JACC2 Addenda 001 Specs

X:\2014\7986.14\BID-PROPOSAL PHASE\PKG2 - Addenda 001\7986.14 Addenda 001.docm

4222 85th Street

Lubbock, Texas 79423

806.473.2200

Abilene Amarillo Austin El Paso Las Cruces Lubbock Midland team-psc.com

Package II ADDENDUMNO: 001

TO: Prospective Bidders

FROM: Parkhill, Smith & Cooper, Inc.

PROJECT NAME: Joe Arrington Cancer Center Renovations

PROJECT NO.: 7986.14

DATE: March 27, 2015

Attention of all Prospective Bidders/Plan Holders is directed to the following modifications to the referenced Drawings and Project Manual. This Addendum becomes a part of the Contract Documents and modifies the original Contract Documents dated March, 2015 as noted below:

This Addendum consists of two (2) pages, Spec Section 02518, Spec Section 02523, Spec Section 02810, Spec Section 02920, Spec Section 02930 and the attached drawings as listed below.

I. CHANGES TO PROJECT MANUAL:

A. SPEC SECTION 02518 INTERLOCKING CONCRETE PAVERS 1. Add in its entirety

B. SPEC SECTION 02523 CONCRETE CURBS, GUTTERS, & SIDEWALKS 1. Add in its entirety

C. SPEC SECTION 02810 IRRIGATION SYSTEMS 1. Add in its entirety

D. SPEC SECTION 02920 LAWNS & GRASSES 1. Add in its entirety

E. SPEC SECTION 02930 EXTERIOR PLANTS 1. Add in its entirety

F. SPEC SECTION 09000 FINISH MATERIAL LEGEND 1. Add in its entirety

II. CHANGES TO DRAWINGS (BY DISCIPLINE)

A. GENERAL 1. SHEET G-001-2

a. See revisions as clouded

B. LANDSCAPE 1. Landscape sheet set in its entirety

C. ARCHITECTURE 1. Sheets A-103A-2, A-103B-2, A-103C-2, A-104A-2, A-104B-2, A-104C-2, A-113B-2, A-

113C-2, A-114B-2, A-114C-2, A-115-2, A-116-2, A-211-2, A-212-2, A-213-2, A-214-2, A-215-2, A-311-2, A-321-2, A-322-2, A-401-2, A-402-2, A-501-2, A-603-2, A-701-2

a. See revisions as clouded

Addendum No. 001 Page 2 03/27/2015

a. See revisions as clouded 2. Sheets A-216-2, A-217-2, A-218-2, A-312-2, A-403-2, A-404-2, A-702-2

a. Sheets added in their entirety D. INTERIOR

1. Sheets ID-1.00, ID-1.01A, ID-1.01B, ID-1.01C, ID-1.02 A&C, ID-1.02B, ID-3.01A, ID-3.01B, ID-4.01, ID-5.00, ID-6.00, ID-6.02

a. See revisions as clouded 2. SHEETS ID-5.03, ID-5.04, ID-5.05, ID-5.06

a. Sheets added in their entirety

E. PLUMBING 1. Plumbing sheet set in its entirety

F. MECHANICAL

1. Mechanical sheet set in its entirety

G. ELECTRICAL 1. Electrical sheet set in its entirety 2. Elekta equipment drawings included as supplemental information

Joe Arrington Cancer Center Renovations and Additions Phase 2

03798614 FINISH MATERIAL LEGEND 090000 - 1 03/15, Addendum 001

SECTION 09000 FINISH MATERIAL LEGEND

(Partial List) PART 1 GENERAL 1.01 SUMMARY

A. Section includes: Finish material/colors legend

1.02 MANUFACTURED CASEWORK (Section 06402) A. Plastic Laminate Faced Casework LAM-1 Manufacturer: Nevamar Contact: (800) 638-4380 Ventura, Texas, and Orange County Sales Representative Pattern: TM 2001 Color: Ochre Tempura Location: Storage Room Casework Note: Provide fire rated substrate and adhesive to maintain or

obtain Class A fire rating where required by code. Provide radius exposed edges for casework.

LAM-2 Manufacturer: Wilsonart Contact: (800) 433-3222 Ventura, Texas, and Orange County Sales Representative Pattern: 7953-38 Color: Harvest Maple Finish: Fine Velvet Texture Location: Casework Note: Provide fire rated substrate and adhesive to maintain or

obtain Class A fire rating where required by code. Provide radius exposed edges for casework and bullnose edge at work counter

LAM-3 Manufacturer: Wilsonart Contact: (800) 433-3222 Ventura, Texas, and Orange County Sales Representative Pattern: 4861-07 Color: Gold Alchemy Finish: Textured Gloss Location: Casework Note: Provide fire rated substrate and adhesive to maintain or




LAM-4 Manufacturer: Wilsonart Contact: (800) 433-3222 Ventura, Texas, and Orange County Sales Representative Pattern: 7935K-07 Color: Shaker Cherry Finish: Textured Gloss Location: Casework and Elevator Wall Panels Note: Provide fire rated substrate and adhesive to maintain or

obtain Class A fire rating where required by code. Provide radius exposed edges for casework and bullnose edge at workcounter

LAM-5 Manufacturer: Wilsonart Contact: (800) 433-3222 Ventura, Texas, and Orange County Sales Representative Pattern: D30-60 Color: Natural Almond Finish: Matte Location: Plumbing Apron Note: Provide fire rated substrate and adhesive to maintain or


LAM-6 Manufacturer: Wilsonart Contact: (800) 433-3222 Ventura, Texas, and Orange County Sales Representative Pattern: 7919-38 Color: Amber Cherry Finish: Premium Location: Casework at 2

nd Floor

Note: Provide fire rated substrate and adhesive to maintain or obtain Class A fire rating where required by code. Provide radius exposed edges for casework.

B. Tackable Surface Material TB-1 Manufacturer: Pallas Textiles Contact: (800) 454-9796 Ventura and Orange County Sales Representatives Pattern: Carte Blanche Collection New Twist Color: Dreamy 28.056.041 Finish/Width: 84% Recycled Polyester 16% Polyester with Acrylic Backing Location: Work Area counters between worksurface and overhead Note: Fabric wrapped Homosote board butt jointed panels with seamless fabric application over top. Provide backing on fabric



C. Solid Surface Material SSM-1 Manufacturer: Cambria Quartz Contact: (952) 944-1676 Ventura, Texas, and Orange County Sales Representative Color: Hyde Park 2150 Finish: Polished Size: or Thick ADA Sink: Solid Surface under counter mount LG Hi-Macs Color: Cream Location: Nurse Stations, Work Areas, Conference Room, Chapel Note: Provide with 1.5 bullnose or waterfall edge as noted in

details and elevations and 6H finger-coved backsplash. Provide bullnose edge at sink side.

SSM-2 Manufacturer: LG Hi-Macs Contact: (877) 353-1805 Ventura, Texas, and Orange County Sales Representative Pattern: Volcanics Color: Basil VG22 Finish: Satin Size: or Thick ADA Sink: Solid Surface under counter mount Color: Cream Location: Exam Room, Toilet Room, and Back of House Note: Provide with 1.5 waterfall edge as noted in details and

elevations and 6H finger-coved backsplash. Provide bullnose edge at sink side.

