30 115 155 205 255 410 580 690
M22 32 155 205 275 345 550 780 930
M24 36 265 200 350 440 710 1000 1200
M27 41 295 390 520 650 1050 1500 1800
M30 46 395 530 710 880 1450 2000 2400
M33 50 540 720 960 1200 1900 2700 3250
M36 55 690 920 1250 1550 2450 3450 4150
* These torque values are only guide lines and are calculated with friction factor 0,125.
Guideline values for tightening torques
Assembly toolsYokota Yokota Industrial Co. Ltd. (Japan) is making great effort to provide high quality and performance airtools for all industries. The modern technology is resulting in a high quality production system, based on 70 years of expe-rience. The company is internationally orientated and active in global sales. The production of the Yokota air-tools meet the demands of the 21th century. All develop-ments are based on original and flexible ideas. The Yokota strategy is that development with team spirit, flexible ideas and young power will bring the best solu-tions. With all this research and developments Yokota is contributing to a better environment for the operator.
High
LowHigh
Low
PAGE
Guideline values 2Joint Quality 3How to use 4What to choose 5
YLT serie: Shut-off 6
YLa serie: Non shut-off 7
Y serie: Non shut-off 8Double chamber air motor
YX serie: Non shut-off 9Pistol models
Angle models
Straight models
Battery impulse wrenches 11Electronic controlled shut-off
Non shut-off
Poka Yoke+ system 12
YLa-JQ serie 13Lightweight YLa-JQ series
Y-JQ series
Yokota Multi Fastening Controller 14
Yokota system wrenches 15
System wrenches TKa - YED series 16
System wrenches YEX series 17
Accessories 18
Sleeve Drive Sockets 20
Impact sockets for screwdrivers 26
(Spring) balancers & Specials 27
Advantages of the Yokota Impulse Wrenches:
Joint QualityMeeting Seal Lines
Crossing Seal lines Crossing Seal lines
Meeting Seal Lines
Motor rotation
BladesMain shaftLinerLiner caseBy-pass oilRelief valve
Smaller
High repeatability
High accuracy
Faster
Lighter
Very powerfull
No kick back Low vibration
Low noise
Ecology
The tools are innovatively designed, paying
the highest attention to the environment and
its safeguard.
All the components are easy to dispose of, because they
are built with recyclable materials. Therefore they do not
present any danger in terms of environmental pollution.
Models with automatic air shut-off reduce the cycle time
and therefore the compressed air consumption.
www.tid-extra.hr
Impulse wrenches without shut-off
Impulse wrenches archive the highest quality joint if the
tightening is finished in this area (horizontal part of the
torque curve)
• Highestclampforcewithsmallesttolerances
• Smallesttorquetolerances
Impulse Wrenches with mechanical shut-off
Mechanical shutt-off
• Shorteroperatingtime
•Operatorknowswhenthetighteningisfinished
• Highestclampforcewithsmallesttolerances
• Smallesttorquetolerances
Impulse Wrenches with integrated torque transducer
Impulse wrench with torque transducer integrated• Highestclampforcewithsmallesttolerances
• Smallesttorquetolerances
• Shortestoptimumoperatingtime
•Operatorknowswhenthetighteningisfinished
•OperatorisinformedaboutOK-NOKofthetightening
•OKjointsarecounted,nomissedtightnings
• Actualtighteningtorqueismeasured
• Fulldocumentation
• Zerofaultproduction
How to use What to choose?
sec
Nm
4 WWW.RAMI-YOKOTA.COM
The transducer for the YEX, YED and TKaThe strain gauges are positioned on
the main shaft, picking up the twisting
torque on the main shaft at each impulse
as close as possible to the socket. The
electric signals are transmitted by induc-
tion through the internal- and external
coils. Due to this principle the Yokota
transducer is very reliable, accurate and
without wear.
Optional on TKa System Wrenches:integrated LED status-signal:
• Green = OK • Red = not OK
Visible from every angle: left, right, from top and behind.
WWW.RAMI-YOKOTA.COM 5
Save time - save moneyBecause of the principal of
using hydraulics to reach a
certain torque, impulse tools
can run at a high rpm. The
required torque is reached
in a split second. All Yokota
impulse wrenches can be used
for hard and soft joints, and
give a high accuracy / repeat-
ability and a low relaxation.
Time saving
Nutrunner
Time
Impulse toolNm
Area where the impulse wrench automatically shuts-off
sec
Nm
Ideal area to stop the tightening
sec
Nm
Ideal area to stop the tightening
Impulse Wrenche with Poka Yoke+ system
Impulse wrench with controlled shut-off
• Highestclampforcewithsmallesttolerances
• Smallesttorquetolerances
• Shortestoptimumoperatingtime
•Operatorknowswhenthetighteningisfinished
•OperatorisinformedaboutOK-NOKofthetightening
•OKjointsarecounted,nomissedtightnings
sec
Nm
Ideal area to stop the tightening
Specified torque rangeThe specified torque range is measured in the laboratory under standard condi-
tions. Therefore these torque figures are only to be used as a guidance.
The actual torque range is depending on a variety of working conditions, eg: air
pressure, joint hardness, used accessory.
The torque ranges are specified at a dynamic air pressure of 0.6 MPa, lower air
pressure will result in lower torque. Please take note that these impulse wrenches
are developed for a dynamic air pressure of 0.63 MPa maximum.
Shut-of impulse wrenches selection:• Hardjoint:torquelevelsupto100%ofthespecifiedtorquerange
• Softjoint:torquelevelsupto90%ofthespecifiedtorquerange
Non shut-off impulse wrenches selection:• Hardjoint:torquelevelsupto95%ofthespecifiedtorquerange
• Softjoint:torquelevelsupto85%ofthespecifiedtorquerange
Accessories:The size and shape of impact sockets influence the torque result.
Extension bars, depending on the length, can lower the torque range with
5-30%Innertorxandinnerhexagoncanlowerthetorquerangewith5-20%
For the best result of the impulse wrench, use:• Constantstabilizedairpressure
• Sleevedrivesockets,impactquality(seepages20-25)
• Impactqualityaccessorieswiththecorrectdimensions
• Accessoriesingoodcondition
•Correcthoseinnerdiameterandlength
•Lubricatedair
Weadvisetousetheimpulsewrenchupto80%ofit’scapacityforthehighest
productivity, accuracy and durability.Soft joint, typical example
Adjustment of torque level of the tool.
Hard joint, typical example
<30°
sNm
<720°
sNm
www.tid-extra.hr
WWW.RAMI-YOKOTA.COM 7
Double chamber air motor, lightweight
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s2
Noise-leveldB(A)
YLa60A 1/4" Hex 6 4.000 9 - 20 5 5,5 0,78 PT 1/4" 6,5 130 22 1,4 71
YLa70A 1/4" Hex 6 - 8 7.000 20 - 28 5,5 6,1 0,8 PT 1/4" 6,5 132 22 1,4 74
YLa80A 1/4" Hex 8 7.000 24 - 35 5,8 9 0,9 PT 1/4" 6,5 139 22 1,2 75
YLa60E 3/8" Sq. 6 4.000 13 - 22 5 5,5 0,78 PT 1/4" 6,5 130 22 1,4 71
YLa70E 3/8" Sq. 6 - 8 7.000 20 - 35 5,5 6,1 0,8 PT 1/4" 6,5 132 22 1,4 74
YLa80E 3/8" Sq. 8 7.000 33 - 50 5,8 9 0,9 PT 1/4" 6,5 139 22 1,2 75
YLa90E 3/8" Sq. 8 - 10 6.500 47 - 70 6,7 11,8 1,0 PT 1/4" 10 148 24 1,2 78
YLa110E 1/2" Sq. 10 - 12 6.000 65 - 105 9,6 13,1 1,4 PT 1/4" 10 164 26 1,8 81
YLa120E 1/2" Sq. 12 6.600 80 - 130 10 15,6 1,8 PT 1/4" 10 172 28 2,2 82
YLa140E 1/2" Sq. 14 6.000 100 - 160 13 18,9 2,2 PT 1/4" 10 190 30 2,4 84
6 WWW.RAMI-YOKOTA.COM
YLa serie: Non shut-offYLT serie: Shut-offShut-off Impulse wrench
0,5 - 0,6 MPa series
0,4 - 0,5 MPa series
Note: Torque values are to be used as guidance only.
YLT50A YLT60A YLT70A
YLT50E YLT60E YLT70E YLT80E
YLa60E YLa70E YLa80E YLa90E YLa110E YLa120E YLa140E
YLT140E YLT150 YLT110E YLT120E
•Maximumaccuracy: extreme accurate and fast Repeatability, new principle: shut-off valve and reset•Maximumdurability:check valve mechanism reduces load on the O-ring inside the oil pulse mechanism•Maximumergonomics: Ergo touch / Ergo grip / Ergo trigger•Maximumenvironment: Reduction of CO2 emission / Low noise / Low vibration•Doublechamberairmotor:compact high efficiency•Oil-free:can be used with non lubricated air
FEA
TUR
ES
Rubber protection covers for all YLT-series impulse wrenches are included in the box.
All YLT models are available as J-version: signal hose for detecting shut-off, to connect to counting systems (PLC), line control etc.
YLT
-J
D IMENSIONS•Maximumaccuracy: extreme accurate and fast •Maximumdurability: check valve mechanism reduces load on the O-ring inside the oil pulse mechanism •Maximumergonomics: ergo touch / Ergo grip / Ergo trigger•Maximumenvironment: reduction of CO2 emission / Low noise / Low vibration•Doublechamberairmotor: compact high efficiency•Oil-free: can be used with non lubricated air
FEA
TUR
ES
B
A
Rubber protection covers for all YLa-series impulse wrenches are included in the box.
