Directional antennaA directional antenna or beam antenna is an antenna which radiates greater power in one or more directions allowing for increased performance on transmit and receive and reduced interference from unwanted sources. Directional antennas like Yagi-Uda antennas provide increased performance over dipole antennas when a greater concentration of radiation in a certain direction is desired.

All practical antennas are at least somewhat directional, although usually only the direction in the plane parallel to the earth is considered, and practical antennas can easily be omnidirectional in one plane.

The most common types are the Yagi-Uda antenna, the log-periodic antenna, and the corner reflector, which are frequently combined and commercially sold as residential TV antennas. Cellular repeaters often make use of external directional antennas to give a far greater signal than can be obtained on a standard cell phone. Satellite Television receivers usually use parabolic antennas.

For long and medium wavelength frequencies, tower arrays are used in most cases as directional antennas.

Antenna types

Isotropic Isotropic radiator

Omnidirectional Batwing antenna

Biconical antenna

Cage aerial

Choke ring antenna

Coaxial antenna

Crossed field antenna

Dielectric resonator antenna

Discone antenna

Folded unipole antenna

Franklin antenna

Ground-plane antenna

Halo antenna

Helical antenna

J-pole antenna

Mast radiator

Monopole antenna

Random wire antenna

Rubber ducky antenna

Turnstile antenna

T2FD antenna

T-Antenna

Umbrella antenna

Whip antenna

Directional Adcock antenna

AS-2259 Antenna

AWX antenna

Beverage antenna

Cantenna

Cassegrain antenna

Collinear antenna array

Conformal antenna

Corner reflector antenna

Curtain array

Dipole antenna

Doublet antenna

Folded inverted conformal antenna

Fractal antenna

G5RV antenna

Gizmotchy

Helical antenna

Horn antenna

Horizontal curtain

HRS antenna

Inverted vee antenna

Log-periodic antenna

Loop antenna

Microstrip antenna

Offset dish antenna

Patch antenna

Phased array

Parabolic antenna

Plasma antenna

Quad antenna

Reflective array antenna

Regenerative loop antenna

Rhombic antenna

Sector antenna

Short backfire antenna

Sloper antenna

Slot antenna

Sterba antenna

Vivaldi antenna

WokFi

Yagi-Uda antenna

Application-specific

ALLISS

Evolved antenna

Ground dipole

Reconfigurable antenna

Rectenna

Reference a Antenna Efficiency

The efficiency of an antenna relates the power delivered to the antenna and the power radiated or dissipated within the antenna. A high efficiency antenna has most of the power present at the antenna's input radiated away. A low efficiency antenna has most of the power absorbed as losses within the antenna, or reflected away due to impedance mismatch.

[Side Note: Antenna Impedance is discussed in a later section. Impedance Mismatch is simply power reflected from an antenna because it's impedance is not the correct value; hence, "impedance mismatch". ]

The losses associated within an antenna are typically the conduction losses (due to finite conductivity of the antenna) and dielectric losses (due to conduction within a dielectric which may be present within an antenna).

The antenna efficiency (or radiation efficiency) can be written as the ratio of the radiated power to the input power of the antenna:

[Equation 1]

Efficiency is ultimately a ratio, giving a number between 0 and 1. Efficiency is very often quoted in terms of a percentage; for example, an efficiency of 0.5 is the same as 50%. Antenna efficiency is also frequently quoted in decibels (dB); an efficiency of 0.1 is 10% or (-10 dB), and an efficiency of 0.5 or 50% is -3 dB.

Equation [1] is sometimes referred to as the antenna's radiation efficiency. This distinguishes it from another sometimes-used term, called an antenna's "total efficiency". The total efficiency of an antenna is the radiation efficiency multiplied by the impedance mismatch loss of the antenna, when connected to a transmission line or receiver (radio or transmitter). This can be summarized in Equation [2], where is

the antenna's total efficiency, is the antenna's loss due to impedance mismatch,

and is the antenna's radiation efficiency.

[Equation 2]

Since is always a number between 0 and 1, the total antenna efficiency is always less than the antenna's radiation efficiency. Said another way, the radiation efficiency is the same as the total antenna efficiency if there was no loss due to impedance mismatch.

Radiation PatternA radiation pattern defines the variation of the power radiated by an antenna as a function of the direction away from the antenna. This power variation as a function of the arrival angle is observed in the antenna's far field.

As an example, consider the 3-dimensional radiation pattern in Figure 1, plotted in decibels (dB) .

Figure 1. Example radiation pattern for an Antenna (generated with FEKO software).

This is an example of a donut shaped or toroidal radiation pattern. In this case, along the z-axis, which would correspond to the radiation directly overhead the antenna, there is very little power transmitted. In the x-y plane (perpendicular to the z-axis), the radiation is maximum. These plots are useful for visualizing which directions the antenna radiates.

Typically, because it is simpler, the radiation patterns are plotted in 2-d. In this case, the patterns are given as "slices" through the 3d plane. The same pattern in Figure 1 is plotted in Figure 2.

Standard spherical coordinates are used, where is the angle measured off the z-axis, and is

the angle measured counterclockwise off the x-axis.

Figure 2. Two-dimensional Radiation Patterns.

If you're unfamiliar with radiation patterns or spherical coordinates, it may take a while to see that Figure 2 represents the same radiation pattern as shown in Figure 1. The radiation pattern on the left in Figure 2 is the elevation pattern, which represents the plot of the radiation pattern as a function of the angle measured off the z-axis (for a fixed azimuth angle). Observing Figure 1, we see that the radiation pattern is minimum at 0 and 180 degrees and becomes maximum broadside to the antenna (90 degrees off the z-axis). This corresponds to the plot on the left in Figure 2.

The radiation pattern on the right in Figure 2 is the azimuthal plot. It is a function of the azimuthal angle for a fixed polar angle (90 degrees off the z-axis in this case). Since the radiation pattern in Figure 1 is symmetrical around the z-axis, this plot appears as a constant in Figure 2.

A pattern is "isotropic" if the radiation pattern is the same in all directions. Antennas with isotropic radiation patterns don't exist in practice, but are sometimes discussed as a means of comparison with real antennas.

Some antennas may also be described as "omnidirectional", which for an actual antenna means that the radiation pattern is isotropic in a single plane (as in Figure 1 above for the x-y plane, or the radiation pattern on the right in Figure 2). Examples of omnidirectional antennas include the

dipole antenna and the slot antenna.

The third category of antennas are "directional", which do not have a symmetry in the radiation pattern. These antennas typically have a single peak direction in the radiation pattern; this is the direction where the bulk of the radiated power travels. These antennas are very common; examples of antennas with highly directional radiation patterns include the dish antenna and the slotted waveguide antenna. An example of a highly directional radiation pattern (from a dish antenna) is shown in Figure 3:

Figure 3. Directional Radiation Pattern for the Dish Antenna.

In summary, the radiation pattern is a plot which allows us to visualize where the antenna transmits or receives power.

In the field of antenna design the term radiation pattern (or antenna pattern or far-field pattern) refers to the directional (angular) dependence of the strength of the radio waves from the antenna or other source.[1][2][3]

Particularly in the fields of fiber optics, lasers, and integrated optics, the term radiation pattern may also be used as a synonym for the near-field pattern or Fresnel pattern.[4] This refers to the positional dependence of the electromagnetic field in the near-field, or Fresnel region of the source. The near-field pattern is most commonly defined over a plane placed in front of the source, or over a cylindrical or spherical surface enclosing it.[1][4]

The far-field pattern of an antenna may be determined experimentally at an antenna range, or alternatively, the near-field pattern may be found using a near-field scanner, and the radiation pattern deduced from it by computation.[1] The far-field radiation pattern can also be calculated from the antenna shape by computer programs such as NEC. Other software, like HFSS can also compute the near field.

The far field radiation pattern may be represented graphically as a plot of one of a number of related variables, including; the field strength at a constant (large) radius (an amplitude pattern or field pattern), the power per unit solid angle (power pattern) and the directive gain. Very often, only the relative amplitude is plotted, normalized either to the amplitude on the antenna boresight, or to the total radiated power. The plotted quantity may be shown on a linear scale, or in dB. The plot is typically represented as a three-dimensional graph (as at right), or as separate graphs in the vertical plane and horizontal plane. This is often known as a polar diagram.

Contents

FadingIn wireless communications, fading is deviation of the attenuation affecting a signal over certain propagation media. The fading may vary with time, geographical position or radio frequency, and is often modeled as a random process. A fading channel is a communication channel comprising fading. In wireless systems, fading may either be due to multipath propagation, referred to as multipath induced fading, or due to shadowing from obstacles affecting the wave propagation, sometimes referred to as shadow fading.

