Drum Mower CAT 270 plus - poettinger.at

Drum Mower

CAT 270 plus(Type PTM 338 : + . . 01001)

GB Operating instructions Nr. 99 338.GB.80A.0

Ihre / Your / Votre • Masch.Nr. • Fgst.Ident.Nr.

ALLG./BA SEITE 2 / 9300-GB

Important information concerning Product Liability.According to the laws governing product liability, the manufacturer and dealer areobliged to hand the operating manual to the customer at the time of sale, and toinstruct them in the recommended operating, safety, and maintenance regulations.Confirmation is necessary to prove that the machine and operatingmanual have been handed over accordingly.For this purpose, document A is to be signed and sent to Pöttinger,document B remains with the dealer supplying the machine, and thecustomer receives document C.

In accordance with the laws of product liability, every farmer is an entrepreneur.

According to the laws of product liability, property damage is damage caused by amachine and not to it. An excess of Euro 500 is provided for such a liabilioty.

In accordance with the laws of product liability, entrepreneurial property damagesare excluded from the liability.

Attention! Should the customer resell the machine at a later date, the operatingmanual must be given to the new owner who must then be instructed in therecommended regulations referred to herein.

GB

Dear FarmerYou have just made an excellent choice. Naturally weare very happy and wish to congratulate you forhaving chosen Pöttinger. As your agricultural partner,we offer you quality and efficiency combined withreliable servicing.In order to assess the spare-parts demand for ouragricultural machines and to take these demandsinto consideration when developing new machines,we would ask you to provide us with some details.Furthermore, we will also be able to inform you of newdevelopments.

- 3 -(338) INHALT 9800-GB

CONTENTS GB

Observe safety hints in supplement-A

Table of contents

Meaning of warning signs ................................................................... 4

Lowering the frame ............................................................................. 5

Winter storage ..................................................................................... 5

Raising the frame ................................................................................ 5

Attaching implement to tractor ............................................................ 6

Adjusting lower links ............................................................................ 7

Important recommendation! ................................................................ 7

Fitting drive shaft ................................................................................. 7

Conversion from Working to Transport Position .................................. 8

Transport Position 1 ............................................................................ 8


Reducing the Total Height in the Transport Position ............................ 8


Reducing the Total Height in the Transport Position ............................ 9

Conversion from Transport to Working Position .................................. 9

Lowering the Machine ......................................................................... 9

Parking in the open ............................................................................. 9

Take care when turning on slopes! ................................................... 10

Safety hints ....................................................................................... 11

Cutting height adjustment ................................................................. 11

Cutting height adjustment ................................................................. 11

Operation .......................................................................................... 12

Adjustment: ....................................................................................... 12

Adjustment of both swath makers(8i ................................................. 13

Adjustment of swath width(8i ............................................................ 13

Collision safety device: ...................................................................... 14

Function of collision safety device: .................................................... 14

Adjustment: ....................................................................................... 14

Safety points ..................................................................................... 15

General maintenance hints ............................................................... 15

Repair Instructions ............................................................................ 15

Cleaning of machine parts ................................................................ 15

Parking in the open ........................................................................... 15

Winter storage ................................................................................... 15

Drive shafts ....................................................................................... 15

Hydraulic unit .................................................................................... 15

Check initial spring tension. .............................................................. 16

Cutters .............................................................................................. 16

Changing the cutters ......................................................................... 16

Checking the mowing blade suspension ........................................... 16

Mower disc ........................................................................................ 16

Danger of accident if wearing parts are worn ................................... 17

Danger of accident if: ........................................................................ 17

PUTTING AWAY FOR THE WINTER ................................................ 18

Raising the frame .............................................................................. 18

Technical data ................................................................................... 19

The defined use of the mower unit .................................................... 19

Position of Vehicle Identification Plate ............................................... 19

Correct loading .................................................................................. 19

Supplement ....................................................................................... 20

Recommendations for work safety .................................................... 21

DRIVESHAFT ................................................................................... 22

LUBRICATION CHART ..................................................................... 25

Attachment variations ....................................................................... 26

Important! Additional Information ...................................................... 27

Combination of tractor and mounted implement ............................... 27

- 4 -(361) AZB 9700-GB

GBWARNING SIGNS

CE signThe CE sign, which is affixed by the manufacturer, indicates outwardly that this machine conformsto the engineering guideline regulations and the other relevant EU guidelines.

EU Declaration of Conformity (see supplement)By signing the EU Declaration of Conformity, the manufacturer declares that the machine beingbrought into service complies with all relevant safety and health requirements.

Meaning of warning signs

Danger - flying objects; keep safe distance from themachine as long as the engine is running.

Wait until all machine components have stoppedcompletely before touching them.

Stay clear of mower knife area as long as tractorengine is running with PTO connected.

Shut off engine and remove key before performingmaintenance or repair work.

Stay clear of swinging area of implements

Close both side protective coverings before engagingp.t.o..

Never reach into the crushing danger area as longas parts may move.

Recommendations for work safety

All points referring to satety in this manualare indicated by this sign.

495.151

495.167

(354) ANBAU / 9600-GB

ATTACHMENT GB

- 5 -

Lowering the frameSafety hints:

see supplement-A1 points 8a. - 8h.)

- Connect hydraulic snap coupling (60) for swivel cylinder.

- Pull out jack stand and securewith cotter pin.

- Open U-shaped flap(positionA).

- Release hook (16) by means of rope.

- By controlling the tractorservo-valve (ST), lower theframe slowly.

60

TD 79/90/30

TD 79/90/31a

H

Winter storageA rusty plunger rod can damage cylinder's sealingelements.

At season's end

- clean plunger rod and all other shiny parts, then grease them

- park implement withattachment frame (H) raised,which will protect plunger rodfrom rust

- pay attention to the hints inchapter "MAINTENANCE"

Raising the frameSafety hints:

see supplement-A1Pkt.8a. - 8h.)

- Do not attach implement to tractor's lifting gear.

- Connect hydraulic snap coupling (60) for swivel cylinder.


- Control the tractor servo-valve (ST), raise the frame slowly.

TD 79/90/28

16

ST

(338) TRAKANBAU 9800-GB

ATTACHING TO TRACTOR GB

- 6 -

TD25/90/21

15

TD25/90/8

16

Attaching implement to tractor

Safety hints:

see supplement-A1 points 7.), 8a. - 8h.)

- The U-shaped flap (if available) should beswivelled up (A).

In this position the relieving spring is not sostrongly tensioned which enables the mower'sattaching frame to remain horizontal.

- Attach mower so that the edge of the tractor-side drum is just outside the right-hand tractor tyre!

- See also chapter "Side-located attachment", supplement-D

- Adjust lower link bolt (1) on frame accordingly.

- Bring frame into horizontal position by adjusting linkage arm spindle (15).

- By turning upper link spindle (16) the cutting height is adjusted .

(338) TRAKANBAU 9800-GB

ATTACHING TO TRACTOR GB

- 7 -

Adjusting lower links

- Adjust tractor's hydraulics (ST) using bottom stop.

Lower links approx. 600 mm.

This height allows optimal evenness when working on uneven ground and neednot be changed for swinging cutter bar up.

- Connect hydraulic snap coupling for swivel cylinder.

Important recommendation!A transfer, which is located near the gear, adviseswhich p.t.o. speed your mower unit is equipped for.

Standard: Gear for power take-off 1000 rpm.

Order number: spare part book

Fitting drive shaft- Before operating for the first time, drive shaft is to be checked and adapted if

necessary. See alse chapter "Drive Shaft" in supplement B.

ST

1000

rp

m

540

rpm

TD 18/96/2

(358) TRANSPORTSTELLUNG 9500-GB

TRANSPORT AND WORKING POSITION

- 8 -

GB

Transport Position 2• Mower bar only swivelled up at the side.

- Pull on rope (S2) andsimultaneously actuate servo-valve (ST).

- Gradually move cutter bar intovertical position and releaserope(S2).

- Secure cutter bar with hook (13).

- Before driving on roads always check correct locking!

Attention!Never let mowing mechanism run with the mowerraised.

- Connect lighting and raise implement for transport .

- Before leaving the tractor lower cutter bar to ground!

Reducing the Total Height in the TransportPosition

Before converting to transport position

• The external guard plate (10) can be swivelled in to reducethe total height (- 30 cm) when in the transport position.

For safety reasons the mower disks must be at acomplete standstill before swivelling the guard plate.

Conversion from Working to TransportPosition

Safety Precaution!

see supplement-A1 points 7.), 8c. - 8h.)

Changing from working position to transport positionis only to be carried out on even, firm ground.

• The mower bar can be swivelled into 3 different positions fortransportation.

Transport Position 1• Mower bar

swivelled back.

- Lower cutter bar toground.

- Release hook (40)by pulling on therope (S1) and moveforwards with thetractor.

In doing so, thecutter bar swivelsback so far until the hook(41) is locked into position.

- Raise the implement using the tractor's lifting gear.

Note: Only short runs at low speed may be carriedout in this position.