Type Square/hex drive
Boltcapacity
mm
RPM TorqueNm*
0,5-0,6 MPA
Loadaircons.
l/s
No-loadaircons.
l/s
Inlet-thread
Weightkg
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s2
NoiseleveldB(A)
YLT50A 1/4" Hex 5 4.300 4,5 - 8 4,2 4,6 PT 1/4" 0,95 6,5 164 22,5 1,1 70
YLT60A 1/4" Hex 6 5.300 6,0 - 13,0 5,5 5,6 PT 1/4" 0,95 6,5 164 22,5 1,4 72
YLT70A 1/4" Hex 6 - 8 6.800 13,0 - 28,0 6,0 8,8 PT 1/4" 1,01 6,5 177 23 1,8 74
YLT50E 3/8" Square 5 4.300 4,5 - 8 4,2 4,6 PT 1/4" 0,95 6,5 164 22,5 1,1 72
YLT60E 3/8" Square 6 5.300 7,0 - 15,5 5,5 5,6 PT 1/4" 0,95 6,5 164 22,5 1,4 72
YLT70E 3/8" Square 6 - 8 6.800 15,0 - 32,0 6,0 8,8 PT 1/4" 1,01 6,5 177 23 1,8 74
YLT80E 3/8" Square 8 6.800 30,0 - 55,0 7,3 9,2 PT 1/4" 1,12 10 187 24,5 1,9 78
YLT110E 1/2" Square 10-12 5.800 50 - 85 8,3 13,5 PT 1/4" 1,51 10 194 28,5 1,8 81
YLT120E 1/2" Square 12 5.400 70 - 115 8,6 14,6 PT 1/4" 1,79 10 201 31 2,2 83
YLT140E 1/2" Square 14 5.200 110 - 150 11,8 16,6 PT 1/4" 2,08 10 214 32,5 5,2 85
YLT150 3/4" Square 16 4.400 140 - 210 11,8 17 PT 1/4" 2,95 10 237 38,5 6,2 85
Type Square/hex drive
Boltcapacity
mm
RPM TorqueNm*
0,4-0,5 MPA
Loadaircons.
l/s
No-loadaircons.
l/s
Inlet-thread
Weightkg
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s2
NoiseleveldB(A)
YLT60AL 1/4" Hex 6 4.500 5,0 - 11,5 5,5 4,8 PT 1/4" 0,95 6,5 164 22,5 1,4 72
YLT70AL 1/4" Hex 6 - 8 6.300 11,0 - 25,0 6,0 7,8 PT 1/4" 1,01 6,5 177 23 1,8 74
YLT60EL 3/8" Square 6 4.500 6,0 - 13,5 5,5 4,8 PT 1/4" 0,95 6,5 164 22,5 1,4 72
YLT70EL 3/8" Square 6 - 8 6.300 13,0 - 28,0 6,0 7,8 PT 1/4" 1,01 6,5 177 23 1,8 74
YLT80EL 3/8" Square 8 6.600 25,0 - 48,0 7,3 8 PT 1/4" 1,12 10 187 24,5 1,9 78
YLT110EL 1/2" Square 10-12 5.600 45 - 75 8,3 11,8 PT 1/4" 1,51 10 194 28,5 1,8 81
YLT120EL 1/2" Square 12 5.200 60 - 100 8,6 12,3 PT 1/4" 1,79 10 201 31 2,2 83
YLT140EL 1/2" Square 14 4.900 80 - 125 11,8 14,1 PT 1/4" 2,08 10 214 32,5 5,2 85
D IMENSIONSRUBBER PROTEC T ION COVER
YLa60A YLa70A YLa80A
www.tid-extra.hr
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s2
Noise-leveldB(A)
YX-180E 3/8" Sq. 4 - 6 10.500 19 - 31 4,2 7,8 1,00 PT 1/4" 6,5 169 23 3 72
YX-180A 1/4" Hex 4 - 6 10.500 18 - 30 4,2 7,8 1,00 PT 1/4" 6,5 169 23 3 72
YX-280E 3/8" Sq. 6 - 8 10.500 25 - 38 5,0 9,1 1,02 PT 1/4" 6,5 180 23 2 70
YX-280A 1/4" Hex 6 - 8 10.500 20 - 34 5,0 9,1 1,02 PT 1/4" 6,5 180 20 2 70
YX-380E 3/8" Sq. 8 10.000 34 - 47 5,0 9,1 1,24 PT 1/4" 6,5 180 25 2,1 75
YX-380A 1/4" Hex 6 - 8 10.000 29 - 44 5,0 9,1 1,24 PT 1/4" 6,5 180 25,5 2,1 75
YX-500E 3/8" Sq. 8 - 10 8.200 31 - 55 5,8 11,2 1,40 PT 1/4" 6,5 173 26,5 2 68
YX-700E 3/8" Sq. 8 - 10 8.000 45 - 78 6,7 13,5 1,60 PT 1/4" 10 185 26,5 2 68
YX-900E 1/2" Sq. 10 6.500 70 - 111 6,7 12,8 2,00 PT 1/4" 10 201 30,5 2 72
YX-1100E 1/2" Sq. 10 - 12 4.700 85 - 123 7,5 13,6 2,20 PT 1/4" 10 210 30,5 2,5 72
YX-1400E 1/2" Sq. 12 - 14 6.000 102 - 148 8,3 15,1 2,70 PT 1/4" 10 214 33,5 2,6 78
YX-1900E 1/2" Sq. 12 - 14 5.800 140 - 201 8,3 15,1 3,40 PT 1/4" 10 224 35,5 3 79
YX-2400E 1/2" Sq. 14 - 16 4.200 175 - 279 9,2 16,8 4,10 PT 1/4" 10 236 37,0 5,3 77
YX-3000 3/4" Sq. 16 - 18 4.700 200 - 304 10,0 20,5 4,60 PT 1/4" 13 246 40,0 3,9 80
YX-4500 3/4" Sq. 18 - 20 3.400 392 - 490 11,6 24 9,80 PT 3/8" 13 300 65,0 3,9 87
YX-180E/AYX-280E/AYX-380E/A
YX serie: Non shut-offPistol models
Angle models
DIM
ENSI
ON
S
* Torque specificationsAll specified torques are measured on the Yokota testers, series YET, at a dynamic airpressure of 0.63MPa. The Yokota testers have a static transducer, the specified torques are therefore to be used as a guidance only. In general the torque range will be lower in case of using lower airpressure, extension bars, torx or hexagon inset sockets, soft joints, etc.
8 WWW.RAMI-YOKOTA.COM WWW.RAMI-YOKOTA.COM 9
Rubber protection covers for all Y-series impulse wrenches are included in the box.
Accessories for impulse wrenches on pages 18 & 19.
Y serie: Non shut-offDouble chamber air motor
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s2
Noise-leveldB(A
Y-40SA 1) 1/4" Hex 4 - 6 10.000 6 - 12 5,0 7,6 0,84 PT 1/4" 6,5 229 17 4,6 69
Y-41A 1/4" Hex 4 - 6 9.300 6 - 12 5,0 8,8 0,73 PT 1/4" 6,5 141 17 2,1 72
Y-46E 3/8" Sq. 5 - 6 8.000 16 - 30 5,8 9,6 0,87 PT 1/4" 6,5 158 18 1,0 80
Y-46A 1/4" Hex 5 - 6 8.000 16 - 26 5,8 9,6 0,87 PT 1/4" 6,5 158 18 1,0 80
Y-56E 3/8" Sq. 6 - 8 7.000 25 - 47 6,6 9,6 0,87 PT 1/4" 10 144 21 1,0 80
Y-56A 1/4" Hex 6 - 8 7.000 22 - 33 6,6 9,6 0,87 PT 1/4" 10 144 21 1,0 80
Y-61E 3/8" Sq. 6 - 8 5.500 34 - 54 6,6 8,8 0,96 PT 1/4" 10 155 21 1,0 74
Y-61A 1/4" Hex 6 - 8 5.500 27 - 41 6,6 8,8 0,96 PT 1/4" 10 155 21 1,0 74
Y-70E 3/8" Sq. 8 - 10 5.500 44 - 72 7,5 9,6 1,40 PT 1/4" 10 170 25 2,0 75
Y-90E 1/2" Sq. 10 - 12 5.000 78 - 116 8,3 15,1 1,85 PT 1/4" 10 177 30 1,5 72
Y-100E 1/2" Sq. 12 5.000 100 - 145 11,8 14,5 2,00 PT 1/4" 13 188 32,5 2,1 80
Y-130E 1/2" Sq. 14 3.500 140 - 220 12,8 18,3 2,50 PT 1/4" 13 201 34 2,2 83
Y-140 3/4" Sq. 16 3.300 160 - 270 13,1 18,4 3,20 PT 1/4" 13 226 36 3,3 82
Y-40SA
Y-100E Y-130E
Y-140 Y-70E Y-90E
Y-41A Y-46E/A Y-56E/A Y-61E/A
YX-180E YX-280E YX-380E
YX-500E YX-700E YX-900E
YX-1100E YX-1400E YX-1900E
YX-2400E YX-3000 YX-4500
YX-280C YX-500C YX-700C
B
A
B
A
AB
D
1) The Y-40SA is a straight model, all other types are pistol models.