Key concepts

The presence of reflectors in the environment surrounding a transmitter and receiver create multiple paths that a transmitted signal can traverse. As a result, the receiver sees the superposition of multiple copies of the transmitted signal, each traversing a different path. Each signal copy will experience differences in attenuation, delay and phase shift while travelling from the source to the receiver. This can result in either constructive or destructive interference, amplifying or attenuating the signal power seen at the receiver. Strong destructive interference is frequently referred to as a deep fade and may result in temporary failure of communication due to a severe drop in the channel signal-to-noise ratio.

A common example of deep fade is the experience of stopping at a traffic light and hearing an FM broadcast degenerate into static, while the signal is re-acquired if the vehicle moves only a fraction of a meter. The loss of the broadcast is caused by the vehicle stopping at a point where the signal experienced severe destructive interference. Cellular phones can also exhibit similar momentary fades.

Fading channel models are often used to model the effects of electromagnetic transmission of information over the air in cellular networks and broadcast communication. Fading channel

models are also used in underwater acoustic communications to model the distortion caused by the water.

Slow versus fast fading

The terms slow and fast fading refer to the rate at which the magnitude and phase change imposed by the channel on the signal changes. The coherence time is a measure of the minimum time required for the magnitude change or phase change of the channel to become uncorrelated from its previous value.

Slow fading arises when the coherence time of the channel is large relative to the delay constraint of the channel. In this regime, the amplitude and phase change imposed by the channel can be considered roughly constant over the period of use. Slow fading can be caused by events such as shadowing, where a large obstruction such as a hill or large building obscures the main signal path between the transmitter and the receiver. The received power change caused by shadowing is often modeled using a log-normal distribution with a standard deviation according to the log-distance path loss model.

Fast fading occurs when the coherence time of the channel is small relative to the delay constraint of the channel. In this regime, the amplitude and phase change imposed by the channel varies considerably over the period of use.

In a fast-fading channel, the transmitter may take advantage of the variations in the channel conditions using time diversity to help increase robustness of the communication to a temporary deep fade. Although a deep fade may temporarily erase some of the information transmitted, use of an error-correcting code coupled with successfully transmitted bits during other time instances (interleaving) can allow for the erased bits to be recovered. In a slow-fading channel, it is not possible to use time diversity because the transmitter sees only a single realization of the channel within its delay constraint. A deep fade therefore lasts the entire duration of transmission and cannot be mitigated using coding.

The coherence time of the channel is related to a quantity known as the Doppler spread of the channel. When a user (or reflectors in its environment) is moving, the user's velocity causes a shift in the frequency of the signal transmitted along each signal path. This phenomenon is known as the Doppler shift. Signals traveling along different paths can have different Doppler shifts, corresponding to different rates of change in phase. The difference in Doppler shifts between different signal components contributing to a single fading channel tap is known as the Doppler spread. Channels with a large Doppler spread have signal components that are each changing independently in phase over time. Since fading depends on whether signal components add constructively or destructively, such channels have a very short coherence time.

In general, coherence time is inversely related to Doppler spread, typically expressed as

where is the coherence time, is the Doppler spread. This equation is just an approximation,[1] to be exact, see Coherence time.

Selective fading

Selective fading or frequency selective fading is a radio propagation anomaly caused by partial cancellation of a radio signal by itself — the signal arrives at the receiver by two different paths, and at least one of the paths is changing (lengthening or shortening). This typically happens in the early evening or early morning as the various layers in the ionosphere move, separate, and combine. The two paths can both be skywave or one be groundwave.

Selective fading manifests as a slow, cyclic disturbance; the cancellation effect, or "null", is deepest at one particular frequency, which changes constantly, sweeping through the received audio.

As the carrier frequency of a signal is varied, the magnitude of the change in amplitude will vary. The coherence bandwidth measures the separation in frequency after which two signals will experience uncorrelated fading.

In flat fading, the coherence bandwidth of the channel is larger than the bandwidth of the signal. Therefore, all frequency components of the signal will experience the same magnitude of fading.

In frequency-selective fading, the coherence bandwidth of the channel is smaller than the bandwidth of the signal. Different frequency components of the signal therefore experience uncorrelated fading.

Fading is most important thing when you design any RF Design lets understand what is fading and how its effect.

The communication between the base station and mobile station in mobile systems is mostly non-LOS.

The LOS path between the transmitter and the receiver is affected by terrain and obstructed by buildings and other objects.

The mobile station is also moving in different directions at different speeds.

The RF signal from the transmitter is scattered by reflection and diffraction and reaches the receiver through many non-LOS paths.

This non-LOS path causes long-term and short term fluctuations in the form of log-normal fading and rayleigh and rician fading, which degrades the performance of the RF channel.

LONG TERM FADING

Terrain configuration & man made environment causes long-term fading. Due to various shadowing and terrain effects the signal level measured on a circle around

base station shows some random fluctuations around the mean value of received signal strength.

The long-term fades in signal strength, r, caused by the terrain configuration and man made environments form a log-normal distribution, i.e the mean received signal strength, r, varies log-normally in dB if the signal strength is measured over a distance of at least 40l.

Experimentally it has been determined that the standard deviation, s, of the mean received signal strength, r, lies between 8 to 12 dB  with the higher s generally found in large urban areas.

RAYLEIGH FADING

This phenomenon is due to multipath propagation of the signal. The Rayleigh fading is applicable to obstructed propagation paths.

All the signals are NLOS signals and there is no dominant direct path.

Signals from all paths have comparable signal strengths.

The instantaneous received power seen by a moving antenna becomes a random variable depending on the location of the antenna.

Fading is most important thing when you design any RF Design lets understand what is fading and how its effect.

The communication between the base station and mobile station in mobile systems is mostly non-LOS.

The LOS path between the transmitter and the receiver is affected by terrain and obstructed by buildings and other objects.

The mobile station is also moving in different directions at different speeds.

The RF signal from the transmitter is scattered by reflection and diffraction and reaches the receiver through many non-LOS paths.

This non-LOS path causes long-term and short term fluctuations in the form of log-normal fading and rayleigh and rician fading, which degrades the performance of the RF channel.

LONG TERM FADING

Terrain configuration & man made environment causes long-term fading. Due to various shadowing and terrain effects the signal level measured on a circle around

base station shows some random fluctuations around the mean value of received signal strength.

The long-term fades in signal strength, r, caused by the terrain configuration and man made environments form a log-normal distribution, i.e the mean received signal strength, r, varies log-normally in dB if the signal strength is measured over a distance of at least 40l.

Experimentally it has been determined that the standard deviation, s, of the mean received signal strength, r, lies between 8 to 12 dB  with the higher s generally found in large urban areas.

RAYLEIGH FADING

This phenomenon is due to multipath propagation of the signal. The Rayleigh fading is applicable to obstructed propagation paths.

All the signals are NLOS signals and there is no dominant direct path.

Signals from all paths have comparable signal strengths.

The instantaneous received power seen by a moving antenna becomes a random variable depending on the location of the antenna.

RICEAN FADING

This phenomenon is due to multipath propagation of the signal. In this case there is a partially scattered field.

One dominant signal.

Others are weaker.

 

Understanding Cellular Phone Technology

Cellular phones work much the same way as do the other wireless devices we’ve been discussing. Signals carrying voice, text, and digital data are transmitted via radio waves from one device to another. In the case of cellular networks, the data is transmitted not to a central hub in a small network of devices (as it is with Wi-Fi) or even directly from device to device (as it is with Bluetooth), but through a global network of transmitters and receivers.

Cells in a Network

What’s interesting about mobile phone networks is their cellular design. (Hence the terms “cellular network” and “cellular phone.”) By that, I mean that a mobile phone network is divided into thousands of overlapping geographic areas, or cells. A typical cellular network can be

envisioned as a mesh of hexagonal cells, as shown in Figure 4.1, each with its own base station at the center. The cells slightly overlap at the edges to ensure that users always remain within range of a base station. (You don’t want a dropped call when you’re driving between base stations.)

Figure 4.1. Cells in a cellular network.

NOTE

The cells in a cellular network vary in size, depending on how many calls are conducted within that geographic area. The smallest cells, which might cover only a few city blocks, are those where there’s the heaviest population density, and thus the largest demand for service. The largest cells are most often in rural areas with a smaller population per square mile.

The base station at the center of each group of cells functions as the hub for those cells—not of the entire network, but of that individual piece of the network. RF signals are transmitted by an individual phone and received by the base station, where they are then re-transmitted from the base station to another mobile phone. Transmitting and receiving are done over two slightly different frequencies.

Base stations are connected to one another via central switching centers which track calls and transfer them from one base station to another as callers move between cells; the handoff is (ideally) seamless and unnoticeable. Each base station is also connected to the main telephone network, and can thus relay mobile calls to landline phones.