TD47/93/5

30 c

m

10

TD43/92/20

ST

(358) TRANSPORTSTELLUNG 9500-GB

TRANSPORT AND WORKING POSITION

- 9 -

GB

Conversion from Transport to Working Position- Swivel U-shaped flap into position

"G".

When cutting bar is lowered therelieving spring is somewhat moretensioned which enables the bar torest on the ground with less weight.

Swinging cutter bar down

- Make sure that swivel area is freeand that nobody is standing in thedanger area.

- Gently raise cutter bar withswivel cylinder so that hook(13) can be released.

- Release hook (13) by pulling on the rope (S2).

- Lower cutter bar hydraulically.

Lowering the Machine- Before disconnecting hydraulic hose (26) extend cylinder (27) completely,

so that no residual pressure interferes with connecting up later.

Parking in the openWhen parking for longer periods in theopen, clean plunger rods and then coat withgrease.

Transport Position 3• Mower bar swivelled back and then up.

1. Swivel mower bar back as described in "TransportPosition 1".

2. Move mower barinto vertical positionas described in"Transport Position2".

- Secure cutter barwith hook (13).

3. Before driving onroads always checkcorrect locking!

Attention!Never let mowing mechanism run withthe mower raised.

- Connect lighting and raise implementfor transport.

- Before leaving the tractor lower cutter bar toground!

Reducing the Total Height in theTransport Position

In this position the external guard plate can alsobe swivelled in (see previous page).

TD 20/91/2

PÖTTINGER

2726

FETT

TD49/93/2

TD43/92/20

TD25/90/26A

(358) 9500-GB HANGFAHRT - 10 -

WORKING ON SLOPES GB

Take care when turning on slopes!

The tractor's travelling characteristics are influenced by theweight (G) of the mower unit. This can lead to dangeroussituations, especially on slopes.

Danger of tipping occurs

- when the mower unit is facing downhill and in a raised position,

- when travelling in a left-hand curve with the mower unit raised,

- when travelling in a left-hand curve in the transport position (mowerunit completely raised).

Safety advice• Reduce speed in left-hand curves accordingly.

• Travel so that the raised mower unit is facing uphill.

• It is better to travel in reverse on a slope than to carry out a riskyturning manoeuvre.

TD15/95/3

G

TD15/95/2

TD15/95/4

- 11 -338 / INBETRIEBNAHME / 9800-GB

GBSTARTING WORK

TD 28/91/33

TD41/90/37

bsb 447 410

Cutting height adjustment

Safety points

- Turn engine off whenadjustment, service andrepair work is to be done.

- Do not work under themachine without safe support.

- Retighten all screws after the first hours of operation.

Cutting height adjustment

The cutting height can be set anywhere from 30 to 60 mm byadjusting the centre disc.

1. Lift unit with loader.

2. With some means ofassistance, prop upthe mower unit on theframe between themowing drums.

3. The accompanyingkey is put on thesquare and turneduntil the requiredcutting height is set.

Safety hints1. Check:

- Check wear of blade bolt (31).

Replace blade holder when boltdiameter is less than 9 mm.

- Check blade holder (30) on damage.

- In case of grinding noisescheck whether the bladeholder (30) is buckled andtherefore the blade does not lie correctly any more.

2. Turn p.t.o. on.

Turn the p.t.o. on only when all safety devices (coverings, protectiveaprons, casings, etc.) are in proper condition and attached to theimplement in the correct protective positions.

3. Switch-on the machine only in working position and do notexceed the prescribed power take-off speed (for example max.540 rpm).

A transfer, which is located near the gear, advises which p.t.o. speed yourmower unit is equipped for.

4. Pay attention to correct p.t.o. direction of rotation!

To mow, slowly throw in the p.t.o. away from the mowing area and bringthe mowing rotor up to full speed. The travelling speed depends onground contours and type of forage.

5. Stay clear while engine is running

Refer people to thedanger area, the dangercoming from stones whichare flung away. Particularcare is advisable onstoney ground and nearroads and paths.

6. Wear hearing protection

The noise level in the workplace can deviate from the measured value (seeTechnical Data) partly because of the differing cabin types ofvarious tractors.

• If a noise level of 85 dB (A) is reached or exceeded, thefarmer must have suitable hearing protection in readiness (UVV1.1 §2).

• If a noise level of 90 dB (A) is reached or exceeded, the hearing protectionmust be worn (UVV1.1 § 16).

7. Damage protection!

• The surface to be mowed must be free of obstructions or foreign objects.Such objects (e.g. large stones, pieces of wood, boundary stones, etc.)can damage the mower unit.

In the event of a collision

• Stop immediately and switch off the drive.

• Carefully check the implement for damage.

• Have the implement checked also by a specialist workshop if necessary.

8. Safety hints (pt. 1, 2, 3, 4,) to observe in supplement A1!

- 12 -338 / INBETRIEBNAHME / 9800-GB

GBSTARTING WORK

TD25/90/8

16

TD79/90/34

Operation

1. Adjust cutting height by turning upper link spindle(inclination of the cutting discs max. 5°).

2. To mow, gradually supply power to the p.t.o. beforeentering the crop and bring the mowing discs up to fullrevs.

Smoothly increase the p.t.o. speed, in order to avoid noisesin the free-wheel conditioned by the system.

- Adjust travel speed to terrain and crop.

Adjustment:- Adjust tractor hydraulics in a way that the machine can adapt

to uneven ground.- Bolt (B) in the centre of the guide.

That means the lowest position (600 mm) of hydraulics mustbe limited.

- Frame horizontal.

- Fix hydraulic lower links in a way that the machine cannotswing out sideways.

9800-GB SCHWADFORMER (338)

Field operation GB

- 13 - (8i see Supplement-A

Adjustment of both swath makers(8i

Leading swath disc• Distance between mowing plate and swath disc "5-10 mm ".

• inclination 5°

Rear swath disc

Adjustment "+10 mm".

Adjustment of swath width(8i

The swath width can be altered by changing the position of the levers (6).

If an obstruction appears then the swath width is to be increased.

TD 25-98-5

10 mm TD 25-98-3+ 10 mm

TD 25-98-2

6

5°

TD 37-98-02

TD 25-98-4

5-10 mm

(338) ANFAHRSICHERUNG 9900-GB

COLLISION SAFETY DEVICE GB

- 14 -

Collision safety device:When mowing around trees, fences, boundary stones etc., collisions between thecutter bar and obstacles can occur despite careful and slow driving. Therefore, inorder to prevent such damage, collision protection has been planned for the cuttingdevice.

Attention!It is not the intention of the collision safety device to prevent damage to the machinewhen working at full speed.

Function of collision safety device:If the mower encounters an obstacle, the springloaded hook (1) is released and thecutter bar can swing back.

If you reverse a short distance then, the hook is relocked into position.

Adjustment:

In case the safety device trips to easy adjust hexagonal nut.

Adjusting measurement: 100 mm

IF YOU ARE NOT SURE WHETHER THE CUTTING AREA ISREALLY FREE OF OBSTACLES, PLEASE WORK AT ANAPPROPRIATE SLOW SPEED!

PÖ

TT

ING

ER

CA

T 2

30

PÖ

TT

ING

ER

TD41/90/32

(358) ALLG. WARTUNG 0000-GB - 15 -

MAINTENANCE GB

Safety points

• Turn engine off when adjustment,service and repair work is to bedone.

• Do not work under the machinewithout safe support.

• Retighten all screws after the firsthours of operation.

General maintenance hints

In order to keep the implement in good condition afterlong periods of operation, please observe the followingpoints:

- Tighten all screws after the first hours of operation.

Check blade screws in particular.

- Observe maintenance hints for angular gear andcutter bar.

Spare parts

a. The original components and accessories have been designedespecially for these machines and appliances.

b. We want to make it quite clear that components and accesories that havenot been supplied by us have not been tested by us.

c. The installation and/or use of such products can, therefore, negativelychange or influence the construction characteristics of the appliance. Weare not liable for damages caused by the use of components andaccessories that have not been supplied by us.

d. Alterations and the use of auxiliary parts that are not permitted by themanufacturer render all liability invalid.

Repair Instructions

Please refer to repair instructions in supplement

Cleaning of machine parts

Attention! Do not use high-pressurewashers for thecleaning of bearing-and hydraulic parts.

- Danger of rust!

- After cleaning, greasethe machine accordingto the lubrication chartand carry out a short test run.

- Cleaning with too high pressure may dodamage to varnish.

Parking in the open

When parking in the open forlong periods of time, cleanpiston rods and then coat withgrease.

Winter storage

- Thoroughly clean machine before storage.

- Put up protection against weather.

- Change or replenish gear oil.

- Protect exposed parts from rust.

- Lubricate all greasing points according to lubrication chart.

Drive shafts

- see supplement

Hydraulic unit

Caution! Danger of injury or infection!

Under high pressure, escaping fluids can penetrate the skin.Therefore seek immediate medical help!

After the first 10 operating hours and then everyconsecutive 50 operating hours

- Check the hydraulic unit and lines for tightness and retightenscrew connections if necessary.

Before operation

- Check hydraulic hoses for wear.