* Torque specificationsAll specified torques are measured on the Yokota testers, series YET, at a dynamic airpressure of 0.63MPa. The Yokota testers have a static transducer, the specified torques are therefore to be used as a guidance only. In general the torque range will be lower in case of using lower airpressure, extension bars, torx or hexagon inset sockets, soft joints, etc.
DIM
ENSI
ON
S
D IMENSIONS DIMENSIONS
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread
Hosediameter
mm
DimensionsA B D
mm mm mm
Vibrationm/s2
Noise-leveldB(A)
YX-280C 3/8" 4K 4 - 6 10.000 15 - 24 5,0 7,8 1,40 PT 1/4" 6,5 257 16 50 4 83
YX-500C 3/8" 4K 6 - 8 7.500 30 - 45 5,0 8,6 1,50 PT 1/4" 6,5 266 18 66 10 73
YX-700C 3/8" 4K 8 - 10 5.000 36 - 50 5,8 10,8 1,80 PT 1/4" 6,5 289 18 70 8,6 72
www.tid-extra.hr
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread.
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s2
Noise-leveldB(A)
YX-180SE 3/8" Sq. 4 - 6 10.500 19 - 31 4,2 7,8 0,96 PT 1/4" 6,5 220 23 3,3 73
YX-180SA 1/4" Hex 4 - 6 10.500 18 - 30 4,2 7,8 0,96 PT 1/4" 6,5 220 23 3,3 73
YX-280SE 3/8" Sq. 6 - 8 10.500 25 - 38 5,0 9,1 1,02 PT 1/4" 6,5 232 23 4 73
YX-280SA 1/4" Hex 6 10.500 20 - 34 5,0 9,1 1,02 PT 1/4" 6,5 232 23 4 73
YX-380SE 3/8" Sq. 8 10.000 32 - 47 5,0 9,1 1,18 PT 1/4" 6,5 232 25,5 3,3 75
YX-380SA 1/4" Hex 6 - 8 10.000 29 - 44 5,0 9,1 1,18 PT 1/4" 6,5 232 25,5 3,3 75
YX-500SE 3/8" Sq. 8 - 10 7.500 31 - 55 5,0 11,2 1,25 PT 1/4" 6,5 241 25,5 6,6 74
YX-700SE 3/8" Sq. 8 - 10 5.000 35 - 62 5,8 13,5 1,50 PT 1/4" 6,5 262 26,5 6,6 72
YX serie: Non shut-offStraight models
* Torque specificationsAll specified torques are measured on the Yokota testers, series YET, at a dynamic airpressure of 0.63MPa. The Yokota testers have a static transducer, the specified torques are therefore to be used as a guidance only. In general the torque range will be lower in case of using lower airpressure, extension bars, torx or hexagon inset sockets, soft joints, etc.
ELR
CTR
ON
ICA
LLY
CO
NTR
OLL
ED
• Very high accuracy•Electronicallycontrolledshut-off OK/NOK LED on display• Countingfunction•Nokick-back• Maintenancefreemotor(brushless)• Lithium-ionbattery,slidingmodel• Perfectlybalanced• Compactlightweight• Lowvibrationandnoiselevels• Controllerintegrated• Pincode(passwordprotection)
Battery impulse wrenches
Accessories for impulse wrenches on pages 18 & 19.
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Weightkg
DimensionsA B
mm mm
Vibrationm/s²
Noise-leveldB(A)
YBX-50A 1/4" Hex 5 - 8 2.200 7 - 22 1,7 194 26 3 79
YBX-50E 3/8" Sq. 5 - 8 2.200 7 - 22 1,7 194 26 3 79
* Torque specificationsAll specified torques are measured on the Yokota testers, series YET, at a dynamic airpressure of 0.63MPa. The Yokota testers have a static transducer, the specified torques are therefore to be used as a guidance only. In general the torque range will be lower in case of using lower airpressure, extension bars, torx or hexagon inset sockets, soft joints, etc.
YBX-600TE in use Tightening: OK
YBX-50A/YBX-50ENon shut-off
YBX-600TE/600TAYBX-800TE/800TAElectronic controlled shut-off
TheYBX-600TandYBX-800TareElectronicallyControlledbatteryimpulse wrenches with integrated angle encoder for highly accurate torque tolerances. The shut-off is calculated over several impulses. The controller is integrated and enables counting, Poka Yoke.
WWW.RAMI-YOKOTA.COM 1110 WWW.RAMI-YOKOTA.COM
FEA
TUR
ES Y
BX
-60
0T/8
00T
YX-180SE YX-180SA YX-280SE YX-280SA YX-380SE YX-380SA
YX-700SE
YBX-600TE YBX-600TA YBX-800TE YBX-800TA
YBX-50A YBX-50E
YX-500SE
A
B
B
A
B
A
DIM
ENSI
ON
S
D IMENSIONS
DIMENSIONS
Typ Drive Boltcapacity
mm
RPM TorqueNm*
Weightkg
DimensionsA B
mm mm
Vibrationm/s2
NoiselevelsdB(A)
YBX-600TE 3/8" Sq. M6 2.000 8 - 20 1,50 170 37 < 2,5 77
YBX-600TA 1/4" Hex M6 2.000 7 - 18 1,50 170 37 < 2,5 77
YBX-800TE 3/8" Sq. M8 2.000 18 - 35 1,55 174 37 < 2,5 78
YBX-800TA 1/4" Hex M8 2.000 16 - 31 1,55 174 37 < 2,5 78
www.tid-extra.hr
Accessories for impulse wrenches on pages 18 & 19.
Poka Yoke+: functioning principleThe system is controlled by measuring the air pressure at the inlet side
of the air motor. This air pressure varies from free running to impulsing.
By this measured air pressure the controller detects contact of the bolt
head (point 2). Upon contact, the adjustable timer gives the shut-off sig-
nal (point 3). Adjustability of the timer takes care of adoption to either
hard or soft joints. Similar, the controller detects double hits and trigger
release before shut-off.
Controller YTC-3
Poka Yoke+ system
Controller YTC-3• Power supply: 100 - 240V AC
• Input:8
•Relay output: 4
opening and shutting capacity:
Max.DC-48W,AC-220VA)
•Output for solenoid valve:
1(DC24V 2W)
System features
•Group control
•Controlled shut-off
•Double tightening detection
• Interlock with assembly line
• Error judgement on trigger
release
• Teach-in mode for programming
•Oil deterioration indication
12 WWW.RAMI-YOKOTA.COM WWW.RAMI-YOKOTA.COM 13
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s²
Noise-leveldB(A)
YLa60A-JQ 1/4" Hex 6 4.000 11-20 5 5,5 0,78 PT 1/4" 6,5 130 22 1,4 71
YLa60E-JQ 3/8" Sq. 6 4.000 13 - 22 5 5,5 0,78 PT 1/4" 6,6 130 22 1,4 71
YLa70A-JQ 1/4" Hex 6 - 8 7.000 20 - 28 5,5 6,1 0,80 PT 1/4" 6,5 132 22 1,4 74
YLa70 E-JQ 3/8" Sq. 6 - 8 7.000 20 - 35 5,5 6,1 0,80 PT 1/4" 6,5 132 22 1,4 74
YLa80A-JQ 1/4" Hex 8 7.000 24 - 35 5,8 9 0,90 PT 1/4" 6,5 139 22 1,2 75
YLa80E-JQ 3/8" Sq. 8 7.000 33 - 50 5,8 9 0,90 PT 1/4" 6,5 139 22 1,2 75
YLa90E-JQ 3/8" Sq. 8 - 10 6.500 47 - 70 6,7 11,8 1,00 PT 1/4" 10 148 24 1,2 78
YLa110E-JQ 1/2" Sq. 10 - 12 6.000 65 - 105 9,6 13,1 1,40 PT 1/4" 10 164 26 1,8 81
YLa120E-JQ 1/2" Sq. 12 6.600 80 - 130 10 15,6 1,80 PT 1/4" 10 172 28 2,2 82
YLa140E-JQ 1/2" Sq. 14 6.000 100 - 160 13 18,9 2,20 PT 1/4" 10 190 30 2,4 84
YLa-JQ serie
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s²
Noise-leveldB(A)
Y-41A-JQ 1/4" Hex 4 - 6 9.300 6 - 12 5,0 8,8 0,73 PT 1/4" 6,5 141 17 2,1 72
Y-46E-JQ 3/8" Sq. 5 - 6 8.000 16 - 30 5,8 9,6 0,87 PT 1/4" 6,5 158 18 1,0 80
Y-56E-JQ 3/8" Sq. 6 - 8 7.000 25 - 47 6,6 9,6 0,87 PT 1/4" 10 144 21 1,0 80
Y-61E-JQ 3/8" Sq. 6 - 8 5.500 34 - 54 6,6 8,8 0,96 PT 1/4" 10 155 21 1,0 74
Y-70-JQ 3/8" Sq. 8 - 10 5.500 44 - 72 7,5 9,6 1,40 PT 1/4" 10 170 25 2,0 75
Y-90E-JQ 1/2" Sq. 10 - 12 5.000 78 - 116 8,3 15,1 1,85 PT 1/4" 10 177 30 1,5 72
Y-100E-JQ 1/2" Sq. 12 5.000 100 - 145 11,8 14,5 2,00 PT 1/4" 13 188 32,5 2,1 80
Y-130E-JQ 1/2" Sq. 14 3.500 140 - 220 12,8 18,3 2,50 PT 1/4" 13 201 34 2,2 83
Y-140-JQ 3/4" Sq. 16 3.300 160 - 270 13,1 18,4 3,20 PT 1/4" 13 226 36 3,3 82
Y-JQ series
* Torque specificationsAll specified torques are measured on the Yokota testers, series YET, at a dynamic airpressure of 0.63MPa. The Yokota testers have a static transducer, the specified torques are therefore to be used as a guidance only. In general the torque range will be lower in case of using lower airpressure, extension bars, torx or hexagon inset sockets, soft joints, etc.