SSM-3 Manufacturer: Corian Contact: (800) 436-6072 Ventura, Texas, and Orange County Sales Representative Pattern: Cottage Lane Finish: Satin Size: or Thick Location: Window Sills Note: Provide with 1.5 waterfall edge as noted in details and


SSM-4 Manufacturer: Meganite Contact: (800) 533-3030 Ventura, Texas, and Orange County Sales Representative Pattern: Surfing Safari 419 Finish: Satin Size: or Thick ADA Sink: Solid Surface under counter mount Color: Corian Bone Location: Infusion BMT Countertop Note: Provide with 1.5 waterfall edge as noted in details and




D. Resin Panel (Section 08840)

RES-1 Manufacturer: Lumicor Contact: CPS/Garten Corporation (949) 455-1600 Ventura, Texas, and Orange County Sales Representative Pattern: Lumiclear Meadow/Sedona Crush Finish: Front: Gloss, Back: Matte Size: 48W x 96H x 3/4 thick Location: Reception Desk, Nurse Station Note: Provide with Fire Polished exposed edges. RES-2 Manufacturer: 3Form Contact: (800) 726-0126 Ventura, Texas, and Orange County Sales Representative Pattern: Varia Ecoresin Hush Color: Natural Finish: Front: Sandstone, Back: Sandstone Size: 48W x 96H x 3/8 thick Location: Infusion Bays Note: Provide with Fire Polished exposed edges. E. Metal (Section 06402, 14240, 05700) MTL-1 Manufacturer: Fryreglet Contact: (800) 237-9773 Ventura, Texas, and Orange County Sales Representative Pattern: Reveal Channel Screed DCS-50-50 Finish: Satin Anodized Aluminum Size: x , 2 x , 1 x Location: Reveals Note: As noted in Elevations. MTL-2 Pattern: Flat Stock Aluminum Finish: Brushed Aluminum Size: W Location: Reveals MTL-3 Manufacturer: Moz Metal Contact: (510) 632-0853 And Orange County Sales Representative Pattern: Fog Finish: Dura Film - Satin Color: Clear Location: Column Covers Note: As noted in Elevations MTL-4 Manufacturer: Gage Contact: (415) 541-0969 Ventura, Texas, and Orange County Sales Representative Pattern: GC123 Vertical Surfacing Finish: Bronze (BZ) Location: Chapel Note: As noted in Elevations



SS-1 Manufacturer: Per Elevator Manufacturer Finish: Stainless Steel #4 Finish Location: Elevator Control Panel, Ceiling, Base and Doors F. Moulding (Section 06402) CHR-1 Manufacturer: Spectrim Contact: Adam Clark (800) 437-0557 Style: TCR-311 Medium Color: 17 Natural Cherry Size: D x 3 H Location: Transition at the top of the Wainscot (High Impact

Wallcovering) in Patient Care Areas per Finish Plan. Note: Height of chair rail to be coordinated with height of casework,

windowsills and backsplash. Film to be applied to a non-combustible surface to obtain Class A fire rating.

G. Wood WD-1 Manufacturer: Custom Wood Work Type: Solid Maple Wood Finish: Stained to match LAM-6 Location: Infusion Bay Screens Notes: See Elevations and Details for additional information. 1.03 GLAZING (Section 08816)

A. Glazing

GL-1 Manufacturer: Ultraglass Contact: (800) 777-2332 Ventura, Texas, and Orange County Sales Representative Pattern: Swirl Size: See Elevations Location: Door/Side Light, Screen Note: Glass panel. Provide with sealed polished exposed edges,

pattern to be vertical. GL-2 Manufacturer: Skyline Design Contact: (888) 278-4660 Ventura, Texas, and Orange County Sales Representative

Pattern: To match H. Wildflower 1D Henry Domke Image Size: See Elevation Thickness: 1/2 thick Location: Feature Wall First Floor Waiting

Note: Provide with Polished Exposed Edges. Digital Image to be protected between two layers of glass. Provide with 1 diam. stand-offs in anodized aluminum finish. Deduct Alternate: Provide Type II Digitized Wall Covering Mural



GL-3 Manufacturer: Photomation Contact: (714) 236-2121 Image: To match Henry Domke Orchard Grass 8606 Size: See Elevation Thickness: 1/2 thick Location:

Note: Provide with Polished Exposed Edges. Digital Image on slick to be protected between two layers of glass. See elevations and details for more information.

Deduct Alternate: Provide Type II Digitized Wall Covering Mural GL-4 Manufacturer: Nathan Allan Glass Studios Contact: (269) 767-7534 Image: Stax Flex Size: See Elevation Thickness: 1.5 Location: Feature Wall Note: Polish all exposed edges

GL-5 Manufacturer: Art Glass Contact: Image: To be determined Size: See Elevation Thickness: TBD Location: Chapel

1.04 TILE (Section 09300) A. Porcelain Paver Tile PPT-1 Manufacturer: Arizona Tile (Not Used) Contact: (818) 742-4750 Ventura, Texas, and Orange County Sales Representative Pattern: Misingi Color: Teka Size: 5 x 32 Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 35 Chaparal Location: Not Used Note: Provide minimal grout joint no greater than 1/16

and all required base and trim.

PPT-2 Manufacturer: Crossville Contact: (931) 484-2110 Ventura, Texas, and Orange County Sales Representative Pattern: Bluestone AV201 Color: Colorado Buff Finish: Honed Size: 6x24, 12x12, 12x24, 24x24 Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 145 Light Smoke Location: Field Floor Tile Note: Provide minimal grout joint no greater than 1/16

and all required base and trim. See floor pattern plan for random pattern installation.



PPT-3 Manufacturer: Dal TIle Contact: (310) 453-9112 Ventura, Texas, and Orange County Sales Representative Pattern: City View CY04 Color: Downtown Night Size: 12x12 Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 185 New Taupe Location: Toilet Room Floor Tile Note: Provide minimal grout joint no greater than 1/16

and all required base and trim. PPT-4 Manufacturer: Dal Tile Contact: (310) 453-9112 Ventura, Texas, and Orange County Sales Representative Pattern: Monticito Color: Crema MI20 Size: 12 x 24 Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 122 Linen Location: Toilet Room Wall Tile Note: Provide minimal grout joint no greater than 1/16

and all required base and trim. Deduct alternate: Provide 54 wainscot all walls except shower walls

PPT-5 Manufacturer: Tileshop (Not Used) Contact: (818) 994-9586 Ventura, Texas, and Orange County Sales Representative Pattern: Campogalliano - Strand Color: Beige CGSDBE Size: 12 x 24 Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 382 Bone Location: Not Used Note: Provide minimal grout joint no greater than 1/16

and all required base and trim.

PPT-6 Manufacturer: Crossville Contact: (931) 484-2110 Ventura, Texas, and Orange County Sales Representative Pattern: Bluestone AV201 Color: Colorado Buff Finish: Honed Size: 12x12 Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 145 Light Smoke Location: Elevator Cab Floor Tile Note: Provide minimal grout joint no greater than 1/16

and all required base and trim. See Floor Pattern Plan.