Replace worn or damaged hydraulic hoses immediately. Thereplacement hoses must meet the manufacturer’s technicalrequirements.

FETT

TD49/93/2

338 / WARTUNG / 9900-GB

MAINTENANCE GB

- 16 -

75 kg

TD 71-98-05

Cutters

The cutters on a cutting drum should be evenly worn out, (dangerof imbalance) otherwise they are to be replaced by new ones.

Pay attention to correct assembly!- Cutters with the notation “L” are only

to be mounted on the left rotatingmowing drum.

- Cutters with the notation “R” are onlyto be mounted on the right rotatingmowing drum.

Changing the cutters

- Prop up the lever (29) on the lower edgeof the drum and push the moveableholder (30) downwards. The cutter (14)is hung on the bolt (31). Change thecutters and clean all forage away thatthe cutter held from around the bolt.Perhaps the inner side of the drum also.Remove the lever (29) andcheck if the cutter holder bolt(31) has returned to its originalposition and if the cutter canmove freely on the bolt.

- When the bolt (31) is greatlyworn, the holder (30) should bereplaced.

Fahrtrichtung

TD 86/98/08

RL

Checking the mowing bladesuspension

- Check immediately afterdriving over a hard obstacle.

- Normal check every 100hours.

- Check more often whenmowing on rocky terrain.

Mower disc

With mower discs that are worn in the mowing bladearea, you must proceed as follows:

- Remove lower support disc.

- Remove cutter holder nuts.

- Shift cutter holder around 1 hole (60o).

- Tighten screws firmly (120Nm) and re-check after afew hours of operation.

- Re-mount mowing blades.

Check initial springtension.

1. Set tractor’s lifting gear at„600 mm“

2. Set spring tension at the 75mm mark.This mesaurement should betaken as an approx. value.

• More important is that theground - bearing load of thecutter bar should be approx.75 kg.

- Set spring tensionaccordingly.

GBMOUNTING OF MOWING BLADECHECKING WEAR

- 17 -0000-GB SICHTKONTROLLE (348)

Attention !

Danger of accident if wearing parts are worn

Wearing parts are:- mounting of mowing blades (30)

- bolts of mowing blades (31)

If such wearing parts are worn out they mustnot be used any longer , otherwise it can nolonger be guaranteed that the pin of the mowingblade is firmly adjusted and accidents may becaused through parts that are flinged away (e.g.mowing blades, fragments...)

Check the suspension of mowing blades as towear and other damage:

- every time before bringing the machine into operational use

- several times during use

- immediately after hitting an obstacle (e.g. a stone, piece of wood,metal,...)

Process of visual control:1. remove mowing blades

2. remove grass and dirt- around pin (31)

Attention !

Danger of accident if:

- the wearing area (30a) is worn up to the pin of the mowingblade(30b)

- the pin diameter is 9 mm or less

- the profile is only 5 mm or less (original measure = 7 mm)

- the riveted joint (1 ) of the pin is worn

- the pin (31) of the blade is no longer firmly seated

If you notice one or several of thesecharacteristics of wear stop mowing at once!

Worn parts must be replaced by original partsmade by Pöttinger immediately !

30aTD 59-00-09

3030b

7 mm

min.5 mm

1

TD 59-00-10

TD 79-99-0331

30

GBPUTTING AWAY FOR THE WINTER

- 18 -9800-GB EINWINTERUNG (338)

PUTTING AWAY FOR THE WINTER

- dismantle the pads in order to clean and conserve the undersideof the mowing discs

- lubricate the mower as per schedule.

A rusty plunger rod can damage cylinder's sealingelements.

At season's end

- clean plunger rod and all other shiny parts, then grease them

- park implement with attachment frame (H) raised, which willprotect plunger rod from rust

Raising the frame

Safety hints:

see supplement-A1 Pkt. 8a. - 8h.)

- Do not attach implement to tractor's lifting gear.

- Connect hydraulic snap coupling for swivel cylinder.


- Control the tractor servo-valve (ST), raise the frame slowly.

TD 79/90/28

16

ST

FETT

TD49/93/2

TD 79/90/31a

H

- 19 -TECHN. DATEN / 9900-GB (338)

GBTECHNICAL DATA

M o dell

A . P ö t t i n g e r M a s c h i n e n f a b r i k G e s . m . b . H .A - 4 7 1 0 G r i e s k i r c h e n O b e r ö s t e r r e i c h

Masch.Nr.

Ty p e Ge s . G e w .

Correct loading

The defined use of the mower unit

The "CAT 270 plus (Type PTM 338)" mower is intended solely for normal usein agricultural work.

• The mowing of grassland and short stemmed fodder.Any other uses outside of these are regarded as undefined.The manufacturer takes no responsibility for any resulting damage which occurshenceforth. The risk is carried by the user alone.

• The keeping of operating, service and maintenance requirements layed down bythe manufacturer also come under the heading of "defined use".

Ihre/Your/VotreMasch.Nr. / Fgst.Ident.Nr.

Position of Vehicle Identification Plate

The factory number is imprinted on the accompanying VehicleIdentification Plate (as shown) and on the frame. Guaranteeissues and further inquiries cannot be processed without thefactory number being stated.

Please enter the number onto the front page of the operatingmanual immediately after taking delivery of the vehicle/implement.

CAT 270 plus (Type PTM 338)

Three-point linkage (adjustable) Cat. II

Working width 2,65 m

No. of mowing drums 4

No. of knives per drum 3

Hydraulic lift (single-acting)

Coverage up to 3 ha/h

Max. p.t.o. speed 100 rpm

Drive shaft 1300 Nm

Weight approx. 830 kg

Required power from 44 kW (60 PS)

Torque limiter 1300 Nm

Permanent sound emmission level 90,4 dB(A)

Optional equipment:

Lighting

Warning table

All data subject to revision.

Technical data

GB-ANHANG TITELBLATT (341)

Supplement

(341) SICHERHEIT 9400 GB

SUPPLEMENT - A


All points refering to safety in this manual are indicatedby this sign.

1.) Defined use

a. See "Technical Data".

b. The keeping of operating, service and maintenancerequirements layed down by the manufacturer also comeunder the heading of "defined use".

2.) Spare parts

a. The original components and accessories have beendesigned especially for these machines and appliances.

b. We want to make it quite clear that components andaccesories that have not been supplied by us have notbeen tested by us.

c. The installation and/or use of such products can, therefore,

negatively change or influence the constructioncharacteristics of the appliance. We are not liable fordamages caused by the use of components andaccessories that have not been supplied by us.

d. Alterations and the use of auxiliary parts that are notpermitted by the manufacturer render all liability invalid.

3.) Protection devices

All protection devices must remain on the machine and bemaintained in proper condition. Punctual replacement ofworn and damaged covers is essential.

4.) Before starting work

a. Before commencing work, the operator must be aware ofall operating devices and functions. The learning of theseis too late after having already commenced operation!

b. The vehicle is to be tested for traffic and operating safetybefore each operation.

5.) Asbestos

- Certain sub-supplied components of thevehicle may contain asbestos due totechnical reasons. Observe the warningon spare parts.

6.) Transport of persons prohibited

a. The transport of persons on the machine is not permitted.

b. The machine may only be driven on public roads when inthe position stipulated for road transport.

7.) Driving ability with auxiliary equipment

a. The towing vehicle is to be sufficiently equiped withweights at the front or at the rear in order to guarantee thesteering and braking capacity (a minimum of 20% of thevehicle’s tare weight on the front axle).

b. The driving ability is influenced by ground conditions andby the auxiliary equipment. The driving must be adaptedto the corresponding terrain and ground conditions.

c. When driving through curves with a connected appliance,observe the radius and swinging mass of the appliance.

d. When travelling in a curve with attached or semimountedimplements, take into account the working range andswing mass of the implement!

8.) General

a. Before attaching implement to three-point linkage, movesystem lever into a position whereby unintentional raisingor lowering is ruled out!

b. Danger of injury exists when coupling implement to tractor!

c. Danger of injury through crushing and cutting exists in thethree-point linkage area!

d. Do not stand between tractor and implement when usingthree-point linkage external operation!

e. Attach and detach drive shaft only when motor has stopped.

f. When transporting with raised implement, secure operatinglever against lowering!

g. Before leaving tractor, lower attached implement to theground and remove ignition key!

h. Nobody is to stand between tractor and implement withouttractor being secured against rolling using parking brakeand/or wheel chocks!

i. For all maintenance, service and modification work, turndriving motor off and remove universal drive.

9.) Cleaning the machine

Do not use high-pressure washers for the cleaning ofbearing- and hydraulic parts.

20%Kg

- A 1 -


0000-GB GELENKWELLE (341)

DRIVESHAFT GBSupplement - B

1) How a cam type cut out safety clutch works:This overload clutch switchesthe torque transmitted to zeroif overloaded. To revert tonormal operation, stop thep.t.o. drive briefly.The clutch reengages at aspeed below 200 rpm.

IMPORTANT !The overload clutch on the driveshaft is not a “Full up” indicator. Itis purely a torque limiter designed to protect the implement againstdamage.Driving the right way will avoid triggering the clutch too often, andthus causing unnecessary wear on it and the implement.