Rubber protection covers for YLa-JQ and Y-JQ impulse wrenches are included in the box.
Y-41A-JQ Y-46E-JQ Y-56E-JQ Y-61E-JQ
YLa-110E-JQ YLa-120E-JQ YLa-140E-JQ
B
A
Lightweight YLa-JQ series
Superior clampforcesIn conventional shut-off tools point 2 is the shut-off point. Due to the
above mentioned principle of the Poka Yoke+ controller, the relaxation
is minimized and the correct torque and clampforce are achieved. The
torque is adjusted at the impulse mechanism. In combination with the
parameters in the controller YTC-3, a reliable shut-off is achieved.
The whole system is more accurate than shut-off or standard impulse wrenches.
DIM
ENSI
ON
S
YLa60A-JQ YLa60E-JQ
YLa70A-JQ YLa70E-JQ YLa80A-JQ YLa80E-JQ YLa90E-JQ
Y -70 - JQ Y-140-JQ Y-90E-JQ
Y-100E-JQ Y-130E-JQ
Start timer (at high power impulsing)
P (bar)
Free running Impulsing T (sec)
2
1 Start impulsing
3 Shut-off
www.tid-extra.hr
Electronic torque control & angle monitoring Possible errors that can be detected
Yokota system wrenches
Type Square-drive
Bolt capacity
mm
TorqueNm
RPM Weight kg
DimensionsA B
mm mm
Loadaircons.
l/s
No-loadaircons.
l/s
TKa600A 1/4" Hex 6 11 - 16 6.000 1,34 189 21,0 4,5 5,1
TKa600 3/8" 6 14 - 20 6.000 1,34 189 21,0 4,5 5,1
TKa700A 1/4" Hex 6-8 24 - 33 7.000 1,34 189 21,0 5,3 6,9
TKa700 3/8" 6-8 24 - 33 7.000 1,34 189 21,0 5,3 6,9
TKa800 3/8" 8 32 - 46 7.000 1,34 196 22,0 5,3 7,1
TKa900 3/8" 8-10 47 - 60 6.500 1,50 204 23,0 6,8 10,5
TKa1110 1/2" 10-12 65 - 95 5.500 1,97 220 25,5 8,8 13,5
TKa1400 1/2" 14 100 - 160 5.200 3,00 246 29,0 13 19
• Builtintorquesensor,directmeasurement• Builtinanglesensor• compactanglesensor,1°degreemeasurement• Torquesensornoncontactprinciple• Torque&anglecurve'sonPC• Easytorqueadjustmentonthetool• Ledoracousticindicationonthetool• Highefficiencyairmotor• Shut-offbyexternalsolenoidvalve
14 WWW.RAMI-YOKOTA.COM
Yokota Multi Fastening Controller
Yokota Japan developed the system wrench with torque controlmorethan25yearsago,inordertotightenandshut-off the impulse wrench at the target torque with the features as insufficient or over torque, error detection, bolt counting, group control, production line management, data saving etc. Due to increased market demands for accuracy and error detection, Yokota integrated the additional angle moni-toring function. By controlling the angle during the tightening process, all possible errors can be detected.
• Detectioninsufficienttorqueandovertorque• Detectionfrictioncoefficientoutoftolerances• Detectionoftoolong/tooshortbolt• Detectionofseizure• Detectionofcrossthreadedthreads• Detectionofcrookedthreads• Detectionofdamagedthreads• Detectionofdoubletightening• Detectionofblindholes
Features
YETC-210 ER Torque Control & angle monitoring
TKa600A Tka600
TKa700A TKa700 TKa1400 TKa1100
B
A
An
alys
ing
so
ftw
are
angle OK rangemax. torque
min. torquetarget torque
angle OK range
angle OK range
start torque
free running angle snug angle final angle
0
YETC-300ER2-L Torque control & angle monitoring including snug torque
tighteningOK
tighteningOK
angle OK rangemax. torque
min. torquetarget torque
angle OK rangestart torque
free running angle tightening angle
0
• Easy to program on the front
panel
• Easy to program with PC
• Torque calculation over several
impulses
• Compensation impulses to
minimize relaxation
• Poke Yoke proof, line manage-
ment
• 2 step tightening optional
• 8settingprograms
• Parallel and RS 232 connectors
standard 2-way communication
through RS 232
• Automatic program change
(sequence programmable)
• Real Time clock
• Build in timer for group control
• Various input signals selectable
• Various output signals selectable
• Statistics CP / CPK
• Memory 10.000 cycles
Advantages of the Yokota Multi Tasking Controller
DIMENSIONS
YETC-210EA
• Torque control•One channel controller• LAN version optional
YETC-210EA4
• Torque control• Four channel controller not simultaneous• LAN version optional (four I/P addresses)
YETC-210ER
• Torque control•Angle monitoring version•One channel controller• LAN version optional
YETC-320ER2L
• Torque control•Angle monitoring version• Two channel controller, two tools can be operated simultaneous• LAN standard, two IP adresses
YETC-320EA2
• Torque control• Two channel controller, two tools can be operated simultaneous
Optional:• LAN version (two I/P addresses)
Back panelOptional:• Ethernet (100 BASE-TX/10 BASA-T Autodetect function)• Protocol: TCP/IP• Connector:RJ-45
The Yokota YETC-210/320 are developed for accurate tightening and fit in a Poke Yoke assembly process. The controller controls, measures, judges, counts and documents the tightening.
TKa800 TKa900
WWW.RAMI-YOKOTA.COM 15
www.tid-extra.hr
System wrenches TKa - YED series
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm**
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s2
Noise-leveldB(A)
TKa60A 1/4" Hex 6 6.000 11 - 16 4,5 5,1 1,3 PT 1/4" 6,5 179 22 2,1 71
TKa70A 1/4" Hex 6 - 8 7.000 20 - 27 5,3 6,9 1,3 PT 1/4" 6,5 179 22 2,1 75
TKa80A 1/4" Hex 8 7.000 24 - 33 5,3 7,1 1,3 PT 1/4" 6,5 186 22 2,1 73
TKa60 3/8" Sq. 6 6.000 14 - 20 4,5 5,1 1,3 PT 1/4" 6,5 179 22 2,1 71
TKa70 3/8" Sq. 6 - 8 7.000 20 - 35 5,3 6,9 1,3 PT 1/4" 6,5 179 22 2,1 75
TKa80 3/8" Sq. 8 7.000 32 - 46 5,3 7,1 1,3 PT 1/4" 6,5 186 22 2,1 73
TKa90 3/8" Sq. 8 - 10 6.500 47 - 70 6,8 10,5 1,5 PT 1/4" 9,5 195 24 2,1 78
TKa110 1/2" Sq. 10 - 12 6.000 65 - 105 8,8 13,5 1,9 PT 1/4" 9,5 210 26 2,2 80
TKa120 1/2" Sq. 12 5.900 85 - 130 10 17,2 2,4 PT 1/4" 9,5 223 28 2,2 82
TKa140 1/2" Sq. 14 5.200 100 - 160 13 19 2,9 PT 1/4" 9,5 235 30 2,2 84
TKa150 1/2" Sq. 14 - 16 4.200 150 - 220 13,2 18,1 3,4 PT 1/4" 9,5 242 32 2,4 84
YED-200 3/4" Sq. 20 3.400 155 - 360 18,3 32,2 6,8 PT 1/2" 12,7 309 40 4,2 86
YED-240S* 1" Sq. 24 3.000 250 - 600 28,3 52,2 11,2 PT 1/2" 12,7 452 52,5 15,0 92
* YED-240S is a straight model. ** See torque specifications on page 15.