Carrying a Two-Way Radio

All this transmission within a cellular network originates with the handheld cell phone. A mobile phone is actually a two-way radio, containing both a low-power transmitter (to transmit data) and a receiver (to receive data).

When I say low power, I mean low power—really low power. The typical cell phone includes a dual-strength transmitter, capable of transmitting either 0.6-watt or 3-watt signals. In comparison, a larger AM radio station will typically broadcast a 50,000-watt signal; even smaller AM stations broadcast 5,000-watt signals. A cell phone’s 3-watt signal is puny in comparison.

The reason mobile phones can get by with such low-power transmitters is that they’re transmitting within a relatively limited range—within the current network cell. It’s not necessary or desirable for a phone’s signal to extend beyond the current cell; this way, the same broadcast frequencies can be used by multiple cells without danger of interference.

How do cell phones work?You've seen them, perhaps you've used one. Each day something like 100,000 people around the world sign up for and start using a cellular phone. Therefore it is likely that you or someone you know has a cell phone and uses it on a regular basis. They are such great gadgets - with a cell phone you can talk to anyone on the planet from just about anywhere (80% of the U.S. has coverage).

But have you ever wondered how a cell phone works? Or what happens when you talk on one? Or how a call gets routed to a regular phone? we will discuss the technology behind cell phones so that you can see how amazing they really are.

One of the most interesting things about a cell phone is that it is really a radio - an extremely sophisticated radio, but a radio nonetheless. A good way to understand the sophistication of a cell phone is to compare it to a CB radio or a walkie-talkie. A CB radio is a simplex device. That is, two people communicating on a CB radio use the same frequency, so only one person can talk at a time. A cell phone is a duplex device, so it uses one frequency for talking and a second, separate frequency for listening. A CB radio has 40 channels. A cell phone can communicate on 1,664 channels. Cell phones also operate within cells and they can switch cells as they move around. Cells give cell phones incredible range. A walkie-talkie can transmit perhaps a mile. A CB radio, because it has much higher power, can transmit perhaps 5 miles. Someone using a cell phone, on the other hand, can drive clear across a city and maintain a conversation the entire time. Cells are what give a cell phone its incredible range.

The MAC level (link layer)This section of the document focus on the next layer up, the link layer. This mostly comprise the MAC (Medium Access Control) protocol. Different MAC protocols and techniques are presented.

5.1 Main channel access mechanismsThe main job of the MAC protocol is to regulate the usage of the medium, and this is done through a channel access mechanism. A channel access mechanism is a way to divide the main resource between nodes, the radio channel, by regulating the use of it. It tells each node when it can transmit and when it is expected to receive data. The channel access mechanism is the core of the MAC protocol. In this

section, we describe TDMA, CSMA and polling which are the 3 main classes of channel access mechanisms for radio.

5.1.1 TDMAIn this chapter, we discuss TDMA as a channel access mechanism and not its applications and protocols based on it.

TDMA (Time Division Multiplex Access) is very simple. A specific node, the base station, has the responsibility to coordinate the nodes of the network. The time on the channel is divided into time slots, which are generally of fixed size. Each node of the network is allocated a certain number of slots where it can transmit. Slots are usually organised in a frame, which is repeated on a regular basis.

The base station specify in the beacon (a management frame) the organisation of the frame. Each node just needs to follow blindly the instruction of the base station. Very often, the frame is organised as downlink (base station to node) and uplink (node to base station) slots, and all the communications goes through the base station. A service slot allows a node to request the allocation of a connection, by sending a connection request message in it (see chapter   5.2.4 ). In some standards, uplink and downlink frames are one different frequencies, and the service slots might also be a separate channel.

TDMA channel access mechanism :

TDMA suits very well phone applications, because those application have very predictable needs (fixed and identical bit rate). Each handset is allocated a downlink and a uplink slot of a fixed size (the size of the voice data for the duration of the frame). This is no surprise why TDMA is used into all cellular phone standards (GSM in Europe, TDMA and PCS in the USA) and cordless phone standards (DECT in Europe). TDMA is also very good to achieve low latency and guarantee of bandwidth (where CSMA/CA is quite bad).

TDMA is not well suited for data networking applications, because it is very strict and inflexible. IP is connectionless and generates bursty traffic which is very unpredictable by nature, while TDMA is connection oriented (so it has to suffer the overhead of creating connections for single

IP packets). TDMA use fixed size packets and usually symmetrical link, which doesn't suit IP that well (variable size packets).

TDMA is very much dependant of the quality of the frequency band. In a dedicated clean band, as it is the case for cellular phone standard, TDMA is fine. But, because of it's inflexibility, and because it doesn't really take care of what's happening on the channel, TDMA can't cope and adapt to the bursty interference sources found in the unlicensed bands (unless a retry mechanism is put on top of it).

5.1.2 CSMA/CACSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) is the channel access mechanism used by most wireless LANs in the ISM bands. A channel access mechanism is the part of the protocol which specifies how the node uses the medium : when to listen, when to transmit...

The basic principles of CSMA/CA are listen before talk and contention. This is an asynchronous message passing mechanism (connectionless), delivering a best effort service, but no bandwidth and latency guarantee (you are still following ?). It's main advantages are that it is suited for network protocols such as TCP/IP, adapts quite well with the variable condition of traffic and is quite robust against interferences.

CSMA/CA is fundamentally different from the channel access mechanism used by cellular phone systems (see TDMA in chapter   5.1.1 ).

CSMA/CA is derived from CSMA/CD (Collision Detection), which is the base of Ethernet. The main difference is the collision avoidance : on a wire, the transceiver has the ability to listen while transmitting and so to detect collisions (with a wire all transmissions have approximately the same strength). But, even if a radio node could listen on the channel while transmitting, the strength of its own transmissions would mask all other signals on the air. So, the protocol can't directly detect collisions like with Ethernet and only tries to avoid them.

CSMA/CA channel Access Mechanisms :

The protocol starts by listening on the channel (this is called carrier sense), and if it is found to be idle, it sends the first packet in the transmit queue. If it is busy (either another node transmission or interference), the node waits the end of the current transmission and then starts the contention (wait a random amount of time). When its contention timer expires, if the channel is still idle, the node sends the packet. The node having chosen the shortest contention delay wins and transmits its packet. The other nodes just wait for the next contention (at the end of this packet). Because the contention is a random number and done for every packets, each node is given an equal chance to access the channel (on average - it is statistic).

As we have mentioned, we can't detect collisions on the radio, and because the radio needs time to switch from receive to transmit, this contention is usually slotted (a transmission may start only at the beginning of a slot : 50 µs in 802.11 FH and 20 µs in 802.11 DS). This makes the average contention delay larger, but reduces significantly the collisions (we can't totally avoid them).

5.1.3 Polling MACPolling is the third major channel access mechanism, after TDMA and CSMA/CA (see chapter 5.1.1 and chapter 5.1.2 respectively - There exist also Token Ring, but I guess that nobody would be crazy enough to implement it on a radio link). The most successful networking standard using polling is 100vg (IEEE 802.12), but some wireless standard are also using it. For example, 802.11 offers a polling channel access mechanism (Point Coordination Function) in addition to the CSMA/CA one.

Polling is in fact in between TDMA and CSMA/CA. The base station retains total control over the channel, but the frame content is no more fixed, allowing variable size packets to be sent. The base station sends a specific packet (a poll packet) to trigger the transmission by the node. The node just wait to receive a poll packet, and upon reception sends what it has to transmit.

Polling can be implemented as a connection oriented service (very much like TDMA, but with higher flexibility in packet size) or connection less-service (asynchronous packet based). The base station can either poll permanently all the nodes of the network just to check if they have something to send (that is workable only with a very limited number of nodes), or the protocol use reservation slots (see chapter   5.2.4 ) where each node can request a connection or to transmit a packet (depending is the MAC protocol is connection oriented or not).

Polling channel Access Mechanisms :

In the case of 100vg, the polling mechanism doesn't use any bandwidth (it's done out of band through tones), leading to a very efficient use of the channel (over 96 % user throughput). For 802.11 and wireless LAN, all the polling packets have to be transmitted over the air, generating much more overhead. More recent system use reservation slots, which is more flexible but still require significant overhead.

As CSMA/CA offers ad-hoc networking (no need of a base station) and similar performance, it is usually preferred in most wireless LANs. For example, most 802.11 vendors prefer to use the distributed mode (CSMA/CA) over the coordinated mode (polling).

5.1.4 Reservation protocols and WATMThe most interesting feature of protocols based on TDMA or Polling mechanism is that the Base Station has absolute control of the traffic and can guarantee bandwidth and latency for applications that require it. Sceptics might wonder what can be guaranteed anyway in an environment open to interferers and without deployment control (see chapter 4.1 ), but that's another topic of discussions.