2) Wide-angle joint :Maximum angle of deflection when working/stationary : 70°

3) Standard joint :Maximum angle of deflectionwhen stationary: 90°Maximum angle of deflectionwhen working: 35°

MaintenanceReplace worn-outcovers/guards at once.

- Lubricate with a brand-name grease before starting work and every 8 hours worked.

- Before any extended period of non-use, clean and lubricatedriveshaft.

For winterworking, greasethe tube guards,to avoid themfreezing together.

• Important for driveshafts with frictionclutch

Prior to initial operation and after long periods outof use, check friction clutch for proprer function.a.) Measure dimension „L“ at compression spring

of K90, K90/4 and K94/1 or at set screw ofK92Eand K92/4E.

b.) Loosen screws to release the pressure on thefriction disk.

c.) Tighten set screws to dimension „L“.Clutch is ready for use.

DRIVESHAFT

Important! Only use the indicated oraccompanying drive shaft, otherwisethe right to claim under guarantee forany possible damage does not exist.

Matching driveshaft to tractorTo determine the actual lengthrequired, hold the two halves of thedriveshaft side by side.

Procedure for cutting to length- To determine length required, set implement in closest working

position (L2) to tractor, hold driveshaft halves side by side and markoff.

Important!• Note the maximum

operating length (L1)- Try to attain the

greatest possibleshaft over-lap(min. 1/2 X)!

• Shorten inside andoutside tube guardby the same amount.

• Fit torque limiter (2) of driveshaft to implement end ofdriveshaft!

• Always check that drive shaftlocks are securely engagedbefore starting work.

Retaining chain- Use chain to prevent tube guard

from rotating.Take care that chain does notimpede driveshaft pivoting.

Rules for workingNever exceed the maximum p. t. o.speed when using the implement.- When the p.t.o. is switched off,

the implement hitched up may not stop at once.Do not go close to the implement until all motion has stopped; onlythen may work be done on it.

- When the implement istparked, either remove thedriveshaft and store it, orsecure it with a chain. (Do notuse retaining chain (H) for this).

XX

L1

L2

X

Xmin.

TD

52/

97/3

7

- B 1 -

8 h

FETT

L

L

K92E,K92/4E

K90,K90/4,K94/1

Lu

bri

fica

nti

Ed

izio

ne

1997

DG

BI

Bet

rieb

ssto

ffe

Au

sgab

e 19

97

Lu

bri

can

ts

Ed

itio

n 1

997

Leis

tung

und

Leb

ensd

auer

der

Mas

chin

esi

nd v

on s

orgf

ältig

er W

artu

ng u

nd d

erV

erw

endu

ng g

uter

Bet

riebs

stof

fe a

bhän

gig.

Uns

ere

Bet

riebs

stof

fauf

listu

ng e

rleic

hter

td

ie

r ich

tig

e

Au

swa

hl

ge

eig

ne

ter

Bet

riebs

stof

fe.

Im

Sch

mie

rpla

n

ist

de

r je

we

ils

ein

zuse

tze

nd

e

Be

trie

bss

toff

d

urc

h

die

Be

trie

bss

toff

ken

nza

hl

(z.B

. “I

II”)

sym

bo

lisi

ert

. A

nh

an

d

von

“Bet

riebs

stof

fken

nzah

l” ka

nn d

as g

efor

dert

eQ

ualit

ätsm

erkm

al u

nd d

as e

ntsp

rech

ende

Pro

dukt

der

Min

eral

ölfi r

men

fes

tges

tel lt

wer

den.

Die

Lis

te d

er M

iner

alöl

firm

en e

rheb

tke

inen

Ans

pruc

h au

f Vol

lstä

ndig

keit.

The

per

form

ance

and

the

lifet

ime

of th

efa

rm m

achi

nes

are

high

ly d

epen

ding

on

a ca

refu

l mai

nten

ance

and

app

licat

ion

of c

orre

ct l

ubri

cant

s. O

ur s

ched

ule

enab

les

an e

asy

sele

ctio

n of

sel

ecte

dpr

oduc

ts.

The

app

licab

le lu

bric

ants

are

sym

boliz

ed(e

g. “

III”)

. A

ccor

ding

to

this

lub

rican

tpr

oduc

t cod

e nu

mbe

r the

spe

cific

atio

n,qu

ality

and

bra

ndna

me

of o

il co

mpa

nies

may

eas

ily b

e de

term

ined

. The

list

ing

ofth

e oi

l co

mpa

nies

is

not

said

to

beco

mpl

ete.

Pre

stat

ies

en l

even

sduu

r va

n de

mac

hine

s zi

jn a

fhan

kelij

k va

n ee

nzo

rgvu

ldig

ond

erho

ud e

n he

t geb

ruik

van

goed

e sm

eerm

idde

len.

Dit

sch

em

a

verg

em

akk

el i j

kt

de

go

ed

e

keu

ze

van

d

e

juis

tesm

eerm

idde

len.

III

IIIIV

VV

IV

II

HY

DR

AU

LIK

öL H

LPD

IN 5

1524

Tei

l 2

Sie

he A

nmer

kung

en* ** **

*

Mot

oren

öl S

AE

30

gem

äßA

PI C

D/S

F

mot

or o

il S

AE

30

acco

rdin

g to

AP

I CD

/SF

huile

mot

eur

SA

E 3

0 ni

veau

AP

I CD

/SF

oilo

mot

ore

SA

E 3

0 se

cond

osp

ecifi

che

AP

I CD

/SF

Get

riebe

öl S

AE

90

bzw

. 85

W-

140

gem

äß A

PI-

GL

5

gear

oil

SA

E 9

0 re

sp. S

AE

85

W-1

40 a

ccor

ding

to A

PI-

GL

5

huile

tran

smis

sion

SA

90

ouS

AE

85

W-1

40, n

ivea

u A

PI G

L5 oi

lio p

er c

ambi

e d

iffer

enzi

ali

SA

E 9

0 o

SA

E 8

5 W

-140

seco

ndo

spec

ifich

e A

PI-

GL

5

Kom

plex

fett

(DIN

51

502:

KP

1R

)

com

plex

gre

ase

grai

sse

com

plex

e

gras

so a

bas

e di

sap

oni

com

ples

si

Get

riebe

fließ

fett

(DIN

51

502:

GO

H

tran

smis

sion

gre

ase

grai

sse

tran

smis

sion

gras

so fl

uido

per

rid

utto

ri e

mot

orod

utto

ri

Li-F

ett (

DIN

51

502,

KP

2K

)

lithi

um g

reas

e

grai

sse

au li

thiu

m

gras

so a

l liti

o

Get

riebe

öl S

AE

90

bzw

. SA

E 8

5 W

-140

gem

äß A

PI-

GL

4 od

er A

PI-

GL

5

gear

oil,

SA

E 9

0 re

sp. S

AE

85

W-1

40ac

cord

ing

to A

PI-

GL

4 or

AP

I-G

L 5

huile

tran

smis

sion

SA

E 9

0 ou

SA

E 8

5 W

-140

, niv

eau

AP

I-G

L 4

ou A

PI-

GL

5

olio

per

cam

bi e

diff

eren

zial

i SA

E 9

0o

SA

E 8

5W-1

40 s

econ

do s

peci

fiche

AP

I-G

L 4

o A

PI-

GL

5

(II)

ÖL

gefo

rder

tes

Qua

lität

smer

kmal

requ

ired

qual

ity le

vel n

ivea

u

de p

erfo

rman

ce d

eman

dé

cara

tteris

tica

richi

esta

di

qual

it à

verla

ngte

kw

alite

itske

nmer

ken

Bet

rieb

ssto

ff-K

enn

zah

lL

ub

rica

nt

ind

icat

or

Co

de

du

lub

rifi

ant

Nu

mer

o c

arat

teri

stic

o d

ellu

bri

fica

nte

Olie

in

aand

rijv

inge

n vo

lgen

s de

gebr

uiks

aanw

ijzin

g ve

rwis

sele

n -

echt

er te

nmin

ste

1 x

jaar

lijks

.-

Öla

blaß

schr

aube

her

ausn

eh-

men

, das

Altö

l aus

lauf

en la

ssen

und

ordn

ungs

gem

äß e

ntso

rgen

.

Ge

trie

be

öl

ge

mä

ß

Be

trie

bsa

nle

itun

g

-je

doch

min

dest

ens

1 x

jähr

lich

wec

hsel

n.-

Öla

blaß

schr

aube

her

ausn

ehm

en, d

asA

ltöl a

usla

ufen

lass

en u

nd o

rdnu

ngs-

gem

äß e

ntso

rgen

.

Ge

ar

oils

a

cco

rdin

g

to

op

era

tin

gin

stru

ctio

ns -

how

ever

at

leas

t on

ce a

year

.-

Tak

e ou

t oil

drai

n pl

ug, l

et ru

n ou

t and

duly

dis

pose

was

te o

il.