System wrenches YEX series
Type Square / Hex drive
Boltcapacity
mm
RPM TorqueNm*
Loadaircons.
l/s
No-loadaircons.
l/s
Weightkg
Inletthread
Hosediameter
mm
DimensionsA B
mm mm
Vibrationm/s²
Noise-leveldB(A)
YEX-100SA 3/8" Hex 5 8.000 4.3 - 12 3,6 4,4 1,2 PT 1/4" 9,5 285 23 3 77
YEX-120 3/8" Sq. 4 - 5 9.000 13 - 17 4,2 5 1,43 PT 1/4" 9,5 222 23 3 72
YEX-120A 1/4" Hex 4 - 5 9.000 11 - 15 4,2 5 1,43 PT 1/4" 9,5 223 23 3 72
YEX-120SA 1/4" 6 Hex 4 - 5 7.000 11 - 15 4,2 5 1,38 PT 1/4" 9,5 279 23 3 72
YEX-150 3/8" Sq. 5 - 6 9.000 19 - 27 4,2 7,8 1,43 PT 1/4" 9,5 222 23 3 72
YEX-150A 1/4" Hex 5 - 6 9.000 14 - 22 4,2 7,8 1,43 PT 1/4" 9,5 223 23 3 72
YEX-150S 3/8" Sq. 5 - 6 8.000 19 - 27 4,2 7,8 1,35 PT 1/4" 9,5 275 23 3,3 73
YEX-150SA 1/4" Hex 5 - 6 8.000 14 - 22 4,2 7,8 1,35 PT 1/4" 9,5 276 23 3,3 73
YEX-300S 3/8" Sq. 6 8.000 25 - 33 5,0 9,1 1,8 PT 1/4" 9,5 312 27 5,3 71
YEX-300SA 1/4" Hex 6 8.000 21 - 29 5,0 9,1 1,8 PT 1/4" 9,5 313 27 5,3 71
YEX-501 3/8" Sq. 6 - 8 8.200 25 - 52 5,3 9,6 2,0 PT 1/4" 9,5 234 26,5 1,6 68
YEX-501A 1/4" Hex 6 - 8 8.200 23 - 49 5,3 9,6 2,0 PT 1/4" 9,5 227 26,5 1,6 68
YEX-500S 3/8" Sq. 6 - 8 7.800 23 - 49 5,0 9,1 2,1 PT 1/4" 9,5 333 27 6,6 71
YEX-500SA 1/4" Hex 6 - 8 7.800 21 - 47 5,0 9,1 2,1 PT 1/4" 9,5 224 27 6,6 71
YEX-700S 3/8" Sq. 8 7.500 33 - 61 5,8 11,2 2,3 PT 1/4" 9,5 333 27 6,6 72
YEX-701 3/8" Sq. 8 - 10 8.000 45 - 75 6,7 13,5 2,2 PT 1/4" 9,5 246 26,5 1,6 71
YEX-901 1/2" Sq. 10 6.100 61 - 104 6,7 12,5 2,7 PT 1/4" 9,5 257 33,5 2,3 73
YEX-1400 1/2" Sq. 10 - 12 5.900 92 - 142 8,3 16,5 3,5 PT 1/4" 9,5 266 34 3 80
YEX-1900 1/2" Sq. 12 5.800 115 - 183 8,3 15,8 4,1 PT 1/4" 9,5 277 39 3 80
YEX-3000 3/4" Sq. 16 4.000 186 - 284 10,0 20,5 6,4 PT 1/4" 12,7 309 40 4 82
Note: All YEX-types are pistol models, with exception of the S and SA types.
* Torque specificationsAll specified torques are measured on the Yokota testers, series YET, at a dynamic airpressure of 0.63MPa. The Yokota testers have a static transducer, the specified torques are therefore to be used as a guidance only. In general the torque range will be lower in case of using lower airpressure, extension bars, torx or hexagon inset sockets, soft joints, etc.
For a system YEX, YED or TKa you need:1 x Controller YETC-210 GTB or YETC-210 EA1 x Impulse wrench YEX, YED or TKa1 x Solenoid valve and tool cable (7m) YETC-2 SVC
16 WWW.RAMI-YOKOTA.COM
TAIL
OR
MA
DE
IMPU
LSE
WRE
NCH
ES
YEX-120 /YEX-120A YEX-150 / YEX-150AYEX-501 / YEX-501A
YEX-701 YEX-901
YEX-1400 YEX-1900 YEX-3000
YEX -150S YEX -300S YEX -500S YEX -700S
YEX -100SA YEX -120SA YEX -150SA YEX -300SA YEX -500SA
TKa60A TKa70A TKa80A
TKa60 TKa70 TKa80 TKa90
TKa110 TKa120 TKa140 TKa150
YED-200 YED-240S
Y-61 YEX-150S
B
A
A
B
A
B
B
A
For any application, where access to the joint is difficult, we are able to provide tailor made impulse wrenches. Please send us your enquiry.
DIM
ENSI
ON
S
DIM
ENSI
ON
S
DIM
ENSI
ON
S
D IMENSIONS
WWW.RAMI-YOKOTA.COM 17
www.tid-extra.hr
Accessories
For type Ordernumber
YX-180 • YX-500 • YXS-500 • Y-40 • Y-61 • Y-T45 Y-T55 • YEF-45 • YEF-55 • YEX-120 YEX-150 • YED-60
SKK
YX-500S • YX-1400 • YXS-700 • YXS-1100 • Y-70 Y-90 • Y-130 • Y-T70 • Y-T90 • YEF-70 • YEF-90 YEX-300 • YEX-1400 • YBX-50
SK / SKN
Charger for YBX-600T/800TFor type Ordernumber Description
YBX-600TYBX-600TAYBX-800TYBX-800TA
7679-0000-01-00 100 - 240 V, Type BC200Charging time: 20 minutes
Battery for YBX-600T/800TFor type Ordernumber Description
YBX-600TYBX-600TAYBX-800TYBX-800TA
0351-1521-03-99 22,2 V / 1,5 Ah Li-ion, Type BL 22charging time: 20 minutes
- 0351-0029-00-01 Rubber protection cover for battery
Battery for YBX-50For type Ordernumber Description
YBX-1YBX-50
8530-3001-00-01 9,6 V / 2,0 Ah, Type EB-9B, Ni-Cd
Charger for YBX-50For type Ordernumber Description
YBX-1YBX-50
8530-4006-00-00 230 Volt, Type UC24YFAUniversal charger
Accessories
Battery and charger for battery impulse wrenches
Double spiral hose1 for air & 1 for tool cable
Tool holder
Service sets Yokota torque measuringequipment
Service sets containing:O-rings, back-up rings and springs for impulse mecha-nisms required for oil change.
Service setsYou will need these service sets with spare parts if you are going to change the oil. For quick service we advise you to use a vacuum pump (YEVP-1*) and oil tank (YEVP-1T*)
Please note!Always use oil with the right specifications when changing oil. Only then you will have a optimal tool power and a minimum oil consumption. We recommend NOBP oil for the impulse unit.
For type Ordernumber
TKa-60 0186-0991-00-99
TKa-600 0186-0991-00-99
TKa-70 0186-0991-00-99
TKa-700 0186-0991-00-99
TKa-80 0193-0991-00-99
TKa-90 0181-0991-00-99
TKa-900 0181-0991-00-99
TKa-110 0187-0991-00-99
TKa-1110 0187-0991-00-99
TKa-120 0342-0991-00-99
TKa-140 0341-0991-00-99
TKa-1400 0341-0991-00-99
TKa-150 0343-0991-00-99
For type Ordernumber
Y-41 0095-0991-00-99
Y-46 0273-0991-01-99
Y-56 0259-0991-01-99
Y-61 0158-0991-01-99
Y-70 0158-0991-03-99
Y-90 0141-0991-00-99
Y-100 0334-0991-01-99
Y-130 0335-0991-00-99
Y-140 0412-0991-02-09
YLa70 0189-0991-00-99
YLa80 0191-0991-00-99
YLa90 0188-0991-00-99
YLa110 0190-0991-00-99
YLa120 0345-0991-00-99
YLa140 0346-0991-00-99
YLT60 0371-0991-00-99
YLT70 0372-0991-00-99
YLT80 0373-0991-00-99
YLT110 0379-0991-00-99
YLT120 0380-0991-00-99
YLT140 0381-0991-00-99
YBX-1 0259-0991-01-99
YBX-50 0259-0991-01-99
YBX-600T 0189-0991-00-99
YBX-800T 0191-0991-00-99
YED-200 0409-0991-00-99
YED-240S 0411-0991-01-99
YEX-120 0089-0991-01-99
YEX-150 0089-0991-01-99
YEX-300S 0086-0991-01-99
YEX-500S 0077-0991-02-99
Yokota torque measuring equip-ment (YET-series) is especially designed to check and test the functioning and performance of impulse wrenches. All specified torque figures in this brochure are measured on a Yokota torque test-er (YET series), with 0,63 MPa air pressure (dynamic). This is a static torque tester. Torque values may differ with other measuring equip-ment and/or joints (hard/soft).
Service sets containing: O-rings, back up rings and springs for impulse mechanisms for oilchange.
