Upload
phamnguyet
View
257
Download
8
Embed Size (px)
Citation preview
Communication Systems, 5e
Chapter 6: Sampling and pulse modulation
A. Bruce CarlsonPaul B. Crilly
2
Pop Quiz1) To accurately reconstruct a baseband signal from its
samples, we must sample at a frequency at least _____ times higher than the highest frequency in the signal.
a) two b) three c) four
2) It is possible to reconstruct a narrowband signal by sampling at less than the Nyquist rate.
a) TRUE b) FALSE
3
Pop Quiz1) To accurately reconstruct a baseband signal from its
samples, we must sample at a frequency at least _____ times higher than the highest frequency in the signal.
a) two b) three c) four
2) It is possible to reconstruct a narrowband by sampling at less than the Nyquist rate.
a) TRUE b) FALSE
4
Chapter 6: Sampling and pulse modulation
Sampling theory and practice
Pulse-amplitude modulation
Pulse-time modulation
5
Sampling theory and practice
6
Practical sampling and reconstruction
Real samplers have finite duration pulses (e.g.
chopper sampling)
Practical reconstruction filters are not ideal
Sampled signals are time limited ⇒ not bandlimited
⇒ cannot avoid some aliasing
7
Non-ideal sampling
As seen earlier, no loss of info with non-impulse
sampling
Non-ideal LPF reconstruction can be overcome by
prefiltering the original message ⇒ equalization
We can minimize aliasing by band limiting the input
signal ⇒ anti-alias LPF
8
Practical reconstruction filter
9
Reconstruction using a zero order hold (ZOH) interpolation
y(t)=∑k
x (k T S)∏ [ t−k T S−T S /2
T S ]⇒ reconstruction filter
⇒∣H ZOH( f )∣ = ∣T S sinc( f T S)∣
10
Reconstruction using a first order hold (FOH) interpolation
y(t)=∑k
x (k T S)Λ[ t−k T S−T S /2
T S ]⇒ reconstruction filter
⇒∣H FOH( f )∣=∣T S √1+(2π f T S)2sinc2
( f T S)∣
11
Signal reconstruction from sampled signal (a) ZOH (b) FOH
12
Signal Reconstruction
H FOH f and H ZOH f are low pass filter functions,but they are not ideal LPFs.The difference in frequency response between an idealLPF and the ZOH or FOH introduces aperture errors inthe reconstruction process.These aperture errors can be compensated by prefilteringthe data to emphasize the higher frequencies.Prefiltering⇒equalization
13
RC anti-alias filter
1. Time limited signals have large bandwidth⇒ to reduce errors due to aliased componentsspilling over into the message bandpass weincorporate an anti-aliasing filter.
2. Anti-aliasing filter often implemented via
an RC LPF with B=1
2 RC3. Because RC LPFs do not have sharp cutoff ⇒ BW
⇒oversample the message signal .
14
Message spectrum (a) output of RC filter, (b) after sampling
(a) Original message spectrum, (b) spectrum after sampling
15
Assuming a first order LPF is usedthe maximum aliasing error is
Error%= 1/0.707
1 f a /B2
with B=1
2 RC, f a= f S−B
16
Oversampling
If a signal has been over-sampled with an acceptable amount of aliasing, we then
Feed it to our DSP for digital filtering to remove the components above W.
Down-sample the signal to some desired rate.
17
Upsampling
Some cases we can only sample a signal at the Nyquist rate;
but need more samples⇒ upsample the data.
Upsampling ⇒ insert correct samples between the original
set ⇒ decrease effective sample interval ⇒ T'S = T
S / M
Time domain: interpolation
Frequency domain: zero padding
18
Upsampling via linear interpolation
, t k
sT
( )x t
( )x k
k 1k + 2k + 3k +, 't k
'sT
( )x t
'( ')x k
'k ' 2k + ' 4k + ' 6k +
upsampling
⇒
(a) (b)
(a) Original signal sampled, (b) signal upsampled by factor of 2
19
Why upsampling?
Upsampling ⇒ greater time resolution
Adaptive filtering methods may require more samples
than obtained by the Nyquist rate
Other DSP algorithms that depend on time resolution may require more than the minimum number of samples
20
Upsampling does not add information
Upsampling
21
In Class Exercise
Problem 6.1-11