The guarantee of bandwidth is essential for people deploying Wireless Distributions Systems (also called Last Mile Delivery Systems), like replacing the cable between your house and your ISP with wireless. Those people want to be able to restrict and segregate users and guarantee fairness. Standards such as HiperLan II (Broadband Radio Access Network project - see chapter   6.4 ) is aiming at those usages.

The basic idea is to put ATM (Asynchronous Transfer Mode) over radio, as ATM implement all the Quality Of Service features that they are dreaming off. The network is centrally managed (so uses TDMA or Polling mechanism with reservation slots), the base station implement a call admission control (accept or reject new ATM circuits) and scheduler (prioritise and send ATM cells) to guarantee the quality of service requested. On top of the MAC, all the usual ATM layers are needed (virtual circuits, segmentation/reassembly, IP adaptation...), as well as some specific mobile features (to manage roaming).

Unfortunately, radio transmission has a lot of overhead (like large synchronisation field and headers) which is somewhat incompatible with the small ATM cells. The main benefit of ATM small cells is to allow very efficient switching, but this is not needed over radio. At the end of the

day, WATM doesn't resemble at all to ATM ; ATM uses individual channel for each node and is asynchronous, whereas WATM uses a shared medium and is totally synchronous.

5.2 MAC techniquesWe have described the main principle of CSMA/CA (see chapter 5.1.2 ), but most MAC protocols use additional techniques to improve the performance of CSMA/CA.

5.2.1 MAC retransmissionsAs we have seen in the previous chapter, the main problem of the CSMA/CA protocol is that the transmitter can't detect collisions on the medium. There is also a higher error rate on the air than on a wire (see chapter 4.8 ), so a higher chance of packets being corrupted. TCP doesn't like very much packet losses at the MAC layer (see TCP and packet losses problem - chapter 5.4.5 ). Because of that, most MAC protocols also implement positive acknowledgement and MAC level retransmissions to avoid losing packets on the air.

The principle is quite simple : each time a node receives a packet, it sends back immediately a short message (an ack) to the transmitter to indicate that it has successfully received the packet without errors. If after sending a packet the transmitter doesn't receive an ack, it knows that the packet was lost, so it will retransmit the packet (after contending again for the medium, like in Ethernet).

Most MAC protocols use a stop and go mechanism, they transmit the next packet of the queue only if the current packet has been properly acknowledged (no sliding window mechanism like in TCP). The rationale is that it makes the protocol simpler, minimise latency and avoid desenquencing packets (something that TCP doesn't like as well).

MAC retransmissions in CSMA/CA :

The acks are "embedded" in the MAC protocol, so they are guaranteed not to collide (the contention starts after the ack - see figure). These acks are very different from the TCP acks, which work at a different level (and on a different time frame). Of course, broadcast and multicast packets are not acknowledged, so they are more likely to fail...

If all modern Wireless LAN protocols implement this essential feature, some old products may lack it. Wireless WAN protocols (like satellite links) don't implement that either, because the round trip delay in their case is so long that by the time they would receive the ack they could have sent another packet. If your Wireless LAN doesn't implement MAC level retransmissions, all is not lost : students of Berkeley have created a protocol called snoop (see at ftp://daedalus.cs.berkeley.edu/pub/snoop/) which filters the TCP acks and retransmits the lost packets before TCP even notices that they are lost (this is still a link level retransmission, but done just over the MAC).

5.2.2 FragmentationThe radio medium has a higher error rate than a wire. We have explained in the previous chapter that it was why most products were including MAC level retransmissions to avoid losing packets.

MAC level retransmissions solve this problem, but is not really performant. If the packet to transmit is long and contains only one error, the node needs to retransmit it entirely. If the error rate is significantly high, we could come to some situation were the probability of error in large packet is dangerously close to 1 (we can't fit a packet between the bursts of errors due to fading or interferers), so we can't get packet through.

This is why some products use fragmentation. Fragmentation is sending the big packets in small pieces over the medium. Of course, this adds some overhead, because it duplicates packet headers in every fragments. Each fragment is individually checked and retransmitted if necessary. The first advantage is that in case of error, the node needs only to retransmit one small fragment, so it is faster. The second advantage is that if the medium is very noisy, a small packet has a higher probability to get through without errors, so the node increases its chance of success in bad conditions.

5.2.3 RTS/CTSIn the chapter about range (chapter 4.6 ), we have seen that the main effect of transmission on radio waves is the attenuation of the signal. Because of this attenuation, we have very commonly a problem of hidden nodes.

The hidden node problem comes from the fact that all nodes may not hear each other because the attenuation is too strong between them. Because transmissions are based on the carrier sense mechanism, those nodes ignore each other and may transmit at the same time. Usually, this is a good thing because it allows frequency reuse (they are effectively in different cells).

But, for a node placed in between, these simultaneous transmissions have a comparable strength and so collide (in its receiver). This node could be impossible to reach because of these collisions.

The fundamental problem with carrier sense o

Fundamentals of Communications Access Technologies: FDMA, TDMA, CDMA, OFDMA, AND SDMAccess methods are multiplexing techniques that provide communications services to multiple users in a single-bandwidth wired or wireless medium. Communications channels, whether they’re wireless spectrum segments or cable connections, are expensive. Communications services providers must engage multiple paid users over limited resources to make a profit. Access methods allow many users to share these limited channels to provide the economy of scale necessary for a successful communications business. There are five basic access or multiplexing methods: frequency division multiple access (FDMA), time division multiple access (TDMA), code division multiple access (CDMA), orthogonal frequency division multiple access (OFDMA), and spatial division multiple access (SDMA).

FDMA

FDMA is the process of dividing one channel or bandwidth into multiple individual bands, each for use by a single user (Fig. 1). Each individual band or channel is wide enough to accommodate the signal spectra of the transmissions to be propagated. The data to be transmitted is modulated on to each subcarrier, and all of them are linearly mixed together.

 

1. FDMA divides the shared medium bandwidth into individual channels. Subcarriers modulated by the information to be transmitted occupy each subchannel.

The best example of this is the cable television system. The medium is a single coax cable that is used to broadcast hundreds of channels of video/audio programming to homes. The coax cable has a useful bandwidth from about 4 MHz to 1 GHz. This bandwidth is divided up into 6-MHz wide channels. Initially, one TV station or channel used a single 6-MHz band. But with digital techniques, multiple TV channels may share a single band today thanks to compression and multiplexing techniques used in each channel.

This technique is also used in fiber optic communications systems. A single fiber optic cable has enormous bandwidth that can be subdivided to provide FDMA. Different data or information sources are each assigned a different light frequency for transmission. Light generally isn’t referred to by frequency but by its wavelength (λ). As a result, fiber optic FDMA is called wavelength division multiple access (WDMA) or just wavelength division multiplexing (WDM).

One of the older FDMA systems is the original analog telephone system, which used a hierarchy of frequency multiplex techniques to put multiple telephone calls on single line. The analog 300-Hz to 3400-Hz voice signals were used to modulate subcarriers in 12 channels from 60 kHz to 108 kHz. Modulator/mixers created single sideband (SSB) signals, both upper and lower sidebands. These subcarriers were then further frequency multiplexed on subcarriers in the 312-kHz to 552-kHz range using the same modulation methods. At the receiving end of the system, the signals were sorted out and recovered with filters and demodulators.

Original aerospace telemetry systems used an FDMA system to accommodate multiple sensor data on a single radio channel. Early satellite systems shared individual 36-MHz bandwidth transponders in the 4-GHz to 6-GHz range with multiple voice, video, or data signals via FDMA. Today, all of these applications use TDMA digital techniques.

TDMA

TDMA is a digital technique that divides a single channel or band into time slots. Each time slot is used to transmit one byte or another digital segment of each signal in sequential serial data format. This technique works well with slow voice data signals, but it’s also useful for compressed video and other high-speed data.

A good example is the widely used T1 transmission system, which has been used for years in the telecom industry. T1 lines carry up to 24 individual voice telephone calls on a single line (Fig. 2). Each voice signal usually covers 300 Hz to 3000 Hz and is digitized at an 8-kHz rate, which is just a bit more than the minimal Nyquist rate of two times the highest-frequency component needed to retain all the analog content.

 

2. This T1 digital telephony frame illustrates TDM and TDMA. Each time slot is allocated to one user. The high data rate makes the user unaware of the lack of simultaneity.

The digitized voice appears as individual serial bytes that occur at a 64-kHz rate, and 24 of these bytes are interleaved, producing one T1 frame of data. The frame occurs at a 1.536-MHz rate (24 by 64 kHz) for a total of 192 bits. A single synchronizing bit is added for timing purposes for an overall data rate of 1.544 Mbits/s. At the receiving end, the individual voice bytes are recovered at the 64-kHz rate and passed through a digital-to-analog converter (DAC) that reproduces the analog voice.