For type Range
YET-501C 5 - 50 Nm
YET-2001C 20 - 200 Nm
YET-5001C 100 - 500 Nm
18 WWW.RAMI-YOKOTA.COM WWW.RAMI-YOKOTA.COM 19
Toolcable for system wrenches
For the YETC-210ER, YETC-300R2-LToolcable Ordernumber
10 meter (included with YETC-210ER) 7681-0908 00 03
10 meter extension cable 7681-0908 00 06
Rubber protection cover for impulse- & system wrenchesFor type Ordernumber
YX-180 0089-0029-00-00
YX-280 0081-0029-00-00
YX-380 0086-0029-00-00
YX-500 0077-0029-00-01
YX-700 0129-0029-00-01
YX-900 0237-0029-00-01
YX-1100 0241-0029-00-00
YX-1400 0322-0029-00-00
YX-1900 0320-0029-00-01
YX-2400 0406-0029-00-01
YX-3000 0405-0029-00-00
For type Ordernumber
TKa60 0186-0029-00-00
TKa70 0186-0029-00-00
TKa80 0193-0029-00-00
TKa90 0181-0029-00-00
TKa110 0187-0029-00-00
TKa120 0342-0029-00-00
TKa140 0341-0029-00-00
TKa150 0343-0029-00-00
TKa600 0358-0029-00-00
TKa700 0358-0029-00-00
TKa900 0355-0029-00-00
TKa1110 0356-0029-00-00
TKa1400 0357-0029-00-00
For type Ordernumber
YLa70 0189-0029-00-00
YLa80 0191-0029-00-00
YLa90 0188-0029-00-00
YLa110 0190-0029-00-00
YLa120 0345-0029-00-00
YLa140 0346-0029-00-00
YLT60 0371-0029-00-00
YLT70 0372-0029-00-00
YLT80 0373-0029-00-00
YLT110 0379-0029-00-00
YLT120 0380-0029-00-00
YLT140 0381-0029-00-00
YLT150 0382-0029-00-00
For type Ordernumber
Y-41 0161-0029-00-00
Y-46 0160-0029-00-00
Y-56 0159-0029-00-00
Y-61 0158-0029-00-00
Y-70 0135-0029-00-00
Y-90 0141-0029-00-00
Y-100 0334-0029-00-00
Y-130 0335-0029-00-00
Y-140 0412-0029-00-00
Y-T40 0169-0029-00-00
Y-T45 0164-0029-00-00
Y-T55 0164-0029-00-00
Y-T70 0166-0029-00-00
Y-T90 0167-0029-00-00
For type Ordernumber
YBX-600T 0351-0029-00-00
YBX-800T 0352-0029-00-00
YED-200 0409-0029-00-00
YEX-120 0093-0029-00-00
YEX-150 0093-0029-00-00
YEX-501 0260-0029-00-00
YEX-701 0143-0029-00-00
YEX-901 0261-0029-00-00
YEX-1400 0323-0029-00-00
YEX-1900 0321-0029-00-00
YEX-3000 0407-0029-00-00
For the YETC-210 EA, YETC-210 EA4C, YETC-300 EAToolcable Ordernumber
7 meter 7642 - 1371-00-00
10 meter 7642 - 1400-00-00
12 meter 7642 - 1600-00-00
15 meter 7642 - 1908-01-19
Connection cable, 50 cm 7642 - 0908-01-38
Valves for system wrenches
Joint Assy for YTC-3 controller
For all controller (2 Step valve set)
For type Ordernumber
Joint Assy for 3/8 tools 7671-0077-00-97
Joint assy for 1/4 large tools 7671-0077-00-98
Joint assy for 1/4 standard tools 7671-0077-00-99
3/8" YETC - 2 SVD 3/8 - -
1/2" YETC - 2SVD 1/2 - -
For type Ordernumber
YEX-701 0143-0991-00-99
YEX-901 0237-0991-01-99
YEX-1400 0323-0991-00-99
YEX-1900 0320-0991-00-99
YEX-3000 0405-0991-00-99
YX-80 0095-0991-00-99
YX-180 0089-0991-01-99
YX-280 0089-0991-01-99
YX-380 0086-0991-01-99
YX-500S (C) 0086-0991-01-99
YX-500 0077-0991-02-99
YX-700 (S) 0129-0991-00-99
YX-700C 0281-0991-01-99
YX-900 0237-0991-01-99
YX-1100 0237-0991-01-99
YX-1400 0322-0991-00-99
YX-1900 0320-0991-00-99
YX-2400 0320-0991-00-99
YX-3000 0405-0991-00-99
YX-4500 0722-0991-00-99
YXS-500 0245-0991-00-99
YXS-700 0246-0991-00-99
YXS-900 0243-0991-01-99
YXS-1100 0243-0991-01-99
YXS-1900 0248-0991-00-99
For type Ordernumber
For all system wrenches -MISCO10606
www.tid-extra.hr
20 WWW.RAMI-YOKOTA.COM
Sleeve drive sockets
1 2 1 4
5
2
3
3
1
3/8" Drive
SIZE
6-Point long magnetic Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO6091P006 6 D 11 19 100 3DO6091P007 7 D 12 19 100 3DO6091P008 8 D 13 19 100 4DO6091P009 9 D 15 19 100 4DO6091P010 10 D 16 19 100 4DO6091P011 11 D 17,5 19 100 5DO6091P012 12 D 18,5 19 100 5DO6091P013 13 D 20 22 100 6DO6091P014 14 D 21 22 100 6DO6091P015 15 D 22 22 100 7DO6091P016 16 D 24 22 100 7DO6091P017 17 D 25 22 100 7DO6091R006 6 D 11 19 150 3DO6091R007 7 D 12 19 150 3DO6091R008 8 D 13 19 150 4DO6091R009 9 D 15 19 150 4DO6091R010 10 D 16 19 150 4DO6091R011 11 D 17,5 19 150 5DO6091R012 12 D 18,5 19 150 5DO6091R013 13 D 20 22 150 6DO6091R014 14 D 21 22 150 6
1
2
3
DRWG D
SIZE
6-Point normal Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO60910006 6 A 11 19 43 5DO60910007 7 A 12 19 43 5DO60910008 8 A 13 19 43 7DO60910009 9 A 15 19 43 7DO60910010 10 A 16 19 43 8DO60910011 11 A 17,5 19 43 9DO60910012 12 B 19 19 43 9DO60910013 13 A 20 22 43 9DO60910014 14 A 21 22 43 9DO60910015 15 B 22 22 43 11DO60910016 16 C 24 22 43 11DO60910017 17 C 25 22 43 11DO60910018 18 C 26 22 43 11DO60910019 19 C 27,5 22 43 11DO60910021 21 C 30 22 43 13
SIZE
6-Point normal magnetic Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO6091A006 6 A 11 19 43 5DO6091A007 7 A 12 19 43 5DO6091A008 8 A 13 19 43 7DO6091A009 9 A 15 19 43 7DO6091A010 10 A 16 19 43 8DO6091A011 11 A 17,5 19 43 9DO6091A012 12 B 18,5 19 43 9DO6091A013 13 A 20 22 43 9DO6091A014 14 A 21 22 43 9DO6091A015 15 B 22 22 43 11DO6091A016 16 C 24 22 43 11DO6091A017 17 C 25 22 43 11DO6091A018 18 C 26 22 43 11DO6091A019 19 C 27 22 43 11DO6091A020 20 C 28 22 43 13DO6091A021 21 C 30 22 43 13DO6091A022 22 C 31 22 50 13DO6091A023 23 C 32 22 50 13DO6091A024 24 C 34 22 50 13DO6091A025 25 C 35 22 50 13DO6091A026 26 C 36 22 50 13DO6091A027 27 C 38 22 50 13
DRWG CDRWG A DRWG B
SIZE
6-Point long Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO60913006 6 D 10,5 22 100 4DO60913008 8 D 12,5 22 100 8DO60913010 10 D 15 22 100 8DO60913012 12 D 18 22 100 9DO60913013 13 D 19 22 100 9DO60913014 14 D 20 22 100 9DO60913015 15 D 21 22 100 11DO60913016 16 D 22,5 22 100 11DO60913017 17 D 24 22 100 11DO60914006 6 D 10,5 22 150 4DO60914008 8 D 12,5 22 150 8DO60914010 10 D 15 22 150 8DO60914012 12 D 18 22 150 9DO60914013 13 D 19 22 150 9DO60914014 14 D 20 22 150 9DO60914015 15 D 21 22 150 11DO60914016 16 D 22,5 22 150 11DO60914017 17 D 24 22 150 11DO60915006 6 D 10,5 22 200 4DO60915008 8 D 12,5 22 200 8DO60915010 10 D 15 22 200 8DO60915012 12 D 18 22 200 9DO60915013 13 D 19 22 200 9DO60915014 14 D 20 22 200 9DO60915015 15 D 21 22 200 11DO60915016 16 D 22,5 22 200 11DO60915017 17 D 24 22 200 11
Sleeve drive sockets3/8" Drive
SIZE
Torx® extern Type A/F DRWG D1
mmD2mm
Lmm
L2mm
DO66910005 E5 A 8 19 43 4,5DO66910006 E6 A 9 19 43 5DO66910007 E7 A 9,5 19 43 6DO66910008 E8 A 11 19 43 6,5DO66910010 E10 A 13 19 43 7,5DO66910011 E11 A 14 19 43 8DO66910012 E12 A 15,5 19 43 8,5DO66910014 E14 A 17,5 22 43 10DO66910016 E16 A 18,5 22 43 11
Torx® is a trademark of Textron.
SIZE
Hex Driver (Inbus) Type A/F
mmDRWG L1
mmD2mm
Lmm -
MetricalDO68916003 3 F 11 22 75 -DO68916004 4 F 11 22 75 -DO68916005 5 F 11 22 75 -DO68916006 6 F 11 22 75 -DO68916007 7 F 16 22 75 -DO68916008 8 F 16 22 75 -DO68916009 9 F 16 22 75 -DO68916010 10 F 16 22 75 -DO68916011 11 F 16 22 75 -DO68916012 12 F 16 22 75 -DO68916013 13 F 16 22 75 -DO68916014 14 F 16 22 75 -DO68916015 15 F 16 22 75 -DO68916016 16 F 16 22 75 -
1
2
3
4
5
Stud Bolt Setters Type Size D1
mmD2mm
Lmm
DO66A10062 M6 x 1 12,5 22 50DO66A10083 M8 x 1,25 15 22 50DO66A10104 M10 x 1,5 17 22 50
SIZE
6-Point long magnetic (continued) Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO6091R015 15 D 22 22 150 7DO6091R016 16 D 24 22 150 7DO6091R017 17 D 25 22 150 7DO6091T007 7 D 12 19 200 3DO6091T008 8 D 13 19 200 4DO6091T009 9 D 15 19 200 4DO6091T010 10 D 16 19 200 4DO6091T011 11 D 17,5 19 200 5DO6091T012 12 D 18,5 19 200 5DO6091T013 13 D 20 22 200 6DO6091T014 14 D 21 22 200 6DO6091T015 15 D 22 22 200 7DO6091T016 16 D 24 22 200 7DO6091T017 17 D 25 22 200 7
SIZE
6-Point deep magnetic Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO6091Q010 10 A 16,0 19 100 5DO6091Q012 12 A 18,5 19 100 6DO6091Q013 13 A 20,0 22 100 6DO6091Q014 14 A 21,0 22 100 6DO6091Q016 16 A 24,0 22 100 7
SIZE
Torx® intern Type A/F DRWG L1
mmD2mm
Lmm -
DO68811009 T9 F 2,0 22 75 -DO68811010 T10 F 2,8 22 75 -DO68811015 T15 F 2,8 22 75 -DO68811020 T20 F 2,8 22 75 -DO68811025 T25 F 3,0 22 75 -DO68811027 T27 F 3,0 22 75 -DO68811030 T30 F 3,8 22 75 -DO68811040 T40 F 3,8 22 75 -DO68811045 T45 F 4,3 22 75 -DO68811047 T47 F 5,0 22 75 -DO68811050 T50 F 5,0 22 75 -DO68811055 T55 F 5,0 22 75 -
Torx® is a trademark of Textron.