PPT-7 Manufacturer: Crossville Contact: (931) 484-2110 Ventura, Texas, and Orange County Sales Representative Pattern: Bluestone AV201 Color: Colorado Buff Finish: Honed/Unpolished Size: (Mesh Mounted) Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 145 Light Smoke Location: Ramps Note: Must comply with coefficient requirements for a ramp.

PPT-8 Manufacturer: Longust Contact: Julie Duenas Whalen (800) 352-0521 Pattern: Casa Dolce Casa 19 Tohidea A,B Color: Hyde Park Todi Finish: Matte Size: 15 x 31 Epoxy Grout: Custom Building Products 100% Epoxy Grout Color 380 Haystack Location: Womens Center Reception, Feature Wall B. Porcelain Tile Base

PTB-1 Manufacturer: Dal Tile Contact: Donna Apcar (310) 453-9112 Ventura, Texas, and Orange County Sales Representative Pattern: Monticito S-3639T Cove Base Color: Crema MI20

Size: 6 x 12 Cove Base Epoxy Grout: Custom Building Products 100% Epoxy Grout

Color: 122 Linen Location: Where PPT-4 is used.

Note: Provide minimal grout joint no greater than 1/16 Face of finish to be flush with adjacent finish. Provide with all

required trim pieces. Cut bullnose edge to allow for wall tile to be stacked as required.

C. Glass Tile

GT-1 Manufacturer: Stone and Pewter Contact: (415) 367-5616 Ventura, Texas, and Orange County Sales Representative Pattern: Tozen Mosaic

Color: Strontium Natural Size: 1x1 Mosaic

Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 311 Moss Location: Casework and Feature Wall Accent Note: Provide minimal grout joint no greater than 1/16.



GT-2 Manufacturer: Stone and Pewter Contact: (415) 367-5616 Ventura, Texas, and Orange County Sales Representative Pattern: Sumi-e Tresse

Color: Music Silk Size: Tresse Mosaic x 1, 1 x 4

Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 122 Linen Location: Toilet Room Accent Note: Provide minimal grout joint no greater than preset mosaic spacing. GT-3 Manufacturer: Stone and Pewter Contact: (415) 367-5616 Ventura, Texas, and Orange County Sales Representative Pattern: Sumi-e Japonaise

Color: Music Silk Size: Japonaise Mosaic x 1, 1 x 1

Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 122 Linen Location: Toilet Room Accent Note: Provide minimal grout joint no greater than preset mosaic spacing. D. Natural Stone (Section 09751)

NS-1 Manufacturer: Arizona Tile Contact: (818) 742-4750

Ventura, Texas, and Orange County Sales Representative Style: Granite Slab Finish: Polished Size: Thick Color: Seafoam Green ADA Sink: Corian Color Bone Location: Reception Countertop Note: Provide with 1 eased edge. See elevations and details. NS-2 Manufacturer: Arizona Tile

Contact: (818) 742-4750 Ventura, Texas, and Orange County Sales Representative Style: Stackstone Mosaic Color: Golden Gate Size: 11.75 x 11.75 Stackstone Mesh

Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 145 Light Smoke

Location: Feature Wall Accent Note: See Elevations and Details.



NS-3 Manufacturer: Stone Panels

Contact: (469) 635-5000 Ventura, Texas, and Orange County Sales Representative Style: Cenia A Finish: Honed Size; Per Elevation

Location: Entry Vestibule Note: See Elevations and Details. Pending Exterior Confirmation NS-4 Manufacturer: Dal Tile

Contact: Donna Apcar (310) 453-9112 Ventura, Texas, and Orange County Sales Representative Style: Crema Marfil Slab Finish: Honed Epoxy Grout: Custom Building Products 100% Epoxy Grout

Color: 122 Linen Location: Ledge Note: See Elevations and Details.

E. Wood Tile WT-1 Manufacturer: Stone and Pewter (Not Used)

Contact: (415) 367-5616 Ventura, Texas, and Orange County Sales Representative Style: Falling Water Color: Amberwood Size: 12 x 12 Mesh Mosaic

Epoxy Grout: Laticrete 100% Epoxy Grout Color: 55 Tawny

Location: Not Used Note: Grout size to match preset mosaic spacing.

F. Ceramic Tile CT-1 Manufacturer: Dal Tile

Contact: Donna Apcar (310) 453-9112 Ventura, Texas, and Orange County Sales Representative Style: K165 Color: Almond Size: 4 x 4

Epoxy Grout: Custom Building Products 100% Epoxy Grout Color: 122 Linen

Location: Utility Room Wet Wall



1.05 ACOUSTIC TREATMENT (Section 09511) A. Acoustic Ceiling Tile ACT-1 Manufacturer: USG Contact: (800) 950-3839 Ventura, Texas, and Orange County Sales Representative Pattern: Olympia Micro Tegular Color: White Size: 2 x 2, 2 x 4 Grid System: 15/16, Suprafine Heavy Duty, Color: White; Provide all necessary trim Location: General Ceiling Tile

ACT-2 Manufacturer: USG Contact: (800) 950-3839 Ventura, Texas, and Orange County Sales Representative Pattern: Clean Room Clima Plus Edge Detail: Square Lay-In Color: White

Size: 24 x 24 x 5/8 or 24 x 48 x 5/8 Grid System: 15/16 Prelude Heavy Duty System Exposed Tee Grid Color:

White. Provide all necessary trim pieces. Location: Wet Environments, Sterile Environments, Utility Rooms where

required by code 1.06 SPECIAL CEILING SURFACES (Section 09545) A. Ceiling Transparency

TRN-1 Manufacturer: Sky Factory Contact: (866) 759-3228

Ventura, Texas, and Orange County Sales Representative Image: 6eo_md04 Size: Coordinate with existing fixture location Location: Gamma Knife Note: Must use Sky Factory light fixture, which is to be on dimmers. Image orientation to be coordinated with

patient orientation. TRN-2 Manufacturer: Sky Factory

Contact: (866) 759-3228 Ventura, Texas, and Orange County Sales Representative Image: 4ex

Size: Coordinate with existing fixture location Location: Pet Scan Note: Must use Sky Factory light fixture, which is to be on dimmers. Image orientation to be coordinated with

patient orientation.




Ventura, Texas, and Orange County Sales Representative Image: 4fi

Size: Coordinate with existing fixture location Location: Lin AC Note: Must use Sky Factory light fixture, which is to be on dimmers. Image orientation to be coordinated with


TRN-4 Manufacturer: Sky Factory

Contact: (866) 759-3228 Ventura, Texas, and Orange County Sales Representative Image: 6bh_01

Size: Coordinate with existing fixture location Location: Vault Note: Must use Sky Factory light fixture, which is to be on dimmers. Image orientation to be coordinated with


Contact: (866) 759-3228 Ventura, Texas, and Orange County Sales Representative Image: 00s06

Size: Coordinate with existing fixture location Location: CT Note: Must use Sky Factory light fixture, which is to be on dimmers. Image orientation to be coordinated with



Contact: (866) 759-3228 Ventura, Texas, and Orange County Sales Representative Image: 3cdA

Size: Coordinate with existing fixture location Location: Patient Holding Note: Must use Sky Factory light fixture, which is to be on dimmers. Image orientation to be coordinated with


Contact: (866) 759-3228 Ventura, Texas, and Orange County Sales Representative Image: 4gn

Size: Coordinate with existing fixture location Location: Bone Density Note: Must use Sky Factory light fixture, which is to be on dimmers. Image orientation to be coordinated with





Ventura, Texas, and Orange County Sales Representative Image: 6tt_md01

Size: Coordinate with existing fixture location Location: Ultrasound Note: Must use Sky Factory light fixture, which is to be on dimmers. Image orientation to be coordinated with



Contact: (866) 759-3228 Ventura, Texas, and Orange County Sales Representative Image: 6tk

Size: Coordinate with existing fixture location Location: Ultrasound Note: Must use Sky Factory light fixture, which is to be on

dimmers. Image orientation to be coordinated with patient orientation.