The basic GSM (Global System of Mobile Communications) cellular phone system is TDMA-based. It divides up the radio spectrum into 200-kHz bands and then uses time division techniques to put eight voice calls into one channel. Figure 3 shows one frame of a GSM TDMA signal. The eight time slots can be voice signals or data such as texts or e-mails. The frame is transmitted at a 270-kbit/s rate using Gaussian minimum shift keying (GMSK), which is a form of frequency shift keying (FSK) modulation.

 

3. This GSM digital cellular method shows how up to eight users can share a 200-kHz channel in different time slots within a frame of 1248 bits.

CDMA

CDMA is another pure digital technique. It is also known as spread spectrum because it takes the digitized version of an analog signal and spreads it out over a wider bandwidth at a lower power level. This method is called direct sequence spread spectrum (DSSS) as well (Fig. 4). The digitized and compressed voice signal in serial data form is spread by processing it in an XOR circuit along with a chipping signal at a much higher frequency. In the cdma IS-95 standard, a 1.2288-Mbit/s chipping signal spreads the digitized compressed voice at 13 kbits/s.

 

4. Spread spectrum is the technique of CDMA. The compressed and digitized voice signal is processed in an XOR logic circuit along with a higher-frequency coded chipping signal. The result is that the digital voice is spread over a much wider bandwidth that can be shared with other users using different codes.

The chipping signal is derived from a pseudorandom code generator that assigns a unique code to each user of the channel. This code spreads the voice signal over a bandwidth of 1.25 MHz. The resulting signal is at a low power level and appears more like noise. Many such signals can occupy the same channel simultaneously. For example, using 64 unique chipping codes allows up to 64 users to occupy the same 1.25-MHz channel at the same time. At the receiver, a correlating circuit finds and identifies a specific caller’s code and recovers it.

The third generation (3G) cell-phone technology called wideband CDMA (WCDMA) uses a similar method with compressed voice and 3.84-Mbit/s chipping codes in a 5-MHz channel to allow multiple users to share the same band.

OFDMA

OFDMA is the access technique used in Long-Term Evolution (LTE) cellular systems to accommodate multiple users in a given bandwidth. Orthogonal frequency division multiplexing (OFDM) is a modulation method that divides a channel into multiple narrow orthogonal bands that are spaced so they don’t interfere with one another. Each band is divided into hundreds or even thousands of 15-kHz wide subcarriers.

The data to be transmitted is divided into many lower-speed bit streams and modulated onto the subcarriers. Time slots within each subchannel data stream are used to package the data to be transmitted (Fig. 5). This technique is very spectrally efficient, so it provides very high data rates. It also is less affected by multipath propagation effects.

 

5. OFDMA assigns a group of subcarriers to each user. The subcarriers are part of the large number of subcarriers used to implement OFDM for LTE. The data may be voice, video, or something else, and it’s assembled into time segments that are then transmitted over some of the assigned subcarriers.

To implement OFDMA, each user is assigned a group of subchannels and related time slots. The smallest group of subchannels assigned is 12 and called a resource block (RB). The system assigns the number of RBs to each user as needed.

SDMA

SDMA uses physical separation methods that permit the sharing of wireless channels. For instance, a single channel may be used simultaneously if the users are spaced far enough from one another to avoid interference. Known as frequency reuse, the method is widely used in cellular radio systems. Cell sites are spaced from one another to minimize interference.

In addition to spacing, directional antennas are used to avoid interference. Most cell sites use three antennas to create 120° sectors that allow frequency sharing (Fig. 6a). New technologies

like smart antennas or adaptive arrays use dynamic beamforming to shrink signals into narrow beams that can be focused on specific users, excluding all others (Fig. 6b).

6. SDMA separates users on shared frequencies by isolating them with directional antennas. Most cell sites have three antenna arrays to separate their coverage into isolated 120° sectors (a). Adaptive arrays use beamforming to pinpoint desired users while ignoring any others on the same frequency (b).

One unique variation of SDMA, polarization division multiple access (PDMA), separates signals by using different polarizations of the antennas. Two different signals then can use the same frequency, one transmitting a vertically polarized signal and the other transmitting a horizontally polarized signal.

The signals won’t interfere with one another even if they’re on the same frequency because they’re orthogonal and the antennas won’t respond to the oppositely polarized signal. Separate vertical and horizontal receiver antennas are used to recover the two orthogonal signals. This technique is widely used in satellite systems.

Polarization is also used for multiplexing in fiber optic systems. The new 100-Gbit/s systems use dual polarization quadrature phase shift keying (DP-QPSK) to achieve high speeds on a single fiber. The high-speed data is divided into two slower data streams, one using vertical light polarization and the other horizontal light polarization. Polarization filters separate the two signals at the transmitter and receiver and merge them back into the high-speed stream.

Other Methods

A unique and widely used method of multiple access is carrier sense multiple access with collision detection (CSMA-CD). This is the classical access method used in Ethernet local-area networks (LANs). It allows multiple users of the network to access the single cable for transmission. All network nodes listen continuously. When they want to send data, they listen first and then transmit if no other signals are on the line. For instance, the transmission will be one packet or frame. Then the process repeats. If two or more transmissions occur simultaneously, a collision occurs. The network interface circuitry can detect a collision, and then the nodes will wait a random time before retransmitting.

A variation of this method is called carrier sense multiple access with collision avoidance (CSMA-CA). This method is similar to CSMA-CD. However, a special scheduling algorithm is used to determine the appropriate time to transmit over the shared channel. While the CSMA-CD technique is most used in wired networks, CSMA-CA is the preferred method in wireless networks.

Cellular networkA cellular network or mobile network is a wireless network distributed over land areas called cells, each served by at least one fixed-location transceiver, known as a cell site or base station. In a cellular network, each cell uses a different set of frequencies from neighboring cells, to avoid interference and provide guaranteed bandwidth within each cell.

When joined together these cells provide radio coverage over a wide geographic area. This enables a large number of portable transceivers (e.g., mobile phones, pagers, etc.) to communicate with each other and with fixed transceivers and telephones anywhere in the network, via base stations, even if some of the transceivers are moving through more than one cell during transmission.

Cellular networks offer a number of desirable features:

More capacity than a single large transmitter, since the same frequency can be used for multiple links as long as they are in different cells

Mobile devices use less power than with a single transmitter or satellite since the cell towers are closer

Larger coverage area than a single terrestrial transmitter, since additional cell towers can be added indefinitely and are not limited by the horizon

Major telecommunications providers have deployed voice and data cellular networks over most of the inhabited land area of the Earth. This allows mobile phones and mobile computing devices to be connected to the public switched telephone network and public Internet. Private cellular networks can be used for research[1] or for large organizations and fleets, such as dispatch for local public safety agencies or a taxicab company.[2]

Concept

Example of frequency reuse factor or pattern 1/4

In a cellular radio system, a land area to be supplied with radio service is divided into regular shaped cells, which can be hexagonal, square, circular or some other regular shapes, although hexagonal cells are conventional. Each of these cells is assigned multiple frequencies (f1 – f6) which have corresponding radio base stations. The group of frequencies can be reused in other cells, provided that the same frequencies are not reused in adjacent neighboring cells as that would cause co-channel interference.

The increased capacity in a cellular network, compared with a network with a single transmitter, comes from the mobile communication switching system developed by Amos Joel of Bell Labs [3] that permitted multiple callers in the same area to use the same frequency by switching calls made using the same frequency to the nearest available cellular tower having that frequency available and from the fact that the same radio frequency can be reused in a different area for a completely different transmission. If there is a single plain transmitter, only one transmission can be used on any given frequency. Unfortunately, there is inevitably some level of interference from the signal from the other cells which use the same frequency. This means that, in a standard FDMA system, there must be at least a one cell gap between cells which reuse the same frequency.

In the simple case of the taxi company, each radio had a manually operated channel selector knob to tune to different frequencies. As the drivers moved around, they would change from channel to channel. The drivers knew which frequency covered approximately what area. When they did not receive a signal from the transmitter, they would try other channels until they found

one that worked. The taxi drivers would only speak one at a time, when invited by the base station operator (this is, in a sense, time division multiple access (TDMA)).

Cell signal encoding

To distinguish signals from several different transmitters, frequency division multiple access (FDMA) and code division multiple access (CDMA) were developed.

With FDMA, the transmitting and receiving frequencies used in each cell are different from the frequencies used in each neighbouring cell. In a simple taxi system, the taxi driver manually tuned to a frequency of a chosen cell to obtain a strong signal and to avoid interference from signals from other cells.

The principle of CDMA is more complex, but achieves the same result; the distributed transceivers can select one cell and listen to it.

