PROGRAMMER Willem PRO 2 2018-05-16آ  Erasing 7 Erasing 1.) . To erase individual system, choose items

  • View
    14

  • Download
    1

Embed Size (px)

Text of PROGRAMMER Willem PRO 2 2018-05-16آ  Erasing 7 Erasing 1.) . To erase individual system, choose...

  • CHIP SERVICINGCHIP SERVICING BIOS TUNINGBIOS TUNING HOUSEHOLDS SERVICINGHOUSEHOLDS SERVICING

    PROGRAMMINGPROGRAMMING

    WILLEM PRO 2 ONLY INTELLIGENT PROGRAMMING

    PROGRAMMERPROGRAMMER

    Willem PRO 2Willem PRO 2 VERSIONVERSIONZIFZIF

  • WILLEM is the most popular programmer available on the market.

    This programmer can be successfully used for: RTV services, BIOS updates in computer services, repairs of computer boards (damaged by failed BIOS updates) and also in situations where programming of memory or microprocessor is required.

    The programmer is built on two-sided laminate with metal-plated

    openings, solder mask complete with description of components.

    -To supply the programmer, a power supply feeder cable with 12V direct current voltage is recommended.

    -Finished device is to be connected to PC.

    -Connection between programmer and PC is secured by LPT cable (complete with all conductors).

    -Programming is performed with a Willem programmer control software recorded on a CD.

    --This device is able to read (feed into a PC), delete (erase from the system) or record (re-programme anew) individual memory according to user's requirements.

    What is Willem PRO 2?11

    What is Willem PRO 2?

  • LPT cable (option)

    CD

    USB Cable (option)

    12V power supply feeder cable

    As seen from below

    As seen from above

    Contents of the package

    Accessories:

    Programmer Willem PRO 2

    Contents of the package22

  • 22 C

    o n te

    n ts

    o f

    th e p

    a c k a

    g e

    V P

    P V

    C C

    J H

    4 V

    P P

    J H

    3 J

    U M

    P E

    R

    J P

    7

    J P

    8

    J P

    6

    P O

    W E

    R

    H U

    B O

    N

  • K A

    B E

    L L

    P T

    1 -1

    te l.

    6 9

    4 -5

    6 2

    -9 7

    3

    Z A

    S IL

    A N

    IE 9

    -1 2

    V L

    U B

    U S

    B .

    W yb

    ó r

    n a

    p ię

    ci a

    p

    ro g

    ra m

    u ją

    ce g

    o V

    P P

    W y b

    ó r

    n a

    p ię

    ci a

    V C

    C (

    J P

    8 )

    W y b

    ó r

    w e

    rs ji

    N O

    R M

    A L F

    ir m

    w a

    re H

    U B

    - O

    F F

    F ir m

    w a

    re H

    U B

    - O

    N

    U ży

    w a

    n ie

    a d

    a p

    te ra

    F

    ir m

    w a

    re H

    U B

    3 .3

    V

    (P L

    C C

    -H U

    B )

    5 .0

    V

    J H

    4 V

    P P

    JH 3

    J U

    M P

    E R

    D E

    F A

    U LT

    5 .6

    V 1

    2 .5

    V 98 D

    2 P

    R O

    2

    1 5

    V 2

    1 V

    2 5

    V

    W IL

    L E

    M P

    R O

    F E

    S S

    IO N

    A L

    2

    W W

    W .P

    R O

    G R

    A M

    A T

    O R

    Y .C

    O MJ

    7 J

    6 J

    7 J

    6 J

    7 J

    6 J

    7 J

    6

    22 C

    o n te

    n ts

    o f

    th e p

    a c k a

    g e

  • 1.Remove programmer from the box and position it so the LPT connector is on the left side. 2.Connect LPT cable to PC and then to programmer (Fig. 1.1) Red LED light indicating power supply is on (marked by yellow arrow).

    Once the power supply has been connected, the power supply signalling LED light is stronger, and additionally yellow LED (VCC) and green LED (VPP) are on.

    Warning Only one power supply source can be used! In case a voltage adjustable power supply feeder cable is used, move the switch onto 12V.

    Next, connect power supply. Choose USB cable (Fig 1.2) or 12V power supply feeder cable (Fig. 1.3).

    Connecting programmer to PC

    VPP VCC

    JH4 VPP JH3 JUMPER

    JP7

    JP8

    JP6

    POWER

    HUB ON

    VPP VCC

    JH4 VPP JH3 JUMPER

    JP7

    JP8

    JP6

    POWER

    HUB ON

    Power supply through USB cable

    Power supply through 12V power supply feeder cable

    Connecting programmer to PC

    VPP VCC

    JH4 VPP JH3 JUMPER

    JP7

    JP8

    JP6

    POWER

    HUB ON

    33

    Fig 1.1

  • Installation of software

    1.) Close all application running on PC.

    2.) Insert CD with WILLEM software into CD drive

    3.)