Mot

ori

a qu

attr

o te

mpi

: bi

sogn

a ef

fettu

are

il ca

mbi

ode

ll'ol

io o

gni 1

00 o

re d

i fun

zion

amen

to e

que

llo d

ell'o

liope

r cam

bi c

ome

stab

ilito

nel

man

uale

del

le is

truz

ioni

per

l'uso

(tu

ttavi

a, a

lmen

o 1

volta

all'

anno

).-

Tog

liere

il t

appo

di s

caric

o a

vite

del

l’olio

; fa

r sc

olar

el’o

lio e

elim

inar

e l’o

lio c

ome

prev

isto

dal

la le

gge

anti-

inqu

inam

ento

am

bien

tale

.

Sm

eerm

idd

elen

co

de

Vo

or

he

t b

uite

n

ge

bru

ik

ste

llen

(win

terp

eri

od

e)

de

o

lie

-wis

el

uit

voe

ren

e

n

all

e

vetn

ipp

el

smee

rpun

ten

door

smer

en.

Bla

nke

met

aald

elen

(kop

pelin

gen

enz.

) met

een

prod

ukt

uit

groe

p "I

V"

van

dena

volg

ende

tab

el t

egen

cor

rosi

ebe

sche

rmen

.

Bef

ore

gara

ging

(w

inte

r se

ason

) an

oil

chan

ge a

nd g

reas

ing

of a

ll lu

bric

atin

gpo

ints

has

to

be d

one.

Unp

rote

cted

,bl

anc

met

al p

arts

out

side

(jo

ints

, et

c.)

have

to b

e pr

otec

ted

agai

nst c

orro

sion

with

a g

roup

"IV

" pr

oduc

t as

indi

cate

don

the

reve

rse

of th

is p

age.

Sm

eerm

idd

elen

Uit

gav

e 19

97

NL

Lu

bri

fian

ts

Éd

itio

n 1

997

F

Le b

on f

onct

ionn

emen

t et

la lo

ngév

itéde

s m

achi

nes

dépe

nden

t d’u

n en

tret

ien

soig

neux

et

de l

’util

isat

ion

de b

ons

lubr

ifian

ts.

Not

re l

iste

fac

ilite

le

choi

xco

rrec

t des

lubr

ifian

ts.

Sur

le ta

blea

u de

gra

issa

ge, o

n tr

ouve

un c

ode

(p.e

x."I

II")

se r

éfér

ant

à un

lubr

ifian

t don

né. E

n co

nsul

tant

ce

code

on

p

eu

t fa

cile

me

nt

dé

term

ine

r la

spéc

ifica

tion

dem

andé

e du

lub

rifia

nt.

La l

iste

des

soc

iété

s pé

trol

ière

s ne

prét

end

pas

d’êt

re c

ompl

ète.

Pou

r l’h

uile

tra

nsm

issi

on c

onsu

lter

leca

hier

d’e

ntre

tien

- au

moi

ns u

ne f

ois

par

an.

-R

etire

r le

bouc

hon

de v

idan

ge, l

aiss

erl'h

uil

e

s'é

cou

ler

et

l'éli

min

er

corr

ecte

men

t.

L'ef

ficie

nza

e la

dur

ata

della

mac

chin

a di

pend

ono

dall'

accu

rate

zza

della

sua

man

uten

zion

e e

dall'

impi

ego

dei

lubr

ifica

nti

adat

ti. I

l no

stro

ele

nco

dei

lubr

ifica

nti

Vi

agev

ola

nella

sce

lta d

el lu

brifi

cant

e gi

usto

.

Il lu

brifi

cant

e da

util

izza

rsi d

i vol

ta in

vol

ta è

sim

boliz

zato

nello

sch

ema

di lu

brifi

cazi

one

da u

n nu

mer

o ca

ratte

ristic

o(p

er e

s. "

III")

. In

bas

e al

"nu

mer

o ca

ratte

ristic

o de

llu

brifi

cant

e" s

i po

sson

o st

abili

re s

ia l

a ca

ratte

ristic

a di

qual

ità c

he i

l pr

oget

to c

orris

pond

ente

del

le c

ompa

gnie

petr

olife

re.

L'el

enco

del

le c

ompa

gnie

pet

rolif

ere

non

hapr

etes

e di

com

plet

ezza

.

Vor

Stil

legu

ng (

Win

terp

erio

de)

Ölw

echs

eldu

rchf

ühre

n un

d al

le F

etts

chm

iers

telle

nab

schm

iere

n. B

lank

e M

etal

lteile

auß

en(G

elen

ke, u

sw.)

mit

eine

m P

rodu

kt g

emäß

“IV

” in

der

um

seiti

gen

Tab

elle

vor

Ros

tsc

hütz

en.

Ava

nt

l’arr

êt

et

hiv

er:

vi

da

ng

er

et

grai

sser

. M

étau

x nu

s à

l' ex

téri

eur

prot

éger

ave

c un

pro

duit

type

“IV

” con

tre

la r

ouill

e (c

onsu

lter

tabl

eau

au v

erso

).

Effe

ttuar

e il

cam

bio

dell'

olio

ed

ingr

assa

re tu

tte le

par

ti ch

eric

hied

ono

una

lubr

ifica

zion

e a

gras

so p

rima

del

ferm

oin

vern

ale

della

mac

chin

a. P

rote

gger

e da

lla r

uggi

ne tu

ttele

par

ti m

etal

liche

est

erne

sco

pert

e co

n un

pro

dotto

ano

rma

di "I

V" d

ella

tabe

lla ri

port

ata

sul r

etro

del

la p

agin

a.

(IV)

FE

TT

- D

1 -

-O

SO 3

2/46

/68

ARN

ICA

22/4

6M

OTO

RO

IL H

D 3

0SI

GM

A M

ULT

I 15W

-40

SUPE

R T

RAC

TOR

OIL

UN

IVER

S.15

W-3

0

RO

TRA

HY

80W

-90/

85W

-140

RO

TRA

MP

80W

-90/

85W

-140

GR

MU

2G

R S

LLG

R L

FOR

OTR

A M

P 80

W-9

0R

OTR

A M

P 85

W-1

40

VITA

M G

F 32

/46/

68VI

TAM

HF

32/4

6SU

PER

KO

WAL

30

MU

LTI

TUR

BOR

AL S

UPE

R T

RAK

TOR

AL15

W-3

0

GET

RIE

BEÖ

L EP

90

GET

RIE

BEÖ

LH

YP 8

5W-9

0AR

ALU

B H

L 2

ARAL

UB

FDP

00AR

ALU

B FK

2G

ETR

IEBE

ÖL

HYP

90

AG

IP

AR

AL

*B

ei V

erbu

ndar

beit

mit

Naß

brem

sen-

schl

eppe

rn is

t die

inte

rnat

iona

leS

pezi

fikat

ion

J 20

Aer

ford

erlic

h

**H

ydra

ulik

öle

HLP

-(D

) + H

V

***

Hyd

raul

iköl

e au

fP

flanz

enöl

basi

s H

LP +

HV

Bio

logi

sch

abba

ubar

, des

halb

beso

nder

s um

wel

t-fre

undl

ich

IVA

NM

ER

KU

NG

EN

IIIV

IV

VII

III

Firm

a

Com

pany

Soc

iété

S

ocie

tá(I

V)

FE

TT

(II)

ÖL

*W

hen

wor

king

inco

njun

ctio

n w

ith w

et-

brak

e tra

ctor

s, th

ein

tern

atio

nal

spec

ifica

tion

J 20

A is

nece

ssar

y.

**H

ydra

ulic

oil

HLP

-(D

) + H

V.

***

Hyd

raul

ic o

il w

ithve

geta

ble

oil b

ase

HLP

+ H

V is

bio

-deg

rada

ble

and

is th

eref

ore

espe

cial

ly s

afe

for t

heen

viro

men

t.