Other available methods of multiplexing such as polarization division multiple access (PDMA) and time division multiple access (TDMA) cannot be used to separate signals from one cell to the next since the effects of both vary with position and this would make signal separation practically impossible. Time division multiple access, however, is used in combination with either FDMA or CDMA in a number of systems to give multiple channels within the coverage area of a single cell.

Frequency reuse

The key characteristic of a cellular network is the ability to re-use frequencies to increase both coverage and capacity. As described above, adjacent cells must use different frequencies, however there is no problem with two cells sufficiently far apart operating on the same frequency. The elements that determine frequency reuse are the reuse distance and the reuse factor.

The reuse distance, D is calculated as

where R is the cell radius and N is the number of cells per cluster. Cells may vary in radius from 1 to 30 kilometres (0.62 to 18.64 mi). The boundaries of the cells can also overlap between adjacent cells and large cells can be divided into smaller cells.[4]

The frequency reuse factor is the rate at which the same frequency can be used in the network. It is 1/K (or K according to some books) where K is the number of cells which cannot use the same frequencies for transmission. Common values for the frequency reuse factor are 1/3, 1/4, 1/7, 1/9 and 1/12 (or 3, 4, 7, 9 and 12 depending on notation).[5]

In case of N sector antennas on the same base station site, each with different direction, the base station site can serve N different sectors. N is typically 3. A reuse pattern of N/K denotes a

further division in frequency among N sector antennas per site. Some current and historical reuse patterns are 3/7 (North American AMPS), 6/4 (Motorola NAMPS), and 3/4 (GSM).

If the total available bandwidth is B, each cell can only use a number of frequency channels corresponding to a bandwidth of B/K, and each sector can use a bandwidth of B/NK.

Code division multiple access-based systems use a wider frequency band to achieve the same rate of transmission as FDMA, but this is compensated for by the ability to use a frequency reuse factor of 1, for example using a reuse pattern of 1/1. In other words, adjacent base station sites use the same frequencies, and the different base stations and users are separated by codes rather than frequencies. While N is shown as 1 in this example, that does not mean the CDMA cell has only one sector, but rather that the entire cell bandwidth is also available to each sector individually.

Depending on the size of the city, a taxi system may not have any frequency-reuse in its own city, but certainly in other nearby cities, the same frequency can be used. In a large city, on the other hand, frequency-reuse could certainly be in use.

Recently also orthogonal frequency-division multiple access based systems such as LTE are being deployed with a frequency reuse of 1. Since such systems do not spread the signal across the frequency band, inter-cell radio resource management is important to coordinate resource allocation between different cell sites and to limit the inter-cell interference. There are various means of Inter-Cell Interference Coordination (ICIC) already defined in the standard.[6] Coordinated scheduling, multi-site MIMO or multi-site beam forming are other examples for inter-cell radio resource management that might be standardized in the future.

Directional antennas

Cellular telephone frequency reuse pattern. See U.S. Patent 4,144,411

Cell towers frequently use a directional signal to improve reception in higher traffic areas. In the United States, the FCC limits omni-directional cell tower signals to 100 watts of power. If the tower has directional antennas, the FCC allows the cell operator to broadcast up to 500 watts of effective radiated power (ERP).[7]

Cell phone companies use this directional signal to improve reception along highways and inside buildings like stadiums and arenas.[7] As a result, a cell phone user may be standing in sight of a cell tower, but still have trouble getting a good signal because the directional antennas point a different direction.[7]

Although the original cell towers created an even, omni-directional signal, were at the centers of the cells and were omni-directional, a cellular map can be redrawn with the cellular telephone towers located at the corners of the hexagons where three cells converge.[8] Each tower has three sets of directional antennas aimed in three different directions with 120 degrees for each cell (totaling 360 degrees) and receiving/transmitting into three different cells at different

frequencies. This provides a minimum of three channels, and three towers for each cell and greatly increases the chances of receiving a usable signal from at least one direction.

The numbers in the illustration are channel numbers, which repeat every 3 cells. Large cells can be subdivided into smaller cells for high volume areas.[9]

Broadcast messages and paging

Practically every cellular system has some kind of broadcast mechanism. This can be used directly for distributing information to multiple mobiles, commonly, for example in mobile telephony systems, the most important use of broadcast information is to set up channels for one to one communication between the mobile transceiver and the base station. This is called paging. The three different paging procedures generally adopted are sequential, parallel and selective paging.

The details of the process of paging vary somewhat from network to network, but normally we know a limited number of cells where the phone is located (this group of cells is called a Location Area in the GSM or UMTS system, or Routing Area if a data packet session is involved; in LTE, cells are grouped into Tracking Areas). Paging takes place by sending the broadcast message to all of those cells. Paging messages can be used for information transfer. This happens in pagers, in CDMA systems for sending SMS messages, and in the UMTS system where it allows for low downlink latency in packet-based connections.

Movement from cell to cell and handover

In a primitive taxi system, when the taxi moved away from a first tower and closer to a second tower, the taxi driver manually switched from one frequency to another as needed. If a communication was interrupted due to a loss of a signal, the taxi driver asked the base station operator to repeat the message on a different frequency.

In a cellular system, as the distributed mobile transceivers move from cell to cell during an ongoing continuous communication, switching from one cell frequency to a different cell frequency is done electronically without interruption and without a base station operator or manual switching. This is called the handover or handoff. Typically, a new channel is automatically selected for the mobile unit on the new base station which will serve it. The mobile unit then automatically switches from the current channel to the new channel and communication continues.

The exact details of the mobile system's move from one base station to the other varies considerably from system to system (see the example below for how a mobile phone network manages handover).

Mobile phone network

GSM network architecture

The most common example of a cellular network is a mobile phone (cell phone) network. A mobile phone is a portable telephone which receives or makes calls through a cell site (base station), or transmitting tower. Radio waves are used to transfer signals to and from the cell phone.

Modern mobile phone networks use cells because radio frequencies are a limited, shared resource. Cell-sites and handsets change frequency under computer control and use low power transmitters so that the usually limited number of radio frequencies can be simultaneously used by many callers with less interference.

A cellular network is used by the mobile phone operator to achieve both coverage and capacity for their subscribers. Large geographic areas are split into smaller cells to avoid line-of-sight signal loss and to support a large number of active phones in that area. All of the cell sites are connected to telephone exchanges (or switches), which in turn connect to the public telephone network.

In cities, each cell site may have a range of up to approximately 1⁄2 mile (0.80 km), while in rural areas, the range could be as much as 5 miles (8.0 km). It is possible that in clear open areas, a user may receive signals from a cell site 25 miles (40 km) away.

Since almost all mobile phones use cellular technology, including GSM, CDMA, and AMPS (analog), the term "cell phone" is in some regions, notably the US, used interchangeably with "mobile phone". However, satellite phones are mobile phones that do not communicate directly with a ground-based cellular tower, but may do so indirectly by way of a satellite.

There are a number of different digital cellular technologies, including: Global System for Mobile Communications (GSM), General Packet Radio Service (GPRS), cdmaOne, CDMA2000, Evolution-Data Optimized (EV-DO), Enhanced Data Rates for GSM Evolution (EDGE), Universal Mobile Telecommunications System (UMTS), Digital Enhanced Cordless

Telecommunications (DECT), Digital AMPS (IS-136/TDMA), and Integrated Digital Enhanced Network (iDEN).

Structure of the mobile phone cellular network

A simple view of the cellular mobile-radio network consists of the following:

A network of radio base stations forming the base station subsystem. The core circuit switched network for handling voice calls and text

A packet switched network for handling mobile data

The public switched telephone network to connect subscribers to the wider telephony network

This network is the foundation of the GSM system network. There are many functions that are performed by this network in order to make sure customers get the desired service including mobility management, registration, call set up, and handover.

Any phone connects to the network via an RBS (Radio Base Station) at a corner of the corresponding cell which in turn connects to the Mobile switching center (MSC). The MSC provides a connection to the public switched telephone network (PSTN). The link from a phone to the RBS is called an uplink while the other way is termed downlink.

Radio channels effectively use the transmission medium through the use of the following multiplexing and access schemes: frequency division multiple access (FDMA), time division multiple access (TDMA), code division multiple access (CDMA), and space division multiple access (SDMA).

Cellular handover in mobile phone networksMain article: Handover

As the phone user moves from one cell area to another cell while a call is in progress, the mobile station will search for a new channel to attach to in order not to drop the call. Once a new channel is found, the network will command the mobile unit to switch to the new channel and at the same time switch the call onto the new channel.

With CDMA, multiple CDMA handsets share a specific radio channel. The signals are separated by using a pseudonoise code (PN code) specific to each phone. As the user moves from one cell to another, the handset sets up radio links with multiple cell sites (or sectors of the same site) simultaneously. This is known as "soft handoff" because, unlike with traditional cellular technology, there is no one defined point where the phone switches to the new cell.