1.07 RESILIENT FLOORING (Section 09651) A. Resilient Tile Flooring RTF-1 Manufacturer: Armstrong Flooring Contact: (877) 276-7876 Ventura, Texas, and Orange County Sales Representative Pattern: Natural Creations Earthcuts Color: Durango Beige TP508 Size: 16 x 16 Adhesive: Per SJH Standards and Manufacturers Recommendation Location: Field Resilient Floor Tile Note: See Floor Pattern Plans. Prepare sub-floor per

SJH Standards. Must have Square Edges.

RTF-2 Manufacturer: Armstrong Flooring Contact: (877) 276-7876 Ventura, Texas, and Orange County Sales Representative Pattern: Natural Creations Mystix Color: Kinderloy Bronze Patina TP707 Size: 12 x 24 Adhesive: Per SJH Standards and Manufacturers Recommendation Location: Accent Resilient Floor Tile Note: See Floor Pattern Plans. Prepare sub-floor per

SJH Standards. Must have Square Edges. Vine to be laser cut @ Factory and standard inlay template is to be provided to the field installer



RTF-3 Manufacturer: Armstrong Flooring Contact: (877) 276-7876 Ventura, Texas, and Orange County Sales Representative Pattern: Natural Creations Earthcuts Color: Rock Solid Sandstone TP549 Size: 18 x 18 Adhesive: Per SJH Standards and Manufacturers Recommendation Location: Accent Resilient Floor Tile Note: See Floor Pattern Plans. Prepare sub-floor per


RTF-4 Manufacturer: Armstrong Flooring Contact: (877) 276-7876 Ventura, Texas, and Orange County Sales Representative Pattern: Natural Creations ArborArt Color: Alder Mid TP018 Size: 4 x 36 Adhesive: Per SJH Standards and Manufacturers Recommendation Location: Field and Accent Resilient Floor Tile Note: See Floor Pattern Plans. Prepare sub-floor per

SJH Standards. Must have Square Edges. RTF-5 Manufacturer: Armstrong Flooring Contact: (877) 276-7876 Ventura, Texas, and Orange County Sales Representative Pattern: Natural Creations ArborArt Color: Walnut Medium TP020 Size: 4 x 36 Adhesive: Per SJH Standards and Manufacturers Recommendation Location: Accent Resilient Floor Tile Note: See Floor Pattern Plans. Prepare sub-floor per


RTF-6 Manufacturer: Armstrong Flooring Contact: (877) 276-7876 Ventura, Texas, and Orange County Sales Representative Pattern: Natural Creations Arbour Art Color: TP010 Wild Cherry Medium Size: 4 x 36 Adhesive: Per SJH Standards and Manufacturers Recommendation Location: Field and Accent Resilient Floor Tile Note: See Floor Pattern Plans. Prepare sub-floor per

SJH Standards. Must have Square Edges.



1.08 SHEET FLOORING (Section 09652) (For Reference Only If Needed) A. Linoleum Seamless Sheet Flooring LIN-1 Manufacturer: Forbo Contact: (800) 342-0604 Ventura, Texas, and Orange County Sales Representative Pattern: Marmoleum Real Color: 3120 Rosato Finish: Top Shield Size: 79W x 2.5mm Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Field Linoleum Floor LIN-2 Manufacturer: Forbo Contact: (800) 342-0604 Ventura, Texas, and Orange County Sales Representative Pattern: Marmoleum Striato Color: 5229 Fresh Walnut Finish: Top Shield Size: 79W x 2.5mm Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Accent Linoleum Floor LIN-3 Manufacturer: Forbo Contact: (800) 342-0604 Ventura, Texas, and Orange County Sales Representative Pattern: Marmoleum Real Color: 2707 Barley Finish: Top Shield Size: 79W x 2.5mm Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Accent Linoleum Floor LIN-4 Manufacturer: Forbo Contact: (800) 342-0604 Ventura, Texas, and Orange County Sales Representative Pattern: Marmoleum Real Color: 3234 Forest Ground Finish: Top Shield Size: 79W x 2.5mm Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Accent Linoleum Floor



LIN-5 Manufacturer: Forbo Contact: (800) 342-0604 Ventura, Texas, and Orange County Sales Representative Pattern: Marmoleum Fresco Color: 3876 Camel Finish: Top Shield Size: 79W x 2.5mm Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Accent Linoleum Floor

B. Seamless Sheet Vinyl SMV-1 Manufacturer: Armstrong (877) 276-7876 Pattern: Rejuvenations Stone Run Color: Sidecar 34352 Bagel Size: 72W x 0.080 thk. Adhesive: Per SJH standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendations Location: Biopsy SMV-2 Manufacturer: Armstrong (877) 276-7876 Pattern: Rejuvenations Timberline Maple Color: 37351 Knock on Wood Size: 72W x 0.080 thk. Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Biopsy SMV-3 Manufacturer: Armstrong (877) 276-7876 Pattern: Rejuvenations Timberline Cherry Color: 37362 Ruddy Cheeks Size: 72W x 0.080 thk. Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Biopsy SMV-4 Manufacturer: Armstrong (877) 276-7876 Pattern: Rejuvenations Lithos Stone Color: 34330 Lithos Andesite Size: 72W x 0.080 thk. Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Biopsy



C. Rubber Seamless Flooring RUB-1 Manufacturer: Nora Systems, Inc. Contact: (800) 336-5096 Ventura, Texas, and Orange County Sales Representative Pattern: Noraplan Environcare Color: Satin Wood 2785 Size: 3.0mm x 4-0W Welding Rod: To match per Manufacturers Recommendation Adhesive: Per CH Standards or Nora Plan NTX Location: Field Flooring Note: See Floor Pattern Plans. (Adhesive and Sub Floor

preparation per SJH and manufacturer specifications).

