Embed Size (px)
Citation preview
SPECIFICATIONSWingspan:.........................2060mm (81.1in)Length:................................1450mm (57 in)Electric Motor:.....................See next pagerGas Engine:................................. 26-30ccRTF Weight: 7Kg / 15.5lbs (Will vary withEquipment Used).Radio:...............7-8 Channel / 10-11 ServosFunction: Ailerons-Elevator-Rudder-ThrottleFlaps-Optional Retractable Landing Gear.
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll andcause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kannhoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe umprofessionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells istdurch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
Radio control model / Flugmodel
ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY
U.S NAVY DIVE BOMBER
Instruction manual / MontageanleitungTECHNISCHE DATENSpannweite:...................................2060mmLange:............................................1450mmElektroantrieb.............(siehe nächste Seite)Verbrennerantrieb:..........................26-30ccFluggewicht:..........................................7KgFernsteuerung......7-8 Kanal / 10-11 Servos
VQ No: VQA123
1.5mm
A B
!
CAL/R
Assemble left and right sides the same way. X
Drill holes using the stated
size of drill (in this case 1.5 mm )
Use epoxy glue
Take particular care hereHatched-in areas:remove covering film carefully
Not included.These parts must be
purchased separately
Check during assembly that theseparts move freely, without binding
Apply cyano glue
SILICONCA
GLUE
Silicon sealer Cyanoacrylate Glue (thin type)
Minimum 7-8 channels radiowith 10 mini servos and 1 standardServo (for GP).
Extension cord for aileron servos: 80cm(x2)
TOLLS REQUIREDHobby knife
Needle nose Pliers
Phillip screw driverAwl
ScissorsWire Cutters
(Purchase separately) Hex Wrench
..................................................................................................................
..................................................................................................................
..................................................................................................................
..................................................................................................................
..................................................................................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual, comprise:
(Purchase separately)
.Motor control x1(for GP) .Elevator x2
.Rudder x1. Aileron x2. Flap x3
CONVERSION TABLE
1.0mm = 3/64”1.5mm = 1/16”2.0mm = 5/64”2.5mm = 3/32”
3.0mm = 1/8”4.0mm = 5/32”5.0mm = 13/64”6.0mm = 15/64”
10mm = 13/32”12mm = 15/32”15mm = 19/32”20mm = 51/64”
25mm = 1”30mm = 1-3/16”45mm = 1-51/64”
If exposed to direct sunlight and/or heat, wrinkels can appear. Storing themodel in a cool place will let the wrinkles disappear. Otherwise, removewrinkles in covering film with a hair dryer, starting withlow temperature. You can fix the corners by using a hot iron.
Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Faltenentstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Foliezu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !
REQUIRED FOR OPERATION (Purchase separately)
Low seting
Extension cord for flap and brake servos: 50cm(x4)Extension cord for retract servos: 30cm(x2)Extension cord for Rx battery pack: 30cm(x1)
.Brake x2
Spinner hub
EPOXY A
EPOXY B
Epoxy Glue (30 minute type)
Extension cord for Elevator servos: 80cm(x2)
Gas engine:26-30cc
Plastic strap
Main landing gear
Gear mount (plywood)
Ply gear mount plate
Square plastic
3x20mm
3x20mm
Ply gear mount plate
Square plastic
Main gear (left)
Main gear (right)
Gear mount (plywood)
Plastic strap
3x20mm screw..16
1- Fixed gear
CA
CA
ON
OFF
GEARSWITCH
2- Electric retract
9
10
CA
8 7
B
A
CA
CA
C1
C4
1
C415 15
17
C1
17
1 2
3
5
6
4
7
4
7
19
19
19
19
19 19
Bo1
Bo2
Bo3
Bo4
SB
D
AB
A B
A B
9
8
8
10
11
12
AT
13
14
16
18
C3
C2
19
20 21 22
24
24 24
24
24
25
25
AB9 10
10
25
A9 B
3- Cover
4- Joining the wing
25x960mmaluminum tube
Flap and brake push rod(one end to servo)
Flap and brakecontrol horn
Brake servo
Flap servo
Aileron servo Hatch
Servomount
WING BOTTOM
AIL.