In IS-95 inter-frequency handovers and older analog systems such as NMT it will typically be impossible to test the target channel directly while communicating. In this case other techniques have to be used such as pilot beacons in IS-95. This means that there is almost always a brief break in the communication while searching for the new channel followed by the risk of an unexpected return to the old channel.

HandoverIn cellular telecommunications, the term handover or handoff refers to the process of transferring an ongoing call or data session from one channel connected to the core network to another channel. In satellite communications it is the process of transferring satellite control responsibility from one earth station to another without loss or interruption of service.

Handover or handoff

American English use the term handoff, and this is most commonly used within some American organizations such as 3GPP2 and in American originated technologies such as CDMA2000. In British English the term handover is more common, and is used within international and European organisations such as ITU-T, IETF, ETSI and 3GPP, and standardised within European originated standards such as GSM and UMTS. The term handover is more common than handoff in academic research publications and literature, while handoff is slightly more common within the IEEE and ANSI organisations.[original research?]

Purpose

In telecommunications there may be different reasons why a handover might be conducted:

when the phone is moving away from the area covered by one cell and entering the area covered by another cell the call is transferred to the second cell in order to avoid call termination when the phone gets outside the range of the first cell;

when the capacity for connecting new calls of a given cell is used up and an existing or new call from a phone, which is located in an area overlapped by another cell, is transferred to that cell in order to free-up some capacity in the first cell for other users, who can only be connected to that cell;

in non-CDMA networks when the channel used by the phone becomes interfered by another phone using the same channel in a different cell, the call is transferred to a different channel in the same cell or to a different channel in another cell in order to avoid the interference;

again in non-CDMA networks when the user behaviour changes, e.g. when a fast-travelling user, connected to a large, umbrella-type of cell, stops then the call may be transferred to a smaller macro cell or even to a micro cell in order to free capacity on the umbrella cell for other fast-traveling users and to reduce the potential interference to other cells or users (this works in reverse too, when a user is detected to be moving faster than a certain threshold, the call can be transferred to a larger umbrella-type of cell in order to minimize the frequency of the handovers due to this movement);

in CDMA networks a handover (see further down) may be induced in order to reduce the interference to a smaller neighboring cell due to the "near-far" effect even when the phone still has an excellent connection to its current cell;

etc.

The most basic form of handover is when a phone call in progress is redirected from its current cell (called source) to a new cell (called target). In terrestrial networks the source and the target cells may be served from two different cell sites or from one and the same cell site (in the latter case the two cells are usually referred to as two sectors on that cell site). Such a handover, in which the source and the target are different cells (even if they are on the same cell site) is called inter-cell handover. The purpose of inter-cell handover is to maintain the call as the subscriber is moving out of the area covered by the source cell and entering the area of the target cell.

A special case is possible, in which the source and the target are one and the same cell and only the used channel is changed during the handover. Such a handover, in which the cell is not changed, is called intra-cell handover. The purpose of intra-cell handover is to change one channel, which may be interfered or fading with a new clearer or less fading channel.

Types of handover

In addition to the above classification of inter-cell and intra-cell classification of handovers, they also can be divided into hard and soft handovers:

A hard handover is one in which the channel in the source cell is released and only then the channel in the target cell is engaged. Thus the connection to the source is broken before or 'as' the connection to the target is made—for this reason such handovers are also known as break-before-make. Hard handovers are intended to be instantaneous in order to minimize the disruption to the call. A hard handover is perceived by network engineers as an event during the call. It requires the least processing by the network providing service. When the mobile is between base stations, then the mobile can switch with any of the base stations, so the base stations bounce the link with the mobile back and forth. This is called ping-ponging.

A soft handover is one in which the channel in the source cell is retained and used for a while in parallel with the channel in the target cell. In this case the connection to the target is established before the connection to the source is broken, hence this handover is called make-before-break. The interval, during which the two connections are used in parallel, may be brief or substantial. For this reason the soft handover is perceived by network engineers as a state of the call, rather than a brief event. Soft handovers may involve using connections to more than two cells: connections to three, four or more cells can be maintained by one phone at the same time. When a call is in a state of soft handover, the signal of the best of all used channels can be used for the call at a given moment or all the signals can be combined to produce a clearer copy of the signal. The latter is more advantageous, and when such combining is performed both in the downlink (forward link) and the uplink (reverse link) the handover is termed as softer. Softer handovers are possible when the cells involved in the handovers have a single cell site.

Comparison of handovers

An advantage of the hard handover is that at any moment in time one call uses only one channel. The hard handover event is indeed very short and usually is not perceptible by the user. In the old analog systems it could be heard as a click or a very short beep; in digital systems it is unnoticeable. Another advantage of the hard handoff is that the phone's hardware does not need to be capable of receiving two or more channels in parallel, which makes it cheaper and simpler. A disadvantage is that if a handover fails the call may be temporarily disrupted or even

terminated abnormally. Technologies which use hard handovers, usually have procedures which can re-establish the connection to the source cell if the connection to the target cell cannot be made. However re-establishing this connection may not always be possible (in which case the call will be terminated) and even when possible the procedure may cause a temporary interruption to the call.

One advantage of the soft handovers is that the connection to the source cell is broken only when a reliable connection to the target cell has been established and therefore the chances that the call will be terminated abnormally due to failed handovers are lower. However, by far a bigger advantage comes from the mere fact that simultaneously channels in multiple cells are maintained and the call could only fail if all of the channels are interfered or fade at the same time. Fading and interference in different channels are unrelated and therefore the probability of them taking place at the same moment in all channels is very low. Thus the reliability of the connection becomes higher when the call is in a soft handover. Because in a cellular network the majority of the handovers occur in places of poor coverage, where calls would frequently become unreliable when their channel is interfered or fading, soft handovers bring a significant improvement to the reliability of the calls in these places by making the interference or the fading in a single channel not critical. This advantage comes at the cost of more complex hardware in the phone, which must be capable of processing several channels in parallel. Another price to pay for soft handovers is use of several channels in the network to support just a single call. This reduces the number of remaining free channels and thus reduces the capacity of the network. By adjusting the duration of soft handovers and the size of the areas in which they occur, the network engineers can balance the benefit of extra call reliability against the price of reduced capacity.

Possibility of handover

While theoretically speaking soft handovers are possible in any technology, analog or digital, the cost of implementing them for analog technologies is prohibitively high and none of the technologies that were commercially successful in the past (e.g. AMPS, TACS, NMT, etc.) had this feature. Of the digital technologies, those based on FDMA also face a higher cost for the phones (due to the need to have multiple parallel radio-frequency modules) and those based on TDMA or a combination of TDMA/FDMA, in principle, allow not so expensive implementation of soft handovers. However, none of the 2G (second-generation) technologies have this feature (e.g. GSM, D-AMPS/IS-136, etc.). On the other hand, all CDMA based technologies, 2G and 3G (third-generation), have soft handovers. On one hand, this is facilitated by the possibility to design not so expensive phone hardware supporting soft handovers for CDMA and on the other hand, this is necessitated by the fact that without soft handovers CDMA networks may suffer from substantial interference arising due to the so-called near-far effect.

An Introduction to Handoff in Mobile Cellular Communications

When a mobile user travels from one area of coverage or cell to another cell within a

call’s duration the call should be transferred to the new cell’s base station. Otherwise, the call will be dropped because the link with the current base station becomes too weak as the mobile recedes. Indeed, this ability for transference is a design matter in mobile cellular system design and is call handoff.

Two basic types of handoff are defined -- viz. hard handoff and soft handoff.

With hard handoff, the link to the prior base station is terminated before or as the user is transferred to the new cell’s base station. That is to say that the mobile is linked to no more than one base station at a given time. Initiation of the handoff may begin when the signal strength at the mobile received from base station 2 is greater than that of base station 1. The signal strength measures are really signal levels averaged over a chosen amount of time. This averaging is necessary because of the Rayleigh fading nature of the environment in which the cellular network resides. A major problem with this approach to handoff decision is that the received signals of both base stations often fluctuate. When the mobile is between the base stations, the effect is to cause the mobile to wildly switch links with either base station. The base stations bounce the link with the mobile back and forth. Hence the phenomenon is called ping- ponging. Besides ping ponging this simple approach allows too many handoffs. [1] It has been shown in early studies that much of the time the previous link was well adequate and that handoffs occurred unnecessarily. A better method is to use the averaged signal levels relative to a threshold and hysteresis margin for handoff decision. Furthermore, the condition should be imposed that the target base station’s signal level should be greater than that of the current base station.