1.09 RESILIENT WALL BASE AND ACCESSORIES (Section 09653)

A. Resilient Base and Accessories RTS-1 Manufacturer: Johnsonite Contact: Ellen Wren (800) 899-8916 Ventura, Texas, and Orange County Sales Representative Pattern: Millwork Wallbase Diplomat MW-176-A Rubber Topset Base Color: 176 Brass Size: 4 H Adhesive: Per manufacturers recommendation Location: Field Resilient Base Throughout RTS-2 Manufacturer: Johnsonite Contact: Ellen Wren (800) 899-8916 Ventura, Texas, and Orange County Sales Representative Pattern: Traditional Top Set Rubber Wall Base Color: 49 Beige Size: 4 H Adhesive: Per manufacturers recommendation Location: Back of House Wall Base for future improvement. RTS-3 Manufacturer: Johnsonite or Burke Colonial Contact: Ellen Wren (800) 899-8916 Ventura, Texas, and Orange County Sales Representative Pattern: Millwork Emissary MW 49-P Color: Beige 49 Size: 4-1/2 H Adhesive: Per manufacturers recommendation Location: Infusion B. Transition Strip TS-1 Manufacturer: Schluter Contact: (800) 472-4588 Ventura, Texas, and Orange County Sales Representative Pattern: Shiene - As required per flooring condition Finish: Brushed Stainless Steel Size: Profile to be verified by Flooring Contractor Location: All flooring transition strips as required for various material

transitions. Note: Face of finish floor to be flush with one another



C. Self Cove Base SCB-1 Manufacturer: Forbo Contact: (800) 342-0604 Ventura, Texas, County Sales Representative Pattern: Marmoleum Color: To match adjacent floor Finish: Top Shield Size: 6H self cove base as required by code Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: Toilet Room Note: Provide with Aluminum Top Cap SCB-2 Manufacturer: Armstrong Contact: (877) 276-7876 Ventura, Texas, County Sales Representative Pattern: Rejuvenations Stone Run Color: To match adjacent floor Size: 4H or 6H self cove base as required by code Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: As noted in Room Finish Schedule. Note: Provide with Aluminum Top Cap SCB-3 Manufacturer: Nora Contact: (800) 336-5096 Ventura, Texas, County Sales Representative Pattern: Environcare Color: To match adjacent floor Size: 4H or 6H self cove base as required by code Adhesive: Per SJH Standards and Manufacturers Recommendation Welding Rod: To match per Manufacturers Recommendation Location: As noted in Room Finish Schedule. Note: Provide with Aluminum Top Cap

1.10 CARPET (Section 09680)

A. Carpet CPT-1 Manufacturer: Lees Carpet Contact: (800) 523-5647 Ventura, Texas, and Orange County Sales Representative Pattern: Ray of Sunshine GT127 Color: 635 Renewal Size: 24 x 24 Installation Method: Vertical Ashlar Pad: None (direct glue) Adhesive: Per SJH Standards and Manufacturers Recommendation. Weight: 26 oz. Yarn: Smartstrand Contract made with DuPont Sorona Triexta Location: Waiting, Reception Note: Face of insert carpet to be flush with adjacent floor finish.

Prepare sub-floor per SJH Standards.



CPT-2 Manufacturer: Lees Carpet Contact: (800) 523-5647 Ventura, Texas, and Orange County Sales Representative Pattern: First Day of Spring GT131 Color: 635 Renewal Size: 24 x 24 Installation Method: Vertical Ashlar Pad: None (direct glue) Adhesive: Per SJH Standards and Manufacturers Recommendation. Weight: 26 oz. Yarn: Smartstrand Contract made with DuPont Sorona Triexta Location: Offices, Dressing, Conference, Family Resource Center,

Consultation Note: Prepare sub-floor per SJH Standards. CPT-3 Manufacturer: Lees Carpet Contact: (800) 523-5647 Ventura, Texas, and Orange County Sales Representative Pattern: Endless Horizon GT130 Color: 635 Renewal Size: 24 x 24 Installation Method: Vertical Ashlar Pad: None (direct glue) Adhesive: Per SJH Standards and Manufacturers Recommendation. Weight: 26 oz. Yarn: Smartstrand Contract made with DuPont Sorona Triexta Location: Corridor, Sub Waiting, and Nurse Station Note: Face of insert carpet to be flush with adjacent floor finish.

Prepare sub-floor per SJH Standards.

CPT-4 Manufacturer: Karastan Contact: (800) 523-5647 Ventura, Texas, and Orange County Sales Representative Pattern: Sonic Cadence KC156 Color: 158 Interlude Size: 12W Pad: KC 156 Adhesive: Per SJH Standards and Manufacturers Recommendation. Weight: 32 oz. Yarn: Color Strand Solution Dyed Nylon Pattern Repeat 18W x 23L Location: Chapel Note: Face of insert carpet to be flush with adjacent floor finish. Prepare sub-floor per SJH Standards.



1.11 PAINTING (Section 09910) A. Interior Paint Eggshell Finish PTE-1 Manufacturer: Dunn Edwards Contact: (310) 367-6422 Ventura, Texas, and Orange County Sales Representative Color: Sand Castle DEC740 Finish: Eggshell Location: Field Wall Paint Throughout Note: Must have low VOC emissions and comply with current air

quality safety standards. PTE-2 Manufacturer: Benjamin Moore Contact: (888) 854-9889 Ventura, Texas, and Orange County Sales Representative Color: Saddle Tan 1124 Finish: Eggshell Location: Accent Wall Paint Note: Must have low VOC emissions and comply with current air

quality safety standards. PTE-3 Manufacturer: Dunn Edwards Contact: (310) 367-6422 Ventura, Texas, and Orange County Sales Representative Color: Northgate Green DE6235 Finish: Eggshell Location: Accent Wall Paint Note: Must have low VOC emissions and comply with current air

quality safety standards. PTE-4 Manufacturer: Dunn Edwards Contact: (310) 367-6422 Ventura, Texas, and Orange County Sales Representative Color: Graham Cracker DE6144 Finish: Eggshell Location: Reading Room above Wainscot Note: Must have low VOC emissions and comply with current air

quality safety standards. B. Interior Paint Semi-Gloss Finish PTS-1 Manufacturer: Dunn Edwards Contact: (310) 367-6422 Ventura, Texas, and Orange County Sales Representative Color: Babys Breath DEW342 Finish: Semi-gloss Location: Ceiling Note: Must have low VOC emissions and comply with current air

quality safety standards.



PTS-2 Manufacturer: Dunn Edwards Contact: (310) 367-6422 Ventura, Texas, and Orange County Sales Representative Color: Sandcastle DEC740 Finish: Semi-gloss Location: Field Wall Paint Note: Must have low VOC emissions and comply with current air

quality safety standards. PTS-3 Manufacturer: Scuffmaster or Equal Contact: (800) 898-0219 Ventura, Texas, and Orange County Sales Representative Color: Solid Metal SM9737 Finish: Semi-gloss Location: Accent Paint Note: Must have low VOC emissions and comply with current

air quality safety standards.

C. Interior Paint Flat Finish PTF-1 Manufacturer: Dunn Edwards Contact: (310) 367-6422 Ventura, Texas, and Orange County Sales Representative Color: Babys Breath DEC342 Finish: Flat Location: Field Ceiling Note: Must have low VOC emissions and comply with current air

quality safety standards. See Reflected Ceiling Plan. PTF-2 Manufacturer: Frazee Contact: (800) 826-9048 Ventura, Texas, and Orange County Sales Representative Color: 8184M Moselle Finish: Flat Location: Accent Soffit Note: Must have low VOC emissions and comply with current air quality safety standards. See Reflected Ceiling Plan. PTF-3 Manufacturer: Benjamin Moore Contact: (888) 854-9889 Ventura, Texas, and Orange County Sales Representative Color: Saddle Tan 1124 Finish: Flat Location: Accent Soffit Note: Must have low VOC emissions and comply with current air quality safety standards. See Reflected Ceiling Plan. PTF-4 Manufacturer: Dunn Edwards Contact: (310) 367-6422 Ventura, Texas, and Orange County Sales Representative Color: Almond Latte DE6143 Finish: Flat Location: Accent Soffit Note: Must have low VOC emissions and comply with current air

quality safety standards. See Reflected Ceiling Plan.



