Upload
trinhnhan
View
218
Download
0
Embed Size (px)
Citation preview
CV-945 Stand-Alone Biometric Reader
Contents
1.0 Introduction ............................................................................................................................................................... 03
2.0 Mounting .................................................................................................................................................................. 03
3.0 Specifications .......................................................................................................................................................... 04
4.0 Application Diagram ................................................................................................................................................. 04
5.0 Wiring ........................................................................................................................................................................ 05
6.0 Recommended Swiping Technique ............................................................................................................................ 06
7.0 Programming ............................................................................................................................................................. 06
7.1 Adding Admin Finger and delete all users .................................................................................................................... 06
8.0 Administrator Programming ...................................................................................................................................... 06
8.1 Add Finger Relay 1 .................................................................................................................................................... 06
8.2 Add Finger Relay 2 .................................................................................................................................................... 07
8.3 Add Finger Relay 1 & 2 .............................................................................................................................................. 07
8.4 Delete Finger ............................................................................................................................................................ 07
8.5 Delete All Fingers ...................................................................................................................................................... 08
8.6 Change Admin Finger ................................................................................................................................................ 08
8.7 Change Installer Finger .............................................................................................................................................. 08
9.0 Administrator Programming Block Diagram ............................................................................................................... 09
10.0 Installer Programming ............................................................................................................................................ 09
10.1 Set Relay 1 Time .................................................................................................................................................... 09
10.2 Set Relay 2 Time .................................................................................................................................................... 10
10.3 Buzzer ON/OFF ........................................................................................................................................................ 10
10.4 Backlight ON/OFF .................................................................................................................................................... 10
11.0 Installer Programming Block Diagram .................................................................................................................... 11
12.0 Pairing - Biometric and Remote Switch/Relay Unit ................................................................................................... 11
CV-945 Stand-Alone Biometric Reader
CV-945 is a simple one-door standalone biometric system. The reader can store up to 98 finger templates. It has one relay output and one exit button input. If secure installation is needed, the reader can be connected to a remote relay unit in a secured area, which also acts as a request-to-exit push button. Complete setup and programming can be done by scrolling and tapping on the sensor.
The sensor incorporates dedicated sensing hardware to facilitate the detection of “spoofing” attacks based on fake fingers. This data is embedded into the image data stream, and is processed on the processor. The system is capable of detecting and defeating well-known fake finger mechanisms, such as molded “gummy” fingers.
The coating on the surface of the Touch Chip sensor provides protection from scratching and abrasion due to normal contact with fingertips and any incidental contact with fingernails.
RecommendationsConsult with installer about safety level of the installation. There are devices with relays compatible with this reader that can increase the security of the system if needed. One or two enrolled fingers are enough for one user. Ask the installer before he leaves the site to enroll your finger as administrator.
Note The Reader is using physical roughness of the fingerprint to scan the finger. Some of the users may have very flat fingertips, making difficult for the sensor to recognize correctly the fingerprint. In most cases, these are children and older persons. To solve this problem, do the following:
1. Try with different user’s fingers to find the “best” finger.
2. Check with the installer other models of the reader with added card reader or keypad for other type of access.
MaintenanceNo special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use chemicals and materials that can scratch the sensor.
Warning!Do not touch the sensor with other objects than finger. Do not pour or splash with water or other liquids. When painting or construction work is ongoing in the area around the reader, protect the reader sensor area from possible damages and paint. If reader is to be dismounted or relocated, call authorized installer for the job. Disposal of this product must be handled according to all national laws and regulations.
Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antennas.
Do not place the device near or above heating equipment.
If cleaning, do not spray or splash water or other cleaning liquids. Wipe it out with a smooth cloth or towel.
Do not let children touch the device without supervision.
Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and fingerprints cannot be entered.
If the biometric reader is installed and used outdoors, the
reader MUST be fitted with the CV-940-MCP metal cover in order to protect the sensor from direct rainfall or snow. The operating temperature of the product is between -4°F to +122°F (-20ºC - + 50ºC). If the reader is installed in an environment where the temperature can drop below -4°F (-20ºC) and/or the sensor could only be exposed to direct sunlight, it is strongly recommended to install the reader inside a third party sealed wall mount box fitted with an additional heater if the temperature is below -4°F (-20°C) to keep the sensor level performance. Camden cannot guarantee the functionality of the product if these instructions are not followed.