HYD

RAU

LIKÖ

L H

LP 3

2/46

/68

SUPE

R 2

000

CD

-MC

*H

YDR

A H

YDR

. FLU

ID *

HYD

RAU

LIKÖ

L M

C 5

30 **

PLAN

TOH

YD 4

0N **

*

SUPE

R 2

000

CD

-MC

SUPE

R 2

000

CD

HD

SU

PER

IOR

20

W-3

0H

D S

UPE

RIO

R S

AE 3

0

SUPE

R 8

090

MC

HYP

OID

80W

-90

HYP

OID

85W

-140

MU

LTI F

ETT

2SP

EZIA

LFET

T FL

MPL

ANTO

GEL

2 N

GET

RIE

BEFL

IESS

FETT

NLG

I 0R

ENO

LIT

DU

RAP

LEX

EP 0

0PL

ANTO

GEL

00N

REN

OPL

EX E

P 1

HYP

OID

85W

-140

BA

YW

A

AVIL

UB

RL

32/4

6AV

ILU

B VG

32/

46M

OTO

RO

IL H

D 3

0M

ULT

IGR

ADE

HD

C 1

5W-4

0TR

ACTA

VIA

HF

SUPE

R 1

0 W

-30

GET

RIE

BEÖ

L M

Z 90

M M

ULT

IHYP

85W

-140

AVIA

MEH

RZW

ECKF

ETT

AVIA

ABS

CH

MIE

RFE

TTAV

IA G

ETR

IEBE

FLIE

SSFE

TTAV

IALU

B SP

EZIA

LFET

T LD

GET

RIE

BEÖ

L H

YP 9

0 EP

MU

LTIH

YP85

W-1

40 E

PA

VIA

ENER

GO

L SH

F 32

/46/

68VI

SCO

200

0EN

ERG

OL

HD

30

VAN

ELLU

S M

30

GEA

R O

IL 9

0 EP

HYP

OG

EAR

90

EPEN

ERG

REA

SE L

S-EP

2FL

IESS

FETT

NO

ENER

GR

EASE

HTO

OLE

X PR

914

2H

YPO

GEA

R 9

0 EP

HYP

OG

EAR

85W

-140

EP

BP

HYS

PIN

AW

S 32

/46/

68 H

YSPI

NAW

H 3

2/46

RX

SUPE

R D

IESE

L 15

W-4

0PO

WER

TRAN

SEP

X 80

W-9

0H

YPO

Y C

80W

-140

IMPE

RVI

A M

MO

CAS

TRO

LGR

EASE

LM

XEP

X 80

W-9

0H

YPO

Y C

80W

-140

CA

ST

RO

L

WIO

LAN

HS

(HG

) 32/

46/6

8W

IOLA

N H

VG 4

6 **

WIO

LAN

HR

32/

46 **

*H

YDR

OLF

LUID

*

MU

LTI-R

EKO

RD

15W

-40

PRIM

ANO

LR

EKO

RD

30

HYP

OID

-GET

RIE

BEÖ

L80

W-9

0, 8

5W-1

40M

EHR

ZWEC

KGET

RIE

BEÖ

L80

W-9

0

WIO

LUB

LFP

2W

IOLU

B G

FWW

IOLU

B AF

K 2

HYP

OID

-GET

RIE

BEÖ

L80

W-9

0, 8

5W-1

40

ENAK

HLP

32/

46/6

8EN

AK M

ULT

I 46/

68SU

PER

EVV

ARO

L H

D/B

SAE

30

UN

IVER

SAL

TRAC

TOR

OIL

SU

PER

HYP

OID

GA

90H

YPO

ID G

B 90

HO

CH

DR

UC

KFET

T LT

/SC

280

GET

RIE

BEFE

TT M

O 3

70EV

VA C

A 30

0H

YPO

ID G

B 90

HLP

32/

46/6

8H

LP-M

M32

/M46

MO

TOR

ÖL

100

MS

SAE

30M

OTO

RÖ

L 10

4 C

M 1

5W-4

0AU

STR

OTR

AC 1

5W-3

0

GET

RIE

BEÖ

L M

P 85

W-9

0G

ETR

IEBE

ÖL

B 85

W-9

0G

ETR

IEBE

ÖL

C 8

5W-9

0

LOR

ENA

46LI

TOR

A 27

RH

ENO

X 34

-G

ETR

IEBE

ÖL

B 85

W-9

0G

ETR

IEBE

ÖL

C 8

5W-1

40

OLN

A 32

/46/

68H

YDR

ELF

46/6

8PE

RFO

RM

ANC

E 2

B SA

E 30

800

0TO

UR

S 20

W-3

0 TR

ACTO

REL

F ST

15W

-30

TRAN

SELF

TYP

B 9

0 85

W-1

40TR

ANSE

LF E

P 90

85W

-140

EPEX

A 2

RO

LEXA

2M

ULT

I 2

GA

O E

PPO

LY G

OM

ULT

IMO

TIVE

1TR

ANSE

LF T

YP B

90

85W

-140

TRAN

SELF

TYP

BLS

80

W-9

0

NU

TO H

32/

46/6

8N

UTO

HP

32/4

6/68

PLU

S M

OTO

RÖ

L 20

W-3

0 U

NIF

ARM

15W

-30

GEA

RO

IL G

P 80

W-9

0 G

EAR

OIL

GP

85W

-140

MU

LTI P

UR

POSE

GR

EASE

HFI

BRAX

EP

370

NEB

ULA

EP

1G

P G

REA

SEG

EAR

OIL

GX

80W

-90

GEA

R O

IL G

X 85

W-1

40

ULT

RAM

AX H

LP 3

2/46

/68

SUPE

RTR

AC F

E 10

W-3

0* U

LTR

AMAX

HVL

P 32

**U

LTR

APLA

NT

40 **

*

SUPE

R H

PO 3

0ST

OU

15W

-30

SUPE

R T

RAC

FE

10W

-30

ALL

FLEE

T PL

US

15W

-40

HP

GEA

R O

IL 9

0od

er 8

5W-1

40TR

ANS

GEA

R O

IL 8

0W-9

0

MU

LTIL

UBE

EP

2VA

L-PL

EX E

P 2

PLAN

TOG

EL 2

N

REN

OLI

T LZ

R 0

00D

EGR

ALU

B ZS

A 00

0D

UR

APLE

X EP

1

TELL

US

S32/

S 46

/S68

TEL

LUS

T32

/T46

AGR

OM

A 15

W-3

0R

OTE

LLA

X 30

RIM

ULA

X 1

5W-4

0

SPIR

AX 9

0 EP

SPIR

AX H

D 9

0SP

IRAX

HD

85/

140

RET

INAX

AAL

VAN

IA E

P 2

SPEZ

. GET

RIE

BEFE

TT H

SIM

MN

IAG

REA

SE O

AER

OSH

ELL

GR

EASE

22

DO

LIU

MG

REA

SE R

SPIR

AX H

D 9

0SP

IRAX

HD

85W

-140

AZO

LLA

ZS 3

2, 4

6, 6

8 EQ

UIV

IS Z

S32

, 46,

68

RU

BIA

H 3

0M

ULT

AGR

I TM

15W

-20

TOTA

L EP

85W

-90

TOTA

L EP

B 8

5W-9

0M

ULT

IS E

P 2

MU

LTIS

EP

200

MU

LTIS

HT

1TO

TAL

EP B

85W

-90

DTE

22/

24/2

5D

TE 1

3/15

HD

20W

-20

DEL

VAC

123

0SU

PER

UN

IVER

SAL

15W

-30

MO

BILU

BE G

X 90

MO

BILU

BE H

D 9

0M

OBI

LUBE

HD

85W

-140

MO

BILG

REA

SE M

PM

OBI

LUX

EP 0

04M

OBI

LPLE

X 47

MO

BILU

BE H

D 9

0M

OBI

LUBE

HD

85W

-140

REN

OPL

EX E

P 1

HYP

OID

EW

90

HYP

OID

85W

-140

HYD

RAU

LIK Ö

L H

LP/3

2/46

/68

HYD

RAM

OT

1030

MC

*H

YDR

AULI

K ÖL

520

**PL

ANTO

HYD

40N

***

MU

LTI 2

030

2000

TC

HYD

RAM

OT

15W

-30

HYD

RAM

OT

1030

MC

GET

RIE

BEÖ

L M

P 90

HYP

OID

EW

90

HYP

OID

85W

-140

MEH

RZW

ECKF

ETT

SPEZ

IALF

ETT

GLM

PLAN

TOG

EL 2

N

GET

RIE

BEFL

IESS

FETT

PLAN

TOG

EL 0

0N

HYD

RAN

32/

46/6

8D

ELTA

PLU

S SA

E 30

SUPE

R U

NIV

ERSA

L O

ILPO

NTO

NIC

N 8

5W-9

0 PO

NTO

NIC

MP

85W

-90

85W

-140

SUPE

R U

NIV

ERSA

L O

IL

MAR

SON

EP

L 2

NAT

RAN

00

MAR

SON

AX

2PO

NTO

NIC

MP

85W

-140

REN

OPL

EX E

P 1

REN

OG

EAR

SU

PER

809

0 M

CR

ENO

GEA

R H

YPO

ID 8

5W-1

40R

ENO

GEA

R H

YPO

ID 9

0

TITA

N H

YDR

AMO

T 1O

3O M

CTI

TAN

UN

IVER

SAL

HD

REN

OG

EAR

SU

PER

809

0 M

CR

ENO

GEA

R H

YPO

ID 8

5 W

-140

REN

OG

EAR

HYP

OID

90

REN

OSO

D G

FO 3

5D

UR

APLE

X EP

00

PLAN

TOG

EL 0

0N

ELA

N

FU

CH

S

GE

NO

L

MO

BIL

RH

G

SH

ELL

TO

TA

L

ELF

ES

SO

EV

VA

FIN

A

VA

LVO

LIN

E

VE

ED

OL

REN

OLI

N B

10/

15/2

0 R

ENO

LIN

B32

HVI

/46H

VIEX

TRA

HD

30

SUPE

R H

D 2

0 W

-30

MEH

RZW

EC

KGET

RIE

BEÖ

lSA

E90

HYP

OID

EW

90

MEH

RZW

ECKF

ETT

REN

OLI

T M

PD

UR

APLE

X EP

REN

OSO

D G

FO 3

5R

ENO

PLEX

EP

1H

YPO

ID E

W 9

0

--

AND

ARIN

32/

46/6

8H

D P

LUS

SAE

30M

ULT

IGR

ADE

SAE

80/9

0M

ULT

IGEA

R B

90

MU

LTIG

EAR

C S

AE 8

5W-1

40

MU

LTIP

UR

POSE

MU

LTIG

EAR

B 9

0M

ULT

I C S

AE 8

5W-1

40

WIN

TE

RS

HA

LL

HP

GEA

R O

IL 9

0od

er 8

5W-1

40

REN

OLI

N 1

025

MC

***

TITA

N H

YDR

AMO

T 10

30 M

C **

REN

OG

EAR

HYD

RA

*PL

ANTO

HYD

40N

***

REN

OLI

T M

PR

ENO

LIT

FLM

2R

ENO

LIT

ADH

ESIV

2PL

ANTO

GEL

2 N

CAS

TRO

LGR

EASE

LM

- D

2 -

- D 25 -0000 SCHMIERPLAN (338)