1.12 WALLCOVERING (Section 09720) A. Vinyl Wallcovering

VWC-1 Manufacturer: Trikes Contact: (800) 200-8120 Ventura, Texas, and Orange County Sales Representative Pattern: Lanark Code R2-CX-11 Color: Cache Size: 53/54W Content: 100% Recycled Polyester Pattern Repeat: N/A Location: Family Resource, Womens Dressing, Waiting 36H Wainscot at Reading Room

VWC-2 Manufacturer: Trikes Contact: (800) 200-8120 Ventura, Texas, and Orange County Sales Representative Pattern: Lanark Tableau L2-TA-17 Color: Irish Linen Size: 53/54W Content: Type II Vinyl Pattern Repeat: 26H, N/A V Location: Consult, Sub-Wait Accent, Registration, Mens

Waiting/Dressing, Hall

VWC-3 Manufacturer: Wolf Gordon Contact: (800) 347-0550 Ventura, Texas, and Orange County Sales Representative Pattern: Linnea Flower G8216391 Color: Esquise Size: 52W Content: Type II Vinyl Pattern Repeat: 52H, 24V Location: Womens Waiting, Adult Cancer Center and Womens

Dressing Room, Dressing Area

VWC-4 Manufacturer: Wolf Gordon Contact: (800) 347-0550 Ventura, Texas, and Orange County Sales Representative Pattern: Legacy G7104508 Color: Sorrel Size: 54W Content: Type II Vinyl Pattern Repeat: Random Location: Chapel, Family/Resource Center, Corridor Waiting

VWC-5 Manufacturer: Trikes Tower Wallcovering Contact: Jamalle French (818) 919-1680 Ventura, Texas, and Orange County Sales Representative Pattern: Trixie Color: Corn Silk TR-TR-14 Size: 54W Content: Type II Vinyl Location: Resource Center



1.13 IMPACT-RESISTANT WALL PROTECTION (Section 10265)

A. Corner Guards CG-1 Manufacturer: CS Acrovyn Contact: (626) 665-1321 Ventura, Texas, and Orange County Sales Representative Pattern: SSM-20 Color: 997 Irish Cream

Size: 2 x 2 Full Height Location: Back of House Note: Provide with all trim pieces and end caps. Corner Guards to

go to the base unless otherwise required by code. CG-2 Manufacturer: CS Acrovyn Contact: (626) 665-1321 Ventura, Texas, and Orange County Sales Representative Pattern: SMWS-20 Finish: #053 Honey Beech with Stainless Steel Guard Size: 2 3/4 x 2 3/4 Full Height Location: Patient and Public Areas Note: As noted on Room Finish Schedule and Architectural Plans.

Provide with all trim pieces and end caps. Corner Guards to go to the base unless otherwise required by code.

B. High Impact Wallcovering HIC-1 Manufacturer: Korogard Contact: (800) 935-9359 Ventura, Texas, and Orange County Sales Representative Pattern/Color: Orleans Goblet TP-R921-82 Size: 4 x 8 sheets, .030 thick Location: Corridors, Infusion, Exam and Precedure Note: To be railroaded. Provide silicone butt joint seams. Top of

wainscot to receive chair rail. Wainscot height per Wall Protection Plan.

HIC-2 Manufacturer: CS Acrovyn Contact: (626) 665-1321 Ventura, Texas, and Orange County Sales Representative Color: 997 Irish Cream Size: .040 thick Location: Back of House Note: To be railroaded. Provide with silicone butt joint seams. 48H

sheet to be installed at top of base. HIC-3 Manufacturer: Spectrim Contact: (800) 437-0557 Ventura, Texas, and Orange County Sales Representative Color: 08 Honduras Mahogany Size: .040 thick Location: Elevator Lobby, Waiting Note: Provide with Aluminum Reveals and silicone butt joint seams. See elevations and details.



C. Handrail HDR-1 Manufacturer: Per Elevator Manufacturer Style: Tube Handrail Size: 1 Diameter Finish: Stainless Steel Location: Elevator Cab HDR-2 Manufacturer: Viva Railing or Equal Contact: (972) 353-8482 Ventura, Texas, and Orange County Sales Representative Style: Fin Glass: Ultra Glass Rain (Deduct Alternate: Frosted Glass) Metal Stringer Finish: Brushed Stainless Top Rail, Handrail and Post Finish: Wood to match LAM-4 Location: Open Stair HDR-3 Manufacturer: Acrovyn Style: HRWS 6C Size: 3W x 5-1/4H Metal Finish: Stainless Bracket Wood: Honey Maple 004 Location: Ramp

1.14 FLOOR MATS AND FRAMES (Section 12484)

A. Floor Mats MAT-1 Manufacturer: Lees Carpet Contact: (800) 523-5647 Ventura, Texas, and Orange County Sales Representative Pattern: Tuff Stuff Step In Style GT066

Color: Woodland Brown 524 Size: 24 x 24 Installation Method: Brick Ashlar Pad: None (direct glue) Adhesive: Per SJH Standards and Manufacturers Recommendation. Weight: 32 oz. Yarn: Fortis Nylon Location: Entry Vestibule Note: Face of insert carpet to be flush with adjacent floor finish.

Prepare sub-floor per SJH Standards. Provide Schluter transition strip.



1.15 MISCELLANEOUS A. Decorative Light Fixtures (Section 16500) FIX-1 Manufacturer: Eureka Contact: CLS (818) 893-6599 x 1760 Ventura, Texas, and Orange County Sales Representative Style: 3211C-CHR-WH Sirrah wall mounted Fixture Finish: Chrome with White Glass Size: 21.25L x 5W x 3.05D. Lamping: Fluorescent Location: Toilet Room Vanity Light Note: UL Listed FIX-2 Manufacturer: Hubbardton Forge Contact: (802) 468-3090 Ventura, Texas, and Orange County Sales Representative Style: 135001D Finish: 82 Vintage Platinum Size: 16-116H x 5.5 Canopy Lamping: LED Location: Pendant Note: UL Listed FIX-3 Manufacturer: Hubbardton Forge Contact: (802) 468-3090 Ventura, Texas, and Orange County Sales Representative Pattern: Dune 204795 Finish: 17 Opaque Dark Smoke Glass Diffuser: White Art Size: 23.6H x 5.3W x 4D Lamping: Per Electrical Engineer Location: Consult Room, Corridor, Chapel, Conference Appearance

Sub Waiting Note: To be mounted 66 A.F.F. to center. UL Listed FIX-4 Manufacturer: Bruck Lighting Contact: Performance Lighting Systems (800) 382-3055 Ventura, Texas, and Orange County Sales Representative Style: Ciro LED Down Pendant Light Number/Finish: 222119mc/MP2 CO#35 Matte Chrome, White Fritted Glass Size: 3 5/8 Diam. x 8 3/4H with 12 1/2" stem and with 36" stem. Lamping: Per Electrical Engineer Location: Reception/Registration, Family Resource, Check-in Note: UL Listed. See Elevations for mounting heights. FIX-5 Manufacturer: Eureka Lighting Contact: CLS (818) 893-6599 x 176 Ventura, Texas, and Orange County Sales Representative Style: Sirach 3611C Finish: Satin Chrome (SC) with White Diffuser (WH) Size: 21.25H x 5W x 2.55Proj. Lamping: Per Electrical Engineer Location: Lin Accel. Wall Sconce Note: UL Listed. Center of fixture to be mounted 66 A.F.F.