Page 3 of 11
1.0 Introduction
2.0 Mounting
0.2”(5mm)
3 (3 x 1.2”)3 (3 x 30mm)
1 (M3 x 0.2”)1 (M3 x 6mm)
CV-940-MCP
CV-945 Stand-Alone Biometric Reader
3.0 Specifications
Fingerprint Capacity: 98 templatesOutput: 1 x Relay (1 A /24V AC/DC)Push Button Input: YesDoor Open Time: Pulse (1, 3, 5, 10, 20, 30, 60 seconds)
or Toggle(ON/OFF)
Entry Mode: FingerProgramming: By scrolling and tapping on
the sensor or by keypad
Installer/Admin Fingers:
1 Installer + 1 Admin Finger
Image resolution: Up to 508 DPIBacklight ON/OFF: YesBuzzer ON/OFF: YesFirmware Upgrade: Via RS485 converter and
windows application
Current Consumption: 100 mA max.Power Supply: 9-14 V DCIndication: Tricolor Status LED and
4 x Programming LEDs
Mounting: SurfaceIP Factor: IP65Storage/Operating Temperature:
-4°F to +122°F (-20°C to +50°C)
Storage/Operating Humidity:
5% to 93% RH without condensation
Dimensions: 3 5/8” H x 2” W x 1” D (92mm x 51mm x 25mm)
4.0 Application Diagram
Page 4 of 11
(51mm)2”
(92mm)3 5/8”
(25mm)1”
CV-945Stand-Alone Biometric Reader
CV-945HS
(Optional)
1 Relay Remote Unit
and Request-to-Exit Button Secured Area
Outside
RS485164ft. (max. 50m)
CV-945 Stand-Alone Biometric Reader
5.0 Wiring
Page 5 of 11
NCCOM
NO
TampBlue
Yellow
RedBlackPinkViolet
OrangeGray
White
PB
RS485
+_
12VDCPOWER SUPPLY
+_
NCCOM
GND (PB)
PB
+_
Electro Magnetic Lock
Green
Blue
Yellow
RedBlackPinkViolet
OrangeGray
White
Green
Colour Connection
Tamper
12V DCRed
Black
White
Yellow
Grey NCCOM
NO
GNDGreen
Relay(1A)
Push Button Orange
Pink
Violet
Blue Tamper
A (RS485)
B (RS485)
1N4001Diode
12V DCGNDAB
CV-945 Stand-Alone Biometric Reader
Page 6 of 11
7.0 Programming
7.1 Adding Admin Finger and delete all users
1.Push dip switch no.2 to position ON.
2.Reset the Power of the device.
3.Wait for One long + multiple short beeps
4.Put the dip switch in position OFF. (short beeps will stop)
5.Wait for the LED to blink Orange.
6.Swipe the Master finger min.6 times. (Until Ok Beep)
Note: This procedure also deletes all the users and administrators previously enrolled.
x 6
1 2
ON
1 2
ON
No.2
No.2
8.0 Administrator Programming
8.1 ADD Finger Relay 1 (Finger that will activate relay 1)
Use point fingers as Administrator and Installer. You can use the other fingers as access fingers. Administrator finger is enrolled at the end of the system installation. Initial enrollment of the Admin finger is described in installer manual.
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Admin Finger 1 time x 1 slow blinking short beep
Wait 5 seconds (until fast blinking) short beep
Swipe User Finger min. 6 times (until short + long beep)
x 6 fast blinking short + long beep
6.0 Recommended Swiping TechniqueStarting from the first finger joint, place the selected finger on the swipe sensor and move it evenly downward in one steady movement.
Result:
For a valid swipe: Tricolour Status LED turns green + OK Beep (short + long beep)
For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep (3 short beeps)
CV-945 Stand-Alone Biometric Reader
Page 7 of 11
8.2 ADD Finger Relay 2 (Finger that will activate relay 2)
8.3 ADD Finger Relay 1 & 2 (Finger that will activate relay 1 & 2)
8.4 DELETE Finger
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Admin Finger 2 times x 2 slow blinking short beep
Wait 5 seconds (until fast blinking) short beep
Swipe User Finger min. 6 times (until short + long beep)
x 6 fast blinking short + long beep
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Admin Finger 3 times x 3 slow blinking short beep
Wait 5 seconds (until fast blinking) short beep
Swipe User Finger min. 6 times (until short + long beep)
x 6 fast blinking short + long beep
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Admin Finger 4 times x 4 slow blinking short beep
Wait 5 seconds (until fast blinking) short beep
Swipe User Finger x 1 fast blinking short + long beep
Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.
Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.
Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.