    4.)

    5.)

    6.)

    Open My Computer => CD drive

    Copy entire "willem" catalogue to C drive

    Unpack "port.zip" file (port zip file is an automatically unpacking archive and does not require extra programme such as WINRAR or WINZIP)

    Enter "User_Port" catalogue. Copy "UserPorts.sys" file to C:\WINDOWS\system32\drivers catalogue (Fig. 1.4)

    Installation of software44

  • 7.Open "User_Port" catalogue. Start "UserPort.exe". Set the parameters as shown on Fig. 1.5

    8.Open "willem" catalogue. Unpack "sterownik.zip" file. (sterownik.zip file is an automatically unpacking archive and does not require extra programme such as WINRAR or WINZIP)

    9.Enter the newly unpacked catalogue "sterownik" and start "EPROMM51.exe"programme. (See: Fig. 1.6)

    Installation of software

  • 1.Upon activating, set the following items: a.PCB3 b.LPT Printer Port on to LPT1 (0x378)

    a

    b

    2.) If the port has been found correctly, the yellow and green LED lights on the programmer will switch off.

    3.) To ensure that the programmer has been connected properly, choose from "Help" bookmark "Test Hardware" option

    Programmer test

    Programmer test55

  • 4.) If all connections are correct, the status bar will display message "Hardware present".

    Programmer test

  • Programming

    1.) To start programming individual system, you have to choose it from the list

    In case a system identical with yours cannot be found, choose another that complies most with your system

    2.)To correct the memory installation with the selected type in programme, use "Electronic ID" option

    66 Programming

  • 3.) To programme FLASH memory with a file, choose "File => Load" from upper menu or the open folder icon from the bar, and then find and indicate the file.

    lub

    4.) If all operations have been run correctly, the programme status bar will display message "Binary File Loaded OK".

    5.) From upper menu choose bookmark "Action => Program/Rest RAM".

    In case "VPP RANGE ERROR" message is displayed, change the adapter VPP configuration jumper

    6.) Once the above procedure has been completed, the window will open showing the progress in programming. The yellow and green LED light and FWH/LPC adapter LED light on the programmer will switch on.

    Programming

  • 7.) If programming has been run properly, "Device Programmed OK" message will appear, informing about the compliance of the programmed system with the selected file. FWH/LPC adapter LED light and LED lights (yellow and green) will switch off.

    Programming of the system has been completed.

    Programming

  • Erasing

    77 Erasing

    1.) .

    To erase individual system, choose items "Action => Erase 28/29/49/89/90/PIC" from the menu.

    2.) The widow will open showing a percentage progress in erasing of the system and the yellow and green LED lights and FWH/LPC adapter LED light will switch on.

    3.The system has been deleted correctly if the programme status bar displays the message "Erase completed".

    Erasing of the system has been completed.

  • Systems for programming

    EPROM: 27C64, 27C128, 27C256, 27C512, 27C010, 27C020, 27C040, 27C1001 M27C1001, M27C2001, M27C4001 27C080 (A19) ,M27C801, M87C257 2716(Vpp25V),2732, (adapter DIP24) 2764, 27128, 27256, 27512, 27010, Vpp12.5V (21Vpp Modify Circuit)

    EEPROM: 28C65,28C64, 28C128, 28C256,28C512, 28C010, 28C020, 28C040 M28C16A/17A (DIP28) (Adapter or Jumper) 28C16,XLS2816 (DIP24)

    FLASH Memory: 28F64, 28F128, 28F256, 28F512,28F010, 28F020 MX26C1000, MX26C2000, MX28F1000, MX28F2000 Am28F256A, Am28F512A, Am28F010A, Am28F020A (New command erase/prog.) -- intel --- i28F001BX, 28F004, 28F008, 28F016

    FLASH Memory: 29F64, 29F128, 29F256, 29F512,29F010, 29F020, 29F040, 29F080 29F001,29F002, 29F004, 29F008, 29F016, 29F032 Serial (I2C) EEPROM 24Cxx 24C02,24C04,24C08,24C16, 85C72, 85C82, 85C92 --- page write ---- 24C32,24C64,24C128,24C256,24C512

    Microwire EEPROM: (pin 6 ->ORG. [Schematic connect to GND]) 93C06, 93C46, 93LC46, 93C56, 93C57, 93C66, 93C76, 93C86 (8bit), AT59C11, AT59C22, AT59C13 CAT35C102, CAT35C104, CAT35C108 (pullup pin7)

    (pin 6 ->NC [No Connect]) 93C06A ,93C46X,93C56,93C66, 93C76,93C86 (NS)

    MicroChip: PIC 12C508, 12C508A, 12C509, 12C509A, 12CE518, 12CE519, 12C671, 12C672, 12CE673, 12CE674, 12F629, 12F675, 16C433, 16C54, 16C56, 16C58, 16C61, 16C62A, 16C62B, 16C63, 16C63,