Included with the radio set
Aileron servohatch (ply 3mm)
Connector............3
Control horn
................2
2x30mm ..........4
5- Servo
5x20mm screws
.....2
6- Joining the wing
A
A
X
X
7- Engine
Step 1
Step 2
Step 3
Step 4
Step 5
Note: Remove the magnetic canopyHatch first.
Filler tube
To engine
Rubberstopper
CapStopper
Air tube
Step 6
8- Engine
9- Fuel tank
10- Electric Motor
11- Magnetic canopy hatch
12- Cowling
Elevator servo hatch
HORIZONTAL STABILIZER(Bottom-view)
CA
CA
13- Horizontal stabilizer
6mm diameter dowel
Note: The holes on the surface of the bottom of the horizontal stabilizer are pre-drilled at factory.
2.mm drill bit
Aluminumtube inside 3x10mm screw
BOTTOM A
B
3x10mm screw
.........2
Secure the horizontal stabilizer in place using 3x10mm screw.
WRONG
RIGHT
Control horn
................2
2x20mm ..........4
Connector.....2
14- Horizontal stabilizer
15- Tail wheel
Note: Slide one end of thetail wheel push-rod into thetail wheel arm first.
Rudder controlhorn
1.5mm
1.5mm
16- Rudder
CA
CA
2.5mm
C1
C4
1
C415 15
17
C1
17
1 2
3
5
6
4
7
4
7
19
19
19
19
19 19
CA
44
5
2
3
CACA
1
CA
CA
CA
CA
6
CA
17- Guns
19B01
Bo220
Bo221
Bo422
CA
CA
CA
CA
CA
CA
CA
CA
18- Bomb
1919
19
Bo1
Bo2
Bo3
Bo4
SB
D
AB
A B
A B
9
8
8
10
11
12
AT
13
14
16
18
C3
C2
19
20 21 22
24
24 24
24
24
25
25
AB9 10
10
25
A9 B
3mm
CA
19- Bomb
24
24
24
11mm diameteraluminum tube
2mm diameter steel wire
Silicon tube
20- Bomb
CA
CA
Nylon control horn
CA
CA
1.5mm
CA
CA
21- Bomb
25
2x6mm screw
CA
WING- TOP VIEW
Black nylon wire
CA CA
Black nylon wire
Wing surface
Do the same way with other side
CA
168mm diameter aluminum tube
BLACK NYLON TUBE
CA
CA
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
......
......
......
......
......
......
......
......
......
...
18
C3
14
C2
CA
CA
CA
15
17
Wing - bottom view
22- Hook
X2
23- Decor
Magnetic Pilot sitter
Remove beforeinstalling servo
Switch hole
Rudderpush rod
Tail wheelpush rod
FUSELAGE TOP-VIEW
Connector............2
24- Rudder servo
25- Guns - Antenna
CA
CA
11
AILERON STROKE
ELEVATOR STROKE
RUDDER STROKE
Adjust the travel of the control surfaces to achieve the values stated in the diagrams.These value will be suitable for average flight requirements. Adjust the values to suit your particular needs.
CENTER FLAP STROKE
(40mm)
(128 ~ 133mm)
Note: Adjust the location of the battery pack to achieve this C.G location.
DO NOT try to fly an out-of balance model!
Wing center section
RIGHT&LEFT FLAP STROKE (40mm)
(15mm)
(15mm)
(25mm)
(25mm)
(20mm)
(20mm)
IMPORTANT: Please do not clean your model with strong solvent or pure alcohol, only use kerosene to keep the colour of your model not fade.
(40mm)
RIGHT&LEFT BRAKE STROKE
26- Balance
27- Control surface