The handoff should take place at point A for the choice of Threshold 1 or Threshold 2. The handoff should take place at point B for Threshold 3. In has now been shown in practice that using the hysteresis margin greatly reduces the number of unneeded handoffs. However, there is a delay factor involved here. It will be shown later that one may set up optimum trade off values for the parameters threshold and hysteresis to obtain a tolerable delay.

Because of the increasing demand for wireless services, the available channels within the cells become insufficient to support the growing number of users. To increase the system capacity, techniques such as cell splitting and sectoring may be implemented. Using microcells also improves cellular system capacity, and it is an attractive alternative to the two former mentioned techniques. [2] While the group of cells may maintain a particular area of coverage, the co-channel interference is reduced. Decreasing the co-channel interference increases the system capacity without trunking inefficiency degradation inherent to sectoring. However, innate to microcells is the increase in frequency of handoffs. So we seek efficient decision algorithms to achieve less unnecessary handoffs, yet more reliable handoffs with low blocking probability and low probability of lost calls. Mobiles moving around in microcells will face line of sight (LOS) handoffs and non line of sight (NLOS) handoffs. In the case of NLOS, completely reliable handoffs are difficult to achieve. A problem with microcells is the so called corner effect. When a mobile station moves around a corner such as at a street intersection, there can be a sudden drop in the received signal level. It loses its LOS component with the serving base station. Now if the mobile user does not link up with this new base station B fast enough, the call gets dropped. Furthermore, the mobile can cause interference to the new base station. The base station is unable to regulate the power of the mobile and users within this cell are blocked.

In the cellular design, one could carefully plan so that this can’t happen. That is lay out the cells in such a way that no corner effect will ever be encountered. This cannot always be practically done. Measures are taken in handoff design to help alleviate this problem. We may use a fast forward handoff as the old base station is dropped. Decentralizing the handoff decision, as in the case of the mobile assisted handoff, often achieves this fast forward handoff decision. [1] With decentralizing, it is advantageous that the central switch does not have to make the handoff decisions for every mobile user. This amounts to a saving in system resources.

A problem with faster handoff is that we lose the benefits associated with signal averaging and hysteresis. As was mentioned before, this was helpful in mitigating unnecessary handoffs and ping ponging. However as is now clear, the time of handoff is critical in mircocellular systems and we may not tolerate the delay that comes with hysteresis windows. The handoff must be fast. Now recall that in order to initiate a handoff, the movement of the mobile station from one cell to another must be detected. A reliable method to make this detection and to accommodate the movement is to measure the received signal strengths to the base stations and from the user. In order to avoid excessive and inaccurate handoffs, an averaging of the received signal levels is performed as well as implementing a hysteresis margin. The total handoff delay is the sum of the signal averaging delay and the hysteresis delay. We seek to make this delay small. [3] develops an analytic approach to select the signal averaging time and hysteresis delay in order to obtain an optimum tradeoff between those two parameters as well as a tradeoff between the total delay time and the number of allowable unnecessary handoffs. In [3], some important parameters are given mathematical expressions. It is shown that the probability of an unnecessary handoff is given as:

where f(x) is considered as

L is the difference between the two received signal levels due to the pathloss difference from the two base stations involved in the handoff. And, h is the hysteresis level.

For macrocells, the total delay time is:

T denotes the signal averaging window

K2 represents a path loss constant

Krv represents the normalized distance from the mobile station to base station.

For microcells, the total delay time is:

dcor denotes the drop in signal level experienced at a street corner and is determined experimentally. The analysis shows that there exists compromises between the parameters of averaging time and hysteresis delay. It is evident that for microcells we may wish to choose short averaging time and a larger hysteresis. The converse is clear for macrocells. The main point here is that optimum parameter values may be selected for a tolerable delay in conjunction with some tolerable probability of unnecessary handoff.

By using alternate antenna heights working at different power levels, it is possible to have different size cells coexist within a single geographic framework. Thus may be

implemented the so called umbrella cell consisting of two or more levels. That is a macrocell, which contains perhaps a grid of microcells.

Users in this system are assigned to a particular cellular level based on the mobile transmitter’s speed. [4] The umbrella cell system is used to minimize the many handoffs incurred by high speed mobiles while providing capacity that is inherent to microcells for slow moving users. Handoffs from microcell to microcell can be avoided. Now the slow moving users are placed into the service of a microcell and retain service therein until an increase in mobile transmitter speed overtakes some deciding measure and is therefor urged into a macrocell. However, in the real cellular system, the speed is not really known. Fortunately, there are a couple of common ways to estimate the user speed. One way is to use the statistics of the dwell time. The dwell time is defined as the amount of time over which a call is maintained within a particular cell. Obviously, the dwell time is dependent upon the mobile station’s speed. Based on information of the dwell time, a rough estimate of the user speed may be obtained. Further, the estimate may be improved if the mobile’s past behavior is memorized and accounted for. [3100] Given n dwell times, mobile station speed may be estimated as follows. First assume that the mobile speed is uniform over an interval [a,b]. It is found that the maximum likelihood (ML) estimate is:

and the maximum squared error (MMSE) estimate is:

ci depends on the type of handoff -- i.e. micro to micro, micro to macro etc.

Cellular networkA cellular network or mobile network is a wireless network distributed over land areas called cells, each served by at least one fixed-location transceiver, known as a cell site or base station. In a cellular network, each cell uses a different set of frequencies from neighboring cells, to avoid interference and provide guaranteed bandwidth within each cell.

When joined together these cells provide radio coverage over a wide geographic area. This enables a large number of portable transceivers (e.g., mobile phones, pagers, etc.) to communicate with each other and with fixed transceivers and telephones anywhere in the network, via base stations, even if some of the transceivers are moving through more than one cell during transmission.

Cellular networks offer a number of desirable features:

More capacity than a single large transmitter, since the same frequency can be used for multiple links as long as they are in different cells

Mobile devices use less power than with a single transmitter or satellite since the cell towers are closer

Larger coverage area than a single terrestrial transmitter, since additional cell towers can be added indefinitely and are not limited by the horizon

Major telecommunications providers have deployed voice and data cellular networks over most of the inhabited land area of the Earth. This allows mobile phones and mobile computing devices to be connected to the public switched telephone network and public Internet. Private cellular networks can be used for research[1] or for large organizations and fleets, such as dispatch for local public safety agencies or a taxicab company.[2]

Adjacent and Co-Channel Congestion

Hopefully you have learned why channels 1, 6, and 11 are the best choices for operating your wireless network (this is because 1, 6, and 11 are the only Wi-Fi channels in the 2.4 GHz spectrum that don’t overlap with one another). An open Wi-Fi channel is one of the best gifts to someone setting up a wireless network, but you may not have that option. Recall that overlap is bad because of the “conversational” way that Wi-Fi operates, and often times you will find yourself having to manage congestion. In this newsletter, you’ll learn about adjacent and co-channel congestion, using conversation as a metaphor.

Adjacent channel congestion is the worst type of Wi-Fi interference. To illustrate, think about being at a concert – there’s a band playing really loud, and tons of people, each with their own group of friends. With this much going on, it’s difficult to talk to your friends, and when you start to talk louder, the person next to you has to raise his voice to talk to their group. You’re hearing multiple conversations happening, as well as music from the band, and it seems impossible to communicate.

The diagram below shows a theoretical model of how the above conversation scenario looks when access points on channel 4 (red), channel 6 (green), and channel 5 (blue) are all active at the same time. As one of these APs tries to talk to its clients, its transmissions become garbled because of the transmissions of the other two. This drives down the performance of all of the networks.

An illustration of adjacent channel congestion

In order to explain co-channel congestion, we’ll move our imaginary conversation from a concert venue to a classroom. Think back to your school days – chances are you can think of at least one class that had a student who would talk slower than the other kids, and everyone else would have to wait for their turn to ask a question. Co-channel congestion works in a similar manner: the performance is hindered by the wait times, but the bandwidth is managed, and every device will

get a chance to talk to its associated AP. The diagram below depicts a wireless access point and its associated clients, which can only talk one at a time.

An illustration of co-channel congestion

Co-channel congestion is preferable to adjacent channel congestion because of the way the wireless conversations are managed. As mentioned in our previous newsletter, when choosing a channel that has other networks active, try to keep at least 20dB between the RSSI levels of the networks, as illustrated below:

To recap, an open channel will always be best when deploying your wireless network, but if you have to share a channel, that’s okay too. Adjacent channel congestion is the one you’ll want to avoid if at all possible.

The image below shows what adjacent channel and co-channel congestion look like in inSSIDer. Having a visual representation of where neighboring wireless access points are active is an invaluable tool when planning your own network. It’s easy to see how chaotic adjacent channel congestion is compared to co-channel!

 

Hopefully you now have a good understanding of how Wi-Fi congestion is caused, and how to best deal with it in the 2.4 GHz Band.