DRWG DDRWG A DRWG F
WWW.RAMI-YOKOTA.COM 21
www.tid-extra.hr
Sleeve drive sockets1/2" Drive
1
2
3
DRWG DDRWG CDRWG A DRWG B
Sleeve drive sockets1/2" Drive
1
2
4
3
5
Stud Bolt Setters Type Size D1
mmD2mm
Lmm
DO66A21062 M6 x 1 13 25 75DO66A21083 M8 x 1,25 15 25 75DO66A21104 M10 x 1,5 17 25 75DO66A21125 M12 x 1,75 19 25 75DO66A21146 M14 x 2 22 25 75DO66A21166 M16 x 2 27 30 75
22 WWW.RAMI-YOKOTA.COM
2
1 1 4
5
2
3
3
SIZE
6-Point long magnetic Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO6092P010 10 D 17,5 25 100 4DO6092P011 11 D 18,5 25 100 5DO6092P012 12 D 20 25 100 5DO6092P013 13 D 21 25 100 6DO6092P014 14 D 22,5 25 100 6DO6092P015 15 D 23,5 30 100 7DO6092P016 16 D 25 30 100 7DO6092P017 17 D 26 30 100 7DO6092P018 18 D 27,5 30 100 8DO6092P019 19 D 28,5 30 100 8
DO6092R010 10 D 17,5 25 150 12DO6092R011 11 D 18,5 25 150 12DO6092R012 12 D 20 25 150 12DO6092R013 13 D 21 25 150 12DO6092R014 14 D 22,5 25 150 12DO6092R015 15 D 23,5 30 150 12DO6092R016 16 D 25 30 150 13DO6092R017 17 D 26 30 150 13DO6092R018 18 D 27,5 30 150 13DO6092R019 19 D 28,5 30 150 13
DO6092T010 10 D 17,5 25 200 12DO6092T011 11 D 18,5 25 200 12DO6092T012 12 D 20 25 200 12DO6092T013 13 D 21 25 200 12DO6092T014 14 D 22,5 25 200 12DO6092T015 15 D 23,5 30 200 12DO6092T016 16 D 25 30 200 13DO6092T017 17 D 26 30 200 13DO6092T018 18 D 27,5 30 200 13DO6092T019 19 D 28,5 30 200 13
SIZE
6-Point normal Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO60920012 12 A 20 25 52 12DO60920013 13 A 21 25 52 12DO60920014 14 A 22,5 25 52 12DO60920015 15 A 23,7 30 52 12DO60920016 16 A 25 30 52 12DO60920017 17 A 26 30 52 12DO60920018 18 A 27,5 30 52 12DO60920019 19 A 28,7 30 52 12DO60920021 21 B 30 30 52 12DO60920022 22 C 32 30 52 12DO60920023 23 C 32 30 52 12DO60920024 24 C 35 30 52 12DO60920025 25 C 36 30 57 12DO60920027 27 C 39 30 57 12DO60920030 30 C 42 30 62 12DO60920032 32 C 44 30 62 12
SIZE
6-Point long Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
Metrical
DO60923010 10 D 17 25 100 12DO60923012 12 D 19,5 25 100 12DO60923013 13 D 20,5 25 100 12DO60923014 14 D 21,5 25 100 12DO60923015 15 D 22,5 25 100 12DO60923017 17 D 25 25 100 13DO60923019 19 D 28 25 100 13
DO60924010 10 D 17 25 150 12DO60924012 12 D 19,5 25 150 12DO60924013 13 D 20,5 25 150 12DO60924014 14 D 21,5 25 150 12DO60924015 15 D 22,5 25 150 12DO60924017 17 D 25 25 150 13DO60924019 19 D 28 25 150 13
DO60925010 10 D 17 25 200 12DO60925012 12 D 19,5 25 200 12DO60925013 13 D 20,5 25 200 12DO60925014 14 D 21,5 25 200 12DO60925015 15 D 22,5 25 200 12DO60925017 17 D 25 25 200 13DO60925019 19 D 28 25 200 13
WWW.RAMI-YOKOTA.COM 23
SIZE
6-Point normal magnetic Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO6092A006 6 A 13 25 52 5DO6092A007 7 A 14 25 52 5DO6092A008 8 A 15 25 52 7DO6092A009 9 A 16 25 52 7DO6092A010 10 A 17,5 25 52 8DO6092A011 11 A 18,5 25 52 9DO6092A012 12 A 20 25 52 12DO6092A013 13 A 21 25 52 12DO6092A014 14 A 22,5 25 52 12DO6092A015 15 A 23,5 30 52 12DO6092A016 16 A 25 30 52 12DO6092A017 17 A 26 30 52 12DO6092A018 18 A 27,5 30 52 12DO6092A019 19 A 28,5 30 52 12DO6092A020 20 B 30 30 52 12DO6092A021 21 C 31 30 52 12DO6092A022 22 C 32 30 52 12DO6092A023 23 C 34 30 52 12DO6092A024 24 C 35 30 52 12DO6092A025 25 C 36 30 57 12DO6092A026 26 C 38 30 57 12DO6092A027 27 C 38,5 30 57 12
SIZE
6-Point deep magnetic Type A/F
mmDRWG D1
mmD2mm
Lmm
L1mm
MetricalDO6092Q010 10 A 17,5 25 100 5DO6092Q013 13 A 21,0 25 100 6DO6092Q016 16 A 25,0 30 100 7DO6092Q017 17 A 26,0 30 100 7DO6092Q019 19 A 28,5 30 100 8
SIZE
Torx® internal Type A/F DRWG L1
mmD2mm
Lmm -
DO68821020 T20 F 2,8 25 75 -DO68821025 T25 F 3,0 25 75 -DO68821027 T27 F 3,0 25 75 -DO68821030 T30 F 3,8 25 75 -DO68821040 T40 F 3,8 25 75 -DO68821045 T45 F 4,3 25 75 -DO68821047 T47 F 5,0 25 75 -DO68821050 T50 F 5,0 25 75 -DO68821055 T55 F 5,5 25 75 -DO68821060 T60 F 8,0 25 75 -DO68821070 T70 F 9,4 25 75 -DO68821080 T80 F 10,5 25 75 -DO68821090 T90 F 11,8 25 75 -DO68821100 T100 F 13,1 25 75 -
Torx® is a trademark of Textron.
SIZE
Hex Driver 6-Point (Inbus) Type A/F
mmDRWG L1
mmD2mm
Lmm -
MetricalDO68925003 3 F 11 25 75 -DO68925004 4 F 11 25 75 -DO68925005 5 F 15 25 75 -DO68925006 6 F 15 25 75 -DO68925007 7 F 20 25 75 -DO68925008 8 F 25 25 75 -DO68925009 9 F 25 25 75 -DO68925010 10 F 25 25 75 -DO68925011 11 F 25 25 75 -DO68925012 12 F 25 25 75 -DO68925013 13 F 25 25 75 -DO68925014 14 F 25 25 75 -DO68925015 15 F 25 25 75 -DO68925016 16 F 25 25 75 -DO68925017 17 F 25 25 75 -DO68925018 18 F 25 25 75 -DO68925019 19 F 25 25 75 -
SIZE
Torx® external Type A/F DRWG D1
mmD2mm
Lmm
L2mm
DO66920010 E10 A 14 25 52 7,5DO66920011 E11 A 15 25 52 8DO66920012 E12 A 16 25 52 8,5DO66920014 E14 A 18 25 52 10DO66920016 E16 A 20 25 52 11DO66920018 E18 A 22 25 52 12,5DO66920020 E20 A 25 30 52 14DO66920022 E22 A 27 30 52 15DO66920024 E24 A 29 30 52 16,5
Torx® is a trademark of Textron.
www.tid-extra.hr
Sleeve drive sockets3/4" Drive
1
2
3
4
5
DRWG F
DRWG CDRWG A DRWG B
Extensions
Type Square-drive
Lmm
D2mm
Metrical
DO64614075 3/8" 75 22DO64614125 3/8" 125 22DO64614250 3/8" 250 22DO64624075 1/2" 75 25DO64624125 1/2" 125 25DO64624175 1/2" 175 25DO64624250 1/2" 250 25DO64644175 3/4" 175 44DO64644250 3/4" 250 44DO64644330 3/4" 330 44
5
Sleeve drive socketsAdaptors
1
2
Action sleeve drive power sockets guarantee reduced vibration!
Action sleeve drive power sockets are supported with an O-ring on the axle of theimpulse wrench, giving a tighter fit on the tool.