CV-945 Stand-Alone Biometric Reader
Page 8 of 11
8.5 DELETE ALL Fingers
8.6 CHANGE ADMIN Finger
8.7 CHANGE INSTALLER Finger
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Admin Finger 4 times x 4 slow blinking short beep
Wait 5 seconds (until fast blinking) slow blinking short beep
Swipe Admin Finger 2 times x 2 fast blinking multiple beeps
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Admin Finger 5 times x 5 slow blinking short beep
Wait 5 seconds (until fast blinking) slow blinking short beep
Swipe NEW Admin Finger min.6 times x 6 fast blinking 3 short beeps
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Admin Finger 6 times x 6 slow blinking short beep
Wait 5 seconds (until fast blinking) slow blinking short beep
Swipe NEW Installer Finger min.6 times
x 6 fast blinking 3 short beeps
CV-945 Stand-Alone Biometric Reader
Page 9 of 11
9.0 Administrator Programming Block Diagram
10.0 Installer Programming
Swipe the ADMIN Finger 1 to 6 times depending of the desired menu
1 SwipeADD Finger
Relay 1
Wait5 seconds
(until fast blinking)
SWIPEnew fingermin. 6 times
END
6 Swipes
Wait5 seconds
(until fast blinking)
SWIPEnew INSTALLER
FINGERmin. 6 times
END
2 SwipesADD Finger
Relay 2
Wait5 seconds
(until fast blinking)
SWIPEnew fingermin. 6 times
END
3 SwipesADD Finger
Relay 1 & 2
Wait5 seconds
(until fast blinking)
SWIPEnew fingermin. 6 times
END
5 SwipesChangeADMINFinger
EnrollINSTALLER
Finger
Wait5 seconds
(until fast blinking)
SWIPEnew ADMIN
FINGERmin. 6 times
END
4 SwipesDELETE FINGER
Relay 1 & 2
Wait5 seconds
(until fast blinking)
SWIPEalready
enrolled finger1 time
END
Wait5 seconds
(until fast blinking)
SWIPEADMIN finger
2 times toDELETE ALL
END
10.1 Set Relay 1 Time
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Installer Finger 1 time x 1 slow blinking short beep
Wait 5 seconds (until fast blinking) short beep
Swipe the INSTALLER Finger and start counting seconds x 1 fast blinking beeps on 1 second
Swipe the INSTALLER Finger to stop or wait 30 seconds to put the relay in toggle mode
x 1 fast blinking short + long beep
CV-945 Stand-Alone Biometric Reader
Page 10 of 11
10.2 Set Relay 2 Time
10.3 BUZZER On/Off
10.4 BACKLIGHT On/Off
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Installer Finger 2 times x 1 slow blinking short beep
Wait 5 seconds (until fast blinking) short beep
Swipe the INSTALLER Finger and start counting seconds x 1 fast blinking beeps on 1 second
Swipe the INSTALLER Finger to stop or wait 30 seconds to put the relay in toggle mode
x 1 fast blinking short + long beep
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Installer Finger 3 times x 3 slow blinking short beep
Wait 5 seconds (until fast blinking) short beep
Swipe INSTALLER Finger x 1 fast blinking short + long beep
ACTION FINGER BACKLIGHT BUZZER SOUND
Swipe Installer Finger 4 times x 4 slow blinking short beep
Wait 5 seconds (until fast blinking) short beep
Swipe INSTALLER Finger x 1 fast blinking short + long beep
Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.
CV-945 Stand-Alone Biometric Reader
Push Buttons Keypads Strikes Magnetic Locks Key Switches Relays & Timers Access Control
5502 Timberlea Blvd., Mississauga, ON Canada L4W 2T7
www.camdencontrols.com Toll Free: 1.877.226.3369
File: CV-945 Stand-Alone Biometric Reader Installation Instructions.indd R2 Revision: 27/03/2017 Part No.: 40-82B184
Page 11 of 11
11.0 Installer Programming Block DiagramSwipe the INSTALLER Finger 1 to 4 times depending of the desired menu
1 SwipeSet
RELAY 1Time
SetRELAY 2
TimeBUZZER
ON/OFFBACKLIGHT
ON/OFF
Wait5 seconds
(until fast blinking)
4 Swipes
Wait5 seconds
(until fast blinking)
2 Swipes
Wait5 seconds
(until fast blinking)
3 Swipes
Wait5 seconds
(until fast blinking)
Swipe the Installer Finger and start counting seconds
Swipe the Installer Finger and start counting seconds
Swipe the Installer Finger to put the Buzzer ON/OFF
Swipe the Installer Finger to put the Backlight ON/OFF
END ENDEND END
Swipe the Installer Finger to stop or wait 30 seconds to put the relay in toggle ON/OFF mode
Swipe the Installer Finger to stop or wait 30 seconds to put the relay in toggle ON/OFF mode
12.0 Pairing - Biometric Reader and Remote Switch/Relay Unit
If a more secure installation is required, the reader can be connected to a remote switch/relay unit in a secured area, which also acts as request-to-exit push button. Follow the instructions bellow to pair (couple) the devices.
1. Put Dipswitch No.1 to position ON. HS beeps continuously and the red LED blinks.
2. Put Dipswitch No.1 to position OFF.
3. Wait for Beep + OK Beep (short + short + long beep)
After the OK beep, the pairing is done.
1 2
ON
12 VDC+-
1N40
07
+
-
HS Switch Relay
Black
Red
Pink
Violet
Black
Brown
Pink
Violet
Red
White
Yellow COM
NOGND
12V out
A (RS485)
B (RS485)
CV-945
12.1 Pairing CV-945HS