FETT

TD 86/98/07

(IV)F E T TIII

0,5 Liter

III11 Liter

50 h 1 J1 J

2,5 - 3,5 cm

9900 LEGENDE-SCHMIERPL / BA/EL ALLG / BETRIEBSSTOFFVORSCHRIFT

Schmierplan

8h alle 8 Betriebsstunden20h alle 20 Betriebsstunden

40 F alle 40 Fuhren80 F alle 80 Fuhren

1 J 1 x jährlich100 ha alle 100 Hektar

FETT FETT

= Anzahl der Schmiernippel(IV) Siehe Anhang "Betriebsstoffe"

Liter Liter* Variante

Siehe Anleitung des Herstellers

Plan de graissage

8h Toutes les 8 heures de service20h Toutes les 20 heures de service

40 F Tous les 40 voyages80 F Tous les 80 voyages

1 J 1 fois par an100 ha tous les 100 hectares

FETT GRAISSE

= Nombre de graisseurs(IV) Voir annexe "Lubrifiants"

Liter Litre* Variante

Voir le guide du constructeur

Lubrication chart

8h after every 8 hours operation20h after every 20 hours operation

40 F alle 40 operations80 F alle 80 operations

1 J once a year100 ha every 100 hectares

FETT GREASE

= Number of grease nipples(IV) see supplement "Lubrificants"

Liter Litre* Variation

See manufacturer’s instructions

Smeerschema

8h alle 8 bedrijfs uren20h alle 20 bedrijfs uren

40 F alle 40 wagenladingen80 F alle 80 wagenladingen

1 J 1 x jaarlijks100 ha alle 100 hektaren

FETT VET

= Aantal smeernippels(IV) Zie aanhangsel "Smeermiddelen"

Liter Liter* Varianten

zie gebruiksaanwijzing van de fabrikant

FETT

Schema di lubrificazione

8h ogni 8 ore di esercizio20h ogni 20 ore di esercizio

40 F ogni 40 viaggi80 F ogni 80 viaggi

1 J volta all'anno100 ha ogni 100 ettari

FETT GRASSO

= Numero degli ingrassatori(IV) vedi capitolo “materiali di esercizio”

Liter litri* variante

vedi istruzioni del fabbricante

I Esquema de lubricación

8h Cada 8 horas de servicio20h Cada 20 horas de servicio

40 F Cada 40 viajes80 F Cada 80 viajes

1 J 1 vez al ano100 ha Cada 100 hectáreas

FETT FETT

= Número de boquillas de engrase(IV) Véase anexo “Lubrificantes”

Liter Litros* Variante

Véanse instrucciones del fabricante

Plano de lubrificação

8h Em cada 8 horas de serviço20h Em cada 20 horas de serviço

40 F Em cada 40 transportes80 F Em cada 80 transportes

1 J 1x por ano100 ha Em cada100 hectares

FETT Lubrificante

= Número dos bocais de lubrificação(IV) Ver anexo ”Lubrificantes"

Liter Litro* Variante

Ver instruções do fabricante

E P

NL

D F GB

Smörjschema

8h Varje 8:e driftstimme20h Varje 20:e driftstimme

40 F Varje 40: e lass80 F Varje 80: e lass

1 J 1 x årlingen100 ha Varje 100:e ha

FETT FETT

= Antal smörjnipplar(IV) Se avsnitt ”Drivmedel”

Liter Liter* Utrustningsvariant

Se tillverkarens anvisningar

S Smøreplan

8h Hver 8. arbeidstime20h Hver 20. arbeidstime

40 F Hvert 40. lass80 F Hvert 80. lass

1 J 1 x årlig100 ha Totalt 100 Hektar

FETT FETT

= Antall smørenipler(IV) Se vedlegg "Betriebsstoffe"

Liter Liter* Unntak

Se instruksjon fra produsent

N

Mazací plán

8h kaûd˝ch 8 hodin20h kaûd˝ch 20 hodin

40 F kaûd˝ch 40 voz˘80 F kaûd˝ch 80 voz˘

1 J 1 x roËnÏ100 ha po 100 ha

FETT TUK

= PoËet mazacÌch hlaviËek(IV) Viz kapitola "Mazací prostfiedky vydání "

Liter litru* Varianta

viz. pfiíruËka v˝robce

Kenési terv

8h minden 8 üzemóra után20h minden 20 üzemóra után

40 F minden 40 menet után80 F minden 80 menet után

1 J 1-szer évente100 ha minden 100 Hektár után

FETT ZSÍR

= A zsírzógombok száma(IV) Nézd a "Kenôanyagok" c. fejezetet

Liter Liter* Változat

Nézd a gyártó utasításait!

CZ H Схема смазки

8h чеpез каждые 8 часов pаботы20h чеpез каждые 20 часов pаботы

40 F чеpез каждые 40 подвод80 F чеpез каждые 80 подвод

1 J 1 pаз в год100 ha чеpез каждые 100 га

FETT СМАЗКА / OIL МАСЛО

= количество смазочных ниппелей

(IV) См. пpиложение «Эксплуатационные матеpиалы»Liter литp (количествово масла, жидкость,...)

* Ваpиант

Смотpи pуководство изготовителя

RUS

GBSide-located attachment

- E1 -9600-GB SEITENVERSATZ (358)

Attachment variations

Example: Tractor with a width of 195 cm.

1. Attachment variation (7 cm)• Install lower link bolts according to sketch

- left 10 cm

- right 15 cm

2. Attachment variation (17 cm)• interchange left and right lower link bolts and install according to

sketch

- left 20 cm

- right 5 cm

3. Attachment variation (27 cm)• As in point 2, but in addition

- relocate lower links about 10 cm to the right

195 cm

7 cm

17 cm

10 cm

27 cm

TD 26/96/6

195 cm

7 cm

17 cm20 cm 5 cm

TD 26/96/5

15 cm

195 cm

7 cm

SB

100 cm

TD 26/96/7

10 cm

0000-GB ZUSINFO / BA-EL ALLG.

GB

- Z.27 -

see instruction handbook of the tractor

see price list and/or instruction handbook of the implement

to be measured

Consideration of rear mounted implement and front/rear combinations1. CALCULATION OF MINIMUM BALLASTING AT THE FRONT GV min

Record the calculated minimum ballasting which is needed at the front of the tractor into the table.

Front mounted implement2. CALCULATION OF THE MINIMUM GH min

Record the calculated minimum ballasting which is needed at the rear of the tractor into the table.

For the calculation you need the following data:TL [kg]

TV [kg]

TH [kg]

GH [kg]

GV [kg]

unladen weight of tractor

front axle load of unladen tractor

rear axle load of unladen tractor

combined weight of rear mounted implement/rearballast

combined weight of front mounted implement/frontballast

distance from centre of gravity forcombined front mounted implement/frontballast to front axle centre

Tractor wheelbase

distance from rear axle centre to centre oflower link balls

distance from centre of lower link balls tocentre of gravity for combined rearmounted implement/rear ballast

a [m]

b [m]

c [m]

d [m]

2

31

1

1

1

1

2

2

2

3

3

1

3

2

Important! Additional Information

Combination of tractor and mounted implement

The mounting of implements on the front or rear three point linkage shall not result in exceeding the maximum permissibleweight, the permissible axle loads and the tyre load carrying capacities ot the tractor. The front axle of the tractor mustalways to be loaded with at least 20 % of the unladen weight of the tractor.

Make sure before buying an implement that these conditions are fulfilled by carrying out the following calculations or byweighing the tractor/implement combination.

Determination of the total weight, the axle loads, the tyre load carrying capacity and thenecessary minimum ballasting

0000-GB ZUSINFO / BA-EL ALLG.

GB

- Z.28 -

Minimum ballastingfront/rear

Total weight

Front axle load

Rear axle load

Real value according tocalculation

Permissible valueaccording to instruc-

tion handbook

Double permissible tyreload carrying capacity (two

tyres)

The minimum ballasting has to be attached to the tractor either in form of a mountedimplement or ballasting weight!The calculated values must be less or equal (<) the permissible values!