FIX-6 Manufacturer: Hubbardton Forge Contact: (802) 468-3090 Ventura, Texas, and Orange County Sales Representative Pattern: 217653 Gallery Wall Sconce Finish: Glass: Decaf Acrylic Metal: 17 Opaque Dark Smoke Lamping: Per Electrical Engineer Size: 59.2H x 4.3W x 3.2 Projection ADA compliant Location: Gallery, Womens Waiting Note: UL Listed, Mount horizontally per Elevation. FIX-7 Manufacturer: Lithonia

Contact: (805) 642-7714 Ventura, Texas, and Orange County Sales Representative Style: VT Series 2VTL Finish: Matte Satin White Lamping: LED Per Electrical Engineer 3500K Size: 2 x 2 or 2 x 4 Location: General Ambient Lighting Note: UL Listed, Provide Dimmers in Reading Room

FIX-8 Manufacturer: Phillips Lightolier Contact: (800) 937-5483 Ventura, Texas, and Orange County Sales Representative Style: Vetro LED DA6A03 with double frosted opal glass ring Finish: Matte White Lamping: LED

Size: 5 1/8 6 1/4 Diam. Location: General Down Light Note: UL Listed FIX-9 Manufacturer: Pathway or Equal Contact: (860) 388-6881 Ventura, Texas, and Orange County Sales Representative Style: Park Avenue from Coventry Architectural Series Finish: Clear, Reflector: Aluminum, Flange: Matte White Size: 6Diam. Lamping: LED Location: Toilet Room Note: UL Listed. For Wet Locations FIX-10 Manufacturer: Hubbardton Forge Contact: (802) 468-3090 Ventura, Texas, and Orange County Sales Representative Pattern: 137901 Pendant (Aperture Linear Suspension Light) Finish: 17 Opaque Dark Smoke Lamping: Per Electrical Engineer Size: 37.3W x 27-76H x 5.3D Location: Gallery Note: UL Listed



FIX-11 Manufacturer: Bruck Lighting Contact: (800) 382-3055 Ventura, Texas, and Orange County Sales Representative Pattern: Ledra R 13573 Recessed Adjustable Head

Finish: Matte Chrome Lamping: LED 3000K Size: 2 1/4Dia x 1 3/8D, 1 aperture Location: Gallery Display Cabinet Note: UL Listed FIX-12 Manufacturer: Per Electrical Engineer Contact: Ventura, Texas, and Orange County Sales Representative Pattern: Cove Strip Light

Finish: White Lamping: LED Size: Location: Chapel Cross, Waiting Note: UL Listed FIX-13 Manufacturer: Per Electrical Engineer Contact: Ventura, Texas, and Orange County Sales Representative Pattern: LED Linear Strip Light

Finish: White Lamping: LED Size: Location: Note: UL Listed FIX-14 Manufacturer: Hubbardton Forge Contact: (802) 468-3090 Ventura, Texas, and Orange County Sales Representative Pattern: Forged Reed Sconce 205750 Finish: Opaque Dark Smoke #17, White Art Glass Lamping: Per Electrical Engineer Size: 12H x 9W x 4D Location: Mammo Exam Room Entry Note: UL Listed FIX-15 Manufacturer: Hubbardton Forge Contact: (802) 468-3090 Ventura, Texas, and Orange County Sales Representative Pattern: 18453 Finish: Dark Smoke 17 Spun Frost Glass Shade 66 Lamping: Per Electrical Engineer Size: 8 Diam. X 12H x 35.1 56.8L Location: Pendant @ Womens Subwaiting Note: UL Listed



FIX-16 Manufacturer: Focal Point Contact: (949) 622-3000 Ventura, Texas, and Orange County Sales Representative Pattern: Seem 4 Flush Linear Strip Finish: Matte White Lamping: Per Electrical Engineer Size: 4 Location: Wood Ceiling Note: UL Listed FIX-17 Manufacturer: Per electrical engineer Contact: Ventura, Texas, and Orange County Sales Representative Pattern: Adjustable Down Light Finish: Matte White Lamping: Per Electrical Engineer Size: Location: Note: UL Listed FIX-18 Manufacturer: Amerlux Contact: (281) 997-5400 Ventura, Texas, and Orange County Sales Representative Pattern: Drama LED Wall Grazer Finish: Matte White Lamping: Per Electrical Engineer Size: 4 W x 3 5/8 H x 8 Location: Feature Wall Note: UL Listed, to be pig tailed B. Window Treatment (Section 12494)

SHD-1 Manufacturer: MechoShade Systems Contact: (718) 729-2020 Ventura, Texas, and Orange County Sales Representative Pattern: 6000 Series Twill Weave Roller Shade System Finish/Color: 6004 Sand Openness Factor: 3% with Black out roller shade behind Pattern: 7100-P04

White Bone Location: Exterior Windows

Note: Continuous Clutch System VAL-1 Manufacturer: Lumicor

Contact: (949) 455-1600 Ventura, Texas, and Orange County Sales Representative Pattern: Custom Valance Finish/Color: Pearl Milan Wood Trim: To match LAM-2 Resin Sheet Size: 48 x 96 x Valance Size: 10H x 9D Width to be field verified with existing window

conditions. Valance to conceal attachment hardware Location: Patient Areas unless drapery pockets are provided

Note: See Details for additional information



C. Cubicle Curtain CUB-1 Manufacturer: Carnegie Contact: (800) 727-6770 Ventura, Texas, and Orange County Sales Representative Pattern: Affirmation II 4458 Color: 24 Content: 100% Post Consumer Recycled Polyester Width: 72W Repeat: 27.5V, 37.75H Location: Patient Care Areas Note: Provide with grommets 6 O.C. and 18 mesh Color: Beige

D. Murals MUR-1 Manufacturer: Photomation

Contact: Karen Adkins (714) 236-1826 Image: Henry Domke Indian Grass 13548 Size: See Accent Wall Finish Plan Content: Type II Vinyl Location: Vault Note: Confirm image numbers with vendor

MUR-2 Manufacturer: Photomation Contact: Karen Adkins (714) 236-1826

Image: Henry Domke Orchard Grass 8606 Size: See Accent Wall Finish Plan Content: Type II Vinyl Location: Pet Scan Note: Confirm image numbers with vendor MUR-3 Manufacturer: Photomation Contact: Karen Adkins (714) 236-1826

Image: Henry Domke Big Bluestream 7885 Size: See Accent Wall Finish Plan Content: Type II Vinyl Location: Gamma Knife

Note: Confirm image numbers with vendor


Image: Pending Client Approval Size: See Accent Wall Finish Plan Content: Type II Vinyl Location: Lin Accel Note: Confirm image numbers with vendor


Image: Pending Client Approval Size: See Accent Wall Finish Plan Content: Type II Vinyl Location: HDR Note: Confirm image numbers with vendor



E. Signage SGN-1 Manufacturer: Photomation Contact: Karen Adkins (714) 236-1826 Style: Pin Mounted Raised Lettering Font: Apple Chancery Finish: Brushed Stainless Steel Finish Size: 2 H Location: Feature Wall Note: See Elevations.