Sleeve drive power sockets guarantee:• Torque improvement•Reduced vibration•Reduced noise level•Reduced wear
1 1 23
4
2
SIZE
6-Point normal Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
MetricalDO60940017 17 A 31 44 65 12DO60940018 18 A 32 44 65 12DO60940019 19 A 33 44 65 14DO60940021 21 A 35 44 65 16DO60940022 22 A 37 44 65 16DO60940023 23 A 38 44 65 16DO60940024 24 A 39 44 65 16DO60940026 26 A 41 44 65 16DO60940027 27 A 43 44 65 16DO60940028 28 B 44 44 68 20DO60940029 29 C 45 44 68 20DO60940030 30 C 47 44 68 20DO60940032 32 C 49 44 70 20DO60940033 33 C 51 44 70 20DO60940034 34 C 52 44 70 20DO60940035 35 C 53 44 70 20DO60940036 36 C 54 44 70 20DO60940038 38 C 57 44 72 22DO60940041 41 C 60 44 72 22DO60940046 46 C 67 54 77 23DO60940050 50 C 71 54 77 23
SIZE
6-Point magnetic Type A/F
mmDRWG D1
mmD2mm
Lmm
L2mm
Metrical
DO6094A013 13 A 24,5 44 65 12DO6094A014 14 A 25,5 44 65 12DO6094A015 15 A 27 44 65 12DO6094A016 16 A 28 44 65 12DO6094A017 17 A 30 44 65 12DO6094A018 18 A 31 44 65 12DO6094A019 19 A 32 44 65 14DO6094A020 20 A 34 44 68 14DO6094A021 21 A 35 44 68 16DO6094A022 22 A 37 44 68 16DO6094A023 23 A 38 44 68 16DO6094A024 24 A 39 44 68 16DO6094A025 25 A 41 44 69 16DO6094A026 26 A 42 44 69 16DO6094A027 27 A 43 44 69 16
SIZE
Hex Driver 6-Point (Inbus) Type A/F
mmDRWG D2
mmLmm
L2mm
-
Metrical
DO68945010 10 F 44 100 20 -DO68945012 12 F 44 100 20 -DO68945014 14 F 44 100 20 -DO68945016 16 F 44 100 20 -DO68945017 17 F 44 100 20 -DO68945019 19 F 44 100 20 -DO68945022 22 F 44 100 20 -DO68945024 24 F 44 100 20 -DO68945027 27 F 44 100 20 -DO68945030 30 F 44 100 20 -DO68945032 32 F 44 100 20 -DO68945033 33 F 44 100 20 -DO68945036 36 F 44 100 20 -DO68945038 38 F 44 100 20 -
SIZE
Torx® external Type A/F DRWG D1
mmD2mm
Lmm
L2mm
MetricalDO66940018 E18 A 26 44 65 12,5DO66940020 E20 A 28 44 65 14DO66940022 E22 A 31 44 65 15DO66940024 E24 A 33 44 65 16,5
Torx® ist eine Handelsmarke von Textron.
SIZE
Quickchange adaptors Type Drive-
inDrive-out
D2mm
Lmm - -
MetricalDO69151116 3/8" 1/2" 20 80 - -DO69152112 1/2" 3/8" 25 75 - -DO69154116 3/4" 1/2" 44 90 - -DO69151112 3/8" 3/8" 19 75 - -DO69151212 3/8" 3/8" 19 100 - -DO69152216 1/2" 1/2" 25 100 - -DO69154324 3/4" 3/4" 44 125 - -
SIZE
Quickchange adaptors Type Square-
driveHex chuck
D2mm
Lmm - -
MetricalDO69111E08 3/8" 1/4" 52 22 - -DO69111E14 3/8" 7/16" 62 22 - -DO69112E08 1/2" 1/4" 60 25 - -DO69112E14 1/2" 7/16" 70 25 - -DO69114E14 3/4" 7/16" 80 44 - -
24 WWW.RAMI-YOKOTA.COM WWW.RAMI-YOKOTA.COM 25
www.tid-extra.hr
26 WWW.RAMI-YOKOTA.COM
Type Brand Capacitykg
Cable length
m
Gewichtkg
Hose-diameter
mm
Aircons.l/min
Inlet-thread
RRI-9001/1 RRI 0,5 - 1,5 2,0 0,5 - - -
RRI-9003/1 RRI 1,0 - 3,0 2,0 0,7 - - -
RRI-9005/1 RRI 2,5 - 5,0 2,0 0,9 - - -
EK-00 RRI 0,5 - 1,5 0,5 0,2 - - -
EK-0 RRI 0,5 - 1,5 1,0 0,5 - - -
TW-3 RRI 1,0 - 3,0 1,3 1,4 - - -
TW-5 RRI 2,5 - 5,0 1,3 1,5 - - -
TW-9 RRI 4,5 - 9,0 1,3 3,4 - - -
TW-15 RRI 9 -15 1,3 3,8 - - -
HTB-0 RRI 0,5 - 1,5 1,3 1,58 6,5 700 PT 1/4"
HTB-1 RRI 1,5 - 3,0 1,3 1,66 6,5 700 PT 1/4"
HTB-2 RRI 3,0 - 5,0 1,3 1,73 6,5 700 PT 1/4"
Long strokeType Brand Capacity
kgCable length
mWeight
kg- -
ELF-3 RRI 1,5 - 3,0 2,5 4,1 - -
ELF-5 RRI 3 - 5,0 2,5 4,2 - -
ELF-9 RRI 5 - 9 2,5 4,7 - -
ELF-15 RRI 9 - 15 2,5 10,0 - -
HTB-0HTB-1HTB-2
Hosereel with integrated cable
(Spring) balancersStandard model
RRI-9001/1RRI-9003/1RRI-9005/1
EK-00EK-0
TW-3 TW-5
TW-9 TW-15
ELF-3ELF-5ELF-9
ELF-15
IMPACT SOCKETS FOR OPTIMAL PERFORMANCE AND SECURITY
www.rami-yokota.com
Impact socketsand accessories
Normal / Long
Magnetic/ Torx®
Hex Head
12-Point
Surface Drive
Thin Wall
Triple Square / Ribe
Universal Joint
Sleeve Drive
Impact Sockets Sets
Torque / Adaptors
Extension Bars
ACTION Action brochureImpact sockets for optimal performance and security
Available in the following languages:English, German, French
CONTENT:Impact sockets and accessories, Normal / Long, Magnetic / Torx®, Hex Head / 12-Point,Surface Drive / Thin wall, Universal joints, Sleeve drive, Impact Socket Sets,Torque / Adapters, Extension Bars
(Spring) balancers & SpecialsImpact sockets for screwdrivers
DRWG D
1/4" Drive
1
2
3
Application example
1 3
2
2
SIZE
6-Kant Type A/F
mmDRWG D1
mmLmm
L1mm
-
MetricalDO697B0S04 4 A 8 55 4,5 -DO697B0S06 6 A 10 55 4,5 -DO697B0T06 6 A 10 75 4,5 -DO697B0T07 7 A 11 75 4,5 -DO697B0T08 8 A 12 75 4,5 -DO697B0T10 10 A 14 75 5,5 -DO697B0T12 12 A 17 75 5,5 -DO697B0T13 13 A 18 75 5,5 -DO697B0T14 14 A 19 75 5,5 -
SIZE
6-Point magnetic Type A/F
mmDRWG D1
mmLmm
L1mm
-
MetricalDO697B0M06 6 B 10 55 4,5 -DO697B0M08 8 B 12 55 4,5 -DO697B0M10 10 B 14 55 5,5 -DO697B0M12 12 B 17 55 5,5 -DO697B0M13 13 B 18 55 5,5 -DO697B0M14 14 B 19 55 5,5 -DO697B0P06 6 B 10 100 4,5 -DO697B0P08 8 B 12 100 4,5 -DO697B0P10 10 B 14 100 5,5 -DO697B0P12 12 B 17 100 5,5 -DO697B0P13 13 B 18 100 5,5 -DO697B0P14 14 B 19 100 5,5 -
SIZE
6-Point deep magnetic Type A/F
mmDRWG D1
mmLmm
L1mm
-
MetricalDO697B7006 6 C 10 100 4,5 -DO697B7008 8 C 12 100 4,5 -DO697B7010 10 C 14 100 5,5 -DO697B7012 12 C 17 100 5,5 -DO697B7013 13 C 18 100 5,5 -DO697B7014 14 C 19 100 5,5 -DO697B9006 6 C 10 200 4,5 -DO697B9008 8 C 12 200 4,5 -DO697B9010 10 C 14 200 5,5 -DO697B9012 12 C 17 200 5,5 -DO697B9013 13 C 18 200 5,5 -DO697B7014 14 C 19 200 5,5 -
SIZE
Tap holding sockets Type A
mmDRWG Ø d
mmØ Dmm
Lmm
-
MetricalDO63A65001 3,4 D 4,5 14 55 -DO63A65002 4,9 D 6,0 15 55 -DO63A65003 5,5 D 7,0 16 55 -DO63A65004 6,2 D 8,0 17 60 -DO63A65005 7,0 D 9,0 18 70 -DO63A65006 8,0 D 10,0 19 70 -DO63A65007 9,0 D 11,0 20 70 -DO63A65008 9,0 D 12,0 21 70 -DO63A65009 11,0 D 14,0 23 75 -
DRWG A DRWG B DRWG C
WWW.RAMI-YOKOTA.COM 27
www.tid-extra.hr