3. CALCULATION OF THE REAL FRONT AXLE LOAD TV tat

(If with the front mounted implement (GV) the required minimum front ballasting (GV min) cannot be reached, the weight of the front mounted implementhas to be increased to the weight of the minimum ballasting at the front!)

Record the calculated real front axle load and the permissible front axle load of the tractor into the table.

4. CALCULATION OF THE REAL TOTAL WEIGHT Gtat

(If with the rear mounted implement (GH) the required minimum rear ballasting (GH min) cannot be reached, the weight of the rear mounted implementshas to be increased to at least the weight of the minimum ballasting at the rear!)

Record the calculated real and the permissible total weight given in the instruction handbook for the tractor into the table.

5. CALCULATION OF THE REAL REAR AXLE LOAD TH tat

Record the calculated real and the permissible rear axle load given in the instruction handbook for the tractor into the table.

6. TYRE LOAD CARRYING CAPACITYRecord double the value (two tyres) of the permissible load carrying capacity into the table (see for instance documentation provided by the tyremanufacturer).

Table

Important! Additional informationCombination of tractor and mounted implement

ALOIS PÖTTINGER Maschinenfabrik Gesellschaft m.b.H.

A-4710 Grieskirchen; Industriestraße 1

9401

D/F

/GB

/NL/

I/E/P

/S/S

F E

G K

onfo

rmitä

tser

kl. (

543)

pa. Ing. W. LeposaEntwicklungsleitungGrieskirchen, 21..02.2000

Trommelmäher CAT 270 plus, Type PTM 338

EN 292-1 : 1991 EN 292-2 : 1991

Appendix 1

GB

________________________ ________________________________(Place and date of issue) (Name and job function of authorized person)

EC Certificate of Conformityconforming to EEC Directions 89/392

We _______________________________________________________________________(name of supplier)

_________________________________________________________________________(full address of company - where this concerns authorized agents within the Common Market, also state the companyname and manufacturer)

declare in sole responsibility, that the product

_________________________________________________________________________(make, model)

to which this certificate applies, conforms to the basic safety and health requirements ofEECDirections 89/392,(if applicable)and to the other relevant EEC Directions.

_________________________________________________________________________(title and/or number and date of issue of the other EEC Directions)

(if applicable)To effect correct application of the safety and health requirements stated in the EEC Directions,the following standards and/or technical specifications were consulted:

_________________________________________________________________________(title and/or number and date of issue of standards and/or specifications)

Following the policy of the PÖTTINGERGes.m.b.H to improve their products as

technical developments continue, PÖTTINGER reservethe right to make alterations which must not necessarilycorrespond to text and illustrations contained in thispublication, and without incurring obligation to alterany machines previously delivered.

Technical data, dimensions and weights are given asan indication only. Responsibility for errors or omissionsnot accepted.

Reproduction or translation of this publication, in wholeor part, is not permitted without the written consent ofthe ALOIS PÖTTINGER

Maschinenfabrik Gesellschaft m.b.H.

A-4710 Grieskirchen.

All rights under the provision of the Copyright Act arereserved.

La société PÖTTINGER Ges.m.b.H amélioreconstamment ses produits grâce au le progrès

technique. C'est pourquoi nous nous réservons le droitde modifier descriptions et illustrations de cette noticed'utilisation, sans qu'on en puisse faire découler undroit à modifications sur des machines déjà livrées.

Caractéristiques techniques, dimensions et poids sontsans engagement. Des erreurs sont possibles.

Copie ou traduction, même d'extraits, seulement avecla premission écrite de

ALOIS PÖTTINGER



Tous droits réservés selon la réglementation des droitsd'auteurs.

De PÖTTINGER Ges.m.b.H werkt perma-nent aan de verbetering van hun produkten in

het kader van hun technische ontwikkelingen. Daarommoeten wij ons veranderingen van de afbeeldingen enbeschrijvingen van deze gebruiksaanwijzingvoorbehouden, zonder dat daaruit een aanspraak opveranderingen van reeds geieverde machines kanworden afgeleid.

Technische gegevens, maten en gewichten zijn nietbindend. Vergissingen voorbehouden.

Nadruk of vertailing ook gedeeltelijk, slechts metschiftelijke toestemming van de

ALOIS PÖTTINGER



Alle rechten naar de wet over het auteursrechtvoorbehouden.

La empresa PÖTTINGER Ges.m.b.H seesfuerza contínuamente en la mejora

constante de sus productos, adaptándolos a laevolución técnica. Por ello nos vamos obligados areservarnos todos los derechos de cualquiermodificación de los productos con relación a lasilustraciones y a los textos del presente manual, sinque por ello pueda ser deducido derecho alguno a lamodificación de máquinas ya suministradas.

Los datos técnicos, las medidas y los pesos seentienden sin compromiso alguno.

La reproducción o la traducción del presente manualde instrucciones, aunque sea tan solo parcial, requierede la autorización por escrito de

ALOIS PÖTTINGER



Todos los derechos están protegidos por la ley de lapropiedad industrial.

D

NL

GBF

E

Im Zuge der technischen Weiterentwicklungarbeitet die PÖTTINGER Ges.m.b.H ständig

an der Verbesserung ihrer Produkte.

Änderungen gegenüber den Abbildungen und Be-schreibungen dieser Betriebsanleitung müssen wiruns darum vorbehalten, ein Anspruch auf Änderungenan bereits ausgelieferten Maschinen kann daraus nichtabgeleitet werden.

Technische Angaben, Maße und Gewichte sind unver-bindlich. Irrtümer vorbehalten.

Nachdruck oder Übersetzung, auch auszugsweise,nur mit schriftlicher Genehmigung der

ALOIS PÖTTINGER



Alle Rechte nach dem Gesetz des Urheberrecht vorbe-halten.

La PÖTTINGER Ges.m.b.H è costantementeal lavoro per migliorare i suoi prodottimantenendoli aggiornati rispetto allo sviluppo

della tecnica.

Per questo motivo siamo costretti a riservarci la facoltàdi apportare eventuali modifiche alle illustrazioni e alledescrizioni di queste istruzioni per l’uso. Allo stessotempo ciò non comporta il diritto di fare apportaremodifiche a macchine già fornite.

I dati tecnici, le misure e i pesi non sono impegnativi.Non rispondiamo di eventuali errori. Ristampa otraduzione, anche solo parziale, solo dietro consensoscritto della

ALOIS PÖTTINGER



Ci riserviamo tutti i diritti previsti dalla legge sul dirittod’autore.

I

V d˘sledku technickÈho v˝voje pracujefirma PÖTTINGER Ges.m.b.H neust·le

na zlepöenÌ sv˝ch v˝robk˘.

ZmÏny v n·vodu k pouûÌv·nÌ si v˝robce vyhrazuje.Poûadavky na zmÏnu n·vodu k pouûÌv·nÌ napr·vÏ dodanÈ stroje nemohou b˝t vyvozov·ny.

TechnickÈ ˙daje, rozmÏry a hmotnosti jsounez·vaznÈ.

Dotisk nebo nov˝ p¯eklad je moûn˝ pouze zapÌsemnÈho souhlasu firmy

ALOIS PÖTTINGER


A-4710 Grieskirchen

Vöechna pr·va podlÈhajÌ autorskÈmu pr·vu.

CZВ ходе технического развития фирма«ПЁТТИНГЕР Гез.м.б.Х.» постояннозанимается усовершенствованием своей

продукции.

В связи с этим мы сохраняем за собой право вноситьизменения в рисунки и описания этой инструкции поэксплуатации, однако,требование вносить такиеизменения в уже поставленные машины предъявлениюне подлежит.

Технические данные, указание размеров и массы даютсябез обязательств. Ошибки не исключены.

Перепечатка или перевод, в том числе отрывками,разрешается только с письменного согласия фирмы

«АЛОЙС ПЁТТИНГЕР

Машиненфабрик Гезельшафт м.б.Х.»

А-4710 Грискирхен.

С сохранением всех прав в соответствии с авторскимправом.

RUS

GEBR. PÖTTINGER GMBHServicezentrumSpöttinger-Straße 24Postfach 1561D-86 899 LANDSBERG / LECHTelefon:

Ersatzteildienst: 0 81 91 / 92 99 - 166 od. 169Kundendienst: 0 81 91 / 92 99 - 130 od. 231

Telefax: 0 81 91 / 59 656

ALOIS PÖTTINGERMaschinenfabrik Gesellschaft m.b.HA-4710 Grieskirchen

Telefon: 0043 (0) 72 48 600-0Telefax: 0043 (0) 72 48 600-511

e-Mail: [email protected]: http://www.poettinger.co.at

GEBR. PÖTTINGER GMBHStützpunkt NordWentruper Mark 10D-48 268 GrevenTelefon: (0 25 71) 93 45 - 0

Ersatzteildienst: (0 25 71) 93 45 - 11Kundendienst: (0 25 71) 93 45 - 12

Telefax: (0 25 71) 93 45 - 14

PÖTTINGER France129 b, la ChapelleF-68650 Le Bonhomme

Tél.: 03.89.47.28.30Fax: 03.89.47.28.39

Documents

Drum Mower CAT 270 plus - poettinger.at