F. Mirror (Section 10801) MIR-1 Manufacturer: American Specialties Contact: (914) 476-9000 Pattern: 8287 with 1 bevel Size: Per elevations Location: Toilet Rooms

H. Specialty Ceilings MC-1 Manufacturer: Ceilings Plus Contact: (800) 822-3411 Ventura, Texas, and Orange County Sales Representative Pattern: Illusions Micro Perforated .040 Aluminum Finish: Arboreal Annigre Location: Nurse Station, Reception Note: Suspended ceiling to be provided with acoustic backer.

Provide with all necessary hardware and trim pieces as shown in details. Provide with perimeter edging. Trim finish to

match G. WC-1 Manufacturer: Armstrong or Ceilings Plus Contact: Ventura, Texas, and Orange County Sales Representative Pattern: Barz Linear Wood Suspended Ceiling System Size: 2 x 4 with 4 spacing Finish: Annigre Location: Entry Gallery Note: Non-combustible aluminum

Provide with all necessary hardware and trim pieces as shown in details. Provide with perimeter edging. Trim finish to match. Black felt above.

H. Lockers LKR-1 Manufacturer: Republic

Contact: (800) 477-1255 Pattern: Standard Metal Lockers Color: 52 Canyon Size: Per Architectural Specifications Finish/Type: Standard Powdercoat Finish on all parts of Locker Standard ventilation in door panel only Standard handle type, uses lock by Owner Location: Staff Lounge/Locker Note: See Architectural Details for additional information. Configuration per user group requirements



I. Sliding Door DR-1 Manufacturer: OH Line or Equal Contact: (310) 327-4630 Ventura, Texas, and Orange County Sales Representative Pattern: S-21, S-14 Sliding Shoji Screen Finish: Lumicor Colorways Desert Crush AC841.102LL Wood Finish: To match LAM-2 Size: Per architectural plans

Location: Admitting Note: Ceiling mounted track with floor glide

DR-1 Manufacturer: 3 Form (Alternate) Contact: (310) 824-3396 Ventura, Texas, and Orange County Sales Representative Pattern: 100.08 Header Mount Sliding Door with Stiffener Handle Finish: Hush Natural Sandstone Front and Back Wood Finish: To match LAM-2 Size: Per architectural plans

Location: Admitting Note: Ceiling mounted track with floor glide, polished exposed edges

J. Slat Wall System SLT-1 Manufacturer: Palay Display Industries or equal Contact: (800)-437-5377 Pattern: Slat Wall System Laminate Finish: LAM-3 Metal Finish: Anodized Aluminum Accessories: Per User Requirements Size: 8-0 x 10-0 Location: Display, Style, Fitting

SLT-2 Manufacturer: B&N Industries Contact: (800) 350-4127 Style: Mini Pog System with laminated panel and iconic panel- Helsinki Finish: Frosted Acrylic, Custom laminate to match LAM-5, Iconic panel Helsinki to be painted PTE-1 Location: Gallery Display Note: System components to be coordinated with user requirements.



General Notes:

1. Adhere to the SJH Finish and Construction Standards dated July 2006, including, but not limited to, the Casework Details, Lighting, Signage and Ergonomic Standards. 2. All supply and return grill finishes to match finish of adjacent surface where it will be installed. 3. Hollow metal doors and frames to be painted with semi-gloss paint, color to match adjacent wall. 4. Door vision panels are to be painted to match the door in a semi-gloss finish unless noted otherwise. 5. Wood doors to be Acrovyn Finish: Chameleon Collection 373 Amber Cherry 6. Solid surface countertop to have a 1-1/2" Bullnose or Waterfall edge and 4"H backsplash unless noted otherwise. Provide 6"H backsplash at Wet Areas unless noted otherwise. Omit backsplash where tack board occurs. If budget permits full height backsplashes are preferred. 7. All casework edges to be radius, vertically and horizontally. 8. When a countertop height drops the backsplash should remain the same height. 9. Provide fabric wrapped homosote board at all Work Areas between countertop and overhead. Backsplash is not required unless noted otherwise. 10. Provide under cabinet task lights at all Work Areas. 11. If countertop at sink is solid surface material, adjacent countertop to be the same finish unless noted otherwise. 12. Countertop where articulating keyboard tray occurs to be flush and level without depression. 13. Plastic laminate countertop wherein a knee space is provided is to have 1-1/2" bullnose edge for ergonomic compliance (on the User side). Bullnose to be wood at plastic laminate countertops and solid surface at solid surface countertops. Wood bullnose edge to be Natural Maple with a stain to match countertop finish unless noted otherwise. 14. All doors in high traffic areas to have full height stainless steel vertical U channel on both hinge and strike sides of door. Door frames to have 48"H stainless steel protectors (see Architectural Detail as required). Kick plates to be provided on high traffic doors per SJH Standards. 15. Casework to have plastic laminate soffits above the overhead cabinets. 16. Schluter transition strips are to be provided at all floor material transitions including Toilet Rooms unless solid surface thresholds are required. Transition where same finishes meet in different color or pattern do not require transition strip unless noted otherwise. 17. All resilient flooring is to be installed with adhesive per SJH Standards and guaranteed against bubbling due to, but not limited to, moisture and heavy rolling traffic. 18. Elevator Cab finishes as noted in the Room Finish Schedule. 19. All Linoleum flooring to be provided with Top Shield finish. 20. Toilet Room down light fixture to be Pathway Coventry Architectural Series Park Avenue unless noted otherwise. Provide with a lens in all Wet Areas, and without in all Dry Areas. 21. All carpet backing is to include a moisture barrier and is to have the appropriate seams to prohibit moisture from penetrating the surface. 22. Integral Pendaflex rails are to be provided in all casework file drawers. 23. Toilet Room mirrors to have 1 beveled edge and to be frameless. 24. High Impact Wallcovering to have CHR-1 chair rail (approximately 36"H) that aligns and is coordinated with the bottom of headwall and/or backsplash and windowsill. (see specifications for CHR-1). 25. Concealed sprinkler heads to be white unless they are located in the wood ceiling or accent soffits which are to be chrome. 26. Drywall pony walls at Nurse Stations are not allowed. 27. All window sills to be solid surface material, Color: Corian - Cottage Lane SSM-3 28. Under counter refrigerators to have plastic laminate front face panels and are to fit under the ADA compliant countertop. Plastic laminate fronts to match adjacent casework. 29. All Patient and Public Area sinks are to be solid surface material ADA Compliant under



counter mount as noted in specifications. Stainless Steel or Porcelain sinks can be utilized in Utility Rooms. 30. Access panels to be painted to match adjacent surface semi-gloss finish. 31. Exit devise finish to be satin chrome with green text. 32. Devise and cover plates to be white unless code requires otherwise. 33. Grommets to be linear slots. For location and quantity follow Architectural drawings.

End of Section